Nitoflor FC150*

Solvent free, high build , epoxy resin floor

coating

Uses Specification

Nitoflor FC150 provides a hard wearing, chemical and abrasion The epoxy resin floor coating shall be Nitoflor FC150 from
resistant floor finish. It is ideally suited for use in wet areas Fosroc. The total dry film thickness of the coating shall be a
where a high degree of resistance to chemicals, oils and minimum of 400 microns and shall have a compressive
grease is required such as : strength of 70 N/mm2, flexural strength of 40 N/mm2 and a
tensile strength of 20 N/mm2. The floor shall be prepared and
Dairies
the coating mixed and applied in accordance with the
Soft drinks production facilities manufacturer's current data sheet.

Chemical manufacturing plants

Design criteria
Car parks and workshops
Nitoflor FC150 is applied as a floor coating system comprising
of two top coats (depending on the substrate conditions a
Advantages
primer might be required), each top coat to be a minimum of
Durable, low maintenance costs. 200 microns thick. To provide a slip resistant texture, the first
top coat can be dressed with Nitoflor Antislip Grains*.
Proven against a wide range of industrial chemicals.

Solvent free - no odour during application. Properties

Slip resistant - different textures available to suit conditions The following values were obtained when tested at 20C and
to avoid slipping. 30C.

Liquid applied providing complete protection. @ 20C @ 30C

Available in a wide range of colours to improve the working Pot life : 40 mins 20 mins
environment and identify slip hazard areas. Cure time : 24 hours 18 hours
Maximum time
Specially formulated for use in Middle East conditions. between coats : 36 hours 15 hours
Light traffic use after : 24 hours 18 hours
Description
Full traffic use after : 48 hours 24 hours
Nitoflor FC150 is a solvent free system based on epoxy resins Resistance to
and curing agents specially selected for their ability to chemical spillage : 7 days 5 days
withstand chemical attack. The system consists of pre- Compressive strength : 70 N/mm2
weighed base & hardener components and a Nitoflor colour Flexural strength : 40 N/mm2
pack, all of which contain reactive elements that are essential Tensile strength : 20 N/mm2
to the installation of the system. Water absorption : 0.06%
(ASTM C 413:1996)
A slip resistant texture can be provided by the use of one of a Shore D Hardness : 85
range of Nitoflor Antislip Grains which have been carefully (ASTM D 2240 : 1996)
graded to ensure an even texture.
Nitoflor FC150
Chemical resistance Old concrete floors

Fully cured Nitoflor FC150 samples have been tested in a wide A sound, clean substrate is essential to achieve maximum
range of aggressive chemicals commonly found in industrial adhesion. As for new concrete floors dry removal of laitance
environments. Tests were performed in accordance to ASTM by use of mechanical methods is preferable. Oil and grease
D 543 standards over 168 hours (7 days) at 23C+2) penetration should be removed by the use of a proprietary
chemical degreaser or by hot compressed air treatment.
Acids
Lactic acid 10% : Resistant Any damaged areas or surface irregularities should be repaired
Citric acid 10% : Resistant using one of the Nitoflor EU* range products.
Acetic acid 10% : Resistant
Priming
Hydrochloric acid 50% : Resistant
Sulphuric acid 50% : Resistant Priming is not normally required provided the substrate is
Nitric acid 25% : Resistant sound, untreated and good quality nonporous concrete. If
any doubts exist of the quality of the concrete, or if it is porous
Alkalis
it should be primed with Nitoprime SP*. Contact the local
Sodium hydroxide 50% : Resistant Fosroc office for advice.
Ammonia (0.880) 10% : Resistant
Nitoprime SP should be mixed in the proportions supplied.
Solvents Add the entire contents of the hardener can to the base can.
Petrol : Resistant When thoroughly mixed, preferably using a slow speed drill
Oil : Resistant and paddle, the primer should be applied in a thin continuous
Kerosene : Resistant film, using rollers or stiff brushes. Work the primer well into
Butanol : Resistant the surface of the concrete taking care to avoid ponding or
Skydrol : Resistant over application.
Industrial Methylated spirits : Resistant
The primer should be left to achieve a tack-free condition
Others before applying the top coat. A second coat of primer may
Saturated sugar solution : Resistant be required if the substrate is excessively porous.
Urea (saturated) : Resistant
Mixing the coating
Bleach 5% : Resistant
The base and hardener components of Nitoflor FC150 should
All the above properties have been determined by laboratory
be thoroughly stirred before the two are mixed together. The
controlled tests and are in excess of those expected in
entire contents of the hardener container should be poured
practice.
into the base container and the two materials mixed thoroughly,
Nevertheless, success in use will be determined by the then add the colour pot and mix for at least 3 minutes. The
implementation of good housekeeping practices. use of a heavy-duty slow speed, flameproof or air driven drill
fitted with a Fosroc Mixing Paddle (MR3) is desirable. Mix
Instructions for use these components in the quantities supplied taking care to
ensure all containers are scraped clean. Do not add solvent
Surface preparation
thinners at any time.
The long term durability of any resin floor system is determined
Standard application
by the adhesive bond achieved between the flooring material
and the substrate. It is most important therefore that The first coat of Nitoflor FC150 should be applied using a
substrates are correctly prepared prior to application. good quality medium haired pile roller, suitable for epoxy
application, or squeegee to achieve a continuous coating.
New concrete floors
Ensure that loose hairs on the roller are removed before use.
These should normally have been placed for at least 28 days A minimum film thickness of 200 microns should be applied.
and have a moisture content of less than 5%. Floors should This can be increased where specifications demand.
be sound and free from contamination such as oil and grease,
When the base coat has reached initial cure (12 hours @ 20C
mortar and paint splashes or curing compound residues.
or 5 hours at 35C). The top coat can be applied by medium
Excessive laitence can be removed by the use of mechanical
haired roller, at minimum film thickness of 200 microns. Care
methods. Dust and other debris should then be removed by
should be taken to ensure that a continuous film is achieved.
vacuum cleaning.
Nitoflor FC150 - Page 2 of 4
Antislip application Technical support

