Pds Luxaprime 1400 Voc

LUXAPRIME 1400
High Build Alkyd Zinc Phosphate Primer
PRODUCT A high build single pack alkyd anti-corrosive primer that can be applied to metals where for
economic or practical reasons blast cleaning is not possible.
DESCRIPTION Pigmented with zinc phosphate anti-corrosive pigments.
Gives a hard tough film that reduces damage during erection.
Reduced health and safety hazards compared to Red Lead Primers
DESIGNED USE Post fabrication primer in new construction projects for conventional systems.
Suitable for interior or exterior environments in moderately aggressive environments.
Can be applied to non-blasted substrates
PHYSICAL DATA VOLUME SOLIDS

50 % + 2 %
(Based on ASTM D2697)
TYPICAL DRY FILM THICKNESS 50 microns
WET FILM THICKNESS 100 microns
THEORETICAL COVERAGE 10.0 m2/litre @ 50 microns DFT
VOC As Supplied
430 gms/ltr
(Based on ASTM D3960)
COLOUR Natural Red Oxide, Grey & off white
FINISH Matt
APPLICATION METHOD OF APPLICATION :

DETAILS This is the recommended method of application:
Maximum 5% Thinner may be added.
AIRLESS SPRAY
Tip Size: 0.43 - 0.54 mm (0.017 - 0.021 in)
Pressure: 110 - 150 kg/cm2 (1600 - 2100 psi)
This is also a suitable method of application.
CONVENTIONAL SPRAY Maximum 20% Thinner may be added
Tip Size: 1.80 - 2.20 mm (0.071 - 0.087 in)
Pressure: 2.75 - 3.45 kg/cm2 (40 - 50 psi)
May be used for difficult shapes or touch-up.
BRUSH OR ROLLER However, additional coats may be required to achieve
the recommended film thickness.
DRYING TIME:
Surface Re coating Interval
Touch Dry Hard Dry
Temperature Minimum Maximum
15C 6 Hrs 24 Hrs 24 Hrs Indefinite
45C 1 hr 8 Hrs 8 Hrs Indefinite
NO. OF COMPONENTS One
Do not apply this product if the Relative Humidity
Application Conditions exceeds 85% or if the substrate temperature is within
3C of the dew point
ADDITIONAL Thinner / Cleaning solvent Solvalux 7-9

Storage Instruction Store in a cool shaded dry area
INFORMATION Flash Point 36C
Packaging 1 USG & 5 USG
Shelf Life 12 months from the date of manufacture.
April 2012 Version 0 Protective Coatings Sales & Service Dubai Tel 04- 3391000 Fax 04-3391322 Abu Dhabi Tel 02-6712207 Fax 02-6713774
LUXAPRIME 1400
High Build Alkyd Zinc Phosphate Primer
SURFACE The life-span and performance of this coating is directly related to the degree of surface
PREPARATION preparation.
Remove all wax, oil and grease by solvent cleaning in accordance with the guide lines given
by SSPC-SPI.
Soluble salts, dirt and dust must be removed prior to coating. Dry brushing should be
sufficient. A freshwater wash must follow to remove all soluble salts.
Remove scale by chipping, needle gun or spot blasting. Any loose or flaking coatings should
be taken back to a firm edge.
Mechanically clean the surface using hand or power tools to a minimum standard of St 2
Swedish Standard SIS 05 59 00 or ISO 8501-1 : 1988 taking care to avoid polishing the
surface.
Where necessary remove weld spatter and round off all rough weld seams and sharp edges to a
smooth surface.
PRODUCT USE Not suitable for use in conjunction with cathodic protection.
RESTRICTIONS Cannot be over coated with 2 pack products & vinyls.
Dry heat resistance up to 80C
May also be applied between 50 and 75 Microns DFT
SAFETY Avoid contact with the skin and eyes. Wear suitable protective clothing such as overalls,
PRECAUTIONS goggles, dust masks and gloves. Use a barrier cream.
Ensure that there is adequate ventilation in the area where the product is being applied. Do not
breathe vapor or spray.
This product is flammable. Keep away from sources of ignition. Do not smoke. Take
precautionary measures against static discharge. In case of fire blanket flames with foam,
carbon dioxide or dry chemicals
Refer to MSDS for further information.
FIRST AID Eyes: In the event of accidental splashes, flush eyes with water immediately and obtain
medical advice
Skin: Wash skin thoroughly with soap and water or approved industrial cleaner.
DO NOT USE solvent or thinners.
Inhalation: Remove to fresh air, loosen collar and keep patient rested.
Ingestion: In case of accidental ingestion, DO NOT INDUCE VOMITING.
Obtain immediate medical attention
The information provided on this data sheet is not intended to be complete and is provided as general advice only. It is the responsibility
DISCLAIMER of the user to ensure that the product is suitable for the purpose for which he wishes to use it. As we have no control over the treatment of
the product, the standard of surface preparation of the substrate, or other factors affecting the use of this product, we are not responsible
for its performance nor would we accept any liability whatsoever or howsoever arising from the use of this product unless specifically
agreed to in writing by us. The information contained in this data sheet may be modified by us from time to time, and without notice, in
the light of our experience and continuous product development.
April 2012 Version 0 Protective Coatings Sales & Service Dubai Tel 04- 3391000 Fax 04-3391322 Abu Dhabi Tel 02-6712207 Fax 02-6713774

Pds Luxaprime 1400 Voc

Uploaded by

Copyright:

Available Formats

Pds Luxaprime 1400 Voc

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pds Luxaprime 1400 Voc

Uploaded by

Copyright:

Available Formats

LUXAPRIME 1400

High Build Alkyd Zinc Phosphate Primer

PHYSICAL DATA VOLUME SOLIDS

APPLICATION METHOD OF APPLICATION :

ADDITIONAL Thinner / Cleaning solvent Solvalux 7-9

You might also like