Final - Electronics10 - q4 - Mod3 - Principle Operation of A Robotic Motor 1 - May 8 122023
Final - Electronics10 - q4 - Mod3 - Principle Operation of A Robotic Motor 1 - May 8 122023
Final - Electronics10 - q4 - Mod3 - Principle Operation of A Robotic Motor 1 - May 8 122023
Electronics
Quarter 4 – Module 3:
Operation Principle of a Robotic
Motor
This module was designed and written with you in mind. It is here to help
you master the Principle Operation of a Robotic Motor. The scope of this module
permits it to be used in many different learning situations. The language used
recognizes the diverse vocabulary level of students. The lessons are arranged to
follow the standard sequence of the course. But the order in which you read them
can be changed to correspond with the textbook you are now using.
1. Discuss the principle of operation of the motor used for the robot.
What I Know
Directions: Read each question carefully. Choose the letter of the correct answer.
1. Which part is considered as one of the vital components that enable robots to
move?
a. axle
b. motor
c. sensor
d. stator
2. Which part of the motor measures the amount of force that it can produce or
exert?
a. armature
b. commutator
c. speed
d. torque
3. What do you call the central shaft of an electric motor?
a. armature
b. axle
c. rotor
d. terminal
1
4. What do you call the part of the electric motor that is stationary and does not
move?
a. brushes
b. commutator
c. rotor
d. stator
5. Which part connects the point between the battery and the motor to relay power
to the motor?
a. armature
b. brushes
c. copper coil
d. terminal
6. What unit is used in counting the number of times the axle spins per minute?
a. ACM
b. ECM
c. MAS
d. RPM
7. Which of the following is NOT a part of an electric motor?
a. alternator
b. armature
c. commutator
d. stator
8. Which component is found inside the stator of the motor?
a. axle
b. battery
c. copper coils
d. magnets
9. Which part of the motor is located at one end of the coil and made of a metal
ring divided into two equal parts?
a. armature
b. axle
c. battery
d. commutator
10. Which of the following supplies the electric current to the motor?
a. axle
b. battery
c. magnets
d. terminals
2
Lesson The Principle Operation of a
1 Robotic Motor
What’s In
There are two pictures shown below, a hard disc drive and a laser printer
head motor. Identify which one uses a Stepper motor and which uses a Servo
motor. Explain your answer briefly.
Figure1: Hard disc drive
_____________________________________________
_____________________________________________
Source: https://rb.gy/u5nllm
___________________________________________
3
____________________________________________
Source: https://rb.gy/bdkrb4
Guide Questions:
1. What is a stepper motor?
2. What is a servo motor?
3. What loop mechanism is missing in a stepper motor?
What’s New
Activity 1: Motor-rific!
Directions: In this activity, you will try to identify devices or machines found in
your home that use an electric motor. List them all inside the picture.
Guide Questions:
1. What are three (3) devices or machines that you operate every day based on
your list? Why do you use them daily?
4
2. In your opinion, what are the advantages of using devices and machines run
by a motor?
3. In your opinion, what are the disadvantages of using devices and machines
run by a motor?
What is It
Motors are one of the vital components that enable robots to move. Some
motors connected to wheels help robots to move around. Others are used in
making robotic joints and limbs. Although there are different types of sensors used
by robots to perform various tasks, they still need electric motors to move around.
Motors convert electrical energy to mechanical energy that enabling the
robot to do programmed work. We must understand two concepts to anticipate how
much work a robot can do.
Speed refers to the maximum speed a motor can reach and is measured in
revolutions per minute (RPM). One (1) RPM means that the motor's axle will turn
around a circle once in a minute, which is very slow. Motors powered by direct
current (DC) can have a speed rating of at least 1000 RPMs.
Torque measures how much force that a motor can produce or exert. One
way to show this is if you attach an arm with a weight on it to the motor's axis, see
how much weight the motor can lift. Commonly, speed and torque would have an
inverse relationship, meaning as speed increases, torque decreases. Because of this
concept, there should be a balance between speed and torque when constructing a
robot. Gears can help in converting speed to torque or torque to speed.
In general, motors enable robots to move. Several robotic applications use a
specific motor to accomplish a task. Each type of motor performs different
functions. In selecting the correct electric motor to fit in the robot, consider the
following: the load that a specific motor can handle, the torque needed to move the
robot without being overloaded, the rotations per minute of the motor when it is
running.
5
Source: https://rb.gy/vghbub
Figure 3. The Pictorial Diagram of Internal Components of an Electric Motor.
