Setup, Operator, and Service Guide: Ibm Totalstorage 3581 Tape Autoloader Models L28/L38/L3H and F28/F38/F3H
Setup, Operator, and Service Guide: Ibm Totalstorage 3581 Tape Autoloader Models L28/L38/L3H and F28/F38/F3H
Setup, Operator, and Service Guide: Ibm Totalstorage 3581 Tape Autoloader Models L28/L38/L3H and F28/F38/F3H
GA32-0470-01
GA32-0470-01
Note! Before using this information and the product it supports, read the information in Safety and Environmental Notices on page xv and Notices on page 293. To ensure that you have the latest publications, visit the web at http://www.ibm.com/storage/support/lto, select your product, and click Documentation.
| This edition applies to the IBM TotalStorage Ultrium Tape Autoloader 3581 Models L28/L38/L3H and F28/F38/F3H Setup, | Operator, and Service Guide and to all subsequent releases and modifications until otherwise indicated in new | editions. | The IBM TotalStorage Ultrium Tape Autoloader 3581 Models L28/L38/L3H and F28/F38/F3H offer a 3-year | parts-only warranty and are supported by the Customer Replaceable Unit (CRU) process. For details about the CRU | process and customer responsibilities, see the warranty that is included in the back of this document.
Copyright International Business Machines Corporation 2004, 2005. All rights reserved. US Government Users Restricted Rights Use, duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.
Summary of Changes
This section summarizes changes to this publication. A vertical line in the left margin indicates each change.
iii
iv
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Contents
Read This First . . . . . . . . . . . iii
| |
Accessing Online Technical Support Summary of Changes . . . . . Second Edition (March 2005) . . Registering for My Support . . . Sending IBM Your Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii iii iii iii iii Server (Host) Attachment . . . . . . . Supported Servers (Hosts) and Operating Systems . . . . . . . . . . . Supported Device Drivers . . . . . TapeAlert Support . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . 14 . . . . 14 15 15 15
Installation . . . . . . . . . . . . . 17
Step 1. Unpack the Autoloader . . . . . . . Step 2. Verify the Shipment Inventory . . . . Step 3. Inspect the Power Cord and Outlet . . . Step 4. Install the Optional Remote Management Unit (RMU) . . . . . . . . . . . . . Tools Required . . . . . . . . . . . Installing the RMU . . . . . . . . . . Step 5. Install the Optional HVD Converter (L28 Models Only) . . . . . . . . . . . . . Tools Required . . . . . . . . . . . Installing the HVD Converter . . . . . . Step 6. Install the Optional Bar Code Reader (BCR) Tools Required . . . . . . . . . . . Installing the BCR . . . . . . . . . . Step 7. Install the Autoloader as a Desktop Unit . Step 8. Install the Autoloader in a Rack . . . . Rack Safety . . . . . . . . . . . . Tools Required . . . . . . . . . . . Verify the Rack Mount Kit . . . . . . . Check the Installation Environment . . . . Prepare the Autoloader for Installation . . . Install the Support Rails in the Rack . . . . Install the Rack Front-Mount Brackets on the Autoloader . . . . . . . . . . . . Secure the Autoloader to the Rack . . . . . Step 9. Connect Power . . . . . . . . . . Desktop Installation . . . . . . . . . Rack Installation . . . . . . . . . . . Running a Drive Recalibration Test . . . . LIBRARY VERIFY Test. . . . . . . . . Step 10. Connect the Autoloader to Your Server (Host) . . . . . . . . . . . . . . . RMU Cabling . . . . . . . . . . . . SCSI Interface . . . . . . . . . . . Fibre Channel Interface . . . . . . . . Step 11. Power on the Autoloader . . . . . . Configuring Your Autoloader . . . . . . . Saving / Restoring VPD on the RMU. . . . . 18 . 19 . 21 . 22 . 22 . 22 . 23 . 23 . 23 25 . 25 . 25 . 26 . 27 . 27 . 28 . 28 . 30 . 31 . 31 . . . . . . . . . . . . . . 33 34 36 36 36 37 37 38 38 38 39 41 41 41
| | | | |
| |
| | | |
| |
Information Menu . . Go Offline . . . . . Model L28/L38/L3H (SCSI Information Menu . . Commands Menu . . Configuration Menu . Diagnostic Menu . . Go Online . . . . . Model F28/F38/F3H (Fibre Menu . . . . . . . Information Menu . . Commands Menu . . Configuration Menu . Diagnostic Menu . . Go Online . . . . .
. . . . . . . . . . . . . .
49 53 55 55 55 60 67 74 75 76 76 76 84 84
| | | | | | | | | | | | | | | | | | | | |
Configuration . . . . . . . . . . . . 85
Passwords . . . . . . . . . . . . . . . 85 OCP Password . . . . . . . . . . . . 85 RMU Passwords . . . . . . . . . . . . 86 Serial Communication Password . . . . . . 86 Configuring a Model L28/L38/L3H Autoloader . . 91 Step 1. Go Offline Using the OCP . . . . . . 91 Step 2. Change SCSI ID . . . . . . . . . 91 Step 3. Change SCSI Speed . . . . . . . . 92 Step 4. Change the Operating Mode . . . . . 92 Step 5. Configure the RMU . . . . . . . . 95 Step 6. Configure the BCR . . . . . . . . 96 Step 7. Cycle Autoloader Power . . . . . . 96 Step 8. Set Protection Mode ON or OFF . . . . 97 Step 9. Save Vital Product Data (Autoloader with RMU Only) . . . . . . . . . . . . . 97 Step 10. Update Autoloader Configuration Form 98 Configuring a Model F28/F38/F3H Autoloader . . 99 Step 1. Go Offline Using the OCP . . . . . . 99 Step 2. Change Loop ID . . . . . . . . . 99 Step 3. Select Fibre Channel Port . . . . . . 100 Step 4. Enter WW Node Name . . . . . . 100 Step 5. Change Fibre Channel Speed . . . . 100 Step 6. Change the Operating Mode . . . . . 101 Step 7. Configure the RMU . . . . . . . . 103 Step 8. Configure the BCR . . . . . . . . 104 Step 9. Cycle Autoloader Power . . . . . . 104 Step 10. Set Protection Mode ON or OFF . . . 105 Step 11. Save Vital Product Data (Autoloader with RMU Only) . . . . . . . . . . . 105 Step 12. Update Autoloader Configuration Form 106 Completing Configuration of Autoloader . . . . 107 Step 1. Import Cartridges . . . . . . . . 107 Step 2. Configure RMU User Accounts . . . . 108 Step 3. Install Device Drivers . . . . . . . 110 Step 4. Configure the Autoloader to the Server (Host) . . . . . . . . . . . . . . . 110 Step 5. Update Firmware . . . . . . . . 111 Step 6. Register for My Support . . . . . . 121
| |
| | | | |
| | | | |
Quick Status . . . . . . . . . . . . . . Status Icons . . . . . . . . . . . . . Information Menu . . . . . . . . . . . . Autoloader (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Drive (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Status Menu . . . . . . . . . . . . . . Autoloader (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Media (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Configuration Menu . . . . . . . . . . . Device (Model L28/L38/L3H) . . . . . . . Device (Model F28/F38/F3H) . . . . . . . Network (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . User (Models L28/L38/L3H and F28/F38/F3H) RTC (Models L28/L38/L3H and F28/F38/F3H) Log (Models L28/L38/L3H and F28/F38/F3H) Event Notification (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Reset (Models L28/L38/L3H and F28/F38/F3H) Maintenance Menu . . . . . . . . . . . Operations (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . General Diagnostic (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Advanced Diagnostic (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . Firmware (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Reset (Models L28/L38/L3H and F28/F38/F3H) Logs Menu . . . . . . . . . . . . . . Loader (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Drive (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Logout . . . . . . . . . . . . . . .
125 125 126 126 127 128 128 129 130 130 131 132 133 134 134 135 136 137 137 138 138 139 139 140 140 141 142
Media . . . . . . . . . . . . . . . 143
Data Cartridge . . . . . . . . . . . . . Cleaning Cartridge . . . . . . . . . . . Bar Code Label . . . . . . . . . . . . . Guidelines for Using Bar Code Labels . . . . Setting the Write-Protect Switch . . . . . . . Handling Cartridges . . . . . . . . . . . Provide Training . . . . . . . . . . . Ensure Proper Packaging . . . . . . . . Provide Proper Acclimation and Environmental Conditions . . . . . . . . . . . . . Perform a Thorough Inspection . . . . . . Handle the Cartridge Carefully . . . . . . Examples of Cartridge Problems . . . . . . Environmental and Shipping Specifications for Tape Cartridges . . . . . . . . . . . . Repositioning or Reattaching a Leader Pin . . . Repositioning a Leader Pin . . . . . . . . Reattaching a Leader Pin . . . . . . . . Disposing of Tape Cartridges . . . . . . . . Ordering Media Supplies . . . . . . . . . 144 145 145 146 147 147 148 148 149 149 150 150 151 152 152 154 158 159
vi
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
. 160
| |
Before Powering OFF the Autoloader . . . Removing the Autoloader . . . . . . . Replacing the Autoloader . . . . . . . Removing/Replacing the External Fan . . . . Tools Required . . . . . . . . . . . Removing the External Fan . . . . . . . Replacing the External Fan . . . . . . . Removing/Replacing the Bar Code Reader (BCR) Tools Required . . . . . . . . . . . Removing the BCR . . . . . . . . . Replacing the BCR. . . . . . . . . . Removing/Replacing the RMU . . . . . . Tools Required . . . . . . . . . . . Removing the RMU . . . . . . . . . Replacing the RMU . . . . . . . . . Removing/Replacing the HVD Converter . . . Tools Required . . . . . . . . . . . Removing the HVD Converter . . . . . Replacing the HVD Converter . . . . . .
. . . . . . . . . . . . . . . . . .
204 204 205 208 208 208 208 210 210 210 211 212 212 212 213 214 214 214 215
Parts Lists
. . . . . . . . . . . . 217
. . . . . . . . . . . . . . . . . . . . . . 217 . 218 . 218
| |
| |
Messages . . . . . . . . . . . . . 233
Obtaining Tape Drive or Library Error Information at the Host . . . . . . . . . . . . . . Obtaining Error Information from an RS/6000 or pSeries . . . . . . . . . . . . . . . Obtaining Service Information Message from an iSeries or AS/400 . . . . . . . . . . . . iSeries or AS/400 System with RISC Processor Obtaining Error Information from a Sun System Obtaining Error Information from an HP-UX System . . . . . . . . . . . . . . . Obtaining Error Information from a Linux System Fixing Drive SCSI Bus Errors . . . . . . . . Fixing a Consistent Error with a Single Drive on a SCSI Bus . . . . . . . . . . . . . Fixing an Intermittent Error with a Single Drive on a SCSI Bus . . . . . . . . . . . . 233 233 237 237 238 238 239 239 239 240
| | |
. . . 251
vii
| | | | | | |
Recommended Tools . . . . . . . . Beginning Procedure . . . . . . . . Tape Spooled off Supply Reel . . . . . Tape Pulled from or Broken near Leader Pin Tape Broken in Mid-tape . . . . . . Tape Tangled Along Tape Path . . . . No Apparent Failure or Damage to Tape .
. . . . . .
Notices . . . . . . . . . . . . . . 293
Getting Help . . . . . . . . Trademarks . . . . . . . . . Electronic Emission Notices . . . IBM 3581 Ultrium Tape Autoloader Statement of Limited Warranty . . Part 1 - General Terms . . . . Part 2 - Country-unique Terms . Part 3 - Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 295 296 296 298 298 301 311
| | |
| | |
. 279 . 279
viii
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Figures
|
1. AC Grounding Diagram (50 Hz and 60 Hz) xviii 2. IBM TotalStorage Ultrium Tape Autoloader 3581 Models L28/L38/L3H and F28/F38/F3H . . . 3 3. Front panel components . . . . . . . . . 7 4. Interior components with one cartridge slot 8 5. Rear panel label showing power ratings and warning customers not to remove the Autoloader cover . . . . . . . . . . 10 6. Rear panel with standard elements and SCSI connectors with an LVD SCSI (Model L28lL38/L3H) drive . . . . . . . . . . 10 7. Rear panel components with an LVD SCSI drive (Model L28/L38/L3H) and HVD Converter . . . . . . . . . . . . . 11 8. Rear panel with a Fibre Channel (Model F28/F38/F3H) drive connection . . . . . . 11 9. Installing the RMU . . . . . . . . . . 22 10. Aligning the HVD Converter to the Autoloader . . . . . . . . . . . . . 23 11. Installing the HVD Converter . . . . . . 24 12. SCSI HVD Differential terminator . . . . . 24 13. Installing the Bar Code Reader . . . . . . 25 14. Illustration of parts contained in the Rack Mount Kit . . . . . . . . . . . . . 29 15. PCC cable . . . . . . . . . . . . . 30 16. EIA identification . . . . . . . . . . 31 17. Attaching cage clip-nuts to a rack with square holes . . . . . . . . . . . . . . . 32 18. Attaching expanding rails to the rack . . . . 33 19. Installing rack-mount brackets . . . . . . 34 20. Installing the Autoloader in a rack . . . . . 35 21. PCC cable . . . . . . . . . . . . . 36 22. SCSI receptacles on rear of Autoloader . . . 39 23. SCSI receptacles on HVD Converter . . . . 39 24. Fibre Channel receptacle . . . . . . . . 40 25. Operator Control Panel (OCP) . . . . . . 46 26. Operator Control Panel (OCP) Home Screen 47 27. Online menu tree . . . . . . . . . . 49 28. Information Menu LOADER INFO item 50 29. Information Menu Error Log for the Autoloader command . . . . . . . . . 51 30. Information Menu DRIVE INFO item . . . . 52 31. Information Menu SCSI Event Log for the drive command . . . . . . . . . . . 52 32. Information Menu Error Log for the drive command . . . . . . . . . . . . . 53 33. Autoloader Model L28/L38/L3H Offline Menu 55 34. Commands Menu BULK EXCHANGE command . . . . . . . . . . . . . 56 35. Commands Menu IMPORT command . . . . 56 36. Commands Menu EXPORT command . . . . 57 37. Commands Menu LOAD CARTRIDGE and UNLOAD CARTRIDGE commands . . . . 58 38. Commands Menu CLEAN DRIVE command 59 39. Commands Menu RE-INVENTORY command 60 40. Configuration Menus RESET command 60
Copyright IBM Corp. 2004, 2005
| | | | | |
| |
| | | |
| | |
41. Configuration Menus CHANGE SCSI ID command . . . . . . . . . . . . . 42. Configuration Menus SCSI SPEED command 43. Configuration Menus CHANGE LDR MODE command . . . . . . . . . . . . . 44. Configuration Menus LOOP MODE command 45. Configuration Menus AUTOLOAD MODE command . . . . . . . . . . . . . 46. Configuration Menus NET PARAMETER command . . . . . . . . . . . . . 47. Configuration Menus BARCODE READER command . . . . . . . . . . . . . 48. Configuration Menus PROTECTION MODE command . . . . . . . . . . . . . 49. Configuration Menus SERIAL NUMBER command . . . . . . . . . . . . . 50. Diagnostic Menus LOADER DIAG Library Verify command . . . . . . . . . . . 51. Diagnostic Menus LOADER DIAG System Test command . . . . . . . . . . . 52. Diagnostic Menus DRIVE DIAG menu 53. Autoloader Model F28/F38/F3H Offline Menu 54. Configuration Menus RESET command 55. Configuration Menus CHANGE LOOP ID command . . . . . . . . . . . . . 56. Configuration Menus FIBRE CHANNEL command . . . . . . . . . . . . . 57. Configuration Menus WW NODE NAME command . . . . . . . . . . . . . 58. Configuration Menus FC SPEED command 59. Configuration Menus CHANGE LDR MODE command . . . . . . . . . . . . . 60. Configuration Menus LOOP MODE command 61. Configuration Menus AUTOLOAD MODE command . . . . . . . . . . . . . 62. Configuration Menus NET PARAMETER command . . . . . . . . . . . . . 63. Configuration Menus BARCODE READER command . . . . . . . . . . . . . 64. Configuration Menus PROTECTION MODE command . . . . . . . . . . . . . 65. Configuration Menus SERIAL NUMBER command . . . . . . . . . . . . . 66. HyperTerminal Connection Description window . . . . . . . . . . . . . . 67. HyperTerminal Connect To window . . . . 68. HyperTerminal COMx Properties window 69. Configuration Menus CHANGE SCSI ID command . . . . . . . . . . . . . 70. Configuration Menus SCSI SPEED command 71. Configuration Menus CHANGE LDR MODE command . . . . . . . . . . . . . 72. Configuration Menus LOOP MODE command 73. Configuration Menus AUTOLOAD MODE command . . . . . . . . . . . . .
61 61 62 63 63 64 65 66 67 68 69 70 75 76 76 77 77 78 79 80 80 81 82 82 83 87 88 89 91 92 92 93 94
ix
| |
| |
74. Configuration Menus NET PARAMETER command . . . . . . . . . . . . . 95 75. Configuration Menus BARCODE READER command . . . . . . . . . . . . . 96 76. Configuration Menus PROTECTION MODE command . . . . . . . . . . . . . 97 77. Configuration Menus CHANGE LOOP ID command . . . . . . . . . . . . . 99 78. Configuration Menus FIBRE CHANNEL command . . . . . . . . . . . . . 100 79. Configuration Menus WW NODE NAME command . . . . . . . . . . . . . 100 80. Configuration Menus FIBRE SPEED command . . . . . . . . . . . . . 101 81. Configuration Menus CHANGE LDR MODE command . . . . . . . . . . . . . 101 82. Configuration Menus LOOP MODE command . . . . . . . . . . . . . 102 83. Configuration Menus AUTOLOAD MODE command . . . . . . . . . . . . . 102 84. Configuration Menus NET PARAMETER command . . . . . . . . . . . . . 103 85. Configuration Menus BARCODE READER command . . . . . . . . . . . . . 104 86. Configuration Menus PROTECTION MODE command . . . . . . . . . . . . . 105 87. Commands Menu BULK EXCHANGE command . . . . . . . . . . . . . 107 88. Commands Menu IMPORT command 108 89. RMU displaying the Configuration Menus User screen . . . . . . . . . . . . 109 90. HyperTerminal Connection Description window . . . . . . . . . . . . . 113 91. HyperTerminal Connect To window . . . . 114 92. HyperTerminal COMx Properties window 115 93. Send File window . . . . . . . . . . 117 94. Verification screen . . . . . . . . . . 117 95. RMU login page . . . . . . . . . . 124 96. RMU Information Menus Autoloader page 126 97. RMU Information Menus Drive page 127 98. RMU Status Menus Autoloader page 128 99. RMU Status Menus Media page . . . . . 129 100. RMU Configuration Menus Device page for Model L28/L38/L3H . . . . . . . . . 130 101. RMU Configuration Menus Device page for Model F28/F38/F3H . . . . . . . . . 131 102. RMU Configuration Menus Network page 132 103. RMU displaying the Configuration Menus User screen . . . . . . . . . . . . 133 104. RMU Configuration Menus RTC page 134 105. RMU Configuration Menus Log page 134 106. RMU Configuration Menus Event Notification page . . . . . . . . . . 135 107. RMU Configuration Menus Reset page 136 108. RMU Maintenance Menus Operations page 137 109. RMU Maintenance Menus General Diagnostic page . . . . . . . . . . . 138 110. RMU Maintenance Menus Firmware page 139 111. RMU Maintenance Menus Reset page 139 112. RMU Logs Menus Loader page . . . . . 140 113. RMU Logs Menus Drive page . . . . . . 141
| |
| |
114. The IBM TotalStorage LTO Ultrium 200 GB Data Cartridge . . . . . . . . . . . 115. Sample bar code label on the LTO Ultrium Tape Cartridge . . . . . . . . . . . 116. Setting the write-protect switch . . . . . 117. Tape cartridges in a Turtlecase . . . . . . 118. Double-boxing tape cartridges for shipping 119. Checking for gaps in the seams of a cartridge 120. Leader pin in the incorrect and correct positions . . . . . . . . . . . . . 121. Placing the dislodged leader pin into the correct position . . . . . . . . . . . 122. Rewinding the tape into the cartridge 123. Leader Pin Reattachment Kit . . . . . . 124. Attaching the leader pin attach tool to the cartridge . . . . . . . . . . . . . 125. Winding the tape out of the cartridge 126. Removing the C-clip from the leader pin 127. Attaching the leader pin to the tape . . . . 128. HyperTerminal Connection Description window . . . . . . . . . . . . . 129. HyperTerminal Connect To window . . . . 130. HyperTerminal COMx Properties window 131. Receive File window . . . . . . . . . 132. HyperTerminal Connection Description window . . . . . . . . . . . . . 133. HyperTerminal Connect To window . . . . 134. HyperTerminal COMx Properties window 135. HyperTerminal Capture Text window 136. Removing Autoloader from a rack . . . . 137. Repair Identification Tag . . . . . . . . 138. Autoloader rear panel with the External Fan removed . . . . . . . . . . . . . 139. Removing/replacing the BCR . . . . . . 140. Removing/replacing the RMU . . . . . . 141. Removing/replacing the HVD Converter 142. Types of receptacles . . . . . . . . . 143. Default Element Addresses and Element Indexes . . . . . . . . . . . . . 144. AIX ERRPT Library Error Log Example 145. AIX ERRPT Drive Error Log Example 146. AIX ERRPT Commands Error Log Example 147. Rack mount template . . . . . . . . . 148. Service menu . . . . . . . . . . . 149. RMU Maintenance Menus Advanced Diagnostic page . . . . . . . . . . . 150. Serial port pin-out . . . . . . . . . . 151. HyperTerminal Connection Description window . . . . . . . . . . . . . 152. HyperTerminal Connect To window . . . . 153. HyperTerminal COMx Properties window 154. Configuration Menus DRIVE FW UPGRADE FROM FMR TAPE command . . . . . . 155. Bottom view of cartridge slot . . . . . . 156. Top view of Autoloader with top cover removed showing cartridge slot being removed . . . . . . . . . . . . . 157. Belt loop for cartridge slot pin . . . . . . 158. Location of screws on rear panel for drive removal . . . . . . . . . . . . .
144 146 147 148 149 150 152 153 153 154 155 156 156 157 188 189 190 192 193 194 195 196 205 206 208 210 212 214 221 226 234 235 236 253 255 258 259 260 261 262 264 267
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| 159. Location of screws on bottom cover for drive removal . . . . . . . . . . . . . 272 | 273 | 160. Internal view of drive in Autoloader 275 | 161. Internal view of drive in Autoloader
162. Removing the cover of the tape drive 163. Rewinding the leader pin into the tape cartridge . . . . . . . . . . . . . 164. Guiding the leader pin into the tape cartridge 165. Removing the cover from the internal drive 166. Using hex wrench to rewind tape into cartridge . . . . . . . . . . . . . 167. Drive with cover removed to reveal gear train. . . . . . . . . . . . . . . 276 277 278 280 282 283
| | | | |
| | | | | | | | | | | | |
168. Leader Block Assembly (LBA) . . . . 169. Using hex wrench to rewind tape into cartridge . . . . . . . . . . . 170. Using hex wrench to rewind tape into cartridge . . . . . . . . . . . 171. Drive with cover removed to reveal gear train. . . . . . . . . . . . . 172. Leader Block Assembly (LBA) . . . . 173. Using hex wrench to rewind tape into cartridge . . . . . . . . . . . 174. Drive with cover removed to reveal gear train. . . . . . . . . . . . . 175. Leader Block Assembly (LBA) . . . .
. . . . . . . .
Figures
xi
xii
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Tables
| | | |
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Data access, rewind, and load times . . . . . 4 Performance characteristics of the Ultrium 2 and Ultrium 3 Tape Drive . . . . . . . . 12 SCSI terms and characteristics . . . . . . 13 Physical Specifications for the Autoloader 15 Power Specifications for the Autoloader 15 Acoustic Specifications for the Autoloader 15 Environmental Specifications for the Autoloader . . . . . . . . . . . . . 16 Shipment inventory checklist . . . . . . . 19 Default SCSI IDs for the Autoloaders drive 91 Default Loop IDs for the Autoloaders drive 99 Firmware upload times via different methods 111 Ultrium data and cleaning cartridge compatibility with Ultrium tape drives . . . 143 Environment for operating, storing, and shipping the IBM LTO Ultrium Tape Cartridge . . . . . . . . . . . . . 151 Ordering media supplies for the Autoloader 159 Authorized suppliers of custom bar code labels . . . . . . . . . . . . . . 160 Ordering media supplies for the Autoloader 160 Start Here . . . . . . . . . . . . . 163 Not Ready Errors 01h - 0Fh . . . . . . . 169 Unit Attention 10h - 1Fh . . . . . . . . 169 Recovered Errors 20h - 2Fh . . . . . . . 169 Hardware Errors 30h - 4Fh . . . . . . . 170 Illegal Request Errors 50h - 6Fh . . . . . 170 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. Aborted Command Errors 70h - 73h . . . . Additional Errors 7Ah - 7Fh . . . . . . Error 80h . . . . . . . . . . . . . Robotic Control Errors 81h - 8Fh . . . . . Function Errors 90h - 9Fh . . . . . . . Low Level Axis Errors A0h - AFh . . . . . Electronic Hardware Errors B0h - B9h Drive Errors BAh - BFh . . . . . . . . Drive Errors C0h - CFh . . . . . . . . Drive Errors D0h - D5h . . . . . . . . Network Error F0h - F3h . . . . . . . . Subcode Descriptions . . . . . . . . . Drive error codes . . . . . . . . . . Parts list for the 3581 Tape Autoloader Power cord information . . . . . . . . TapeAlert Flags supported by the Autoloader TapeAlert flags supported by the drive AIX ERRPT Library Sense Data . . . . . AIX ERRPT Drive Sense Data . . . . . . Autoloader Sense Data . . . . . . . . Autoloader possible Additional Sense Codes (ASC) and Additional Sense Code Qualifiers (ASCQ) . . . . . . . . . . . . . LTO Tape Drive Sense Data . . . . . . . Host Method of Recording Tape Drive Errors Telephone numbers and e-mail addresses for IBM Customer Assistance Centers. . . . . 171 171 172 172 173 174 174 175 175 176 176 176 179 217 218 227 229 234 235 241
| |
| | | |
| 17.
18. 19. 20. 21. 22.
xiii
xiv
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Danger Notice
A danger notice calls attention to a situation that is potentially lethal or extremely hazardous to people. A lightning bolt symbol always accompanies a danger notice to represent a dangerous electrical condition.
Caution Notice
A caution notice calls attention to a situation that is potentially hazardous to people because of some existing condition. A caution notice can be accompanied by one of several symbols:
If the symbol is... It means.... A hazardous electrical condition with less severity than electrical danger.
A hazardous condition due to the use of a laser in the product. Laser symbols are always accompanied by the classification of the laser as defined by the U. S. Department of Health and Human Services (for example, Class I, Class II, and so forth). A hazardous condition due to mechanical movement in or around the product.
xv
It means.... A hazardous condition due to the weight of the unit. Weight symbols are accompanied by an approximation of the products weight.
Intended Use
This equipment is designed for processing magnetic tape cartridges. Any other application is not considered the intended use. IBM shall not be held liable for damage arising from unauthorized use of the Autoloader. The user assumes all risk in this aspect.
Safeguards
To maintain safeguards, observe the following basic rules for installation, use, and servicing of the Autoloader. v Follow Warnings - Adhere to all warnings on the product and in the operating instructions. v Read Instructions - Read and follow all installation and operating instructions. v Ventilation - Situate the Autoloader so that its location or position provides adequate front and rear ventilation (at least two inches). v Heat - Situate the product away from heat sources such as radiators, heat registers, furnaces, or other heat-producing appliances. v Power Sources - Connect the Autoloader to a power source only of the type directed in these operating instructions or as marked on the product label. v Power Cord Protection - Route the AC line cord so that it is not likely to be walked on or pinched by items placed upon or against it, paying particular attention to the cord at the wall receptacle, and the point where the cords exits from the product.
xvi
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
v Object and Liquid Entry - Take care to ensure that objects do not fall and liquids are not spilled into the products enclosure through openings. v Servicing - Do not attempt to service the product beyond that described in the operating and installation instructions. All other servicing should be referred to qualified service personnel.
Precautions
Use these precautions when using or choosing an environment for the unit: v Do not use oil, solvents, gasoline, paint thinners, or insecticides on the unit or near the unit. Vapors from these types of chemicals can damage the tape media components. v Do not expose the unit to moisture or store the unit in temperatures higher than 60C (140F), or to extreme low temperatures. See Specifications on page 15 for operating temperatures. v Keep the unit away from direct strong magnetic fields, excessive dust, and electronic or electrical equipment that generates electrical noise. v Hold the AC power plug by the head when removing it from the AC source outlet; pulling the cord can damage the internal wires. v Use the unit on a firm, level surface free from vibration. Do not place any objects on top of the unit..
| | | | | | |
xvii
xviii
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Related Publications
Refer to the following publications for additional information about the Autoloader. To ensure that you have the latest versions of the publications, visit the web at http://www.ibm.com/storage/support/lto. |
| | |
Redbooks
v The IBM LTO Ultrium Tape Libraries Guide provides information on all LTO tape drive products.
xix
| | | | |
v Using IBM LTO Ultrium with Open Systems, SG-6502, provides information on all LTO tape drive products. v Implementing IBM LTO in Linux and Windows, SG-6268, provides information on all LTO tape drive products.
Safety Publications
v IBM Externally Attached Devices Safety Information, SA26-2004, provides translations of safety notices.
SCSI Publications
v SCSI-3 Stream Commands (SSC), published by the American National Standards Institute and available on the web at http://www.t10.org. v SCSI Primary Commands-2 (SPC-2), published by the American National Standards Institute and available on the web at http://www.t10.org.
| | | | | | | | | | | | | | |
IBM Redbooks
v http://w3.itso.ibm.com/
Device Drivers
v ftp://ftp.software.ibm.com/storage/devdrvr v ftp://index.storsys.ibm.com/358x
xx
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| |
xxi
xxii
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | |
RMU Cabling . . . . . . . . . SCSI Interface . . . . . . . . Attaching to a SCSI-LVD System . Attaching to a SCSI-HVD System . Fibre Channel Interface . . . . . Step 11. Power on the Autoloader . . . Configuring Your Autoloader . . . . Saving / Restoring VPD on the RMU.
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
38 38 38 39 39 41 41 41
| | | |
| | |
| | | | |
Installation . . . . . . . . . . . . . Step 1. Unpack the Autoloader . . . . . . . Step 2. Verify the Shipment Inventory . . . . Step 3. Inspect the Power Cord and Outlet . . . Step 4. Install the Optional Remote Management Unit (RMU) . . . . . . . . . . . . . Tools Required . . . . . . . . . . . Installing the RMU . . . . . . . . . . Step 5. Install the Optional HVD Converter (L28 Models Only) . . . . . . . . . . . . . Tools Required . . . . . . . . . . . Installing the HVD Converter . . . . . . Step 6. Install the Optional Bar Code Reader (BCR) Tools Required . . . . . . . . . . . Installing the BCR . . . . . . . . . . Step 7. Install the Autoloader as a Desktop Unit . Step 8. Install the Autoloader in a Rack . . . . Rack Safety . . . . . . . . . . . . Rack Installation . . . . . . . . . . Rack Relocation (19 Rack) . . . . . . Tools Required . . . . . . . . . . . Verify the Rack Mount Kit . . . . . . . Check the Installation Environment . . . . Prepare the Autoloader for Installation . . . Install the Support Rails in the Rack . . . . Install the Rack Front-Mount Brackets on the Autoloader . . . . . . . . . . . . Secure the Autoloader to the Rack . . . . . Step 9. Connect Power . . . . . . . . . . Desktop Installation . . . . . . . . . Rack Installation . . . . . . . . . . . Running a Drive Recalibration Test . . . . LIBRARY VERIFY Test. . . . . . . . . Step 10. Connect the Autoloader to Your Server (Host) . . . . . . . . . . . . . . .
Copyright IBM Corp. 2004, 2005
. 22 . 22 . 22 . 23 . 23 . 23 25 . 25 . 25 . 26 . 27 . 27 . 27 . 28 . 28 . 28 . 30 . 31 . 31 . . . . . . . 33 34 36 36 36 37 37
. 38
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Product Description
| | | | | | | | | | | | | | | | | | | | | | The IBM TotalStorage Ultrium Tape Autoloader 3581 Models L28/L38/L3H and F28/F38/F3H offer high capacity, performance, and technology designed for the mid-range open systems environment. These models incorporate a single Linear Tape Open (LTO) IBM TotalStorage Ultrium 2 (Models L28/F28) or Ultrium 3 (Models L38/F38/L3H/F3H) Tape Drive. The IBM TotalStorage Ultrium 3 Tape Drive more than doubles tape drive performance over the previous generation Ultrium 2 Tape Drive, with up to 80 MB per second native data transfer rate. In addition, with the use of the new IBM TotalStorage Ultrium 400 GB Data Cartridge, the Ultrium 3 Tape Drive has the capability of writing twice as much data, up to 400 GB native capacity (800 GB with 2:1 compression). The Model L28/L38/L3H comes with an LVD Ultra160 SCSI attachment, while the Model F28/F38/F3H comes with a Native Switched Fabric Fibre Channel attachment, for connection to a wide spectrum of open systems servers. Both models connect to a wide spectrum of open systems servers. Note that the Ultrium 3 Tape Drive does not support HVD technology. The 3581 Tape Autoloader is a desktop or rack-mountable unit (requiring two rack units) that operates in automatic, sequential, or random mode and comes equipped with a robotic interface that moves tape cartridges to and from the drive and cartridge carousel. With an eight tape cartridge capacity, it provides a media capacity of up to 3.2 TB (6.4 TB with 2:1 compression) data storage per unit. Optional features include an HVD Converter, a Remote Management Unit (RMU), and a Bar Code Reader (BCR).
Figure 2. IBM TotalStorage Ultrium Tape Autoloader 3581 Models L28/L38/L3H and F28/F38/F3H
| |
The Autoloaders Ultrium 2 and Ultrium 3 Tape Drive offer: v Digital speed matching The Ultrium 2 and Ultrium 3 Tape Drive will perform dynamic speed matching to adjust the drives native data rate as closely as possible to the net host data rate (after data compressibility has been factored out). This offers the dual benefit of reducing the number of backhitch repositions and improving throughput performance. v Power management
a67s0243
The power management function controls the drives electronics to be either completely turned off or to be in a low-power mode. These power modes occur only when the circuit functions are not needed for drive operation. v Channel calibration The channel calibration feature allows for customization of each read/write data channel for optimum performance. The customization enables compensation for variations in the recording channel transfer function, media characteristics, and read/write head characteristics. v Separate writing of multiple filemarks Separate writing of multiple filemarks causes any write command of two or more filemarks to cause a separate data set to be written containing all filemarks after the first. This feature has two advantages: - First, it can improve performance if a subsequent append overwrites somewhere after the first filemark. - Second, write of multiple filemarks typically indicates a point where an append operation might occur after the first of these filemarks. This change prevents having to rewrite datasets containing customer data and the first filemark in cases when (where) such an append occurs. v Large internal buffer The Ultrium 2 Tape Drive and has a 64 MB internal data buffer. The Ultrium 3 Tape Drive has a 128 MB internal buffer . v Fast cartridge fill times (for Ultrium 3, Ultrium 2 and Ultrium 1 data cartridges) v Fast data access, rewind, and load times
Table 1. Data access, rewind, and load times Action Cartridge Load Time Maximum Rewind Time Average File Access Time Autoloader 32 seconds N/A N/A Ultrium 2 Tape Drive 15 seconds 80 seconds 49 seconds Ultrium 3 Tape Drive 10 seconds 88 seconds 49 seconds
| | | | | | | | |
Product Features
This section describes the standard and optional features of the Autoloader.
Standard Features
The Autoloader includes the following standard features: v Operator Control Panel (OCP) The OCP provides an easy-to-read display and a four button keypad allowing the user to monitor and control the operations of the Autoloader. The OCPs display provides access to library status, commands, setup, and tools. See Front Panel Components on page 7 and Operator Control Panel (OCP) on page 46 for additional information. v Robotic system The Autoloaders robotic system includes an I/O Door, a cartridge carousel with cartridge slots, and a cartridge loader. The I/O Door allows importing or exporting a single cartridge to or from the Autoloader. The cartridge carousel encircles the Ultrium 2 and Ultrium 3 Tape Drive and positions the specified cartridge slot in front of the tape drive. A robotic cartridge loader moves the cartridges between the cartridge slots and the tape drive.
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
v Eight-cartridge capacity Up to eight Ultrium 3, Ultrium 2 or Ultrium 1 tape cartridges can be stored in cartridge slots mounted on the carousel. v Cartridge inventory Each time the Autoloader is powered on, an inventory of all cartridge slots is performed.
| | |
v Built-in diagnostics The Autoloader includes firmware that performs diagnostic tests and reports drive operating status. An error and event log is available through the OCP or optional RMU. v Ultrium 2 or Ultrium 3 Tape Drive The Autoloader is available with an LVD SCSI (Model L28/L38/L3H) or a Fibre Channel (Model F28/F38/F3H) Ultrium 2 or Ultrium 3 Tape Drive.
Optional Features
The Autoloader has the following optional features: v Bar Code Reader (BCR) The BCR reads bar code labels and sends the label IDs to the server (host) and to the Remote Management Unit (RMU), if installed. v Remote Management Unit (RMU) The RMU provides remote access to the Autoloader over a network via a web browser and makes functions accessible without the need for a dedicated server or separate software. v HVD Converter The HVD Converter is a SCSI HVD to LVD converter/expander. It converts the Autoloaders low voltage differential (LVD) to wide high voltage differential (HVD). This allows LVD-peripherals to be used on an HVD bus. The converter can also be used to reshape poor quality LVD signals, and allow additional cable length. v Rack Mount Kit The Rack Mount Kit supplies the necessary mounting hardware to install the Autoloader in a 19-inch rack.
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Component Descriptions
This section contains descriptions of the following: v Front Panel Components v Interior Components on page 8 v Rear Panel Components on page 10
1 POWER button For powering the Autoloader on and off. 2 I/O Door Allows the user to insert or remove cartridges from the Autoloader. 3 Operator Control Panel (OCP) Allows the operator to control the Autoloader without a Remote Management Unit (RMU) and contains the following: - Status LEDs (4) - Liquid crystal display (OCP display) - Keypad with four buttons (Cancel, Previous, Next, Enter) 4 Serial Number A label with machine type, model, and serial number.
Interior Components
Figure 4 shows the Autoloaders interior components and one cartridge slot. | | |
Attention: Only IBM Authorized Service Personnel should remove the Autoloaders cover.
| |
2 1
Figure 4. Interior components with one cartridge slot
a67s0179
| | | | | | | | | |
1 Cartridge slot Each cartridge is installed in a cartridge slot to ensure the cartridge is properly aligned for insertion into the tape drive. 2 Cartridge loader The cartridge loader moves cartridges between the cartridge slots and the tape drive. When a cartridge slot is positioned in front of the drive, the loader grips the sides of the cartridge and slides it forward or backward between the slot and drive. The loader then releases the cartridge and pushes it firmly into the drive or slot. 3 Ultrium 2 or Ultrium 3 Tape Drive (LVD or Fibre Channel) Generation 2 models of the Autoloader contain one LVD (Model L28) or Fibre Channel (Model F28) Ultrium 2 Tape Drive. The drive can sustain a maximum data transfer rate of 107 MB per second (compressed) and can store up to 400 GB of compressed information on a single data cartridge (assuming an average compression ratio of 2:1.) Generation 3 models of the Autoloader contain one LVD (Model L38/L3H) or Fibre Channel (Model F38/F3H) Ultrium 3 Tape Drive. The drive can sustain a maximum data transfer rate of 160 MB per second and can store up to 800 GB of compressed information on a single data cartridge (assuming an average compression ratio of 2:1).
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
4 Carousel The carousel stores up to eight Ultrium 3, Ultrium 2 or Ultrium 1 data cartridges. The carousel consists of a drive chain, guides, and gears that move the cartridges into position in front of the drive.
Provides AC power and chassis grounding to the Autoloader. 2 Power Ratings / Warning Label A label showing power ratings and warning the customer not to remove the cover of the Autoloader.
| | |
Figure 5. Rear panel label showing power ratings and warning customers not to remove the Autoloader cover
v v
3 Fan Provides cooling for the Autoloader. 4 Serial Port Allows serial communication between the Autoloader and a server (host).
| | | | | | | | |
Figure 6 shows the rear panel components of the Autoloader with an LVD SCSI (Model L28/L38/L3H) drive. v 5 SCSI Receptacles The Autoloader has two HD68 SCSI receptacles for connecting the Autoloader to a single LVD SCSI bus to accommodate one of the following: - A SCSI cable connecting the Autoloader to a server (host). - A wide external terminator or a cable to another SCSI device.
a67s0271
| | |
Figure 6. Rear panel with standard elements and SCSI connectors with an LVD SCSI (Model L28lL38/L3H) drive
Figure 7 on page 11 shows the rear panel components of the Autoloader with an LVD SCSI drive (Model L28/L38/L3H) and HVD Converter. v 1 Optional HVD Converter
10
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0202
Used to convert an Autoloader with an LVD SCSI drive to communicate with an HVD system.
Figure 7. Rear panel components with an LVD SCSI drive (Model L28/L38/L3H) and HVD Converter
| | | | | |
Figure 8 shows the rear panel components of the Autoloader with a Fibre Channel (Model F28/F38/F3H) drive. v 1 Fibre Channel Receptacle The receptacle for the Fibre Channel interface cable that connects the Autoloader with the server (host).
1
Figure 8. Rear panel with a Fibre Channel (Model F28/F38/F3H) drive connection
Media
| The Autoloader uses the following cartridge types: v v IBM TotalStorage LTO Ultrium 400 GB Data Cartridge (Ultrium 3) v IBM TotalStorage LTO Ultrium 200 GB Data Cartridge (Ultrium 2) v IBM LTO Ultrium Data Cartridge (Ultrium 1 with 100 GB capacity) v IBM TotalStorage LTO Ultrium Cleaning Cartridge v LTO Ultrium Cleaning Cartridge (universal cleaning cartridge compatible with Ultrium 3, Ultrium 2 and Ultrium 1 drives) For additional information, refer to Media on page 143.
| |
a67s0204
a67s0197
11
Nominal load-to-ready time Nominal unload time Average search time to first byte of data
Note: Although the Autoloader provides the capability for high tape performance, the actual throughput is a function of many components, such as system processor, disk data rate, data block size, data compressibility, I/O attachments, and the system or application software used. For example, the HVD Ultra SCSI converter interface has a maximum data transfer rate of 40 MB/second, so Ultrium Tape Drives on that SCSI interface will have a lower data transfer rate. The compression technology used in the tape drive can typically double the amount of data that can be stored on the media; however, the actual degree of compression achieved is highly sensitive to the characteristics of the data being compressed.
Interfaces
The Autoloader is available with a choice of interfaces, either SCSI HVD (with the optional HVD Converter or) LVD, or Fibre Channel.
12
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
Note: A faster bus does not imply that an attached device will support that data rate, but that multiple devices can operate on the bus at that maximum speed. For a detailed table of SCSI terms and related specifications, refer to the SCSI Trade Association Web site at http://www.scsita.org/terms/scsiterms.html. To ensure best performance, if possible, avoid daisy-chaining.
13
| | | | | | |
The Autoloader allows the selection of the following Fibre channel port behaviors: v LN Port: (default setting) an automatic configuration that tries arbitrated loop first, then switched fabric. v NL Port: an automatic configuration that tries switched fabric first, then arbitrated loop. v L Port: arbitrated loop. v N Port: point to point protocol in a switched fabric topology.
| |
To determine the latest supported attachments and host software versions and releases, visit the web at http://www.ibm.com/storage/support/lto. Select LTO Support, then the Interoperability Matrix and Software ISVs, and view the Supported Servers and Operating Systems. Note: 1. IBM does not provide backup application software with the Autoloader. To order software, contact your IBM marketing representative, IBM Business Partner, or an independent software provider. 2. If you attach your library to a non-IBM platform with non-IBM software, IBM recommends that you contact your software vendor to obtain a matrix of compatible hardware, software, firmware revisions, and adapter cards.
14
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
TapeAlert Support
The Autoloader is compatible with TapeAlert technology, which provides error and diagnostic information to the server (host). For more information, see TapeAlert Flags on page 227.
Specifications
Specifications for the Autoloader are listed in the following tables below: v Table 4 for Physical Specifications v Table 5 for Power Specifications v Table 6 for Acoustic Specifications v Table 7 on page 16 for Environmental Specifications Specifications for tape cartridges are given in Environmental and Shipping Specifications for Tape Cartridges on page 151.
Table 4. Physical Specifications for the Autoloader Physical Specifications Desktop Version Rack Mount Version 483 mm/19 in. 660 mm/26 in. 89 mm/3.5 in.
| |
Table 5. Power Specifications for the Autoloader Power Specifications AC line voltage Line frequency Line current at 100 Vac Line current at 240 Vac Maximum heat output 100 to 240 Vac 50 to 60 Hz auto-ranging 1.3 A 0.7 A 100 watts (86 KCAL/hr.)
Table 6. Acoustic Specifications for the Autoloader Acoustic Specifications Maximum noise level Idling 60 db (6.3 bels) Operating 62 db (6.5 bels)
15
Table 7. Environmental Specifications for the Autoloader Environmental Specifications Environmental Factor Temperature Temperature Variation Relative humidity (noncondensing) Wet bulb (max.) Power On +10C to +35C 10C/Hr max 15% to 85% 26C 0 to 2500 Power Off1 +10C to 43C 10C/Hr max 10% to 90% 27C 0 to 2500 Storage2 1C to 60C 10C/Hr max 10% to 90% 29C 0 to 2500 Shipment2 -40C to +60C 10C/Hr max 10% to 90% 29C 0 to 12192
Altitude (meters)
Note: The operating environment of the Autoloader must not conflict with the media storage requirements (see Environmental and Shipping Specifications for Tape Cartridges on page 151). While the Autoloader may be capable of operating at elevated temperatures for an extended period of time, the temperature could shorten the useful life of media that is stored in the Autoloader. If media is stored in the Autoloader for more than 10 hours, the storage temperature requirements for media should be met. It should be assumed that media stored in the Autoloader will be 2 degrees above ambient room temperature when the Autoloader is powered on. 1. Values indicated are valid for the unpacked unit with no data cartridge. If there is a cartridge with the unit either inside or out, then the Power On specification must apply to the Power Off situation. 2. Values indicated are valid for the packaged unit. The storage period should not exceed three (3) years. The limits are for the ambient temperature within 1 meter from the packaged unit.
