E-Program Files-AN-ConnectManager-SSIS-TDS-PDF-Interlac - 800 - Eng - A4 - 20100308
E-Program Files-AN-ConnectManager-SSIS-TDS-PDF-Interlac - 800 - Eng - A4 - 20100308
E-Program Files-AN-ConnectManager-SSIS-TDS-PDF-Interlac - 800 - Eng - A4 - 20100308
Alkyd
PRODUCT A single component, high solids, low VOC, 30% silicone content, modified alkyd.
DESCRIPTION
INTENDED USES Interlac 800 offers a high gloss interior/exterior finish for use on properly prepared and primed
metal, masonry and wood surfaces. Exhibits a higher level of heat resistance, gloss and colour
retention when compared to other alkyd coatings. Easy to apply and recoat. Low VOC.
Suitable for storage tanks, piping, machinery and equipment in petrochemical and power industries,
which require a level of heat and ultraviolet light resistance beyond that of traditional alkyds.
Theoretical Coverage 15.90 m²/litre at 37 microns d.f.t and stated volume solids
639 sq.ft/US gallon at 1.5 mils d.f.t and stated volume solids
Protective Coatings
Page 1 of 4
Issue Date:08/03/2010
Ref:2225
Interlac® 800
Alkyd
SURFACE All surfaces to be coated should be clean, dry and free from contamination. Prior to paint
PREPARATION application all surfaces should be assessed and treated in accordance with ISO 8504:2000.
Primed Surfaces
Interlac 800 should always be applied over a recommended anti-corrosive coating scheme. The
primer surface should be dry and free from all contamination and Interlac 800 must be applied
within the overcoating intervals specified (consult the relevant product data sheet).
Areas of breakdown, damage etc., should be prepared to the specified standard (e.g. Sa2½ (ISO
8501-1:2007) or SSPC SP6 Abrasive Blasting or SSPC SP11, Power Tool Cleaning) and patch
primed prior to the application of the product.
APPLICATION Mixing This material is a one component coating and should always be mixed
thoroughly with a power agitator before application.
Clean Up Clean all equipment immediately after use with International GTA007. It is
good working practice to periodically flush out spray equipment during the
course of the working day. Frequency of cleaning will depend upon amount
sprayed, temperature and elapsed time, including any delays.
Page 2 of 4
Interlac® 800
Alkyd
PRODUCT Level of sheen and surface finish are dependent on application method. Avoid using a mixture of
CHARACTERISTICS application methods whenever possible.
As with all alkyd systems, Interlac 800 has limited chemical and solvent resistance and is not
suitable for use in immersion situations or in conditions of continuous condensation.
Surface temperature must always be a minimum of 3°C (5°F) above dew point.
For brush and roller application, and in some colours, two coats of Interlac 800 may be required to
give uniform coverage.
USDA approval for incidental food contact surface in federally inspected meat and poultry plants.
Subject to Inspector-In-Charge approval.
Note: VOC values are typical and are provided for guidance purpose only. These may be subject
to variation depending on factors such as differences in colour and normal manufacturing
tolerances.
Low molecular weight reactive additives, which will form part of the film during normal ambient cure
conditions, will also affect VOC values determined using EPA Method 24.
SYSTEMS Interlac 800 is only suitable for application over alkyd or oleoresinous priming systems, e.g.:
COMPATIBILITY
Interprime 198
Interprime 234
Interlac 800 is not normally topcoated with products other than itself.
Page 3 of 4
Interlac® 800
Alkyd
D ADDITIONAL Further information regarding industry standards, terms and abbreviations used in this data sheet
et INFORMATION can be found in the following documents available at www.international-pc.com:
ail
T • Definitions & Abbreviations
o
p • Surface Preparation
• Paint Application
SAFETY This product is intended for use only by professional applicators in industrial situations in
PRECAUTIONS accordance with the advice given on this sheet, the Material Safety Data Sheet and the
container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS)
which International Protective Coatings has provided to its customers.
All work involving the application and use of this product should be performed in compliance with all
relevant national, Health, Safety & Environmental standards and regulations.
In the event welding or flame cutting is performed on metal coated with this product, dust and
fumes will be emitted which will require the use of appropriate personal protective equipment and
adequate local exhaust ventilation.
If in doubt regarding the suitability of use of this product, consult International Protective Coatings
for further advice.
Rect Top
PACK SIZE Unit Size
Vol Pack
1 US gal 1 US gal 1 US gal
5 US gal 5 US gal 5 US gal
, International and all product names mentioned in this publication are trademarks of, or licensed to, AkzoNobel.
www.international-pc.com
Page 4 of 4