PM Is 6911
PM Is 6911
PM Is 6911
132893/2022/CMD-II
PM/ 6911/4
July 2022
www.bis.gov.in
उ�ाद मानु यल
Stainless Steel Plate, Sheet
and StripIS
6911:2017 के अनुसार
िविभ� उ�ादों के िलए भारतीय मानक �ूरो (अनु�पता मू�ांकन) िविनयम, 2018 की योजना- I के
तहत प्रमाणन के सं चालन म� अ�ास और पारदिश�ता के सं चालन म� पारदिश�ता सु िनि�त करने के िलए
इस उ�ाद मैनुअल का उपयोग सभी �े त्रीय / शाखा काया�लयों और लाइस� सधा�रयों �ारा सं दभ� सामग्री
के �प म� िकया जाएगा। द�ावे ज़ का उपयोग बीआईएस प्रमाणन लाइस� स/प्रमाणपत्र प्रा� करने के
इ�ु क सं भािवत आवे दकों �ारा भी िकया जा सकता हैI
This Product Manual shall be used as reference material by all Regional/Branch Offices & licensees
to ensure coherence of practice and transparency in operation of certification under Scheme-I of
Bureau of Indian Standards (Conformity Assessment) Regulations, 2018 for various products. The
document may also be used by prospective applicants desirous of obtaining BIS certification
licence/certificate.
1. उ�ाद : IS 6911:2017
Product
शीष�क : Stainless Steel Plate, Sheet and Strip
Title
संशोधनों की सं�ा : 3
No.of amendments
2. नमू ना िदशािनद� श
Sampling Guidelines
a) क�ामाल : No specific requirement for raw material
Raw material
b) समूहीकरण िदशािनद� श : Please refer Annex - A
Grouping Guidelines
c) नमू ने का आकार : 5 pieces of 5 cm x 5 cm for chemical tests
Sample Size 0.5 m x 0.5 m for mechanical tests (Prepared tests for
pieces for thickness > 4 mm)
Licence is granted to use Standard Mark as per IS 6911:2017 with the following scope:
उ�ाद का नाम Stainless Steel Plate, Sheet and Strip
Name of the product
Grade designation 301, 302, 304S1..
ANNEXURE A
TO PRODUCT MANUAL FOR
Stainless Steel Plate, Sheet and Strip
According to IS 6911:2017
GROUPING GUIDELINES
Grouping of different grade designations of stainless steel has been done on the basis of phase of iron
and chemical composition/alloying elements. Guidelines for drawing of samples for each group are as
under:
1
829
132893/2022/CMD-II
6 Duplex One sample each from the group, of hot rolled and cold rolled
conditions, of any heat treatment process if so followed by the
manufacturer, of any one of the grade designations, of Stainless Steel
Plate, Sheet and Strip, as applied for licence/inclusion may be drawn and
to be tested for all requirements of the specification applicable
to the variety tested.
Note: 200-Austenitic grade designation series refers to all austenitic type grades bearing numerical
symbol of the type 2xxx.. such as 201, 201A, 204Cu1 etc., Similarly for 400-Ferritic, 400-martensitic,
300-austenitic, 900-austenitic etc.
2. During preliminary inspection, before drawing samples for independent testing, it shall be ensured by
IO that samples to be drawn for independent testing have to be tested at factory for Dimensions as per
cl.17 of IS 6911:2017. In case of inclusion, factory test report for Dimensions as per cl.17 of IS
6911:2017 may be accepted and conformity of the grades included to the same has to be verified during
next surveillance visit.
3. Surface Finish: Certain surface finishes get converted to superior surface finishes based on further
processing. Further, some surface finishes are independent of each other. Hence, recommendation on
polished finishes shall be restricted depending upon the manufacturing facility available with the firm.
Note: If no heat treatment is involved while changing the appearance to superior surface finish then test
requirements of previous finish is to be made applicable for superior finish as well.
4. A declaration shall be obtained from the applicant on each heat treatment process (Annealing,
Hardened and tempered or any other treatment), based on the manufacturing capabilities, exercised for
each group.
5. If the above sample passes, then licence may be granted/inclusion be done for the Grades
designations, for all sizes and varieties of the Group. However, it shall be ensured that the firm is
having all the necessary manufacturing and testing facilities for the manufacture and testing of the
sizes/grade designations /varieties of Stainless Steel Sheet and Strip to be included in the licence.
2
830
132893/2022/CMD-II
ANNEXURE B
TO PRODUCT MANUAL FOR
Stainless Steel Plate, Sheet and Strip
According to IS 6911:2017
OR
3
831
132893/2022/CMD-II
Glass.
Apparatus for corrosion resistance test
4
832
132893/2022/CMD-II
ANNEXURE B
TO PRODUCT MANUAL FOR
Stainless Steel Plate, Sheet and Strip
According to IS 6911:2017
1. Strohlein or Leco apparatus with all attachments Barometer cl.8.1, 8.2 – C & S
with chart, Hot plate, Muffle furnace, Complete range of
glass wares, measuringcylinders, Desiccator, porcelain (chemical method, alternative to
boats or ceramic crucibles, Thermometer, Electronic instrumental method)
Balance, Distilled Water, Hot air oven, Oxygen - 99.5
percent minimum purity, ether or acetone Standard
Reference Material (NML) with certificateReagents for C:
tin granules or pure iron fillings, acidulated water/brine
water, methyl red, caustic potashReagents for S: Ceramic
boats/crucibles – desiccators, Fluxes -Low sulphur copper,
tin or iron, Dilute hydrochloric acid, Starch Iodide solution,
Potassium iodate
Weighing balance, Heater/ Heating element along with Phosphorus content Cl 8.1,8.2
energy regulator, Ice water bath, Vol Flask Cap – 1 litre,
(Whatman) filter paper No. 040, Suction Filtration Facility, (chemical method, alternative to
Filter paper pulp pad, Standard Reference Material (NML) instrumental method)
with certificate, Potassium Permanganate (KMnO4),
Sodium Nitrite (Na2NO3), Ammonium Molybdate [(NH4)2
Mo2O7], Ammonium Phosphate [(NH4)3 PO4], Potassium
Nitrate (K2NO3), Phenolphthalein Solution, Rectified spirit
or methyl alcohol, Sodium Hydroxide (NaOH),
Hydrofluoric Acid (HF), Perchloric Acid (HClO4),
Sulphurous Acid, ,Hydrobromic Acid (HBr) , other
chemicals and reagent as applicable
2.
