Catalogo Tophammer PDF

Top hammer drilling tools
Product catalogue
Roc k d r illin g tools

Products from Sandvik Mining and Construction Tools
Top h a m m er p ro d uc t s
www.sandvik.com
Sandvik Mining and Construction Tools AB

SE-811 81 Sandviken, Sweden. Tel +46 26 26 20 00 Fax +46 26 26 23 00
HR-12281-ENG AB Sandvikens Tryckeri

Top hammer products
Small hole drilling 3
Drifting and tunneling 17
Bench drilling 31
Long hole drilling 45
Shank adapters 59
Auxiliary tools 77
Information 82
Index 85
Notes 90
Copyright
Sandviken
This product catalogue is a presentation of the global stock standard range
of top-hammer rock tools manufactured by
Concerning bit diameters
Note that all bits are bigger on diameter than the given measurements in the catalogue.
Cross bits: Can be max 1 mm larger due to manufacturing tolerances.
Button bits: Are max 3,0 mm larger for some designs in order to make up for fast initial
wear on the diameter. The minimum diameter is 1,5 mm above given
measurement.
Keep in mind that a bit always gives a bigger hole than the stated bit diameter.
Bit classification code
H: Very hard to hard rock................ > 2500 bar (250 MPa)

M: Medium hard rock........................ 1500-2500 bar (150-250 MPa)
S: Soft rock....................................... < 1500 bar (150 MPa)
C: Homogeneous (competent) rock

F: Fissured rock
V: Very abrasive rock....................... > 40% silica

A: Abrasive rock............................... 20-40% silica
N: Non-abrasive rock....................... 0-20% silica
Small hole drilling
Small hole drilling
Page
H19 (3/4) Integral drill steels...........................................................5
H22 (7/8") Integral drill steels.........................................................6
Reaming tools....................................................................................7
H22 Tapered tools, 12 taper..........................................................8
H22 Tapered tools, 11 taper...........................................................9
H22 Tapered tools, 7 taper..........................................................10
Stone working tools........................................................................11
R22 (7/8") Extension drilling tools................................................12
R23 (29/32") Extension drilling tools............................................13
R25 (1") Extension drilling tools.....................................................14
Sandvik Alpha. 250 bit thread .....................................................15
4 top hammer drilling tools

Small hole drilling
H19 (3/4) Integral drill steels
Dimensions D Part No.
H19 (3/4)
L D
Series mm ft in mm in
Shank 19 x 108 mm (3/4 x 4 1/4)
21 400 1' 4" 29 19/64" 724-0429
- 800 2' 7" 28 1 7/64" 724-0828
D
- 1600 5' 3" 27 1 1/16" 724-1627
Hex D-19 Hex D-19
- 2400 7' 10" 26 1 1/32" 724-2426
108 L
24 600 2' 27 1 1/16" 724-0627

Hex D
- 1200 3' 11" 26 1 1/32" 724-1226
Boulder- 400 1' 4" 24 15/16" 724-0424

steel 800 2' 7" 23 29/32" 724-0823
Shank 22 x 108 mm (7/8 x 4 1/4)

400 1' 4" 24 15/16" 728-0424
400 1' 4" 29 1 9/64" 728-0429
D
800 2' 7" 28 1 7/64" 728-0828
Hex D-22 Hex D-19
1600 5' 3" 27 1 1/16" 728-1627
108 L
Hex D
top hammer drilling tools 5

Small hole drilling
H22 (7/8) Integral drill steels
H22 (7/8)

L D
Series mm ft in mm in
Shank 22x108 mm (7/8 x 4 1/4)
11 800 2' 7" 34 1 11/32" 714-0834-65
1600 5' 3" 33 1 19/64" 714-1633-65
D
2400 7' 10" 32 1 1/4" 714-2432-65
Hex D-22 Hex D-22
3200 10' 6" 31 1 7/32" 714-3231
108 L
4000 13' 1" 30 1 3/16" 714-4030
4800 15' 9" 29 1 9/64" 714-4829
Hex D
5600 18' 4" 28 1 7/64" 714-5628-50
6400 21' 27 1 1/16" 714-6427-50
7200 23' 8" 26 1 1/32" 714-7226-50
12 800 2' 7" 40 1 37/64" 714-0840-65

1600 5' 3" 39 1 17/32" 714-1639-65
2400 7' 10" 38 1 1/2" 714-2438-65
3200 10' 6" 37 1 29/64" 714-3237-65
4000 13' 1" 36 1 27/64" 714-4036-65
4800 15' 9" 35 1 3/8" 714-4835-65
5600 18' 4" 34 1 11/32" 714-5634-65
6400 21' 33 1 19/64" 714-6433-65
7200 23' 8" 32 1 1/4" 714-7232-65
13 400 1' 4" 34 1 11/32" 714-0434-65

800 2' 7" 33 1 19/64" 714-0833-65
1200 3' 11" 32 1 1/4" 714-1232-65
1600 5' 3" 31 1 7/32" 714-1631
2000 6' 7" 30 1 3/16" 714-2030
16 600 2' 35 1 3/8" 714-0635-65

1200 3' 11" 34 1 11/32" 714-1234-65
1800 5' 11" 33 1 19/64" 714-1833-65
2400 7' 10" 32 1 1/4" 714-2432-65
17 600 2' 41 1 5/8" 714-0641-65

1200 3' 11" 40 1 37/64" 714-1240-65
1800 5' 11" 39 1 17/32" 714-1839-65
2400 7' 10" 38 1 1/2" 714-2438-65
2000 6' 7" 33 1 19/64" 714-2033-65

8000 26' 3" 26 1 1/32" 714-8026-50
8800 28' 11" 25 1" 714-8825-5005
9600 31' 6" 25 1" 714-9625-5005
800 2' 7" 29 1 9/64" 714-0829

1600 5' 3" 28 1 7/64" 714-1628-50
2400 7' 10" 27 1 1/16" 714-2427-50

Small hole drilling
H22 Reaming tools
H22 Reaming
Hex D
L D
mm ft in mm in
Pilot rod, Hex 22, 6 taper
800 2' 7 1/2" 26 1 1/32" 7922-6108-11
1200 3' 11 3/4" 26 1 1/32" 7922-6112-11
2000 6' 6 3/4" 26 1 1/32" 7922-6120-11
Hex D-22 Hex D-22 2500 8' 2 1/2" 26 1 1/32" 7922-6124-11
108 L
D
Buttons, mm Angle Dimensions D Part No.

Front Gauge
No Size No Size mm in
Reaming tools for cut holes / Reaming bit, 6 taper
4x8 8x9 25 64 2 1/2" 7722-4864-S45
4x10 8x10 30 76 3" 7722-4876-S45
6x10 8x10 30 89 3 1/2" 7722-4889-S45
D

Small hole drilling
H22 Tapered tools, 12 taper
Bits Flushinghole, mm Buttons, mm Angle Dimensions D Part No.

H22 -12
Front Gauge Front Gauge

No Size No Size No Size No Size mm in
Button bit
1x5 1x5 1x7 4x7 35 28 1 1/8" 7795-6428-B48
1x5 1x5 1x7 4x7 35 30 1 3/16" 7795-6430-B48
D
Button bit
2x4 1x4 2x7 5x7 40 32 1 1/4" 7795-5232-B48
2x4 1x3,5 2x7 5x8 40 35 1 3/8" 7795-5235-B48
D 2x4 1x4 2x7 5x9 40 38 1 1/2" 7795-5238-B48
Button bit
2x4 1x3.5 2x7 5x7 40 33 1 9/64" 7770-5233-B48
2x4 1x3.5 2x7 5x8 40 35 1 3/8" 7770-5235-B48
D
Cross bit
1x4 2x4 30 1 3/16" 7770-9030-42
1x6 2x4.5 32 1 1/4" 7770-9032-42
D
1x6 2x4.5 35 1 3/8" 7770-9035-42
Rods Hex D
Dimensions D
L Hex D
Part No.
mm ft in mm in
Tapered rod, shank 22x108, carburized
610 2' 22 7/8" 7870-6106-11
Hex D-22
1220 4' 22 7/8" 7870-6112-11
1830 6' 22 7/8" 7870-6118-11
2000 6' 7 22 7/8" 7870-6120-11
108 L
2440 8' 22 7/8" 7870-6124-11
3050 10' 22 7/8" 7870-6131-11
3200 10' 6 22 7/8" 7870-6132-11
3660 12' 22 7/8" 7870-6137-11
Tapered rod, shank 22x108, HF-hardened - For surface drilling
2440 8' 22 7/8" 7870-5124-11
Hex D-22
3200 10' 6 22 7/8" 7870-5132-11
4000 13' 1 1/2 22 7/8" 7870-1140-11
4400 14' 5 22 7/8" 7870-1144-11
108 L 4800 15' 9 22 7/8" 7870-1148-11
5600 18' 4 1/2 22 7/8" 7870-1156-11
6400 21' 22 7/8" 7870-1164-11
7200 23' 7 1/2 22 7/8" 7870-1172-11
8000 26' 3 22 7/8" 7870-1180-11
8800 28' 10 1/2 22 7/8" 7870-1188-11

Small hole drilling
H2 -11
Button bit
1x6 2x4 2x7 3x8 35 32 1 1/4" 7776-1932-B48
1x6 1x6 1x8 3x9 40 36 1 7/16" 7776-1936-B48
D 1x6 1x6 2x8 3x9 40 38 1 1/2" 7776-1938-B48
1x6 1x6 2x8 3x9 40 40 1 37/64" 7776-1940-B48
Button bit
1x4 1x6 2x7 5x7 40 32 1 1/4" 7776-4432-B48
1x5 1x5 2x7 5x7 35 35 1 3/8" 7776-4435-B48
D 1x6 1x5 2x7 5x8 35 38 1 1/2" 7776-4438-B48
1x6 1x5 2x8 5x9 35 40 1 37/64" 7776-4440-B48
Rods Hex D
Dimensions D
L Hex D
Part No.
mm ft in mm in
610 2' 22 7/8" 7876-6106-11
Hex D-22
800 2 7 1/2 22 7/8 7876-6108-11
1220 4' 22 7/8" 7876-6112-11
1830 6' 22 7/8" 7876-6118-11
108 L 2000 6 7 22 7/8 7876-6120-11
2440 8' 22 7/8" 7876-6124-11
3050 10' 22 7/8" 7876-6131-11
3600 11' 9 1/2 22 7/8" 7876-6136-11

Small hole drilling

H22 -7

Button bit
2x4 1x4 2x7 5x7 40 32 1 1/4" 7788-5232-B48
2x4 1x4 2x7 5x7 40 33 1 9/64 7788-5233-B48
D 2x4 1x3.5 2x7 5x8 40 35 1 3/8" 7788-5235-B48
2x4 1x5 2x7 5x8 35 38 1 1/2" 7788-5238-B48
Rods Hex D
Dimensions D
L Hex D
Part No.
mm ft in mm in
2400 8' 22 7/8" 7888-6124-11
Hex D-22 3200 10' 6 22 7/8" 7888-6132-11
108 L

Small hole drilling
Stone working tools
Stone tools
Hex D
L D
mm ft in mm in
Plug hole integral steel
150 6" 17 21/32" 721-1517
Hex D-19
160 6 1/4" 20 25/32" 721-1620
D
200 7 7/8" 20 25/32" 721-2020
240 9 29/64" 20 25/32" 721-2420
108 L
280 11 1/32" 20 25/32" 721-2820
310 11 1/4" 20 25/32" 721-3120
160 6 1/4" 22 7/8" 721-1622
190 7 1/2" 22 7/8" 721-1922

Small hole drilling
R22 (7/8) Extension drilling tools
R22 (7/8)
Cross bit Flushinghole, mm

Front Gauge
Buttons, mm
Front Gauge
Angle Dimensions D Part No.

Cross bit
1 4.5 2 4.5 38 1 1/2" 7731-1038-42

Hex D
L D
mm ft in mm in
Extension rod R22 - Hex 22 - R22
Hex D-22 800 2' 7" 22 7/8" 7851-1308-20
1200 3' 11" 22 7/8" 7851-1312-20
1600 5' 3" 22 7/8" 7851-1316-20
R 22 R 22
L
Shank adapter/Shank rod, Hex 22 - R22

Hex D-22 255 10 3/64" 22 7/8" 7801-6103-13
1000 3' 3" 22 7/8" 7801-6110-13
R 22
108 L
Coupling sleeve, R22

140 5 1/2" 31 1 7/32" 7991-2031

Small hole drilling
R23 (29/32) Extension drilling tools
R23 (29/32)
Bits Flushinghole, mm
Front Gauge
Buttons, mm
Front Gauge
Angle Dimensions D Bit
Classifi-
Part No.
cation
Button bit
1x4 1x6 2x7 5x7 35 33 1 5/16" HMCA 7737-4433-R48
1x5 1x6 2x7 5x8 40 35 1 3/8" HMCA 7737-5235-R48
D 1x6 1x6 2x7 5x8 35 38 1 1/2" HMCA 7737-4438A-R48
1x5 1x6 2x8 5x9 35 41 1 5/8" HMCA 7737-5241-R48
Button bit
3x5 3x8 6x9 30 45 1 3/4" HMCA 7737-5345-R48
Rods Hex D
Dimensions D
L Hex D
Part No.
mm ft in mm in
MF-rod, R23 - Hex 22 - R23
Hex D-22 2095 6' 10 1/2" 22 7/8" 7857-4821-20
3050 10' 22 7/8" 7857-4831-20
R 23 R23
L
Female end 31 mm
Shank adapter / Shank rod, Hex 22 - R23
Hex D-22 255 10 3/64" 22 7/8" 7807-6103-11
2400 8' 22 7/8" 7807-6124-11
3200 10' 22 7/8" 7807-6132-11
R 23
3600 11' 9 5/8 22 7/8" 7807-6136-11
108 L
Shank rod, Hex 25 - R23

255 10 3/64" 25 1" 7807-7103-11
Hex D-25
3600 11' 9" 25 1" 7807-7136-11
R 23
108 L

Small hole drilling
R25 (1) Extension drilling tools
Bits Flushinghole, mm Buttons, mm Angle Dimensions D Bit Part No.