16
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Installation
Installation and configuration of the Autoloader can be accomplished by following the steps outlined in this chapter. If some options were not purchased with the Autoloader, skip the steps related to installing those options not purchased and proceed to the next step to continue the installation.
Attention 1. The Autoloader is a customer setup unit. It is the customers responsibility to install this product. 2. The Autoloader Models L28/L38/L3H and F28/F38/F3H offer a 3-year warranty. These models are designed as Customer Replaceable Units (CRU). The warranty is a parts-only warranty. For details about the Customer Replaceable Unit process and customer responsibilities, see Statement of Limited Warranty on page 298. To install the Autoloader, complete the following steps. For more information, refer to the instructions for each step in this chapter. __ v Step 1. Unpack the Autoloader on page 18 __ v Step 2. Verify the Shipment Inventory on page 19 __ v Step 3. Inspect the Power Cord and Outlet on page 21 __ v Step 4. Install the Optional Remote Management Unit (RMU) on page 22 __ v Step 5. Install the Optional HVD Converter (L28 Models Only) on page 23 __ v Step 6. Install the Optional Bar Code Reader (BCR) on page 25 __ v Step 7. Install the Autoloader as a Desktop Unit on page 26 __ v Step 8. Install the Autoloader in a Rack on page 27 __ v Step 9. Connect Power on page 36 __ v Step 10. Connect the Autoloader to Your Server (Host) on page 38 __ v Step 11. Power on the Autoloader on page 41 For detailed instructions on performing each step, refer to the sections that follow.
17
18
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
One IBM TotalStorage LTO Ultrium 200 GB Data Cartridge (to be used for diagnostic purposes) One IBM TotalStorage Ultrium Cleaning Cartridge (universal) One Device Driver Installation Kit that includes: v CD that contains Open System device drivers, the IBM Ultrium Device Drivers Installation and Users Guide, and the IBM Ultrium Device Drivers Programming Reference v Published copy of the IBM Ultrium Device Drivers Installation and Users Guide One SCSI Ultra 2 LVD/SE terminator (with Model L28/L38/L3H)
SC
SI
T UL
RA
VD 2L
/S
One fiber cable ( 1 with Model F28/F38/F3H) or one SCSI cable ( 2 with Model L28/L38/L3H)
a1400419
One SCSI LVD wrap tool ( 1 with Model L28/L38/L3H) or one Fiber wrap tool ( 2 with Model F28/F38/F3H)
SC
SI
D LV
RA W
O TO
a67s0194
a67s0195
19
Autoloader documentation CD-ROM containing: v This document, the IBM TotalStorage Ultrium Tape Autoloader 3581 Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide which includes the Limited Statement of Warranty v The IBM TotalStorage Ultrium Tape Autoloader Models L28/L38/L3H and F28/F38/F3H Quick Reference v The IBM Externally Attached Devices Safety Information manual, SA26-2004 The Quality Hotline card
PCC cable for Autoloader installed in a rack (cable included in ship group when Rack Mount Kit is ordered)
a67s0273
If your order has missing parts or was damaged in shipment, please contact your place of purchase or refer to the Quality Hotline card included with your shipment.
20
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0196
21
Tools Required
v T10 Torx wrench or small flat-blade screwdriver | | | | | |
CAUTION: ESD Sensitive Component. Please touch the unit cover or rear panel before installing the RMU to avoid electrostatic discharge.
1
Figure 9. Installing the RMU
1. Remove the RMU cover plate ( 1 ) located below the BCR on the Autoloaders rear panel. Save the screw.
CAUTION: Avoid contact with the card on the RMU.
2. Slide the RMU card into the guide slots at the bottom of the RMU opening on the rear panel of the Autoloader. 3. Insert and tighten the screw previously removed from the cover plate. 4. For instructions on connecting the RMU to a server (host), see RMU Cabling on page 38.
22
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0203
Step 5. Install the Optional HVD Converter (L28 Models Only) Tools Required
| | | | | | | v T10 Torx wrench or small flat-blade screwdriver
CAUTION: ESD Sensitive Component. Please touch the unit cover or rear panel before installing the HVD Converter to avoid electrostatic discharge.
__ 5. Using the small flat-blade screwdriver, tighten the two thumbscrews ( 5 ) on the converter.
23
8 7 9
Figure 11. Installing the HVD Converter
6
a67s0200
__ 6. Plug in and secure the converters SCSI cable into the top SCSI receptacle ( 6 ) on the rear panel of the Autoloader. __ 7. Plug in and secure the LVD terminator into the bottom SCSI receptacle ( 7 ) on the rear panel of the Autoloader.
DI
FF
E ER
NT
IA
LT
M ER
IN
OR AT
__ 8. For instructions on connecting the Autoloader to an HVD system via the receptacles ( 8 and 9 ) on the HVD Converter , see Attaching to a SCSI-HVD System on page 39.
24
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0236
Tools Required
| v T10 Torx wrench or small flat-blade screwdriver
CAUTION: ESD Sensitive Component. Please touch the unit cover or rear panel before installing the BCR to avoid electrostatic discharge.
| | |
| | | | |
__ 1. Remove the cover plate from the rear panel. Save the screws. Store the cover plate for reinstallation if the BCR is ever removed. __ 2. With the No Handle label ( 1 ) facing up, connect the cable ( 3 ) to the BCRs controller outlet. __ 3. Align the screw holes ( 2 ) on the BCR with the holes left by the cover plate on the rear panel of the Autoloader to ensure correct placement. Feed the remainder of the cable back into the BCR so it will not block the BCR lens. __ 4. Using the Torx wrench or small flat-blade screwdriver, attach the BCR with the saved screws from the cover plate.
25
a67s0198
| |
For instructions on connecting power to the Autoloader when installed as a desktop unit, see Step 9. Connect Power on page 36.
26
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Rack Safety
Rack Installation
DANGER v Always lower the leveling pads on the rack cabinet. v Always install stabilizer brackets on the rack cabinet. v To avoid hazardous conditions due to uneven mechanical loading, always install the heaviest devices in the bottom of the rack cabinet. Always install servers and optional devices starting from the bottom of the rack cabinets. v Rack-mounted devices are not to be used as a shelf or work space. Do not place any object on top of rack-mounted devices. v Each rack cabinet might have more than one power cord. Be sure to disconnect all power cords in the rack cabinet before servicing any device in the rack cabinet. v Connect all devices installed in a rack cabinet to power devices installed in the same rack cabinet. Do not plug a power cord from a device installed in one rack cabinet into a power device installed in a different rack cabinet.
27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
Tools Required
v #2 Phillips screwdriver v T10 Torx wrench (provided in kit)
28
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
__ __ __ __ __ |
Ten screws Ten washers Ten panel clip-nuts (for racks with round mounting holes) Ten cage clip-nuts (for racks with square mounting holes) Torx wrench
2-FRONT
10 x SCREW, PAN HEAD, RECESSED PHILIPS 1 x Torx Wrench 10 x NUT, PANEL, ROUND HOLE
| | |
29
a67s0242
| | | | |
Included in the ship group when a Rack Mount Kit is ordered is a PCC cable for Autoloaders installed in a rack. This cable connects the Autoloader to the racks power strip.
a67s0273
| | |
30
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | | |
Note: One EIA is equal to 4.45 cm (1.75 in.). v If your rack contains a rail with each EIA numbered: a. Hold the rack template on the outside of the selected 2 EIAs (aligning all six circles on the template with the holes in the 2 EIAs) on each rail. v If your rack does not contain a rail with each EIA numbered: a. Locate the Rack Mount Template in the Quick Reference of the Rack Mount Template on page 253.
31
| | | | | |
b. To identify the 2 EIAs required by the Autoloader, hold the rack template on the outside of the rack rail and align all six circles on the template with the holes in the rack rail. Note: All six circles on the template must align exactly with the holes of the 2 EIAs in the rack rail. __ 3. Install clip-nuts in the rail holes indicated by the filled circles on the template. v Top hole of the higher EIA v Top hole of the lower EIA v Bottom hole of the lower EIA Note: Two types of clip-nuts are included with the Rack Mount Kit: v Panel clip-nuts (for racks with round mounting holes) slip on from the side of the rail with the largest part of the clip-nut going on the back side of the rail. v Cage clip-nuts (for racks with square mounting holes) are installed from the back side of each rail.
| | | | |
| |
Note: To ensure proper installation of the Autoloader in your rack, it is very important to install the clip-nuts in the correct positions on each rail. __ 4. Count the holes on the other three rack rails, up or down, to determine the position of the top or bottom clip-nut. Use the Rack Mount Template to install the other two clip-nuts. __ 5. From the front of the rack, position one of the rails on the appropriate side. Position the front flange so that it is on the outside of the strip of mounting holes in the rack (see Figure 18 on page 33).
32
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0205
|
2 1 1
4 3
3
7 8
4 5
| | |
__ 6. Using a #2 Phillips screwdriver, attach the rail to the rack with screws and washers from the kit. __ 7. Slide the rail pieces apart to match the depth of your rack. __ 8. Using a #2 Phillips screwdriver, attach the rail to the outside of the rack with screws and washers supplied with the Rack Mount Kit. __ 9. Repeat Steps 4 through 7 to install the second rail. |
33
a67s0206
| | | | |
__ 2. Using the Torx wrench, remove the two screws on each side of the Autoloader cover. __ 3. Position the correct bracket, as determined in Step 1, on each side of the Autoloader and secure by replacing the original screws (see Figure 19).
34
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0207
2-FRONT
2
a67s0208
| | | | | |
__ 2. Place one screw and washer from the Rack Mount Kit into the hole in the front of each bracket. The screws should line up with the holes containing the remaining installed clip-nuts. Use a #2 Phillips screwdriver to tighten the screws. Note: For information on connecting a power cable to an Autoloader installed in a rack, see Step 9. Connect Power on page 36.
35
Desktop Installation
To connect power to a desktop Autoloader: __ 1. Plug the power cord into the receptacle at the rear of the Autoloader, then plug the other end into a grounded electrical outlet. __ 2. Power on the Autoloader. The Autoloader will verify the drive configuration and status, build a valid cartridge inventory log, and calibrate the robotic cartridge loader. The OCPs green READY/ACTIVITY LED (light-emitting diode) will blink during this initialization process. When the Autoloader completes the Power-On Self Test (POST) for the drive and the library, the green READY/ACTIVITY LED will stop blinking. The Autoloader will be in automatic mode (the default mode) and SEQ will appear in the lower right corner of the OCP display. For information about the Autoloaders modes of operation, see CHANGE LDR MODE on page 92. If a failure occurred, the red ERROR LED will light up and an error message will be displayed on the OCP. Refer to Troubleshooting on page 163. __ 3. If the power on is successful, run the Drive Recalibration test and the Library Verify test.
Rack Installation
To connect power to an Autoloader installed in a rack: 1. Connect the PCC cable (included with your Rack Mount Kit) to the rear of the Autoloader.
a67s0273
| | | | | | | | | | | | | | | |
2. Connect the other end of the PCC cable to your racks power strip. 3. Power on the power strip. 4. Power on the Autoloader. The Autoloader will verify the drive configuration and status, build a valid cartridge inventory log, and calibrate the robotic cartridge loader. The OCPs green READY/ACTIVITY LED (light-emitting diode) will blink during this initialization process. When the Autoloader completes the Power-On Self Test (POST) for the drive and the library, the green READY/ACTIVITY LED will stop blinking. The Autoloader will be in automatic mode (the default mode) and SEQ will appear in the lower right corner of the OCP display. For information about the Autoloaders modes of operation, see CHANGE LDR MODE on page 92. If a failure occurred, the red ERROR LED will light up and an error message will be displayed on the OCP. Refer to Troubleshooting on page 163. 5. If the power on is successful, run the Drive Recalibration test and the Library Verify test.
36
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | | | | | | |
37
RMU Cabling
To connect the RMU to a network switch or hub or directly to a server (host): 1. Plug an Ethernet cable into the RMU mounted on the rear of the Autoloader. 2. Plug the other end of the Ethernet cable into your network switch or hub. Note: If you are plugging the RMU directly into a PC, use a special crossover Ethernet cable (not supplied).
SCSI Interface
A SCSI cable is required for each server connection to a SCSI bus. An LVD SCSI terminator is included in your ship group. Attention: Be sure to install the appropriate SCSI host bus adapter and software on your server (host). For more information, refer to your server (host) documentation and application software. |
38
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
__ Step 2. Plug the LVD SCSI terminator (or another SCSI cable connecting to another SCSI device) into the bottom SCSI receptacle ( 2 ) on the rear panel of your Autoloader. __ Step 3. Connect the SCSI cable to your server (host). |
2
Figure 23. SCSI receptacles on HVD Converter
3. Plug the HVD Differential terminator into the bottom SCSI receptacle ( 2 ) on the HVD converter. 4. Connect the SCSI cable to the server (host).
a67s0232
a67s0233
39
1
Figure 24. Fibre Channel receptacle
__ 2. Connect the fiber cable to your network switch or hub or directly into your server (host).
40
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0204
41
| | | | |
v v v v v
Operating Mode Fibre Channel Drive Speed BCR Enablement Machine Serial Number WWNN
42
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
. . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45 45 46 47 47 49 49 50 52 53 53 54 55 55 55 56 56 57 58 58 58 60 60 60 61 61 62 62 63 63 64 65 66 67 67 67 70 74 75 76 76 76 76 76 77 77 78 78 78 79 80 80 82 82 83
. .
. .
. .
. .
. .
. .
. .
. .
. .
. .
. 84 . 84
| |
| | | | |
| |
Configuration . . . . . . . . . . . . . 85 Passwords . . . . . . . . . . . . . . . 85 OCP Password . . . . . . . . . . . . 85 Going Offline with Password Protection OFF 85 Going Offline with Password Protection ON 85 RMU Passwords . . . . . . . . . . . . 86 Logging in the First Time . . . . . . . . 86 Serial Communication Password . . . . . . 86 Using HyperTerminal . . . . . . . . . 86 Configuring a Model L28/L38/L3H Autoloader . . 91 Step 1. Go Offline Using the OCP . . . . . . 91 Step 2. Change SCSI ID . . . . . . . . . 91 Step 3. Change SCSI Speed . . . . . . . . 92 Step 4. Change the Operating Mode . . . . . 92 CHANGE LDR MODE . . . . . . . . 92 LOOP MODE . . . . . . . . . . . . 93 AUTOLOAD MODE . . . . . . . . . 94 Step 5. Configure the RMU . . . . . . . . 95 Configuring Network Parameters . . . . . 95 Step 6. Configure the BCR . . . . . . . . 96 Step 7. Cycle Autoloader Power . . . . . . 96 Step 8. Set Protection Mode ON or OFF . . . . 97 Step 9. Save Vital Product Data (Autoloader with RMU Only) . . . . . . . . . . . . . 97 Step 10. Update Autoloader Configuration Form 98 Configuring a Model F28/F38/F3H Autoloader . . 99 Step 1. Go Offline Using the OCP . . . . . . 99 Step 2. Change Loop ID . . . . . . . . . 99 Step 3. Select Fibre Channel Port . . . . . . 100 Step 4. Enter WW Node Name . . . . . . 100 Step 5. Change Fibre Channel Speed . . . . 100 Step 6. Change the Operating Mode . . . . . 101 CHANGE LDR MODE . . . . . . . . 101 LOOP MODE . . . . . . . . . . . 102 AUTOLOAD MODE . . . . . . . . . 102 Step 7. Configure the RMU . . . . . . . . 103 Configuring Network Parameters using the OCP . . . . . . . . . . . . . . 103 Step 8. Configure the BCR . . . . . . . . 104 Step 9. Cycle Autoloader Power . . . . . . 104 Step 10. Set Protection Mode ON or OFF . . . 105 Step 11. Save Vital Product Data (Autoloader with RMU Only) . . . . . . . . . . . 105 Step 12. Update Autoloader Configuration Form 106 Completing Configuration of Autoloader . . . . 107 Step 1. Import Cartridges . . . . . . . . 107 BULK EXCHANGE . . . . . . . . . 107 IMPORT . . . . . . . . . . . . . 108 Step 2. Configure RMU User Accounts . . . . 108 Starting the RMU . . . . . . . . . . 108 Logging in the First Time . . . . . . . 108 Configuring User Accounts . . . . . . . 109 Step 3. Install Device Drivers . . . . . . . 110
43
Step 4. Configure the Autoloader to (Host) . . . . . . . . . . Step 5. Update Firmware . . . My Support . . . . . . . Via Serial Port . . . . . . Via RMU . . . . . . . . Via SCSI / Fibre . . . . . Step 6. Register for My Support .
the Server . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . .
110 111 111 111 118 118 121 123 123 124 125 125 125 126 126 127 128 128 129 130 130 131 132 133 134 134 135 136 137 137 138 138 139 139 140 140 141 142
| | | | | | | | | | | | | | | | | | | | |
| | | | |
Remote Management Unit (RMU) . . . . . . Access Protocol . . . . . . . . . . . . . Login . . . . . . . . . . . . . . . . Help . . . . . . . . . . . . . . . . Quick Status . . . . . . . . . . . . . . Status Icons . . . . . . . . . . . . . Information Menu . . . . . . . . . . . . Autoloader (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Drive (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Status Menu . . . . . . . . . . . . . . Autoloader (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Media (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Configuration Menu . . . . . . . . . . . Device (Model L28/L38/L3H) . . . . . . . Device (Model F28/F38/F3H) . . . . . . . Network (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . User (Models L28/L38/L3H and F28/F38/F3H) RTC (Models L28/L38/L3H and F28/F38/F3H) Log (Models L28/L38/L3H and F28/F38/F3H) Event Notification (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Reset (Models L28/L38/L3H and F28/F38/F3H) Maintenance Menu . . . . . . . . . . . Operations (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . General Diagnostic (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Advanced Diagnostic (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . Firmware (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Reset (Models L28/L38/L3H and F28/F38/F3H) Logs Menu . . . . . . . . . . . . . . Loader (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Drive (Models L28/L38/L3H and F28/F38/F3H) . . . . . . . . . . . . Logout . . . . . . . . . . . . . . . Media . . . . . . . . . . . Data Cartridge . . . . . . . . . Cleaning Cartridge . . . . . . . Bar Code Label . . . . . . . . . Guidelines for Using Bar Code Labels Setting the Write-Protect Switch . . . Handling Cartridges . . . . . . . Provide Training . . . . . . .
Ensure Proper Packaging . . . . . . . . Provide Proper Acclimation and Environmental Conditions . . . . . . . . . . . . . Perform a Thorough Inspection . . . . . . Handle the Cartridge Carefully . . . . . . Examples of Cartridge Problems . . . . . . Environmental and Shipping Specifications for Tape Cartridges . . . . . . . . . . . . Repositioning or Reattaching a Leader Pin . . . Repositioning a Leader Pin . . . . . . . . Reattaching a Leader Pin . . . . . . . . Disposing of Tape Cartridges . . . . . . . . Ordering Media Supplies . . . . . . . . . Ordering Bar Code Labels . . . . . . . .
148 149 149 150 150 151 152 152 154 158 159 160
44
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Menus
The Menus chapter gives information on access protocol for the OCP, RMU, and serial communication, describes the components of the Operator Control Panel (OCP), and gives instructions on how to use the Autoloaders menus via the OCP. v Online Menu on page 49 v Model L28/L38/L3H (SCSI Drive) Offline Menu on page 55 v Model F28/F38/F3H (Fibre Channel Drive) Offline Menu on page 75
Access Protocol
All three Autoloader user interfaces (OCP, RMU, and serial) can simultaneously be active on the lowest level (Information only). v RMU: Standard user v OCP: Online v Serial: lgo (logout) However, only one of the three interfaces can be active at any one time on the Administrator or Service levels (RMU and serial) or at the Offline level (OCP). The other two can remain active on the lowest level. If an attempt to login is made on either of the other two while the third has the highest level access, an Already Reserved message is displayed. The RMU will only allow access by a Standard user at the login panel. For best results: v If communicating via the OCP, return to the Home Screen before attempting to communicate via the RMU or serial port. v If communicating via the RMU, log out before attempting to communicate via the OCP or serial port. v If communicating via the serial port, log out before attempting to communicate via the OCP or RMU
45
| |
v LEDs: 1 READY/ACTIVITY (green) Turns on any time the Autoloader is powered on and able to function. This LED should blink whenever there is Autoloader or tape drive activity. 2 CLEAN DRIVE (amber) Turns on when the tape drive needs to be cleaned. This LED will turn off after the drive is cleaned. 3 MEDIA ATTENTION (amber) Turns on when a media failure occurs. This LED will turn off when all defective, marginal, or invalid cartridges have been exported from the Autoloader. 4 ERROR (red) Turns on when there is an unrecoverable tape drive or Autoloader failure. This LED will turn on at the same time the error message is displayed on the screen and will remain on until the error condition is corrected. v 5 OCPs Display Consists of two lines with 16 characters per line. It displays actions and status information, menu items or error messages. v Buttons 6 CANCEL - Used to return to the Home Screen from any menu screen. - Used to return to the corresponding menu screen from any menus commands screens. 7 PREVIOUS - Used to move back from one menu screen to the previous menu screen.
46
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0215
- Used to move back from one command screen to the previous command screen within the same menu. 8 NEXT - Used to move forward from one menu screen to the next menu screen. - Used to move forward from one command screen to the next command screen within the same menu. 9 ENTER - Used to access the first corresponding command screen from any menu screen . - Used to initiate the corresponding operation from any menus command screens .
Power On Display
When the Autoloader powers on, or resets, it goes through several Power On Self Tests (POST). POST are internally controlled processes that allow the Autoloader to initialize. While these processes are running, the OCP will display appropriate information to keep the user informed of the Autoloaders status.
Home Screen
The Home Screen displays the Autoloaders current status of the drive (Drive empty or Drive ready) on the top line and the current cartridge inventory and operating mode on the bottom line.
The inventory status characters will be represented as follows on the second line of the display: v Slot Empty - A dash character (-) will be displayed as a placeholder. (Slot Full The slot number 1 to 8 will be displayed.) v A cartridge that is being loaded, unloaded, imported, exported, or is loaded in the drive, will be represented by the slot number blinking. v A cartridge that has been identified as invalid or faulty (and the amber Media Attention LED is on) will be represented by an exclamation point (!). The current operating mode will be displayed on the second line. The message varies, depending on the Autoloaders mode of operation: v If the Autoloader is operating in sequential access mode or automatic mode (the default mode), SEQ displays. If a library command is sent by the host and received by the Autoloader, SEQ disappears from the display. v If the Autoloader is operating in random access mode, nothing displays. If the drive detects a write-protected media, the OCP displays WP on the bottom line of the display indicating a write-protected media is loaded in the drive. As soon as the write-protected media is ejected, WP is replaced by the current operating mode. For more information on write-protected media, see Setting the Write-Protect Switch on page 147. To return to the Home Screen, perform one of the following:
Operator Guide: Menus
| | | | |
47
v Suspend all activity on the OCP for one and a half minutes. v Press the OCPs Cancel button from the top level of the current menu.
48
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Online Menu
| | |
HOME (ONLINE) STATUS (INV. STATUS)
ANY KEY
After powering on the Autoloader, the Online Menu is available. The Online Menu contains the Information Menu and Go Offline.
ALREADY RESERVED
> >
DRIVE INFO. (INV. STATUS) GO ONLINE (INV. STATUS)
| | |
Information Menu
The Information Menu contains commands that will display such things as Autoloader and drive serial numbers, model numbers, firmware levels, and error logs. To navigate to the Information Menu from the Home Screen: v Press any button (Cancel, Previous, Next, or Enter) on the OCP.
a67s0221
49
LOADER INFO
LOADER INFO contains the information that relates specifically to the Autoloader.
> >
SERIAL NUMBER 0123456789
> >
MACHINE TYPE 1234
> >
MODEL NUMBER 123
> >
CYCLE COUNT XXX
> >
ERROR LOG TOTAL XXX
> >
BARCODE READER (BCR STATUS)
>
Note: Enter the information in this menu on the Autoloader Configuration Form on page 251. To 1. 2. 3. 4. access the LOADER INFO menu using the OCP: Navigate to the Information Menu (see Information Menu on page 49). Press Enter to access the LOADER INFO screen. Press Enter to access the first item in the LOADER INFO menu. Press Next or Previous to navigate through the following menu items: v FIRMWARE REV - the current Autoloader firmware revision level v SERIAL NUMBER - this number should match the serial number on the label located in the lower right corner on the Autoloaders front panel v MACHINE TYPE - 3581 v MODEL NUMBER - either L28/L38/L3H (LVD SCSI drive) or F28/F38/F3H (Fibre Channel drive) v CYCLE COUNT - the number of times the cartridge carousel has made a complete cycle.
| |
50
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
v ERROR LOG - displays the error code (XX YY ZZ) and time the error occurred (ddd.hh.mm.ss.tt)
X
ERROR: XX XX YY ZZ
Figure 29. Information Menu Error Log for the Autoloader command
After navigating to ERROR LOG using the OCP: a. Press Enter to access the ERROR: XX screen and to display the error code (XX YY ZZ). b. Press Previous to scroll through each previous error entry in the log. | c. Press Enter to display EVENT TIME: X of the error (ddd.hh.mm.ss.tt). d. Press Previous to scroll through other previous event times. e. Press Cancel: One time to return to the corresponding error entry. Two times to return to the ERROR LOG screen. Three times to return to the LOADER INFO screen. Four times to return to the Information Menu screen. Five times to return to the Home Screen. v BARCODE READER Press Enter to display the line LOADER BCR LAB X (X = library tape location). If the tape has a barcode, it will be displayed on the next nine. Otherwise, the second line will be blank. NO BCR FUNCTION will be displayed if the BCR: - Is not installed - OR - Is installed but not initiated via the Configuration Menu BCR PRESENT will be displayed if the BCR is installed and initiated via the Configuration Menu Press Cancel as many times as necessary to exit and return to the Home Screen.
| | | |
| | |
a67s0188
51
DRIVE INFO
DRIVE INFO contains the following information that relates specifically to the Autoloaders drive.
>
PRODUCT REV 1234
> >
SERIAL NUMBER 0123456789
> >
SCSI EVT LOG
> >
ERROR LOG
>
Note: Enter the information in this menu on the Autoloader Configuration Form on page 251. To access the DRIVE INFO menu using the OCP: 1. 2. 3. 4. 5. Navigate to the Information Menu (see Information Menu on page 49). Press Enter. Press Next to access the DRIVE INFO screen. Press Enter to access the first menu item in the DRIVE INFO menu. Press Next or Previous to navigate through the following menu items: v PRODUCT REV. - the current drive firmware revision level v SERIAL NUMBER - the drive serial number v SCSI EVT LOG - displays the error number (XX YY ZZ VV NN) and the time the error occurred (dddd:hh:mm:ss:tt)
X
Figure 31. Information Menu SCSI Event Log for the drive command
After navigating to SCSI EVT LOG using the OCP: a. Press Enter to access the ERROR LOG X screen and to display the error number (XX YY ZZ VV NN). b. Press Enter to display the time the error occurred (dddd:hh:mm:ss:tt).
52
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0 173
ERROR LOG X XX YY ZZ VV NN
> >
c. Press Cancel: One time to return to the corresponding error entry. Two times to return to the SCSI EVT LOG screen. Press Next to access the next menu item. Three times to return to the DRIVE INFO screen. Four times to return to the Information Menu screen. Five times to return to the Home Screen. v ERROR LOG - displays the error number (XX YY ZZ VV NN) and the time the error occurred (dddd:hh:mm:ss:tt)
X
ERROR LOG
Figure 32. Information Menu Error Log for the drive command
After navigating to ERROR LOG using the OCP: a. Press Enter to access the ERROR LOG X screen and to display the error number (XX YY ZZ VV NN). b. Press Enter to display the time the error occurred (dddd:hh:mm:ss:tt). c. Press Cancel: v One time to return to the corresponding error entry. v Two times to return to the ERROR LOG screen. Press Next to access the next menu item. v Three times to return to the DRIVE INFO screen. v Four times to return to the Information Menu screen. v Five times to return to the Home Screen.
Go Offline
Password protection for going Offline to the Autoloader via the OCP can be turned OFF (default setting) or ON.
| |
a67s0187
ERROR LOG X XX YY ZZ VV NN
> >
53
| |
54
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
> >
> >
> >
(+) >
(+) >
>
>
>
> LOADER
DIAGNOSTIC (INV. STATUS)
> >
DRIVE INFO. (INV. STATUS) IMPORT (INV. STATUS)
> >
> >
CHANGE SCSI I.D. (INV. STATUS) DRIVE DIAGNOSTIC (INV. STATUS)
> >
>
EXPORT (INV. STATUS)
> >
SCSI SPEED AUTOMATIC
> >
>
> >
LOAD CARTRIDGE (INV. STATUS)
> >
DRIVE FW UPGRADE FROM FMR TAPE
> >
UNLOAD CARTRIDGE (INV. STATUS)
> >
CHANGE LDR MODE AUTOMATIC
> >
CLEAN DRIVE (INV. STATUS) LOOP MODE OFF
> >
> >
RE-INVENTORY (INV. STATUS)
> >
AUTOLOAD MODE OFF
>
> >
NET PARAMETER (INV. STATUS)
> >
BARCODE READER on / off
> >
PROTECTION MODE OFF
> >
SERIAL NUMBER 0123456789
>
| | | | | | | | | |
Information Menu
See Information Menu on page 49.
Commands Menu
To navigate to the Commands Menu from the Home Screen using the OCP: v Press any button (Cancel, Previous, Next, or Enter) on the OCP to display the Information Menu screen. v Press Next to display the Commands Menu screen.
Operator Guide: Menus
55
| | | | | |
BULK EXCHANGE
BULK EXCHANGE enables the user to import or export all cartridges. Operation begins with Slot 1. If a cartridge is available, it will be exported. It is up to the user to import a new cartridge or to move to Slot 2. The same procedure repeats for the remainder of the eight slots.
Legend Cancel Enter > Previous > Next
X
| | | | | | | | | | | | | | | | |
To access BULK EXCHANGE using the OCP: 1. 2. 3. 4. Navigate to the Commands Menu (see Commands Menu on page 55). Press Enter to access BULK EXCHANGE. Press Enter to initiate the importing and/or exporting of cartridges. When the I/O Door opens, remove the ejected cartridge or proceed to the next step.
5. Do one of the following: v Insert another cartridge gently pushing the cartridge through the I/O Door until the cartridge can be pushed no farther. v Press Enter to export the next cartridge. v Press Cancel to terminate BULK EXCHANGE. 6. When all cartridges have been imported and/or exported, the Autoloader will return to the Home Screen.
IMPORT
The IMPORT command allows the user to insert and choose a destination slot for a cartridge in the Autoloader.
a67s0219
DOOR STATUS
| | | | | | | |
To 1. 2. 3. 4.
access IMPORT using the OCP: Navigate to the Commands Menu (see Commands Menu on page 55). Press Enter then Next to access IMPORT. Press Enter to display the IMPORT TO: screen. Use the Next and Previous to select the number of the slot to which the cartridge is to be imported. (Only those slots that are empty will be available for selection.) 5. Press Enter to initiate the procedure.
56
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0171
| | | | | | | | | | |
6. When the I/O Door opens, insert a cartridge. The Autoloader will import the cartridge, close the I/O Door, and insert the cartridge into the selected slot. 7. Repeat Steps 4 through 6 until all cartridges have been imported. 8. When the last cartridge has been inserted into its slot, press Cancel to return to the IMPORT screen. 9. Press Cancel to prompt the BCR (if installed) to re-inventory all cartridges and return to the Home Screen.
EXPORT
The EXPORT command allows the user to remove a cartridge from a selected slot in the Autoloader.
EXPORT STATUS
DOOR STATUS
| | |
To access EXPORT using the OCP: 1. Navigate to the Commands Menu (see Commands Menu on page 55). 2. Press Enter then Next or Previous, as necessary, until EXPORT is displayed. 3. Press Enter to display the EXPORT FROM: screen. 4. Use the Next and Previous to select the number of the slot from which the cartridge is to be exported. (Only those slots containing cartridges will be available for selection.) 5. Press Enter to initiate the procedure. 6. When the I/O Door opens, remove the cartridge. 7. Press Enter. 8. To export another cartridge, repeat Steps 4 through 7 until all cartridges have been exported. Otherwise, proceed to Step 9. 9. Press Cancel: v One time to return to the EXPORT SLOT x screen. v Two times to prompt the BCR (if installed) to re-inventory all cartridges and return to the Home Screen
57
a67s0184
LOAD CARTRIDGE
The LOAD CARTRIDGE command allows the user to insert a selected cartridge in the Autoloader into the drive.
LOAD STATUS
ANY KEY
UNLOAD STATUS
ANY KEY
Figure 37. Commands Menu LOAD CARTRIDGE and UNLOAD CARTRIDGE commands
| |
To access LOAD CARTRIDGE using the OCP: 1. Navigate to the Commands Menu (see Commands Menu on page 55). 2. Press Enter then Next or Previous, as necessary, until LOAD CARTRIDGE is displayed. 3. Press Enter to display the LOAD CARTRIDGE SLOT # screen. 4. Use Next and Previous to select the number of the slot of the cartridge to be loaded into the drive. 5. Press Enter to initiate the procedure. 6. When the cartridge has been loaded into the drive, the Autoloader will return to the Home Screen.
UNLOAD CARTRIDGE
The UNLOAD CARTRIDGE allows the user to remove a cartridge from the drive and return it to its home slot (see Figure 37). To access UNLOAD CARTRIDGE using the OCP: 1. Navigate to the Commands Menu (see Commands Menu on page 55). 2. Press Enter then Next or Previous, as necessary, until UNLOAD CARTRIDGE is displayed. 3. Press Enter to unload the cartridge currently in the drive. 4. When the cartridge has been returned to its home slot, the Autoloader will return to the Home Screen.
| |
CLEAN DRIVE
When the amber CLEAN DRIVE LED on the OCP turns on (the second LED from the left), the drive must be cleaned to ensure optimum drive performance and to safeguard your media. The CLEAN DRIVE command allows the user to initiate a cleaning of the drive. The user will be prompted to insert a cartridge in the I/O Door if a cleaning cartridge does not currently reside in the Autoloader.
58
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0185
NO
Full Carousel?
YES
IMPORT STATUS
DOOR STATUS
INSERT CARTRIDGE SLOT n
DOOR STATUS
CART. INSERTED
Cleaning Cartridge?
YES
NO
DOOR STATUS
REMOVE CARTRIDGE PRESS ENTER
DOOR STATUS
| |
To access CLEAN DRIVE using the OCP: 1. Navigate to the Commands Menu (see Commands Menu on page 55). 2. Press Enter then Next or Previous, as necessary, until CLEAN DRIVE is displayed. 3. Press Enter.
a67s0172
59
4. If there are eight cartridges (all slots are full) in your Autoloader, press Cancel to return to the Commands Menu screen and EXPORT one data cartridge. If there are less than eight cartridges (all slots are not full) in your Autoloader, proceed to the next step. 5. When the I/O Door opens, insert a cleaning cartridge. 6. When the cleaning is complete, remove the ejected cleaning cartridge from the I/O Door. 7. Press Enter to return to the Home Screen.
RE-INVENTORY
The RE-INVENTORY command allows the BCR (if installed) to scan all cartridges in the Autoloader to update the cartridge inventory.
Legend Cancel Enter > Previous > Next
X
INVENTORY STATUS
ANY KEY
| |
To access RE-INVENTORY using the OCP: 1. Navigate to the Commands Menu (see Commands Menu on page 55). 2. Press Enter then Next or Previous, as necessary, until RE-INVENTORY is displayed. 3. Press Enter to initiate the inventory. 4. The Autoloader will return to the Home Screen and the updated inventory will be displayed on the second line.
Configuration Menu
The Configuration Menu allows the administrator to setup or change SCSI IDs, SCSI speed, operating mode, network parameters, as well as, initializing the BCR. To navigate to the Configuration Menu from the Home Screen using the OCP: v Press any button (Cancel, Previous, Next, or Enter) on the OCP to display the Information Menu screen. v Press Next until the Configuration Menu screen displays.
RESET
RESET restarts the Autoloader and is used when initiating configuration changes.
Legend Cancel Enter > Previous > Next
X
To 1. 2. 3. 4.
access RESET using the OCP: Navigate to the Configuration Menu (see Configuration Menu). Press Enter to access RESET. Press Enter to initiate the reset. When the reset is complete, the OCP will display the Home Screen.
60
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0174
RESET STATUS
a67s0186
CHANGE SCSI ID
CHANGE SCSI ID allows the user to set a new value for SCSI IDs. The SCSI default ID is 2.
Legend Cancel Enter > Previous > Next
X
To access CHANGE SCSI ID using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). | | 2. Press Enter then Next or Previous, as necessary, until CHANGE SCSI ID is displayed. 3. Press Enter to display the CHANGE SCSI ID Drive (XX) screen. 4. Press Enter to display the CHANGE SCSI ID New SCSI ID: screen. 5. Use Next and Previous to select each digit in the new ID. After selecting each number, press Enter on the OCP to initiate the selected number and move to the next digit in the ID. 6. After all digits have been selected and initiated, cycle power by turning the Autoloader off then on again. After the power has cycled, the Home Screen will be displayed.
SCSI SPEED
Attention: SCSI SPEED is supported by certain host bus adapters. To determine if your adapter supports SCSI SPEED: v Refer to the documentation for your server (host). v Visit the web at http://www.ibm.com/storage/support/lto.
To 1. 2. 3.
access SCSI SPEED using the OCP: Navigate to the Configuration Menu (see Configuration Menu on page 60). Press Enter then Next or Previous, as necessary, until SCSI SPEED is displayed. Press Enter to display the CHANGE SPEED TO: screen.
4. Use Next and Previous to select the new SCSI speed: v 80 MB/s v AUTO (variable speed; maximum speed allowed at the time) 5. Press Enter to initiate the new speed and cycle power by turning the Autoloader off then on again. After the power has cycled, the Home Screen will be displayed.
a67s0193
61
a67s0189
| |
To access CHANGE LDR MODE using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, until CHANGE LDR MODE is displayed. 3. Press Enter to display the CHANGE LDR MODE TO: screen. 4. Use Next and Previous to select the new mode (Automatic, Sequential, or Random). 5. Press Enter to initiate the new mode. 6. Press Cancel: v One time to return to the Configuration Menu screen. v Two times to return to the Home Screen. Automatic Mode: Automatic mode is the default setting and allows the Autoloader to switch between sequential and random modes depending on the SCSI command received. In automatic mode, sequential mode is activated when the Autoloader is powered on. When the Autoloader receives a MOVE MEDIUM, READ ELEMENT STATUS, or an INITIALIZE ELEMENT STATUS command, sequential mode is disabled and random mode becomes active. The Autoloader will switch back to sequential mode with every OCP initiated LOAD or UNLOAD command. Sequential Mode: In sequential mode, the Autoloaders firmware predefines the selection of the cartridges. After initialization, the firmware causes the Autoloader to select the first available cartridge found (counting from 1 through 8) for loading into the drive. If AUTOLOAD MODE (see AUTOLOAD MODE on page 63) is set to ON, the first cartridge will load automatically. Otherwise, the OCPs LOAD CARTRIDGE command must be executed. After the servers (hosts) application software fills this cartridge with data and issues an UNLOAD command, the Autoloader returns the cartridge to its storage slot and loads the next cartridge in order. Empty storage slots are ignored. The Autoloader continues this process until all cartridges have been filled with data.
62
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0190
Note: While in sequential mode, the Autoloaders robotics are not logically connected to the SCSI bus and do not respond to SCSI commands. Associated with sequential mode are LOOP MODE and AUTOLOAD MODE. See LOOP MODE and AUTOLOAD MODE for more information. Random Mode: In random mode, the Autoloader allows the servers (hosts) application software to select any data cartridge in any order.
LOOP MODE
LOOP MODE can be used with sequential mode. Sequential mode with LOOP MODE ON loads the cartridge in slot 1 after the cartridge in slot 8 has been filled and sent back to its home slot. This allows endless backup operations without user interaction.
Legend Cancel Enter > Previous > Next
X
| |
To access LOOP MODE using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, until LOOP MODE is displayed. 3. Press Enter to display the LOOP MODE CHANGE TO: screen. 4. Use Next and Previous to select ON or OFF. 5. Press Enter to initiate the new mode. 6. Press Cancel: v One time to return to the Configuration Menu screen. v Two times to return to the Home Screen.
AUTOLOAD MODE
AUTOLOAD MODE can also be used with sequential mode. Sequential mode with AUTOLOAD MODE ON loads the first cartridge automatically if the Autoloader powers on with an empty drive.
Legend Cancel Enter > Previous > Next
X
To access AUTOLOAD MODE on the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). | | 2. Press Enter then Next or Previous, as necessary, until AUTOLOAD MODE is displayed. 3. Press Enter to display the AUTOLOAD MODE CHANGE TO: screen. 4. Use Next and Previous to select ON or OFF. 5. Press Enter to initiate the new mode.
Operator Guide: Menus
a67s0192
a67s0191
63
6. Press Cancel: v One time to return to the Configuration Menu screen. v Two times to return to the Home Screen.
NET PARAMETER
Turn NET PARAMETER ON when an RMU is installed on the Autoloader. This menu item also allows the user to: v Turn DHCP (Dynamic Host Configuration Protocol) on or off v Set or change the Autoloaders IP Address v Set or change the Autoloaders Gateway Address v Set or change the Autoloaders Network Mask Address
NETWORK OFF
> >
X
DHCP OFF
> >
X
IP ADDRESS XXX.YYY.ZZZ.VVV
> >
GATEWAY ADDRESS XXX.YYY.ZZZ.VVV
> >
NETMASK XXX.YYY.ZZZ.VVV
NETMASK XXX.YYY.ZZZ.VVV
| |
To access NET PARAMETER using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, until NET PARAMETER is displayed. a. Press Enter to display the NETWORK screen. Current status is displayed b. Press Enter to display the NETWORK CHANGE TO: screen c. Use Next and Previous to select ON or OFF. d. Press Enter to initiate the change and return to the NETWORK screen. 3. Press Next to display the DHCP screen. Current status is displayed. a. Press Enter to display the DHCP CHANGE TO: screen. b. Use Next and Previous to select ON or OFF. c. Press Enter to initiate the change and return to the DHCP screen. 4. Press Next to display the IP ADDRESS screen. The current IP Address is displayed. a. Press Enter to display the CHANGE IP ADDRESS screen.
64
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0176
| |
| |
| | | | | | |
b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the IP ADDRESS screen. 5. Press Next to display the GATEWAY ADDRESS screen. The current Gateway Address is displayed. a. Press Enter to display the CHANGE GATEWAY screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the GATEWAY ADDRESS screen. 6. Press Next to display the NETMASK screen. The current Netmask Address is displayed. a. Press Enter to display the CHANGE NETMASK screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the NETMASK screen. 7. Press Cancel: v One time, and the message CYCLE POWER FOR NEW NETPARAM is displayed. v Two times to return to the NET PARAMETER screen. v Three times to return to the Configuration Menu screen. v Four times to return to the Home Screen.
BARCODE READER
Turn BARCODE READER ON when a BCR is installed on the Autoloader.
| |
| | | | | |
To access BARCODE READER using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, until BARCODE READER is displayed. a. Press Enter to display the BARCODE READER CHANGE TO: screen b. Use Next and Previous to select ON or OFF. c. Press Enter to initiate the change. If ON was selected, the barcode reader will inventory the cartridges in the autoloader. 3. Press Cancel: v One time to return to the Barcode Reader screen. v Two times to return to the Configuration Menu screen. v Three times to return to the Home screen.
a67s0231
65
PROTECTION MODE
| | Turn PROTECTION MODE ON to initiate a password protected login. Leave PROTECTION MODE OFF (default setting) to allow going offline without a password.
X
PROTECTION ON
PROTECTION MODE ON
a67s0244
| | | | | | | | | | | | | | | | | | | | | | | | | | | |
Turning PROTECTION MODE ON: To activate password protection on the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, to access PROTECTION MODE. a. Press Enter to display the PROTECTION MODE CHANGE TO: screen. b. Use Next or Previous to select ON. c. Press Enter to initiate the change. d. Enter a new PIN (password) using Next and Previous. After selecting each digit, press Enter to initiate the entry and move to the next digit. e. Press Enter to confirm the new PIN (password). PROTECTION ON is displayed. f. Press Enter to return to the PROTECTION MODE screen. 3. Press Cancel: v One time to return to the Configuration Menu. v Two times to return to the Home screen. Turning PROTECTION MODE OFF: To deactivate password protection on the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, to access PROTECTION MODE. a. Press Enter to display the PROTECTION MODE CHANGE TO: screen. b. Use Next or Previous to select OFF. c. Press Enter to initiate the change. The message Disable protect are you sure? is displayed. d. Press Enter for YES or Cancel for NO. e. Press Enter to return to the PROTECTION MODE CHANGE TO: screen. 3. Press Cancel: v One time to return to the PROTECTION MODE screen.
66
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| |
v Two times to return to the Configuration Menu screen. v Three times to return to the Home screen.
SERIAL NUMBER
This menu item allows the user to change the serial number displayed by the OCP. This item should be utilized when a replacement Autoloader is being installed. The serial number of the replacement Autoloader should be changed to the serial number of the original Autoloader for warranty purposes.
