Fosroc Nitoflor FC130 constructive solutions

Water based, epoxy resin floor and wall coating

Uses Specification

To provide a dust-proof easily cleaned surface which is Epoxy floor coating

resistant to most oils and liquids. It is suitable for use on:
The floor coating shall be Nitoflor FC130, a two-component
„ Walls and floors in warehouses. water dispersed epoxy suitable for application by brush or
lambswool roller. The coating shall be applied in two coats to
„ Garages.
achieve a total dry film thickness of approximately 100 microns.
„ Light industrial and food processing areas.
Properties
„ Kitchens and other areas of pedestrian and light vehicular
traffic. The value given below are average figures achieved in
laboratory tests. Actual values obtained on site may show
Advantages minor variations from those quoted.

„ Antibacterial - resists bacterial growth. Physical properties

@ 23°C @ 35°C
„ Durable - good resistance to abrasion.
Pot life* : 4 hours 2 hours
„ Economical - easy to apply, minimises cleaning costs. Time between coats : 6-24 hours 4-16 hours
Initial hardness : 24 hours 16 hours
„ Water based - safe in use, low odour.
Full cure : 7 days 7 days
„ Attractive - available in a range of colours. Dry film thickness (2 coats) : 100 microns (approx.)

„ Good resistance to a wide range of chemicals. *Note: that after the pot life has expired the material, although
not hardened, may not have increased in viscosity
Standard compliance but the characteristics of the product change. Excess
material should be discarded after this point.
Nitoflor FC130 complies with BS476, Part7:1987-Class 1
spread of flame.
Chemical properties
Description
Nitoflor FC130 is resistant to a wide range of chemicals.
Nitoflor FC130 is a two-component water dispersed epoxy Specific data is available on request.
resin coating system supplied in pre-weighed packs ready
Good housekeeping is essential in areas where chemical
for on-site mixing and use.
spillage is likely to occur. It is especially important that such
The cured film forms a hard, semi-matt seal to concrete and spillage should not be allowed to dry since very much higher
other substrates. concentrations of chemicals will then result.

The product is available in a wide range of standard colours

Instructions for use
and is also available in a clear grade.
Surface preparation
Design criteria
It is essential that Nitoflor FC130 is applied to sound, clean
Nitoflor FC130 is designed for application in two coats to substrates in order to achieve maximum adhesion between
achieve an approximate total dry film thickness of 100 microns. the floor coating and substrate.
Substrates should be dry and not suffer, or be likely to suffer,
The substrate must be fairly smooth, as any surface
from rising damp. If necessary, suitable damp-proof
irregularities may show through Nitoflor FC130 changing the
membranes should be installed to prevent this. Substrates
perceived colour of the coating and causing excessive wear
should not have a relative humidity greater than 80% at the
on high spots.
time of installation.
Nitoflor FC130
Fosroc Nitoflor FC130

New concrete floors Good drying conditions are required to allow complete
evaporation of the water as the resin cures. Adequate ventilation
The floor should be typically at least 28 days old and give a
and air movement is necessary.
hygrometer reading not exceeding 80% RH when tested in
accordance with BS 8203 Appendix A. For application at earlier Cleaning
stages contact your local Fosroc office for further advice. Dry
Nitoflor FC130 should be removed from tools and equipment
removal of laitance by light grit blasting is preferable. Dust
with clean water immediately after use. Nitocote RI should be
and other debris should then be removed by vacuum brush.
removed from tools and equipment using Fosroc
Old concrete floors Solvent 102*. Hardened material can only be removed
mechanically.
A sound, clean substrate is essential to achieve maximum
adhesion. Light grit blasting should be carried out as for new Maintenance
concrete floors. Oil and grease penetration should be removed
The service life of a floor can be considerably extended by
by hot compressed air treatment and primed with a single
good housekeeping practices. Regular cleaning of Nitoflor FC130
coat of Nitocote RI*†.
may be carried out using a rotary scrubbing machine with a
Epoxy screeds water miscible cleaning agent or by hot water washing at
temperatures up to 50°C.
Nitoflor FC130 may be applied to Fosroc epoxy resin screeds.
High spots or trowel marks should be rubbed down and dust
Limitations
and other debris removed by vacuum cleaning.
- Nitoflor FC130 should not be applied on to surfaces known
Asphalt floors
to, or likely to suffer from, rising damp or have a relative
When used to coat asphalt floors, under these circumstances humidity greater than 75% as measured in accordance with
Nitoflor FC130 can be applied to asphalt floors provided they BS 8203 Appendix A, or by a Hammond concrete/mortar
are at least 12 months old. moisture tester type COCO.

