EPILUX 44

Epoxy Matt Finish

PRODUCT A two component epoxy-polyamide pigmented with durable pigments giving a matt topcoat
DESCRIPTION with:
• High resistance to impact and abrasion.
• Good adhesion to aged epoxy coatings.
• Resistance to spillage or splashes of mild chemicals

DESIGNED USE • A camouflage paint for military tanks and vehicles.

• A matt finishes for steelwork, non-ferrous substrates and concrete.
• Suitable as topcoat for upto C5 Environment as per ISO12944 Part 2.

PHYSICAL DATA VOLUME SOLIDS

52 % + 2 %
(Based on ASTM D2697)
TYPICAL DRY FILM THICKNESS 50 microns
WET FILM THICKNESS 96 microns
THEORETICAL COVERAGE 10.4 m2/litre @ 50 microns DFT
VOC “As Supplied”
418 gms/ltr
(Based on ASTM D3960)
COLOUR Limited Colours
FINISH Matt

APPLICATION METHOD OF APPLICATION :

DETAILS This is the recommended method of application:
Maximum 5% Thinner may be added.
AIRLESS SPRAY
Tip Size: 0.38 - 0.48 mm (0.015 - 0.019 in)
Pressure: 130 - 160 kg/cm2 (1800 – 2300 psi)
This is also a suitable method of application.
CONVENTIONAL SPRAY Maximum 20% Thinner may be added
Tip Size: 1.80 - 2.20 mm (0.071 - 0.087 in)
Pressure: 2.75 - 3.45 kg/cm2 (40 - 50 psi)
May be used for difficult shapes or touch-up.
BRUSH OR ROLLER However, additional coats may be required to achieve
the recommended film thickness. Thinner (max 2%)
DRYING TIME:
Surface Re coating Interval
Touch Dry Hard Dry Pot Life
Temperature Minimum Maximum
15°C 3 Hrs 20 Hrs 24 Hrs 10 Days 10 Hrs
25°C 2 Hrs 16 Hrs 16 Hrs 5 Days 4 Hrs
35°C 1 Hr 8 Hrs 8 Hrs 3 Days 3 Hrs
45°C 40 mins 6 Hrs 6 Hrs 3 Days 1½ Hrs
NO. OF COMPONENTS Two
Mixing Ratio 3 parts Base to 1 part Hardener (by volume)
Do not apply this product if the Relative Humidity
Application Conditions exceeds 85% or if the substrate temperature is within
3°C of the dew point

ADDITIONAL Thinner / Cleaning solvent Solvalux 7-45 / MIL Thinners.

Storage Instruction Store in a cool shaded dry area
INFORMATION Flash Point Mixed 30°C
Packaging 5 liters & 20 liters
Shelf Life 12 months from the date of manufacture.

March 2014 Version 0 Protective Coatings Sales & Service Dubai Tel 04- 3391000 Fax 04-3391322 Abu Dhabi Tel 02-6798202 Fax 02-6713774
 EPILUX 44
Epoxy Matt Finish

SURFACE • This coating is usually applied over EPILUX or ZINCANODE or EPIMASTIC Primers.
PREPARATION
• The surface to be over coated must be dry and free from surface contaminants.

• All wax, oil and grease should be removed by solvent cleaning in accordance with the
guidelines given by SSPC-SPI.

• Soluble salts, dirt and dust must be removed prior to applying the coating. Dry brushing
should be sufficient. A freshwater wash must follow to remove all soluble salts.

• Always ensure the maximum over coating time for the primer/ build coat has not been
exceeded prior to application of EPILUX 44

PRODUCT USE • As common with all epoxies this product will chalk on exposure to direct sunlight.
RESTRICTIONS • Dry heat resistance up to 120°C.
• May also be applied between 30 and 50 Microns DFT.
• Contact Berger Representative for suggesting suitable paint system

SAFETY • Avoid contact with the skin and eyes. Wear suitable protective clothing such as overalls,
PRECAUTIONS goggles, dust masks and gloves. Use a barrier cream.
• Ensure that there is adequate ventilation in the area where the product is being applied. Do not
breathe vapor or spray.
• This product is flammable. Keep away from sources of ignition. Do not smoke. Take
precautionary measures against static discharge. In case of fire – blanket flames with foam,
carbon dioxide or dry chemicals
• Refer to MSDS for further information.

FIRST AID • Eyes: In the event of accidental splashes, flush eyes with water immediately and obtain
medical advice
• Skin: Wash skin thoroughly with soap and water or approved industrial cleaner.
• DO NOT USE solvent or thinners.
• Inhalation: Remove to fresh air, loosen collar and keep patient rested.
• Ingestion: In case of accidental ingestion, DO NOT INDUCE VOMITING.
Obtain immediate medical attention

The information provided on this data sheet is not intended to be complete and is provided as general advice only. It is the responsibility
DISCLAIMER of the user to ensure that the product is suitable for the purpose for which he wishes to use it. As we have no control over the treatment of
the product, the standard of surface preparation of the substrate, or other factors affecting the use of this product, we are not responsible
for its performance nor would we accept any liability whatsoever or howsoever arising from the use of this product unless specifically
agreed to in writing by us. The information contained in this data sheet may be modified by us from time to time, and without notice, in
the light of our experience and continuous product development.

March 2014 Version 0 Protective Coatings Sales & Service Dubai Tel 04- 3391000 Fax 04-3391322 Abu Dhabi Tel 02-6798202 Fax 02-6713774