Legend Cancel Enter
To access SERIAL NUMBER via the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, until SERIAL NUMBER is displayed. 3. Press Enter to display the CHANGE SER NUM screen. 4. Use Next and Previous to select each digit in the new serial number. Press Enter to initiate each new digit and move to the next digit to be changed. The Autoloaders serial number is seven digits in length; therefore, the first three digits of the serial number should be entered as 000. 5. Press Cancel to return to the SERIAL NUMBER screen.
Diagnostic Menu
To navigate to the Diagnostic Menu from the Home Screen using the OCP: v Press any button (Cancel, Previous, Next, or Enter) to display the Information Menu screen. v Press Next until the Diagnostic Menu screen displays.
LOADER DIAG
The LOADER DIAG menu allows an Administrator to run a system test and a library verify test. To access the LOADER DIAG menu: 1. Navigate to the Diagnostic Menu (see Diagnostic Menu). 2. Press Enter to access the LOADER DIAG menu. LIBRARY VERIFY: Note: LIBRARY VERIFY requires a blank or scratch cartridge. This test will write and read data on the cartridge. DO NOT USE a cartridge containing valuable data. When Library Verify is selected, the following actions take place: 1. The Autoloader ensures that all Autoloader hardware is functional. 2. The Autoloader ensures it can communicate with the drive over the RS422. 3. If the drive has a cartridge loaded, the Autoloader performs one of the following:
Operator Guide: Menus
a67s0248
67
4. 5. 6.
7. 8. 9. 10.
11.
v Moves the cartridge to its home slot. v Moves the cartridge to the I/O Door and asks the user to remove it, if the home slot is unknown If there is a cartridge in the I/O Door, the Autoloader prompts the user to remove it. Verify that the cartridge has been removed before proceeding. The Autoloader prompts the user to put a scratch cartridge known to be in good working condition into the I/O Door. When the scratch cartridge has been loaded, if the BCR is installed, it will read the bar code label on the scratch cartridge and save it for later comparison. The Autoloader moves the scratch cartridge to the drive. The Autoloader tells the drive to run a Fast Read/Write Test which includes a write/read/verify test on the tape. When the drive test is done, the Autoloader test tells the drive to eject the tape, then moves it back to the I/O Door. If a BCR is installed, when the scratch cartridge has been moved back to the I/O Door, it reads the bar code label again and compares it to what was recorded earlier. The Autoloader will prompt the user to remove the scratch cartridge from the I/O Door.
If any error is encountered during the Library Verify Test, see Troubleshooting on page 163 for help in diagnosing the problem.
Legend Cancel Enter > Previous > Next
X
To 1. 2. 3.
access LIBRARY VERIFY using the OCP: Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). Press Enter to access the LOADER DIAG menu. Press Enter to access LIBRARY VERIFY.
4. Press Enter to begin the verification. 5. If a cartridge is in the drive: v The cartridge will be moved to its home slot. v The cartridge will be ejected through the I/O Door if the home slot is unknown and the user will be prompted to remove the cartridge. 6. When prompted, insert a scratch cartridge through the I/O Door. 7. When the test is complete and when prompted, remove the scratch cartridge when ejected through the I/O Door. 8. If an error occurred, the FAILED screen will display. Troubleshoot the problem (see Troubleshooting on page 163). If no error occurred, the PASSED screen will display. Proceed to the next step. 9. Press Cancel: v One time to return to the LOADER DIAG screen. v Two times to return to the Diagnostic Menu screen. v Three times to return to the Home Screen.
68
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0230
LIBRARY STATUS
SYSTEM TEST: Note: SYSTEM TEST requires at least one data cartridge. The cartridges are loaded and unloaded but no data is written on the cartridges. SYSTEM TEST allows the user to select the number of cycles (270, 540, 1080, ENDLESS) the Autoloader will run while performing a system diagnostic.
Legend Cancel Enter > Previous > Next
X
To access SYSTEM TEST using the OCP: 1. Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). 2. Press Enter to access the LOADER DIAG menu. 3. Press Enter then Next to access SYSTEM TEST. 4. Press Enter to display the SELECT CYCLES screen. 5. Use Next and Previous to select the number of cycles to run the test (270, 540, 1080, or ENDLESS). 6. Press Enter to initiate the selection and begin the test. At the end of the test the DRIVE EMPTY screen will display. 7. Press Cancel: v One time to return to the LOADER DIAG screen. v Two times to return to the Diagnostic Menu screen. v Three times to return to the Home Screen.
69
a67s0177
SELECT CYCLES nn
DRIVE DIAG
The DRIVE DIAG menu allows the user to run diagnostic tests on the drive.
DRIVE DIAG. (INV. STATUS)
X
TEST STATUS
> >
HEAD TEST (INV. STATUS) TEST STATUS PASSED 00 00 FINISH DRV TEST
> >
MEDIA TEST (INV. STATUS) TEST STATUS PASSED 00 00 FINISH DRV TEST
> >
NORMAL R/W TEST (INV. STATUS) TEST STATUS PASSED 00 00 FINISH DRV TEST
> >
FAST R/W TEST (INV. STATUS) TEST STATUS PASSED 00 00 FINISH DRV TEST
> >
SCSI/FC WRAPTEST (INV. STATUS)
TEST STATUS
> >
RECALIBRATION
INSERT CARTRIDGE SLOT REMOVE CARTRIDGE PRESS ENTER DRIVE EMPTY
> >
PRESERVE DUMP
DIAGNOSIS... (GRN LED FLASHES) DRIVE EMPTY
Note: The format of a drive error code reported on the OCP is 0x00. The leading and trailing zeros are ignored. To access the DRIVE DIAG menu using the OCP: 1. Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). 2. Press Enter then Next to access the DRIVE DIAG menu. PWR ON SELF TEST: The Power On Self Test (POST) tests the drives initialization process. The OCPs green LED will blink during this initialization process. When the drive completes the Power On Self Tests (POST), the green LED will stop blinking. The POST runs each time the Autoloader is powered on as well as whenever it is activated via this menu item. To access PWR ON SELF TEST using the OCP:
70
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0228
Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). Press Enter then Next to access the DRIVE DIAG menu. Press Enter to access PWR ON SELF TEST. Press Enter to initiate the test. If the test FAILED, troubleshoot the problem (see Troubleshooting on page 163). If the test PASSED, press Enter to return to the PWR ON SELF TEST screen. 6. Press Cancel to return to the Home Screen. 1. 2. 3. 4. 5. HEAD TEST: The Head Test performs diagnostics on difficult head patterns and determines if the head is functioning properly. To 1. 2. 3. 4. 5. access HEAD TEST using the OCP: Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). Press Enter then Next to access the DRIVE DIAG menu. Press Enter then Next to access HEAD TEST. Press Enter to initiate the test. When prompted and the I/O Door opens, insert a scratch cartridge. When test is complete, remove scratch cartridge from the I/O Door when prompted. 6. If the test FAILED, troubleshoot the problem (see Troubleshooting on page 163). If the test PASSED, press Enter to return to the PWR ON SELF TEST screen. 7. Press Cancel to return to the Home Screen. MEDIA TEST: The Media Test verifies whether a suspect tape cartridge and its magnetic media are acceptable. Attention: To 1. 2. 3. Data on the suspect tape will be overwritten during this test.
| |
access MEDIA TEST using the OCP: Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). Press Enter then Next to access the DRIVE DIAG menu. Press Enter then Next or Previous, as necessary, until MEDIA TEST is displayed. 4. Press Enter to initiate the test. 5. When prompted and the I/O Door opens, insert the suspect cartridge. When test is complete, remove the cartridge from the I/O Door when prompted. 6. If the test FAILED, troubleshoot the problem (see Troubleshooting on page 163). If the test PASSED, press Enter to return to the PWR ON SELF TEST screen. 7. Press Cancel to return to the Home Screen. NORMAL R/W TEST: The Normal Read/Write Test performs a load operation, a write/read test, and an unload operation. The Normal Read/Write Test is more comprehensive and longer in duration than the Fast Read/Write Test. To 1. 2. 3. access NORMAL R/W TEST using the OCP: Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). Press Enter then Next to access the DRIVE DIAG menu. Press Enter then Next or Previous, as necessary, until NORMAL R/W TEST is displayed.
Operator Guide: Menus
| |
71
4. Press Enter to initiate the test. 5. When prompted and the I/O Door opens, insert a scratch cartridge. When test is complete, press Enter and remove the scratch cartridge from the I/O Door when ejected. 6. If the test FAILED, troubleshoot the problem (see Troubleshooting on page 163). If the test PASSED, press Enter to return to the Home Screen. FAST R/W TEST: The Fast Read/Write Test performs a load operation, a write/read test, and an unload operation. To access FAST R/W TEST using the OCP: 1. Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). | | 2. Press Enter then Next to access the DRIVE DIAG menu. 3. Press Enter then Next or Previous, as necessary, until FAST R/W TEST is displayed. 4. Press Enter to initiate the test. 5. When prompted and the I/O Door opens, insert a scratch cartridge. When test is complete, press Enter and remove the scratch cartridge from the I/O Door when ejected. 6. If the test FAILED, troubleshoot the problem (see Troubleshooting on page 163). If the test PASSED, press Enter to return to the Home Screen. SCSI / FIBRE WRAP TEST: The wrap test causes the Autoloaders drive to perform one of the following: v A check of the SCSI circuitry from and to the SCSI connector (Model L28/L38/L3H) v A check of the Fibre Channel circuitry from and to the Fibre Channel connector or fiber cable (Model F28/F38/F3H) To run the wrap test, determine whether your Autoloader uses a SCSI (Model L28/L38/L3H) or Fibre Channel (Model F28/F38/F3H) interface, then choose one of the following procedures. Running an LVD SCSI Wrap Test: To run a wrap test on an LVD SCSI system, complete the following steps: 1. Disconnect the SCSI cable on the rear of the Autoloader from the receptacle closest to the server in the SCSI bus. Ensure that the terminator or SCSI cabling to the terminator at the end of the bus remains on the other connector. 2. Attach the LVD SCSI wrap tool (see Step 2. Verify the Shipment Inventory on page 19) to the connector where the SCSI cable was just removed. 3. Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). 4. Press Enter then Next to access the DRIVE DIAG menu. 5. Press Enter then Next or Previous, as necessary, until SCSI WRAP TEST is displayed. 6. Press Enter to initiate the test. 7. At the end of the test, the OCP will indicate TEST PASSED or TEST FAILED. v If TEST PASSED is displayed, the Autoloader is functioning properly. If the original problem persists, there is a failure outside the Autoloader or its attachments. Check the SCSI cables, the servers hardware or software (device drivers, etc.).
| | | | | | |
| |
| | | |
72
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| |
v If TEST FAILED is displayed, repeat the test with a different SCSI terminator. If TEST FAILED persists, replace the Autoloader (see Removing/Replacing the Autoloader on page 204). 8. Remove the LVD SCSI wrap tool and restore the original SCSI cable connections. Running an HVD SCSI Wrap Test: There is no HVD SCSI wrap tool available. However, it is important to exercise the LVD SCSI wrap test on the drive to help eliminate it as the failing unit. On Autoloaders with an HVD Converter, complete the following steps: 1. Remove the SCSI cable from the HVD Converter that is attached to the LVD SCSI receptacle on the base unit. Leave the LVD terminator attached to the other LVD SCSI receptacle. 2. Attach the LVD SCSI wrap tool to the connector where the HVD Converter SCSI cable was just removed. 3. Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). 4. Press Enter then Next to access the DRIVE DIAG menu. 5. Press Enter then Next or Previous, as necessary, until SCSI WRAP TEST is displayed. 6. Press Enter or Previous as necessary to initiate the test. 7. If the LVD SCSI wrap indicates TEST FAILED, then replace the Autoloader. See Removing/Replacing the Autoloader on page 204. 8. If the LVD SCSI wrap indicates TEST PASSED, then the problem may be with the HVD Converter, SCSI cable(s), terminator or other hardware/firmware (device driver, etc.) outside the Autoloader or its attachments. 9. Check all SCSI cable connections and terminator for damage or bent pins. Remove the LVD SCSI wrap tool and reattach the HVD Converter SCSI cable to the LVD SCSI receptacle on the Autoloader. If damage or a bent pin was found on the HVD Converter SCSI cable connector, and, if it could not be corrected, replace the HVD Converter. See Removing/Replacing the HVD Converter on page 214. 10. Even if SCSI cable damage or bent pins were not found, try another SCSI cable and terminator and repeat the failing test from the host. 11. If the test still fails, replace the HVD Converter. See Removing/Replacing the HVD Converter on page 214. Running a Fibre Channel Wrap Test: To run a wrap test on a Fibre system, complete the following steps: 1. Disconnect the fiber cable from the connector on the rear panel of the Autoloader. 2. Attach the Fibre wrap tool (see Step 2. Verify the Shipment Inventory on page 19) to the connector where the fiber cable was just removed. 3. Navigate to the Diagnostic Menu (see Diagnostic Menu on page 67). 4. Press Enter then Next to access the DRIVE DIAG menu. 5. Press Enter then Next or Previous, as necessary, until SCSI WRAP TEST is displayed. 6. Press Enter to initiate the test. 7. The OCP will indicate TEST PASSED or TEST FAILED. v If TEST PASSED is displayed, the Autoloader is functioning properly. If the original problem persists, there may be a failure outside the Autoloader or its attachments. Use switch, hub, or other fibre product service guides, as
Operator Guide: Menus
| |
| | |
73
| |
| | | | | | | | | | | | | | | | | | | | | | | | | | |
appropriate, and verify the switch hub configuration, host adapter, host software levels, and other device drivers. v IF TEST FAILED is displayed, replace the Autoloader (see Removing/Replacing the Autoloader on page 204). 8. Remove the fibre wrap tool and restore the original fibre channel connections. RECALIBRATION: Running a Drive Recalibration Test: To run a drive recalibration test, complete the following steps: 1. Navigate to the Diagnostic Menu. 2. Press Enter and then Next to access the DRIVE DIAG menu. 3. Press Enter then press Next until Recalibration is displayed. 4. Press Enter to initiate the test. 5. OCP prompts you to insert a cartridge into Slot 1 through the I/O door. 6. When the calibration diagnostic is complete, remove the cartridge from the I/O door and press Enter. PRESERVE DUMP (LTO-3 only): To aid in failure analysis for LTO-3 tape drives, prior to removing the failing Autoloader and while the power is still enabled to the Autoloader, it is very important to preserve any available drive dump that may be in the active dump area in the drive memory. Running a Preserve Dump: To run a Preserve Dump, complete the following steps: 1. Navigate to the Diagnostic Menu 2. Press Enter and then Next to access the DRIVE DIAG menu. 3. Press Enter then press Next until PRESERVE DUMP is displayed. 4. Press Enter to initiate the test. Note: The OCP display will show Diagnosis.. and OCPs green LED will blink during this process. When the preserve dump is complete, the green LED will stop blinking. 5. Wait until the Home Screen displays Drive empty before removing the drive. 6. When the preserve dump is complete, press Enter to return to the Home Screen.
Go Online
Going online or logging out of the Autoloader will allow only the Information Menu to be displayed. This protects your Autoloader from being reconfigured or the advanced menus being accessed. To go online or logout of the Autoloader using the OCP: 1. Navigate to Go Online. a. From the Home Screen, press any key (Cancel, Previous, Next, or Enter) to access the Information Menu. b. Continue to press Next, as necessary, until Go Online is displayed. 2. Press Enter to complete going online.
74
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| |
ANY KEY
> >
> >
> >
(+) >
(+) >
>
>
LOADER INFO. (INV. STATUS)
>
> >
DRIVE INFO. (INV. STATUS) IMPORT (INV. STATUS)
> >
> >
CHANGE LOOP I.D. (INV. STATUS)
> >
DRIVE DIAG . (INV. STATUS)
> >
EXPORT (INV. STATUS)
> >
FIBRE CHANNEL (NL PORT)
> >
LOAD CARTRIDGE (INV. STATUS)
> >
WW NODE NAME LLLLLLLLLLLLLLL
> >
UNLOAD CARTRIDGE (INV. STATUS)
FIBRE SPEED 2 GB/S
> >
> >
CLEAN DRIVE (INV. STATUS)
> >
DRIVE FW UPGRADE FROM FMR TAPE
> >
RE-INVENTORY (INV. STATUS) CHANGE LDR MODE AUTOMATIC
> >
>
LOOP MODE OFF
> >
> >
AUTOLOAD MODE OFF
> >
NET PARAMETER (INV. STATUS)
> >
BARCODE READER OFF
> >
PROTECTION MODE OFF
> >
SERIAL NUMBER 0123456789
>
75
Information Menu
See Information Menu on page 49.
Commands Menu
See Commands Menu on page 55.
Configuration Menu
The Configuration Menu allows the administrator to setup or change SCSI IDs, SCSI speed, operating mode, network parameters, as well as, initializing the BCR. For navigation information and descriptions of menu items, refer to the sections that follow. To navigate to the Configuration Menu from the Home Screen using the OCP: v Press any button (Cancel, Previous, Next, or Enter) on the OCP to display the Information Menu screen. v Press Next until the Configuration Menu screen displays.
RESET
RESET restarts the Autoloader and is used when initiating configuration changes.
Legend Cancel Enter > Previous > Next
X
To access RESET using the OCP: 1. 2. 3. 4. Navigate to the Configuration Menu (see Configuration Menu). Press Enter to access RESET. Press Enter to initiate the reset. When the reset is complete, the OCP will display the Home Screen.
CHANGE LOOP ID
CHANGE LOOP ID allows the user to set a new value for Fibre Loop IDs. The Fibre Loop default ID is 005.
Legend Cancel Enter > Previous > Next
X
| |
To access CHANGE LOOP ID using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu). 2. Press Enter then Next or Previous, as necessary, until CHANGE LOOP ID is displayed. 3. Press Enter to display the CHANGE LOOP ID Drive (XX) screen. 4. Press Enter to display the CHANGE LOOP ID New ID: screen.
76
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0222
a67s0174
RESET STATUS
5. Use Next and Previous to select each digit in the new ID. After selecting each number, press Enter to initiate the selected number and move to the next digit in the ID. 6. After all digits have been selected and initiated, press Enter. 7. Cycle power on the Autoloader. After the power has cycled, the Home Screen will be displayed.
FIBRE CHANNEL
Legend Cancel Enter > Previous > Next
X
| |
To access FIBRE CHANNEL using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 76). 2. Press Enter then Next or Previous, as necessary, until FIBRE CHANNEL is displayed. 3. Press Enter to display the FIBRE CHANNEL TO: screen. 4. Use Next and Previous to select the new port (NL PORT, LN PORT, L PORT, or N PORT). Note: See Fibre Channel Supported Topologies on page 13 for detailed port information. 5. Press Enter to initiate the change and return to the FIBRE CHANNEL screen. 6. Press Next to go to the next menu item. Press Cancel: v One time to return to the Configuration Menu. v Two times to return to the Home Screen.
| |
WW NODE NAME
Legend Cancel Enter > Previous > Next
X
| |
To access WW NODE NAME using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 76). 2. Press Enter then Next or Previous, as necessary, until WW NODE NAME is displayed. 3. Press Enter to display the CHANGE NODE NAME TO: OVERWRITE NN screen. 4. Press Enter to access the current Node Name. 5. Use Next and Previous to select each digit in the new name. Press Enter after each digit is selected to initialize the digit and move to the next digit to be changed.
Operator Guide: Menus
a67s0224
a67s0223
77
6. Cycle power on the Autoloader. After the power has cycled, the Home Screen will display. 7. Verify that the WWNN was changed. If not, cycle power again.
FIBRE SPEED
Attention: FC SPEED is supported by certain host bus adapters. To determine if your adapter supports FC SPEED: v Refer to the documentation for your server (host). v Visit the web at http://www.ibm.com/storage/support/lto.
access FC SPEED using the OCP: Navigate to the Configuration Menu (see Configuration Menu on page 76). Press Enter then Next or Previous, as necessary, until FC SPEED is displayed. Press Enter to display the CHANGE SPEED TO: screen. Use Next and Previous to select the new speed: v 1 Gb/s v 2 Gb/s v AUTO (variable speed; maximum speed allowed at the time) 5. Press Enter to initiate the change and return to the HI SPEED FC screen. 6. Cycle Autoloader power. When power has cycled, the Home Screen displays.
To 1. 2. 3. 4.
78
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| |
To access CHANGE LDR MODE: 1. Navigate to the Configuration Menu (see Configuration Menu on page 76). 2. Press Enter then Next or Previous, as necessary, until CHANGE LDR MODE is displayed. 3. Press Enter on the OCP to display the CHANGE LDR MODE TO: screen. 4. Use Next and Previous on the OCP to select the new mode (Automatic, Sequential, or Random). 5. Press Enter on the OCP to initiate the new mode. 6. Press Cancel on the OCP: v One time to return to the Configuration Menu screen. v Two times to return to the Home Screen. Automatic Mode: Automatic mode is the default setting and allows the Autoloader to switch between sequential and random modes depending on the SCSI command received. In automatic mode, sequential mode is activated when the Autoloader is powered on. When the Autoloader receives a MOVE MEDIUM, READ ELEMENT STATUS, or an INITIALIZE ELEMENT STATUS command, sequential mode is disabled and random mode becomes active. The Autoloader will switch back to sequential mode with every OCP initiated LOAD or UNLOAD command. Sequential Mode: In sequential mode, the Autoloaders firmware predefines the selection of the cartridges. After initialization, the firmware causes the Autoloader to select the first available cartridge found (counting from 1 through 8) for loading into the drive. If AUTOLOAD MODE (see Automatic Mode) is set to ON, the first cartridge will load automatically. Otherwise, the OCPs LOAD CARTRIDGE command must be executed. After the servers (hosts) application software fills this cartridge with data and issues an UNLOAD command, the Autoloader returns the cartridge to its storage slot and loads the next cartridge in order. Empty storage slots are ignored. The Autoloader continues this process until all cartridges have been filled with data. Note: While in sequential mode, the Autoloaders robotics are not logically connected to the SCSI bus and do not respond to SCSI commands. Associated with sequential mode are LOOP MODE and AUTOLOAD MODE. See LOOP MODE and AUTOLOAD MODE on page 80 for more information. Random Mode: In random mode, the Autoloader allows the servers (hosts) application software to select any data cartridge in any order.
LOOP MODE
LOOP MODE can be used with sequential mode. Sequential mode with LOOP MODE ON loads the cartridge in slot 1 after the cartridge in slot 8 has been filled and sent back to its home slot to allow endless backup operations without user interaction.
a67s0190
79
To access LOOP MODE: 1. Navigate to the Configuration Menu (see Configuration Menu on page 76). 2. Press Enter then Next or Previous, as necessary, until LOOP MODE is displayed. 3. Press Enter on the OCP to display the LOOP MODE CHANGE TO: screen. 4. Use Next and Previous on the OCP to select ON or OFF. 5. Press Enter on the OCP to initiate the new mode. 6. Press Cancel on the OCP: v One time to return to the Configuration Menu screen. v Two times to return to the Home Screen.
AUTOLOAD MODE
AUTOLOAD MODE can be used with sequential mode. Sequential Mode with AUTOLOAD MODE ON loads the first cartridge automatically if the Autoloader powers on with an empty drive.
Legend Cancel Enter > Previous > Next
X
| |
To access AUTOLOAD MODE: 1. Navigate to the Configuration Menu (see Configuration Menu on page 76). 2. Press Enter then Next or Previous, as necessary, until AUTOLOAD MODE is displayed. 3. Press Enter on the OCP to display the AUTOLOAD MODE CHANGE TO: screen. 4. Use Next and Previous on the OCP to select ON or OFF. 5. Press Enter on the OCP to initiate the new mode. 6. Press Cancel on the OCP: v One time to return to the Configuration Menu screen. v Two times to return to the Home Screen.
NET PARAMETER
Turn NET PARAMETER ON when an RMU is installed on the Autoloader. This menu item also allows the user to: v Turn DHCP (Dynamic Host Configuration Protocol) on or off v Set or change the Autoloaders IP Address v Set or change the Autoloaders Gateway Address v Set or change the Autoloaders Network Mask Address
80
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0192
a67s0191
NETWORK OFF
> >
X
DHCP OFF
> >
X
IP ADDRESS XXX.YYY.ZZZ.VVV
> >
GATEWAY ADDRESS XXX.YYY.ZZZ.VVV
> >
NETMASK XXX.YYY.ZZZ.VVV
NETMASK XXX.YYY.ZZZ.VVV
| |
To access NET PARAMETER using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 76). 2. Press Enter then Next or Previous, as necessary, until NET PARAMETER is displayed. a. Press Enter to display the NETWORK screen. Current status is displayed. b. Press Enter to display the NETWORK CHANGE TO: screen c. Use Next and Previous to select ON or OFF. d. Press Enter to initiate the change and return to the NETWORK screen. 3. Press Next to display the DHCP screen. Current status is displayed. a. Press Enter to display the DHCP CHANGE TO: screen. b. Use Next and Previous to select ON or OFF. c. Press Enter to initiate the change and return to the DHCP screen. 4. Press Next to display the IP ADDRESS screen. The current IP Address is displayed. a. Press Enter to display the CHANGE IP ADDRESS screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Cancel to return to the IP ADDRESS screen. 5. Press Next to display the GATEWAY ADDRESS screen. The current Gateway Address is displayed. a. Press Enter to display the CHANGE GATEWAY screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Cancel to return to the GATEWAY ADDRESS screen.
a67s0176
81
6. Press Next to display the NETMASK screen. The current Netmask address is displayed. a. Press Enter to display the CHANGE NETMASK screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Cancel to return to the NETMASK screen. 7. Press Cancel: v One time to return to the NET PARAMETER screen. v Two times to return to the Configuration Menu screen. v Three times to return to the Home Screen.
BARCODE READER
Turn BARCODE READER ON when a BCR is installed on the Autoloader.
| |
To access BARCODE READER using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 76). 2. Press Enter then Next or Previous, as necessary, until BARCODE READER is displayed. a. Press Enter to display the BARCODE READER CHANGE TO: screen b. Use Next and Previous to select ON or OFF. c. Press Enter to initiate the change and return to the Home Screen.
PROTECTION MODE
| | | Turn PROTECTION MODE ON to initiate a password protected login. Leave PROTECTION MODE OFF (default setting) to allow going offline without a password.
X
PROTECTION ON
PROTECTION MODE ON
a67s0244
82
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0231
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
Turning PROTECTION MODE ON: To activate password protection on the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, to access PROTECTION MODE. Press Enter to display the PROTECTION MODE CHANGE TO: screen. Use Next or Previous to select ON. Press Enter to initiate the change. Enter a new PIN (password) using Next and Previous. After selecting each digit, press Enter to initiate the entry and move to the next digit. e. Press Enter to confirm the new PIN (password). PROTECTION ON is displayed. f. Press Enter to return to the PROTECTION MODE screen. 3. Press Cancel: v One time to return to the Configuration Menu. v Two times to return to the Home screen. a. b. c. d. Turning PROTECTION MODE OFF: To deactivate password protection on the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, to access PROTECTION MODE. a. Press Enter to display the PROTECTION MODE CHANGE TO: screen. b. Use Next or Previous to select OFF. c. Press Enter to initiate the change. The message Disable protect are you sure? is displayed. d. Press Enter for YES or Cancel for NO. e. Press Enter to return to the PROTECTION MODE CHANGE TO: screen. 3. Press Cancel: v One time to return to the PROTECTION MODE screen. v Two times to return to the Configuration Menu screen. v Three times to return to the Home screen.
SERIAL NUMBER
This menu item allows the user to change the serial number displayed by the OCP. This item should be utilized when a replacement Autoloader is being installed. The serial number of the replacement Autoloader should be changed to the serial number of the original Autoloader for warranty purposes.
Legend Cancel Enter
| |
To access SERIAL NUMBER via the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, until SERIAL NUMBER is displayed. 3. Press Enter to display the CHANGE SER NUM screen.
Operator Guide: Menus
a67s0248
83
4. Use Next and Previous to select each alphanumeric digit in the new serial number. Press Enter to initiate each new digit and move to the next digit to be changed. The Autoloaders serial number is seven digits in length; therefore, the first three digits of the serial number should be entered as 000. 5. Press Cancel to return to the SERIAL NUMBER screen.
Diagnostic Menu
See Diagnostic Menu on page 67.
Go Online
See Go Online on page 74.
84
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Configuration
| | | | | | | | Configuring the Autoloader consists of the following steps: 1. Setting passwords (see Passwords) 2. Setting model-specific configuration options v See Configuring a Model L28/L38/L3H Autoloader on page 91 - OR v Configuring a Model F28/F38/F3H Autoloader on page 99 3. Setting configuration options common to all models (seeCompleting Configuration of Autoloader on page 107)
Passwords
Password-protected logins are available with the OCP, the RMU, and serial communication. Password protected logins are: v Optional with the OCP. v Mandatory with all RMU user levels. v Mandatory with serial communication Administrator and Service user levels; not mandatory for the Standard user level.
OCP Password
Password protection can be turned on or off for the OCP.
| | |
85
| | |
6. If GO OFFLINE PASSED is displayed, press Enter to complete going offline. If GO OFFLINE FAILED displays, the PIN (password) was incorrect. Press Cancel and repeat this procedure. 7. Press Enter to complete the login.
RMU Passwords
Password protection is a standard feature of the RMU. The Administrator must log in using the factory password setting the first time the RMU is used. This password can be changed after the initial login, if desired.
Using HyperTerminal
1. Start the terminal emulation software (such as, HyperTerminal). On your Windows desktop, click Select>Programs>Accessories >Communications >HyperTerminal. Note: Other applications similar to HyperTerminal exist. If you are using an application other than HyperTerminal, please refer to that applications documentation for instructions. 2. On the Connection Description window: v Type in 3581. v Click OK.
86
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0237
Configuration
87
3. On the Connect To window: v Select the COM port that the serial cable was plugged into on the rear of your server (host). v Click OK.
88
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0238
4. On the Comx Properties window: v Select the following port settings: Bits per second = 38 400 Data bits = 8 Parity = None Stop Bit = 1 Flow control = None v Click OK.
a67s0239
Configuration
89
5. Press Enter. If you see the following screen, all went well and you are able to use the Serial Monitor. If you see nothing like this or only scrambled characters, check your connection parameters.
TSMON>
7. Press Enter. 8. To access the administrator serial menu: a. Type lgi and press Enter.
TSMON>lgi
Note: Both the OCP and RMU must be online (logged out) before the serial port will allow login. 1) For the User ID, type admin (Administrator) or the new Adminstrator User ID set for the RMU.
TSMON>lgi User ID:admin
2) For the password, type secure (Administrator) or the new Administrator password set for the RMU.
TSMON>lgi User ID:admin Password:secure
3) Press Enter to display the full serial menu. 9. After completing all serial communication, logout by completing the following: a. At the TSMON> prompt, type lgo.
TSMON>lgo
b. Press Enter.
90
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | |
| | | | | | |
To 1. 2. 3. 4. 5.
access CHANGE SCSI ID using the OCP: Navigate to the Configuration Menu (see Configuration Menu on page 60). Press Enter then Next until CHANGE SCSI ID is displayed. Press Enter to display the CHANGE SCSI ID Drive [XX] screen. Press Enter to display the CHANGE SCSI ID New SCSI ID: screen. Use Next and Previous to select each digit in the new ID. After selecting each number, press Enter on the OCP to initiate the selected number and move to the next digit in the ID. 6. At the CYCLE POWER FOR NEW SCSI ID screen, press Cancel two times to return to the CHANGE SCSI ID screen.
Configuration
91
a67s0189
To access SCSI SPEED using the OCP: 1. Press Next or Previous, as necessary, to display SCSI SPEED. 2. Press Enter to display the CHANGE SPEED TO: screen. 3. Use Next and Previous to select the new SCSI speed: v 80 Mb/s v AUTO (variable maximum speed) 4. Press Enter to initiate the new speed. 5. At the CYCLE POWER FOR NEW xxx screen, press Cancel one time to return to the SCSI SPEED screen.
92
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0190
a67s0193
To 1. 2. 3.
access CHANGE LDR MODE using the OCP: Press Next or Previous, as necessary, until CHANGE LDR MODE is displayed. Press Enter to display the CHANGE LDR MODE TO: screen. Use Next and Previous to select the new mode (Automatic, Sequential, or Random). 4. Press Enter to initiate the new mode. Automatic Mode: Automatic mode is the default setting and allows the Autoloader to switch between sequential and random modes depending on the SCSI command received. In automatic mode, sequential mode is activated when the Autoloader is powered on. When the Autoloader receives a MOVE MEDIUM, READ ELEMENT STATUS, or an INITIALIZE ELEMENT STATUS command, sequential mode is disabled and random mode becomes active. The Autoloader will switch back to sequential mode with every OCP initiated LOAD or UNLOAD command. Sequential Mode: In sequential mode, the Autoloaders firmware predefines the selection of the cartridges. After initialization, the firmware causes the Autoloader to select the first available cartridge found (counting from 1 through 8) for loading into the drive. If AUTOLOAD MODE (see AUTOLOAD MODE on page 63) is set to ON, the first cartridge will load automatically. Otherwise, the OCPs LOAD CARTRIDGE command must be executed. After the servers (hosts) application software fills this cartridge with data and issues an UNLOAD command, the Autoloader returns the cartridge to its storage slot and loads the next cartridge in order. Empty storage slots are ignored. The Autoloader continues this process until all cartridges have been filled with data. Note: While in sequential mode, the Autoloaders robotics are not logically connected to the SCSI bus and do not respond to SCSI commands. Associated with sequential mode are LOOP MODE and AUTOLOAD MODE. See LOOP MODE and AUTOLOAD MODE on page 94 for more information. Random Mode: In random mode, the Autoloader allows the servers (hosts) application software to select any data cartridge in any order.
LOOP MODE
LOOP MODE can be used with sequential mode. Sequential mode with LOOP MODE ON loads the cartridge in slot 1 after the cartridge in slot 8 has been filled and sent back to its home slot. This allows endless backup operations without user interaction.
Legend Cancel Enter > Previous > Next
X
To 1. 2. 3. 4.
access LOOP MODE using the OCP: Press Next or Previous, as necessary, until LOOP MODE is displayed. Press Enter to display the LOOP MODE CHANGE TO: screen. Use Next and Previous to select ON or OFF. Press Enter to initiate the new mode.
Configuration
a67s0191
93
AUTOLOAD MODE
AUTOLOAD MODE can also be used with sequential mode. Sequential mode with AUTOLOAD MODE ON loads the first cartridge automatically if the Autoloader powers on with an empty drive.
Legend Cancel Enter > Previous > Next
X
To 1. 2. 3. 4. 5.
access AUTOLOAD MODE on the OCP: Press Next or Previous, as necessary, to display AUTOLOAD MODE. Press Enter to display the AUTOLOAD MODE CHANGE TO: screen. Use Next and Previous to select ON or OFF. Press Enter to initiate the new mode. Press Cancel two times to return to the Home Screen.
94
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0192
NETWORK OFF
> >
X
DHCP OFF
> >
X
IP ADDRESS XXX.YYY.ZZZ.VVV
> >
GATEWAY ADDRESS XXX.YYY.ZZZ.VVV
> >
NETMASK XXX.YYY.ZZZ.VVV
NETMASK XXX.YYY.ZZZ.VVV
| | |
To access NET PARAMETER using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, until NET PARAMETER is displayed. a. Press Enter to display the NETWORK screen. Current status is displayed. b. Press Enter to display the NETWORK CHANGE TO: screen c. Use Next and Previous to select ON or OFF. d. Press Enter to initiate the change and return to the NETWORK screen. 3. Press Next to display the DHCP screen. Current status is displayed. a. Press Enter to display the DHCP CHANGE TO: screen. b. Use Next and Previous to select ON or OFF. c. Press Enter to initiate the change and return to the DHCP screen. 4. Press Next to display the IP ADDRESS screen. The current IP Address is displayed. a. Press Enter to display the CHANGE IP ADDRESS screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the IP ADDRESS screen. 5. Press Next to display the GATEWAY ADDRESS screen. The current Gateway Address is displayed.
Configuration
a67s0176
95
| |
a. Press Enter to display the CHANGE GATEWAY screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the GATEWAY ADDRESS screen. 6. Press Next to display the NETMASK screen. The current Netmask address is displayed. a. Press Enter to display the CHANGE NETMASK screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the NETMASK screen. 7. Press Cancel: v One time, and the message CYCLE POWER FOR NEW NETPARAM is displayed. v Two times to return to the NET PARAMETER screen. v Three times to return to the Configuration Menu screen. v Four times to return to the Home Screen.
| |
| | |
To access BARCODE READER using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then Next or Previous, as necessary, until BARCODE READER is displayed. a. Press Enter to display the BARCODE READER CHANGE TO: screen b. Use Next and Previous to select ON or OFF. c. Press Enter to initiate the change. If ON was selected, the barcode reader will inventory all cartridges in the autoloader. 3. Press Cancel: v One time to return to the Barcode Reader screen. v Two times to return to the Configuration Menu . v Three times to return to the Home screen.
| | |
96
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0231
| |
PROTECTION ON
PROTECTION MODE ON
a67s0244
| | | |
Turn Protection Mode ON to initiate a password-protected login. Leave Protection Mode OFF (default setting) to allow going offline without a password. See PROTECTION MODE on page 82 for instructions on how to set Protection Mode ON or OFF.
The selected VPD items are now saved in the save area on the RMU unit installed on the rear panel of the Autoloader. Notes: 1. Any time one of the selected VPD items are changed, the above procedure should be used to ensure that the saved data is always the latest. 2. The Autoloader Configuration Form on page 251 should also be updated anytime one of the VPD items is changed.
| |
Configuration
97
| | | | | | | | | | | | | | | | | | | | | |
98
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
To 1. 2. 3. 4. 5.
access CHANGE LOOP ID using the OCP: Navigate to the Configuration Menu (see Configuration Menu on page 76). Press Enter then Next to access CHANGE LOOP ID. Press Enter to display the CHANGE LOOP ID Drive (XXX) screen. Press Enter to display the CHANGE LOOP ID New ID: screen. Use Next and Previous to select each digit in the new ID. After selecting each number, press Enter to initiate the selected number and move to the next digit in the ID.
Configuration
99
a67s0222
6. After all digits have been selected and initiated, press Cancel two times to return to CHANGE LOOP ID.
To access FIBRE CHANNEL using the OCP: 1. Press Next or Previous, as necessary, to access FIBRE CHANNEL. 2. Press Enter to display the FIBRE CHANNEL TO: screen. 3. Use Next and Previous to select the new port (LN PORT [default], NL PORT, L PORT, N PORT). For more information on the port selections, see Fibre Channel Supported Topologies on page 13. 4. Press Enter to initiate the change and return to the FIBRE CHANNEL screen.
To 1. 2. 3. 4.
access WW NODE NAME using the OCP: Press Next or Previous, as necessary, to access WW NODE NAME. Press Enter to display the CHANGE NODE NAME TO: screen. Press Enter to display the current Node Name. Use Next and Previous to select each digit in the new name. Press Enter after each digit is selected to initialize the digit and move to the next digit to be changed. 5. When prompted to cycle power, press Cancel to return to the WW NODE NAME screen.
100
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0224
a67s0223
To access FC SPEED using the OCP: 1. Press Next or Previous, as necessary, to access FC SPEED. 2. Press Enter to display the CHANGE SPEED TO: screen. 3. Use Next and Previous to select the new speed: v 1 Gb/s v 2 Gb/s v AUTO (variable speed; maximum speed allowed at the time) 4. Press Enter to initiate the change. 5. When prompted to cycle power, press Cancel to return to the FC Speed screen.
To 1. 2. 3.
access CHANGE LDR MODE: Press Next or Previous, as necessary, until CHANGE LDR MODE is diisplayed. Press Enter to display the CHANGE LDR MODE TO: screen. Use Next and Previous to select the new mode (Automatic, Sequential, or Random). 4. Press Enter to initiate the new mode. Automatic Mode: Automatic mode is the default setting and allows the Autoloader to switch between sequential and random modes depending on the SCSI command received. In automatic mode, sequential mode is activated when the Autoloader is powered on. When the Autoloader receives a MOVE MEDIUM, READ ELEMENT STATUS, or an INITIALIZE ELEMENT STATUS command, sequential mode is disabled and random mode becomes active. The Autoloader will switch back to sequential mode with every OCP initiated LOAD or UNLOAD command.
a67s0190
Configuration
101
Sequential Mode: In sequential mode, the Autoloaders firmware predefines the selection of the cartridges. After initialization, the firmware causes the Autoloader to select the first available cartridge found (counting from 1 through 8) for loading into the drive. If AUTOLOAD MODE (see Automatic Mode on page 79) is set to ON, the first cartridge will load automatically. Otherwise, the OCPs LOAD CARTRIDGE command must be executed. After the servers (hosts) application software fills this cartridge with data and issues an UNLOAD command, the Autoloader returns the cartridge to its storage slot and loads the next cartridge in order. Empty storage slots are ignored. The Autoloader continues this process until all cartridges have been filled with data. Note: While in sequential mode, the Autoloaders robotics are not logically connected to the SCSI bus and do not respond to SCSI commands. Associated with sequential mode are LOOP MODE and AUTOLOAD MODE. See LOOP MODE and AUTOLOAD MODE for more information. Random Mode: In random mode, the Autoloader allows the servers (hosts) application software to select any data cartridge in any order.
LOOP MODE
LOOP MODE can be used with sequential mode. Sequential mode with LOOP MODE ON loads the cartridge in slot 1 after the cartridge in slot 8 has been filled and sent back to its home slot. This allows endless backup operations without user interaction.
Legend Cancel Enter > Previous > Next
X
To 1. 2. 3. 4.
access LOOP MODE: Press Next or Previous, as necessary, to access LOOP MODE. Press Enter to display the LOOP MODE CHANGE TO: screen. Use Next and Previous to select ON or OFF. Press Enter to initiate the new mode.
AUTOLOAD MODE
AUTOLOAD MODE can be used with sequential mode. Sequential Mode with AUTOLOAD MODE ON loads the first cartridge automatically if the Autoloader powers on with an empty drive.
Legend Cancel Enter > Previous > Next
X
102
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0192
a67s0191
To 1. 2. 3. 4.
access AUTOLOAD MODE: Press Next or Previous, as necessary, to access AUTOLOAD MODE. Press Enter to display the AUTOLOAD MODE CHANGE TO: screen. Use Next and Previous to select ON or OFF. Press Enter to initiate the new mode.
NETWORK OFF
> >
X
DHCP OFF
> >
X
IP ADDRESS XXX.YYY.ZZZ.VVV
> >
GATEWAY ADDRESS XXX.YYY.ZZZ.VVV
> >
NETMASK XXX.YYY.ZZZ.VVV
NETMASK XXX.YYY.ZZZ.VVV
To access NET PARAMETER using the OCP: 1. Navigate to the Configuration Menu (see Configuration Menu on page 76). | | 2. Press Enter then Next or Previous, as necessary, until NET PARAMETER is displayed. a. Press Enter to display the NETWORK screen. Current status is displayed. b. Press Enter to display the NETWORK CHANGE TO: screen c. Use Next and Previous to select ON or OFF. d. Press Enter to initiate the change and return to the NETWORK screen. 3. Press Next to display the DHCP screen. Current status is displayed. a. Press Enter to display the DHCP CHANGE TO: screen. b. Use Next and Previous to select ON or OFF. c. Press Enter to initiate the change and return to the DHCP screen. 4. Press Next to display the IP ADDRESS screen. The current IP Address is displayed. a. Press Enter to display the CHANGE IP ADDRESS screen.
Configuration
a67s0176
103
b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the IP ADDRESS screen. 5. Press Next to display the GATEWAY ADDRESS screen. The current Gateway Address is displayed. a. Press Enter to display the CHANGE GATEWAY screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the GATEWAY ADDRESS screen. 6. Press Next to display the NETMASK screen. The current Netmask address is displayed. a. Press Enter to display the CHANGE NETMASK screen. b. Use Next and Previous to select each digit in the new address. Press Enter to initiate each new digit and move to the next digit to be changed. c. After all digits have been changed and initiated, press Enter to return to the NETMASK screen. 7. Press Cancel to return to the NET PARAMETER screen.
| |
| |
To access BARCODE READER using the OCP: 1. Press Next to access BARCODE READER. a. Press Enter to display the BARCODE READER CHANGE TO: screen b. Use Next and Previous to select ON or OFF. c. Press Enter to initiate the change. If ON was selected, the Barcode Reader will inventory all the cartridges in the autoloader. 2. Press Cancel: v One time to return to the BARCODE READER screen. v Two times to return to the Configuration Menu. v Three times to return to the Home screen.
104
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0231
PROTECTION ON
PROTECTION MODE ON
a67s0244
| | | | | | |
Turn Protection Mode ON to initiate a password-protected login. Leave Protection Mode OFF (default setting) to allow going offline without a password. See PROTECTION MODE on page 82 for instructions on how to set Protection Mode ON or OFF.
Step 11. Save Vital Product Data (Autoloader with RMU Only)
Selected Vital Product Data (VPD) items are saved on the RMU installed on the rear panel of the Autoloader for possible use in the case where the Autoloader base unit needs to be replaced. Saving VPD in this manner facilitates quick VPD transfer from the original machine to the replacement machine and eliminates having to use the OCP to re-configure the replacement machine. Model F28/F38/F3H VPD Items Saved on the RMU: v Loop ID v Fibre Channel (Loop) Port Type v WW Node Name v Fibre Channel Drive Speed v Operating Mode v BCR Enablement v Machine Serial Number To 1. 2. 3. save VPD to the RMU: Login to the RMU at the Administrator level. Select Reset in the Configuration Menu. Press the Save Vital Product Data button.
| |
The selected VPD items are now saved in the save area on the RMU unit installed on the rear panel of the Autoloader. Notes: 1. Any time one of the selected VPD items are changed, the above procedure should be used to ensure that the saved data is always the latest.