R25 (1)
Classifi-
cation
Button bit
1x5 1x6 2x7 5x8 35 35 1 3/8" HMCA 7732-4435-S48
1x5 1x6 2x7 5x9 30 38 1 1/2" HMCA 7732-5238-S48
D
1x5 1x6 2x7 5x9 35 38 1 1/2" HMCA 7732-5238-R48
1x5 1x6 2x8 5x9 35 41 1 5/8" HMCA 7732-5241-S48
Button bit
3x4.5 3x8 6x9 40 45 1 3/4" MSCFAN 7732-5345F-R48
Rods Hex D
Dimensions D
L Hex D
Part No.
mm ft in mm in
Shank adapter / rod, Hex 22 x R25
Hex D-22
255 10 3/64" 22 7/8" 7802-6103-13
800 2' 7" 22 7/8" 7802-6108-13
1000 3' 3" 22 7/8" 7802-6110-13
R 25
108 L
Extension rod, R25 - Hex 25 - R25

Hex D-25 915 3' 25 1" 7852-2309-20
1220 4' 25 1" 7852-2312-20
1525 5' 25 1" 7852-2315-20
R 25 R 25 1830 6' 25 1" 7852-2318-20
L 2435 8' 25 1" 7852-2324-20
3050 10' 25 1" 7852-2331-20

160 6 1/4" 35 1 3/8" 7992-2035
D
- For one-rod drilling

Small hole drilling
Sandvik Alpha. 250 bit thread
Bits Flushinghole, mm Buttons, mm Angle Dimensions D Bit

Classifi-
Part No.
250
cation
Button bit
1x5 1x6 2x7 5x8 40 35 1 3/8" HMCA 7764-5235-R48
1x5 1x6 2x7 5x9 35 38 1 1/2" HMCA 7764-5238-R48
D
Button bit
3x4.5 3x8 6x9 40 45 1 3/4" MSCFAN 7764-5345F-R48
Rods Hex D
Dimensions D
L Hex D
Part No.
mm ft in mm in
Shank rod, Hex 25 - 250
3600 11' 9 5/8 " 25 1" 7814-7136-11
Hex D-25
250
108 L

Drifting and tunneling
Page
R25 (1") bit thread..........................................................................19
R28 (1 1/8") bit thread...................................................................21
R32 (1 1/4") bit thread ..................................................................22
Sandvik Alpha. 330 bit thread ....................................................25
R35 (1 3/8") bit thread . ................................................................27
Sandvik Extra. R35 (1 3/8") bit thread..........................................29
Sandvik RT300 bits..........................................................................30

R25 (1) bit thread
Front Gauge
Buttons, mm
Front Gauge
Classifi-
Part No.
cation
RT300 button bit, type 52
1x4,5 1x6 2x7 5x7 45 33 1 5/16" HMCA 7732-4433C-S48
1x5 1x6 2x7 5x9 30 35 1 3/8" HMCA 7732-4435-S48
D
R25 (1)
1x5 1x6 2x7 5x9 30 37 1 29/64" HMCA 7732-5237-S48
1x5 1x6 2x7 5x9 30 38 1 1/2" HMCA 7732-5238-S48
1x5 1x6 2x8 5x9 35 41 1 5/8" HMCA 7732-5241-S48
Cross bit
1x5 2x5 33 1 5/16" - 7732-1633-42
1x5 2x5 35 1 3/8" - 7732-1435-42
D
Rods Hex D
Dimensions D
L D
Part No.
mm ft in mm in
Drifter rod, R32 - Hex 25 - R25
Hex D-25 1870 6' 1 5/8" 25 1" 7853-2418-20
2175 7' 1 5/8" 25 1" 7853-2421-20
2475 8' 1 1/2" 25 1" 7853-2424-20
R 32 R 25 2630 8' 7 1/2" 25 1" 7853-2426-20
L 2785 9' 1 5/8" 25 1" 7853-2427-20
Flushing hole 8,8 mm 2935 9' 7 1/2" 25 1" 7853-2429-20
3090 10' 1 5/8" 25 1" 7853-2431-20

150 5 29/64" 44 1 47/64" 7993-3644

R25 (1") reaming tools
Thread Dimensions D Part No.

L D
mm ft in mm in
Reaming tools for cut holes / Pilot adapter, 6 taper
R25 - - - 26 1 1/32" 7822-2526
R25 (1)

Front Gauge
4x8 8x9 25 64 2 1/2" 7722-4864-S45
4x10 8x10 30 76 3" 7722-4876-S45
6x10 8x10 30 89 3 1/2" 7722-4889-S45

R28 (1 1/8) bit thread
Front Gauge
Buttons, mm
Front Gauge
Classifi-
Part No.
cation
1x5 1x6 2x7 5x9 35 38 1 1/2" MCAN 7739-5238-R48
1x5 1x6 2x7 5x9 30 38 1 1/2" HMCA 7739-5238-S48
R28 (1 1/8)
D
1x5 1x6 2x8 5x9 35 41 1 5/8" HMCA 7739-5241-S48
1x5 1x6 2x8 5x10 30 43 1 11/16 HMCA 7739-5243-S48
Cross bit
1x5 2x5 - - 38 1 1/2" 7739-1438-42
Reaming tools Thread Dimensions D

L D
Part No.
mm ft in mm in
R28 - - - 26 1 1/32" 7822-1526

Front Gauge
4x8 8x9 25 64 2 1/2" 7722-4864-S45
4x10 8x10 30 76 3" 7722-4876-S45
6x10 8x10 30 89 3 1/2" 7722-4889-S45
D
Rods Hex D
Dimensions D
L D
Part No.
mm ft in mm in
Hex D-28 3090 10' 1 5/8" 28 1 1/8" 7853-7631-20
3700 12' 1 5/8" 28 1 1/8" 7853-7637-20
4305 14' 1 1/2" 28 1 1/8" 7853-7643-20
R 32 R 25
L
Flushing hole 8,8 mm
150 5 29/64" 44 1 47/64" 7993-3644

Front Gauge
Buttons, mm
Front Gauge
Classifi-
Part No.
cation
1x5 2x6 2x9 5x10 35 43 1 11/16" HMCVA 7733-5243A-S48
1x5 2x6 2x9 5x11 30 45 1 3/4" HMCVA 7733-5245A-S48
R32 (1 1/4)
D
1x6 2x7.5 2x9 5x11 35 48 1 7/8" HMCVA 7733-5248A-S48
1x6 2x7.5 2x10 5x12 35 51 2" HMCVA 7733-5251A-S48

2x6 2x6 2x9 6x9 40 43 1 11/16" MSCAN 7733-5443B-R48
2x6 2x6 2x9 6x10 35 45 1 3/4" MSCAN 7733-5445B-R48
D

3x4.5 1x5 3x8 6x10 25 45 1 3/4" HMCAN 7733-5345A-S48
3x4.5 1x5 3x8 6x10 30 45 1 3/4" MSCAN 7733-5345A-R48
D 3x5 1x5 3x9 6x10 30 48 1 7/8" HMCAN 7733-5348A-S48
3x5 1x5 3x9 6x10 30 48 1 7/8" HMCAN 7733-5348A-R48
D 3x6 1x6 3x9 6x10 35 51 2" MSCAN 7733-1651A-S48

3x6 1x6 3x9 6x10 35 51 2" MSCAN 7733-1651A-R48
D - - 3x9 6x9 - 4 1 3/4" SCN 7733-5745A-C48
Cross bit
1x5 4x6 - - - 45 1 3/4" 7733-1345A-42

Rods Hex D
Dimensions D
L D
Part No.
mm ft in mm in
Hex D-35 3090 10' 1 5/8" 35 1 3/8" 7854-9631-20
3700 12' 1 5/8" 35 1 3/8" 7854-9637-20
R32 (1 1/4)
4305 14' 1 1/2" 35 1 3/8" 7854-9643-20
R 38 R 32 4915 16' 1 1/2" 35 1 3/8" 7854-9649-20
L

Hex D-32 3090 10' 1 5/8" 32 1 1/4" 7854-8631-20
3700 12' 1 5/8" 32 1 1/4" 7854-8637-20
4305 14' 1 1/2" 32 1 1/4" 7854-8643-20
R 38 R 32
4915 16' 1 1/2" 32 1 1/4" 7854-8649-20
L

Drifter rod, T38 - Hex 32 - R32
Hex D-32 3700 12' 1 5/8" 32 1 1/4" 7324-8637-20
4305 14' 1 1/2" 32 1 1/4" 7324-8643-20
T 38 R 32
L

Hex D-35 3090 10' 1 5/8" 35 1 3/8" 7324-9631-20
3700 12' 1 5/8" 35 1 3/8" 7324-9637-20
4305 14' 1 1/2" 35 1 3/8" 7324-9643-20
T 38 R 32 4915 16' 1 1/2" 35 1 3/8" 7324-9649-20
L
5525 18' 1 1/2" 35 1 3/8" 7324-9655-20
6135 20' 1 1/2" 35 1 3/8" 7324-9661-20

Coupling sleeve
R38 170 - 6 3/4" 55 2 5/32" 7994-3655
T38 191 - 7 1/2" 52 2" 7314-3652
D

R32 (1 1/4") reaming tools
Pilot adapters 6, 12 taper Thread Dimensions D

L D
Part No.
mm ft in mm in
R32 - - - 26 1 1/32" 7822-3526
R32 (1 1/4)

R32 - - - 40 1 37/64" 7821-3440
Reaming bit 6, 12 taper Buttons, mm

Front Gauge
4x8 8x9 25 64 2 1/2" 7722-4864-S45
4x10 8x10 30 76 3" 7722-4876-S45
6x10 8x10 30 89 3 1/2" 7722-4889-S45
D

4x10 8x12 35 89 3 1/2" 7721-4889-S45
4x12 8x12 35 102 4" 7721-4802-S45
8x12 8x12 35 127 5" 7721-4827-S45
D
Reaming bit Flushinghole, mm

Front Gauge
Buttons, mm
Front Gauge

Reaming tools for cut holes / Reaming bit, R32
2x6 2x6 9x13 8x13 35 102 4" 7733-5602-S45

Front Gauge
Buttons, mm
Front Gauge
Classifi-
Part No.
cation
1x5 1x7.5 2x9 6x10 35 43 1 11/16" HMCVA 7766-5243A-S48
1x5 1x7.5 2x9 5x11 30 45 1 3/4" HMCVA 7766-5245A-S48
D
1x6 2x7.5 2x9 5x11 35 48 1 7/8" HMCVA 7766-5248A-S48
330
2x6 2x6 2x9 6x9 40 43 1 11/16" MSCAN 7766-5443B-R48
2x6 2x6 2x9 6x10 35 45 1 3/4" MSCAN 7766-5445B-R48
D

3x4.5 1x5 3x8 6x10 30 45 1 3/4" MSCAN 7766-5345A-R48
3x4.5 1x5 3x8 6x10 25 45 1 3/4" HMCAN 7766-5345A-S48
D 3x5 1x5 3x9 6x10 30 48 1 7/8" MSCAN 7766-5348A-R48
3x5 1x5 3x9 6x10 30 48 1 7/8" HMCAN 7766-5348A-S48
D 3x6 1x6 3x9 6x10 35 51 2" MSCAN 7766-1651A-R48

3x6 1x6 3x9 6x10 35 51 2" HMCAN 7766-1651A-S48
Cross bit
1x5 4x6 45 1 3/4" 7766-1345A-42
Rods Hex D
Dimensions D
L D
Part No.
mm ft in mm in
Drifter rod, T38 - Hex 35 - 330
Hex D-35 3090 10' 1 5/8" 35 1 3/8" 7324-4131-20
3700 12' 1 5/8" 35 1 3/8" 7324-4137-20
4305 14' 1 1/2" 35 1 3/8" 7324-4143-20
T 38 330 4915 16' 1 1/2" 35 1 3/8" 7324-4149-20
L 5525 18' 1 1/2" 35 1 3/8" 7324-4155-20

Drifter rod, T38 - Round 39 - 330
4915 16' 1 1/2" 39 1 1/2" 7324-4249-20
5525 18' 1 1/2" 39 1 1/2" 7324-4255-20
6135 20' 1 1/2" 39 1 1/2" 7324-4261-20
T 38 D 330 6440 21' 1 1/2" 39 1 1/2" 7324-4264-20
L

Rods Dimensions D
L D
Part No.
mm ft in mm in
Coupling sleeve, T38
191 - 7 1/2" 52 2" 7314-3652
D
330

Front Gauge
Buttons, mm
Front Gauge

Reaming tools for cut holes / Reaming bit, 330
4x6 - 7x13 8x13 35 102 4" 7766-5602P-S48
Pilot adapter 12 taper Thread Dimensions D

L D
Part No.
mm ft in mm in
330 - - - 40 1 37/64" 7821-3040
Reaming bit 12 taper Buttons, mm

