Product Data Sheet: Akzonobel Powder Coatings
Product Data Sheet: Akzonobel Powder Coatings
Product Data Sheet: Akzonobel Powder Coatings
3 Commerce Drive
Reading, PA 19607
Tel 610-775-6640
Product Interpon 600 is a range of TGIC powder coatings designed for exterior exposure that offer
Description excellent light and weather resistance from a single coat finish on a variety of substrates.
Powder Properties Chemical type Polyester TGIC
Appearance Smooth
Gloss level (Gardner 60°) >= 80.0 UN
Recommended Film thickness 2.0 – 3.0 mils
Specific gravity 1.67+/-0.05 g/cm³
Coverage @ 1.0 mil 115 sq.ft/lb/mil
Storage Maximum 80°F
Shelf life 12 months, typical
Curing schedule
8 minutes at 375°F
(at object temperature)
Mechanical Tests Flexibility ASTM D522 1/8”
Adhesion ASTM D3359 100%
Impact resistance (Direct) ASTM 2794 140-160 in.lbs.
Hardness ASTM3363 H min.
Environmental and Neutral Salt Spray <1/16” creep, no blisters,
ASTM B117
Durability Tests 500 hrs
Humidity ASTM D2247 No Change at 1000 hours
Exterior Durability Yes
Test Conditions Testing has been determined under laboratory conditions using the following application
properties and is for guidance only.
Substrate CRS
Pretreatment Iron Phosphate (B1000)
Film thickness 2.0 – 3.0 mils
Cure schedule 8 minutes at 375°F
Actual film performance will depend on the individiual circumstances in which the product is
used.
Pre-treatment Steel surfaces to be coated must be clean and free from grease. For maximum protection,
it is essential to pre-treat components prior to the application of Interpon 600. Iron
phosphate and zinc phosphate of ferrous metals improve corrosion resistance.
Application Interpon 600 powders can be applied by manual or automatic electronic spray equipment.
It is recommended that for consistent application and appearance product be fluidized
during application. Unused powder can be reclaimed using suitable equipment and recycled
through the coating system.
JL009QF Page 1 of 2
AkzoNobel Powder Coatings
3 Commerce Drive
Reading, PA 19607
Tel 610-775-6640
Additional Interpon 600 powders have no chalking and slight gloss loss after 12 months Florida
Information exposure but no film breakdown or reduction in protective properties.
This product is UL1332 “Coating, Organic, for Steel Enclosure-use Electrical Equipment –
Component” recognized to UL Designation U1578-1. For UL1332 certifcation all
requirements must be met as designated in File: DTOV2 MH13725. As such, following are
the required application standards that must be met.
Pre-Treatment(s) over
Cure Cure Min. Film
Cycle Window Thickness Cold Hot
Galvanized Galvaneal
(min) (°F) (mils) Rolled Rolled
Steel Steel
Steel Steel
Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the
performance of the product or for any loss or damage arising out of the use of the product. All products supplied and
technical advices given are subject to our standard terms and conditions of sale. You should request a copy of this
document and review it carefully. The information contained in this data sheet is subject to modification from time to
time in the light of experience and our policy of continuous development. It is the user's responsibility to verify that this
data sheet is current prior to using the product.
Brand names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel
http://www.interpon.com/contact-us/
Copyright © 2015 Akzo Nobel Powder Coatings Ltd. Interpon is a registered trademark of AkzoNobel
Product Name: JL009QF
Last Revision Date: 1/12/2016
Revision Number: 1
Author: W.BUCHANAN
JL009QF Page 2 of 2