M1000 Automatic Electric Tape Dispenser Manual
M1000 Automatic Electric Tape Dispenser Manual
M1000 Automatic Electric Tape Dispenser Manual
2012
Table of contents
1. Warnings 2. Performance Characteristics 3. Components and Functions Description 4. Auto-feed Operating Steps 4.1. 4.2. 4.3. 4.4. 4.5. 4.6. Under Semi-auto Condition Under Forward Button controlled Condition Replace the Tape When the Tape Got Stuck Replace the Cutting Component Replace the Dispense Roller
Warnings
In order to keep the tape dispenser longer life, the operators should operate the machine following the instruction manual, that's the do's; below is the six don'ts:
Do not use valatile liquids (benzine, thinner, etc) to clean the tape dispenser, Wipe with dry cloth only.
Do not insert bars or plates into the tape outlet, this will damage the blades.
Performance Characteristics
Using the tape dispenser, only need to pull the tape to the tape outlet, the machine will auto dispense the tape at preset length and cut. LED directly displays the size data, the operation is easy to do, the user only needs to press or button then the length is set. (Range: 20mm~999mm)
(After set, press button to begin to cut). Box type cutting parts are convenient to demount and replace. (Simple to deal with the problem of tape get stuck)
Tape Length Display The last digit is MM unit; the first 2 digits are CM unit. Semi-auto Button Press this button, the tape will auto feed and cut to the preset length displays on the digital display. (The pressure
CM and MM button Press the MM button first to set 1 digit millimeter length, and then press the CM button to set 2 digits centimeter digits.
should not exceed 2KG) Back Button To make the feed roller reverse; use the button can replace the tape. Forward Button Press this button can make the tape auto feed forward.
Pressure Knob If the pressure setting crimps the tape, please make the pointer point to (H). Reset Button The length will be set to 20mm. If a bug happens, it will stop working.
4. Press the
5. Set the length of the tape. Press button can set the MM length, the button can set the CM length between 2~99cm. (Under the auto-feed model, the length is better between 2~20cm.) 6. Set the pressure knob according to the tape type, usually set to S (soft). If the pressure knob crimps the tape, make the pointer point to (H).
7. When the auto switch is in the ON position, the tape will auto output and cut to preset length. When the tape in the outlet is taken, the tape dispenser will auto output next part of specific length tape. 8. When the machine is on the fly, please make sure auto-feed switch is at close (semiauto) status. 9. When operate the machine again, press the press button first to cut a little tape, and
Under Semi-auto Condition 1. If the automatic switch is in OFF position, every time the user presses button, the tape dispenser will output a part of tape with preset length. 2. If need a very long part of tape, the user should take the tape front end from the outlet when its outputted. Under Forward Button controlled Condition Keep pressing button until the tape end is outputted, then press button to start cutting. If need to use a long part of tape, take the tapes front from the outlet when its outputted. Replace the Tape Press button to make the roller reverse, then take out the tape by hand.
When the Tape Got Stuck When the tape got stuck, it should press the back forward button the reverse the roller, take out the tape in reverse direction, and then correctly put the tape to the feed roller again. In addition, take down the cutting components; make sure the tape is not sticked on the blade or roller. Replace the Cutting Component 1. Please shut the sensor and turn off the power first and then replace the cutting component. In order to take down the cutting component, the operator should pull out the sensor plugin directly, and then press the button, in the meanwhile, forward pull out the cutting component. (Figure 1)
2. Before remount the cutting component on the main frame, check if the blade is completely dropped. If the blade doesnt drop completely, use a screw driver or sharp end tool to press it down. When remount the component, adjust the bottom of the component to make it fit the main frame, then push the upper part to the frame. (Figure2) 3. Check the insert type of sensor plug; comply with the correct direction to insert the jack on the main frame. After the plug is inserted, it will be easy to mount the cutting component.
Replace the Dispense Roller When replace the dispense roller, make sure the sensitive switch and power switch are turned off. Unpin the sensor plug, take down the cutting component, and then use the cross shaped screw driver to unscrew the 2 screws on Figure 3 marked by arrow. Then, hold the rubber ring on the middle of the dispense roller, pull forward to take down the pedestal body. Take down the screws on the two sides of roller stand, then pull out the collar and wheel gear. (Figure 4)
Announcements
Comply with the above instructions, put the tape correctly. If the tapes front end doesnt fold when putting the tape, it may got stuck at the outlet. Applicative Tape Type Glass paper, manual tape, adhesive plaster, PP paper, double sided tape with interlayer (not thicker than 0.5mm), fibril paper, aluminum paper and crape paper. Since the different type of the tape (some are containing tenacity material), so the tape dispenser may not cut to very exact length as preset. In this case, it needs to adjust the length properly. If the tape is sticked on the blade, take down the cutting component and then coat some silicone oil. 6 / 16 Back to Table of Content
If let the tape dispenser stay in setting status for a long time, its probably lead to paper jam. In this case, press the feed switch. button to cut a little tape, and then turn on the auto
Troubleshooting
If the machine is out of order, please obey the following operating procedures. If the machine is still out of order, please contact us. The engine doesn't run. The machine cant cut tape. The digital tube is not lighting. The tape can't dispense. In "Auto Mode" the machine can't work normally. The tape can't stop dispensing. Check the plug and make sure it's plugged in well; Check the power is turned on Check if all the cutting components are set up correctly. Check the power switch is turned on; Check the plug is plugged in well. Check if the tape is blocked in the roll or cutting components; Check if the tape is put correctly. Check if the plug is plugged in correctly; Check if the Auto/Semi-auto switch is turned on; Check if the tape cutting is working correctly; Check if the sensor is dirty. Check if the tape is off normal from the center; In this case, point the tape to the center of tape outlet, so the sensor can recognize the tape.
Specifications
Commodity Name Display Applicative Tape Width Tape Dimensions Setting Range Motor Color Power Consumption Power Circumstance Light Source Tape dispenser 3 digits digital tube 7~50mm Automatic range: 20~999mm freely setting Adopts DC motor to drive the tape Adopts DC motor to drive cutting blade White Gray 18W AC 110V/60Hz AC220V/50Hz May happens misoperation under filament lamp, suggest to leave far away. Natural Light: 2.000lux 5~40 Less than 80% RH 137mm(W)*218mm(D)*150mm(H) 2.4KG
Assembly Drawing