Front Gauge
4x10 8x12 35 89 3 1/2" 7721-4889-S45
4x12 8x12 35 102 4" 7721-4802-S45
8x12 8x12 35 127 5" 7721-4827-S45
D

Front Gauge
Buttons, mm
Front Gauge
Classifi-
Part No.
cation
1x5 1x7.5 2x9 5x11 35 48 1 7/8" HMCVA 7738-5248-S48
R35 (1 3/8)
D

3x5 1x5 3x9 6x10 30 48 1 7/8" HMCAN 7738-5348A-S48
3x5 1x5 3x9 6x10 30 48 1 7/8" MSCAN 7738-5348A-R48
D
D 3x6 1x6 3x9 6x10 35 51 2" HMCAN 7738-1651A-S48

3x6 1x6 3x9 6x10 35 51 2" MSCAN 7738-1651A-R48
Cross bit
1x5 2x7.5 48 1 7/8" 7738-1448-42
Rods Hex D
Dimensions D
L D
Part No.
mm ft in mm in
4305 14' 1 1/2" 35 1 3/8" 7324-8543-20
4915 16' 1 1/2" 35 1 3/8" 7324-8549-20
5525 18' 1 1/2" 35 1 3/8" 7324-8555-20
Hex D-35 R 35
T 38 6135 20' 1 1/2" 35 1 3/8" 7324-8561-20
L
Drifter rod, T38 - Round 39 - R35
4305 14' 1 1/2" 39 1 1/2" 7324-7243-20
4915 16' 1 1/2" 39 1 1/2" 7324-7249-20
5525 18' 1 1/2" 39 1 1/2" 7324-7255-20
T 38 D R 35 6135 20' 1 1/2" 39 1 1/2" 7324-7261-20
L
Coupling sleeve, T38
191 7 1/2" 52 2" 7314-3652


Front Gauge
Buttons, mm
Front Gauge

Reaming tools for cut holes / Reaming bit, R35
2x6 2x6 9x13 8x13 35 102 4" 7738-5602-S45
R35 (1 3/8)
Pilot adapter 12 taper Thread Dimensions D

L D
Part No.
mm ft in mm in
R35 - - - 40 1 37/64" 7821-5440
Reaming bit 12 taper Buttons, mm

Front Gauge
4x10 8x12 35 89 3 1/2" 7721-4889-S45
4x12 8x12 35 102 4" 7721-4802-S45
8x12 8x12 35 127 5" 7721-4827-S45
D

Sandvik Extra. R35 (1 3/8) bit thread
Front Gauge
Buttons, mm
Front Gauge
Classifi-
Part No.
cation
Button bit, Retrac R35
3x6 1x5 3x9 6x11 30 54 2 1/5" MSCFAN 7738-4654A1-R48
R35 (1 3/8)
D
Rods Dimensions D
L D
Part No.
mm ft in mm in
Drifter rod, T35 - Round 39 - R35
4305 14 1 1/2" 39 1 1/2 7327-5243-20
4915 16' 1 1/2" 39 1 1/2" 7327-5249-20
5525 18' 1 1/2" 39 1 1/2" 7327-5255-20
T 35 D R 35 6135 20' 1 1/2" 39 1 1/2" 7327-5261-20
L
Flushing hole 14,5 mm, Female end 48,2 mm
Drifter Extension rod, T35 - Round 39 - T35
3050 10' 39 1 1/2" 7327-4731-20
3660 12 39 1 1/2 7327-4737-20
4265 14 39 1 1/2 7327-4743-20
T 35 D T 35 4875 16 39 1 1/2 7327-4749-20
L
Flushing hole 14,5 mm, Female end 48,2 mm

Sandvik RT300 bits
Sandvik RT300 bits for drifting and tunneling are available in three basic designs
Type 52
Designed for hard and abrasive rock
Type 53
Allround design for most types of rock
Type 54
Designed for soft and less abrasive rock

Bench drilling
Bench drilling

Bench drilling
Page
R32 (1 1/4").....................................................................................33
T35(1 3/8").....................................................................................35
T38 (1 1/2")....................................................................................36
T45 (1 3/4").....................................................................................38
T51 (2")............................................................................................40
Sandvik GT60 ................................................................................42

Bench drilling
R32 (1 1/4")
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
Button bit
3x6 1x6 3x9 6x10 35 51 2" HMCA 7733-1651A-S48
3x6 1x6 3x9 6x10 35 51 2" MSCAN 7733-1651A-R48
D
3x6 1x6 3x10 6x11 35 57 2 1/4" HMCA 7733-1657A-S48
3x7 3x11 6x12 30 64 2 1/2 HMCVA 7733-1664-S48
Button bit, Retrac

3x6 3x9 6x10 35 51 2" HMCFA 7733-4651-S48
R32 (1 1/4)
3x6 3x9 6x10 35 51 2" MSCFAN 7733-4651-R48
D
3x8 3x11 6x12 30 64 2 1/2" HMCFVA 7733-4664-S48
Cross bit
1x5 2x7.5 51 2" HMCFA 7733-1451-42
Guide bit
3x6 3x8 6x10 40 51 2" 7733-8251-R48

Bench drilling
R32 (1 1/4")
Rods Dimensions D
Bit L D
Part No.
dia. mm ft in mm in
mm
Guide tube
51-64 3050 10' 46 1 3/4" 7953-4631-20
R 32 D R 32
L
Female end 46 mm
MF-rod, R32 - round 32 - R32
R32 (1 1/4)
3050 10' - 32 1 1/4" 7853-5131-20

3660 12' - 32 1 1/4" 7853-5137-20
R 32 D R 32
L
Flushing hole 9.2 mm. Wrench flat 25.4 mm. Female end 45 mm
Extension rod, R32 - round 32 - R32
3050 10' - 32 1 1/4" 7853-3331-30
3660 12' - 32 1 1/4" 7853-3337-30
R 32 D R 32
L
Flushing hole 11.7 mm. Wrench flat 25.4 mm
Coupling sleeve R32
150 - 5 29/32" 44 1 47/64" 7993-3644

Bench drilling
T35(1 3/8")
Front Gauge
Buttons, mm
Front Gauge
Classification
Part No.

Button bit, regular skirt
3x6 1x6 3x9 6x10 35 64 2 1/2 HMCFVAN 7517-1654A-S48
Button bit, Retrac T35
T35 (1 3/8)
3x6 3x9 6x10 35 54 2 1/6" MSCFAN 7517-4654-R48
3x7 3x10 6x11 35 57 2 1/4" MSCFAN 7517-4657-R48
D
Rods Dimensions D
L D
Part No.
mm ft in mm in
MF-rod, T35 - Round 39 - T35
3050 10' - 39 1 1/2" 7327-4731-20
3660 12' - 39 1 1/2" 7327-4737-20
4265 14' - 39 1 1/2" 7327-4743-20
D
T 35 T 35
L
Female end 45 mm. Flushing hole 14,5 mm

Bench drilling
T38 (1 1/2")
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
3x8 3x11 6x12 30 64 2 1/2" HMCVAN 7514-1664-S48
3x8 3x11 6x12 35 64 2 1/2" MSCAN 7514-1664-R48
D
4x8 5x9 8x10 35 64 2 1/2" MSCAN 7514-1864-R48

4x8 5x10 8x11 30 70 2 3/4" HMCVAN 7514-1870-S48
T38 (1 1/2)
D 4x8 5x11 8x12 35 76 3" HMCVAN 7514-1876-S48

4x8 5x11 8x11 40 76 3 MSCAN 7514-1876-R48
4x9 5x12 8x12 35 89 3 1/2 HMCVAN 7514-1889-S48
Button bit, Retrac
3x8 3x11 6x12 30 64 2 1/2 HMCFVAN 7514-4664-S48
3x8 3x11 6x12 35 64 2 1/2 MSCFAN 7514-4664-R48
D
4x8 5x9 8x10 35 64 2 1/2" MSCFAN 7514-4864-R48

D 4x8 5x10 8x11 30 70 2 3/4 HMCFVAN 7514-4870-S48
4x8 5x11 8x12 35 76 3 HMCFVAN 7514-4876-S48
4x8 5x11 8x11 40 76 3 MSCFAN 7514-4876-R48
X bit
1x7.5 2x7.5 64 2 1/2" 7514-4064-11
1x7.5 2x7.5 76 3" 7514-4076A-11
D
Guide bit
3x8 1x8 4x9 6x11 35 64 2 1/2" MSCFAN 7514-8264-R48

Bench drilling
T38 (1 1/2")
Rods Hex D
Dimensions D
Bit dia. L D
Part No.
mm mm ft in mm in
Guide tube
64-76 3660 12' 56 2 13/64" 7955-5637-20
T 38 D T 38
L
Female end OD 56 mm
MF-rod, T38 - round 39 - T38
T38 (1 1/2)
3050 10' 39 1 1/2" 7324-4731-70
3660 12' 39 1 1/2" 7324-4737-70
4265 14' 39 1 1/2" 7324-4743-70
T 38 D T 38
L
Flushing hole 14.5 mm. Female end OD 56 mm

Extension rod, T38 - round 39 - T38
3050 10' 39 1 1/2" 7324-4331C-30
3660 12' 39 1 1/2" 7324-4337C-30
T 38 D T 38
L
Flushing hole 14.5 mm. Wrench flat 32 mm
Light extension rod, T38 - Hex 32 - T38
3050 10' 32 1 1/4" 7324-6931-20
T 38 D T 38
L
Flushing hole 9.6 mm
Coupling sleeve T38
191 7 1/2" 55 2 5/32" 7314-3355

Bench drilling
T45 (1 3/4")
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
4x8 5x10 8x11 30 70 2 3/4" HMCVAN 7515-1870-S48
4x8 5x11 8x12 35 76 3" HMCVAN 7515-1876-S48
D 4x8 5x11 8x12 35 76 3 MSCAN 7515-1876-R48
4x9 5x13 8x13 35 89 3 1/2 HMCVAN 7515-1889-S48
4x9 5x13 8x13 40 89 3 1/2 HMCAN 7515-1889-R48
T45 (1 3/4)
3x10 9x11 9x13 35 102 4" HMCVAN 7515-1902-S48

D
3x10 9x11 9x13 40 102 4" MSCAN 7515-1902-R48
Button bit, Retrac

4x8 5x10 8x11 35 70 2 3/4 MSCFAN 7515-4870-R48
4x8 5x11 8x12 35 76 3 HMCFVAN 7515-4876-S48
D 4x8 5x11 8x12 35 76 3 MSCFAN 7515-4876-R48
4x9 5x13 8x13 35 89 3 1/2 HMCFVAN 7515-4889-S48
4x9 5x13 8x13 40 89 3 1/2 MSCFAN 7515-4889-R48
3x10 9x11 9x13 35 102 4 HMCFVAN 7515-4902-S48

D
3x10 9x11 9x13 40 102 4 MSCFAN 7515-4902-R48
Guide bit
4x8 6x10 8x11 35 76 3" MSCFAN 7515-8276-R48
4x10 6x11 8x12 40 89 3 1/2" MSCFAN 7515-8289-R48
D

Bench drilling
T45 (1 3/4")
Rods Dimensions D
Bit dia. L D
Part No.
mm mm ft in mm in
Guide tube
76-89 3660 12' 63 2 1/2" 7956-6337-70
89-102 3660 12' 76 3" 7956-7637-70
T 45 D T 45
L
Female end 63 mm / 76 mm
T45 (1 3/4)
3050 10' 46 1 3/4" 7325-7731-70
3660 12' 46 1 3/4" 7325-7737-70
4265 14' 46 1 3/4" 7325-7743-70
T 45 D T 45
L 6095 20' 46 1 3/4" 7325-7761-70
Flushing hole 17 mm. Female end 63 mm

3050 10' 46 1 3/4" 7325-7331C-30
3660 12' 46 1 3/4" 7325-7337C-30
4265 14' 46 1 3/4" 7325-7343C-30
T 45 D T 45
L
Flushing hole 17 mm
Coupling sleeve T45
210 8 1/8" 63 2 31/64" 7315-3663

Bench drilling
T51 (2")
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
4x10 5x13 8x13 35 89 3 1/2 HMCVAN 7516-1889-S48
4x10 5x13 8x13 40 89 3 1/2 MSCAN 7516-1889-R48
D
T51 (2)
3x13 9x11 9x13 40 102 4" MSCAN 7516-1902-R48

D 3x13 9x11 9x13 35 102 4" HMCVAN 7516-1902-S48
3x14 10x12 9x14 35 115 4 1/2" HMCVAN 7516-1915-S48
3x14 10x13 9x14 35 127 5" HMCVAN 7516-1927-S48
Button bit, Retrac

4x10 5x13 8x13 35 89 3 1/2 HMCFVAN 7516-4889-S48
4x10 5x13 8x13 40 89 3 1/2 MSCFAN 7516-4889-R48
D
3x13 9x11 9x13 40 102 4 MSCFAN 7516-4902-R48

3x13 9x11 9x13 35 102 4 HMCFVAN 7516-4902-S48
D 3x14 10x12 9x14 40 115 4 1/2 HMCFVAN 7516-4915-R48
3x14 10x12 9x14 35 115 4 1/2 HMCFVAN 7516-4915-S48
3x14 10x13 9x14 35 127 5 HMCFVAN 7516-4927-S48

Bench drilling
T51 (2")
Rods Dimensions D
Bit dia. L D
Part No.
mm mm ft in mm in
Guide tube
89-102 3660 12' 76 3" 7957-7637-70
102-127 3660 12' 87 3 1/2" 7957-8737-70
T 51 D T 51
L
Female end 76 / 87 mm
T51 (2)
3660 12' 52 2" 7326-5537-70
4265 14' 52 2" 7326-5543-70
6095 20' 52 2" 7326-5561-70
T 51 D T 51
L
Flushing hole 21.5 mm. Female end 71 mm