Configuration
105
| | | | | | | | | | | | | | | | | | | | | | | | | |
2. The Autoloader Configuration Form on page 251 should also be updated any time one of the VPD items is changed.
106
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
BULK EXCHANGE
BULK EXCHANGE enables the user to import or export all cartridges. Operation begins with Slot 1. If a cartridge is available, it will be exported. It is up to the user to import a new cartridge or to move to Slot 2. The same procedure repeats for the remainder of the eight slots.
Legend Cancel Enter > Previous > Next
X
To 1. 2. 3. 4.
access BULK EXCHANGE using the OCP: Navigate to the Commands Menu (see Commands Menu on page 55). Press Enter to access BULK EXCHANGE. Press Enter to initiate the importing and/or exporting of cartridges. When the I/O Door opens, remove the ejected cartridge or proceed to the next step.
5. Do one of the following: v Insert another cartridge gently pushing the cartridge through the I/O Door until the cartridge can be pushed no farther. v Press Enter to export the next cartridge. - OR v Press Cancel to terminate BULK EXCHANGE. 6. When all cartridges have been imported and/or exported, the Autoloader will return to the Home Screen.
a67s0219
Configuration
107
IMPORT
The IMPORT command allows the user to insert and choose a destination slot for a cartridge in the Autoloader.
DOOR STATUS
To access IMPORT using the OCP: 1. Navigate to the Commands Menu (see Commands Menu on page 55). 2. Press Enter then Next or Previous, as necessary, to access IMPORT. 3. Press Enter to display the IMPORT TO: screen. 4. Use the Next and Previous to select the number of the slot to which the cartridge is to be imported. (Only those slots that are empty will be available for selection.) 5. Press Enter to initiate the procedure. 6. When the I/O Door opens, insert a cartridge. The Autoloader will import the cartridge, close the I/O Door, and insert the cartridge into the selected slot. 7. Repeat Steps 4 through 6 until all cartridges have been imported. 8. When the last cartridge has been inserted into its slot, press Cancel to return to the IMPORT screen. 9. Press Cancel to prompt the BCR (if installed) to re-inventory all cartridges and return to the Home Screen.
108
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0171
1. Access Level: Select the access level to be changed: 1 - Standard 2 - Administrator 3 - Service 2. Access Level Name: Enter the name to be associated with the access level. 3. Password: Enter the password (a maximum of 15 characters) to be associated with the access level. 4. Repeat Password: Repeat the password entered in the previous item. 5. OCP Access Pin Enabled: Check this box to enable password-protected OCP login. 6. OCP Access Pin Code: Enter a 4 digit pin code for OCP access (not available with all models). If a password has already been keyed into the OCP, it will show up here. 7. Repeat OCP Access Pin Code: Repeat the pin code entered in the previous item (not available with all models). 8. Support Name: Enter the name of the person to provide support for the access level. This information will appear on the Support page. 9. Support Phone: Enter the phone number of the support person for the access level. This information will appear on the Support page. 10. Support Email: Enter the email address of the support person for the access level. This information will appear on the Support page. After all entries have been made, click SUBMIT to initiate the configuration changes. Repeat the steps to set up or change other access levels.
Configuration
109
For more information about device drivers, refer to any of the preceding device driver operating system directories.
110
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
1 min. 1 min.
Note: Updating firmware via FMR tape is for development and manufacturing use only. FMR tapes will not be shipped to the field to update drive firmware.
My Support
Note: My Support registration provides email notification when new firmware levels have been updated and are available for download and installation. To register for My Support, see Step 6. Register for My Support on page 121.
111
| |
To upgrade Autoloader and drive firmware via serial port, follow these instructions: Installing the Serial Cable: To install the serial cable, follow these instructions: 1. Power off the Autoloader. 2. Connect the serial cable to the Autoloader serial port (at rear connector plate). 3. Power on the Autoloader. Using HyperTerminal: 1. Start the terminal emulation software (such as, HyperTerminal). On your Windows desktop, click Select>Programs>Accessories >Communications >HyperTerminal. Note: Other applications similar to HyperTerminal exist. If you are using an application other than HyperTerminal, please refer to that applications documentation for instructions.
112
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0237
Configuration
113
3. On the Connect To window: v Select the COM port that the serial cable was plugged into on the rear of your server (host). v Click OK.
114
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0238
4. On the Comx Properties window: v Select the following port settings: Bits per second = 38 400 Data bits = 8 Parity = None Stop Bit = 1 Flow control = None v Click OK.
a67s0239
Configuration
115
5. Press Enter. If you see the following screen, all went well and you are able to use the Serial Monitor. If you see nothing like this or only scrambled characters, check your connection parameters.
TSMON>
7. To access the administrator serial menu: a. Type lgi and press Enter.
TSMON>lgi
Note: Both the OCP and RMU must be online (logged out) before the serial port will allow login. 1) For the User ID, type admin (Administrator) or the new Adminstrator User ID set for the RMU.
TSMON>lgi User ID:admin
2) For the password, type secure (Administrator) or the new Administrator password set for the RMU.
TSMON>lgi User ID:admin Password:secure
3) Press Enter. 8. To identify which firmware (Autoloader or drive) you wish to upgrade, enter one of the following after the TSMON> prompt: v lfw to upgrade library firmware. v dfw to upgrade drive firmware.
TSMON>lfw
Note: If the Autoloader has timed out, press Enter for a fresh screen and start this procedure over. 10. In the 3581-HyperTerminal windows toolbar, select Transfer then Send File....
116
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
v Browse to downloaded Autoloader or drive firmware file on server (host). Autoloader firmware has a .fbi file extension. Drive firmware has a .ro file extension. v Select XMODEM. v Click Send. If successful: The Xmodem file send for 3581 screen will show activity. The OCP will display FW UPGRADE. The OCPs green Activity LED will be flashing. 12. At the end of the firmware upgrade, the Autoloader will reboot. 13. When the following screen displays, verify the firmware revision uploaded is the correct version.
a67s0240
Configuration
117
a67s0247
Via RMU
Attention Download the latest levels of Autoloader and drive firmware by visiting: v http://www.ibm.com/storage/support/lto v ftp://index.storsys.ibm.com/358x For information on RMU installation and configuration, see Step 4. Install the Optional Remote Management Unit (RMU) on page 22. For information on using the RMU, see Remote Management Unit (RMU) on page 123.
| | |
| | |
| | | | | | | |
Attention A user can communicate with the Autoloader via the OCP, the RMU, or the serial port. The Autoloader will accept commands from only one communication method at a time. If communicating via the OCP, return to the Home Screen before attempting to communicate via another method (RMU or serial port). If communicating via the RMU, log out before attempting to communicate via another method (OCP or serial port). If communicating via the serial port, exit the connection before attempting to communicate via another method (OCP or RMU). To upgrade Autoloader and drive firmware via the RMU, follow these instructions: 1. Click on Support in the left frame of the RMU. 2. Click on the link to download the latest Autoloader and drive firmware onto your server (host). 3. Refer to Firmware (Models L28/L38/L3H and F28/F38/F3H) on page 139 for instructions.
| |
| | | |
Attention At the time of publication, the ITDT tool was not available. Register with MySupport (http://www.ibm.com/support/mySupport) to be notified by email when the tool becomes available, or periodically check the IBM support site (http://www.ibm.com/storage/lto). The ITDT tool offers multiple functional capabilities that simplify the task of updating tape and library firmware. It is available for most major platforms (Windows, AIX, Sun, Linux, Netware, and so on), and requires no special device drivers. This tool is similar to the LTO-TDX drive-only firmware update and dump retrieval tool described later in this chapter. Note: The ITDT tool is available on the IBM website http://www.ibm.com/storage/support/lto. In addition to the executable file (.exe), a README file will be posted on the web page. The README file
118
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
describes the features and capabilities of the ITDT tool, provides downloading instructions, and gives detailed information on how to use the tool. You use the ITDT tool to perform the following tasks: v Update firmware using SCSI to all IBM LTO Tape Drive and Tape Library products (non-IBM devices may not be selected). v Upload drive and library dump files v Perform drive and library diagnostics, including drive read/write diagnostics The ITDT tool is a command line utility. To invoke it, enter the executable itdt from the directory where the tool is located. The Help feature gives a brief explanation of each function and shows the required syntax. LTO-TDX: LTO SCSI and Fibre Drive Firmware Download & LTO Drive Dump Upload Tool: The tool, LTO-TDX, is an alternative method for downloading LTO drive firmware across the SCSI bus or fibre channel. In addition, this tool can be used to upload LTO drive error dumps. The following information describes how to obtain the tool and lists its capabilities. 1. The tool supports all IBM LTO Gen 1 and Gen 2 SCSI and FC drives. The tool will not support any other manufacturers LTO drive. The tool is available for three different operating systems: v LTO-TDX_WinTool (for Windows operating systems) v LTO-TDX_NWTool (for Netware operating systems) v LTO-TDX_LxTool (for Linux operating systems) 2. The tool can perform two functions: a. Download firmware to the drive b. Upload a dump of the drive firmware logs from the drive to a computer system 3. The tool is distributed from the IBM web site. Download the tool by visiting http://www.ibm.com/storage/support/lto/. The install package or an executable file will be placed on the host system in a location chosen by the user. 4. When the user opens the install package, a license agreement will be presented. This license agreement must be accepted to proceed with the install. The user will also be presented with a license anytime the executable file is copied to another location where the firmware or dump folders do not exist. The tool will detect the missing folders at launch and present the users license, assuming that this is the first launch of a new copy of the tool. There will also be a function that allows the user to view the license at will when starting the tool. 5. The Windows install package will create a directory for the tool on the users hard disk and place the executable file (the tool) in that directory. The install package will also load the file into the Programs Menu accessed via the Start button and put an icon on the desktop of the Windows operating system. The install package shall perform a similar function on any other operating system that has a similar structure. 6. Selection of the icon on the desktop or selection of the tool from the Program Menu will start the tool and create the LTO Firmware and LTO Dumps files in the directory with the executable tool file. 7. The user must first put the firmware to be downloaded in the firmware folder. 8. Any dumps created will be put in the dump folder.
Configuration
119
9. The tool will present a list of the supported devices on the bus. The tool will allow selection of a target device and then perform the download or the dump on the target device. 10. The tool itself is a command line tool but it is menu driven and very simple to use. 11. The program displays are in English. 12. The user is responsible to make sure the drive is not in use when firmware is downloaded or a dump is taken. The user also must remove any cartridge from the drive or the firmware download function will not work. 13. If the user does make a mistake, the program will respond with instructive error messages. 14. If no IBM LTO tape drives are on the bus, the tool must inform the user that there are none before closing the tool window. Firmware Download Function: 1. The tool is capable of displaying the current firmware level for any drive on the bus. 2. The tool does a check to see if a cartridge is in the drive (cartridge present sensor activated). If a cartridge is present, an error shall be posted and the user shall be asked to remove the cartridge. 3. The tool downloads code to IBM LTO drives ONLY. The tool shall recognize ULT3580-TDX inquiry string devices as well as ULTRIUM-TDX devices. The letter X could be 1, 2, 3, or 4. 4. The tool is capable of loading back level (older) code. 5. The program presents the user with a numbered list of firmware files available for selection from the LTO Firmware folder. The user can then select the number of the firmware file for the program to load. 6. After the firmware has been loaded into drive memory the drive automatically reboots. The tool discourages the user from power cycling the drive before the reboot is complete. A message is displayed saying Updating.....Please Wait until the reboot is complete. A progress gauge is displayed letting the user know something is still happening. 7. A Wait message is displayed on the user screen during firmware load. 8. If the program tries to load code and it fails with a sense Key 5 and an ASC/ASCQ of 82/83, the following wording is displayed: Bad Firmware Detected. The firmware is the wrong type for your tape drive or the file is corrupted. Download the file again from the IBM Web site and try the procedure again. Drive Log Dump Function: 1. When the dump function is executed on a drive, the tool shall read the existing dump on the drive, force a dump, then read the forced dump. This will create two dump files. 2. The two dump files created by the dump function will be time stamped with year, month, day, and seconds and contain the drive serial number. The first dump file read has an A suffix. The second file produced has a B suffix. 3. The Tool will place the files that are created in the LTO Dumps folder in the directory with the tool. 4. The tool creates the dump files with a file type of .dmp.
120
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
NTUTIL or TAPEUTIL for Updating Autoloader and Drive Firmware: Autoloader and drive firmware can be updated over your servers (hosts) SCSI bus by using the device drivers and utilities that are supplied by IBM. Before updating library or drive firmware, you must: 1. Download the latest version of Autoloader and drive firmware. To obtain the new firmware, download it from the web to the server by visiting: v http://www.ibm.com/storage/support/lto v ftp://index.storsys.ibm.com/358x 2. Install the latest version IBM device drivers. 3. Install the proper IBM utility (NTUTIL or TAPEUTIL) For instructions about installing and using the appropriate IBM device drivers and utilities (such as NTUTIL or TAPEUTIL), refer to the The IBM LTO Ultrium Tape Libraries Guide by visiting http://w3.itso.ibm.com/. To obtain instructions about using NTUTIL or TAPEUTIL, visit http://www.ibm.com/storage/support/lto/.
Configuration
121
122
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Access Protocol
All three Autoloader communication methods (OCP, RMU, and serial) can simultaneously be active on the lowest level (Information only). v RMU: Standard user v OCP: Online (logout) v Serial: lgo (logout) However, only one of the three methods can be active at any one time on the Administrator or Service levels (RMU and serial) or at the Offline level (OCP). The other two can remain active on the lowest level. If an attempt to login is made on either of the other two while the third has the highest level access, an Already Reserved message is displayed. The RMU will only allow access by a Standard user at the login panel. For best results: v If communicating via the OCP, return to the Home Screen (Go Online) before attempting to communicate via the RMU or serial port. v If communicating via the RMU, log out before attempting to communicate via the OCP or serial port. v If communicating via the serial port, log out before attempting to communicate via the OCP or RMU Attention: If at any time the RMU interface is not responding properly, click on your Browsers Back button or close out the browser session and try reconnecting using the RMU IP address. If still unsuccessful, cycle Autoloader power and login to the RMU again.
123
Login
Anyone trying to access the RMU is asked to log in. There are three access levels for logging in: v Standard User (Level 1) v Administrator (Level 2) v Service (Level 3) These names can be changed by clicking User under Configuration in the Work Items list. See User (Models L28/L38/L3H and F28/F38/F3H) on page 133 for more information. After a successful login the user will be able to view screens available to that users level of access. The Standard User can access the: v Information Menu v Status Menu An Administrator can access the: v Information Menu v Status Menu v Configuration Menu v Maintenance Menu (exception: Advanced Diagnostics) v Log Menu Service can access the: v Information Menu v Status Menu v Configuration Menu v Maintenance Menu v Log Menu To 1. 2. 3. login to the RMU: Select the User type. Enter your password. Click login. The Autoloader Information table in the Information menu will be displayed.
124
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Help
Clicking on the ? in the upper right corner above the Quick Status table displays helpful information on the active RMU window.
Quick Status
The Quick Status table is located on the right side of each RMU screen after login. It displays the current status of the Autoloader. The following entries appear in the table: v Name: Displays the name of the Autoloader. v Status: Indicates by icon (see Status Icons) the overall status of the Autoloader. v Lock: Displays a lock when the Administrator is in the process of making configuration changes. v Cartridge in drive: Displays the slot number of the tape currently mounted in the tape drive. v Drive Status: Indicates by icon the overall status of the tape drive. v Drive Activity: Indicates the current activity of the tape drive. v Robotic Action: Indicates the current activity of the Autoloaders robotics. v Time: Indicates the total amount of time the Autoloader has been in operation. v Drive Error Code: Displays the code of the last error that occurred. Clicking on this code will take the user to a description of the code.
Status Icons
Status icons that appear in the RMU interface are as follows: v The green icon means OK and indicates that the Autoloader is fully operational and no user intervention is required. v The yellow icon means Warning and indicates that user intervention is necessary but that the Autoloader is still capable of performing operations. v The red icon means Error and indicates that user intervention is required and that the Autoloader is not capable of performing operations.
125
Information Menu
The Information Menu displays information on the Autoloader and the tape drive. This menu is accessible by all user levels. No changes can be made to these menu items. To expand the menu, click on the +. |
This menu item displays the Autoloader Information table which includes the following entries: v Serial Number: Displays the Autoloaders serial number. v Machine Model: Displays the type of machine (3581) and mode (L28/L38/L3H or F28/F38/F3H). v Temperature: Displays the Autoloaders current temperature. v Controller Firmware Revision: Displays the revision level of the current firmware. v Firmware CRC: Displays the firmwares CRC. v Bootcode Firmware Revision: Displays the revision level of the current Bootcode Firmware. v Firmware Build Date: Displays the build date of the current firmware. v Number of Firmware Updates: Displays the number of times the firmware has been updated. v Number of Power Ups: Displays the number of times the Autoloader has been powered on. v Barcode Reader present: Displays Yes if the BCR has been enabled; No if it has not been enabled. v IP Address: Displays the Autoloaders IP Address. v Autoloader Mode: Displays the current operating mode.
126
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| |
This menu item displays the Drive Information table with the following entries: v Vendor ID: Displays the tape drives vendor. v Product ID: Displays the tape drives product ID. v Serial Number: Displays the tape drives serial number. v Product Revision: Displays the drives product revision number. v Firmware Revision: Displays the revision level of the current firmware. v SCSI ID: Displays the drives SCSI ID. v Temperature: Displays the drives temperature. v Cooling: Displays the RPMs of the drives cooling fan.
127
Status Menu
The Status Menu displays current status information on the Autoloader and its Media (tape cartridges). To expand the menu, click on the +. |
This menu item displays the Autoloader Status table which lists the following entries: v Status: Indicates by icon (see Status Icons on page 125) the current status of the Autoloader. v Cartridge in Operation: Displays the number of the cartridge currently in operation. v Number of Load-Unload Cycles: Displays the number of times the tape drive has loaded and unloaded a cartridge. v Operation Time: Displays the time accrued since the first start-up. v Current Drive Status: Displays the current status of the tape drive. v Current Drive Activity: Displays the current activity of the tape drive. v Number of Retries: Displays in a percentage format the number of retries. v Current Robotic Action: Displays the current action of the Autoloaders robotics. v Barcode Reader Enabled: Displays Yes if the BCR is enabled; No if the BCR is not enabled.
128
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
This menu item displays the Media Status table which lists the following: v Slot Nr: Identifies by number all eight cartridge slots. v Status: Indicates which slots contain cartridges and what kind of cartridge (Normal Tape, Cleaning Tape, Bad Tape, or Moving Tape). v In Drive: Indicates if a cartridge is currently in the tape drive. v Barcode: Displays the number on the cartridges bar code label (if a BCR is installed). v Write Protected: Indicates if a cartridge is write protected. The cartridge status icons are as follows: v Black cartridge = Normal v Blue cartridge = Cleaning v Red cartridge = Bad v Green cartridge = In Access (in drive)
129
Configuration Menu
The Configuration Menu allows an Administrator to enter or change configuration values for the Autoloader (Device), Network, User, RTC (Real Time Clock), Event Notification, and Reset. To expand the menu, click on the +. |
Figure 100. RMU Configuration Menus Device page for Model L28/L38/L3H
This menu item displays the Device Configuration table for a Model L28/L38/L3H (SCSI) Autoloader which contains the following: v Drive SCSI ID: To change the drive SCSI ID select a number from 0 to 15 from the drop-down menu. v Host speed: To change the host speed, select one of the following: 80 MB/s AUTO (variable maximum speed) v Autoloader Mode: To change the Autoloaders operation mode, select from the following: Random Sequential - Autoload - Loop Automatic Note: For information on operating modes, seeCHANGE LDR MODE on page 62. v Barcode Reader Enabled: Selected if BCR is enabled. After making your selections, click SUBMIT to initiate the changes.
130
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Figure 101. RMU Configuration Menus Device page for Model F28/F38/F3H
This menu item displays the Device Configuration table for a Model F28/F38/F3H (Fibre Channel) Autoloader which contains the following: v Factory Default WWNN: To restore the World Wide Node Name set at the factory, turn this option On by clicking the box. The default value is off. v World Wide Node Name: To change the WWNN, enter the new number here. v Loop ID: To change the Loop ID, select a number between 0 and 127 in the drop-down menu. Loop IDs between 0 and 125 are hard addresses. Loop IDs of 126 or 127 allow the Autoloader to dynamically arbitrate the AL_PA (soft addressing). v Port Type: To change the Port Type, select one of the following: LN Port (default setting) L Port N Port NL Port v Port Speed: To change the Port Speed, select one of the following: 1 Gb/s 2 Gb/s AUTO (variable maximum speed; default setting) v Autoloader Mode: To change the operating mode, select from the following: Random Sequential - Autoload - Loop Automatic (default setting) Note: For more information on operating modes, see CHANGE LDR MODE on page 78. v Barcode Reader Enabled: Selected if the BCR is enabled. After making your selections, click SUBMIT to initiate the changes.
| | |
| |
131
a67s0270
This menu item displays the Network Configuration table which contains the following: v DHCP Address: Select On if the Autoloader should get its IP Address from a DHCP server. v Hostname: Enter a hostname. v IP Address: Enter an IP Address. v Network Mask: Enter a Network Mask. v Gateway Address: Enter a Gateway Address. After all entries have been made, click SUBMIT to initiate the configuration changes. A pop-up box will appear asking, Are you sure? Click OK to initiate the changes or CANCEL to return to the Device Configuration table.
132
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
1. Access Level: Select the access level to be changed. 1 - Standard 2 - Administrator 2. 3. 4. 5. 6. 7. 3 - Service Access Level Name: Enter the name to be associated with the access level. Password: Enter the password (a maximum of 15 characters) to be associated with the access level. Repeat Password: Repeat the password entered in the previous item. OCP Access Pin Enabled: Check this box to enable password-protected OCP login. OCP Access Pin Code: Enter a 4 digit pin code for OCP access. If a password has already been keyed into the OCP, it will show up here. Repeat OCP Access Pin Code: Repeat the pin code entered in the previous item.
8. Support Name: Enter the name of the person to provide support for the access level. This information will appear on the Support page. 9. Support Phone: Enter the phone number of the support person for the access level. This information will appear on the Support page. 10. Support Email: Enter the email address of the support person for the access level. This information will appear on the Support page. After all entries have been made, click SUBMIT to initiate the configuration changes. Repeat the steps to set up or change other access levels.
133
This menu item (Real Time Clock) displays the Clock Configuration table which contains the following: v Time: Enter the current time and select between a 12 hour or 24 hour display. v Date: Enter the date (DD-MM-YYYY). After all entries have been made, click SUBMIT to initiate the configuration changes. |
This menu item displays the Log Configuration table which contains the following: v Error Log Mode: Select the desired event mode and select if recovered errors should be logged. v Trace Level: Select all desired event levels you want logged. v Trace Filter: Select all items you want to appear when entries are logged.
134
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Attention: These filters apply during logging of the entries in the database. THEY ARE NOT RETRIEVE FILTERS. When filtering out events, no events will be stored in the log database and, therefore, will not be retrievable. After all entries have been made, click SUBMIT to initiate the configuration changes. |
This menu item displays the Event Notification Configuration table which contains the following: v Notify Errors: Select whether the notification of errors should be emailed or not. v Notify Warnings: Select whether the notification of warnings should be emailed or not. v To Email Address: Enter the email address of the person to be notified in the event of an error of warning. v Email Domain: Enter the email domain to appear as the sender on the notification. v SMTP Server Address: Enter the IP Address of the SMTP server used to send the email. | | Note: The complete email address of the sender is built from the Loader Name and Email Domain, for example: TS000007@ibm.com. After all entries have been made, click SUBMIT to initiate the configuration changes.
135
a67s0250
This menu item displays the Configuration Reset table which contains the following: v Restore Factory defaults: Click RESTORE to restore all factory default setting. A pop-up box will appear asking, Are you sure? Click OK to restore all factory default settings or CANCEL to return to the Configuration Reset table. v Restore Vital Product Data: Click RESTORE to load saved vital product data (SCSI or Loop ID, etc.). A pop-up box will appear asking, Are you sure? Click OK to restore vital product data or CANCEL to return to the Configuration Reset table. v Save Vital Product Data: Click SAVE to save the current Autoloader configuration. The skip network settings box is selected and notifies the Autoloader to skip the network settings (IP, Gateway, and Netmask addresses) when resetting or downloading the configuration. To change and save new network settings (if an RMU is installed), deselect this box, change the settings, and save the configuration to the server (host). A pop-up box will appear asking, Are you sure? Click OK to save the changes or CANCEL to return to the Configuration Reset table. After restoring or saving settings, do one of the following: v Cycle power via the POWER button on the Autoloader. v Click RESET under the Maintenance in the RMU interface. Attention: It is recommended to always leave the skip network settings box checked (On) if the IP, Mask and Gateway addresses are to remain constant for the same Autoloader. Anytime an Autoloader needs to be replaced, the original network settings must first be installed manually using the OCP in order for the RMU to connect to a browser. At that point, after connection is made, the remaining saved VPD values can be restored via the RMU. Verify via the OCP that all configuration values are correct. If not, cycle power again.
136
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Maintenance Menu
The Maintenance Menu allows the Administrator to access Operations, General Diagnostic, Firmware, and Reset functions. The Advanced Diagnostic functions can be accessed by Authorized IBM Service Personnel only. To expand the menu, click on the +. |
This menu item displays the Operations table and the Media Status table. The Operations table contains the following: v In the left column, select one of the following maintenance operation: Reinitialize library controller Perform inventory scan Load cartridge into drive Unload cartridge from drive Import to slot Export from slot Perform clean process Perform drive upgrade Bulk Exchange v In the right column, select the slot to use for the operation. Only the slots that are valid for the chosen operation can be selected. v Click EXECUTE to begin the diagnostic. For more information on the Media Status table, see Media (Models L28/L38/L3H and F28/F38/F3H) on page 129.
137
This menu item displays the General Diagnostic table and the Media Status table. The General Diagnostic table contains the following: v Select one of the following diagnostic operations from the drop-down box: Library Verify Test System Test v Enter the number of cycles to run the operation. Click EXECUTE to begin the diagnostic. Click STOP to terminate the diagnostic. For more information on the Media Status table, see Media (Models L28/L38/L3H and F28/F38/F3H) on page 129.
138
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
This menu item displays the Firmware table which contains the following: v Update Autoloader Firmware: Enter the filename or browse to the file on your server (host) and click UPDATE to load the new firmware onto the Autoloader. v Update Drive Firmware: Enter the filename or browse to the file on your server (host) and click UPDATE to load the new firmware onto the Autoloaders drive. A pop-up box will appear asking Are you sure? Click OK to initiate the firmware update. Click CANCEL to return to the Firmware table. |
This menu item displays the Autoloader Reset table which contains a RESET button. Clicking this button restarts the Autoloader and the RMU connection can be lost. Reload the RMU interface and navigate back to the Autoloader Reset table by clicking on Reset in the Maintenance Menu in the left frame. A pop-up box will appear asking Are you sure? Click OK to initiate the reset. Click CANCEL to return to the Autoloader Reset table.
139
Logs Menu
The Logs Menu allows the Administrator to access and configure Autoloader and Drive log information. To expand the menu, click on the +. |
This menu item displays the Autoloader Logs table which contains the following: v Log Type: Select the type of Autoloader log to be displayed. v Total number of entries: Displays the current number of Autoloader log entries. v Start entry: Enter a number for the first Autoloader log entry. v Number of entries per page: Enter the number of Autoloader log entries that should appear on a page. v Update: Click SUBMIT to update the Autoloader log with the new settings. v Clear log: Click OK to clear the Autoloader log. v Dump log: Click OK to copy the Autoloader log to a file on your server (host).
140
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
This menu item displays the tape drive Logs table which contains the following: v Log Type: Select the type of drive log to be displayed. v Total number of entries: Displays the current number of drive log entries. v Start entry: Enter a number for the first drive log entry. v Number of entries per page: Enter the number of drive log entries that should appear on a page. v Update: Click SUBMIT to update the drive log with the new settings. v Dump log: Click OK to copy the drive log to a file on your server (host).
141
Logout
To logout of the RMU, click on the small icon to the right of Login in the upper right corner of the screen above the Quick Status table.
142
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Media
Attention LTO Ultrium Tape Cartridges are delicate components and require care in handling. Before using the media, be sure to read Handling Cartridges on page 147. The Ultrium 3 and Ultrium 2 Tape Drive is compatible with the cartridges of its predecessor, the Ultrium 1 Tape Drive. When labeled according to proper IBM bar code label specifications (see Bar Code Label on page 145), the last character of the cartridges volume serial number (VOLSER) indicates the generation of the media. For example, a cartridge with a VOLSER of 000764L2 is an Ultrium 2 cartridge; a cartridge with a VOLSER of 003995L1 is an Ultrium 1 cartridge. Table 12 shows Ultrium data and cleaning cartridge compatibility with Ultrium Tape drives: | | | | | | | |
IBM Ultrium Tape Drive Ultrium 3 Ultrium 2 Ultrium 1 Table 12. Ultrium data and cleaning cartridge compatibility with Ultrium tape drives IBM TotalStorage LTO Ultrium Data Cartridges 400 GB (Ultrium 3) Read/Write 200 GB (Ultrium 2) Read/Write Read/Write 100 GB (Ultrium 1) Read only Read/Write Read/Write
Figure 114 on page 144 shows the TotalStorage LTO Ultrium 200 GB Data Cartridge and its components.
143
Figure 114. The IBM TotalStorage LTO Ultrium 200 GB Data Cartridge
1 2 3
4 5 6
In addition to using LTO Ultrium 3 Tape Cartridges with up to 400 GB capacity and Ultrium 2 Tape Cartridges with up to 200 GB capacity, the Ultrium 3 tape drive reads to certified LTO Ultrium Tape Cartridges that have capacities of 100 GB. If you want to control the capacity of the cartridge (for example, if you want to limit the capacity to obtain a faster seek time) you can do so by issuing the SCSI command SET CAPACITY. For information about this command, refer to the IBM TotalStorage Ultrium Tape Drive SCSI Reference at http://www.ibm.com/storage/support/lto/. To ensure that your tape library conforms to IBMs specifications for reliability, use only IBM LTO Ultrium Tape Cartridges. You may use other LTO-certified data cartridges, but they may not meet the standards of reliability established by IBM. The IBM TotalStorage LTO Ultrium 200 GB Data Cartridge cannot be interchanged with the media used in other IBM non-LTO Ultrium tape products.
Data Cartridge
| | | | | | | | | | | | The IBM Ultrium 3 Data Cartridge is slate blue, the IBM Ultrium 2 Data Cartridge is purple, and the Ultrium 1 Data Cartridge is black. All generations contain 1/2-inch, dual-coat, metal-particle tape. The Ultrium 1 cartridge has a native data capacity of 100 GB (200 GB at 2:1 compression); the Ultrium 2 cartridge has a native data capacity of 200 GB (400 GB at 2:1 compression); and, the Ultrium 3 cartridge has a native data capacity of 400 GB (800 GB at 2:1 compression). When processing tape in the cartridges, the Ultrium Tape Drives use a linear, serpentine recording format. The Ultrium 1 drive reads and writes data on 384 tracks, 8 tracks at a time; the Ultrium 2 drive reads and writes data on 512 tracks, 8 tracks at a time; and the Ultrium 3 drive reads and writes data on 704 tracks, 16 tracks at a time for generation 3 media and 8 tracks at a time for generation 1 or 2 media. The first set of eight tracks is written from near the beginning of the tape to
144
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | |
near the end of the tape. The head then repositions to the next set of eight tracks for the return pass. This process continues until all tracks are written and the tape is full, or until all data is written. All generations of the IBM LTO Ultrium Data Cartridge includes a Linear Tape-Open Cartridge Memory (LTO-CM) chip ( 1 in Figure 114 on page 144), which contains information about the cartridge and the tape (such as the name of the manufacturer that created the tape), as well as statistical information about the cartridges use. Whenever you unload a tape cartridge, the Autoloader writes any pertinent information to the cartridge memory. The cartridge door ( 2 in Figure 114 on page 144) protects the tape from contamination when the cartridge is out of the drive. Behind the door, the tape is attached to a leader pin 3 . When you insert the cartridge into the drive, a threading mechanism pulls the pin (and tape) out of the cartridge, across the drive head, and onto a non-removable takeup reel. The head can then read or write data from or to the tape. The write-protect switch 4 prevents data from being written to the tape cartridge. The label area 5 provides a location for you to place a label. Affix only a bar code label or a human-writable label. When affixing a label, place it only in the recessed label area. A label that extends outside of the recessed area can cause loading problems in the internal drive or in the Autoloader. The VOLSER on a cleaning cartridges bar code label must begin with CLN or the library treats the cleaning cartridge as a data cartridge during an inventory. The insertion guide 6 is a large, notched area that prevents you from inserting the cartridge incorrectly. You can order tape cartridges with the bar code labels included, or you can order custom labels. To obtain tape cartridges and bar code labels, see Ordering Media Supplies on page 159. The bar code and bar code label must meet predefined specifications. To determine the specifications, visit the web at http://ssddom02.storage.ibm.com/tape/lto/documentation/labelspec.pdf or contact your IBM Marketing Representative. Both generations of the LTO Ultrium Data Cartridge have a nominal cartridge life of 5000 load and unload cycles.
Cleaning Cartridge
The drive determines when it needs to be cleaned and alerts the library and the servers (hosts) application software. The user is required to select CLEAN DRIVE in the Commands Menu to initiate cleaning. See CLEAN DRIVE on page 58. | | All generations of the LTO Ultrium Cleaning Cartridge are valid for 50 uses. A cartridges LTO-CM chip tracks the number of times the cartridge has been used.
145
does not contain a label, the bar code scanner will treat that slot as empty. In addition, the bar code includes the two-character media-type identifier Lx, where x equals 1 or 2. L identifies the cartridge as an LTO cartridge. 1 indicates that the cartridge is the first generation of its type; 2 indicates that the cartridge is the second generation of its type. Figure 115 shows a sample bar code label for the LTO Ultrium Tape Cartridge. You can order tape cartridges with the labels included, or you can order custom labels. To order tape cartridges and bar code labels, see Ordering Media Supplies on page 159. The bar code must meet predefined specifications. To determine the specifications of the bar code and the bar code label, visit the web at http://ssddom02.storage.ibm.com/tape/lto/documentation/labelspec.pdf or contact your IBM Marketing Representative. When attaching a bar code label to a tape cartridge, place the label only in the recessed label area (see 5 in Figure 114 on page 144). A label that extends outside of the recessed area can cause loading problems in the drive or the library. Attention: Do not place any type of mark on the white space at either end of the bar code. A mark in this area may prevent the Autoloader from reading the label.
Figure 115. Sample bar code label on the LTO Ultrium Tape Cartridge. The volume serial number (LTO123L2) and bar code are printed on the label.
146
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
v With light finger pressure, smooth the label so that no wrinkles or bubbles exist on its surface. v Verify that the label is smooth and parallel, and has no roll-up or roll-over. The label must be flat to within 0.5 mm (0.02 in.) over the length of the label and have no folds, missing pieces, or smudges. v Do not place other machine-readable labels on other surfaces of the cartridge. They may interfere with the ability of the bar code scanner to read the bar code.
1
Figure 116. Setting the write-protect switch
Handling Cartridges
Attention Do not insert a damaged tape cartridge into your Autoloader. A damaged cartridge can interfere with the reliability of a drive and may void the warranties of the drive and the cartridge. Before inserting a tape cartridge, inspect the cartridge case, cartridge door, and write-protect switch for breaks.
A67E0026
147
Incorrect handling or an incorrect environment can damage the IBM LTO Ultrium Tape Cartridges or their magnetic tape. To avoid damage to your tape cartridges and to ensure the continued high reliability of your IBM LTO Ultrium Tape Drive, use the following guidelines:
Provide Training
v Post procedures that describe proper media handling in places where people gather. v Ensure that anyone who handles tape has been properly trained in handling and shipping procedures. This includes operators, users, programmers, archival services, and shipping personnel. v Ensure that any service or contract personnel who perform archiving are properly trained in media-handling procedures. v Include media-handling procedures as part of any services contract. v Define and make personnel aware of data recovery procedures.
v Never ship a cartridge in a commercial shipping envelope. Always place it in a box or package. v If you ship the cartridge in a cardboard box or a box of a sturdy material, ensure the following:
148
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Place the cartridge in polyethylene plastic wrap or bags to protect it from dust, moisture, and other contaminants. Pack the cartridge snugly; do not allow it to move around. Double-box the cartridge (place it inside a box, then place that box inside the shipping box) and add padding between the two boxes (see Figure 118).
Attention When inspecting a cartridge, open only the cartridge door. Do not open any other part of the cartridge case. The upper and lower parts of the case are held together with screws; separating them destroys the usefulness of the cartridge. __ Step 1. Inspect the cartridges packaging to determine potential rough handling. __ Step 2. Inspect the cartridge for damage before using or storing it.
149
__ Step 3. Inspect the rear of the cartridge (the part that you load first into the tape load compartment) and ensure that there are no gaps in the seam of the cartridge case (see 1 in Figure 119). If there are gaps in the seam, the leader pin may be dislodged. Go to Repositioning or Reattaching a Leader Pin on page 152.
__ Step 4. Check that the leader pin is properly seated. __ Step 5. If you suspect that the cartridge has been mishandled but it appears useable, copy any data onto a good cartridge immediately for possible data recovery. Discard the mishandled cartridge.
150
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
__ Step 2. Use the IBM Leader Pin Reattachment Kit (part number 08L9129) to correctly seat the pin (see Ordering Media Supplies on page 159). Then, immediately use data recovery procedures to minimize chances of data loss. Example: Split Cartridge Case The cartridges case is damaged. There is a high possibility of media damage and potential loss. Perform the following steps: __ Step 1. Look for cartridge mishandling. __ Step 2. Use the IBM Leader Pin Reattachment Kit (part number 08L9129) to correctly seat the pin (see Reattaching a Leader Pin on page 154). Then, immediately use data recovery procedures to minimize chances of data loss. __ Step 3. Review media-handling procedures (see Handling Cartridges on page 147.
151
Figure 120. Leader pin in the incorrect and correct positions. The cartridge door is open and the leader pin is visible inside the cartridge.
To reposition the leader pin, perform the following steps. 1. Slide open the cartridge door ( 1 in Figure 121 on page 153) and locate the leader pin 2 (you may need to shake the cartridge gently to roll the pin toward the door).
152
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
2. With plastic or blunt-end tweezers, grasp the leader pin and position it in the pin-retaining spring clips 3 . 3. Press the leader pin gently into the clips until it snaps into place and is firmly seated. Ensure that there are no gaps in the seam of the cartridge 4 .
Attention If gaps exist, do not continue with this procedure and do not use the cartridge. 4. Close the cartridge door.
Figure 121. Placing the dislodged leader pin into the correct position. The cartridge door is open to show the leader pin.
5. To rewind the tape, insert the cartridge manual rewind tool ( 1 in Figure 122) into the cartridges hub 2 and turn it clockwise until the tape becomes taut.
153
Attention v Use only the IBM Leader Pin Reattachment Kit to reattach the leader pin to the tape. Other methods of reattaching the pin will damage the tape, the drive, or both. v Use this procedure on your tape cartridge only when the leader pin detaches from the magnetic tape and you must copy the cartridges data onto another cartridge. Destroy the damaged cartridge after you copy the data. This procedure may affect the performance of the leader pin during threading and unloading operations. v Touch only the end of the tape. Touching the tape in an area other than the end can damage the tapes surface or edges, which may interfere with read or write reliability.
2 3
The following procedure describes how to reattach a leader pin. To reattach a leader pin by using the IBM Leader Pin Reattachment Kit: 1. Attach the leader pin attach tool ( 1 in Figure 124 on page 155) to the cartridge 2 so that the tools hook 3 latches into the cartridges door 4 . Pull the tool back to hold the door open, then slide the tool onto the cartridge. Open the tools pivot arm 5 .
154
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
A67E0042
Figure 124. Attaching the leader pin attach tool to the cartridge. To hold the cartridge door open, hook the tool into the door and pull the tool back.
2. To find the end of the tape inside the cartridge, attach the cartridge manual rewind tool ( 1 in Figure 125 on page 156) to the cartridges hub 2 by fitting the tools teeth between the teeth of the hub. Turn the tool clockwise until you see the end of the tape inside the cartridge. Then, slowly turn the rewind tool counterclockwise to bring the tape edge toward the cartridge door 3 . 3. Continue to turn the rewind tool counterclockwise until approximately 13 cm (5 in.) of tape hangs from the cartridge door. If necessary, grasp the tape and pull gently to unwind it from the cartridge. 4. Remove the rewind tool by pulling it away from the cartridge. Set the tool and the cartridge aside.
155
Figure 125. Winding the tape out of the cartridge. Turn the cartridge manual rewind tool clockwise to see the end of the tape, then turn it counterclockwise to bring the tape to the cartridge door.
5. On the leader pin ( 1 in Figure 126), locate the open side of the C-clip 2 . The C-clip is a small black part that secures the tape 3 to the pin. 6. Remove the C-clip from the leader pin by using your fingers to push the clip away from the pin. Set the pin aside and discard the clip.
3 1
Figure 126. Removing the C-clip from the leader pin. Use your fingers to push the C-clip from the leader pin.
7. Position the tape in the alignment groove of the leader pin attach tool (see 1 in Figure 127 on page 157). 8. Place a new C-clip into the retention groove 2 on the leader pin attachment tool and make sure that the clips open side faces up. 9. Place the leader pin (from step 6) into the cavity 3 of the leader pin attach tool.
Attention To prevent the leader pin from rolling into the cartridge, in the following step use care when folding the tape over the pin. 10. Fold the tape over the leader pin and hold it with your fingers (see Figure 127 on page 157).
156
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
A67E0036
Attention Use care to ensure that the tape is centered over the leader pin. Failure to properly center the tape on the pin will cause the repaired cartridge to fail. When the tape is properly centered, a 0.25-mm (0.01-in.) gap exists on both sides of the pin.
4 3
6 5
11. Close the pivot arm 4 of the leader pin attach tool by swinging it over the leader pin so that the C-clip snaps onto the pin and the tape. 12. Swing the pivot arm open and trim the excess tape 5 so that it is flush with the reattached leader pin 6 . 13. Use your fingers to remove the leader pin from the cavity 3 in the leader pin attach tool. 14. Use the cartridge manual rewind tool to wind the tape back into the cartridge (wind the tape clockwise). Ensure that the leader pin is latched by the pin-retaining spring clips on each end of the leader pin. 15. Remove the rewind tool. 16. Remove the leader pin attach tool by lifting its end up and away from the cartridge.
Operator Guide: Media
A67E0037
157
Attention Use a repaired tape cartridge only to recover data and move it to another cartridge. Continued use of a repaired cartridge may void the warranties of the drive and the cartridge.
158
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | | | | | | | | | | | | | | | | | | | | | | | |
IBM TotalStorage LTO Ultrium 400 GB Data Cartridge Bar code labels are pre-applied to cartridges.
IBM TotalStorage LTO Ultrium 400 GB Data Cartridge Order VOLSER labels separately.
IBM TotalStorage LTO Ultrium 200 GB Data Cartridge Order VOLSER labels separately (see Ordering Bar Code Labels on page 160). For Models L28/L38/L3H and F28/F38/F3H only.
| | | | | | |
IBM TotalStorage LTO Ultrium Cleaning Cartridge (universal cleaning cartridge for use with Ultrium 1, Ultrium 2, and Ultrium 3 drives) VOLSER labels are included.
v Order as part number 35L2086 through an IBM-authorized distributor (for the closest distributor, visit the web at http://www.ibm.com/storage/media), or v if you do not have Internet access, order the cartridge from any authorized IBM Business Partner or your IBM Sales Representative, or v call 1-888-IBM-MEDIA. Order as part number 08L9129 through an IBM-authorized distributor (for the closest distributor, visit the web at http://www.ibm.com/storage/media). Order as part number 08L9130 through an IBM-authorized distributor (for the closest distributor, visit the web at http://www.ibm.com/storage/media).
Note: Be sure to order bar code labels for all cleaning and data cartridges. TheAutoloader will not recognize cartridges without a bar code label.
Operator Guide: Media
159
160
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| |
| |
| |
Safety Inspection . . . . . . . . . . . Removing/Replacing the Autoloader . . . . Tools Required . . . . . . . . . . . Before Powering OFF the Autoloader . . . Removing the Autoloader . . . . . . . Replacing the Autoloader . . . . . . . Attaching the RID Tag . . . . . . . Installing the Replacement Autoloader . . Configuration Changes . . . . . . . Removing/Replacing the External Fan . . . . Tools Required . . . . . . . . . . . Removing the External Fan . . . . . . . Replacing the External Fan . . . . . . . Removing/Replacing the Bar Code Reader (BCR) Tools Required . . . . . . . . . . . Removing the BCR . . . . . . . . . Replacing the BCR. . . . . . . . . . Removing/Replacing the RMU . . . . . . Tools Required . . . . . . . . . . . Removing the RMU . . . . . . . . . Replacing the RMU . . . . . . . . . Removing/Replacing the HVD Converter . . . Tools Required . . . . . . . . . . . Removing the HVD Converter . . . . . Replacing the HVD Converter . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
203 204 204 204 204 205 205 206 206 208 208 208 208 210 210 210 211 212 212 212 213 214 214 214 215
| |
Parts Lists . . . . . . . . . . . . . . 217 Parts for Autoloader . . . . . . . . . . . 217 Power Cords . . . . . . . . . . . . . 218 Power Cord Information . . . . . . . . 218 Types of Plugs . . . . . . . . . . . 220
| | |
. 203
161
162
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Troubleshooting
| This chapter provides information and instructions on Autoloader and tape drive problem determination should one ever occur.
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
An Autoloader error code or error message See Resolving Error Messages/Codes on is displayed on the OCP display, in the error page 166. log, on the Host, or on the RMU display. A Drive error code or error message is displayed on the OCP display, in the error log, on the Host, or on the RMU display. The Error (red) LED on the OCP is ON. A TapeAlert Message from the host. The Media Attention (amber) LED on the OCP is ON. See Resolving Error Messages/Codes on page 166. See Resolving Error Messages/Codes on page 166. See TapeAlert Flags on page 227. See OCP Media Attention LED / Tape Drive Error Codes on page 166 - OR -Tape Unload/Export Problems Procedure on page 199.