Hot plate, Conical flask Manganese content Cl 8.1,8.2
5
833
132893/2022/CMD-II
Reagents: ammonium nitrate, methyl red, dilute ammonium (chemical method, alternative to
hydroxide, Concentrated hydrochloric acid Concentrated instrumental method)
nitric acid, Perchloric acid, Hydrofluoric Acid
6.
Hot plate, stop watch Cr content Cl 8.1,8.2
Reagents: dilute sulphuric acid and phosphoricacid mixture, (chemical method, alternative to
concentrated nitric acid, ammonium persulphate , silver instrumental method)
nitrate, dilute hydrochloric acid, ferrous ammonium
sulphate, standard potassium permanganate solution.
7.
Nitrogen content shall be occasionally tested.
Note:
1. This is an indicative list for the purpose of guidance only and may not be taken as exhaustive
2. In case of Test method as per IS 228 is followed, facility/alternate arrangement for Al( in case
of Al-killed), Nitrogen testing and Microalloying elements to be verified, accordingly scope of
licence to be defined.
6
834
132893/2022/CMD-II
ANNEXURE C
TO PRODUCT MANUAL FOR
Stainless Steel Plate, Sheet and Strip
According to IS 6911:2017
1. LABORATORY – A laboratory shall be maintained which shall be suitably equipped (as per the
requirement given in Column 2 of Table-1) and staffed, where different tests given in the specification
shall be carried out in accordance with the methods given in the specification.
The manufacturer shall prepare and implement a calibration plan for the test equipment.
2 TEST RECORDS The manufacturer shall maintain test records for the tests carried out to establish
conformity.
3 LABELLING AND MARKING : The Standard Mark as given in Schedule of the license and
Licence Number (i.e. CM/L….............) shall be incorporated, and the marking shall be done as per the
provisions of the Indian Standard, provided always that the product thus marked conforms to all the
requirements of the specification. In addition, details of BIS website shall be marked as follows: “For
details of BIS certification please visit www.bis.gov.in”
4 CONTROL UNIT: For the purpose of this scheme the material or part thereof representing the same
cast, condition and form processed to same nominal thickness and same surface finish, shall constitute a
control unit
5 LEVELS OF CONTROL - The test and inspection indicated in Table 1 attached and at the levels of
control specified therein shall be carried out on the whole production covered under this scheme and
appropriate records maintained in accordance with paragraph 2 above..
6. TEST CERTIFICATE-
i) For each consignment of BIS Certified material conforming to this specification there shall be a test
certificate which shall contain the Standard Mark, the lot/cast number and the corresponding test
results (as given in Annexure I enclosed).
ii) In cases where the Stainless Steel coil/plate is procured from outside as raw material for further
rolling, the coil/plate procured shall be ISI marked only as per IS 6911. Further, the ISI marked test
certificate of the raw material coil/plate shall also be enclosed along with the above test certificate in
case of all consignments.
iii) The above provisions are equally applicable for both domestic and foreign manufacturers.
8
836
132893/2022/CMD-II
SCHEME OF INSPECTION AND TESTINGFOR CERTIFICATION
OF IS 6911:2017
Table 1: Levels of Control
(In addition to the test requirements given below, there may be other requirements in the Standard forexample clause 5 (Manufacture) for
which compliance is to be ensured and demonstrated to BIS)
Such manufacturers
must ensure that the
raw material stainless
steel coils/plates
procured by them are
ISI marked only as per
IS 6911 and are
received with test
certificate.
Note-1: Whether test equipment is required or sub-contracting is permitted in column 2 shall be decided by the Bureau and shall be
mandatory. Sub-contracting is permitted to a laboratory recognized by the Bureau or Government laboratories empaneled by the Bureau.
Note-2: The control unit and levels of control as decided by the Bureau are obligatory to which the licensee shall comply with.
PM/ 6911/2 839
132893/2022/CMD-II April 2021
ANNEXURE – I
(PARA 6 OF THE SCHEME OF INSPECTION AND TESTING)
XYZ IRON AND STEEL COMPANY
(REGD OFFICE AND WORKS ADDRESS)
TO M/S
We certify that the material below fully conforms to IS 6911:2017. Chemical and mechanical properties of the product, tested in
accordance with the Scheme of Inspection and Testing contained in the BIS certification marks licence no. CM/L- are as
indicated below against each order
(PLEASE REFER TO 6911:2017 FOR SPECIFICATION REQUIREMENTS)
TEST RESULTS
Order No. Type and Size Control Unit Grade, Qty Chemical Composition (in % by wt) Mechanical
No. condition, heat properties
treatment,
surface finish
Si
Mn
Ni
Cr
Mo
N
Cu
Ors
Hardness
YS
TS
Elongatio
REMARKS
WAGON NO.
TRUCK NO. FOR XYZ IRON AND STEEL COMPANY
(It is suggested that size A4 paper be used for this test certificate)