3660 12' 52 2" 7326-5337C-30
4265 14' 52 2" 7326-5343C-30
6095 20' 52 2" 7326-5361C-30
T 51 D T 51
L
Flushing hole 21.5 mm

Coupling sleeve T51
225 8 7/8" 71 2 51/64" 7316-3671
225 8 7/8" 76 3" 7316-3676
D

Bench drilling
Sandvik GT60
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
4x11 6x12 8x14 35 92 3 5/8" HMSCVA 7620-1892-S48
4x11 6x12 8x14 35 96 3 3/4" HMSCVA 7620-1896-S48
D
3x14 9x11 9x13 35 102 4" HMSCVA 7620-1902-S48

GT60
3x14 10x12 9x14 40 115 4 1/2 MSCAN 7620-1915-R48

3x14 10x12 9x14 35 115 4 1/2" HMSCVA 7620-1915-S48
D
3x14 10x14 9x16 35 127 5" HMSCVA 7620-1927-S48
3x14 10x14 9x16 35 140 5 1/2" HMSCVA 7620-1940-S48
3x14 12x14 9x16 35 152 6 HMSCVA 7620-1952-S48
Button bit, Retrac

3x14 9x11 9x13 35 102 4" HMSCFVA 7620-4902-S48
3x14 9x11 9x13 40 102 4" MSCFAN 7620-4902-R48
3x14 10x12 9x14 40 115 4 1/2 MSCFAN 7620-4915-R48
D 3x14 10x12 9x14 35 115 4 1/2" HMSCFVA 7620-4915-S48
3x14 10x14 9x16 35 127 5" HMSCFVA 7620-4927-S48
3x14 10x14 9x16 35 140 5 1/2 HMSCFVA 7620-4940-S48
3x14 12x14 9x16 35 152 6 HMSCFVA 7620-4952-S48
2x14 9x12 9x12 40 92 3 5/8" MSCFAN 7620-8792-R48

D 2x14 9x12 9x12 40 96 3 3/4 MSCFAN 7620-8796-R48
2x14 10x12 9x13 40 102 4" MSCFAN 7620-8702-R48
3x13 6x13 9x16 35 115 4 1/2" HMCFVA 7620-8115-S48

D

Bench drilling
Sandvik GT60
Rods Dimensions D
L D
Part No.
mm ft in mm in
MF-rod, GT60 - Round 60 (64) - GT60. For bits from 96 mm.
3660 12' - 60 2 3/8" 7610-1137-70
4265 14' - 60 2 3/8" 7610-1143-70
6095 20' - 60 2 3/8" 7610-1161-70
GT60 D GT60
L
4265 14' - 64 2 1/2" 7610-1243-70
GT60
GT60 D GT60
L
Female end 85 mm. Flushing hole 25 mm
MF-rod, GT60 - Round 60 - GT60. For 92-115 mm bits.

4265 14' - 60 2 3/8" 7610-1443-70
GT60 D GT60
L
Pilot tube
4265 14' 87 3 1/2" 7640-8743-70
5335 17' 6" 76 3" 7640-7653-70
GT60 GT60
D
L
Female end 85 mm ( 82 mm on 76 mm tubes)
Drill tube
4265 14' 87 3 1/2" 7660-8743-71
GT60 GT60
D
L
Always use with tube shank adapter 7600-6030-01 (HL1500, 1560) or 7600-6031-01 (HL1000, 1010)

Long hole drilling underground
Page
R32 (1 1/4")......................................................................................................47
T35 (1 3/8").....................................................................................................49
T38 (1 1/2").....................................................................................................50
T45 (1 3/4")......................................................................................................52
T51 (2").............................................................................................................54
T45 (1 3/4") tube drilling tools.......................................................................56
ST58 (2 1/4") tube drilling tools......................................................................57
ST68 (2 3/4") tube drilling tools......................................................................58

R32 (1 1/4")
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
Button bit
3x6 1x6 3x9 6x10 35 51 2" HMCA 7733-1651A-S48
3x6 1x6 3x9 6x10 35 51 2" MSCAN 7733-1651A-R48
D
3x6 1x6 3x10 6x11 35 57 2 1/4" HMCA 7733-1657A-S48
3x7 3x11 6x12 30 64 2 1/2 HMCVA 7733-1664-S48
Button bit, Retrac

3x6 3x9 6x10 35 51 2" HMCFA 7733-4651-S48
3x6 3x9 6x10 35 51 2" MSCFAN 7733-4651-R48
D
3x8 3x11 6x12 30 64 2 1/2" HMCFVA 7733-4664-S48
Cross bit
R32 (1 1/4)
1x5 2x7.5 51 2" HMCFA 7733-1451-42
Guide bit
3x6 3x8 6x10 40 51 2" 7733-8251-R48

R32 (1 1/4")
Rods Dimensions D
Bit L D
Part No.
dia. mm ft in mm in
mm
Guide tube
51-64 1830 6' 46 1 3/4" 7953-4618-20
R 32 D R 32
L
Female end 46 mm
MF-rod, R32 - round 32 - R32
915 3' 32 1 1/4" 7853-5109-20
1220 4' 32 1 1/4" 7853-5112-20
1525 5' 32 1 1/4" 7853-5115-20
R 32 D R 32
1830 6' 32 1 1/4" 7853-5118-20
L
R32 (1 1/4)
Flushing hole 9.2 mm. Wrench flat 25.4 mm. Female end 45 mm
Extension rod, R32 - round 32 - R32
915 3' 32 1 1/4" 7853-3309-20
1220 4' 32 1 1/4" 7853-3312-20
1525 5' 32 1 1/4" 7853-3315-20
R 32 D R 32 1830 6' 32 1 1/4" 7853-3318-20
L
Flushing hole 11.7 mm. Wrench flat 25.4 mm

Coupling sleeve R32
150 - 5 29/32" 44 1 47/64" 7993-3644
Pilot adapter Thread Dimensions D

L D
Part No.
mm ft in mm in
Pilot adapter for reaming of 51 mm (2) pilot holes
R32 47 1 7/8" 7823-3647
Reamer Buttons, mm
Front Gauge
Classifica-
Part No.
tion
Reaming bit
4x12 8x12 35 102 4" 7723-4802-S45
4x12 8x12 35 127 5 7723-4827-S45
D

T35 (1 3/8")
Front Gauge
Buttons, mm
Front Gauge
Classification
Part No.

3x6 1x6 3x9 6x10 35 64 2 1/2 HMCFVAN 7517-1654A-S48
Button bit, Retrac T35

3x6 3x9 6x10 35 54 2 1/6" MSCFAN 7517-4654-R48
3x7 3x10 6x11 35 57 2 1/4" MSCFAN 7517-4657-R48
D
T35 (1 3/8)
Rods Dimensions D
L D
Part No.
mm ft in mm in
MF-rod, T35 - Round 39 - T35
1830 6' - 39 1 1/2" 7327-4718-20
D
T 35 T 35
L
Female end 48,2 mm. Flushing hole 14,5 mm

T38 (1 1/2")
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
3x8 3x11 6x12 30 64 2 1/2" HMCVAN 7514-1664-S48
3x8 3x11 6x12 35 64 2 1/2" MSCAN 7514-1664-R48
D
4x8 5x9 8x10 35 64 2 1/2" MSCAN 7514-1864-R48

D 4x8 5x10 8x11 30 70 2 3/4" HMCVAN 7514-1870-S48
4x8 5x11 8x12 35 76 3" HMCVAN 7514-1876-S48
4x8 5x11 8x11 40 76 3 MSCAN 7514-1876-R48
Button bit, Retrac
3x8 3x11 6x12 30 64 2 1/2 HMCFVAN 7514-4664-S48
3x8 3x11 6x12 35 64 2 1/2 MSCFAN 7514-4664-R48
T38 (1 1/2)
4x8 5x9 8x10 35 64 2 1/2" MSCFAN 7514-4864-R48

D 4x8 5x10 8x11 30 70 2 3/4 HMCFVAN 7514-4870-S48
4x8 5x11 8x12 35 76 3 HMCFVAN 7514-4876-S48
4x8 5x11 8x11 40 76 3 MSCFAN 7514-4876-R48
Guide bit
3x8 1x8 4x9 6x11 35 64 2 1/2" MSCFAN 7514-8264-R48

T38 (1 1/2")
Rods Dimensions D
Bit dia. L D
Part No.
mm mm ft in mm in
Guide tube
64-76 1830 6' 56 2 13/64" 7955-5618-20
T 38 D T 38
L
Female end OD 56 mm
1220 4' 39 1 1/2" 7324-4712C-20
1525 5' 39 1 1/2" 7324-4715C-20
1830 6' 39 1 1/2" 7324-4718C-20
T 38 D T 38
L
T38 (1 1/2)
Flushing hole 14.5 mm. Female end OD 56 mm
Pilot adapter Thread Dimensions D

L D
Part No.
mm ft in mm in
Pilot adapter for reaming of 51 mm (2) pilot holes
T38 47 1 7/8" 7823-2647
Reamer Buttons, mm
Front Gauge
Classifica-
Part No.
tion
Reaming bit
4x12 8x12 35 102 4" 7723-4802-S45
4x12 8x12 35 127 5 7723-4827-S45
D

T45 (1 3/4")
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
4x8 5x10 8x11 35 70 2 3/4" HMCVAN 7515-1870-S48
4x8 5x11 8x12 35 76 3" HMCVAN 7515-1876-S48
D 4x8 5x11 8x12 35 76 3 MSCAN 7515-1876-R48
4x9 5x13 8x13 35 89 3 1/2 HMCVAN 7515-1889-S48
4x9 5x13 8x13 40 89 3 1/2 MSCAN 7515-1889-R48
Button bit, Retrac

4x8 5x10 8x11 35 70 2 3/4 MSCFAN 7515-4870-R48
4x8 5x11 8x12 35 76 3 HMCFVAN 7515-4876-S48
D 4x8 5x11 8x12 35 76 3 MSCFAN 7515-4876-R48
4x9 5x13 8x13 35 89 3 1/2 HMCFVAN 7515-4889-S48
4x9 5x13 8x13 40 89 3 1/2 MSCFAN 7515-4889-R48
T45 (1 3/4)
Guide bit
4x8 6x10 8x11 35 76 3" MSCFAN 7515-8276-R48
4x10 6x11 8x12 40 89 3 1/2" MSCFAN 7515-8289-R48
D
Reaming bit
3x14 9x14 35 127 5 7515-5627-S45
7x14 8x14 35 152 6 7515-5652-S45

T45 (1 3/4")
Rods Dimensions D
Bit dia. L D
Part No.
mm mm ft in mm in
Guide tube
76-89 1830 6' 63 2 31/64" 7956-6318-21
T 45 D T 45
L
Female end 63 mm / 76 mm
1525 5' 46 1 3/4" 7325-7715C-20
1830 6' 46 1 3/4" 7325-7718C-20
T 45 D T 45
L
Flushing hole 17 mm. Female end 63 mm
T45 (1 3/4)

T51 (2")
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
4x10 5x13 8x13 35 89 3 1/2 HMCVAN 7516-1889-S48
4x10 5x13 8x13 40 89 3 1/2 MSCAN 7516-1889-R48
D
3x13 9x11 9x13 40 102 4" MSCAN 7516-1902-R48

D 3x13 9x11 9x13 35 102 4" HMCVAN 7516-1902-S48
T51 (2)
Button bit, Retrac

4x10 5x13 8x13 35 89 3 1/2 HMCFVAN 7516-4889-S48
4x10 5x13 8x13 40 89 3 1/2 MSCFAN 7516-4889-R48
D
3x13 9x11 9x13 40 102 4 MSCFAN 7516-4902-R48

D 3x13 9x11 9x13 35 102 4 HMCFVAN 7516-4902-S48
Reaming bit
7x14 8x14 35 152 6 7516-5652-S45

T51 (2")
Rods Dimensions D
Bit dia. L D
Part No.
mm mm ft in mm in
Guide tube
89-102 1830 6' 76 3" 7957-7618-20
T 51 D T 51
L
Female end 76 / 87 mm
1525 5 52 2 7326-5515C-20
1830 6' 52 2" 7326-5518C-20
T 51 D T 51
L
Flushing hole 21.5 mm. Female end 71 mm
T51 (2)

T45 (1 3/4") tube drilling tools
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
XDC, button bit
4x7.5 6x10 8x11 35 76 3" HMCVA 7525-8476-R65
Tubes Dimensions D
L D
Part No.
mm ft in mm in
T45 Tube
Drill tube, T45 - Round 65 - T45

1525 5' 65 2 1/2" 7985-6315-26
1830 6' 65 2 1/2" 7985-6318-26
T 45 D T 45
L
Flushing hole 18 mm

ST58 (2 1/4") tube drilling tools
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
XDC, button bit
4x10 6x12 8x12 35 89 3 1/2" HMCVA 7528-8489-R65
Button bit, Heavy Duty

2x15 6x12 8x14 35 89 3 1/2" HCV 7528-6989-S65
ST58 Tube
Reaming bit
7x14 8x14 35 152 6 7528-5652-S65
Tubes Dimensions D
L D
Part No.
mm ft in mm in
Drill tube, ST58 - Round 76 - ST58
1525 5' 76 3" 7378-7615-26
1830 6' 76 3" 7378-7618-26
ST58 D ST58
L
Flushing hole 26 mm

ST68 (2 3/4") tube drilling tools
Front Gauge
Buttons, mm
Front Gauge
Classifica-
Part No.
tion
XDC, button bit
4x10 8x12 10x12 35 102 4" HMCVA 7529-8402-R65
4x10 8x14 10x14 35 115 4 1/2" HMCVA 7529-8415-R65
D
Button bit, Heavy Duty

2x15 5x14 8x16 35 102 4" HCV 7529-6902-S65
XDC, button bit, guide

ST68 Tube
4x10 8x12 10x12 35 102 4" HMCVA 7529-7302-R65

4x10 8x14 10x14 35 115 4 1/2" HMCVA 7529-7315-R65
D
Collaring bit
3x18 8x16 9x16 35 152 6" 7529-6652-S45
Reaming bit
3x16 9x16 35 152 6 7529-5652C-S65
Tubes Dimensions D
L D
Part No.
mm ft in mm in
Drill tube, ST68 - Round 87 - ST68
1525 5' 87 3 1/2" 7379-8715-26
1525 5' 87 3 1/2" 7379-8715-46
1830 6' 87 3 1/2" 7379-8718-26
1830 6' 87 3 1/2" 7379-8718-46
ST68 D ST68
L
Flushing hole 30 mm
Permanent back flow valve.