When used as a primer for joints in asphalt substrate before - The durability of Nitoflor FC130 in foot traffic areas is
the application of Colpor 200PF; asphalt should be at least 4 reduced in areas of very heavy traffic such as around work
months old, contact your local Fosroc office for further advise. benches, drinks machines etc. It is advisable to either:

Mixing a) specify additional coats in such areas or,

The individual components of Nitoflor FC130 should be b) specify a higher build system from Fosroc flooring
thoroughly stirred before the two are mixed together. The entire range.
contents of the base container should be poured into the
- Nitoflor FC130 should not be applied at temperatures
hardener container and the two materials mixed thoroughly
below 10°C or where ambient relative humidity exceeds
for at least 3 minutes. The use of a heavy duty slow speed drill
85%.
fitted with a Fosroc Mixing Paddle (MR3) is desirable.

Coating Technical support

The mixed Nitoflor FC130 should be applied to the prepared Fosroc offers a comprehensive range of high performance,
surface using a brush or lambswool roller. Ensure that the high quality flooring, jointing and repair products for both new
area is completely coated and that ‘ponding’ of the material and existing floor surfaces. In addition, the company offers a
does not occur since water may be trapped within the product, comprehensive technical support service to specifiers, end
thus preventing complete cure. users and contractors. It is also able to offer on-site technical
assistance, an AutoCAD facility and dedicated specification
The second coat may be applied as soon as the first coat has
assistance in locations all over the world.
initially dried (typically 12-18 hours). The time will be dependent
on the type of surface and the ambient conditions. If the
overcoating window is missed the first coat must be abraded
with a medium sand paper before application of the second
coat.

Nitoflor FC130 - Page 2 of 4

Fosroc Nitoflor FC130

Estimating Precautions

Supply Health and safety

Nitoflor FC130 : 4.5 litre packs
Nitoflor FC130, Nitocote RI and Fosroc Solvent 102 should
Nitocote RI : 4.5 litre packs
not come in contact with the skin and eyes, or be swallowed.
Fosroc Solvent 102 : 5 litre drums
Ensure adequate ventilation and avoid inhalation of vapours.
Coverage Some people are sensitive to resins, hardeners and solvents.
Nitoflor FC130 : 10.0 m2/litre Wear suitable protective clothing, gloves and eye protection.
@ 100 microns wft/coat If working in confined areas, suitable respiratory protective
Nitocote RI : substrate dependent equipment must be used. The use of barrier creams provide
additional skin protection. In case of contact with eyes, rinse
The coverage figures given are theoretical - due to wastage immediately with plenty of clean water and seek medical
factors and the variety and nature of possible substrates, attention immediately - if swallowed seek medical attention
practical coverage figures will be reduced. immediately - do not induce vomiting.

Storage Fire

Shelf life Nitoflor FC130 and Nitocote RI are non-flammable.

All products have a shelf life of 12 months if kept in a dry store Fosroc Solvent 102 is flammable. Keep away from sources
in the original, unopened packs. of ignition. No smoking. In the event of fire, extinguish with
CO2 or foam. Do not use a water jet.
Storage conditions
Flash points
Store in dry conditions between 10°C and 30°C, away from
Fosroc Solvent 102 : 33°C
sources of heat and naked flames in the original, unopened
packs. If stored at high temperatures the shelf life may be Disposal
reduced.
Spillages of component products should be absorbed on to
earth, sand or other inert material and transferred to a suitable
vessel. Disposal of such spillages or empty packaging should
be in accordance with local waste disposal regulation.

For further information, refer to the Product Material Safety

Data Sheet.

Nitoflor FC130 - Page 3 of 4

Fosroc Nitoflor FC130

Additional Information

Fosroc manufactures a wide range of products specifically

designed for the specialist flooring industry. These include:

„ liquid-applied

„ chemically-resistant coatings

„ self-levelling epoxy toppings and

„ trowel-applied, highly abrasion-resistant screeds.

Among them are products suitable for use in:

„ the food and drinks industry

„ the pharmaceutical industry and

„ in areas subjected to heavy industrial use.

Where the control of static electricity is an important

consideration, Fosroc have developed conductive and
dissipative seamless floor systems. In addition, a wide range
of complementary products is available. This includes joint
sealants, waterstops, waterproofing membranes and
specialised products for the repair and refurbishment of
damaged reinforced concrete.

For further information about products or publications, contact

the local Fosroc office.

* Denotes the trademark of Fosroc International Limited

†
See separate data sheet

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for
the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to
obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
United Arab Emirates Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com

www.fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
Qatar, Tadmur telephone: 4432365 fax: 4419517 email: qatar@fosroc.com

UAE/0294/11/E