Parts of an Electric Motor
The design of the electric motor has undergone various upgrades yet its’
basic components remained the same. The basic parts include an armature or a
rotor, a commutator, brushes, an axle, a stator, electrical terminals, and a DC
power supply. Together, these parts utilize the attractive and repulsive forces of
electromagnetism, causing the motor to continuously spin as it receives a steady
flow of electric current from the power supply. The electric motor has two parts:
one stationary part called the stator, and the other is the one that spins. The stator
is often a permanent magnet or a row of magnets lining the edge of the motor
casing a round plastic drum. Inside the stator is the rotor or armature that spins
as the motor is running. It is made of copper wire wound into a coil around an axle.
The axle is the central shaft of the motor. As the electric current flows through the
coil, the resulting magnetic field pushes against the field created by the stator and
makes the axle spin.
An electric motor has another vital component, the commutator. It is located
at one end of the coil. It is composed of a metal ring divided into two halves. It
reverses the electrical current in the coil each time the coil rotates half a turn. The
commutator periodically reverses the current between the rotor and the external
circuit or the battery. These will guarantee that the coils' ends do not move in
opposite directions and that the axle spins in one direction only.
At the other end of the motor, we find the brushes and the terminals. They
are at the opposite end from where the rotor exits the motor casing. The brushes
relay the electrical current to the commutator. The terminals are connected to
where the battery is attached. It provides the current that enables the rotor to spin.
6
becomes electrically negative. As opposite poles attract one another and like poles
repel, when you surround the axle with another magnet, it will move back and
forth from negative to positive. These will instigate an attractive and repulsive force
causing the axle to rotate, thus causing the motor to work.
Source: https://rb.gy/blhcro
What’s More
7
8. It is the central shaft of an electric motor.
9. They are considered as one of the vital components that enable robots to move.
10. It is located at one end of the coil composed of a metal ring divided into two
halves. It reverses the electrical current in the coil each time the coil rotates half
a turn.
Guide Questions:
1. What are the two (2) parts of an electric motor?
2. What is the function of each part of an electric motor?
3. In your opinion, if one part of the motor stops working, what will happen to
the
motor? Explain further.
Assessment 1:
Directions: Read the following questions and choose the correct answer.
1. What energy do motors convert into electrical energy?
a. heat c. mechanical
b. kinetic d. solar
2. Which of the following is the stationary component inside the motor?
a. alternator c. copper wire coil
b. battery d. stator
3. What describes the maximum RPM a motor can reach?
a. acceleration c. speed
b. momentum d. torque
4. What do we call the stationary component inside the motor?
a. axle c. rotor
b. commutator d. stator
5. Which of the following is NOT a component of an electrical motor?
a. commutator c. rotor
b. electrical terminals d. thermostat
Source: https://rb.gy/nkqvl
8
Figure 5: A cross-section of an electric motor.
Guide Questions:
1. What are the stationary parts of a motor? Why are they not moving?
2. What are the moving parts of the motor? Why are they moving??
3. In your opinion, can electric motors work underwater? Explain further.
Activity 3. What do you see?
Directions: Write the word that corresponds to each letter as a missing word to
complete the sentences. Use the word bank to help you fill in the
statements.
WORD BANK:
a. armature i. electromagnetism
b. axle j. electromagnetic field
c. battery k. magnets
d. commutator l. repulsive
e. copper wire m. stationary
f. DC power n. stator
g. direction o. terminals
h. electrical current
9
Guide Questions:
1. Do you think that motors can run without electricity? Why do you think so?
2. Do you think that robots can move without motors? Why do you think so?
3. How important are magnets in an electric motor?
Directions: Arrange the following steps into the correct sequence to describe how
an electric motor works.
A B C D
1.The robot is traveling at high speed on sandy soil under the hot Sun for 30
minutes.
2.The robot is crossing a bridge when it got wet due to a rogue wave.
3.The robot is working on a live power line when suddenly it broke and came in
contact with the metal part of the robot.
10
What I Can Do
Materials needed:
-Copper wire, 24 inches long and 20-26 standard wire gauge(swg)
-Large paper clips, metallic (2pcs.)
-Battery, size D or C
-Tape (electric or masking)
-Magnet, ¼ inch (0.6 cm) diameter
-Sandpaper, fine-grit
-Cap of a large felt-tip marker or any cylinder, ½ inch (1.3 cm) in diameter
-Wire cutter
11
Prepping the copper wire….
STEP 1: From one end of the copper wire, measure about 1.6 inches (4 cm), and
from that point onward, wind the copper wire twelve (12) times around the
marker cap. Cut the magnet wire with the scissors, leaving about 1.6
inches (4 cm) free (uncoiled) at each end.
The copper wire must be neatly and evenly coiled. If it is not, the weight may
not be evenly distributed, making it difficult for the electromagnet coil to rotate in
the final motor setup. Make sure the loops are touching each other, always parallel
to one another.
STEP 2: Thread each free end of the copper wire through the coil’s loops in the 3
o'clock and 9 o'clock positions, as shown. (like in a clock hand)
Note:
12
electrical contact between the axle and the axle support (In this case, the large
paper clips).