Shank adapters
Shank adapters
Page
Hexagonal shank adapters..............................................................61
Sandvik............................................................................................ 62
Atlas Copco.................................................................................... 67
Boart............................................................................................... 70
Furukawa........................................................................................ 71
T45 Tube
Gardner-Denver, Ingersoll-Rand & Klemm.................................. 72
Montabert...................................................................................... 73
SIG....................................................................................................74
Secoma........................................................................................... 75
Toyo.................................................................................................76
Shank adapter dimensions:

Metric scale (mm)
Rock drill categories:

BE = bench drilling
BO = bolting
DS = dimensional stone drilling
PD = production drilling underground (long hole drilling)
TU = drifting and tunneling

Shank adapters
Hexagonal shank adapters Hex D

Flushing
tube (mm)
Thread Length
(mm)
Part No.
For hexagonal bushing 22 x 108 mm

Hex D-22 4.5-5.0 R22 255 7801-6103-13
4.5-5.0 R23 255 7807-6103-11
4.5-5.0 R25 255 7802-6103-13
108 L
For hexagonal bushing 25 x 108 mm

Hex D-25 4.5-5.0 R23 255 7807-7103-11
4.5-5.0 R25 255 7802-7103-14
108 L
ST58 Tube
For hexagonal bushing 25 x 159
Hex D-25 8 R25 255 7802-7503-20
Hexagonal
159 L
No packing. Not suitable for hydraulic machines with water flushing.

Shank adapters
Sandvik
Application Flushing Thread Length Part No.

hole (mm)
(mm)
HL 300
BE R32 400 7803-7549-01
58,8
39 32
10
L
HL 300S
BO,TU R28 245 7809-7547-01
BO,TU R32 245 7803-7547-01
58,8
39 45 10
L
L400, L410, L500, L510, L550

BO, PD, TU 10 R32 380 7803-3602-30
48
31,7 32 20,5
20
L
Sandvik
HLR 438L and HLR 438T

BE, TU 12.07 R32 380 7803-4700-50
57 BE, TU 12.07 T38 400 7304-4700-50
38 37 38 25,7
L
HLR 438LS, 438TS, HL 538, HL538L, L550S

BE, PD, TU R32 450 7803-4700-01
TU R38 450 7804-4700-01
57
BE, PD, TU T38 455 7304-4700-01
38 38
37 25,7 BE T38 545 7304-4706-01
L
HL 500-38 / 510-38
BE R32 550 7803-7535-02
58,8 BE T35 550 7307-7535-02
BE T38 550 7304-7535-02
38 10
49 BE R38 550 7804-7535-02
L
- 38 = For 38 mm front head, S=For underground drilling

Shank adapters
Sandvik

hole (mm)
(mm)
HL 500-45 / 510-45
BE T35 550 7307-7557-01
58,8 BE T38 550 7304-7557-01
BE T45 550 7305-7557-01
49 45 10
BE R32 550 7803-7557-01
L
HL 500 S-38 / 510 S-38 / 510 B / 510 LH

PD,TU R32 460 7803-7531-01
58,8 TU R38 460 7804-7531-01
PD,TU T38 460 7304-7531-01
49 38 10
TU R38 500 7804-7536-01
L
PD,TU T38 500 7304-7536-01
HL 500 F / 510 F
BO R32 350 7803-7553-01
58,8
58 45 10
L
HL 550 SUPER / 560 SUPER / 510 S-45
Sandvik
TU T35 460 7307-7566-01
PD,TU T35 550 7307-7557-01
58,8
TU R38 500 7804-7554-01
49 45 10 TU T38 500 7304-7554-01
L
HLX 1
TU,BO R23 235 7807-7570-01
TU,BO R25 255 7802-7567-01
39
25 28 5,4
L
HLX 5 / HLX 5T
TU R32 500 7803-7585-01
TU T35 500 7307-7585-01
58,7
TU T38 500 7304-7585-01
49 45 7,9 TU R38 500 7804-7585-01
L BE R32 575 7803-7586-01
BE T35 575 7307-7586-01
BE T38 575 7304-7586-01
BE T45 575 7305-7586-01
HLX5 PE-45
TU R32 575 7803-7664-01
58,7 TU T38 575 7304-7664-01
126 45 9,9
L
- 38, -45 = For 38 or 45 mm front head, S=For underground drilling

Shank adapters
Sandvik

hole (mm)
(mm)
HL 600-45 / 600 S-45
BE R32 600 7803-7532-01
BE T38 600 7304-7532-01
60
Tubes, BE T45 600 7305-7532-01
40 45 10
75 TU,PD T38 525 7304-7537-01
L TU,PD T45 525 7305-7537-01
HL 600-52
BE T45 650 7305-7551-01
BE T51 650 7306-7551-02
60
40 52 10
75
L
HL 645
BE T38 600 7304-7541-02
BE T45 600 7305-7541-02
59
44 45
Sandvik
68
L
HL 650-45 / 700-45 / 700T-45 / 710-45 / 800T-45

BE T38 600 7304-7576-01
BE T45 600 7305-7576-01
69
45
95 12,9
L
HL 650-52, 700-52 / PE-52 / S-52, 710-52 / S-52 / PE-52 / SPE-52, 800T-52 / PE-52
BE,PD T38 600 7304-7577-02
BE T45 600 7305-7577-02
69
BE T51 600 7306-7577-03
95 52 12,9
L
HL 850S
BE, PD T45 670 7305-7400-01
69
47 52
80 14
L
-45, -52 = For 45 or 52 mm front head, PE= For Power Extractor rock drill (reverse hammering), S=For underground drilling

Shank adapters
Sandvik

hole (mm)
(mm)
HL 1000-52 / 1000 S-52
BE T45 670 7305-6010-01
BE T51 670 7306-6010-02
79
PD T45 590 7305-6008-01
75 52 PD T51 590 7306-6008-01
14
L
HL 1000-60
BE T51 670 7306-6014-02
BE GT60 670 7600-6014-02
79
75 60 14
L
HL 1000-80, Shoulder drive

BE GT60 670 7600-6031-01
79
75
Sandvik
80 14
L
HL 1000 S-80 Tube drilling

PD ST58 635 7328-6009-02
PD ST68 640 7329-6009-02
79
75 80 14
L
HL 1000 PE-52
BE T51 840 7306-6019-02
79
136 52 14
L Suited only for early drills with the long type of Power
Extractor with 52 mm bearing diameter
HL 1000 PE-65 / HL 1500 PE-65 / HL 1560 T-65
BE T51 760 7306-6025-02
BE GT60 760 7600-6025-02
79
111 65 14
L
-52, -60, -65, -80 = For 52, 60, 65 or 80 mm front head, PE= For Power Extractor rock drill (reverse hammering), S=For underground drilling

Shank adapters
Sandvik

hole (mm)
(mm)
HL 1500-52 / 1500 T-52
BE T51 710 7306-6021-02
79
111,5 52
14
L
HL 1500-60 / 1500 T-60

BE T51 760 7306-6022-02
BE GT60 760 7600-6022-03
79
111,5 60
14
L
HL 1500 T-80, Shoulder drive

BE GT60 760 7600-6030-01
79
75
Sandvik
80 14
L
HL 1500 S-80 Tube drilling

PD ST58 635 7328-6020-01
PD ST68 635 7329-6020-01
79
111,5 80 14
L
HL 1500 SPE-90 Tube drilling

PD ST58 635 7328-6035-01
PD ST68 635 7329-6035-01
79 BE GT60 760 7600-6032-01
111
90 14
L
-52, -60, -65, -80, -90 = For 52, 60, 65, 80 and 90 mm front head, PE= For Power Extractor rock drill, S=For underground drilling, T= Drill with stabilizer

Shank adapters
Atlas Copco

hole (mm)
(mm)
Atlas Copco BBC 43, 44, 45 and 100
TU 10 R32 380 7803-3100-30
48
32 19 32
20,5
L
Atlas Copco BBC 51, 52, 54 and 120

TU 10 R32 380 7803-4200-30
57,2 TU 10 T38 390 7304-4200-30
38
32 25,4
L
Atlas Copco BBE 57

BE 14 T38 537 7304-7502-60
64,4
Atlas Copco
44,5 44,5
80 13,4
L
Atlas Copco COP 125, 130 and 131

TU,BE,PD 14 T38 380 7304-4500-60
52
38 38
32
L
Atlas Copco COP 1032 HD

TU,BO R32 340 7803-3588-01
54
34 45
58 9
L
TU,BO R38 340 7804-3575-01

54
34
58 55 9
L
Atlas Copco COP 1032

BE T35 550 7307-3576-01
54
34 45 9
58
L

Shank adapters
Atlas Copco

hole (mm)
(mm)
Atlas Copco COP 1032 LE
BE,DS R32 550 7803-3576-01
54
34 45 9
58
L
Atlas Copco COP 1036/1038 HB

BE R32 500 7803-3591-01
54 BE T38 500 7304-3591-01
34 38 9
74
L
54 BE T45 500 7305-3591-01
34 45 9
74
L
Atlas Copco COP 1038 HD/1238

TU R32 485 7803-3590-03
Atlas Copco
54 TU R38 485 7804-3590-03

TU T38 485 7304-3590-03
34 38 9
74
L
Atlas Copco COP 1038 HL

BE,PD R32 575 7803-3593-01
54 BE,PD T38 575 7304-3593-01
34 38 9
74
L
54 BE,PD T45 575 7305-3593-01

34 45 9
74
L

TU T38 435 7304-3666-01
53,4
38 8,8
84,5
L
TU T45 435 7305-3667-01
53,4 TU T35 440 7307-3668-01
TU,PD T35 525 7307-3671-01
84,5 45 8,8
L

Shank adapters
Atlas Copco

hole (mm)
(mm)
BE R32 500 7803-3591-01
54 BE T38 500 7304-3591-01
TU R38 485 7804-3590-03
34 38 9
74 TU T38 485 7304-3590-03
L
54 BE T45 500 7305-3591-01

34 45 9
74
L
BE,PD R32 575 7803-3593-01

54 BE,PD T35 575 7307-3593-01
34 38 BE,PD T38 575 7304-3593-01
9
74
L
Atlas Copco
BE,PD T38 575 7304-3550-01
54
BE,PD T45 575 7305-3593-01
34 45 9
74
L
Atlas Copco COP 1432, COP 1532, COP1440, COP1838 HD/ME
TU R38 435 7804-3652-01
TU T35 435 7307-3652-01
54
TU T38 435 7304-3652-01
45 9
84,5 TU R32 435 7803-3652-01
L
BO R32 525 7803-3656-01

54 BE T35 525 7307-3656-01
38 BO T38 525 7304-3656-01
84,5 9
L
Atlas Copco COP 1432 Female

TU R38 341 7804-3670-02
TU R32 341 7803-3670-02
54
84,5 55 9
L

PD R32 500 7803-3583-01
37,8
78,5 35 5,7
L

Shank adapters
Atlas Copco and Boart

hole (mm)
(mm)
Atlas Copco COP 1550, COP 1838 ME/ HE
BE,PD T38 525 7304-3655-01
BE,PD T45 525 7305-3655-01
54
BE,PD T51 525 7306-3655-02
84,5 52 9
L
Atlas Copco COP 1550 EX, COP 1838 EX

BE T38 730 7304-3825-02
53,9 BE T45 730 7305-3826-02
60 8,8
94
L
Atlas Copco COP 1840 HE, COP 1850

BE,PD T35 565 7307-3690-01
BE,PD T38 565 7304-3690-02
54
BE,PD T45 565 7305-3690-02
125 52 9 BE,PD T51 565 7306-3690-03
L
Atlas C./Boart
Atlas Copco COP 2150, COP 2550

BE T51 770 7306-3692-01
53,4
124,5 60 8,8
L
Atlas Copco COP 2160, COP 2560

BE T51 770 7306-3689-01
61,4
124,5 60 6,4
L
Atlas Copco COP 4050 EX
PD ST68 805 7329-3716-01
68
70 11,2
136
L
Atlas Copco COP 4050 MUX