The Clean Drive (amber) LED on the OCP is Perform the Clean Drive procedure. See ON. CLEAN DRIVE on page 58. The Autoloader does not power ON or the Power (green) LED on the OCP is OFF. No air flow from the cooling fan in the Autoloader. The OCP display is blank, hung, or frozen. See Power/External Fan Analysis Procedure on page 197. See Power/External Fan Analysis Procedure on page 197. Gather all failure information available, ensure that power is being applied to the Autoloader, cycle the power OFF then ON, load the latest level of firmware, if possible. If the OCP display is still failing, replace the Autoloader.
163
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
Table 17. Start Here (continued) If You Are Here for This Reason... A tape is stuck in the drive, or a cartridge is stuck in the autoloader. Perform This Action... See Tape Unload/Export Problems Procedure on page 199 -OR-(IBM Service Personnel Only) See Removing a Cartridge Manually on page 266 or Manually Removing a Tape Cartridge from an Ultrium 1 or 2 Drive on page 270. See Repositioning or Reattaching a Leader Pin on page 152. See Drive Error Codes on page 179. Use Error Code 6, Tape Drive or Media Error, or Error Code 7, High Probability of Media Error. If the tape is stuck, see Tape Unload/Export Problems Procedure on page 199. See Running a Fibre Channel Wrap Test on page 73. See Fixing Drive SCSI Bus Errors on page 239. 1. Clean the drive. See CLEAN DRIVE on page 58. 2. Run NORMAL R/W TEST on page 71. Suspected firmware (microcode) problem. Update the firmware. See Step 5. Update Firmware on page 111. For drive firmware problems, see Drive Error Codes on page 179. Use Error Code 3 or 4. If new firmware does not resolve the problem, contact IBM Technical Support. See Step 5. Update Firmware on page 111. See Copying Autoloader Error Log and Trace Log Files to the Server (Host) on page 193. See Copying a Drive Dump Log to Server (Host) on page 185. See PRESERVE DUMP (LTO-3 only) on page 74. See Messages on page 233. See Removing/Replacing the Autoloader on page 204. -OR-See Removing/Replacing the External Fan on page 208. -OR-See Removing/Replacing the Bar Code Reader (BCR) on page 210. -OR-See Removing/Replacing the RMU on page 212. -OR-See Removing/Replacing the HVD Converter on page 214. See LOADER DIAG on page 67.
Fibre Channel service or error messages from the host. SCSI errors from the host. Excessive temporary errors reported to the host.
Update firmware (microcode) on the Autoloader or drive. Copy the Autoloader Error log or Trace log to the host. Copy the drive firmware dump to the host. Preserve the drive firmware dump before replacing the Autoloader. Obtain drive or Autoloader error information at the server (host). Remove/replace Customer Replaceable Units (CRUs).
164
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | | | | | | | | | |
Table 17. Start Here (continued) If You Are Here for This Reason... Run drive diagnostic tests. Analyze suspected RMU problems. Analyze suspected BCR problems. Analyze suspected HVD Converter problems. Contact IBM Technical Support. Perform This Action... See DRIVE DIAG on page 70. See RMU Analysis Procedure on page 198. See BCR Analysis Procedure on page 198. See HVD Converter Analysis Procedure on page 199. See Pre-call Checklist on page 200 and Contacting IBM Technical Support on page 200. See Safety Inspection on page 203.
165
166
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | | | | | | | | | | | | |
Viewing Drive Error Codes via Serial Communication: 1. From the TSMON> prompt, login (lgi) as admin (Administrator needs appropriate password). 2. From the TSMON> prompt, type drv1 (display drive error log). 3. The entire drive error log table will display (up to ten errors if ten are available). 4. The first byte in the string of five bytes will contain the drive error code. The drive error code is displayed in ASCII. For example, if the single hex drive error code is a 7 (media error), the representation displayed in the drive error log table will show a 37. The remaining four bytes on each line are development information and can be ignored. The most recent drive error code is on line one. Viewing Drive Error Codes via the RMU: 1. Login as Administrator. 2. Click on Logs and then Drive. 3. The drive error log table described for serial communication is displayed.
167
The following is an example for an error/event log display: EVENT 6 80 93 0B 20 Sequence number 6 indicates the position in the sequence list, 0 being the most recent. In this example, the log shows a load error: v Type 80 = Unrecovered error v Code 93 = Load error v Internal error 0B = Door Stop v Cmd 20 = Load After pressing Enter, the associated time stamp will be displayed in the following format: ddd:hh:mm:ss:HH ddd: days hh: hours mm: minutes ss: seconds HH: 1/100 second The time stamp is set at zero at system start up. The complete Error Log can be printed out also through the Serial Monitor or the optional RMU. For more information on the Serial Monitor, see Using Serial Port Communications on page 259. For more information on the RMU, see Remote Management Unit (RMU) on page 123.
168
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Different sub code classes are joined to the main errors. In the following tables, the specific sub code class is defined in the error description. To get the correct sub code, look in the associated sub code class table.
| |
| |
1Ch 1Dh-1Fh
169
Table 20. Recovered Errors 20h - 2Fh (continued) Error Code 21h 22h-2Fh SCSI parity error Reserved Description
55h 56h
170
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 22. Illegal Request Errors 50h - 6Fh (continued) Error Code 57h 58h 59h 5Ah 5Bh 5Ch 5Dh 5Eh 5Fh 60h 61h 62h 63h 64h 65h 66h 67h 68h 69h 6Ah 6Bh 6Ch 6Dh 6Eh 6Fh Invalid drive specified Invalid test number at diagnostic Invalid offset on write buffer Invalid size on write buffer Bad controller image checksum Invalid LUN Parameter list error: Invalid field Parameter list error: Parameter not supported Parameter value invalid Saving parameters not supported Cleaning slot empty Cleaning slot doesnt have a cleaning tape SCSI invalid ID message Media Load/Eject failure Destination element full Source slot or drive empty Unrecognized loader command Wrong header length Bad sequence number Wrong checksum Command unspecified Configuration Problem: No Bar Code Reader installed Flash image does not fit boot code Medium removal prevented by drive Firmware image contains wrong personality Description
Description
171
Table 24. Additional Errors 7Ah - 7Fh (continued) Error Code 7Eh 7Fh Description Reservation conflict status Reserved
Error 80h
Table 25. Error 80h Error Code 80h Description No error. Action No action required.
82h
Device Status not suitable to Retry operation. After several execute this command. occurrences, contact IBM Technical Support. If the Autoloader is busy, some commands cannot be executed at the same time. This error will indicate a probable conflict. This is not an error condition, but does result in reporting a busy condition to the server (host) for the requested SCSI command. Inventory not valid. The cartridge inventory is not valid, because of manual changes or previous fatal errors. In such case, the inventory must be updated by the appropriate Set Slot Status commands. Source element not ready. Transport source element does not have the expected state. Destination element not ready. Destination element does not have the expected state. Perform an inventory rescan (Menu item COMMANDS / RE-INVENTORY.
83h
84h
Perform an inventory rescan (Menu item COMMANDS / RE-INVENTORY. Perform an inventory rescan (Menu item COMMANDS / RE-INVENTORY.
85h
86h
Assigned to a rejected user attempt Finish IMPORT/EXPORT, to access door while media afterwards retry operation. removal is prevented. Is used for several robotic command timeout conditions. Timeout detected by Autoloader on system testing Reset the unit (Menu item CONFIGURATION / RESET). Reset the unit (Menu item CONFIGURATION / RESET), restart System Test.
87h 89h
172
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 26. Robotic Control Errors 81h - 8Fh (continued) Error Code 8Fh Description Action
91h
92h
93h
94h
Cartridge dismount error. Failure during cartridge removal and transport back to the slot.
95h
Import error. Run Library Verify Test (menu Device wasnt able to finish import item DIAGNOSTICS / LOADER of new cartridge without error. DIAG. / LIBRARY VERIFY), after further occurrences, contact IBM Technical Support. Export error. Run Library Verify Test (menu Fatal error during cartridge export. item DIAGNOSTICS / LOADER DIAG. / LIBRARY VERIFY), after further occurrences, contact IBM Technical Support. Reserved
96h
97h-9Fh
173
A1h
A2h
A3h
A4h
Door function error. Slider door in front bezel not in requested position during device operation. Fan error. Autoloader has detected a fan error. Sub code: v F1: Fan at backplane was the originator v F2: Fan at drive was the originator v F3: Both fans are defective
A5h
A6h-AFh
Reserved
B1h B2h
174
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 29. Electronic Hardware Errors B0h - B9h (continued) Error Code B5h B6h B7h B8h Description Display error. A defective Display was detected. Memory error. A defective Memory was detected. Fatal system error Bar code error Action Contact IBM Technical Support. Contact IBM Technical Support. Contact IBM Technical Support. Perform an inventory rescan (Menu item COMMANDS / RE-INVENTORY). After several occurrences, replace Bar Code Reader. Contact Technical Support
B9h
Database Error
BCh
Over temperature problem. Sub code: The original drive error code is reported (refer to Table 35 on page 179). No connection to drive. Drive Failure Sub code: The original drive error code is reported (refer to Table 35 on page 179).
BDh
| | |
BFh
| | | | | | | |
C1h-CFh
175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | |
D1h
D2h
Webserver Error
D3h
D4h
No RMU found
D5h
F1h
F2h
Subcode Descriptions
Table 34. Subcode Descriptions Error Code Description No subcode error Communication timeout Length expired before expected character received
176
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 34. Subcode Descriptions (continued) Error Code 03h 10h 11h 12h 13h 14h 15h 16h 17h 18h 21h 22h 23h 24h 25h 26h 27h 28h 29h 2Ah 2Bh 2Ch 2Dh 2Eh 2Fh 30h 31h 32h 33h 35h 36h 37h 38h 39h 40h 41h Description Any other kind of driver error Start pattern missing Sequence enumeration error Packet length error Checksum mismatch End pattern missing Drive busy - command rejected General drive error Byte stuffing error Command negative acknowledged Carrier state error. Repetitions error. Number of repetitions reached. Move to slot position repetitions error. Number of repetitions at move to slot reached. Move to eject position repetitions error. Number of repetitions at mvoe to eject position reached. Belt start error. Start of belt motor unsuccessful. Belt backward start error. Start of belt motor unsuccessful. Belt home error. Home carrier at move to home position not found. Unexpected belt home error. Unexpected home carrier detected at belt movement. Belt door stop error. Belt stopped by door opening. Belt position error at move to carrier 1 (home slot) Belt position error at move to carrier 2 Belt position error at move to carrier 3 Belt position error at move to carrier 4 Belt position error at move to carrier 5 Belt position error at move to carrier 6 Belt position error at move to carrier 7 Belt position error at move to carrier 8 Belt position error at move to carrier 9 (optional) Belt position error at move to carrier 10 (optional) Gripper start error. Start of gripper motor unsuccessful Gripper open error. Gripper open position not reached. Gripper close error. Gripper close position not reached. Gripper hold error. Gripper hold/closed position not reached. Gripper unexpected closed error. Gripper closed although a cartridge should be there. Slider start error. Start of slider motor unsuccessful. Slider home error. Slider home position not reached.
177
Table 34. Subcode Descriptions (continued) Error Code 42h 43h 44h 45h 46h 47h 48h 49h 4Ah 4Bh 4Ch 4Dh 50h 51h Description Slider forward positioning error. Slider position in forward direction not reached. Slider complex forward positioning error. Slider position in a complex forward movement not reached. Slider backward positioning error. Slider position in backward direction not reached. Slider complex backward positioning error. Slider position in a complex backward movement not reached. Slider lost steps at forward movement. Slider lost steps at complex forward movement. Slider lost steps at backward movement. Slider lost steps at complex backward movement. Wrong slider start position at forward movement. Wrong slider start position at complex forward movement. Wrong slider start position at backward movement. Wrong slider start position at complex backward movement. Door open error. Door open position not reached. Door close error. Door close position not reached. Door repetitions error. Door close repetitions not reached. Axis initialization error. Initialization of all axis not successful. Unknown cartridge error. Door close error at import/export. Wrong source carrier state. Wrong destination carrier state. Multiple carrier state. Expected cartridge in transit not found. Unexpected cartridge in transit found. Drive wake up failed. Error accessing the slot status in System Database. The Robotic load operation could not reach the cartridge present position. No drive activity after the load operation. Timeout while loading cartridge. No drive activity after the unload operation. Timeout while unloading cartridge. Drive unload operation terminated unsuccessfully Robotic could not detect an ejected cartridge at unload operation No slot was free at Robotic unload operation.
52h 60h 70h 71h 72h 73h 74h 75h 76h 81h 88h 90h 91h 92h 93h 94h 95h 96h 97h
178
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | | | | | | | |
Attention If the tape drive detects a permanent error and displays an error code other than 0, it automatically performs a drive firmware dump. If you force a drive dump, the existing dump will be overwritten and error information will be lost. Do not switch OFF power to the Autoloader or the dump data will be lost. (For Ultrium 3 drives only) If the error code action procedure leads to replacement of the Autoloader, it is very important to preserve the active dump information in non-volatile storage before switching the library power OFF. This dump information will be used by the Repair Center when they perform failure analysis on the returned drive. Perform PRESERVE DUMP (LTO-3 only) on page 74 before powering OFF the drive.
Table 35. Drive error codes. A drive error code appears in the OCPs display of the Autoloader. It clears when you power-off the unit. Code 0 Cause and Action No error occurred and no action is required. This code displays: v When power is cycled (turned off, then on) to the Autoloader. v When diagnostics have finished running and no error occurred. 1 Cooling problem. The tape drive detected that the recommended operating temperature was exceeded. Perform one or more of the following actions: v Ensure that the cooling fan is rotating and is quiet. If not, replace the external fan. v Remove any blockage that could prevent air from flowing freely through the Autoloader. v Ensure that the operating temperature and airflow is within the specified range (see Table 7 on page 16). v If the operating temperature is within the specified range and the problem persists, replace the Autoloader. The error code clears when you power-off the Autoloader or access the Diagnostic Menu (see Diagnostic Menu on page 67). 2 Power problem. The tape drive detected that the externally supplied power is either approaching the specified voltage limits (the Autoloader is still operating) or is outside the specified voltage limits (the Autoloader is not operating). Perform the following action: 1. Ensure that the power connector is properly seated. 2. Ensure that the proper AC voltages are being applied within the tolerances allowed (see Table 5 on page 15). 3. If the proper voltages are being applied but the problem persists, replace the Autoloader. The error code clears when you power-off the Autoloader or access the Diagnostic Menu (see Diagnostic Menu on page 67).
| |
179
Table 35. Drive error codes (continued). A drive error code appears in the OCPs display of the Autoloader. It clears when you power-off the unit. Code 3 Cause and Action Firmware problem. The tape drive determined that a firmware error occurred. Perform the following action: 1. Collect a drive dump from one of the following: Note: Do not force a new dump; the Autoloader has already created one. v Servers SCSI interface by using a device driver utility or system tool (for instructions about reading a drive dump from tape, visit the web at http://www.ibm.com/storage/lto) v Ultrium Tape Drive (to copy a drive dump, see Copying a Drive Dump Log to Server (Host) on page 185) 2. Power the Autoloader off and on, then retry the operation that produced the error. 3. If the problem persists, download new firmware and retry the operation.
| |
4. If the problem persists, contact your IBM Technical Support Center and send the drive dump (that you collected in Step 1) to them. The error code clears when you power-off the Autoloader or access the Diagnostic Menu (see Diagnostic Menu on page 67). 4 Firmware or tape drive problem. The tape drive determined that a firmware or tape drive hardware failure occurred. Perform the following action: 1. Collect a drive dump from one of the following: Note: Do not force a new dump; the Autoloader has already created one. v Servers SCSI interface by using a device driver utility or system tool (for instructions about reading a drive dump from tape, visit the web at http://www.ibm.com/storage/lto) v Ultrium Tape Drive (to copy a drive dump, see Copying a Drive Dump Log to Server (Host) on page 185). 2. Power the Autoloader off and on, then retry the operation that produced the error. The error code clears when you power-off the autoloader or access the Diagnostic Menu (see Diagnostic Menu on page 67).
| | | | |
5
3. If the problem persists, run the Normal (Long) R/W Test. (See NORMAL R/W TEST on page 71.) v If the test FAILED, contact IBM Technical Support and replace the Autoloader. v If the test PASSED, ensure that you have installed the latest level of firmware, then contact IBM Technical Support and send the drive dump (that you collected in Step 1) to them. Tape drive hardware problem. The drive determined that a tape path or read/write error occurred. To prevent damage to the drive or tape, the Autoloader will not allow you to insert a cartridge if the current cartridge was successfully ejected. If the problem persists, replace the Autoloader. The error code clears when you power-off the Autoloader or access the Diagnostic Menu (see Diagnostic Menu on page 67).
180
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 35. Drive error codes (continued). A drive error code appears in the OCPs display of the Autoloader. It clears when you power-off the unit. Code 6 Cause and Action Tape drive or media error. The tape drive determined that an error occurred, but it cannot isolate the error to faulty hardware or to the tape cartridge. Perform the following action: For Problems with Writing Data: If the problem occurred while the Autoloader was writing data to the tape, and if you know the volume serial number (located on the cartridge label) of the tape cartridge loaded in the drive when the problem occurred, retry the operation with a different cartridge: v If the operation succeeds, the original cartridge was defective. Copy data from the defective cartridge and discard it. v If the operation fails and another Autoloader is available, insert the cartridge into the other unit and retry the operation. If the operation fails, discard the defective cartridge. If the operation succeeds, insert a scratch cartridge into the first unit and run the Normal (Long) R/W Test (see NORMAL R/W TEST on page 71). - If the diagnostics fail, replace the Autoloader. - If the diagnostics succeed, the error was temporary. v If the operation fails and another Autoloader is not available, insert a scratch cartridge into the unit and run the Normal (Long) R/W Test (see NORMAL R/W TEST on page 71). If the diagnostics fail, replace the Autoloader. If the diagnostics succeed, discard the cartridge that caused the problem. If the problem occurs with multiple tape cartridges or if you do not know the tape cartridges volume serial number, run the Normal (Long) R/W Test (see NORMAL R/W TEST on page 71). v If the diagnostics fail, replace the Autoloader. v If the diagnostics succeed, run the Head Test diagnostic (see DRIVE DIAG on page 70). If the Head Test diagnostic fails, replace the Autoloader. If the Head Test diagnostic succeeds, replace the cartridges that caused the problem. For Problems with Reading Data: If the problem occurred while the Autoloader was reading data from the tape, and if you know the volume serial number of the tape cartridge, perform one of the following procedures: v If another Autoloader is available, insert the cartridge into the other unit and retry the operation: If the operation fails, discard the defective cartridge. If the operation succeeds, insert a scratch cartridge into the first unit and run the Normal (Long) R/W Test (see NORMAL R/W TEST on page 71). - If the diagnostics fail, replace the Autoloader. - If the diagnostics succeed, the error was temporary. v If another autoloader is not available, insert a scratch cartridge into the unit and run the Normal (Long) R/W Test (see NORMAL R/W TEST on page 71). If the diagnostics fail, replace the Autoloader. If the diagnostics succeed, discard the cartridge. If the problem occurs with multiple tape cartridges or if you do not know the tape cartridges volume serial number, run the Normal (Long) R/W Test (see NORMAL R/W TEST on page 71). v If the diagnostics fail, replace the Autoloader. v If the diagnostics succeed, run the Head Test diagnostic (see DRIVE DIAG on page 70). If the Head Test diagnostic fails, replace the Autoloader. If the Head Test diagnostic succeeds, replace the cartridges that caused the problem. The error code clears when you remove the tape cartridge or access the Diagnostic Menu (see Diagnostic Menu on page 67).
| |
| | | | | |
| | | |
| | | |
181
Table 35. Drive error codes (continued). A drive error code appears in the OCPs display of the Autoloader. It clears when you power-off the unit. Code Cause and Action A high probability of media error. The tape drive determined that an error occurred because of a faulty tape cartridge. Try another tape cartridge. If the problem only occurs with one cartridge, replace the failing cartridge. If the problem occurs with multiple tape cartridges, use the following procedure:
| | |
| | | | | | | | | |
Attention When you run the Media Test diagnostic, data on the suspect tape will be overwritten. Use only a scratch data cartridge to run the test. 1. If possible, run the tape cartridges in a different Autoloader. If the operation in the other unit fails and 6 or 7 displays, replace the media. If the operation succeeds, run the Media Test diagnostic (see DRIVE DIAG on page 70) on all the failing cartridges. 2. If the Media Test diagnostic fails, replace the media. If it runs successfully, clean the drive (see CLEAN DRIVE on page 58) and run the Normal (Long) R/W Test (see NORMAL R/W TEST on page 71). 3. If the Normal (Long) R/W Test fails, replace the Autoloader. If the Normal (Long) R/W Test runs successfully, repeat the operation that produced the original media error. The error code clears when you remove the tape cartridge or access the Diagnostic Menu (see Diagnostic Menu on page 67).
| | | | | |
Tape Drive or SCSI bus/Fibre Loop Failure. The tape drive determined that a failure occurred in the tape drives hardware or in the SCSI bus/Fibre loop. Ensure that all cables on the back of the Autoloader are seated securely and ensure that the SCSI/Loop IDs are correct. See Verifying SCSI/Loop IDs on page 197. If the problem persists, run the wrap test diagnostics. See SCSI / FIBRE WRAP TEST on page 72. Tape drive or RS-422 error. The tape drive determined that a failure occurred in the tape drives hardware or in the RS-422 connection. Replace the Autoloader. The error code clears 10 seconds after the drive detected the error or when you access the Diagnostic Menu (see Diagnostic Menu on page 67). No error or message assigned. There may be a problem with the single-character display. Turn the power off, then on and determine whether all segments on the single-character display are lit. If so, you may have a down-level version of your Autoloaders firmware or this book. Refer to the latest version of the firmware or this book. Tape drive hardware problem. The tape drive determined that a problem occurred which degraded the operation of the tape drive, but it did not restrict continued use. If the problem persists, replace the Autoloader. The drive is usable. The error code clears when you power-off the Autoloader or access the Diagnostic Menu (see Diagnostic Menu on page 67). No error or message is assigned. See error code 8 in this table. The tape drive needs to be cleaned. Clean the tape drive. See CLEAN DRIVE on page 58. The error code clears when you clean the tape drive or access the Diagnostic Menu (see Diagnostic Menu on page 67).
o, c, b, h, E, or F
d D
Fibre Channel AL_PA conflict. More than one device has the same address. Each device must have its own unique AL_PA address. No error or message assigned. See error code 0 in this table.
182
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 35. Drive error codes (continued). A drive error code appears in the OCPs display of the Autoloader. It clears when you power-off the unit. Code Cause and Action Informational message. The Fibre Channel port on the tape drive has been placed offline by another device or by an operator. This code is set when the Offline command is received from another device on the Fibre Channel interface. Determine why the device at the other end of the Fibre Channel (the server, switch, or other device) placed the drive offline. The drive is placed online when it receives the Online command from the Fibre Channel interface. After a reset, the drive comes online.
No light over Fibre Channel. The error code clears when the drive detects light or when you place the drive in maintenance mode.
183
Access Protocol
All three Autoloader communication methods (OCP, RMU, and serial) can simultaneously be active on the lowest level (Information only). v RMU: Standard user v OCP: Online v Serial: lgo (logout) However, only one of the three methods can be active at any one time on the Administrator or Service levels (RMU and serial) or at the Offline level (OCP). The other two can remain active on the lowest level. If an attempt to login is made on either of the other two while the third has the highest level access, an Already Reserved message is displayed. The RMU will only allow access by a Standard user at the login panel. For best results: v If communicating via the OCP, return to the Home Screen before attempting to communicate via the RMU or serial port. v If communicating via the RMU, log out before attempting to communicate via the OCP or serial port. v If communicating via the serial port, log out before attempting to communicate via the OCP or RMU
184
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
ITDT SCSI Firmware Update, Dump Retrieval, and Library/Drive Test Tool
Attention At the time of publication, the ITDT tool was not available. Register with MySupport (http://www.ibm.com/support/mySupport) to be notified by email when the tool becomes available, or periodically check the IBM support site (http://www.ibm.com/storage/lto). The ITDT tool offers multiple functional capabilities that simplify the task of updating tape and library firmware. It is available for most major platforms (Windows, AIX, Sun, Linux, Netware, and so on), and requires no special device drivers. This tool is similar to the LTO-TDX drive-only firmware update and dump retrieval tool described later in this chapter. Note: The ITDT tool is available on the IBM website http://www.ibm.com/storage/support/lto. In addition to the executable file (.exe), a README file will be posted on the web page. The README file describes the features and capabilities of the ITDT tool, provides downloading instructions, and gives detailed information on how to use the tool. You use the ITDT tool to perform the following tasks: v Update firmware using SCSI to all IBM LTO Tape Drive and Tape Library products (non-IBM devices may not be selected). v Upload drive and library dump files v Perform drive and library diagnostics, including drive read/write diagnostics The ITDT tool is a command line utility. To invoke it, enter the executable itdt from the directory where the tool is located. The Help feature gives a brief explanation of each function and shows the required syntax.
| | | |
LTO-TDX: LTO SCSI and Fibre Drive Firmware Download & LTO Drive Dump Upload Tool
The tool, LTO-TDX, is an alternative method for downloading LTO drive firmware across the SCSI bus or fibre channel. In addition, this tool can be used to upload LTO drive error dumps. The following information describes how to obtain the tool and lists its capabilities. 1. The tool supports all IBM LTO Gen 1 and Gen 2 SCSI and FC drives. The tool will not support any other manufacturers LTO drive. The tool is available for three different operating systems: v LTO-TDX_WinTool (for Windows operating systems) v LTO-TDX_NWTool (for Netware operating systems) v LTO-TDX_LxTool (for Linux operating systems) 2. The tool can perform two functions:
Service Guide: Troubleshooting
185
3.
4.
5.
6.
7. 8. 9.
13. 14.
a. Download firmware to the drive b. Upload a dump of the drive firmware logs from the drive to a computer system The tool is distributed from the IBM web site. Download the tool by visiting http://www.ibm.com/storage/support/lto/. The install package or an executable file will be placed on the host system in a location chosen by the user. When the user opens the install package, a license agreement will be presented. This license agreement must be accepted to proceed with the install. The user will also be presented with a license anytime the executable file is copied to another location where the firmware or dump folders do not exist. The tool will detect the missing folders at launch and present the users license, assuming that this is the first launch of a new copy of the tool. There will also be a function that allows the user to view the license at will when starting the tool. The Windows install package will create a directory for the tool on the users hard disk and place the executable file (the tool) in that directory. The install package will also load the file into the Programs Menu accessed via the Start button and put an icon on the desktop of the Windows operating system. The install package shall perform a similar function on any other operating system that has a similar structure. Selection of the icon on the desktop or selection of the tool from the Program Menu will start the tool and create the LTO Firmware and LTO Dumps files in the directory with the executable tool file. The user must first put the firmware to be downloaded in the firmware folder. Any dumps created will be put in the dump folder. The tool will present a list of the supported devices on the bus. The tool will allow selection of a target device and then perform the download or the dump on the target device. The tool itself is a command line tool but it is menu driven and very simple to use. The program displays are in English. The user is responsible to make sure the drive is not in use when firmware is downloaded or a dump is taken. The user also must remove any cartridge from the drive or the firmware download function will not work. If the user does make a mistake, the program will respond with instructive error messages. If no IBM LTO tape drives are on the bus, the tool must inform the user that there are none before closing the tool window.
186
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
6. After the firmware has been loaded into drive memory the drive automatically reboots. The tool discourages the user from power cycling the drive before the reboot is complete. A message is displayed saying Updating.....Please Wait until the reboot is complete. A progress gauge is displayed letting the user know something is still happening. 7. A Wait message is displayed on the user screen during firmware load. 8. If the program tries to load code and it fails with a sense Key 5 and an ASC/ASCQ of 82/83, the following wording is displayed: Bad Firmware Detected. The firmware is the wrong type for your tape drive or the file is corrupted. Download the file again from the IBM Web site and try the procedure again.
187
188
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0237
3. On the Connect To window: v Select the COM port that the serial cable was plugged into on the rear of your server (host). v Click OK.
a67s0238
189
4. On the COMx Properties window: v Select the following port settings: Bits per second = 38400 Data bits = 8 Parity = None Stop Bit = 1 Flow control = None v Click OK.
5. Press Enter. If you see the following window, all went well and you are able to use the Serial Monitor. If you see nothing like this or only scrambled characters, check your connection parameters.
TSMON>
7. Press Enter.
190
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0239
8. To access the administrator serial menu: a. Type lgi and press Enter.
TSMON>lgi
Note: Both the OCP and RMU must be online (logged out) before the serial port will allow login. 1) For the User ID, type admin (Administrator) or the new Adminstrator User ID set for the RMU.
TSMON>lgi User ID:admin
2) For the password, type secure (Administrator) or the new Administrator password set for the RMU.
TSMON>lgi User ID:admin Password:secure
3) Press Enter. 9. Press Enter. 10. At the next TSMON> prompt, type ddmp.
TSMON>ddmp
Note: If the Autoloader has timed out, press Enter for a fresh screen and start this procedure over. 12. In the screens toolbar, select Transfer then Receive File.... 13. On the Receive File window: v Browse to the directory on your server (host) where the file will be saved. v Select XMODEM for Use receiving protocol. v Click Receive.
191
14. On the Receive Filename window: a. Enter the desired file name under which to save the file if not already present. b. Click OK. 15. Type lgo at the TSMON> prompt to logout.
TSMON>lgo
Via RMU
To copy a drive dump log to your server (host) via the RMU, follow these instructions: 1. Navigate to the Logs Menu in the RMU. 2. Select Drive in the Logs Menu. 3. Select Error for Log Type. 4. Click on SUBMIT to update the log. 5. Click OK to Dump Log to a file on your server (host).
192
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0241
Copying Autoloader Error Log and Trace Log Files to the Server (Host)
Autoloader error and trace logs are collections of Autoloader information. These logs can be copied to your server (host) via serial communication or the RMU.
a67s0237
193
3. On the Connect To window: v Select the COM port that the serial cable was plugged into on the rear of your server (host). v Click OK.
194
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0238
4. On the COMx Properties window: v Select the following port settings: Bits per second = 38400 Data bits = 8 Parity = None Stop Bit = 1 Flow control = None v Click OK.
5. Press Enter. If you see the following window, all went well and you are able to use the Serial Monitor. If you see nothing like this or only scrambled characters, check your connection parameters.
TSMON>
7. Press Enter.
a67s0239
195
8. To access the administrator serial menu: a. Type lgi and press Enter.
TSMON>lgi
1) For the User ID, type admin (Administrator) or the new Adminstrator User ID set for the RMU.
TSMON>lgi User ID:admin
Note: Both the OCP and RMU must be online (logged out) before the serial port will allow login. 2) For the password, type secure (Administrator) or the new Administrator password set for the RMU.
TSMON>lgi User ID:admin Password:secure
3) Press Enter. Note: If the Autoloader has timed out, press Enter for a fresh screen and start this procedure over. 9. In the screens toolbar, select Transfer then Capture Text.... a. Select the path or folder and the file name desired. It is suggested to use the date in the file name and give it a .txt extension. (Example: c:\temp\mar23err-log.txt). b. Click Start.
10. At the next TSMON> prompt, type edp for an error log or tdp for a trace log.
TSMON>edp
11. Press Enter. 12. When the file completes scrolling across the monitor, click on the Transfer selection again, choose Capture Text... and then click Stop. 13. Attach the just created file to a memo and email to the desired destination. 14. Type lgo at the TSMON> prompt to logout.
TSMON>lgo
196
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Via RMU
To copy error or trace logs to your server (host) via the RMU, follow these steps: 1. Navigate to the Logs Menu in the RMU. 2. 3. 4. 5. Select Loader in the Logs Menu. Select Error or Trace as the Log Type. Click on UPDATE to update the log. Click on OK to Dump Log.
Obtaining Autoloader and Drive Error Information from Different Servers (Hosts)
For information on obtaining Autoloader and drive error information from different IBM and non-IBM servers (hosts), see Messages on page 233.
TapeAlert Flags
For a listing of TapeAlert Flags supported by the Autoloader and the tape drive, see TapeAlert Flags on page 227.
Sense Data
For information on Autoloader and drive sense data and information on using host sense data, see Sense Data on page 241.
197
| |
4. If the Autoloader power comes on, but the fan remains off, replace the rear fan (see Removing/Replacing the External Fan on page 208).
| |
198
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
v Perform a re-inventory via the OCP (see RE-INVENTORY on page 60) or view the inventory via the RMU (see Media (Models L28/L38/L3H and F28/F38/F3H) on page 129) to determine if the labels are now being read. If the BCR is still not functioning properly, replace the BCR (see Removing/Replacing the Bar Code Reader (BCR) on page 210).
Attention (For Ultrium 3 drives only) Before attempting to remove a tape from the Autoloader or drive, it is very important to preserve the active dump information in non-volatile storage in case the Autoloader has to be replaced. This dump information will be used by the Repair Center when they perform failure analysis on the returned drive. Perform PRESERVE DUMP (LTO-3 only) on page 74 before powering OFF the drive. 1. Navigate to UNLOAD CARTRIDGE in the Commands Menu and press Enter on the OCP. 2. If the cartridge will not unload from the drive, cycle the Autoloader power OFF then ON. This will force a slow rewind of the tape in the drive. It may take as long as 20 minutes for the tape to rewind and the cartridge to unload. 3. If the cartridge still will not eject from the drive, navigate to BULK EXCHANGE in the Commands Menu and remove all other cartridges from the Autoloader. 4. Replace the Autoloader. (See Pre-call Checklist on page 200 and Contacting IBM Technical Support on page 200.)
Export Problems
If a cartridge in the Autoloader will not respond to EXPORT or BULK EXCHANGE in the Commands Menu on page 55, this means that a cartridge is stuck in the Autoloader. 1. Navigate to EXPORT in the Commands Menu on page 55 and attempt to export the cartridge. 2. If the cartridge will not export, try the BULK EXCHANGE command. 3. If the cartridge still will not export from the Autoloader, replace the Autoloader. See Pre-call Checklist on page 200 and Contacting IBM Technical Support on page 200.
199
Pre-call Checklist
If you have questions or problems concerning the Autoloader, perform the following steps before placing a call to IBM Technical Support. Note: Where instructions refer you to the web, visit http://www.ibm.com/storage/support/lto/. __ Step 1. Verify that the drives firmware is at the most recent level (see Information Menu on page 49). To determine the latest release of firmware, visit the web. __ Step 2. Verify that your device drivers are at the most recent level (see your server (host) manual for instructions). v For the latest release of IBM device drivers, visit the web. v For the latest release of device drivers by independent software vendors (ISVs), visit the appropriate third-party web site. __ Step 3. Verify whether your hardware and software configuration is supported. To determine the latest supported attachments, visit the web. __ Step 4. Perform a general checkup of the hardware and connections: v Ensure that you are using the correct SCSI terminator and that you are not mistakenly using a SCSI wrap plug (used for the diagnostic SCSI wrap test). v Ensure that the SCSI cable connector does not contain bent or recessed pins. v Ensure that all retention screws for the SCSI cable and terminator are securely tightened. __ Step 5. If you still have a problem after completing the above steps, see Contacting IBM Technical Support.
| |
200
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
by the customer for damage to the failed part during shipment. Failure to fill out and affix the repair identification (RID) tag to the replacement unit with the machine type, model, and serial number of the failing unit could result in losing the warranty for the replacement unit. Before calling support, follow these steps which will help you take full advantage of your call: v Be prepared to provide Autoloader and drive firmware levels currently installed. v Review all documentation carefully. (Experience has demonstrated that most questions are answered in your documentation.) v Be prepared to explain whether the software or hardware has worked properly at anytime in the past. Have you changed anything recently? v Pinpoint the exact location of your problem, if possible. Note the steps that led to the problem. Can you duplicate the problem or is it a one-time occurrence? v Note any error messages displayed on your PC monitor or file server. Write down the exact error message. v If at all possible, call while at your computer, with the library installed and turned on. v If running on a network, have all relevant information available (that is, type, version number, network hardware, and so on). v Be prepared to provide: Your name and your companys name Model number Serial number of the library (front cover, lower right corner) Software version numbers Device driver information Host application name and version Hardware configuration, including firmware versions, date, and number Type of host, operating system version, clock speed, RAM, network type, network version, and any special boards installed A brief description of the problem Having this information available when you call for customer assistance will enable support personnel to resolve your problem in the most efficient manner possible.
201
202
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
203
Tools Required
v T10 Torx wrench or small flat-blade screwdriver | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
204
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | |
__ Step a. Remove the screws from the rack mount brackets on the Autoloader.
2-FRONT
2
a67s0208
| | | | | | |
__ Step b. Slide the Autoloader out of the rack. __ Step c. Remove the rack mount brackets from the Autoloader. __ Step d. Store the brackets and screws. __ Step 5. Remove all options installed (BCR, RMU, HVD Converter). __ Step 6. Put the Autoloader in its original packaging or similar materials. __ Step 7. Contact your sales representative or IBM Service Personnel for shipping instructions.
205
Configuration Changes
After installing the replacement Autoloader, complete the following configuration changes. If an RMU was installed on the original Autoloader and has been moved to the replacement Autoloader, proceed to Restore VPD Configuration from the RMU. If an RMU is not installed, proceed to Restore VPD Configuration from the OCP on page 207. Note: v The replacement Autoloader Administrator password will be the default password (secure). v Network settings (IP, Mask, and Gateway addresses) must be entered via the OCP before RMU communications can occur. Restore VPD Configuration from the RMU: 1. Power on the Autoloader and wait for initialization to complete. 2. Login to the RMU as Administrator. 3. Select Reset in the Configuration Menu. 4. Press the Restore Vital Product Data button. If a VPD Not Valid error message is received on the browser monitor, proceed to Restore VPD Configuration from the OCP on page 207. An error message will be received if a Save Vital Product Data was not performed as instructed in the installation instructions.
206
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
5. From the OCP or from the RMU, verify that the VPD items are correct. If any of the VPD items (see Configuring Your Autoloader on page 41) are not correct because the saved item list on the RMU was not at the latest level, proceed to Restore VPD Configuration from the OCP for the item or items that need to be corrected. 6. Resume normal operations. Restore VPD Configuration from the OCP: __ Step 1. Change the Serial Number on the replacement Autoloader with the Serial Number of your original Autoloader. This is for warranty purposes. To change the Serial Number: a. Navigate to the Configuration Menu (see Configuration Menu on page 60 [for Model L28/L38/L3H] and Configuration Menu on page 76 [for Model F28/F38/F3H]). b. Press Enter, then Next or Previous, as necessary, to access SERIAL NUMBER. c. Press Enter to display the CHANGE SER NUM screen. d. Use Next and Previous to select each digit in the new serial number. Press Enter to initiate each new digit and move to the next digit to be changed. e. Press Cancel: v One time to return to the SERIAL NUMBER screen. v Two times to return to the Configuration Menu screen. __ Step 2. For Model F28/F38/F3H, to change the World Wide Node Name: a. Refer to the Autoloader Configuration Form on page 251 that was filled out when you installed your original Autoloader for the original World Wide Node Name. b. Press Enter, then Next or Previous, as necessary, to access WW NODE NAME. c. Press Enter to display the CHANGE NODE NAME TO: OVERWRITE NN screen. d. Press Enter to access the current Node Name. e. Use Next and Previous to select each digit in the new name. Press Enter after each digit is selected to initialize the digit and move to the next digit to be changed. f. Cycle power on the Autoloader. After the power has cycled, the Home Screen will display. __ Step 3. For Model F28/F38/F3H, restore Loop ID, FC Port type, operating mode, FC Speed, and BCR enablement to the original values (see the Autoloader Configuration Form on page 251 filled out at installation time for values). Refer to Configuring a Model F28/F38/F3H Autoloader on page 99 for instructions. __ Step 4. For Model L28/L38/L3H, restore SCSI ID, operating mode, SCSI Speed, and BCR enablement to the original values (see the Autoloader Configuration Form on page 251 filled out at installation time for values). Refer to Configuring a Model L28/L38/L3H Autoloader on page 91 for instructions.
207
Figure 138. Autoloader rear panel with the External Fan removed
208
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0274
Step 6. Align thumbscrews on the fan housing with the holes on the rear panel of the Autoloader. Step 7. Tighten the thumbscrews. Step 8. Reconnect any SCSI cable or SCSI terminator to the LVD SCSI connectors 1 on the rear panel of the Autoloader. Step 9. Reconnect any serial cable connector to the serial port connector 2 . Step 10. Plug the Autoloaders power cord into the electrical outlet and the rear of the Autoloader. Step 11. Power on the Autoloader
209
3
Figure 139. Removing/replacing the BCR
Tools Required
v T10 Torx wrench or small flat-blade screwdriver
210
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0198
Follow these steps to install the BCR on the rear panel of the Autoloader: Note: See Figure 139 on page 210. __ 1. Power off the Autoloader. __ 2. Disconnect the power cord from the outlet. __ 3. Remove all cables and power cord from the rear panel of the Autoloader. __ 4. Remove the BCR cover plate ( 2 ) from the rear panel. Save the screws. Store the cover plate for future use. The cover plate will be needed if the BCR is ever removed. __ 5. Connect the cable ( 3 ) to the BCRs controller outlet. Feed the remainder of the cable back into the BCR so it will not block the BCR lens. __ 6. With the label ( 1 ) facing up, align the screw holes ( 2 ) on the BCR with the holes left by the cover plate on the rear panel of the Autoloader. __ 7. Attach the BCR with the saved screws from the cover plate. __ 8. Reconnect all cables and power cord to the Autoloader. __ 9. Power on the Autoloader. __ 10. Enable the BCR through the OCP (see BARCODE READER on page 65). Select BARCODE READER in the Configuration Menu. __ 11. Select ON in the BARCODE READER CHANGE TO: screen.
211
1
Figure 140. Removing/replacing the RMU CAUTION: Avoid contact with the card on the RMU.
Tools Required
v T10 Torx wrench or small flat-blade screwdriver
212
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0203
213
8 7 9
Figure 141. Removing/replacing the HVD Converter
6
a67s0200
214
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
__ Step 5. Remove the two thumbscrews ( 5 ) from the converter. __ Step 6. Gently pull straight back on the converter until its power connector 3 pulls free from the power receptacle 4 . __ Step 7. Put the converter in its original packaging or similar materials for storage or shipping. __ Step 8. If you are replacing the HVD Converter immediately, proceed to Replacing the HVD Converter. Otherwise, replace the cover plate over the HVD Converter opening on the Autoloaders rear panel. __ Step 9. Plug the power cord and LVD cable ( 6 ) into the rear of the Autoloader. __ Step 10. Plug the power cord into an electrical outlet. __ Step 11. Power on the Autoloader to resume operations.
215
216
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Parts Lists
Table 36 lists orderable models and features, as well as replacement parts for the 3581 Tape Autoloader. To order a part by feature code, contact your local IBM Marketing Representative or Business Partner. If the part has a customer replaceable unit (CRU) number, it is available through the IBM Technical Support Center. Note: Power cords are listed separately in Power Cords on page 218; media supplies are listed in Ordering Media Supplies on page 159.
| | | | | | | | | | | | | | | | | | | | | | | |
FC 7004 FC 3104 FC 1660 FC 7003 FC 5302 FC 9702 FC 5305 FC 5310 FC 5325 FC 5602 FC 9703 FC 5604 FC 5610 FC 5625 FC 5907 FC 5922 FC 5961 FC 6005 FC 6025 FC 6061
217
Table 36. Parts list for the 3581 Tape Autoloader (continued) Feature Code (FC) Description SCSI LVD/SE terminator SCSI HVD Differential terminator SCSI LVD wrap tool Fiber wrap tool SC/LC Fiber Cable Interposer VHDCI/HD68 SCSI interposer cable Cleaning Cartridge 5-Pack Ultrium 2 Data Cartridge Model LL28/L38/L3H L28/L38/L3H with HVD Converter Kit L28/L38/L3H F28/F38/F3H F28/F38/F3H L28/L38/L3H L28/L38/L3H, F28/F38/F3H L28/L38/L3H, F28/F38/F3H CRU Part Number 19P0874 19P0378 19P0481 11P3847
| | | | | | | |
Power Cords
To avoid electrical shock, a power cord with a grounded attachment plug has been provided. Use only properly grounded outlets. Table 37 lists the power cord part number, feature code, the country or region where the power cord can be used, and the plugs standard reference. The last column in the table contains an index number that you can match to a specific receptacle type in Figure 142 on page 221. All power cords use an appliance coupler that complies with the International Electrotechnical Commission (IEC) Standard 320, Sheet C13. If the power cord that you receive does not match your receptacle, contact your place of purchase. Power cords used in the United States and Canada are listed by Underwriters Laboratories (UL), are certified by the Canadian Standards Association (CSA), and comply with the plug standards of the National Electrical Manufacturers Association (NEMA). For other worldwide geographies, plug standards are listed in Table 37.
Country or Region
Aruba, Bahamas, Barbados, Bermuda, Bolivia, Brazil, Canada, Cayman Islands, Colombia, Costa Rica, Curacao, Dominican Republic, Ecuador, El Salvador, Guatemala, Guyana, Haiti, Honduras, Jamaica, Japan, Liberia, Mexico, Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Saudi Arabia, South Korea, Suriname, Taiwan, Trinidad Tobago, Venezuela, US
218
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 37. Power cord information (continued) Description, Feature Code (FC), and Part Number (PN) Chicago 1.8 m, 125 V FC 9986 PN 6952301 US/Canada 2.8 m, 250 V FC 9833 PN 1838574 NEMA 6-15P Aruba, Bahamas, Barbados, Bermuda, Bolivia, Brazil, Canada, Cayman Islands, Costa Rica, Curacao, Dominican Republic, Ecuador, El Salvador, Guatemala, Guyana, Haiti, Honduras, Jamaica, Japan, Liberia, Netherlands Antilles, Nicaragua, Panama, Peru, Philippines, Suriname, Taiwan, Thailand, Trinidad Tobago, Venezuela, US Argentina, Australia, China, Colombia, New Zealand, Papua New Guinea, Paraguay, Uruguay, Western Samoa 2 Plug Standard Reference NEMA 5-15P Index Number in Figure 142 on page 221 1
Country or Region
Chicago, U.S.A.
