Multimedia
Multimedia
Multimedia
Product Description 3M™ Pro-Flex™ system is a two component aromatic polyurea designed for
various industrial and manufacturing applications. This product creates a water-
proof seal and is extremely flexible, giving it high impact resistance. Due to the
high elongation and flexibility, this polyurea product has a high COF (Coefficient
of Friction) that creates a great nonskid surface. The product cures rapidly and can
be top-coated with an appropriate long-term UV color stable coating within a few
minutes, if needed.
Typical Physical Note: The following technical information and data should be considered representative
Properties or typical only and should not be used for specification purposes.
Part A Part B
Specific Gravity - ASTM D1475-98 1.10 - 1.30 g/cc 1.00 - 1.20 g/cc
3M™ Pro-Flex™ Polyurea Coating
16336A • 16337B • 16702
Typical Performance Note: The following technical information and data should be considered representative or
Properties typical only and should not be used for specification purposes.
Elcometer Adhesion >1200 psi Sandblasted Steel - Glue Failure ASTM D4541
>800 psi Concrete - Substrate Failure
COF Coefficient of Friction Smooth Surface 2.01 - Rough Surface ASTM D1894
1.89 on James Machine with Leather
COF Coefficient of Friction Smooth Surface .083 - Rough Surface ASTM D2047
1.89 on James Machine with Leather
-2-
3M™ Pro-Flex™ Polyurea Coating
16336A • 16337B • 16702
Typical Performance Note: The following technical information and data should be considered representative
Properties (continued) or typical only and should not be used for specification purposes.
Cleaning Mixers, spray gun, etc. can all be easily cleaned with solvent (acetone) while
product is in the uncured state. In the case that material is allowed to dry on a tool,
scraping and soaking in solvent may be necessary to remove the material.
Directions for Use 1. Follow the Graco E-30 reactor spray equipment start-up procedure.
2. Make sure surface is free from dirt, dust, oil or other contaminants. Clean with
acetone or other quality wax and grease remover.
3. Wire tape and mask.
4. Sand surface with coarse sand paper (36 to 80 grit) and re-clean surface or use
3M™ Metal Prime or 3M™ Lexa-Prime™ (polyurea primers) to eliminate
sanding. Allow primer to cure per directions.
5. Test spray surface for compatibility.
6. Spray first coat and apply second coat in the opposite direction (cross-hatch
technique). Typical thickness per coat is 20 to 30 mils. 3M™ Pro-Flex™ Polyurea
coating reaches handling strength in only in 20 to 30 minutes
Applications Typical use is for a nonskid coating, sound dampening, waterproofing or erosion
protection for wood, fiberglass, concrete, metal & aluminum.
-3-
3M™ Pro-Flex™ Polyurea Coating
16336A • 16337B • 16702
Storage and Handling Keep containers sealed tightly to eliminate any moisture contamination. Do not
introduce water into the liquid components. Use desiccant drier cartridges or
blanket with nitrogen when in use. Part B must be agitated before use. Refer to
MSDS for additional handling and disposal requirements.
(1) Data referred to original sealed drums stored in a dry place at the recommended temperature.
Precautionary Refer to Product Label and Material Safety Data Sheet for Health and Safety Information before using
this product.
Information
Technical Information The technical information, recommendations and other statements contained in this document are
based upon tests or experience that 3M believes are reliable, but the accuracy or completeness
of such information is not guaranteed.
Product Use Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use
and performance of a 3M product in a particular application. Given the variety of factors that can affect
the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and
determining whether it is fit for a particular purpose and suitable for user’s method of application.
Warranty, Unless an additional warranty is specifically stated on the applicable 3M product packaging or product
literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time
Limited Remedy, 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR
and Disclaimer IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY
OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.
If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s
option, replacement of the 3M product or refund of the purchase price.
Limitation of Liability Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product,
whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted,
including warranty, contract, negligence or strict liability.