PD ST68 835 7329-3720-01
68
112 90 11,2
L
Boart HD 125, HD 150, HD 160

TU R38 495 7804-4993-01
66,1 TU T38 495 7304-4993-01
38 45
64 15
L

Shank adapters
Furukawa

hole (mm)
(mm)
Furukawa M 120 and PD 200
BE 14 R32 330 7803-7500-61
BE 14 T38 380 7304-7543-60
55,5
BE 14 T38 446 7304-7500-60
44,5 64 44,5 18,2
L
Furukawa PD 200R
BE 14 T38 484 7304-7581-60
71
44 69 44
21
L
Furukawa HD 260, HD 300

BE 16 T38 655 7304-7526-80
BE 16 T45 655 7305-7526-80
64,4
44 45
79 21
L
Furukawa
Furukawa HD 609
BE T38 620 7304-4791-01
56,9 BE T38 690 7304-4780-01
35,5 BE T45 620 7305-4791-01

45 9,9
75
L
Furukawa HD 612
BE T45 710 7305-7414-01
64,9
41,5 45
89 11,75
L
Furukawa HD 709
BE T38 620 7304-7426-01
83
45
93 10
L
Furukawa HD 712
BE T45 788 7305-7417-01
71,8
51
99,5 12,3
L

Shank adapters
Gardner-Denver, Ingersoll-Rand and Klemm

hole (mm)
(mm)
Gardner-Denver PR 123
TU,BE 14 R32 330 7803-7500-61
TU,BE 14 R32 380 7803-7543-60
55,5
TU 14 R38 350 7804-7500-60
44,5 64 44,5 TU,BE 14 T38 446 7304-7500-60
18,2
L TU,BE 14 T38 380 7304-7543-60
Ingersoll-Rand URD 475, URD 550, VL120, EVL 130, VL140 and F16
BE 14 R32 330 7803-7500-61
BE 14 R32 380 7803-7543-60
55,5
BE 14 T38 380 7304-7543-60
44,5 64 44,5 BE 14 T38 446 7304-7500-60
18,2
L
Ingersoll-Rand YH 65, YH 80
BE 19 T38 495 7304-7525-19
BE 19 T45 500 7305-7525-19
64,3
46 85 45
L 13,5
G-K
Ingersoll-Rand YH 80 A
BE 19 T45 495 7305-7559-19
64,3
46 85 51 13,5
L
Ingersoll-Rand YH 65 RP, YH 70 RP, YH 75 RP, YH 80 RP

BE 19 T45 700 7305-7546-19
64,8
46 45
119 13,5
L
Klemm 4053
BE R55 500 7805-6015 1)
BE R55 500 7805-7015 2)
74
46 154 56,5 1) LH-Rotation

L 8,5
2) RH-Rotation

Shank adapters
Montabert

hole (mm)
(mm)
Montabert HC40
BE R32 447 7803-4725-01
52,7 BE R38 447 7804-4725-01
58 38
8,4
L
Montabert HC40 (female)

TU, BO R32 270 7803-4726-01
52,6
58 52,5 8,4
L
Montabert HC 80, HC 90, HC 105

TU R38 440 7804-4720-01
52,7 TU T38 440 7304-4720-01
TU T38 500 7304-4723-01
97 38 8,4
L
Montabert
Montabert H 100
BE 14 T38 537 7304-7502-60
64,4
44,5 80 44,5
13,4
L
Montabert HC 80R, HC 105R, HC 107R, HC 108R, HC 109R

BE T38 670 7304-7544-01
59,6
40 45
99 9,4
L
Montabert HC 80, HC 120

BE T45 490 7305-7520-01
59,7
95 45 9,4
L
Montabert HC 120R, HC 150R, HC 155R, HC 158R

BE T51 670 7306-7528-02
59,7
102 51 9,4
L
Montabert HC 200A
BE T51 840 7306-7530-02
73 BE GT60 840 7600-7530-02
138 60 11,4
L
Shank adapters
SIG

hole (mm)
(mm)
SIG HBM 50, 100 and 120
BO R32 340 7803-3588-01
54
34 45
58 9
L
SIG HBM 100 and 120

TU, BO R38 340 7804-3575-01
54
34
58 55 9
L
SIG HBM 50, 100 and 120

BE, DS R32 550 7803-3576-01
54
34 45 9
58
L
SIG
SIG 101
BE R32 500 7803-3591-01
54
34 38 9
74
L

Shank adapters
Secoma

hole (mm)
(mm)
Secoma Hydrastar 200
TU,BO R32 351 7803-4703-01
54
34 45
90 9
L
Secoma Hydrastar 200, 300 and X2

TU R32 485 7803-3590-03
54 TU R38 485 7804-3590-03
TU T38 485 7304-3590-03
34 38 9
74
L
Secoma Hydrastar 350

BE R32 500 7803-3591-01
54 TU R38 485 7804-3590-03
34 38 BE T38 500 7304-3591-01
9
74
Secoma
L

Shank adapters
Toyo

hole (mm)
(mm)
Toyo PR 220
BE 14 R32 330 7803-7500-61
BE 14 T38 446 7304-7500-60
55,5
44,5 64 44,5 18,2

L
Toyo TH 501
BE 11 T38 565 7304-7583-40
64,2
44 45
68 13
L
Toyo

Auxiliary tools
Auxiliary tools
Page
Bit adapters....................................................................................79
Reduction couplings......................................................................79
Wrenches.......................................................................................80
Knock-off tools / fishing tools......................................................80
Thread grease and gauges.............................................................81
Drill steel straightener...................................................................81

Auxiliary tools
Bit adapters Wrench flat Threads

F M
Dimensions
L L D D
Part No.
(mm) (Female) (Male) (mm) (in) (mm) (in)
28,5 R23 R32 200 7 7/8 35 1 3/8 7837-3301
38 R25 R32 173 6 13/16 45 1 3/4 7832-3301
F D M
L 38 R28 R32 230 9 1/16 40 1 37/64 7839-3301
38 R32 T38 225 8 55/64 45 1 49/64 7833-4401

38 R32 R38 225 8 55/64 45 1 49/64 7833-4301
38 T35 T38 250 9 27/32 48 1 7/8 7337-4401
44,5 R38 R32 270 10 41/64 55 2 5/32 7834-3303

44,5 R38 T38 245 9 21/32 55 2 5/32 7834-4401
44,5 T38 R32 270 10 41/64 57 2 1/4" 7334-3301

44,5 T38 T45 285 11 7/32" 57 2 1/4" 7334-5401
44,5 T38 R38 280 11 1/32 57 2 1/4 7334-4301
38 T45 T38 265 10 7/16" 63 2 31/64" 7335-4401

44,5 T45 T51 285 11 7/32" 63 2 31/64" 7335-6401
Auxiliary tools
44,5 T51 T45 285 11 7/32" 71 2 51/64" 7336-5401
Reduction couplings Threads

F1 F2
Dimensions
L L D D
Part No.
(mm) (in) (mm) (in)
R32 R28 165 6 1/2 44 1 47/64 7993-0444

R32 R25 160 6 1/4 43 1 11/16 7993-2443
D
R38 R32 170 6 3/4 55 2 5/32 7994-3455
F1 F2
L
T38 R32 195 7 11/16 55 2 5/32 7314-3555
T38 R38 185 7 9/32 55 2 5/32 7314-4455
T38 T45 200 7 7/8 58 2 9/32" 7314-6258
T38 T45 220 8 43/64 61 2 13/32 7314-6261
T51 T45 218 8 19/32 71 2 51/64 7316-6271

Auxiliary tools
Wrenches and knock-off tools Dimensions

L L L D D
Part No.
(mm) (ft) (in) (mm) (in)

For integral drill steels and shank rods
Hex 22 600 1 11 5/8 22 7/8 795-1408
D
L
For extension rods
Hex 25, Round 32 300 - 11 13/16 25 1 795-1431
D Hex 32, Round 39 370 1 2 9/16 32 1 1/4 795-1432
Round 46 370 1 2 9/16 38 1 1/2 795-1494
DTH 380 1 2 31/32 65 2 7/12 795-1495
L
Knock-off-tools for Hex 22 and Hex 25

Pilot rods, type 7922-XXXX-XX - - - - - 795-1469
Knock-off-tools for tapered bits

Hex 22 - - - - - 795-1467
Auxiliary tools
Fishing tools Dimensions (mm)

D D1 L Thread
Part No.
Fishing sleeve
R32 round/Hex. rods/coupling sleeves 49 47,2 300 R32 795-1604A
R38 round rods/coupling sleeves 60 353 R38 795-1605
D D1
T35 round rods/coupling sleeves 52 50 284 T35 795-1613
T38 round rods/coupling sleeves/MF-rods 61 58,2 353 T38 795-1607A
L T45 round rods/coupling sleeves/MF-rods 71 68 393 T45 795-1608
T51 round rods/coupling sleeves/MF-rods 82 78,2 440 T51 795-1609A
GT60 rods 92 87,5 450 GT60 795-2601
GT60 rods 89 84.5 450 GT60 795-2603
ST68 tubes 87 102 92 410 ST68 795-1696
Fishing pike
D D1
R32 rods 1) 19.4 4 280 R32 795-1606
T38 rods 2) 19.4 8 237 T38 795-1676
T45 rods 2) 25 8 275 T45 795-1681
T51 rods 2) 27 15 285 T51 795-1690
L
ST58 tubes 76 2) 57 24 500 ST58 795-1699
ST68 tubes 87 2) 71 32 541 ST68 795-2600
1) Without flushing hole
2) With flushing hole

Auxiliary tools
Thread grease Dimensions

D L Weight
Part No.
(mm) (mm) (kg)

Thread grease
Can 215 170 4,5 795-1960
Can 300 380 18 795-1961
Tube 53/57 235 0,4 795-1962
Low temp. Can 300 380 18 795-1963
Barrel 370 690 50 795-1967
Barrel 610 870 240 795-1964
Gauges Thread / Hex Part No.
Gauges / Wear gauge for male and female threads

R22 795-1331
R25 795-1332
R28 795-1367
R32 795-1333
R38 795-1334
Gauges / Chuck wear gauge
Auxiliary tools
Hex 19 795-2301-19
Hex 22 795-2301-22
Hex 25 795-2301-25
Drill steel straightener Prod. Info Part No.
Drill steel straightener for Hex19 to Round 52

Manual/Hydraulic 796-2930
Electric/Hydraulic, 380V/50Hz 796-2930-52
Support leg, 1 piece 796-2931

Information
Small hole drilling tools
Third figure group
Integral steels with reduced width of bit (small gauge steel) . .................................... xxx-xxxx-50
Integral steels with reduced width of bit, + tolerance (small gauge steel) ............. xxx-xxxx-5005
Integral steels, Premium plus, H22, insert height 19 mm ........................................ xxx-xxxx-65
Shank rod, drilled for flushing tube 4.5-5 mm, packing............................................. xxxx-xxxx-13
Shank rod, drilled for flushing tube < 7 mm, no packing.......................................... xxxx-xxxx-11
Tapered rod, drilled for flushing tube < 7 mm, carburized ..................................... xxxx-6xxx-11
Tapered rod, drilled for flushing tube < 7 mm, HF- hardened ............................... xxxx-11xx-11
Cross bit, cemented carbide grade 42 ..................................................................... xxxx-xxxx-42
Tapered button bits, cemented carbide grade XT48 with ballistic buttons . ......... xxxx-xxxx-B48
Drifting and tunneling tools

Third figure group
Cross bits, cemented carbide grade 42 .................................................................... xxxx-xxxx-42
Button bits, cemented carbide grade XT48 with spherical buttons........................ xxxx-xxxx-S48
Button bits, cemented carbide grade XT48 with ballistic buttons........................... xxxx-xxxx-R48
Button bits, cemented carbide grade DP 65 with spherical buttons....................... xxxx-xxxx-S65
Button bits, one extra hole for side flushing.............................................................. xxxx-xxxxA-xxx
Rods, carburized................................................................................................... xxxx-xxxx-20
Bench drilling tools

Third figure group
Information
Insert bits, cemented carbide grade 11..................................................................... xxxx-xxxx-11

Button bits, cemented carbide grade XT48, with spherical buttons....................... xxxx-xxxx-S48
Button bits, cemented carbide grade XT48, with ballistic buttons.......................... xxxx-xxxx-R48
Button bits, cemented carbide grade DP 65, with spherical buttons . ................... xxxx-xxxx-S65
Extension rod, Guide tube, carburized .................................................................... xxxx-xxxx-20

Extension rod, HF- hardened ................................................................................... xxxx-xxxx-30
MF-rod, for surface drilling......................................................................................... xxxx-xxxx-70

Information
Long hole drilling tools
Third figure group

Button bits, cemented carbide grade XT48, with spherical buttons....................... xxxx-xxxx-S48
Button bits, cemented carbide grade XT48, with ballistic buttons.......................... xxxx-xxxx-R48
Button bits, cemented carbide grade DP 65, with spherical buttons . ................... xxxx-xxxx-S65
Button bits, cemented carbide grade DP 65, with ballistic buttons ....................... xxxx-xxxx-R65
Extension rod, carburized ......................................................................................... xxxx-xxxx-20
Drill tube, carburized . ............................................................................................... xxxx-xxxx-26

Drill tube, carburized, with permanent back flow valve . ........................................ xxxx-xxxx-46
MF-rod, carburized .................................................................................................... xxxx-xxxx-20
Bit classification code
H: Very hard to hard rock................ > 2500 bar (250 MPa)
Information
M: Medium hard rock........................ 1500-2500 bar (150-250 MPa)
S: Soft rock....................................... < 1500 bar (150 MPa)
C: Homogeneous (competent) rock

F: Fissured rock
V: Very abrasive rock....................... > 40% silica

A: Abrasive rock............................... 20-40% silica
N: Non-abrasive rock....................... 0-20% silica

Information
Grinding of Cemented Carbide
Grinding or heating a cemented carbide product will produce dust or fumes of hazardous ingredients
which can be inhaled, swallowed or come in contact with the skin or eyes.
The limiting ingredient in cemented carbide is, from a health and safety point of view, Cobalt. Another
hazardous ingredient is Tungsten Carbide.
Cobalt is classified as harmful - may cause sensitization by inhalation or skin contact. Inhalation or skin
contact may also cause irritation.
Sensitive persons may experience an allergic reaction. Repeated inhalation of aerosols containing
Cobalt may cause obstruction in the respiratory organs. Long term inhalation of increased
concentrations may cause permanent disease.
Precautions
Avoid formation and inhalation of dust.