Australia 2.8 m, 250V FC 9831 PN 13F9940 France, Germany 2.8 m, 250V FC 9820 PN 13F9979
CEE 7 - VII
Afghanistan, Algeria, Andorra, Angola, Aruba, Austria, Belgium, Benin, Brazil, Bulgaria, Burkina Faso, Burundi, Cameroon, Central African Republic, Chad, Congo-Brazzaville, Curacao, Czech Republic, Democractic Republic of Congo, Denmark, Egypt, Finland, France, French Guiana, Germany, Greece, Guinea, Hungary, Iceland, Indonesia, Iran, Ivory Coast, Jordan, Kenya, Korea, Lebanon, Luxembourg, Macau, Malagasy, Mali, Martinique, Mauritania, Mauritius, Monaco, Morocco, Mozambique, Netherlands, Netherlands Antilles, New Caledonia, Niger, Norway, Poland, Portugal, Romania, Russia, Saudi Arabia, Senegal, Spain, Sweden, Sudan, Syria, Togo, Tunisia, Turkey, Yugoslavia, Zaire, Zimbabwe, Vietnam Denmark
Denmark 2.8 m, 250V FC 9821 PN 13F9997 South Africa 2.8 m, 250V FC 9829 PN 14F0015 United Kingdom 2.8 m, 250V FC 9825 PN 14F0033
DK2-5A
SABS 164
BS 1363
Antigua, Bahrain, Bermuda, Brunei, Channel Islands, China (Hong Kong S.A.R.), Cyprus, Fiji, Ghana, Guyana, India, Iraq, Ireland, Jordan, Kenya, Kuwait, Malaysia, Malawi, Malta, Nepal, Nigeria, Oman, Polynesia, Qatar, Sierra Leone, Singapore, Tanzania, Uganda, UK, United Arab Emirate (Dubai), Yemen, Zambia
219
Table 37. Power cord information (continued) Description, Feature Code (FC), and Part Number (PN) Switzerland 2.8 m, 250V FC 9828 PN 14F0051 Italy 2.8 m, 250V FC 9830 PN 14F0069 Israel 2.8 m, 250V FC 9827 PN 14F0087 Argentina 2.8 m, 250V FC 9834 PN 36L8880 China 2.8 m, 250V FC 9840 PN 02K0546 Note: Part number 6952300 is the default power cord for the countries or regions listed. If you do not specify a power cord when you place your order, IBM provides this power cord. CCEE Peoples Republic of China 12 IEC 83-A5 Argentina, Brazil, Colombia, Paraguay, Trinidad Tobago, Uruguay 11 S11-32-1971 Israel 10 CEI 23- 16 Chile, Ethiopia, Italy, Libya, Somalia 9 Plug Standard Reference SEV SN 416534 Index Number in Figure 142 on page 221 8
Country or Region
Liechtenstein, Switzerland
Types of Plugs
Figure 142 on page 221 shows the plugs that are used by the power cords in Table 37 on page 218. Match the index number that is beside each plug to the index number in the table.
220
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
10
11
12
x26416
221
222
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Part 4. Appendixes
223
224
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Element Addresses
Elements are the locations in the Autoloader that can accept a cartridge. The Autoloader includes three types of elements: v Medium transport element: The cartridge loader and carousel make up the medium transport element. The carousel positions the specified cartridge in front of the tape drive and the cartridge loader moves the cartridge between the tape drive and the storage slot. v Storage elements: The eight cartridge slots in the Autoloader are storage elements. v Data transfer element. The tape drive is a data transfer element that reads and writes data as requested by the host. The Autoloader maintains current information about each element in its cartridge inventory, which is stored in memory. Each of the elements in the Autoloader requires an address so it can be identified by SCSI commands. Figure 143 on page 226 shows the default address assigned to each element in the Autoloader. In addition to element addresses, each of the cartridge slots is assigned an element index. The element indexes are identical to the default element addresses. Unlike the element addresses, the element indexes are permanently coded in the Autoloaders firmware and cannot be changed. The OCPs LCD displays the element indexes, not the element addresses for the cartridge slots. The slot numbers are displayed in hexadecimal format (1h through 8h). Use the MODE SELECT command to change the address of each element in the Autoloader.
225
|
3
9 7 10
a67s0272
| | | | | | | | | | | | | | | | | |
Figure 143. Default Element Addresses and Element Indexes Element Description 1 2 3 4 5 6 7 8 9 10 Cartridge Slot 1 Cartridge Slot 2 Cartridge Slot 3 Cartridge Slot 4 Cartridge Slot 5 Cartridge Slot 6 Cartridge Slot 7 Cartridge Slot 8 Cartridge Loader/Carousel Tape Drive Element Address (hex) 1 (1h) 2 (2h) 3 (3h) 4 (4h) 5 (5h) 6 (6h) 7 (7h) 8 (8h) 82 (52h) 86 (56h) Element Indexes 1 2 3 4 5 6 7 8 -
226
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
TapeAlert Flags
The Autoloaders internal TapeAlert firmware constantly monitors the Autoloaders operation for problems. TapeAlert is an industry-standardized method for reporting errors and potential difficulties to the software application.
Description The library mechanism is having difficulty communicating with the drive: v Turn the library OFF than ON v Restart the operation If the problem persists, contact Technical Support
02
There is a problem with the media changer mechanism. If the problem persists, contact Technical Support. The media changer has a hardware fault: v Make sure the media changer and drives are not being used by any host, then reset the media changer from the front panel. v If the problem persists, contact Technical Support.
03
04
Autoloader Hardware D
v Make sure the media changer and drives are not being used by any host, then reset the media changer from the front panel. v If the problem persists, contact Technical Support. There is a potential problem with the cartridge loader picking a cartridge from a drive or slot. v No action needs to be taken at this time. v If the problem persists, contact Technical Support. This flag is cleared when the next move command is received.
13
14
There is a potential problem with the cartridge loader placing a cartridge into a slot. v No action needs to be taken at this time. v If the problem persists, contact Technical Support. This flag is cleared when the next move command is received.
227
Table 38. TapeAlert Flags supported by the Autoloader (continued) Parameter Code 15 Flag Name Drive Load Retry Type W
a
Description There is a potential problem with the cartridge loader or drive when placing a cartridge into a drive. v No action needs to be taken at this time. v If the problem persists, contact Technical Support. This flag is cleared when the next move command is received.
16
Autoloader Door
The operation has failed because the Autoloader door is open. v Clear any obstructions from the media changer door. v Close the Autoloader door. v If the problem persists, contact Technical Support. This flag is cleared when the door is closed.
19 24
W C
Autoloader security has been compromised. The door was opened then closed during operation. The library has detected an inconsistency in its inventory. v Redo the library inventory to correct inconsistency v Restart the operation Check the applications users manual or the hardware users manual for specific instructions on redoing the library inventory.
27 32
W I
One or more fans inside the Autoloader have failed. This flag is cleared when all fans are working again. The Autoloader was unable to read the bar code on a cartridge
v I = Informational suggestion to user. v W = Warning. Remedial action is advised. Performance of data may be at risk. v C = Critical. Immediate remedial action is required.
228
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Media
Set for any unrecoverable read, Replace the tape cartridge. write, or positioning error that is due to a faulty tape cartridge. Set for any unrecoverable read error where isolation is uncertain and failure could be due to a faulty tape cartridge or to faulty drive hardware. Set for any unrecoverable write or positioning error where isolation is uncertain and failure could be due to a faulty tape cartridge or to faulty drive hardware. If Flag 4 is also set, the cartridge is defective. Replace the tape cartridge. If Flag 4 is not set, see Troubleshooting on page 163. If Flag 9 is also set, make sure that the write-protect switch is set so that data can be written to the tape (see Setting the Write-Protect Switch on page 147). If Flag 4 is also set, the cartridge is defective. Replace the tape cartridge. If Flag 4 is not set, see Troubleshooting on page 163. Replace the tape cartridge. If this error occurs with multiple cartridges, see error code 6 in Table 35 on page 179. Make sure that the cartridges write-protect switch is set so that the tape drive can write data to the tape (see Setting the Write-Protect Switch on page 147). Refer to the documentation for your servers operating system.
Read failure
Write failure
Set when severe servo errors occur while loading a tape cartridge.
Write protect
Set when the tape drive detects that the tape cartridge is write protected.
10
No removal
Set when the tape drive receives an UNLOAD command after the server prevented the tape cartridge from being removed. Set when you load a cleaning cartridge into the drive.
11 12
No action required.
Set when you load an unsupported Use a supported tape cartridge. cartridge type into the drive or when the cartridge format has been corrupted. Set when the tape split apart. Manually remove the tape cartridge (see Contacting IBM Technical Support on page 200).
14
15
Set when a cartridge memory (CM) Replace the cartridge. If this error failure is detected on the loaded tape occurs on multiple tapes, see error cartridge. code 6 in Table 35 on page 179.
229
Table 39. TapeAlert flags supported by the drive (continued) TapeAlert Flags Supported Flag Number 16 Flag Forced eject Description Set when you manually unload the tape cartridge while the drive was reading or writing. Action Required No action required.
18
Tape directory corrupted Set when the drive detects that the in the cartridge memory tape directory in the cartridge memory has been corrupted. Clean now Clean periodic Set when the tape drive detects that it needs cleaning. Set when the drive detects that it needs routine cleaning.
Re-read data from the tape to rebuild the tape directory. Clean the tape drive. Clean the tape drive as soon as possible. The drive can continue to operate, but you should clean the drive soon. Replace the cleaning cartridge. Use a valid cleaning cartridge.
20 21
22 23
Set when the tape drive detects a cleaning cartridge that has expired. Set when the tape drive expects a cleaning cartridge and the loaded cartridge is not a cleaning cartridge. Set when a hardware failure occurs which requires that you reset the tape drive to recover.
30
Hardware A
If resetting the drive does not recover the error, note the error code on the single-character display and see Table 35 on page 179 for the appropriate instructions. Note the error code on the single-character display and see Table 35 on page 179 for the appropriate instructions. See error code 8 or 9 in Table 35 on page 179. Unload and reload the tape cartridge. Download the FMR image again (ensure that it is the correct image). See error code 1 in Table 35 on page 179.
31
Hardware B
Set when the tape drive fails its internal Power-On Self Test (POST).
32
Interface
Set when the tape drive detects a problem with the SCSI or RS-422 interface. Set when a failure occurs that requires you to unload the cartridge from the drive and discard it. Set when an FMR image is unsuccessfully downloaded to the tape drive over the SCSI interface. Set when the drives temperature sensor indicates that the drives temperature is exceeding the recommended temperature of the enclosure (see Table 7 on page 16). Set when the drive detects that the externally supplied voltages are approaching the specified voltage limits or are outside the voltage limits (see Table 5 on page 15). Set when the drive detects a failure that requires diagnostics to isolate the problem.
33
Eject media
34
Download fail
36
Drive temperature
37
Drive voltage
39
Diagnostics required
230
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 39. TapeAlert flags supported by the drive (continued) TapeAlert Flags Supported Flag Number 51 Flag Description Action Required If the problem continues after successive loads, replace the cartridge. If the problem persists, replace the drive.
Tape directory invalid at For the tape that was unloaded, set unload when the tape directory on the cartridge memory is corrupted. Tape system area write failure
52
Set when the tape that was unloaded 1. Copy the data to another tape could not write its system area (FID) cartridge. successfully. 2. Discard the old cartridge. Set when the tape system area could not be read successfully at loadtime. 1. Copy the data to another tape cartridge. 2. Discard the old cartridge.
53
231
232
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Messages
The Messages appendix gives information on obtaining Autoloader and drive error information from different IBM and non-IBM servers (hosts).
233
Date/Time: Wed Oct 11 11:42:17 Sequence Number: 25265 Machine ID: 000D090D4C00 Node ID: tsm Error Class: H Error Type: PERM Resource Name: smc0 Resource Class: tape Resource Type: 3581 Location: 40-60-00-1,1 VPD: Manufacturer................IBM Machine Type and Model......ULT3581-TA2 Serial Number...............1323858 Device Specific . (FW) .....2.20 (Firmware Level) Description TAPE DRIVE FAILURE Probable Causes TAPE DRIVE Failure Causes TAPE TAPE DRIVE Recommended Actions PERFORM PROBLEM DETERMINATION PROCEDURES Detail Data SENSE DATA 0C01 0000 A520 FF2A 8000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
Figure 144. AIX ERRPT Library Error Log Example Table 40. AIX ERRPT Library Sense Data Hex A5 0000, 0100, 0010 70 09 FF2A Description SCSI Command Command Parameters Byte 0 of Library Sense Data Sense Key ASC/ASCQ (Additional Sense Code/Additional Sense Code Qualifier)
234
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Date/Time: Wed Oct 10 11:39:43 Sequence Number: 25264 Machine ID: 000D090D4C00 Node ID: tsm Class: H Type: PERM Resource Name: rmt2 Resource Class: tape Resource Type: LTO Location: 40-60-00-1,0 VPD: Manufacturer................IBM Machine Type and Model......ULT3581-TD2 Serial Number...............1300015078 Device Specific.(FW)........35N0 (Firmware Level) Description TAPE OPERATION ERROR Probable Causes TAPE User Causes MEDIA DEFECTIVE DIRTY READ/WRITE HEAD Recommended Actions FOR REMOVABLE MEDIA, CHANGE MEDIA AND RETRY PERFORM PROBLEM DETERMINATION PROCEDURES Detail Data SENSE DATA 0602 0000 0100 5200 0700 20B0 0000 0000 0000 0000 0000 0000 0000 0000 0000
Figure 145. AIX ERRPT Drive Error Log Example Table 41. AIX ERRPT Drive Sense Data Hex 01 0000, 0200, 0000 70 03 5200 20B0 058A 02 Description SCSI Command Command Parameters Byte 0 of Tape Drive Sense Data Sense key (Hardware error in this example) ASC/ASCQ (Additional Sense Code/Additional Sense Code Qualifier) FSC (Fault Symptom Code) Relative LPOS SCSI ID
Appendix D: Messages
235
Summary Report
1 FFE2F73A 0BA49C99 C60BB505 C42F11D4 C42F11D4 FFFA352B FFFA352B 5537AC5F 5537AC5F 5537AC5F 5537AC5F 5537AC5F 5537AC5F C60BB505 C42F11D4 C42F11D4 C42F11D4 C42F11D4 FFFA352B FFFA352B C42F11D4 C42F11D4 C42F11D4 C42F11D4 2 3 4 5 1012150900 U H rmt5 1012150800 T H scsi8 1012141500 P S 1012105200 U S VSC:DE 1012105000 U S VSC:DE 1012104900 U S MS:CS 1012104900 U S MS:CS 1012091700 1012091700 1012091700 1012091600 1012091600 1012091600 1012082000 1011183600 1011183300 1011181800 1011174700 1011172900 1011172900 1011155300 1011153900 1011153800 1011150900 P P P P P P P U U U U U U U U U U H H H H H H S S S S S S S S S S S rmt9 rmt9 rmt9 rmt8 rmt8 rmt8 VSC:DE VSC:DE VSC:DE VSC:DE MS:CS MS:CS VSC:DE VSC:DE VSC:DE VSC:DE 6 UNDETERMINED ERROR SCSI BUS ERROR 7 SOFTWARE PROGRAM ABNORM TERMINATED SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR TAPE DRIVE FAILURE TAPE DRIVE FAILURE TAPE DRIVE FAILURE TAPE DRIVE FAILURE TAPE DRIVE FAILURE TAPE DRIVE FAILURE SOFTWARE PROGRAM ABNORM TERMINATED SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR SOFTWARE ERROR
236
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
2) Reference codes. . . . . . . . . . . . . *ALL d. Device selection 1) Option . . . . . . . . . . . . . . . . . . . 1 2) Device type or resource names . . *ALL 7. On the Log Analysis Report screen, enter a 5 on an error line that has a resource type of 3581 (autoloader) or 3580 (drive), and press [Enter]. 8. On the Display Detail Report for Resource screen, press: v F4=Additional Information. Pressing F4 will display the machine type and serial number of the device. It also will display SCSI sense data, if available. v F6=Hexadecimal report. Pressing F6 will display the device hexadecimal data (for support use). v F9=Address Information. Pressing F9 will display the SCSI address information.
Appendix D: Messages
237
238
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
There is an older version of the syslog.log file called OLDsyslog.log. The file that is required is the one that was recording information at the time of the problem. In addition, you may use error logs from the application (such as Tivoli Storage Manager), or the Device Error Log for problem determination.
Fixing Drive SCSI Bus Errors Fixing a Consistent Error with a Single Drive on a SCSI Bus
1. Ensure that the Autoloader is powered on. 2. Ensure that the tape drives SCSI address is the same as the SCSI address assigned by the server. 3. See Diagnostic Menu on page 67 and select the Wrap test. v If the test runs successfully, replace the SCSI cable and the interposer (if installed). Repeat the operation that caused the error. If you replaced the SCSI cable and the problem persists, the fault is with the servers hardware or software. To isolate the cause of the failure, refer to the servers service documentation. v If the test fails, rerun the SCSI wrap test with a new SCSI terminator. v If the test fails again, replace the Autoloader (see Removing/Replacing the Autoloader on page 204). 4. See SCSI / FIBRE WRAP TEST on page 72 and run the wrap test. v If the test fails, re-run the wrap test with a new SCSI terminator. If the test fails again, replace the Autoloader (see Removing/Replacing the Autoloader on page 204). v If the test runs successfully, use the ITDT tool to run the test device diagnostic. If the test device diagnostic fails, there is a problem between the Autoloader and the host. Check the SCSI connectors for bent pins. If the cables are okay, the problem may be with the servers hardware or software. Refer to the servers service documentation. If the test device diagnostic runs successfully, and the original problem persists, the failure is outside the Autoloader and its attachments. Use the
Appendix D: Messages
239
server or host service documentation, as appropriate. Also, ensure that the device drivers are at the latest level. (See Step 3. Install Device Drivers on page 110.)
| | | |
Attention At the time of publication, the ITDT tool was not available. Register with MySupport (http://www.ibm.com/support/mySupport) to be notified by email when the tool becomes available, or periodically check the IBM support site (http://www.ibm.com/storage/lto).
240
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Sense Data
The Sense Data appendix contains Autoloader and drive sense data and information on using host sense data.
2h 4h 5h
6h Bh
Possible Additional Sense Codes (ASC) and Additional Sense Code Qualifiers (ASCQ).
Table 43. Autoloader possible Additional Sense Codes (ASC) and Additional Sense Code Qualifiers (ASCQ) Sense Key No Sense (00) Recovered Error (01) Not Ready (02) 0Ah 47h 04h 04h 04h 04h 04h 04h 00h 00h 00h 01h 03h 07h 83h 85h 8Dh 8Eh 01h ASC ASCQ No Sense Error log overflow SCSI parity error Cause not reportable Becoming ready, scanning magazines, etc. Not ready, manual intervention required Not ready, other command in progress Not ready, door open Not ready, firmware upgrade in progress Not ready, the media charger is offline Not ready, the media charger is in sequential mode Unit not ready, Inventory not valid Message
| |
241
Table 43. Autoloader possible Additional Sense Codes (ASC) and Additional Sense Code Qualifiers (ASCQ) (continued) Sense Key Hardware Error (04) ASC 3Ah 40h 44h 44h 44h 44h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h ASCQ 80h 84h 80h 81h 86h FFh 70h 73h 74h 75h 76h 77h 78h 79h 7Ah 7Bh 7Ch 7Dh 7Eh 7Fh 87h 88h 89h 90h 91h 92h Media not present POST soft failure Loader communications timeout Loader communication UART error or buffer overflow Bad status returned from the Autoloader Unexpected status from test Cartridge has no home No cartridge in drive during unload Loader mechanism problem, after retries Time out moving cartridge Reserved Couldnt unlock door after retries Error during SCAN MAGAZINE Couldnt unlock door after retries Unexpected door open Didnt find all expected slots during elevator movement Cartridge already in drive during LOAD CARTRIDGE Slot empty during LOAD CARTRIDGE Cleaning tape expired Cleaning failed Hardware Error Global Timeout Hardware Error Communication error Hardware Error Timeout during BHC testing Mechanical Positioning Error Scan Failure Preposition Failed Message
242
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 43. Autoloader possible Additional Sense Codes (ASC) and Additional Sense Code Qualifiers (ASCQ) (continued) Sense Key Hardware Error (04) [continued] ASC 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h ASCQ 93h 94h 95h 96h A0h A1h A2h A3h A4h A5h B0h B1h B2h B3h B4h B5h B6h B7h BAh BBh BCh BDh BEh BFh Message Cartridge load error Cartridge failed to unload Import Error Export Error Belt Axis Error Slider Axis Error Gripper Position Error Cartridge Pick Error Door Function Error Hardware Error Fan Error ROM Error RAM Error Hardware Error NVRAM Error Hardware Error CTC Error Hardware Error UART Error Hardware Error DISPLAY Error Hardware Error Memory Error Hardware Error Timeout Loader Command Hardware Error Drive load timeout Hardware Error Drive unload timeout Hardware Error Over temperature problem Hardware Error No Connection to Drive Hardware Error Genetic Drive Response error Hardware Error Drive broken: Needs repair
Appendix E: Sense
243
Table 43. Autoloader possible Additional Sense Codes (ASC) and Additional Sense Code Qualifiers (ASCQ) (continued) Sense Key Illegal Request (05h) ASC 1Ah 20h 21h 24h 24h 24h 24h 24h 24h 24h 24h 24h 24h 24h ASCQ 00h 00h 01h 00h 81h 82h 83h 86h 87h 88h 89h 8Ah 8Fh 90h 91h 00h 00h 01h 02h 00h 0Dh 0Eh 00h 00h 01h 00h 02h 00h 00h 05h 06h 01h 01h 00h 00h 00h Message Parameter length error SCSI invalid opcode Invalid element address Invalid field CDB Invalid mode on WRITE BUFFER Invalid drive specified SEND DIAG Invalid test number Invalid offset on WRITE BUFFER Invalid size on WRITE BUFFER Wrong sequence number of code image Wrong checksum of code image Wrong header length of code image Bad controller image checksum Wrong flash file (image does not fit to boot code) Wrong firmware image, personality mismatch Invalid LUN Invalid field in parameter list Parameter list error: parameter not supported Parameter value invalid Saving parameters not supported Destination element full Source slot or drive empty SCSI invalid ID message Media Load/Eject failure Cartridge failed to unload Command unspecified Unrecognized Autoloader command Not ready to ready transition/Door was open and closed again. Power on reset occurred Bus type changed to Single Ended (SE) Bus type changed to Low Voltage Differential (LVD) Mode parameters changed Microcode has changed SCSI message error SCSI parity error SCSI invalid message
24h 25h 26h 26h 26h 39h 3Bh 3Bh 3Dh 53h 53h F1h F1h Unit Attention (06h) 28h 29h 29h 29h 2Ah 3Fh Command Aborted (0Bh) 43h 47h 49h
244
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
1 2
3 4 5 6 7 811
Information byte (most significant byte) Information byte Information byte Information byte (least significant byte) Additional Sense Length Command specific information
Appendix E: Sense
245
Table 44. LTO Tape Drive Sense Data (continued) Bit Address or Name Byte 1213 7 6 5 4 3 2 1 0
Additional Sense Code (ASC) Additional Sense Code Qualifier (ASCQ) Byte 12 Byte 13 ASC ASCQ 00 00 - No additional sense The flags in the sense data indicate the reason for the command failure 00 01 - Filemark detected A Read or Space command terminated early due to an FM The FM flag is set. 00 02 - EOM A Write or Write File Marks command failed because the physical end of tape was encountered, or a Read or Space command encountered EOM The EOM flag is set 00 04 - BOM A space command ended at Beginning of Tape The EOM bit is also set 00 05 - EOD Read or Space command terminated early because End of Data was encountered 04 00 - Cause not reportable A cartridge is present in the drive, but it is in the process of being unloaded 04 01 - Becoming Ready A media access command was received during a front panel initiated load or an immediate reported load command 04 02 - Initializing Command Required A cartridge is present in the drive, but is not logically loaded. A Load command is required 04 03 - Manual Intervention Required A cartridge is present in the drive but could not be loaded or unloaded without manual intervention 0C 00 - Write Error A Write operation has failed. This is probably due to bad media, but may be hardware related 11 00 - Unrecovered Read Error A Read operation failed. This is probably due to bad media, but may be hardware related 14 00 - Recorded Entity Not Found A space or Locate command failed because a format violation prevented the target from being found. 14 03 - End Of Data not found A Read type operation failed because a format violation related to a missing EOD data set 1A 00 - Parameter list length error The amount of parameter data sent is incorrect 20 00 - Invalid Command Operation Code The Operation Code in the command was not a valid Operation Code 24 00 - Invalid field in CDB An invalid field has been detected in a Command Descriptor Block 25 00 - LUN not supported The command was addressed to a non-existent logical unit number 26 00 - Invalid Field in Parameter List An invalid field has been detected in the data sent during the data phase 27 00 - Write Protect A Write type operation has been requested on a cartridge which has been write protected 28 00 - Not Ready to Ready Transition A cartridge has been loaded successfully into the drive and is now ready to be accessed 29 00 - Reset The drive has powered on, received a reset signal or a bus device reset signal since the initiator last accessed it 2A 01 - Mode Parameters Changed The Mode parameters for the drive have been changed by an initiator other than the one issuing the command 30 00 - Incompatible Media Installed A write type operation could not be executed because it is not supported on the cartridge type that is loaded. 30 01 - Unknown Format An operation could not be carried out because the cartridge in the drive is of a format not supported by the drive (Continued on next page)
246
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 44. LTO Tape Drive Sense Data (continued) Bit Address or Name Byte 1213 7 6 5 4 3 2 1 0
Additional Sense Code (ASC) Additional Sense Code Qualifier (ASCQ) (Continued) Byte 12 Byte 13 ASC ASCQ 30 02 - Incompatible Format An operation could not be completed because the Logical Format is not correct 30 03 - Cleaning Cartridge Installed An operation could not be carried out because the cartridge in the drive is a cleaning cartridge 30 07 - Cleaning Failure A cleaning operation was attempted, but could not be completed for some reason 31 00 - Media format corrupted Data could not be read because the format on tape is not valid, but is a known format. A failure occurred attempting to write the FID 37 00 - Rounded parameter A Mode Select command parameter has been rounded because the drive can not store it with the accuracy of the command. 3A 00 - Media Not Present A media access command has been received when there is no cartridge loaded 3B 00 - Sequential Positioning Error A command has failed and left the logical position at an unexpected location 3D 00 - Invalid bits in identify Message An illegal Identify Message has been received at the drive at the start of a command 3E 00 - Logical Unit has not Self-Configured The drive has just powered on and has not completed its self test sequence and can not process commands 3F 01 - Code Download The firmware in the drive has just been changed by a Write Buffer command 40 xx - Diagnostic failure A diagnostic test has failed. The xx (ASCQ) is a vendor specific code indicating the failing component. 43 00 - Message Error A message could not be sent or received due to excessive transmission errors 44 00 - Internal target failure A hardware failure has been detected in the drive that has caused the command to fail 45 00 - Select/Reset Failure An attempt to reselect an initiator in order to complete the command has failed 4B 00 - Data Phase Error A command could not be completed because too many parity errors occurred during the Data phase 4E 00 - Overlapped Commands An initiator selected the drive even though it already had a command outstanding in the drive 50 00 - Write Append Error A write type command failed because the point at which to append data was unreadable 51 00 - Erase failure An Erase command failed to erase the required area on the media 52 00 - Cartridge fault A command could not be completed due to a fault in the tape cartridge 53 00 - Media Load/Eject Failed (Sense Key 03) An attempt to load or eject the cartridge failed due to a problem with the cartridge. 53 00 - Media Load/Eject Failed (Sense Key 04) An attempt to load or eject the cartridge failed due to a problem with the drive 53 02 - Media Removal Prevented An Unload command has failed to eject the cartridge because media removal has been prevented 5D 00 - Failure Prediction Threshold Failure Prediction thresholds have been exceeded indicating that a failure may occur soon 5D FF - Failure Prediction False A Mode Select command has been used to test for Failure Prediction system. 82 82 - Drive requires cleaning The drive has detected that a cleaning operation is required to maintain good operation 82 83 - Bad Code Detected The data transferred to the drive during a firmware upgrade is corrupt or incompatible with drive hardware
Appendix E: Sense
247
Table 44. LTO Tape Drive Sense Data (continued) Bit Address or Name Byte 14 15 7 FRU code SKSV C/D Reserved BPV When set to 1, the bit pointer is valid. 16 17 1819 20 21 2228 29 3033 34 35 Reserved SKSV = 0: First Error Fault Symptom Code (FSC). SKSV = 1: Field Pointer First Error Flag Data Reserved (0) CLN Volume Label Current Wrap Relative LPOS SCSI Address Reserved Reserved Reserved VolValid Bit pointer 6 5 4 3 2 1 0
The descriptions below serve only as an overview of sense reporting in the tape drive. This tape drive conforms to all sense field reporting as specified in the SCSI standards. Notes: 1. The Error Code field (Byte 0) is set to 70h to indicate a current error, that is one associated with the most recently received command. It is set to 71h to indicate a deferred error which is not associated with the current command. 2. The segment number (Byte 1) is zero since the Copy, Compare, and Copy and Verify commands are not supported. 3. The File Mark flag (Byte 2, bit 7) is set if a Space, Read, or Verify command did not complete because a file mark was read. 4. The End of Media (EOM) flag (Byte 2, bit 6) is set if a Write or Write File Marks command completed in the early warning area. Spacing into BOM also causes this flag to be set. It is also set on an attempt to read or space past EOD, or if an attempt is made to space into Beginning of Media. 5. The Illegal Length Indicator (ILI) flag (Byte 2, bit 5) is set if a Read or Verify ended because a block was read from tape that did not have the block length requested in the command. 6. The Information Bytes (Bytes 35) are only valid if the Valid flag is set. This occurs only for current errors and not for deferred errors. 7. The Field Replaceable Unit field (Byte 14) is set to either zero or to a non-zero, vendor-specific code indicating which part of the drive is suspected of causing the failure. 8. The Clean (CLN) flag (Byte 21, bit 3) is set if the drive needs cleaning and clear otherwise. 9. The Volume Label Fields Valid (VolValid) bit (Byte 21, bit 0) is set if the Volume Label being reported is valid.
248
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
10. The Volume Label field (Bytes 2228) reports the volume label if a cartridge is loaded in the drive and Volume Label Fields Valid is set. 11. The Current Wrap field (Byte 29) reports the physical wrap of the tape. The least significant bit reflects the current physical direction. A 0 means that the current direction is away from the physical beginning of the tape. A 1 means that the current direction is towards the physical beginning of the tape. 12. Relative LPOS fields (Bytes 3033) reports the current physical position on the tape. 13. SCSI Address field (Byte 34) reports the SCSI Bus Address for the drive. Values returned range from 00h to 0Fh.
| |
AIX
| | | | | |
Attention At the time of publication, the ITDT tool was not available. Register with MySupport (http://www.ibm.com/support/mySupport) to be notified by email when the tool becomes available, or periodically check the IBM support site (http://www.ibm.com/storage/lto).
HP Sun Microsystems
HP-UX Solaris
Uses the IBM device driver for HP. Error and trace logging are proprietary to Hewlett-Packard. Uses the IBM device driver for Solaris to post sense information to the Solaris host-wide messages file /var/adm/messages. Uses the NTUTIL device driver to log some sense data in the Event Viewer host log. Uses the IBM device driver for Linux to post sense information to the Linux files /var/log/IBMtape.errorlog and /var/log/IBMtape.trace.
Intel-based PCs
Appendix E: Sense
249
250
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | |
Operating Mode SCSI Drive Speed (Model L28/L38/L3H only) Fibre Channel Drive Speed (Model F28/F38/F3H only) Loop Port Type (Model F28/F38/F3H only) World Wide Node Name (Model F28/F38/F3H only) SCSI Inquiry String IP Address (for RMU) Network Mask (for RMU) Gateway Address (for RMU)
AUTO
80 Mb/s
| | |
AUTO
1Gb/s
2Gb/s
LN
NL
IBM ULT3581TL
251
| |
Administrator Passwords
OCP:
RMU:
Serial:
252
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
The Autoloader requires 2 EIAs (units) of rack space. The Rack Mount Template helps in identifying proper placement of the clip-nuts. Two types of clip-nuts are included with the Rack Mount Kit: v Panel clip-nuts (for racks with round mounting holes) are installed by sliding them on from the side of each rack rail with the largest part of the clip-nut going on the back side of the rack rail. v Cage clip-nuts (for racks with square mounting holes) are installed from the back side of each rack rail. To install the clip-nuts: 1. Identify the 2 EIAs needed on the rack rail. If your rack does not contain a rail with each EIA numbered, identify the two EIAs required by holding the template on the outside of the rack rail and aligning all six circles on the template with the holes in the rail. Note: All six circles on the template must align exactly with the holes of the 2 EIAs in the rack rail. 2. Install clip-nuts in the rail holes indicated by the filled circles on the template. v Top hole of the higher EIA v Top hole of the lower EIA v Bottom hole of the lower EIA 3. Count the holes in the other rack rails, up or down, to determine EIA location and install clip-nuts using the Rack Template.
a67s0246
253
254
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Gripper Calibration
After every power on and after the first cartridge is loaded into the drive, the gripper calibrates its movement to the drive.
Service Menus
Three Service Menus exist for the Autoloader: v LIBRARY SERVICE in the Diagnostics Menu accessed via the OCP. v ADVANCED DIAGNOSTICS in the Maintenance Menu accessed via the RMU, if installed. v Diagnostic and maintenance tests accessed via serial communication.
TEST STATUS
STOPPING TEST
> >
SLIDER TEST (INV. STATUS) TEST STATUS
X
STOPPING TEST
> >
GRIPPER TEST (INV. STATUS) TEST STATUS
X
STOPPING TEST
> >
DOOR TEST (INV. STATUS) TEST STATUS
X
STOPPING TEST
> >
SENSOR TEST (INV. STATUS) TEST STATUS
X
STOPPING TEST
> >
LOAD-UNLOAD (INV. STATUS) TEST STATUS
X
STOPPING TEST
> >
POSITION TEST (INV. STATUS) TEST STATUS
X
STOPPING TEST
> >
SET LOG MODE (INV. STATUS) TRACE MODE ON
> >
255
a67s0227
> >
Login
To login to LIBRARY SERVICE via the OCP: 1. Press Enter to access LOADER DIAGNOSTIC. | 2. Press Enter then press Next until LIBRARY SERVICE displays. 3. Press Enter to access the SERVICE PIN screen. 4. Use Next and Previous to enter each digit then press Enter to proceed to the next digit. 5. After entering the last digit and pressing Enter, SERVICE PIN PASSED or SERVICE PIN FAILED will display. v If FAILED, press Cancel and enter the password again. v If PASSED, press Enter to proceed to BELT TEST.
BELT TEST
The BELT TEST rotates the carousel belt to verify that it is functioning properly. To run the BELT TEST: 1. Navigate to the BELT TEST and press Enter to begin the test. Cycles will increment in the display. 2. Press Cancel to stop the test.
SLIDER TEST
The SLIDER TEST performs the slider operation to verify that it is functioning properly. To run the SLIDER TEST: 1. Navigate to the SLIDER TEST and press Enter to begin the test. 2. Press Cancel to stop the test and return to the Home Screen.
GRIPPER TEST
The GRIPPER TEST performs the gripper operation to verify that it is functioning properly. To run the GRIPPER TEST: 1. Navigate to the GRIPPER TEST and press Enter to begin the test. 2. Press Cancel to stop the test and return to the Home Screen.
DOOR TEST
The DOOR TEST opens and closes the door to verify that it is functioning properly. To run the DOOR TEST: 1. Navigate to the DOOR TEST and press Enter to begin the test. 2. Press Cancel to stop the test and return to the Home Screen.
SENSOR TEST
The SENSOR TEST verifies that all internal sensors are functioning properly. To run the SENSOR TEST: 1. Navigate to the SENSOR TEST and press Enter to begin the test. 2. Press Enter to begin the test. Characters on the second line of the display are as follows: v B: 0 means no cartridge present in slot positioned in front of the drive 1 means cartridge present in slot positioned in front of the drive
256
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
v S: 0 1 v G: 0 1 v D:
means slider in home position (middle of path) means slider in path means gripper in home position or open means gripper in closed position
LOAD-UNLOAD
LOAD-UNLOAD tests the cartridge loader mechanism. To run the LOAD-UNLOAD TEST: 1. Navigate to the LOAD-UNLOAD TEST and press Enter to begin the test. 2. Press Cancel to stop the test and return to the Home Screen.
POSITIONS TEST
The POSITIONS TEST verifies that the carousel is properly aligned. To run the POSITIONS TEST: 1. Navigate to the POSITIONS TEST and press Enter to begin the test. 2. Press Cancel to stop the test and return to the Home Screen.
CLEAR NVRAM
CLEAR NVRAM clears temporary information (such as error log data). To CLEAR NVRAM: 1. Navigate to CLEAR NVRAM and press Enter to access the ARE YOU SURE? screen. 2. Press Enter for YES. 3. Cycle Autoloader power when prompted.
257
This menu item displays the Advanced Diagnostic table and the Media Status table. This menu item is available only to Authorized IBM Service Personnel. The Advanced Diagnostic table contains the following: v Select one of the following diagnostic operations: Long Read/Write Test: Performs a load operation, a write/read test, and an unload operation. Head Test: Performs diagnostics on difficult head patterns and determines if the head is functioning properly. Media Test: Verifies whether a suspect tape cartridge and its magnetic media are acceptable. Short Read/Write Test: Performs a load operation, a write/read test, and an unload operation. Self Test: Performs a system diagnostic. SCSI Wrap Test: Checks the SCSI (Model L28/L38/L3H) or Fibre Channel (Model F28/F38/F3H) circuitry. Load-Unload Test: Tests the cartridge loader mechanism. Belt Test: Rotates the carousel belt to verify that it is functioning properly. Slider Test: Performs the slider operation to verify that it is functioning properly. Gripper Test: Performs the gripper operation to verify that it is functioning properly. Door Test: Opens and closes the I/O Door to verify that it is functioning properly. Sensor Test: Verifies that all internal sensors are functioning properly. Preposition Test: Verifies that the carousel is properly aligned. v Enter the number of cycles to run the operation. Click EXECUTE to begin the diagnostic. Click STOP to terminate the diagnostic.
| |
258
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Figure 150. Serial port pin-out Pin Number 1 2 3 4 5 6 7 8 9 Signal Name Carrier detect Receive data Transmit data Data terminal ready Signal ground Data set ready Request to send Clear to send Ring indicator Abbreviation CD RD TD DTR SG DSR RTS CTS RI Direction Relative to the Autoloader In In Out Out In Out In In
a67r0088
259
Using HyperTerminal
HyperTerminal is a serial communications software provided with all PCs with a Windows operating system. Note: Other applications similar to HyperTerminal exist. If you are using an application other than HyperTerminal, please refer to that applications documentation for instructions. To use HyperTerminal, follow these instructions: 1. On your Windows desktop, click Start > Programs >Accessories > Communications > HyperTerminal 2. On the Connection Description window: v Type in 3581. v Click OK.
260
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0237
3. On the Connect To window: v Select the COM port that the serial cable was plugged into on the rear of your server (host). v Click OK.
a67s0238
261
4. On the COMx Properties window: v Select the following port settings: Bits per second = 38400 Data bits = 8 Parity = None Stop Bit = 1 Flow control = None v Click OK.
5. Press Enter. If you see the following screen, all went well and you are able to use the Serial Monitor. If you see nothing like this or only scrambled characters, check your connection parameters.
262
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0239
6. At the TSMON> prompt, type help for the list of serial commands.
TSMON>help
Below is a list of the more commonly used serial commands: v Login (lgi): User login. v Logout (lgo): User logout. v LibraryFirmware (lfw): Library firmware upgrade by XMODEM download (Transfer->Send file). v DriveFirmware (dfw): Drive firmware upgrade by XMODEM download (Transfer->Send file). v DriveDump (ddmp): Get drive dump by XMODEM upload (Transfer->Receive file). v DumpAll (dpa): Dump all status and traces. To store in a file, use Transfer->Capture text using XMODEM. v ErrorDump (edp): Dump the Autoloader error log. To store in a file, use Transfer->Capture text using XMODEM. v TraceDump (tdp): Dump the Autoloader trace log. To store in a file, use Transfer->Capture text using XMODEM. v IPAddress (ipa): ipa IP,Mask,Gateway. 7. To access the administrator serial menu: a. Type lgi and press Enter.
TSMON>lgi
Note: Both the OCP and RMU must be online (logged out) before the serial port will allow login. 1) For the User ID, type admin (Administrator) or the new Adminstrator User ID set for the RMU.
TSMON>lgi User ID:admin
2) For the password, type secure (Administrator) or the new Administrator password set for the RMU.
TSMON>lgi User ID:admin Password:secure
3) Press Enter. 8. Enter any command at the TSMON> prompt and press Enter to initiate. 9. When the operation is complete, type lgo at the TSMON> prompt to logout.
TSMON>lgo
263
Full Carousel?
YES
NO
IMPORT STATUS
DOOR STATUS
DOOR STATUS
CART. INSERTED
IMPORT & LOAD STATUS
FMR Cartridge?
YES
NO
DOOR STATUS
DOOR STATUS
Figure 154. Configuration Menus DRIVE FW UPGRADE FROM FMR TAPE command
264
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0175
To access CODE UPDATE: 1. Navigate to the Configuration Menu (see Configuration Menu on page 60). 2. Press Enter then press Next three times on the OCP to access DRIVE FW UPGRADE FROM FMR TAPE. 3. If there are eight cartridges (all slots are full) in your Autoloader, press Cancel on the OCP to return to the Configuration Menu screen. If there are less than eight cartridges (all slots are not full) in your Autoloader, proceed to the next step. 4. When the I/O Door opens, insert the FMR tape. 5. When the code update is complete, remove the ejected FMR tape from the I/O Door. 6. Press Enter on the OCP to return to the Home Screen.
265
| | | | | |
Attention (For Ultrium 3 drives only) Before attempting to remove a tape from the Autoloader or drive, it is very important to preserve the active dump information in non-volatile storage in case the Autoloader has to be replaced. This dump information will be used by the Repair Center when they perform failure analysis on the returned drive. Perform PRESERVE DUMP (LTO-3 only) on page 74 before powering OFF the drive. The sections that follow give instructions on removing a cartridge slot and cartridge and replacing the cartridge slot.
266
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
__ Step 1. Power off the Autoloader. __ Step 2. Unplug the power cord from the electrical outlet and from the rear panel of the Autoloader. __ Step 3. Remove all cables and the external fan from the Autoloaders rear panel. __ Step 4. Using a T10 Torx wrench, remove screws from the sides and rear of the Autoloader and remove the top cover. __ Step 5. To make slot removal easier, rotate the slot to be removed to the nearest corner position in the Autoloader. a. Facing the front of the Autoloader, place your left hand on the left middle slot in the Autoloader. b. Place your right hand on the right middle slot. c. Gently rotate the carousel counterclockwise until the desired slot is in a corner position.
CAUTION: DO NOT ROTATE CAROUSEL CLOCKWISE AS THIS WILL DAMAGE THE AUTOLOADER.
__ Step 6. Grasp the sides of a cartridge slot. __ Step 7. Gently lift the left side of the cartridge slot until the right track pin is removed from the track nearest the belt.
267
a67s0211
Figure 156. Top view of Autoloader with top cover removed showing cartridge slot being removed
__ Step 8. With the left side of the slot higher than the right side, turn the cartridge slot to the left while gently pulling up until the belt pin is free of the belt loop. __ Step 9. If necessary, push down on the belt near the belt pin with your free hand. __ Step 10. When the cartridge slot is removed from the Autoloader, lift the cartridge release lever on the right side of the cartridge slot and remove the cartridge. __ Step 11. Repeat Steps 5 through 10 for all remaining cartridge slots containing cartridges.
268
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0209
__ Step 2. Rotate the cartridge slot right until the left track pin is seated in the track nearest the belt. __ Step 3. Replace the top cover and secure with screws. __ Step 4. Replace the external fan.
269
a67s0210
| | | | | |
Attention (For Ultrium 3 drives only) Before attempting to remove a tape from the Autoloader or drive, it is very important to preserve the active dump information in non-volatile storage in case the Autoloader has to be replaced. This dump information will be used by the Repair Center when they perform failure analysis on the returned drive. Perform PRESERVE DUMP (LTO-3 only) on page 74 before powering OFF the drive.
Attention Perform this procedure only after you have attempted to remove the tape cartridge by power cycling the Autoloader. Note that (depending on its location on the reel) the tape may take as much as 20 minutes to completely rewind and eject. If a tape cartridge fails to eject from the Autoloader, you can manually remove the cartridge. The procedure to do so, however, requires care. Success depends on your ability to maintain constant and appropriate tension on the tape while rewinding it into the cartridge and disengaging it from the drives leader block. Apply too much tension and the tape may break; apply too little tension and the leader pin may fall from the leader block. IBM recommends that you read the complete instructions before starting the task, then perform the steps slowly and carefully to avoid complications.