If a slip resistant texture is required, the base coat shall be Fosroc offers a comprehensive technical support service to
applied as per the standard application, but at a minimum specifiers, end users and contractors. It is also able to offer
film thickness of 250 microns. The base coat should then be on-site technical assistance, an AutoCAD facility and
dressed with the chosen Nitoflor Antislip Grain. This should dedicated specification assistance in locations all over the
be done as soon as possible after laying. The recommended world.
procedure is to completely blind the base coat i.e. apply excess
dressing aggregate to completely obliterate the base coating. Estimating

Alternatively, the Nitoflor Antislip Grains can be broadcast in Supply

a light random dressing to provide a less dense finish. Nitoprime SP : 4 litre packs
Nitoflor FC150
When the base coat has reached initial cure (12 hours @ 20C
(Including colour pack) : 4.5 litre packs
or 5 hours at 35C), the excess aggregate should be vacuum
Nitoflor Antislip Grains : 20 kg bags
cleaned from the surface.
Fosroc Solvent 102 : 5 litre cans
The top coat can now be applied by medium haired roller, at a
rate of 4.0m2/litre. Care should be taken to ensure that a Standard coverage
continuous film is achieved and the rough surface, caused by Nitoprime SP : 8m2/litre
the aggregate, is completely sealed. This top coat must be Nitoflor FC150 (base coat) : 5.0m2/litre @
applied within 36 hours @ 20C (15 hours @ 35C) of the 200 microns wft
application of the first coat. Nitoflor FC150 (top coat) : 5.0m2/litre @
Expansion joints 200 microns wft

Expansion joints in the existing substrate must be retained Coverage - Antislip (approx.)
and continued through the Nitoflor FC150 topping. Fosroc (for medium texture)
have a range of joint sealants specifically designed for flooring, Nitoprime SP : 8m/litre
contact local Fosroc office for advice. Nitoflor FC150 (base coat) : 4.0m2/litre @
Cleaning 250 microns wft
Antislip Grain No 2* : 1.25-3m2/kg
Tools and equipment should be cleaned with Fosroc Solvent Nitoflor FC150 (top coat) : 4.0m2/litre
102* immediately after use. Spillages should be absorbed Estimated system thickness : 1.5 - 2.0mm
with sand or sawdust and disposed of in accordance with
local regulations. (for fine texture)
Nitoprime SP : 8m/litre
Limitations Nitoflor FC150 (base coat) : 4.0m2/litre @
- Nitoflor FC150 should not be applied on to surfaces known 250 microns wft
to, or likely to suffer from, rising dampness, potential osmosis Antislip Grain No 3* : 1.25 - 3.5m2/kg
problems or have a relative humidity greater than 75% as Nitoflor FC150 (top coat) : 4.0m2/litre
measured in accordance with BS 8203 Appendix A, or by a Estimated system thickness : 0.75 - 1.5mm
Hammond concrete/mortar moisture tester type COCO. * Depending on the type of texture required.
- Fosroc does not recommend acid etching as a method of Note: Coverage figures given are theoretical - due to wastage
floor preparation. If used, the method should be approved factors and the variety and nature of substrates,
by the project consultant. practical coverage figures may be reduced, this will
- In common with all epoxy materials, some slight shade vary with site and application conditions.
changes may be experienced over the long term when
placed in adverse exposure conditions. Any such change
in shade is not regarded as being detremental to
performance.

