Nothing Special   »   [go: up one dir, main page]

HilonCare 7200 MC

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

HilonCare 7200

TBT Free Self-Polishing Copolymer Antifouling

Product Description
A TBT free self-polishing antifouling based on Copper Acrylate Copolymer technology, providing long-term antifouling
protection. In compliance with INTERNATIONAL CONVENTION ON THE CONTROL OF HARMFUL ANTI-FOULING SYSTEMS
ON SHIPS, 2001 (IMO document AFS/CONF/26).

Recommended Uses
An antifouling paint used for ship maintenance & repair. Can be applied on the tie coat or the existing antifouling paint in
good condition.

Product Information
Color AF2001 Red
AF2005 Brown
Volume Solids 60%±2%
Typical Film Thickness 75 - 150 microns dry (125 - 250 microns wet)
Theoretical Coverage 8.00 – 4.00m²/litre at 75 - 150 microns dft
Mix Ratio Not applicable
Flash Point 28°C

Surface Preparations
All surfaces to be coated must be clean, dry and free from contamination. High pressure fresh water wash or fresh water
wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with
SSPC-SP1 solvent cleaning.

Newbuilding HilonCare 7200 should be always applied over a recommended primer coating scheme. The
primer surface should be dry and free from all contamination, and HilonCare 7200 must be
applied within the overcoating intervals specified (refer to the relevant product datasheet).
Areas of breakdown, damage etc., should be prepared to the specified standard (e.g., Sa2½
(ISO 8501-1:2007)) and primed prior to the application.
Maintenance & Repair Clean the entire hull area with high pressure (not less than 200kg/cm²) fresh water washing as
soon as the vessel enters dock and before it dries out. Damaged areas should be repaired with
an appropriate anticorrosive primer, and apply HilonCare 7200 within the overcoating interval
specified for the primer (refer to the relevant data sheet).
Others Please consult Hilong representative.

Application
Application Condition The temperature of the substrate should be at least 3°C above the dew point of the air.
After immersed, HilonCare 7200 will exhibit a slight colour change.
Mixing One pack product should always be mixed thoroughly with a power agitator before application.
Induction Period Not applicable
Pot Life (23°C) Not applicable

Page 1 of 2
www.hilonggroup.com
Jul 1,2022
HilonCare 7200
TBT Free Self-Polishing Copolymer Antifouling

Thinner THR200
Airless Spray Recommended
Tip Range 0.54 - 0.79 mm (21 - 31 thou)
Total output fluid pressure at spray tip not less than 170 kg/cm² (2420 p.s.i.)
Brush/Roller Application by brush/roller is recommended for small areas only. Multiple coats may be
required to achieve specified film thickness.

Drying information
Temperature -5℃ 5℃ 25℃ 35℃
Touch Dry 6 hrs 5 hrs 2 hrs 1 hr
Min. Immerse Time(Single Layer) 24 hrs 12 hrs 8 hrs 6 hrs
Min. Immerse Time(Dual Layer) 48 hrs 24 hrs 16 hrs 12 hrs

Note: For Major Refurbishment and Repair if total dft is﹥300μm flood times must be increased as follows:
72 hours at -5°C, 48 hours at 5°C, 36 hours at 25°C and 24 hours at 35°C.

Overcoating Data
Temperature -5℃ 5℃ 25℃ 35℃
Min. Max. Min. Max. Min. Max. Min. Max.
HilonCare 7200 20 hrs 6 mths 12 hrs 6 mths 6 hrs 6 mths 4 hrs 3 mths

Unit Size
20 litres unit: 20 litres in a 20 litres container.

Storage
Must be stored in accordance with national regulations. Store in dry, shaded conditions away from sources of heat and
ignition.

Health And Safety


Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety informa-
tion, and apply and use the coating according to the national state of health and safety as well as environmental protection
standards and regulations.

Important note
The information in this data sheet is not intended to be exhaustive, for your reference only. The information contained in this
data sheet is liable to modification from time to time in the light of experience and our policy of continuous development.
Please contact us and request the latest version prior to using the product.

Page 2 of 2
www.hilonggroup.com
Jul 1,2022

You might also like