Required Tools
| The following tools are required to manually remove a tape cartridge: v T10 Torx or small, flat-blade screwdriver v #1 Phillips screwdriver v 2.5-mm allen wrench v Small-blade screwdriver or potentiometer screwdriver v Needle-nose pliers v Flashlight (optional)
| | | | | | | | | | | |
270
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | | | | | | | | | | | | | | | |
a. Unplug the Autoloaders power cord from the electrical outlet and from the rear of the Autoloader. b. Remove any SCSI cable or SCSI terminator from the LVD SCSI connectors (connections on the SCSI connectors will interfere with the fan housing as it swings out to remove the captured tabs). c. Remove the RMU cable, if installed. 3. Remove the fan from the rear panel of the Autoloader. a. Loosen the two captured thumbscrews that fasten the fan housing to the Autoloader chassis. b. Pull gently on the right side (side containing the thumbscrews) of the fan housing until the power connector pulls free of the receptacle and the fan housing is rotated until it is perpendicular with the Autoloader rear panel. c. Pull the fan housing straight back, removing the tabs from the openings on the Autoloaders rear panel. 4. Remove the bottom cover of the Autoloader. a. Turn the Autoloader over so that the bottom is facing up and the unit is resting on the top cover. b. Remove the three screws from the rear panel ( 1 in Figure 158).
1
271
a67s0213
| | | |
c. Remove the 12 screws from the bottom cover ( 1 in Figure 159). d. Remove the 2 screws attaching the bottom cover to the sides of the Autoloader ( 2 in Figure 158 on page 271).
1 2
| |
272
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0277
| | |
5. Remove the drive from the Autoloader. a. Remove the four screws securing the drive ( 4 in Figure 160).
| | | | | | | | | | | | | | | | | | | | | |
b. Unplug the SCSI cable ( 5 in Figure 160). c. Unplug the power cable ( 2 in Figure 160). d. Unplug the RS-422 cable ( 3 in Figure 160). Use a flat blade screw driver to separate the two parts of the connector. e. The ribbon cable ( 1 in Figure 161 on page 275) is secured to the top of the drive by adhesive. Loosen the ribbon cable from the top of the drive, then carefully slide the drive from underneath the ribbon cable and out of the chassis.
273
| | | | | | | | | | | | | | | | | | | | |
b. Remove the fiber cable from the connectors. c. Remove the RMU cable, if installed. 3. Remove the fan from the rear panel of the Autoloader. a. Loosen the two captured thumbscrews that fasten the fan housing to the Autoloader chassis. b. Pull gently on the right side (side containing the thumbscrews) of the fan housing until the power connector pulls free of the receptacle and the fan housing is rotated until it is perpendicular with the Autoloader rear panel. c. Pull the fan housing straight back, removing the tabs from the openings on the Autoloaders rear panel. 4. Remove the bottom cover of the Autoloader. a. Turn the Autoloader over so that the bottom is facing up and the unit is resting on the top cover. b. Remove the three screws from the rear panel (refer to 1 in Figure 161 on page 275). c. Remove the 12 screws from the bottom cover (refer to 1 in Figure 159 on page 272). d. Remove the 2 screws attaching the bottom cover to the sides of the Autoloader (refer to 2 in Figure 161 on page 275). e. Lift the bottom cover off of the unit.
274
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
| | | | |
5. Remove the drive from the Autoloader. a. Lift the clear tab, squeeze the top and bottom of the cable plug to disengage the plug prongs (located on the underside of the plug) while pulling the fiber cable ( 5 in Figure 161) out of the connector on the back of the drive.
| | | | | | |
b. Unplug the power cable ( 2 in Figure 161). c. Unplug the RS-422 cable ( 3 in Figure 161). Use a flat blade screw driver to separate the two parts of the connector. d. Remove the four screws securing the drive ( 4 in Figure 161). e. The ribbon cable ( 1 in Figure 161) is secured to the top of the drive by adhesive. Loosen the ribbon cable from the top of the drive, then carefully slide the drive from underneath the ribbon cable and out of the chassis.
275
a67s0324
276
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0059
the leader pin was wedged in the clip area, grasp the leader pin with needle-nose pliers to free it and drop it into the cartridge.
Figure 163. Rewinding the leader pin into the tape cartridge
277
3 4 5
4 6 5
Figure 164. Guiding the leader pin into the tape cartridge
2. To prevent the leader pin block from jamming, press down on the linkage of the leader pin block 4 to force the hinged section of the block upward. 3. While manually rotating the loader motor gear in the unload direction, guide the end of the leader pin block 5 into the white block guide 6 . 4. Continue to rotate the loader motor gear counterclockwise until you feel resistance and the cartridge ejects. 5. Remove the tape cartridge. 6. To reuse the Autoloader, you must raise the drives loader so that it is able to accept a cartridge. To raise the loader, continue to wind the loader motor gear counterclockwise with the screwdriver until you feel resistance. 7. Remove the small-blade screwdriver. 8. If you choose to replace the Autoloader, return it in its original packaging or in the packaging from its replacement. 9. To reassemble the Autoloader, reverse the preceding steps. After you remove the stuck tape cartridge, copy the data on the tape to another tape. Then, discard the stuck tape cartridge.
278
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a67s0125
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
Attention v Before using this procedure, you must have exhausted all other means of removing the tape cartridge from the drive. Use this procedure only if you cannot remove the tape cartridge by using any other means. v Determine from the customer if the cartridge contains critical customer data. If the cartridge contains sensitive data that cannot leave the site, inform the customer that certain failure conditions diagnostics will be performed to test the drive for continued use. v The following removal procedures can destroy customer data! Use extreme care when handling or removing the customers tape cartridges to minimize tape damage and lost data. v DO NOT TOUCH the magnetic tape or tape path. Both are extremely sensitive to the oil and salt from your skin. Use clean, lint-free gloves when working around magnetic tape or the tape path components. v Electrostatic-sensitive components: Consider using an ESD Kit. v After you remove the tape cartridge, advise the customer to copy the data to another cartridge and to remove this tape cartridge from service. v Do not use power tools or magnetic tools to perform this procedure. v To avoid contamination and electrostatic-discharge damage to the drive, never touch the head or electronic components inside the drive. v If you cannot remove the cartridge from the drive using the following procedures, contact your next level of support.
Recommended Tools
v v v v v 2.5 mm offset hex wrench (do not use magnetized wrench) #1 Phillips screwdriver ESD Kit Flashlight (optional) #1 Flathead screwdriver (optional)
279
| | | | | | | | | | | | |
Beginning Procedure
__ 1. __ 2. __ 3. __ 4. Refer to the enclosure documentation for instructions on removing the drive. Place the drive on a non-slip, sturdy work surface. Ground yourself to the drive by using an ESD Kit. Remove the cover of the drive by performing the following steps: a. Using a Phillips screwdriver, remove the three screws and washers (see 1 in Figure 165) that secure the bezel 2 to the internal drive, then remove the bezel. b. Remove the cover of the internal drive by performing the following steps: 1) Remove the four cover-mounting screws and washers 3 . 2) Remove the cover by lifting it up.
1 3
3
Figure 165. Removing the cover from the internal drive
280
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a82ru007
| | | | | | | | | | | | | | | | | | | | | | | | | | | | |
__ 5. Inspect the drive to decide which of the following conditions most closely matches the symptom on the drive: v Tape spooled off the supply reel - All the tape appears to be on the take up reel and no tape is on the supply reel (inside the cartridge). Test the drive after the procedure is completed. v Tape pulled from leader pin (or broken at the front end) - All the tape appears to be on the supply reel (inside the cartridge) and very little or no tape appears to be on the take up reel. The leader block is positioned in the take up reel. Return the drive after the procedure is completed. v Tape broken in mid-tape - Tape appears to be on both the supply reel (inside the cartridge) and take up reel. Test the drive after the procedure is completed. v Tape tangled along tape path - Tape appears to be tangled and damaged but in tact. Return the drive after the procedure is completed. -- OR -No damage to tape (or no apparent failure) - There appears to be no damage or slack to the tape. Return the drive after the procedure is completed.
281
| | | | | | | | | |
__ 6. Turn the supply reel clockwise, allowing the moistened tape to adhere to the hub as it winds around the supply reel (inside the cartridge). __ 7. Continue spooling into the cartridge until the tape is taut and remains within the flanges of the tape guiding rollers. Ensure that you do not stretch the tape. __ 8. Reassemble the drive, reversing the steps in Beginning Procedure on page 280. __ 9. Allow the drive to perform mid-tape recovery. This takes several minutes. When this activity completes, the cartridge ejects automatically. __ 10. Test the drive to determine if it should be replaced.
282
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a82ru008
| |
| | | | | | | | | | | | | | | | | | | | | |
1 2 3 4 5
Loader motor worm gear Cartridge loader tray guide bearing Rotator stub Threader motor worm gear Threader intermediate gear
6 7 8 9
Threader mechanism gear Lever Loader mechanism gear Threader worm gear
__ 1. From the left side of the drive, pull out tape from the take up reel. Note: If there is more than approximately 0.6 m (2 ft.) of tape on the take up reel, go to Tape Broken in Mid-tape on page 285. __ 2. If there is less than approximately 0.6 m (2 ft.) of tape on the take up reel, cut off the excess tape as close to the leader pin, as possible. __ 3. Locate the threader motor worm gear ( 4 in Figure 167) the rear of the drive. You can either: a. Use your finger to rotate the threader motor worm gear and slowly rotate the threader mechanism gear ( 6 in Figure 167) clockwise; or b. Use a #1 flathead screwdriver to turn the threader worm gear ( 9 in Figure 167) clockwise. This rotates the threader motor worm gear ( 4 in Figure 167) clockwise, drawing the tape leader block assembly (LBA) into the cartridge.
283
a82ru009
| | | | | | | | | | | | | | | | | | | | | | | |
__ 4. As the LBA is secured in the cartridge, you should hear the LBA retention spring clips click into place. If you do not hear the click, continue rolling until the threader motor worm gear ( 4 in Figure 167 on page 283) stops. The LBA is in the correct position. Note: Be sure to keep tension on the tape as the LBA is drawn into the cartridge by using a hex wrench. __ 5. Notice the following: a. Loader mechanism gear ( 8 in Figure 167 on page 283) nearest the front of the drive that actuates the cartridge loader mechanism b. Position of the rotator stub ( 3 in Figure 167 on page 283). c. Front loader motor worm gear ( 1 in Figure 167 on page 283). Rotating this gear allows the loader mechanism gear ( 8 in Figure 167 on page 283) to turn. __ 6. Rotate the loader motor worm gear ( 1 in Figure 167 on page 283) to turn the loader mechanism gear ( 8 in Figure 167 on page 283) counterclockwise. Continue turning until the rotator stub ( 3 in Figure 167 on page 283) loses contact with the lever ( 7 in Figure 167 on page 283). This releases the LBA leader pin. __ 7. Rotate the threader motor worm gear ( 4 in Figure 167 on page 283) to turn the threader mechanism gear ( 6 in Figure 167 on page 283) counterclockwise. This moves the LBA out of the cartridge and past the read/write head. Stop this rotation when the LBA is near the tape guide roller nearest the rear of the drive ( 1 in Figure 168).
1
| | | | | | | | | |
__ 8. Continue rotating the loader motor worm gear ( 1 in Figure 167 on page 283) until the rotate stub ( 3 in Figure 167 on page 283) is positioned as shown. Notice that the rotator stub ( 3 in Figure 167 on page 283) is nearly aligned with the cartridge loader tray guide bearing ( 2 in Figure 167 on page 283). __ 9. Remove the cartridge from the cartridge loader tray. __ 10. Reassemble the drive by reversing the procedure in Step 4 on page 280 in Beginning Procedure. __ 11. Refer to the appropriate procedure to install the new drive and return the failed drive.
284
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a82ru010
| | | | | | | | | | | | | | | | | |
| | | | | | |
__ 7. Turn the supply reel clockwise, carefully guiding the mended portion of the tape to wind around the hub of the supply reel located inside the cartridge. Continue spooling into the cartridge until the tape is taut. The tape must remain within the flanges of the tape guiding rollers. Ensure that you do not stretch the tape. __ 8. Reassemble the drive by reversing the procedure in Step 4 on page 280 in Beginning Procedure.
Appendix: Information for Service Personnel
a82ru008
285
| | | | | | | | | | | | |
__ 9. Allow the drive to perform mid-tape recovery. This takes several minutes. When this activity completes, the cartridge ejects automatically. __ 10. Test the drive to determine if it should be replaced.
| | | | | | | | |
__ 3. From the bottom of the drive, locate the access hole ( 1 in Figure 170). __ 4. Insert a 2.5 mm offset hex wrench through the bottom cover access hole and into the reel motor axle. Begin spooling the tape back into the cartridge by turning the hex wrench clockwise. __ 5. Continue spooling into the cartridge until the tape is taut and remains within the flanges of the tape guiding rollers. Ensure that you do not stretch the tape. __ 6. Locate the threader motor worm gear ( 4 in Figure 171 on page 287) on the rear of the drive. You can either:
286
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a82ru008
| | | | | | |
a. Use your finger to rotate the treader motor worm gear and slowly rotate the threader mechanism gear ( 6 in Figure 171) clockwise; OR b. Use a #1 flathead screwdriver to turn the worm gear ( 9 in Figure 171) clockwise. This rotates the threader motor worm gear ( 4 in Figure 171) clockwise, drawing the LBA into the cartridge.
2 8 6 5 1 9 3 7
| | | | | | | | | | | | | | | | | | |
1 2 3 4 5
Loader motor worm gear Cartridge loader tray guide bearing Rotator stub Threader motor worm gear Threader intermediate gear
6 7 8 9
Threader mechanism gear Lever Loader mechanism gear Threader worm gear
__ 7. As the tape leader block assembly (LBA) is secured in the cartridge, you should hear the LBA retention spring clips click into place. If you do not hear the click, continue rolling until the threader motor worm gear ( 4 in Figure 171) stops. The LBA is in the correct position. Note: Be sure to keep tension on the tape as the LBA is drawn into the cartridge by using a hex wrench as shown in Figure 170 on page 286. __ 8. Notice the: a. Loader mechanism gear ( 8 in Figure 171) nearest the front of the drive that actuates the cartridge loader mechanism.
287
a82ru009
| | | | | | | | | | | | | | |
b. Position of the rotate stub ( 3 in Figure 171 on page 287). c. Front loader motor worm gear ( 1 in Figure 171 on page 287). Rotating this gear allows the loader mechanism gear ( 8 in Figure 171 on page 287) to turn. __ 9. Rotate the loader motor worm gear ( 1 in Figure 171 on page 287) to turn the threader mechanism gear ( 6 in Figure 171 on page 287) counterclockwise. Continue turning until the rotator stub ( 3 in Figure 171 on page 287) loses contact with the lever ( 7 in Figure 171 on page 287). This releases the LBA leader pin. __ 10. Rotate the threader motor worm gear ( 4 in Figure 171 on page 287) to turn the threader mechanism gear ( 6 in Figure 171 on page 287) counterclockwise. This moves the LBA out of the cartridge and past the read/write head. Stop this rotation when the LBA is near the tape guide roller nearest the rear of the drive shown as 1 Figure 172.
1
| | | | | | | | | | |
__ 11. Continue rotating the loader motor worm gear ( 1 in Figure 171 on page 287) until the rotator stub ( 3 in Figure 171 on page 287) is positioned as shown. Notice that the rotator stub ( 3 in Figure 171 on page 287) is nearly aligned with the cartridge loader tray guide bearing ( 2 in Figure 171 on page 287). __ 12. Remove the cartridge from the cartridge loader tray. __ 13. Reassemble the drive by reversing the procedure in Step 4 on page 280 in Beginning Procedure. __ 14. Refer to the appropriate procedure to install the new drive and return the failed drive.
288
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a82ru010
| | |
| | | | | | | | | | | | | | | | | |
__ 2. From the bottom of the drive, locate the access hole ( 1 in Figure 173). __ 3. Insert a 2.5 mm offset hex wrench through the bottom cover access hole and into the reel motor axle. Begin spooling the tape back into the cartridge by turning the hex wrench clockwise. __ 4. Continue spooling into the cartridge until the tape is taut and remains within the flanges of the tape guiding rollers. Ensure that you do not stretch the tape. __ 5. Locate the threader motor worm gear ( 4 in Figure 174 on page 290) on the rear of the drive. You can either: a. Use your finger to rotate the threader motor worm gear and slowly rotate the threader mechanism gear ( 6 in Figure 174 on page 290) clockwise; --OR-b. Use a #1 flathead screwdriver to turn the threader worm gear ( 9 in Figure 174 on page 290) clockwise. This rotates the threader motor worm gear ( 4 in Figure 174 on page 290) clockwise, drawing the LBA into the cartridge.
a82ru008
289
2 8
3 7 6 5
1 9
| | | | | | | | | | | | | | | | | | | | | | | | | |
1 2 3 4 5
Loader motor worm gear Cartridge loader tray guide bearing Rotator stub Threader motor worm gear Threader intermediate gear
6 7 8 9
Threader mechanism gear Lever Loader mechanism gear Threader worm gear
__ 6. As the tape leader block assembly (LBA) is secured in the cartridge, you should hear the LBA retention spring clips click into place. If you do not hear the click, continue rolling until the threader motor worm gear ( 4 in Figure 171 on page 287) stops. The LBA is in the correct position. Note: Be sure to keep tension on the tape as the LBA is drawn into the cartridge by using a hex wrench as shown in Figure 170 on page 286. __ 7. Notice the: a. Loader mechanism gear ( 8 in Figure 174) nearest the front of the drive that actuates the cartridge loader mechanism. b. Position of the rotate stub ( 3 in Figure 174). c. Front loader motor worm gear ( 1 in Figure 174). Rotating this gear allows the loader mechanism gear ( 8 in Figure 174) to turn. __ 8. Rotate the loader motor worm gear ( 1 in Figure 174) to turn the threader mechanism gear ( 6 in Figure 174) counterclockwise. Continue turning until the rotator stub ( 3 in Figure 174) loses contact with the lever ( 7 in Figure 174). This releases the LBA leader pin.
290
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
a82ru009
| | | | | |
__ 9. Rotate the threader motor worm gear ( 4 in Figure 174 on page 290) to turn the threader mechanism gear ( 6 in Figure 174 on page 290) counterclockwise. This moves the LBA out of the cartridge and past the read/write head. Stop this rotation when the LBA is near the tape guide roller nearest the rear of the drive shown as 1 Figure 175.
1
| | | | | | | | | |
__ 10. Continue rotating the loader motor worm gear ( 1 in Figure 174 on page 290) until the rotator stub ( 3 in Figure 174 on page 290) is positioned as shown. Notice that the rotator stub ( 3 in Figure 174 on page 290) is nearly aligned with the cartridge loader tray guide bearing ( 2 in Figure 174 on page 290). __ 11. Remove the cartridge from the cartridge loader tray. __ 12. Reassemble the drive by reversing the procedure in Step 4 on page 280 in Beginning Procedure. __ 13. Refer to the appropriate procedure to install the new drive and return the failed drive.
a82ru010
291
292
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Notices
This information was developed for products and services offered in the U.S.A. IBM may not offer the products, services, or features discussed in this document in other countries or regions. Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead. However, it is the users responsibility to evaluate and verify the operation of any non-IBM product, program, or service. IBM may have patents or pending patent applications covering subject matter described in this document. The furnishing of this document does not give you any license to these patents. You can send license inquiries, in writing, to: Director Intellectual Property & Licensing North Castle Drive Armonk, New York 10504 For more information, please visit: http://www.ibm.com/ibm/licensing/contact/ The following paragraph does not apply to the United Kingdom or any other country or region where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states or regions do not allow disclaimer of express or implied warranties in certain transactions; therefore, this statement may not apply to you. This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice. Any references in this information to non-IBM web sites are provided for convenience only and do not in any manner serve as an endorsement of those web sites. The materials at those web sites are not part of the materials for this IBM product and use of those web sites is at your own risk. IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.
Copyright IBM Corp. 2004, 2005
293
Any performance data contained herein was determined in a controlled environment. Therefore, the results obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurement may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Information concerning non-IBM products was obtained from the suppliers of those products, their published announcements or other publicly available sources. IBM has not tested those products and cannot confirm the accuracy of performance, compatibility or any other claims related to non-IBM products. Questions on the capabilities of non-IBM products should be addressed to the suppliers of those products. All statements regarding IBMs future direction or intent are subject to change or withdrawal without notice, and represent goals and objectives only. All IBM prices shown are IBMs suggested retail prices, are current and are subject to change without notice. Dealer prices may vary. This information is for planning purposes only. The information herein is subject to change before the products described become available. This information contains examples of data and reports used in daily business operations. To illustrate them as completely as possible, the examples include the names of individuals, companies, brands, and products. All of these names are fictitious and any similarity to the names and addresses used by an actual business enterprise is entirely coincidental. If you are viewing this information in softcopy, the photographs and color illustrations may not appear.
Getting Help
If you need assistance while installing or operating your Autoloader, refer to Table 46 and contact the IBM Customer Assistance Center nearest you. When calling for assistance, please have your autoloaders serial number available (located on the label at the inside bottom of the unit).
Table 46. Telephone numbers and e-mail addresses for IBM Customer Assistance Centers World Wide Web Site: http://www.ibm.com/storage/support/lto/ Geographic Location Americas North America South America Hawaii Guam Europe, Middle East, Africa United Kingdom France 01475 898 125 02 3855 7490 tape@uk.ibm.com tape@uk.ibm.com 888 IBM 9585 888 IBM 9585 888 IBM 9585 888 IBM 9585 tape@us.ibm.com tape@us.ibm.com tape@us.ibm.com tape@us.ibm.com IBM Customer Assistance Center Telephone e-mail
294
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Table 46. Telephone numbers and e-mail addresses for IBM Customer Assistance Centers (continued) Italy Republic of Ireland Netherlands Germany Sweden Norway Denmark Finland Asia Pacific Japan Australia New Zealand Other Asia Pacific locations +65 840 9494 +65 840 9494 +65 840 9494 +65 840 9494 tape@sg.ibm.com tape@sg.ibm.com tape@sg.ibm.com tape@sg.ibm.com 02 5962 2122 01 815 9408 020 513 2440 07032 153050 08 793 1081 066 998432 045 233178 09 459 5698 tape@uk.ibm.com tape@uk.ibm.com tape@uk.ibm.com tape@de.ibm.com tape@se.ibm.com tape@se.ibm.com tape@se.ibm.com tape@se.ibm.com
Trademarks
The following are trademarks of International Business Machines Corporation in the United States, other countries (or regions), or both: v IBM v TotalStorage v IBMLink v AS/400 v iSeries v pSeries v xSeries v RS/6000 v SP v zSeries The following are U. S. trademarks of Hewlett-Packard Company, International Business Machines Corporation Corporation, and Seagate Technology: v Linear Tape-Open v LTO v Ultrium Tape Drive Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States, or other countries (or regions), or both. UNIX is a registered trademark of The Open Group in the United States and other countries. Other company, product, and service names may be trademarks or service marks of others.
Notices
295
296
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Dieses Gert ist berechtigt, in bereinstimmung mit dem Deutschen EMVG das EG-Konformittszeichen - CE - zu fhren. Verantwortlich fr die Konformittserklrung nach Paragraph 5 des EMVG ist die: IBM Deutschland Informationssysteme GmbH 70548 Stuttgart. Informationen in Hinsicht EMVG Paragraph 4 Abs. (1) 4: Das Gert erfllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A. EN 55022 Klasse A Gerte mssen mit folgendem Warnhinweis versehen werden: Warnung: dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im Wohnbereich Funkstrungen verursachen; in diesem Fall kann vom Betreiber verlangt werden, angemessene Manahmen durchzufhren und dafr aufzukommen. Anmerkung: Um die Einhaltung des EMVG sicherzustellen, sind die Gerte wie in den IBM Handbchern angegeben zu installieren und zu betreiben.
Notices
297
298
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Any technical or other support provided for a Machine under warranty, such as assistance via telephone with how-to questions and those regarding Machine set-up and installation, is provided WITHOUT WARRANTIES OF ANY KIND.
299
3. where applicable, before service is provided: a. follow the service request procedures that IBM or your reseller provides; b. backup or secure all programs, data, and funds contained in the Machine; c. provide IBM or your reseller with sufficient, free, and safe access to your facilities to permit IBM to fulfill its obligations; and d. inform IBM or your reseller of changes in the Machines location. 4. (a) ensure all information about identified or identifiable individuals (Personal Data) is deleted from the Machine (to the extent technically possible), (b) allow IBM, your reseller or an IBM supplier to process on your behalf any remaining Personal Data as IBM or your reseller considers necessary to fulfill its obligations under this Statement of Limited Warranty (which may include shipping the Machine for such processing to other IBM service locations around the world), and (c) ensure that such processing complies with any laws applicable to such Personal Data.
Limitation of Liability
IBM is responsible for loss of, or damage to, your Machine only while it is 1) in IBMs possession or 2) in transit in those cases where IBM is responsible for the transportation charges. Neither IBM nor your reseller are responsible for any of your confidential, proprietary or personal information contained in a Machine which you return to IBM for any reason. You should remove all such information from the Machine prior to its return. Circumstances may arise where, because of a default on IBMs part or other liability, you are entitled to recover damages from IBM. In each such instance, regardless of the basis on which you are entitled to claim damages from IBM (including fundamental breach, negligence, misrepresentation, or other contract or tort claim), except for any liability that cannot be waived or limited by applicable laws, IBM is liable for no more than 1. damages for bodily injury (including death) and damage to real property and tangible personal property; and 2. the amount of any other actual direct damages, up to the charges (if recurring, 12 months charges apply) for the Machine that is subject of the claim. For purposes of this item, the term Machine includes Machine Code and Licensed Internal Code (LIC). This limit also applies to IBMs suppliers and your reseller. It is the maximum for which IBM, its suppliers, and your reseller are collectively responsible. UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS LIABLE FOR ANY OF THE FOLLOWING EVEN IF INFORMED OF THEIR POSSIBILITY: 1) THIRD PARTY CLAIMS AGAINST YOU FOR DAMAGES (OTHER THAN THOSE UNDER THE FIRST ITEM LISTED ABOVE); 2) LOSS OF, OR DAMAGE TO, DATA; 3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES; OR 4) LOST PROFITS, BUSINESS REVENUE, GOODWILL OR ANTICIPATED SAVINGS. SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. SOME STATES OR JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
300
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Governing Law
Both you and IBM consent to the application of the laws of the country in which you acquired the Machine to govern, interpret, and enforce all of your and IBMs rights, duties, and obligations arising from, or relating in any manner to, the subject matter of this Statement of Limited Warranty, without regard to conflict of law principles. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR JURISDICTION TO JURISDICTION.
Jurisdiction
All of our rights, duties, and obligations are subject to the courts of the country in which you acquired the Machine.
NORTH AMERICA
How to Obtain Warranty Service: The following is added to this Section: To obtain warranty service from IBM in Canada or the United States, call 1-800-IBM-SERV (426-7378). CANADA Limitation of Liability: The following replaces item 1 of this section: 1. damages for bodily injury (including death) or physical harm to real property and tangible personal property caused by IBMs negligence; and Governing Law: The following replaces laws of the country in which you acquired the Machine in the first sentence: laws in the Province of Ontario. UNITED STATES Governing Law: The following replaces laws of the country in which you acquired the Machine in the first sentence: laws of the State of New York.
Notices
301
ASIA PACIFIC
AUSTRALIA What this Warranty Covers: The following paragraph is added to this section: The warranties specified in this Section are in addition to any rights you may have under the Trade Practices Act 1974 or other similar legislation and are only limited to the extent permitted by the applicable legislation. Limitation of Liability: The following is added to this section: Where IBM is in breach of a condition or warranty implied by the Trade Practices Act 1974 or other similar legislation, IBMs liability is limited to the repair or replacement of the goods or the supply of equivalent goods. Where that condition or warranty relates to right to sell, quiet possession or clear title, or the goods are of a kind ordinarily acquired for personal, domestic or household use or consumption, then none of the limitations in this paragraph apply. Governing Law: The following replaces laws of the country in which you acquired the Machine in the first sentence: laws of the State or Territory CAMBODIA, LAOS, and VIETNAM Governing Law: The following replaces laws of the country in which you acquired the Machine in the first sentence: laws of the State of New York, United States of America. CAMBODIA, INDONESIA, LAOS, and VIETNAM Arbitration: The following is added under this heading: Disputes arising out of or in connection with this Statement of Limited Warranty shall be finally settled by arbitration which shall be held in Singapore in accordance with the Arbitration Rules of Singapore International Arbitration Center (SIAC Rules) then in effect. The arbitration award shall be final and binding for the parties without appeal and shall be in writing and set forth the findings of fact and the conclusions of law. The number of arbitrators shall be three, with each side to the dispute being entitled to appoint one arbitrator. The two arbitrators appointed by the parties shall appoint a third arbitrator who shall act as chairman of the proceedings. Vacancies in the post of chairman shall be filled by the president of the SIAC. Other vacancies shall be filled by the respective nominating party. Proceedings shall continue from the stage they were at when the vacancy occurred. If one of the parties refuses or otherwise fails to appoint an arbitrator within 30 days of the date the other party appoints its, the first appointed arbitrator shall be the sole arbitrator, provided that the arbitrator was validly and properly appointed. All proceedings shall be conducted, including all documents presented in such proceedings, in the English language. The English language version of this Statement of Limited Warranty prevails over any other language version. HONG KONG S.A.R. OF CHINA and MACAU S.A.R. of CHINA Governing Law: The following replaces laws of the country in which you acquired the Machine in the first sentence: laws of China (Hong Kong S.A.R.). INDIA Limitation of Liability: The following replaces items 1 and 2 of this section:
302
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
1. liability for bodily injury (including death) or damage to real property and tangible personal property will be limited to that caused by IBMs negligence; and 2. as to any other actual damage arising in any situation involving nonperformance by IBM pursuant to, or in any way related to the subject of this Statement of Limited Warranty, the charge paid by you for the individual Machine that is the subject of the claim. For purposes of this item, the term Machine includes Machine Code and Licensed Internal Code (LIC). Arbitration: The following is added under this heading Disputes arising out of or in connection with this Statement of Limited Warranty shall be finally settled by arbitration which shall be held in Bangalore, India in accordance with the laws of India then in effect. The arbitration award shall be final and binding for the parties without appeal and shall be in writing and set forth the findings of fact and the conclusions of law. The number of arbitrators shall be three, with each side to the dispute being entitled to appoint one arbitrator. The two arbitrators appointed by the parties shall appoint a third arbitrator who shall act as chairman of the proceedings. Vacancies in the post of chairman shall be filled by the president of the Bar Council of India. Other vacancies shall be filled by the respective nominating party. Proceedings shall continue from the stage they were at when the vacancy occurred. If one of the parties refuses or otherwise fails to appoint an arbitrator within 30 days of the date the other party appoints its, the first appointed arbitrator shall be the sole arbitrator, provided that the arbitrator was validly and properly appointed. All proceedings shall be conducted, including all documents presented in such proceedings, in the English language. The English language version of this Statement of Limited Warranty prevails over any other language version. JAPAN Governing Law: The following sentence is added to this section: Any doubts concerning this Statement of Limited Warranty will be initially resolved between us in good faith and in accordance with the principle of mutual trust. MALAYSIA Limitation of Liability: The word SPECIAL in item 3 of the fifth paragraph is deleted. NEW ZEALAND What this Warranty Covers: The following paragraph is added to this section: The warranties specified in this section are in addition to any rights you may have under the Consumer Guarantees Act 1993 or other legislation which cannot be excluded or limited. The Consumer Guarantees Act 1993 will not apply in respect of any goods which IBM provides, if you require the goods for the purposes of a business as defined in that Act. Limitation of Liability: The following is added to this section: Where Machines are not acquired for the purposes of a business as defined in the Consumer Guarantees Act 1993, the limitations in this Section are subject to the limitations in that Act. PEOPLES REPUBLIC of CHINA (PRC)
Notices
303
Governing Law: The following replaces laws of the country in which you acquired the Machine in the first sentence: laws of the State of New York, United States of America (except when local law requires otherwise). PHILIPPINES Limitation of Liability: Item 3 in the fifth paragraph is replaced by the following: SPECIAL (INCLUDING NOMINAL AND EXEMPLARY DAMAGES), MORAL, INCIDENTAL, OR INDIRECT DAMAGES FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES; OR Arbitration: The following is added: under this heading Disputes arising out of or in connection with this Statement of Limited Warranty shall be finally settled by arbitration which shall be held in Metro Manila, Philippines in accordance with the laws of the Philippines then in effect. The arbitration award shall be final and binding for the parties without appeal and shall be in writing and set forth the findings of fact and the conclusions of law. The number of arbitrators shall be three, with each side to the dispute being entitled to appoint one arbitrator. The two arbitrators appointed by the parties shall appoint a third arbitrator who shall act as chairman of the proceedings. Vacancies in the post of chairman shall be filled by the president of the Philippine Dispute Resolution Center, Inc.. Other vacancies shall be filled by the respective nominating party. Proceedings shall continue from the stage they were at when the vacancy occurred. If one of the parties refuses or otherwise fails to appoint an arbitrator within 30 days of the date the other party appoints its, the first appointed arbitrator shall be the sole arbitrator, provided that the arbitrator was validly and properly appointed. All proceedings shall be conducted, including all documents presented in such proceedings, in the English language. The English language version of this Statement of Limited Warranty prevails over any other language version. SINGAPORE Limitation of Liability: The words SPECIAL and ECONOMIC in item 3 in the fifth paragraph are deleted.
304
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
(FYROM), Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia, or Ukraine, you may obtain warranty service for that Machine in any of those countries from either (1) an IBM reseller approved to perform warranty service or (2) from IBM. If you purchase a Machine in a Middle Eastern or African country, you may obtain warranty service for that Machine from the IBM entity within the country of purchase, if that IBM entity provides warranty service in that country, or from an IBM reseller, approved by IBM to perform warranty service on that Machine in that country. Warranty service in Africa is available within 50 kilometers of an IBM approved service provider. You are responsible for transportation costs for Machines located outside 50 kilometers of an IBM approved service provider. Add the following paragraph in Western Europe (Austria, Belgium, Cyprus, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Liechtenstein, Luxembourg, Monaco, Netherlands, Norway, Portugal, Spain, San Marino, Sweden, Switzerland, United Kingdom, Vatican State): The warranty for Machines acquired in Western Europe shall be valid and applicable in all Western Europe countries provided the Machines have been announced and made available in such countries. Governing Law: The phrase the laws of the country in which you acquired the Machine is replaced by: 1) the laws of Austria in Albania, Armenia, Azerbaijan, Belarus, Bosnia-Herzegovina, Bulgaria, Croatia, Georgia, Hungary, Kazakhstan, Kyrgyzstan, FYR Macedonia, Moldova, Poland, Romania, Russia, Slovakia, Slovenia, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, and FR Yugoslavia; 2) the laws of France in Algeria, Benin, Burkina Faso, Cameroon, Cape Verde, Central African Republic, Chad, Comoros, Congo Republic, Djibouti, Democratic Republic of Congo, Equatorial Guinea, French Guiana, French Polynesia, Gabon, Gambia, Guinea, Guinea-Bissau, Ivory Coast, Lebanon, Madagascar, Mali, Mauritania, Mauritius, Mayotte, Morocco, New Caledonia, Niger, Reunion, Senegal, Seychelles, Togo, Tunisia, Vanuatu, and Wallis & Futuna; 3) the laws of Finland in Estonia, Latvia, and Lithuania; 4) the laws of England in Angola, Bahrain, Botswana, Burundi, Egypt, Eritrea, Ethiopia, Ghana, Jordan, Kenya, Kuwait, Liberia, Malawi, Malta, Mozambique, Nigeria, Oman, Pakistan, Qatar, Rwanda, Sao Tome, Saudi Arabia, Sierra Leone, Somalia, Tanzania, Uganda, United Arab Emirates, the United Kingdom, West Bank/Gaza, Yemen, Zambia, and Zimbabwe; and 5) the laws of South Africa in South Africa, Namibia, Lesotho and Swaziland. Jurisdiction: The following exceptions are added to this section: 1)In Austria the choice of jurisdiction for all disputes arising out of this Statement of Limited Warranty and relating thereto, including its existence, will be the competent court of law in Vienna, Austria (Inner-City); 2)in Angola, Bahrain, Botswana, Burundi, Egypt, Eritrea, Ethiopia, Ghana, Jordan, Kenya, Kuwait, Liberia, Malawi, Malta, Mozambique, Nigeria, Oman, Pakistan, Qatar, Rwanda, Sao Tome, Saudi Arabia, Sierra Leone, Somalia, Tanzania, Uganda, United Arab Emirates, West Bank/Gaza, Yemen, Zambia, and Zimbabwe all disputes arising out of this Statement of Limited Warranty or related to its execution, including summary proceedings, will be submitted to the exclusive jurisdiction of the English courts; 3) in Belgium and
Notices
305
Luxembourg, all disputes arising out of this Statement of Limited Warranty or related to its interpretation or its execution, the law, and the courts of the capital city, of the country of your registered office and/or commercial site location only are competent; 4) in France, Algeria, Benin, Burkina Faso, Cameroon, Cape Verde, Central African Republic, Chad, Comoros, Congo Republic, Djibouti, Democratic Republic of Congo, Equatorial Guinea, French Guiana, French Polynesia, Gabon, Gambia, Guinea, Guinea-Bissau, Ivory Coast, Lebanon, Madagascar, Mali, Mauritania, Mauritius, Mayotte, Morocco, New Caledonia, Niger, Reunion, Senegal, Seychelles, Togo, Tunisia, Vanuatu, and Wallis & Futuna all disputes arising out of this Statement of Limited Warranty or related to its violation or execution, including summary proceedings, will be settled exclusively by the Commercial Court of Paris; 5) in Russia, all disputes arising out of or in relation to the interpretation, the violation, the termination, the nullity of the execution of this Statement of Limited Warranty shall be settled by Arbitration Court of Moscow; 6)in South Africa, Namibia, Lesotho and Swaziland, both of us agree to submit all disputes relating to this Statement of Limited Warranty to the jurisdiction of the High Court in Johannesburg; 7) in Turkey all disputes arising out of or in connection with this Statement of Limited Warranty shall be resolved by the Istanbul Central (Sultanahmet) Courts and Execution Directorates of Istanbul, the Republic of Turkey; 8) in each of the following specified countries, any legal claim arising out of this Statement of Limited Warranty will be brought before, and settled exclusively by, the competent court of a) Athens for Greece, b) Tel Aviv-Jaffa for Israel, c) Milan for Italy, d) Lisbon for Portugal, and e) Madrid for Spain; and 9) in the United Kingdom, both of us agree to submit all disputes relating to this Statement of Limited Warranty to the jurisdiction of the English courts. Arbitration: The following is added under this heading: In Albania, Armenia, Azerbaijan, Belarus, Bosnia-Herzegovina, Bulgaria, Croatia, Georgia, Hungary, Kazakhstan, Kyrgyzstan, FYR Macedonia, Moldova, Poland, Romania, Russia, Slovakia, Slovenia, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, and FR Yugoslavia all disputes arising out of this Statement of Limited Warranty or related to its violation, termination or nullity will be finally settled under the Rules of Arbitration and Conciliation of the International Arbitral Center of the Federal Economic Chamber in Vienna (Vienna Rules) by three arbitrators appointed in accordance with these rules. The arbitration will be held in Vienna, Austria, and the official language of the proceedings will be English. The decision of the arbitrators will be final and binding upon both parties. Therefore, pursuant to paragraph 598 (2) of the Austrian Code of Civil Procedure, the parties expressly waive the application of paragraph 595 (1) figure 7 of the Code. IBM may, however, institute proceedings in a competent court in the country of installation. In Estonia, Latvia and Lithuania all disputes arising in connection with this Statement of Limited Warranty will be finally settled in arbitration that will be held in Helsinki, Finland in accordance with the arbitration laws of Finland then in effect. Each party will appoint one arbitrator. The arbitrators will then jointly appoint the chairman. If arbitrators cannot agree on the chairman, then the Central Chamber of Commerce in Helsinki will appoint the chairman. EUROPEAN UNION (EU) THE FOLLOWING TERMS APPLY TO ALL EU COUNTRIES:
306
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Consumers have legal rights under applicable national legislation governing the sale of consumer goods. Such rights are not affected by the warranties provided in this Statement of Limited Warranty. How to Obtain Warranty Service:The following is added to this section: To obtain warranty service from IBM in EU countries, see the telephone listing in Part 3 - Warranty Information. You may contact IBM at the following address:IBM Warranty & Service Quality Dept. PO Box 30 Spango Valley Greenock Scotland PA16 0AH AUSTRIA, DENMARK, FINLAND, GREECE, ITALY, NETHERLANDS, NORWAY, PORTUGAL, SPAIN, SWEDEN AND SWITZERLAND Limitation of Liability: The following replaces the terms of this section in its entirety: Except as otherwise provided by mandatory law: 1. IBMs liability for any damages and losses that may arise as a consequence of the fulfillment of its obligations under or in connection with this Statement of Limited Warranty or due to any other cause related to this Statement of Limited Warranty is limited to the compensation of only those damages and losses proved and actually arising as an immediate and direct consequence of the non-fulfillment of such obligations (if IBM is at fault) or of such cause, for a maximum amount equal to the charges you paid for the Machine. For purposes of this item, the term Machine includes Machine Code and Licensed Internal Code (LIC). The above limitation shall not apply to damages for bodily injuries (including death) and damages to real property and tangible personal property for which IBM is legally liable. 2. UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS LIABLE FOR ANY OF THE FOLLOWING, EVEN IF INFORMED OF THEIR POSSIBILITY: 1) LOSS OF, OR DAMAGE TO, DATA; 2) INCIDENTAL OR INDIRECT DAMAGES, OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES; 3) LOST PROFITS, EVEN IF THEY ARISE AS AN IMMEDIATE CONSEQUENCE OF THE EVENT THAT GENERATED THE DAMAGES; OR 4) LOSS OF BUSINESS, REVENUE, GOODWILL, OR ANTICIPATED SAVINGS. THE FOLLOWING TERMS APPLY TO THE COUNTRY SPECIFIED: FRANCE and BELGIUM Limitation of Liability: The following replaces the terms of this section in its entirety: Except as otherwise provided by mandatory law: 1. IBMs liability for any damages and losses that may arise as a consequence of the fulfillment of its obligations under or in connection with this Statement of Limited Warranty is limited to the compensation of only those damages and losses proved and actually arising as an immediate and direct consequence of the non-fulfillment of such obligations (if IBM is at fault), for a maximum amount equal to the charges you paid for the Machine that has caused the damages. For purposes of this item, the term Machine includes Machine Code and Licensed Internal Code (LIC).
Notices
307
The above limitation shall not apply to damages for bodily injuries (including death) and damages to real property and tangible personal property for which IBM is legally liable. 2. UNDER NO CIRCUMSTANCES IS IBM, ITS SUPPLIERS OR RESELLERS LIABLE FOR ANY OF THE FOLLOWING, EVEN IF INFORMED OF THEIR POSSIBILITY: 1) LOSS OF, OR DAMAGE TO, DATA; 2) INCIDENTAL OR INDIRECT DAMAGES, OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES; 3) LOST PROFITS, EVEN IF THEY ARISE AS AN IMMEDIATE CONSEQUENCE OF THE EVENT THAT GENERATED THE DAMAGES; OR 4) LOSS OF BUSINESS, REVENUE, GOODWILL, OR ANTICIPATED SAVINGS. THE FOLLOWING TERMS APPLY TO THE COUNTRY SPECIFIED: AUSTRIA What this Warranty Covers: The following replaces the first sentence of the first paragraph of this section: The warranty for an IBM Machine covers the functionality of the Machine for its normal use and the Machines conformity to its Specifications.The following paragraphs are added to this section: The warranty period for Machines is 12 months from the date of delivery. The limitation period for consumers in action for breach of warranty is the statutory period as a minimum. In case IBM or your reseller is unable to repair an IBM Machine, you can alternatively ask for a partial refund as far as justified by the reduced value of the unrepaired Machine or ask for a cancellation of the respective agreement for such Machine and get your money refunded. The second paragraph does not apply. What IBM Will Do to Correct Problems: The following is added to this section: During the warranty period, transportation for delivery of the failing Machine to IBM will be at IBMs expense. Limitation of Liability: The following paragraph is added to this section: The limitations and exclusions specified in the Statement of Limited Warranty will not apply to damages caused by IBM with fraud or gross negligence and for express warranty. The following sentence is added to the end of item 2: IBMs liability under this item is limited to the violation of essential contractual terms in cases of ordinary negligence. EGYPT Limitation of Liability: The following replaces item 2 in this section: as to any other actual direct damages, IBMs liability will be limited to the total amount you paid for the Machine that is the subject of the claim. For purposes of this item, the term Machine includes Machine Code and Licensed Internal Code (LIC). Applicability of suppliers and resellers (unchanged). FRANCE Limitation of Liability: The following replaces the second sentence of the first paragraph of this section: In such instances, regardless of the basis on which you are entitled to claim damages from IBM, IBM is liable for no more than: (items 1 and 2 unchanged).
308
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
GERMANY What this Warranty Covers: The following replaces the first sentence of the first paragraph of this section: The warranty for an IBM Machine covers the functionality of the Machine for its normal use and the Machines conformity to its Specifications. The following paragraphs are added to this section: The minimum warranty period for Machines is twelve months. In case IBM or your reseller is unable to repair an IBM Machine, you can alternatively ask for a partial refund as far as justified by the reduced value of the unrepaired Machine or ask for a cancellation of the respective agreement for such Machine and get your money refunded. The second paragraph does not apply. What IBM Will Do to Correct Problems: The following is added to this section: During the warranty period, transportation for delivery of the failing Machine to IBM will be at IBMs expense. Limitation of Liability: The following paragraph is added to this section: The limitations and exclusions specified in the Statement of Limited Warranty will not apply to damages caused by IBM with fraud or gross negligence and for express warranty. The following sentence is added to the end of item 2: IBMs liability under this item is limited to the violation of essential contractual terms in cases of ordinary negligence. HUNGARY Limitation of Liability: The following is added at the end of this section: The limitation and exclusion specified herein shall not apply to liability for a breach of contract damaging life, physical well-being, or health that has been caused intentionally, by gross negligence, or by a criminal act. The parties accept the limitations of liability as valid provisions and state that the Section 314.(2) of the Hungarian Civil Code applies as the acquisition price as well as other advantages arising out of the present Statement of Limited Warranty balance this limitation of liability. IRELAND What this Warranty Covers: The following is added to this section: Except as expressly provided in these terms and conditions, all statutory conditions, including all warranties implied, but without prejudice to the generality of the foregoing all warranties implied by the Sale of Goods Act 1893 or the Sale of Goods and Supply of Services Act 1980 are hereby excluded. Limitation of Liability:The following replaces the terms of section in its entirety: For the purposes of this section, a Default means any act, statement, omission, or negligence on the part of IBM in connection with, or in relation to, the subject matter of this Statement of Limited Warranty in respect of which IBM is legally liable to you, whether in contract or tort. A number of Defaults which together result in, or contribute to, substantially the same loss or damage will be treated as one Default occurring on the date of occurrence of the last such Default. Circumstances may arise where, because of a Default, you are entitled to recover damages from IBM.