Nitoflor FC150 - Page 3 of 4

Storage Fire

Shelf life Nitoprime SP and Fosroc Solvent 102 are flammable. Do not
expose to naked flames or other source of ignition. No smoking
Nitoflor FC150 has a shelf life of 12 months when stored in
during use. Containers should be tightly sealed when not in
warehouse conditions below 35C in the original, unopened
use. In the event of a fire, extinguish with CO2 or foam.
packs.
Flash points
Storage conditions
Nitoprime SP : 57C
Store under warehouse conditions, below 35C in the original, Fosroc Solvent 102 : 33C
unopened packs. For further information, refer to the product Material Safety
Data Sheet.
For further information, refer to the Product Material Safety
Data Sheet. Additional Information

Cleaning and disposal Fosroc manufactures a wide range of complementary products

which include :
Spillages of component products should be absorbed on to
earth, sand or other inert material and transferred to a suitable waterproofing membranes & waterstops
vessel. Disposal of such spillages or empty packing should
joint sealants & filler boards
be in accordance with local waste disposal regulations.
cementitious & epoxy grouts
Precautions
specialised flooring materials
Health and safety
Fosroc additionally offers a comprehensive package of
Nitoflor FC150, Nitoprime SP and Fosroc Solvent 102 should products specifically designed for the repair and refurbishment
not come in contact with skin and eyes or be swallowed. Avoid of damaged concrete. Fosrocs Systematic Approach to
prolonged inhalation of solvent vapours. concrete repair features the following :

Some people are sensitive to epoxy resins, hardeners and hand-placed repair mortars
solvents. Gloves, goggles and a barrier cream such as
spray grade repair mortars
Kerodex Antisolvent or Rozalex Antipaint should be used.
Ensure adequate ventilation and if working in enclosed areas, fluid micro-concretes
use suitable breathing apparatus.
chemically resistant epoxy mortars
If mixed resin comes into contact with the skin, it must be
anti-carbonation/anti-chloride protective coatings
removed before it hardens with a resin removing cream such
as Kerocleanse Standard Grade Skin Cleanser or Rozaklens chemical and abrasion resistant coatings
Industrial Skin Cleanser, followed by washing with soap.
For further information on any of the above, please consult
Should accidental eye contamination occur, wash well with your local Fosroc office - as below.
plenty of clean water and seek medical advice. If swallowed,
seek medical attention immediately. Do not induce vomiting. * Denotes the trademark of Fosroc International Limited

See separate data sheet

Al Gurg Fosroc LLC REGIONAL SALES OFFICES IN :

P. O. Box 657 DUBAI ABU DHABI BAHRAIN KUWAIT OMAN QATAR
Dubai Al Gurg Fosroc Al Gurg Fosroc YBA Kanoo Boodai GETCO Tadmur
United Arab Emirates

TEL : (04) 285 8606

TEL : 285 8787 TEL : 673 1779 TEL : 738200 TEL : 481 7618 TEL : 771 5080 TEL : 441 3628
FAX : (04) 285 9649 FAX : 285 2023 FAX : 673 1449 FAX : 732828 FAX : 483 2124 FAX : 771 7554 FAX : 444 0812

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard terms and conditions of sale, copies of
which may be obtained on request. Whilst Fosroc endeavours to ensure that the technical information on this data sheet is correct at the time of printing, it
is the customers responsibility to satisfy himself, by checking with the company that this information is still current at the time of use, that the product is
suitable for the intended application, and that the actual conditions of use are in accordance with those recommended. Because Fosroc has no control over
the conditions of use of its products, all recommendations or suggestions regarding the use of these products are made without guarantee.

UAE/0079/01/G
www.fosrocgulf.com