STEP 3: Fold sandpaper in half. Be sure to make the rough sides facing each other,
to make a "sandpaper sandwich." Strip the insulation of one end of the
copper wire by putting the end inside the sandpaper sandwich. Press the
sandpaper sandwich and gently rub it over the wire back and forth to
remove the coating on all sides of the wire. The wire is stripped when you
can see the copper wire end turn pale in color.
STEP 4: Using the sandpaper sandwich, strip ONLY the top half of the insulation
off the end of the copper wire. Place one end of the wire on a piece of
cardboard (to protect the table underneath) at the edge of a table. Hold the
copper coil in an upright position and gently rub the sandpaper over the
wire to remove the top half of the insulating material from the wire.
13
Figure 12: Stripped ends of a copper wire coil.
Note:
After removing the enamel coating, the ends of your copper wire coil should
look like this, as shown in the figure above.
STEP 5: Bend the inner part of each of your two paperclips open to create the
structure, as shown below. To do this, gently lift the shorter end of the
paperclip and slowly move it upward (like a clock hand), counterclockwise
over the longer piece, until it reaches the 12 o'clock position, with the
original longer section still in the 6 o'clock position. The paperclip should
now look like an elongated number 3 with a tiny, more or less circular,
hole in the middle.
A B C D E
14
STEP 6: Secure the paperclip to the positive end (longer end) of the battery with
tape to build the axle support. The arrow indicates it is about to be folded
over to cover the paperclip and battery top. Check that the electrical
contact is created between the battery and the axle support (paperclip).
15
Source:https://rb.gy/r3yupz
STEP 8: While the battery is balanced between the pages of an open booklet and
the attached axle supports are facing upward, place the magnet at the top
center of the battery halfway between the paperclips. Insert each axle end
(copper coil end) into the small loop of the axle support. The copper coil
should be spinning to indicate that your electric motor is running.
16
Guide Questions:
Your improvised electric motor will be scored using the rubric below.
Indicator 5 4 3 2
Materials Used of the Failed use one Failed to use Failed to use
used materials (1) of two (2) three (3)
required. materials materials materials
required required required
Motor The coil The coil The coil The coil did
Efficiency needed to needed to be needed to be not spin.
be spun spun 3x spun 6x
once before before it before it
it started started started
spinning. spinning. spinning.
17
Assessment
Directions: Read each question carefully. Choose the letter of the correct answer.
1. Which of the following measures how much force a motor can produce or exert?
a. speed
b. stator
c. rotor
d. torque
2. What are the name of the stationary part and the spinning component of an
electric motor?
a. commutator and rotor
b. stator and armature
c. terminals and axle
d. magnets and battery
3. Which part converts electrical energy to mechanical energy that enables the
robot
to do work?
a. stator
b. battery
c. motor
d. current
4. Which part of the motor relays the electrical current from the battery to the
commutator?
a. brushes
b. rotor
c. stator
d. magnets
5. What force is induced when a current passes through a copper coil, causing
the motor to run?
a. electropower
b. electromagnetism
c. electrobattery
d. electrocharges
6. What unit is used to count the number of times the axle makes one complete
rotation in a minute?
a. ACM
b. ECM
c. MAS
18
d. RPM
7. Which of the following is NOT a part of an electric motor?
a. alternator
b. armature
c. commutator
d. stator
8. Which of the following parts is found inside the stator of the motor?
a. axle
b. battery
c. copper coils
d. magnets
9. What part of the motor is situated at one end of the coil and is composed of
a metal ring divided into two halves?
a. armature
b. axle
c. battery
d. commutator
10. Which of the following refers to the central shaft of the motor where the
copper
wires are wound?
a. axle
b. battery
c. magnets
d. terminals
19
Additional Activities
Materials needed:
Improvised Electric motor
Copper wire (24 inches and 20-26 swg)
Battery, 3 pcs.
Procedure:
Step 1: Connect all the materials of the motor so that it would be working.
Step 2: When the motor is working correctly, count how many times the coil spun
in one (1) minute. Record your observation in the table below.
Step 3: Repeat step 2 but this time add another battery to the motor. Remember to
make the necessary adjustments to the coil because the battery will make
your motor longer. The copper coil is still wound up twelve (12) times.
When you are done with the construction, set your electric motor again
and count how many times the coil spun for one (1) minute. Record your
observation below.
Step 4: This time add another battery to the setup. Your motor now is connected to
3 batteries. Repeat step 3 and count how many times the coil spun in 1
minute. Record your observation.
1 battery
2 batteries
3 batteries
Guide Questions:
20
1. How many batteries did the copper coil spun the most? Why do you think so?
2. How many batteries did the copper coil spun the least? Why do you think so?
3. In your observation, does adding two (2) or three (3) batteries to our homemade
motor affect the number of times the coil spun? Explain further.
4. Write your conclusion based on your observation?
21