Wet grinding is recommended instead of dry grinding.
Always use Exhaust Ventilation which is adequate to limit personal exposure well
below the Occupational Exposure Limits.
Use Respiratory Protection if ventilation is not available or adequate.
Use Safety Goggles when necessary.
Wear suitable Gloves and Protective Clothing.
Information
84 top hammer drilling tools top hammer drilling tools 84

Numerical index with weight table
Part No. Weight (kg) Page Part No. Weight (kg) Page Part No. Weight (kg) Page
714-0434-65 1,8 6 724-1226 3,0 5 7305-3591-01 5,1 68, 69

714-0635-65 2,4 6 724-1627 3,9 5 7305-3593-01 5,8 68, 69
714-0641-65 2,5 6 724-2426 5,7 5 7305-3655-01 6,4 70
714-0829 3,0 6 728-0424 1,4 5 7305-3667-01 4,5 68
714-0833-65 3,0 6 728-0429 1,4 5 7305-3690-02 6,9 70
714-0834-65 3,0 6 728-0828 2,3 5 7305-3826-02 10,3 70
714-0840-65 3,0 6 728-1627 3,9 5 7305-4791-01 6,3 71
714-1232-65 4,2 6 7305-6008-01 8,9 65
714-1234-65 4,2 6 7304-3550-01 5,4 69 7305-6010-01 9,7 65
714-1240-65 4,2 6 7304-3590-03 4,1 68, 69, 75 7305-7400-01 9,1 64
714-1628-50 5,4 6 7304-3591-01 4,8 68, 69, 75 7305-7414-01 8,9 71
714-1631 5,4 6 7304-3593-01 4,7 68, 69 7305-7417-01 9,5 71
714-1633-65 5,4 6 7304-3652-01 3,8 69 7305-7520-01 5,6 73
714-1639-65 5,4 6 7304-3655-01 0,0 70 7305-7525-19 5,5 72
714-1833-65 6,0 6 7304-3656-01 4,4 69 7305-7526-80 6,6 71
714-1839-65 6,0 6 7304-3666-01 3,9 68 7305-7532-01 6,3 64
714-2030 6,6 6 7304-3690-02 6,7 70 7305-7537-01 5,8 64
714-2033-65 6,6 6 7304-3825-02 9,9 70 7305-7541-02 6,9 64
714-2427-50 7,9 6 7304-4200-30 3,0 67 7305-7546-19 7,8 72
714-2432-65 7,9 6 7304-4500-60 2,8 67 7305-7551-01 7,6 64
714-2438-65 7,9 6 7304-4700-01 4,0 62 7305-7557-01 5,9 63
714-3231 10,3 6 7304-4700-50 3,3 62 7305-7559-19 6,1 72
714-3237-65 10,2 6 7304-4706-01 4,7 62 7305-7576-01 7,2 64
714-4030 12,7 6 7304-4720-01 3,8 73 7305-7577-02 8,5 64
714-4036-65 12,7 6 7304-4723-01 4,1 73 7305-7586-01 6,2 63
714-4829 15,2 6 7304-4780-01 6,3 71
714-4835-65 15,1 6 7304-4791-01 6,0 71 7306-3655-02 6,8 70
714-5628-50 17,6 6 7304-4993-01 5,5 70 7306-3689-01 11,0 70
714-5634-65 17,6 6 7304-7426-01 6,3 71 7306-3690-03 7,2 70
714-6427-50 20,1 6 7304-7500-60 4,0 71, 72, 76 7306-3692-01 9,5 70
714-6433-65 20,1 6 7304-7502-60 5,4 67, 73 7306-6008-01 9,3 65
714-7226-50 22,5 6 7304-7525-19 5,4 72 7306-6010-02 10,1 65
714-7232-65 22,5 6 7304-7526-80 6,3 71 7306-6014-02 11,9 65
714-8026-50 24,7 6 7304-7531-01 3,9 63 7306-6019-02 13,9 65
714-8825-5005 27,0 6 7304-7532-01 5,9 64 7306-6021-02 11,2 66
714-9625-5005 29,5 6 7304-7535-02 4,6 62 7306-6022-02 13,3 66
7304-7536-01 4,3 63 7306-6025-02 15,9 65
Index
721-1517 0,6 11 7304-7537-01 5,5 64 7306-7528-02 8,6 73

721-1620 0,7 11 7304-7541-02 6,6 64 7306-7530-02 16,1 73
721-1622 0,7 11 7304-7543-60 3,6 71, 72 7306-7551-02 8,1 64
721-1922 0,8 11 7304-7544-01 7,3 73 7306-7577-03 8,6 64
721-2020 0,8 11 7304-7554-01 5,3 63
721-2420 0,8 11 7304-7557-01 5,6 63 7307-3576-01 5,1 67
721-2820 0,9 11 7304-7576-01 6,9 64 7307-3593-01 4,5 69
721-3120 1,0 11 7304-7577-02 8,4 64 7307-3652-01 3,7 69
724-0424 1,3 5 7304-7581-60 5,2 71 7307-3656-01 4,2 69
724-0429 1,3 5 7304-7583-40 5,8 76 7307-3668-01 4,4 68
724-0627 1,7 5 7304-7585-01 5,3 63 7307-3671-01 4,9 68
724-0823 2,1 5 7304-7586-01 5,9 63 7307-3690-01 6,9 70
724-0828 2,2 5 7304-7664-01 6,4 63 7307-7535-02 4,4 62

7307-7557-01 5,6 63 7324-9661-20 44,0 23 7514-1664-R48 1,7 36, 50

7307-7566-01 4,9 63 7514-1664-S48 1,7 36, 50
7307-7585-01 5,3 63 7325-7331C-30 32,9 39 7514-1864-R48 1,7 36, 50
7307-7586-01 5,6 63 7325-7337C-30 40,0 39 7514-1870-S48 1,9 36, 50
7325-7343C-30 47,0 39 7514-1876-R48 2,3 36, 50
7314-3355 1,9 37 7325-7715C-20 17,6 53 7514-1876-S48 2,2 36, 50
7314-3555 2,3 79 7325-7718C-20 21,0 53 7514-1889-S48 3,0 36
7314-3652 1,5 23, 26, 27 7325-7731-70 35,0 39 7514-4064-11 2,0 36
7314-4455 1,9 79 7325-7737-70 41,2 39 7514-4076A-11 2,6 36
7314-6258 2,0 79,0 7325-7743-70 47,5 39 7514-4664-R48 2,0 36, 50
7314-6261 2,8 79 7325-7761-70 70,0 39 7514-4664-S48 2,2 36, 50
7326-5337C-30 50,0 41 7514-4864-R48 2,2 36, 50
7315-3663 2,7 39 7326-5343C-30 56,0 41 7514-4870-S48 2,4 36, 50
7316-3671 3,7 41 7326-5361C-30 85,0 41 7514-4876-R48 2,9 36, 50
7316-3676 4,6 41 7326-5515C-20 23,0 55 7514-4876-S48 3,5 36, 50
7316-6271 4,0 79 7326-5518C-20 27,0 55 7514-8264-R48 2,0 36, 50
7326-5537-70 50,5 41
7324-4131-20 25,0 25 7326-5543-70 56,5 41 7515-1870-S48 2,3 38, 52
7324-4137-20 29,4 25 7326-5561-70 87,0 41 7515-1876-R48 2,5 38, 52
7324-4143-20 33,8 25 7327-4718-20 16,1 49 7515-1876-S48 2,5 38, 52
7324-4149-20 39,2 25 7327-4731-20 25,4 29 7515-1889-R48 3,1 38, 52
7324-4155-20 44,0 25 7327-4737-20 32,0 29 7515-1889-S48 3,2 38, 52
7324-4249-20 44,0 25 7327-4743-20 35,0 29 7515-1902-R48 4,0 38
7324-4255-20 48,0 25 7327-4749-20 40,1 29 7515-1902-S48 4,0 38
7324-4261-20 57,0 25 7327-5243-20 35,0 29 7515-4870-R48 2,7 38, 52
7324-4264-20 57,0 25 7327-5249-20 40,1 29 7515-4876-R48 3,2 38, 52
7324-4331C-30 24,1 37 7327-5255-20 45,0 29 7515-4876-S48 3,3 38, 52
7324-4337C-30 29,0 37 7327-5261-20 50,0 29 7515-4889-R48 4,8 38, 52
7324-4712C-20 10,6 51 7328-6009-02 17,4 65 7515-4889-S48 4,8 38, 52
7324-4715C-20 13,3 51 7328-6020-01 17,0 66 7515-4902-R48 5,9 38
7324-4718C-20 16,1 51 7328-6035-01 22,0 66 7515-4902-S48 6,8 38
7324-4731-70 25,5 37 7329-3716-01 21,3 70 7515-5627-S45 6,8 52
7324-4737-70 30,0 37 7329-3720-01 26,9 70 7515-5652-S45 9,0 52
7324-4743-70 36,4 37 7329-6009-02 16,9 65 7515-8276-R48 3,2 38, 52
7324-6931-20 18,3 37 7329-6020-01 16,8 66 7515-8289-R48 4,8 38, 52
7324-7243-20 35,0 27 7329-6035-01 22,4 66
7324-7249-20 39,9 27 7334-3301 2,6 79 7516-1889-R48 3,6 40, 54
Index
7324-7255-20 44,8 27 7334-4301 3,3 79 7516-1889-S48 3,6 40, 54

7324-7261-20 49,3 27 7334-5401 3,3 79 7516-1902-R48 4,6 40, 54
7324-8543-20 33,7 27 7335-4401 2,9 79 7516-1902-S48 4,4 40, 54
7324-8549-20 37,1 27 7335-6401 3,7 79 7516-1915-S48 6,0 40
7324-8555-20 42,0 27 7336-5401 3,8 79 7516-1927-S48 6,6 40
7324-8561-20 46,1 27 7337-4401 1,9 79 7516-4889-R48 4,2 40, 54
7324-8637-20 25,5 23 7378-7615-26 33,2 57 7516-4889-S48 4,4 40, 54
7324-8643-20 27,5 23 7378-7618-26 41,0 57 7516-4902-R48 6,3 40, 54
7324-9631-20 24,0 23 7379-8715-26 40,0 58 7516-4902-S48 6,1 40, 54
7324-9637-20 27,5 23 7379-8715-46 40,0 58 7516-4915-R48 8,4 40
7324-9643-20 32,0 23 7379-8718-26 47,0 58 7516-4915-S48 8,1 40
7324-9649-20 37,0 23 7379-8718-46 52,0 58 7516-4927-S48 10,2 40
7324-9655-20 42,2 23 7516-5652-S45 9,3 54