Notices
309
This section sets out the extent of IBMs liability and your sole remedy. 1. IBM will accept unlimited liability for death or personal injury caused by the negligence of IBM. 2. Subject always to the Items for Which IBM is Not Liable below, IBM will accept unlimited liability for physical damage to your tangible property resulting from the negligence of IBM. 3. Except as provided in items 1 and 2 above, IBMs entire liability for actual damages for any one Default will not in any event exceed the greater of 1) EUR 125,000, or 2) 125% of the amount you paid for the Machine directly relating to the Default. Items for Which IBM is Not Liable Save with respect to any liability referred to in item 1 above, under no circumstances is IBM, its suppliers or resellers liable for any of the following, even if IBM or they were informed of the possibility of such losses: 1. loss of, or damage to, data; 2. special, indirect, or consequential loss; or 3. loss of profits, business, revenue, goodwill, or anticipated savings. SLOVAKIA Limitation of Liability: The following is added to the end of the last paragraph: The limitations apply to the extent they are not prohibited under 373-386 of the Slovak Commercial Code. SOUTH AFRICA, NAMIBIA, BOTSWANA, LESOTHO AND SWAZILAND Limitation of Liability: The following is added to this section: IBMs entire liability to you for actual damages arising in all situations involving nonperformance by IBM in respect of the subject matter of this Statement of Warranty will be limited to the charge paid by you for the individual Machine that is the subject of your claim from IBM. UNITED KINGDOM Limitation of Liability: The following replaces the terms of this section is in its entirety: For the purposes of this section, a Default means any act, statement, omission, or negligence on the part of IBM in connection with, or in relation to, the subject matter of this Statement of Limited Warranty in respect of which IBM is legally liable to you, whether in contract or tort. A number of Defaults which together result in, or contribute to, substantially the same loss or damage will be treated as one Default. Circumstances may arise where, because of a Default, you are entitled to recover damages from IBM. This section sets out the extent of IBMs liability and your sole remedy. 1. IBM will accept unlimited liability for: (a) death or personal injury caused by the negligence of IBM; and (b) any breach of its obligations implied by Section 12 of the Sale of Goods Act 1979 or Section 2 of the Supply of Goods and Services Act 1982, or any statutory modification or re-enactment of either such Section.
310
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
2. IBM will accept unlimited liability, subject always to the Items for Which IBM is Not Liable below, for physical damage to your tangible property resulting from the negligence of IBM. 3. IBMs entire liability for actual damages for any one Default will not in any event, except as provided in items 1 and 2 above, exceed the greater of 1) Pounds Sterling 75,000, or 2) 125% of the total purchase price payable or the charges for the Machine directly relating to the Default. These limits also apply to IBMs suppliers and resellers. They state the maximum for which IBM and such suppliers and resellers are collectively responsible. Items for Which IBM is Not Liable Save with respect to any liability referred to in item 1 above, under no circumstances is IBM or any of its suppliers or resellers liable for any of the following, even if IBM or they were informed of the possibility of such losses: 1. loss of, or damage to, data; 2. special, indirect, or consequential loss; or 3. loss of profits, business, revenue, goodwill, or anticipated savings.
Warranty Period
The warranty period may vary by country or region and is specified in the tables below. MACHINE TYPE: 3580 IBM TotalStorage Ultrium Tape Drive
Model L11 H11 Warranty Period / Type 1 Year / On-site Exchange 1 Year / On-site Exchange 3 Years / Customer Replaceable Unit n/a n/a 1 Year / On-site Exchange in India and Vietnam with nine (9) hours per business day or next business day excluding holidays 1 Year/On-site Exchange in Japan 3 Years / Customer Replaceable Unit 1 Year / On-site Exchange in India and Vietnam with nine (9) hours per business day or next business day excluding holidays 1 Year/On-site Exchange in Japan 3 Years / Customer Replaceable Unit 1 Year / On-site Exchange in India and Vietnam with nine (9) hours per business day or next business day excluding holidays 1 Year/On-site Exchange in Japan 3 Years / Customer Replaceable Unit 1 Year / On-site Exchange in India and Vietnam with nine (9) hours per business day or next business day excluding holidays 1 Year/On-site Exchange in Japan Exceptions
L13
H13
L23
H23
Notices
311
L13
Customer Carry-In Exchange for Peoples 3 Years/Customer Replaceable Republic of China, Taiwan and China (Hong Unit Kong S.A.R.) Customer Carry-In Exchange for Peoples 3 Years/Customer Replaceable Republic of China, Taiwan and China (Hong Unit Kong S.A.R.) 1 Year/On-site Exchange in India and Vietnam with nine (9) hours per business day or next business day excluding holidays. 1 Year/On-site Exchange in Japan 1 Year/On-site Exchange in India and Vietnam with nine (9) hours per business day or next business day excluding holidays. 1 Year/On-site Exchange in Japan 1 Year/On-site Exchange in India and Vietnam 3 Years/Customer Replaceable with nine (9) hours per business day or next business day excluding holidays. Unit 1 Year/On-site Exchange in Japan 1 Year/On-site Exchange in India and Vietnam 3 Years/Customer Replaceable with nine (9) hours per business day or next business day excluding holidays. Unit 1 Year/On-site Exchange in Japan
H13
L17
1 Year/On-site Exchange
H17
1 Year/On-site Exchange
L23
H23
1 Year/On-site Exchange in India and Vietnam 3 Years/Customer Replaceable with nine (9) hours per business day or next L28/L38/L3H business day excluding holidays. Unit 1 Year/On-site Exchange in Asia Pacific 1 Year/On-site Exchange in India and Vietnam 3 Years/Customer Replaceable with nine (9) hours per business day or next F28/F38/F3H business day excluding holidays. Unit 1 Year/On-site Exchange in Asia Pacific
L23
OPTIONS The following options have a Customer Replaceable Unit Warranty for a period of one (1) year.
IBM TotalStorage Ultrium Machine Type 3580 Tape Drive Option 3580 Rack Mount Kit with Power Cord
312
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
IBM TotalStorage Ultrium Machine Type 3581 Tape Autoloader (models L/H13, L/H 17, L/H23) 3581 Tape Autoloader (models L/H13, L/H 17, L/H23)
Option 3581 Rack Mount Kit with Power Cord 3581 Bar Code Reader 3581 Rack Mount Kit 3581 Bar Code Reader 3581 HVD Converter 3581 Remote Management Unit 3582 Additional LVD Drive 3582 Additional HVD Drive 3582 Additional Fibre Drive 3582 Stand Alone Decorative Cover 3582 Magazine Cover 3582 Remote Management Unit
| | | | | | | |
3581 Tape Autoloader (models L28/L38/L3H, F28/F38/F3H) 3581 Tape Autoloader (models L28/L38/L3H, F28/F38/F3H) 3581 Tape Autoloader (models L28/L38/L3H, F28/F38/F3H) 3581 Tape Autoloader (models L28/L38/L3H, F28/F38/F3H) 3582 Tape Library 3582 Tape Library 3582 Tape Library 3582 Tape Library 3582 Tape Library 3582 Tape Library
Machine Type 3583 IBM TotalStorage Ultrium Scalable Tape Library 3584 IBM TotalStorage Ultrium Ultrascalable Tape Library
Warranty Period/Type 1 Year / On-site Repair Service 1 Year / On-Site Repair Service
Notices
313
(800-463-3339) for specific delivery schedule information. In EMEA and LA countries and/or regions, CRU Service may be via Courier Exchange. (See Courier or Depot Service below.) 2. On-site Repair Service (IOR): On-site repair warranty service is available nine (9) hours per day, five (5) business days per week, next business day response excluding holidays or twenty four (24) hours per day, seven (7) days per week, same day response. IBM or your reseller will repair the failing Machine at your location and verify its operation. You must provide a suitable working area to allow disassembly and reassembly of the IBM Machine. The area must be clean, well lit and suitable for the purpose. For some Machines, certain repairs may require sending the Machine to an IBM service center. 3. On-site Exchange Service (IOE): On-site exchange warranty service is available nine (9) hours per day, five (5) business days per week, the next business day excluding holidays or twenty four (24) hours per day, seven (7) days per week, same day response. IBM or your reseller will exchange the failing Machine at your location and verify its operation. 4. Courier or Depot Service*: You will disconnect the failing Machine for collection arranged by IBM. IBM will provide you with a shipping container for you to return your Machine to a designated service center. A courier will pick up your Machine and deliver it to the designated service center. Following its repair or exchange, IBM will arrange the return delivery of the Machine to your location. You are responsible for its installation and verification. 5. Customer Carry-In (CCR or CCE) or Mail-In Service: You will deliver or mail as IBM specifies (prepaid unless IBM specifies otherwise) the failing Machine suitably packaged to a location IBM designates. After IBM has repaired or exchanged the Machine, IBM will make it available for your collection or, for Mail-in Service, IBM will return it to you at IBMs expense, unless IBM specifies otherwise. You are responsible for the subsequent installation and verification of the Machine. With Customer Carry-In Exchange service (CCIE), the IBM support center will assist with problem determination. When it is determined that a replacement is needed, the IBM support center representative will instruct the customer to bring the failed unit to the nearest IBM authorized service center to exchange for a replacement unit. For calls received by 5:00 p.m. (in the customers time zone) the exchange date can occur within three business days in most cases. While replacing the unit, the customer must transfer the machine type, model number, and serial number of the failing unit to the replacement unit, which is important for future warranty service calls to be handled properly. The customer performs the transfer by writing the information on a repair identification tag that is shipped with the replacement unit and affixing the tag to the replacement unit. The customer should pack the failed unit in the shipping carton that contained the replacement unit, relabel the carton with the shipping label included with the replacement unit, and make arrangements for return of the unit to IBM. Failure to use the carton in which the replacement unit was received or failure to properly pack the returned unit could result in charges incurred by the customer for damage to the failed unit during shipment. Failure to return the failed unit to IBM within 30 days will result in the customer being billed for the replacement unit at IBMs current list price. Transportation charges, both ways, are paid by IBM. The replacement unit becomes the property of IBM.
314
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
* This type of service is called ThinkPad EasyServ or EasyServ in some countries. The customer is responsible for following IBMs published diagnostic procedures in the machines setup and operator guide. Prior to calling the IBM Technical Support Center, the customer should reference service-related information and bulletins on the following IBM LTOTM web site: http://ssddom02.storage.ibm.com/techsup/webnav.nsf/support/lto Customers in Japan should reference the following IBM web site: http://www-6.ibm.com/jp/storage/products/tape/lto/update.html The IBM Machine Warranty worldwide web site at http://www.ibm.com/servers/support/machine_warranties/ provides a worldwide overview of IBMs Limited Warranty for Machines, the Glossary of IBM definitions, Frequently Asked Questions (FAQs) and Support by Product (Machine) with links to Product Support pages.The IBM Statement of Limited Warranty is also available on this site in 29 languages. To obtain warranty service, contact IBM or your IBM reseller. In Canada or the United States, call 1-800-IBM-SERV (426-7378). In the EU countries, see the telephone numbers below. EU Country Telephone List: Phone numbers are subject to change without notice.
Austria -- 43-1-24592-5901 Belgium -- 02-718-4339 Denmark -- 4520-8200 Finland -- 358-9-4591 France -- 0238-557-450 Germany -- 07032-15-4920 Greece -- 30-210-688-1220 Ireland --353-1-815-4000 Italy --39-02-482-9202 Luxembourg -- 352-360385-1 Netherlands --020-514-5770 Portugal -- 351-21-7915-147 Spain --34-91-662-4916 Sweden -- 46-8-477-4420 United Kingdom -- 01475-555-055
Notices
315
316
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Glossary
This glossary defines the special terms, abbreviations, and acronyms that are used in this publication.
American Standard Code for Information Interchange (ASCII). The predominant character-set code of present-day computers. The modern version uses 7 bits for each character (8 bits, if including parity check). The code is used for information interchange among data processing systems, data communications systems, and associated equipment. Arbitrated Loop Topology . A Fibre Channel topology that provides a (FC-AL) solution to attach multiple communicating ports in a loop. Arbitration. The process of selecting one respondent from a collection of several candidates that request service concurrently. archive. To collect and store files in a designated place. ASCII. American Standard Code for Information Interchange. AUTOCLEAN function. A choice on the Autoloaders menu that lets you specify the Autoloader to automatically clean the head of the tape drive with a cleaning cartridge.
Numbers
2:1 compression. The relationship between the quantity of data that can be stored with compression as compared to the quantity of data that can be stored without compression. 3581 Ultrium Tape Autoloader. A device that can be attached to a supported server and used to write data to and from magnetic tape.
A
A. Ampere. AC. Alternating current. AC line voltage. The input voltage (in volts) that is required by the Autoloader for normal operation. activity bars. A graduated series of horizontal bars that appear and disappear at varying rates to signify robotic or drive activity. ACTIVITY light. One of three status lights located on the operator panel of the Autoloader. adapter card. A circuit board that adds function to a computer. ALARM light. One of three status lights located on the operator panel of the Autoloader. The red ALARM light comes on whenever an error occurs. alphanumeric. Pertaining to a character set that contains letters, numerals, and usually other characters, such as punctuation marks. alternating current (ac). An electric current that reverses its direction at regularly recurring intervals. ambient temperature. The temperature of air or other media in a designated area, particularly the area surrounding equipment. amp. Ampere. ampere (A, amp). A unit of measure for electric current that is equivalent to a flow of one coulomb per second, or to the current produced by one volt applied across a resistance of one ohm.
B
BCR . Bar Code Reader. bar code. A code representing characters by sets of parallel bars of varying thickness and separation which are read optically by transverse scanning. bar code label. A specially coded label that can be affixed to a tape cartridge and which enables a device to identify the cartridge and its volume serial number. bar code reader. In the Autoloader, a laser device specialized for scanning and reading bar codes and converting them into either the ASCII or EBCDIC digital character code. bit. Either of the digits 0 or 1 when used in the binary numbering system. browser. A client program that initiates requests to a web server and displays the information that the server returns. burst data transfer rate. In data communications, the average number of bits, characters, or blocks per unit time passing between corresponding equipment in a data transmission system. bus. See SCSI bus.
317
byte. A string consisting of a certain number of bits (usually 8) that are treated as a unit and represent a character. A fundamental data unit.
CRU. See customer replaceable unit. CT. On the left side of the Autoloaders message display, one of three indicators that, when displayed, indicates that drive head needs to be cleaned. current. The quantity of charge per unit time, measured in amperes (Amps, A). customer replaceable unit (CRU). A part that a customer (rather than a service representative) replaces.
C
calibrate. To adjust, tune. capacity. The amount of data that can be contained on storage media and expressed in bytes of data. cartridge. See tape cartridge. cartridge door. On a tape cartridge, a hinged barrier that can be opened to access, or closed to protect, the magnetic tape within the cartridge. cartridge memory. See LTO cartridge memory. cartridge manual rewind tool. A device that can be fitted into the reel of a cartridge and used to rewind tape into or out of the cartridge. cartridge storage slot. One of seven containers that are mounted inside the Autoloader and are used to house tape cartridges. CD. Compact disc. compact disc (CD). A disc, usually 4.75 inches in diameter, from which data is read optically by means of a laser. centimeter (cm). One one-hundredth of a meter (0.01 m). Approximately 0.39 inch. circuit board. A thin plate on which chips and other electronic components are placed. Computers consist of one or more boards, often called cards or adapters. circuit breaker. A switch that automatically interrupts an electric circuit under an infrequent abnormal condition. cleaning cartridge. A tape cartridge that is used to clean the heads of a tape drive. Contrast with data cartridge. cm. Centimeter. compression. The process of eliminating gaps, empty fields, redundancies, and unnecessary data to shorten the length of records or blocks. configure. To describe to a system the devices, optional features, and programs installed on the system. control buttons. Located on the control panel of the Autoloader, four push buttons that, when pressed, let you interact with the menus on the message display. The control buttons are CANCEL, PREVIOUS, NEXT, and ENTER.
D
data. Any representations such as characters or analog quantities to which meaning is, or might be, assigned. data cartridge. A tape cartridge dedicated to storing data. Contrast with cleaning cartridge. data compression. See compression. data transfer rate. See native sustained data transfer rate. DC. On the left side of the Autoloaders message display, one of three indicators that, when displayed, indicates that data compression is selected on the drive. default setting. The value that is assumed when none is explicitly specified. degauss. To make a magnetic tape nonmagnetic by means of electrical coils carrying currents that neutralize the magnetism of the tape. degausser. A device that makes magnetic tape nonmagnetic. device. Any hardware component or peripheral, such as a tape drive or tape library, that can receive and send data. device driver. A file that contains the code needed to use an attached device. DHCP. Dynamic Host Configuration Protocol. An agreed-upon format for assigning IP addresses to devices on a network at the moment they are needed rather than in advance. diagnostic. A software program that is designed to recognize, locate, and explain faults in equipment or errors in programs. Diagnostic Menu. A collection of diagnostic and maintenance functions that the Autoloader can perform. differential. See High Voltage Differential (HVD/DIFF). disable. To make nonfunctional.
| |
318
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
download. To transfer programs or data from a computer to a connected device, typically a personal computer. drive. See IBM Ultrium Tape Drive. drive dump. The recording, at a particular instant, of the contents of all or part of one storage device into another storage device. drive head. The component that records an electrical signal onto magnetic tape, or reads a signal from tape into an electrical signal.
FTP site. Any electronic repository of information that uses the File Transfer Protocol (FTP) for transferring files to and from servers. FMR tape. Firmware upgrade tape.
G
GB. Gigabyte. gigabyte (GB). 1 000 000 000 bytes. grounded. Having or making an electrical connection with the earth.
E
eject. To remove or force out from within. electronic mail. Correspondence in the form of messages transmitted between user terminals over a computer network. e-mail. See electronic mail. enable. To make functional. erase. To remove recorded matter from a magnetic tape. ESD. Electrostatic Discharge.
H
head. See drive head. hertz (Hz). A unit of frequency equal to one cycle per second. High Voltage Differential (HVD/DIFF). A logic signaling system that enables data communication between a supported server and another device, such as the Autoloader. HVD/DIFF signaling uses a paired plus and minus signal level to reduce the effects of noise on the SCSI bus. Any noise injected into the signal is present in both a plus and minus state, and is thereby canceled. Synonymous with differential. host . The controlling or highest-level system in a data communication configuration. Synonymous with server. HVD/DIFF. High voltage differential. Hz. Hertz.
F
fabric. A group of interconnections between fibre channel ports that include a fabric element. Fibre Channel. Up to 2 Gigabit per second data transfer interface technology that maps several common transport protocols including IP and SCSI, allowing it to merge high-speed I/O and network functionality in a single connectivity technology. field microcode replacement (FMR) tape. A tape cartridge that contains new or revised firmware (microcode) for the IBM Ultrium Tape Drive. file. A named set of records stored or processed as a unit. filemark. The size in bytes of the end-of-file (EOF) marks that a tape device writes. file transfer protocol (FTP). In the Internet suite of protocols, an application layer protocol that uses TCP and Telnet services to transfer bulk-data files between machines or servers. firmware. Proprietary code that is usually delivered as microcode as part of an operating system. FMR tape. See field microcode replacement tape.
I
IBM Ultrium Tape Drive. Located within the Autoloader, a data-storage device that controls the movement of the magnetic tape in an IBM LTO Ultrium Tape Cartridge. ID. Identifier. initialize. To format a magnetic tape, write a label (VOLSER) on the tape, and leave the tape empty except for the system files containing the structure information. All former contents of the tape are lost. insert. Pertaining to the Autoloader, to place a tape cartridge into the cartridge storage slot in the autoloader. install. To set up for use or service. The act of adding a product, feature, or function to a system or device either by a singular change or by the addition of multiple components or devices.
Glossary
319
Internet. The worldwide collection of interconnected networks that use the Internet suite of protocols and permit public access. interposer. An adapter-like device that allows a connector of one size and style to connect to a mating connector of a different type and style.
drive one signal over copper wire. The use of wire pairs reduces electrical noise and crosstalk. This method of data transmission requires a cable that is no longer than 25 meters (82 ft). LTO. Linear Tape-Open. LTO-CM. LTO cartridge memory. LTO cartridge memory (LTO-CM). Within each IBM Ultrium Data Cartridge, an embedded electronics and interface module that can store and retrieve a cartridges historical usage and other information. LVD/SE. Low voltage differential/single ended.
K
kg. Kilogram. kilogram (kg). One thousand grams (approximately 2.2 pounds).
L
label. See bar code label. label area. On the LTO Ultrium Tape Cartridge, a recessed area next to the write-protect switch where a label must be affixed. LCD. See liquid crystal display. leader pin. With the LTO Ultrium Tape Cartridge, a small metal column attached to the end of the magnetic tape. LED. Light-emitting diode. light-emitting diode (LED). A semiconductor chip that gives off visible or infrared light when activated. Linear Tape-Open (LTO). A type of tape storage technology developed by the IBM Corporation, Hewlett-Packard, and Certance. line frequency. The frequency (in hertz) of the ac line voltage that the Autoloader requires for normal operation. liquid crystal display (LCD). A low-power display technology used in computers and other I/O devices. load. Pertaining to the Autoloader and following the insertion of a tape cartridge into a cartridge storage slot, the act (performed by the picker) of transferring the cartridge from the storage slot to the drive and of positioning the tape (performed by the tape drive) for reading or writing by the drive head. load and unload cycle. The act of inserting a cartridge into a tape drive, loading the tape to load point, rewinding the tape into the cartridge, and ejecting the cartridge from the drive. Low Voltage Differential/Single Ended (LVD/SE). A low-noise, low-power, and low-amplitude electrical signaling system that enables data communication between a supported server and another device, such as the Autoloader. LVD/SE signaling uses two wires to
M
m. Meter. magnetic tape. A tape with a magnetizable surface layer on which data can be stored by magnetic recording. MB. Megabyte. media. The plural of medium. media capacity. See capacity. media-type identifier. Pertaining to the bar code on the bar code label of the LTO Ultrium Tape Cartridge, a two-character code, Ln, that represents information about the cartridge. L identifies the cartridge as one that can be read by devices which incorporate LTO technology; n indicates the generation level of its type. medium. A physical material in or on which data may be represented, such as magnetic tape. megabyte (MB). 1 000 000 bytes. message display. Located on the operator panel of the Autoloader, an LCD display that provides information about the status of the autoloader and error conditions. metal particle tape. In the LTO Ultrium Tape Cartridge, tape that uses very small, pure metal particles (rather than oxide coatings) in the magnetic layer. meter. In the Metric System, the basic unit of length; equal to approximately 39.37 inches. MODE button. Located on the operator panel of the Autoloader, one of four control buttons that, when pressed, lets you scroll through the commands that you can use to operate the autoloader. Model H13. One of two versions of the Autoloader. The Model H13 uses the Ultra SCSI, High Voltage Differential (HVD/DIFF) SCSI interface. Contrast with Model L13.
320
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Model H23. One of two versions of the Autoloader. The Model 23 uses the Ultra SCSI, High Voltage Differential (HVD/DIFF) SCSI interface. Contrast with Model L23. Model L13. One of two versions of the Autoloader. The Model L13 uses the Ultra2, Low Voltage Differential/Single Ended (LVD/SE) interface. Contrast with Model H13. Model L23. One of two versions of the Autoloader. The Model L23 uses the Ultra160 SCSI, Low Voltage Differential/Single Ended (LVD/SE) interface. Contrast with Model H23.
P
PDF. Portable Document Format. pick. Pertaining to the Autoloader, to remove, by means of a robotic device, a tape cartridge from a storage slot or drive. picker. A robotic mechanism located inside the Autoloader that moves cartridges between the cartridge storage slots and the drive. point-to-point. A topology where two points communicate. port. An access point in a device where a link attaches. Portable Document Format (PDF). A standard specified by Adobe Systems, Incorporated, for the electronic distribution of documents. POST. Power-On Self Test. PostScript. A standard specified by Adobe Systems, Incorporated, that defines how text and graphics are presented on printers and display devices.
N
native data capacity. The amount of data that can be stored without compression on a tape cartridge. native storage capacity. See native data capacity. native sustained data transfer rate. Over a long period of time, the average number of bits, characters, or blocks per unit time passing between corresponding equipment in a data transmission system. NEXT button. Located on the operator panel of the Autoloader, one of four control buttons that, when pressed, highlights the next item or value in the currently displayed menu. node. A fibre channel device that has at least one N_Port or NL_Port noncondensing. A controlled environment that does not permit moisture to condense on the Autoloader or other devices.
| | | |
potentiometer-setting tool. Normally used on a potentiometer to adjust resistance, a tool that is used during the manual removal of a tape cartridge from the Autoloader. POWER button. Located on the operator panel of the Autoloader, a momentary push button switch that lets you turn the power to the autoloader on or off. power cord. A cable that connects a device to a source of electrical power. POWER light. One of three status lights located on the operator panel of the Autoloader. The green POWER light comes on when power is applied to the autoloader. power-off, powered-off. (1) To remove electrical power from a device. (2) The state of a device when power has been removed from it. power-on, powered-on. (1) To apply electrical power to a device. (2) The state of a device when power has been applied to it. Power-On Self Test (POST). A series of diagnostic tests that are run automatically by a device when the power to that device is turned on. power cord plug. On a power cord, the male fitting for making an electrical connection to a circuit by insertion into a receptacle. power receptacle. The mounted female electrical fitting that contains the live parts of the circuit.
Glossary
O
OCP. Operator Control Panel. oersted. The unit of magnetic field strength in the unrationalized centimeter-gram-second (cgs) electromagnetic system. operating environment. The temperature, relative humidity rate, and wet bulb temperature of the room in which the Autoloader routinely conducts processing. operating system. The master computer control program that translates the users commands and allows application programs to interact with the computers hardware. Operator Control Panel. Located on the front of the Autoloader, the functional unit that contains buttons to control the autoloader and a display that provides information about the operation of the autoloader.
321
PREVIOUS button. Located on the operator panel of the Autoloader, one of four control buttons that, when pressed, highlights the preceding item or value in the currently displayed menu. put. Pertaining to the Autoloader, to place, by means of a robotic device, a tape cartridge into a storage slot or drive.
SCSI-2. Small computer systems interface-2. SCSI bus. (1) A collection of wires through which data is transmitted from one part of a computer to another. (2) In networking, a central cable that connects all devices on a local-area network (LAN). (3) A generic term that refers to the complete set of signals that define the activity of the Small Computer Systems Interface (SCSI). Synonymous with SCSI bus cable and SCSI cable. SCSI bus cable. See SCSI bus. SCSI cable. See SCSI bus. SCSI command. An operation performed by a target (tape drive) for an initiator (server). The command is initiated by the operator from the host console. SCSI connector. One of the set of all female and male connectors on the SCSI bus. SCSI device. Anything that can connect into the SCSI bus and actively participate in bus activity. SCSI host adapter card. The logic card that connects a host (server) to the SCSI bus cable. Synonymous with SCSI controller. SCSI ID. The hexadecimal representation of the unique address (0-F) which a user assigns to the Autoloader and which is used in SCSI protocols to identify or select the drive. The user normally assigns and sets the SCSI ID when installing the drive. SCSI wrap tool. A device that attaches to the SCSI connector on the Autoloader and enables internal tests on the SCSI interface. seat, seated. (1) To fit to. (2) To ensure that one object is fitted to another object. SELECT button. Located on the operator panel of the Autoloader, one of four control buttons that, when pressed, activates the currently displayed operation. sensor field. Located on the operator panel of the Autoloader, one of seven numeric fields at the bottom of the display that represent each storage slot and indicate whether a cartridge is present in that slot. A numeric sensor field displays only when a cartridge is present. sequential access. An access technique for retrieving or storing data during which the data is read from, written to, or removed from a file based on the logical order (sequence) of the data in the file. server. A functional unit that provides services to one or more clients over a network. ship group. The group of supplies, cords, or documentation that is shipped with the Autoloader.
R
RID. Repair Identification. RMU. Remote Management Unit. rack. A unit that houses the components of a storage subsystem, such as the Autoloader. rackmount kit. A packaged collection of articles used to install the rack-mounted version of the Autoloader. rackmount tray. A flat-bottomed container with a low rim that holds the Autoloader when it is mounted in a rack. random access. An access technique in which data is obtained from or placed in a storage device in a nonsequential manner. read. To acquire or interpret data from a storage device, from a data medium, or from another source. reinitialize. To reformat a magnetic tape, write a label (VOLSER) on the tape, and leave the tape empty except for the system files containing the structure information. All former contents of the tape are lost. relative humidity. The ratio of the amount of water vapor actually present in the air to the greatest amount possible at the same temperature. remove. Pertaining to the Autoloader, to take a tape cartridge from a cartridge storage slot. retention screws. Pertaining to the connector on a cable, two screws on either side of the connector that secure it to its mating connector. robotics. The picker and any associated mechanisms that move a tape cartridge within the Autoloader. robotics interface. See picker. RPM. Revolutions per minute.
S
scratch cartridge. A data cartridge that contains no useful data, but can be written to with new data. Synonymous with blank cartridge. SCSI. Small computer systems interface.
322
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
shipping environment. The temperature, relative humidity rate, and wet bulb temperature of the environment to which the Autoloader is exposed when being transferred from one location to another. sled. Pertaining to a Autoloader that has been mounted in a rack, the container that houses the autoloader in the rackmount tray. Small Computer Systems Interface (SCSI). A standard used by computer manufacturers for attaching peripheral devices (such as tape drives, hard disks, CD-ROM players, printers, and scanners) to computers (servers). Small Computer Systems Interface-2 (SCSI-2). See Small Computer Systems Interface (SCSI). A standard used by computer manufacturers for attaching peripheral devices (such as tape drives, hard disks, CD-ROM players, printers, and scanners) to computers (servers).
terminator. (1) A part used to end a SCSI bus. (2) A single-port, 75- device that is used to absorb energy from a transmission line. toggle. To alternate between two states. track. A linear or angled pattern of data written on a tape surface. transfer rate. See data transfer rate.
U
U. Pertaining to the rack that houses Autoloader, the amount of space between two holes in a mounting rail. One U is equal to 4.45 cm (1.75 in.). Ultra SCSI. See Small Computer Systems Interface (SCSI). Ultra-2 SCSI. See Small Computer Systems Interface (SCSI). Ultrium Tape Drive. See IBM Ultrium Tape Drive. unattended backup. The act of copying files without operator assistance. uniform resource locator (URL). The address of an item on the World Wide Web. It includes the protocol followed by the fully qualified domain name (sometimes called the host name) and the request. unload. Pertaining to the Autoloader, a term used to describe the act of the drive unthreading the tape from the internal tape path and returning the leader block to the tape cartridge. URL. Uniform resource locator.
| speed matching. The Ultrium 3 and Ultrium 2 Tape | Drive dynamically adjusts its native (uncompressed) | data rate to the slower data rate of a connected server.
status lights. Located on the front of the Autoloader,
| four light-emitting diodes (LEDs) indicate | READY/ACTIVITY (green), CLEAN DRIVE (amber), | MEDIA ATTENTION (amber), and ERROR (red).
storage environment. The temperature, relative humidity rate, and wet bulb temperature of the environment in which the Autoloader is nonoperational and being kept for future use. storage slot. See cartridge storage slot.
T
TapeAlert. A patented technology from Hewlett-Packard that monitors the status of a tape device and media, and detects problems as they occur. TapeAlert flags. Status and error messages that are generated by the TapeAlert utility and display on the host console. tape cartridge. A removable storage device that consists of a tape wound on a supply reel. tape drive. See IBM Ultrium Tape Drive. TB. Terabyte. terabyte. 1 000 000 000 000 bytes. terminate, termination. To prevent unwanted electrical signal reflections by applying a device (a terminator) that absorbs the energy from the transmission line.
V
Vac. Volts of alternating current. Vdc. Volts of direct current. VOLSER. Volume serial number. volume serial number (VOLSER). A number that a computer assigns to a tape cartridge when it prepares (initializes) the cartridge for use. void. In character recognition, the inadvertent absence of ink within a character outline. volt. The SI (international) unit of potential difference and electromotive force, formally defined to be the difference of electric potential between two points of a conductor carrying a constant current of one ampere, when the power dissipated between these points is equal to one watt.
Glossary
323
voltage. The electric potential or potential difference expressed in volts. VPD. Vital Product Data. Settings chosen during configuration of the unit.
W
W. Watts. watt. A metric unit of measure of power; the power required to keep a current of one ampere flowing under a potential drop of one volt; about 1/736 of one horsepower. web. See World Wide Web. wet bulb temperature. The temperature at which pure water must be evaporated at constant pressure into a given sample of air in order to saturate the air under steady-state conditions. Read from a wet-bulb thermometer. World Wide Web. A network of servers that contain programs and files. Many of the files contain hypertext links to other documents available through the network. WP. On the left side of the Autoloaders message display, one of three indicators that, when displayed, indicates that a write-protected cartridge is loaded in the drive. The drive cannot write data to the cartridge. write. To make a permanent or transient recording of data in a storage device or on a data medium. write protected. A tape cartridge is write protected if some logical or physical mechanism causes the device that is processing the tape to prevent the program from writing on the tape. write-protect switch. Located on the LTO Ultrium Tape Cartridge, a switch that prevents accidental erasure of data.
324
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
Index A
ac grounding diagram xvii Access protocol 45 Access Protocol 123, 184 Acoustic Specifications 15 AS/400 system error information Autoloader removing 204 replacing 204 Commands Menu (continued) Model L28/L38/L3H Online 55 BULK EXCHANGE 56 CLEAN DRIVE 58 IMPORT 56 LOAD CARTRIDGE 58 RE-INVENTORY 60 UNLOAD CARTRIDGE 58 Components 7 front panel 7 I/O Door 7 Operator Control Panel 7 POWER button 7 Serial Number 7 interior 8 Carousel 9 Cartridge loader 8 Cartridge slot 8 Ultrium 2 or Ultrium 3 Tape Drive 8 rear panel 10 fan 10 Fibre Channel receptacle 11 HVD Converter (optional) 10 label 10 Power cord receptacle 10 SCSI receptacles 10 serial port 10 Configuration Form 251 Configuration Menu Model F28/F38/F3H Online AUTOLOAD MODE 80 BARCODE READER 82 CHANGE LDR MODE 78 CHANGE LOOP ID 76 DRIVE FW UPGRADE FROM FMR TAPE 78 FIBRE CHANNEL 77 HI SPEED FC 78 LOOP MODE 79 NET PARAMETER 80 PROTECTION MODE 82 RESET 76 SERIAL NUMBER 83 WW NODE NAME 77 Model L28/L38/L3H Online 60 AUTOLOAD MODE 63 BARCODE READER 65 CHANGE LDR MODE 62 CHANGE SCSI ID 61 DRIVE FW UPGRADE FROM FMR TAPE 62 HI SPEED SCSI 61 LOOP MODE 63 NET PARAMETER 64 PROTECTION MODE 66 RESET 60 SERIAL NUMBER 67 Configuring Model F28/F38/F3H 99 change Fibre Channel speed 100 Configuring (continued) Model F28/F38/F3H (continued) change loop ID 99 change operating mode 101 configure BCR 104 configure RMU 103 cycle power 104 enter WW Node Name 100 password protection 105 saving VPD 105 select Fibre Channel port 100 Model L28/L38/L3H 91 change operating mode 92 change SCSI ID 91 change SCSI speed 92 configure BCR 96 configure RMU 95 cycle power 96 password protected login 97 save VPD 97 Models L28/F38/F3H and F28/F38/F3H import cartridges 107 Models L28/L38/L3H and F28/F38/F3H 107 install device drivers 110 My Support registration 121 RMU user accounts 108 to server (host) 110 update firmware 111 Configuring Autoloader 85 Contact Technical Support iii
237
B
Bar Code Label 145 guidelines 146 ordering 160 Bar Code Reader configure 96, 104 installation 25 removing 210 replacing 210 BCR configure 96, 104 removing 210 replacing 210 Buffer internal 4
C
Cartridge acclimation 149 bar code label ordering 160 cleaning 145 data 144 data access, rewind, and load times 4 disposal 158 environmental conditions 149 environmental specifications 151 fill times 4 handling 147 inspection 149 leader pin reattaching 152 repositioning 152 manual removal from drive 270 ordering 159 packaging 148 shipping specifications 151 write-protect switch 147 Cartridges removing manually 266 Channel calibration 4 Checklist Inventory 19 Commands Menu Import 108 Model L28/L:38 Online EXPORT 57 Copyright IBM Corp. 2004, 2005
D
Data Cartridges removing manually 266 Device Drivers download instructions 15 download site 15 downloading 110 installing 110 supported 15 Diagnostic Menu Model L28/L38/L3H Online 67 DRIVE DIAG 70 LOADER DIAG 67 Digital speed matching 3 Drive Dump Log copying to server (host) 185 LTO-TDX 185 via RMU 192 via serial port 187
E
EIA 31 Element Addresses 225 End of Life Plan xviii Environmental Specifications 15
325
Error Codes 01h - 0Fh 169 10h - 1Fh 169 20h - 2Fh 169 30h - 4Fh 170 50h - 6Fh 170 70h - 73h 171 7Ah - 7Fh 171 80h 172 81h - 8Fh 172 90h - 9Fh 173 A0h - AFh 174 Aborted Command 171 Additional 171 Autoloader 168 B0h - B9h 174 BAh - BFh 175 C0h - CFh 175 D0h - DFh 176 drive 179 Drive 175, 176 Electronic Hardware 174 F0h - F3h 176 Function 173 Hardware 170 Illegal Request 170 Low Level Axis 174 Network 176 Not Ready Error 169 Recovered 169 Robotic Control 172 subcodes 176 Unit Attention 169 via RMU 167 view via OCP 166 view via serial port 167 Error Log, Autoloader copying to server (host) 193 via RMU 197 via serial port 193 Error Messages obtaining from host 233 Error Subcodes 176
Fibre Channel cabling 39 Fibre Channel Wrap Test 72 filemarks 4 Firmware updating 111 via RMU 118 via SCSI 118 via serial port 111 FMR Tape code upgrade 264
G
grounding diagram xvii
H
Head Test 71 Home Screen 47 Host Attachment 14 Host Configuration 110 HP-UX system error information HVD Converter 23 removing 214 replacing 214
238
I
Information Menu 49 DRIVE INFO 52 LOADER INFO 50 Inspection power cord 21 power outlet 21 Installation 17 Inventory Checklist 19 iSeries system error information ITDT Tool 118, 185
237
L
Labels bar code 145 guidelines 146 Leader Pin reattaching 152 repositioning 152 LEDs 46 LIBRARY VERIFY 67 Linux error information 239 Location Guidelines Desktop Unit 26 Login OCP 53 Logout 74 LTO-TDX 119 drive dump 120 drive log dump 187 firmware download 120, 186
F
Fan removing 208 replacing 208 Fast R/W Test 72 Features 4 optional 6 Bar Code Reader 6 HVD Converter 6 Rack Mount Kit 6 Remote Management Unit 6 standard 4 built-in diagnostics 6 cartridge inventory 5 eight-cartridge capacity 5 Operator Control Panel 4 Robotic system 4 Ultrium 2 or Ultrium 3 Tape Drive 6 Feedback sending to IBM iii
Media (continued) bar code label (continued) ordering 160 cartridge acclimation 149 disposal 158 environmental conditions 149 environmental specifications 151 inspection 149 packaging 148 shipping specifications 151 cleaning cartridge 145 data cartridge 144 handling cartridges 147 leader pin reattaching 152 repositioning 152 ordering 159 types 11 write-protect switch 147 Media Test 71 Menus 45 Commands Import 108 diagnostic 67 information 49 DRIVE INFO 52 LOADER INFO 50 Model F28/F38/F3H Online 75 Commands 76 Configuration 76 Diagnostic 84 Go Online 84 Information 76 Model L28/L38/L3H Online Commands 55 Configuration 60 Model L28/L38H/L3 Online 55 Offline 49 service 255 Belt Test 256 Clear NVRAM 257 Door Test 256 Gripper Test 256 Load-Unload Test 257 Positions Test 257 Sensor Test 256 Set Log Mode 257 Slider Test 256 My Support iii, 111, 121
N
Normal R/W Test NTUTIL 121 71
O
Obtaining error information AS/400 237 HP-UX 238 iSeries 237 Linux 239 pSeries 233 RS/6000 233 Sun System 238 233
M
Media 143 bar code label 145 guidelines 146
326
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
OCP 46 Home Screen 47 power-up display 47 Offline going 53 Online going 74 Online Menus Model L28/L38/L3H 55 Operating Mode changing 92 Random 63 Operating Modes Automatic 62, 79 Random 79 Sequential 62, 79 Operating Systems supported 14 Operator Control Panel 46 Home Screen 47 power-up display 47 Options HVD converter 23
P
Parts List 217 autoloader 217 power cords 218 Password Protection 53 turn on 97 Passwords 85 OCP 85 RMU 86 Serial Port 86 Physical Specifications 15 Power connecting 36 desktop 36 rack 36 Power Cord Inspection 21 Power Cords 218 Power management 3 Power on 41 Power Outlet Inspection 21 Power Specifications 15 Power-up Display 47 Pre-call Checklist 200 Problem Determination 163 pSeries system error information Publications related xix PWR ON SELF TEST 70
RID Tag attaching 205 RMU Advanced Diagnostics 258 cabling 38 Configuration Menu 130 Device 130 Event Notification 135 Log 134 Network 132 Reset 136 RTC 134 User 133 configure 95 Help 125 Information Menu 126 Autoloader 126 Drive 127 installation 22 login 124 Logout 142 Logs Menu 140 Drive 141 Loader 140 Maintenance Menu 137 Advanced Diagnostic 138 Firmware 139 General Diagnostic 138 Operations 137 Reset 139 Quick Status 125 icons 125 removing 212 replacing 212 saving VPD Model F28/F38/F3H 105 Model L28/L38/L3H 97 Status Menu 128 Autoloader 128 Media 129 using 123 VPD save/restore 41 RS/6000 system error information
SCSI Wrap Test 72 Sense Data 241 Autoloader 241 drive 245 host 249 Serial Cable install 112 Serial Number location of 7 Serial Port Communications 259 Server Attachment 14 Server Configuration 110 Servers supported 14 Service Information 255 Service Menu 255 Belt Test 256 Clear NVRAM 257 Door Test 256 Gripper Test 256 Load-Unload Test 257 Positions Test 257 Sensor Test 256 Set Log Mode 257 Slider Test 256 Service Personnel Information 255 Specifications 15 acoustic 15 environmental 15 physical 15 power 15 Sun System error information 238 support before calling 200 SYSTEM TEST 69
T
Tape Drive interfaces 12 Fibre Channel 13 HVD 12 LVD 13 performance 12 Tape Drive Interfaces 14 connecting 38 TapeAlert Flags 227 Autoloader 227 drive 229 TAPEUTIL 121 technical support before calling 200 Technical Support iii Tests LIBRARY VERIFY 37 Trace Log, Autoloader copying to server (host) 193 via RMU 197 via serial port 193 Troubleshooting BCR problems 198 error messages/codes 166 external fan 197 HVD Converter 199 media problems 199 power 197 pre-call checklist 200 Index
233
S
233 Safety Information xv Caution Notices xv Danger Notices xv End of Life Plan xviii Intended Use xvi Laser Safety and Compliance xvi Precautions xvii Rack Safety 27 Safeguards xvi Safety Inspection Procedure xvii Safety Inspection 203 Safety Inspection Procedure xvii SCSI cabling 38 HVD 39 LVD 38 changing IDs 91, 99 changing speed 92, 100 connecting 38 SCSI Bus Errors 239
R
Rack Mount Kit installation 27 template 253 Rack Template 253 Remove Cartridge from Drive Removing Autoloader 204 Removing External Fan 208 Replacing Autoloader 204 Replacing External Fan 208
270
327
Troubleshooting (continued) RMU problems 198 verifying SCSI IDs 197 Troubleshooting a problem 163
U
Unpacking 18
V
Vital Product Data 251 VPD saving Model F28/F38/F3H 105 Model L28/L38/L3H 97
W
Wrap Tests Fibre Channel 72 SCSI 72 Write-Protect Switch setting 147
328
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide
How satisfied are you that the information in this book is: Very Satisfied Accurate Complete Easy to find Easy to understand Well organized Applicable to your tasks h h h h h h Satisfied h h h h h h Neutral h h h h h h Dissatisfied h h h h h h Very Dissatisfied h h h h h h
h Yes
h No
When you send comments to IBM, you grant IBM a nonexclusive right to use or distribute your comments in any way it believes appropriate without incurring any obligation to you.
Address
___________________________________________________________________________________________________
Fold and _ _ _ _ _ _ _ _ _ _Fold and_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _Please _ _ _ _ _ staple _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Tape _ _ _ _ _ _ _ _ Tape _ _ _ _ do not _ _ _ _ NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES
International Business Machines Corporation Information Development Department GZW 9000 South Rita Road Tucson, Arizona U.S.A. 85775-4401
_________________________________________________________________________________________ Please do not staple Fold and Tape Fold and Tape
GA32-0470-01
Printed in USA
GA32-0470-01
Spine information:
IBM 3581 Autoloader Models L28/L38/L3H and F28/F38/F3H Setup, Operator, and Service Guide