7517-1654A-S48 1,0 35, 49 7721-4802-S45 2,0 24, 26, 28 7738-5348A-S48 0,9 27

7517-4654-R48 1,3 35, 49 7721-4827-S45 3,6 24, 26, 28 7738-5602-S45 3,2 28
7517-4657-R48 1,5 35, 49 7721-4889-S45 1,5 24, 26, 28 7738-4654A1-R48 1,3 29
7722-4864-S45 0,9 7, 20, 21, 24 7739-1438-42 0,6 21
7525-8476-R65 3,4 56 7722-4876-S45 1,3 7, 20, 21, 24 7739-5238-R48 0,6 21
7528-5652-S65 13,0 57 7722-4889-S45 1,7 7, 20, 21, 24 7739-5238-S48 0,6 21
7528-6989-S65 4,5 57 7723-4802-S45 3,6 48, 51 7739-5241-S48 0,6 21
7528-8489-R65 4,0 57 7723-4827-S45 5,2 48, 51 7739-5243-S48 0,6 21
7529-5652C-S65 14,8 58 7731-1038-42 0,5 12 7764-5235-R48 0,4 15
7529-6652-S45 8,9 58 7732-1435-42 0,4 14, 19 7764-5238-R48 0,4 15
7529-6902-S65 5,2 58 7732-1633-42 0,4 19 7764-5345F-R48 0,8 15
7529-7302-R65 5,7 58 7732-4433C-S48 0,3 19 7766-1345A-42 0,8 25
7529-7315-R65 7,5 58 7732-4435-S48 0,4 14, 19 7766-1651A-R48 0,9 25
7529-8402-R65 5,2 58 7732-5237-S48 0,4 19 7766-1651A-S48 0,9 25
7529-8415-R65 5,9 58 7732-5238-R48 0,5 14 7766-5243A-S48 0,6 25
7732-5238-S48 0,5 14, 19 7766-5245A-S48 0,8 25
7600-6014-02 12,9 65 7732-5241-S48 0,5 14, 19 7766-5248A-S48 0,8 25
7600-6022-03 14,6 66 7732-5345F-R48 0,8 14 7766-5345A-R48 0,8 25
7600-6025-02 16,7 65 7733-1345A-42 0,8 22 7766-5345A-S48 0,8 25
7600-6030-01 20,5 66 7733-1451-42 1,0 33, 47 7766-5348A-R48 0,9 25
7600-6031-01 20,8 65 7733-1651A-R48 0,9 22, 33, 47 7766-5348A-S48 0,9 25
7600-6032-01 23,5 66 7733-1651A-S48 0,9 22, 33, 47 7766-5443B-R48 0,6 25
7600-7530-02 16,9 73 7733-1657A-S48 1,1 33, 47 7766-5445B-R48 0,8 25
7610-1137-70 73,0 43 7733-1664-S48 1,6 33, 47 7766-5602P-S48 3,2 26
7610-1143-70 82,0 43 7733-4651-R48 1,1 33, 47 7770-5233-B48 0,3 8
7610-1161-70 110,0 43 7733-4651-S48 1,1 33, 47 7770-5235-B48 0,3 8
7610-1243-70 92,0 43 7733-4664-S48 2,1 33, 47 7770-9030-42 0,3 8
7610-1443-70 85,0 43 7733-5243A-S48 0,7 22 7770-9032-42 0,3 8
7620-1892-S48 5,2 42 7733-5245A-S48 0,8 22 7770-9035-42 0,4 8
7620-1896-S48 5,3 42 7733-5248A-S48 0,9 22 7776-1932-B48 0,2 9
7620-1902-S48 6,4 42 7733-5251A-S48 1,0 22 7776-1936-B48 0,2 9
7620-1915-R48 7,3 42 7733-5345A-R48 0,8 22 7776-1938-B48 0,2 9
7620-1915-S48 7,8 42 7733-5345A-S48 0,8 22 7776-1940-B48 0,3 9
7620-1927-S48 8,9 42 7733-5348A-R48 0,9 22 7776-4432-B48 0,3 9
7620-1940-S48 12,1 42 7733-5348A-S48 0,9 22 7776-4435-B48 0,3 9
7620-1952-S48 13,8 42 7733-5443B-R48 0,7 22 7776-4438-B48 0,3 9
7620-4902-R48 7,6 42 7733-5445B-R48 0,8 22 7776-4440-B48 0,3 9
Index
7620-4902-S48 7,6 42 7733-5602-S45 3,2 24 7788-5232-B48 0,3 10

7620-4915-R48 9,4 42 7733-5745A-C48 0,8 22 7788-5233-B48 0,3 10
7620-4915-S48 9,6 42 7733-8251-R48 1,3 33, 47 7788-5235-B48 0,3 10
7620-4927-S48 13,1 42 7737-4433-R48 0,3 13 7788-5238-B48 0,4 10
7620-4940-S48 16,1 42 7737-4438A-R48 0,4 13 7795-5232-B48 0,2 8
7620-4952-S48 18,9 42 7737-5235-R48 0,3 13 7795-5235-B48 0,3 8
7620-8115-S48 9,9 42 7737-5241-R48 0,4 13 7795-5238-B48 0,3 8
7620-8702-R48 8,0 42 7737-5345-R48 0,5 13 7795-6428-B48 0,2 8
7620-8792-R48 6,1 42 7738-1448-42 1,0 27 7795-6430-B48 0,2 8
7620-8796-R48 6,2 42 7738-1651A-R48 1,0 27
7640-7653-70 111,5 43 7738-1651A-S48 1,0 27 7801-6103-13 1,1 12, 61
7640-8743-70 106,0 43 7738-5248-S48 0,9 27 7801-6110-13 3,4 12
7660-8743-71 103,6 43 7738-5348A-R48 0,9 27 7802-6103-13 1,1 14, 61

7802-6108-13 3,0 14 7807-6103-11 1,2 13, 61 7853-5131-20 17,7 34

7802-6110-13 3,5 14 7807-6124-11 7,7 13 7853-5137-20 21,7 34
7802-7103-14 1,4 61 7807-6132-11 11,5 13 7853-7631-20 15,0 21
7802-7503-20 1,6 61 7807-6136-11 12,5 13 7853-7637-20 20,0 21
7802-7567-01 1,0 63 7807-7103-11 1,3 13, 61 7853-7643-20 21,0 21,0
7803-3100-30 2,0 67 7807-7136-11 18,1 13 7854-8631-20 20,0 23,0
7803-3576-01 4,8 68, 74 7807-7570-01 1,0 63 7854-8637-20 23,5 23
7803-3583-01 3,0 69 7809-7547-01 2,7 62 7854-8643-20 27,0 23
7803-3588-01 3,3 67, 74 7814-7136-11 18,1 15 7854-8649-20 30,5 23
7803-3590-03 3,9 68, 75 7821-3040 2,7 26 7854-9631-20 23,1 23
7803-3591-01 4,1 68, 69, 74, 75 7821-3440 2,8 24 7854-9637-20 27,8 23
7803-3593-01 4,6 68, 69 7821-5440 2,7 28 7854-9643-20 32,8 23
7803-3602-30 2,1 62 7822-1526 1,9 21 7854-9649-20 37,0 23
7803-3652-01 3,7 69 7822-2526 1,3 20 7857-4821-20 6,4 13
7803-3656-01 4,1 69 7822-3526 1,5 24 7857-4831-20 10,0 13
7803-3670-02 4,7 69 7823-2647 4,6 51 7870-1140-11 17,1 8
7803-4200-30 2,6 67 7823-3647 4,4 48 7870-1144-11 13,9 8
7803-4700-01 3,7 62 7832-3301 1,2 79 7870-1148-11 14,8 8
7803-4700-50 2,7 62 7833-4301 1,8 79 7870-1156-11 17,5 8
7803-4703-01 3,6 75 7833-4401 1,9 79 7870-1164-11 19,8 8
7803-4725-01 3,3 73 7834-3303 2,5 79 7870-1172-11 22,5 8
7803-4726-01 2,8 73 7834-4401 2,3 79 7870-1180-11 25,0 8
7803-7500-61 3,0 71, 72, 76 7837-3301 1,0 79 7870-1188-11 27,0 8
7803-7531-01 3,8 63 7839-3301 1,4 79 7870-5124-11 7,9 8
7803-7532-01 5,7 64 7851-1308-20 2,3 12 7870-5132-11 10,2 8
7803-7535-02 4,2 62 7851-1312-20 3,6 12 7870-6106-11 2,3 8
7803-7543-60 4,1 72 7851-1316-20 4,8 12 7870-6112-11 4,1 8
7803-7547-01 2,5 62 7852-2309-20 3,6 14 7870-6118-11 6,0 8
7803-7549-01 2,6 62 7852-2312-20 4,6 14 7870-6120-11 6,5 8
7803-7553-01 3,9 63 7852-2315-20 5,7 14 7870-6124-11 5,9 8
7803-7557-01 5,6 63 7852-2318-20 6,9 14 7870-6131-11 9,8 8
7803-7585-01 5,1 63 7852-2324-20 9,0 14 7870-6132-11 10,2 8
7803-7586-01 5,4 63 7852-2331-20 11,5 14 7870-6137-11 11,4 8
7803-7664-01 5,7 63 7853-2418-20 8,5 19 7876-6106-11 2,2 9
7804-3575-01 4,1 67, 74 7853-2421-20 10,2 19 7876-6108-11 2,7 9
7804-3590-03 4,2 68, 69, 75, 75 7853-2424-20 10,0 19 7876-6112-11 4,1 9
7804-3652-01 3,8 69 7853-2426-20 12,5 19 7876-6118-11 5,9 9
Index
7804-3670-02 4,3 69 7853-2427-20 14,0 19 7876-6120-11 7,8 9

7804-4700-01 3,9 62 7853-2429-20 16,1 19 7876-6124-11 7,8 9
7804-4720-01 3,9 73 7853-2431-20 11,5 19 7876-6131-11 9,6 9
7804-4725-01 3,8 73 7853-3309-20 5,8 48 7876-6136-11 11,0 9
7804-4993-01 5,5 70 7853-3312-20 6,3 48 7888-6124-11 8,0 10
7804-7500-60 3,5 72 7853-3315-20 8,0 48 7888-6132-11 8,3 10
7804-7531-01 4,2 63 7853-3318-20 9,8 48
7804-7535-02 4,5 62 7853-3331-30 16,4 34 7922-6108-11 3,3 7
7804-7536-01 4,4 63 7853-3337-30 19,7 34 7922-6112-11 4,7 7
7804-7554-01 5,2 63 7853-5109-20 5,5 48 7922-6120-11 7,0 7
7804-7585-01 5,3 63 7853-5112-20 7,5 48 7922-6124-11 7,9 7
7805-6015 10,4 72 7853-5115-20 9,0 48
7805-7015 10,4 72 7853-5118-20 11,0 48 795-1331 0,2 81

795-1332 0,3 81
795-1333 0,4 81
795-1334 0,4 81
795-1367 0,3 81
795-1408 3,1 80
795-1431 3,5 80
795-1432 3,5 80
795-1467 1,0 80
795-1469 4,4 80
795-1494 3,5 80
795-1495 5,2 80
795-1604A 1,9 80
795-1605 3,9 80
795-1606 0,6 80
795-1607A 3,9 80
795-1608 6,0 80
795-1609A 8,4 80
795-1613 1,7 80
795-1676 0,9 80
795-1681 1,5 80
795-1690 2,0 80
795-1696 10,9 80
795-1699 4,9 80
795-1960 4,9 81
795-1961 18,0 81
795-1962 0,6 81
795-1963 18,0 81
795-1964 240,0 81
795-1967 50,0 81
795-2301-19 0,0 81
795-2301-22 0,0 81
795-2301-25 0,0 81
795-2600 7,9 80
795-2601 10,2 80
795-2603 9,9 80
7953-4618-20 16,0 48
Index
7953-4631-20 24,0 34
7955-5618-20 24,0 51
7955-5637-20 48,0 37
7956-6318-21 28,0 53
7956-6337-70 46,0 39
7956-7637-70 77,5 39
7957-7618-20 40,0 55
7957-7637-70 76,0 41
7957-8737-70 89,0 41
796-2930 50,0 81
796-2930-52 60,0 81
796-2931 5,0 81

Notes
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
Notes
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................

Notes
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
Notes
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................

Notes
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................
Notes
................................................................................................................................................................................................
................................................................................................................................................................................................
................................................................................................................................................................................................

Top hammer drilling tools
Product catalogue
Roc k d r illin g tools

Products from Sandvik Mining and Construction Tools
Top h a m m er p ro d uc t s
www.sandvik.com

SE-811 81 Sandviken, Sweden. Tel +46 26 26 20 00 Fax +46 26 26 23 00
HR-12281-ENG AB Sandvikens Tryckeri

Catalogo Tophammer PDF

Uploaded by

Copyright:

Available Formats

Catalogo Tophammer PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalogo Tophammer PDF

Uploaded by

Copyright:

Available Formats

Top hammer drilling tools

Roc k d r illin g tools

Sandvik Mining and Construction Tools AB

HR-12281-ENG AB Sandvikens Tryckeri

Small hole drilling 3

Drifting and tunneling 17

Long hole drilling 45

Sandvik Mining and Construction Tools AB

Concerning bit diameters

Cross bits: Can be max 1 mm larger due to manufacturing tolerances.

Bit classification code

H: Very hard to hard rock................ > 2500 bar (250 MPa)

C: Homogeneous (competent) rock

V: Very abrasive rock....................... > 40% silica

H19 (3/4) Integral drill steels...........................................................5

H22 (7/8") Integral drill steels.........................................................6

H22 Tapered tools, 12 taper..........................................................8

H22 Tapered tools, 11 taper...........................................................9

H22 Tapered tools, 7 taper..........................................................10

Stone working tools........................................................................11

R22 (7/8") Extension drilling tools................................................12

R23 (29/32") Extension drilling tools............................................13

R25 (1") Extension drilling tools.....................................................14

Sandvik Alpha. 250 bit thread .....................................................15

4 top hammer drilling tools

Dimensions D Part No.

24 600 2' 27 1 1/16" 724-0627

Boulder- 400 1' 4" 24 15/16" 724-0424

Shank 22 x 108 mm (7/8 x 4 1/4)

top hammer drilling tools 5

Dimensions D Part No.

12 800 2' 7" 40 1 37/64" 714-0840-65

13 400 1' 4" 34 1 11/32" 714-0434-65

16 600 2' 35 1 3/8" 714-0635-65

17 600 2' 41 1 5/8" 714-0641-65

2000 6' 7" 33 1 19/64" 714-2033-65

800 2' 7" 29 1 9/64" 714-0829

6 top hammer drilling tools

Buttons, mm Angle Dimensions D Part No.

top hammer drilling tools 7

Bits Flushinghole, mm Buttons, mm Angle Dimensions D Part No.

Front Gauge Front Gauge

8 top hammer drilling tools

Bits Flushinghole, mm Buttons, mm Angle Dimensions D Part No.

top hammer drilling tools 9

Bits Flushinghole, mm Buttons, mm Angle Dimensions D Part No.

Front Gauge Front Gauge

10 top hammer drilling tools

top hammer drilling tools 11

Cross bit Flushinghole, mm

No Size No Size No Size No Size mm in

Dimensions D Part No.

Shank adapter/Shank rod, Hex 22 - R22

Coupling sleeve, R22

12 top hammer drilling tools

Shank rod, Hex 25 - R23

top hammer drilling tools 13

Bits Flushinghole, mm Buttons, mm Angle Dimensions D Bit Part No.

Extension rod, R25 - Hex 25 - R25