02

18
Quality Products for Mechanical
& Fluid Power

SCREW PUMPS
 an excellence in engineering

The comprehensive service for the

mechanical power transmission & fluid power industries.

Screw Pump Applications

This catalogue has a marine bias at present with industrial, and oil & gas to follow in the near future. Many of these
screw pump models serve industrial, oil & gas and marine applications. Please check periodically for updates that include
industrial and oil & gas sectors, as well as further models not currently listed.

STRIPPING: Twin-screw pumps with and without drive gears FEEDER: Pumps, double booster systems and flow meter
for filling and emptying tanks for various types of fluids of systems developed for use with low viscosity fluids with low
various compositions. Great availability of flow rates. sulphur content, in keeping with environment and emissions
standards, designed to be long-lasting with reduced
CARGO: Pumps for filling Terminal Silos, the tanks of ships maintenance costs. The entire range is implemented with
equipped for transporting fluids, in addition to the main assembled motor - pump units with MAGNETIC DRIVE.
storage tanks for propulsion fuel fluids. Low-pressure medium
and high flow rates with a vast range of treatable fluids and BOILER/BURNER: Pumps and double booster systems for
viscosities. low viscosity, low and medium pressure fuel fluids, for boilers
and burners.
TRANSFER: Fluid transfer systems from main tanks to daily
tanks. Low-pressure medium and high flow rates with a vast LUBE: 40 years of experience and success in fluid power,
range of treatable fluids and viscosities. lubrication systems, including adverse environmental
conditions in addition to temperatures and viscosities. A broad
SEPARATOR: Pumps, double booster systems and flow range of pumps are available for any plant engineering
meter systems developed for use with low viscosity fluids with requirement.
low sulphur content, in keeping with environment and
emissions standards, designed to be long-lasting with HYDRAULIC: High efficiency and stability for medium
reduced maintenance costs. The entire range is implemented pressure up to 120 bar, for the following types of hydraulic
with assembled motor - pump units with MAGNETIC DRIVE. systems: Propeller and Steering Gear.

quality products for mechanical & fluid power

01737 767493 info@jbj.co.uk www.jbj.co.uk

jbj Techniques Limited is ISO certificated,
A range of products ATEX certificated
committed to international coordination - registered in England No: 1185469 -
to directive 94/9/E requirements
& unification of industrial standards.

jbj Techniques is a specialist manufacturer and distributor of high quality products for the mechanical power transmission & fluid power sectors. You
Tube
Screw Pumps Contents

SCREW PUMPS

The details contained within this catalogue are reproduced in accordance with the latest information at going to press ................................. E & OE

Page

Application Pump Types ...................................................................1 -2

PB Series ........................................................................................................3 -4

PHS Series .....................................................................................................5 -6

PZ Series .........................................................................................................7 -9

PZD Series .....................................................................................................10 - 11

PXF Series .....................................................................................................12 - 14

PO - PWO Series ......................................................................................15 - 16

POF - PWOF Series ................................................................................17 - 18

2SP LS Series .............................................................................................19 - 20

2SP Series ......................................................................................................21 - 24

MPV2 Series .................................................................................................25 - 26

PDP Series .....................................................................................................27 - 28

SPB Series .....................................................................................................29 - 30

Magnetic Coupling Drive ..................................................................31

Product Range Performance Chart .........................................32

Screw Pumps Application Pump Types

SCREW PUMPS

Three Screw Pumps Three Screw Pumps

Low Pressure Medium Pressure
COMPONENT TYPE
PB PHS PZ PZD PXF PO - PWO POF - PWOF

COMPONENT MODEL

Main Characteristics

Flow Rate Up To M3/h (lpm) 2.5 (41) 12 (200) 288 (4.800) 600 (10.000) 288 (4.800) 34 (560) 34 (560)

Max Operating Pressure (bar) 16 16 16 16 30 40 120

Typical Viscosity (Cst) 1.2 - 5.000 1.2 - 5.000 1.2 - 5.000 1.6 - 5.000 10 - 5.000 1 - 15 10 - 5.000

Max Operating Temperature (°C) 150 150 150 120 120 120 120

Typical Applications

Stripping

Cargo

Transfer

Separator

Feeder

Circulating

Boiler / Burner

Lube: Diesel Engine, Thruster, Gear Box

Hydraulic *

Typical Fluids

Fuel Oil: HFO - LFO - MGO - DO - LSMGO

Mineral Oil / Lube Oil

GG25 GG25 GG25

Body Materials GGG40 GGG40 d
Q
M Al
GGG40 C.S. GGG40

Screw Set Materials Nitrided Steel Nitrided Steel Nitrided Steel Nitrided Steel Carbon Steel Nitrided Steel Nitrided Steel

Mechanical Seal

Magnetic Coupling

Integrated Relief Valve

Standard In / Out
DIN PN16 DIN PN16 SAE 3,000psi
SAE 3,000psi Special SAE 3,000psi SAE 3,000psi
Port Connection ANSI option ANSI option DIN***PN16

*Deck Machinery, Pitch Propeller, Steering Gear, Door and Ramp. **Depends from valve model and size. *** Up to size 083: SAE 3.000psi port / from size

1
 Screw Pumps Application Pump Types

SCREW PUMPS

Twin Screw Pumps Double Station Consumption

Low Pressure Low Pressure & Control

2SP LS 2SP PDP SPB MPV2 VMP/BVPA

600 (10.000) 1200 (20.000) 12 (200) 2.5 (41) 420 (7.000) 72 (1.200)**

16/40 16/40 16 16/40 40/200 150**

0.7 - 5.000 0.7 - 5.000 1.2 - 5.000 1.2 - 5.000 1 - 5.000 10 - 5.000**

300 300 150 150 150 100

C.S. C.S. C.S.

GGG40 GGG40 GG25
GGG40 GGG40 GGG40

Nitrided Steel Nitrided Steel Nitrided Steel Nitrided Steel Nitrided Steel -

N.A. N.A.

N.A. N.A.

option option kK
^ N.A.

DIN DIN SAE 3,000psi

1½” ANSI 150 DN32 PN16/40 SAE 3,000psi
ANSI option ANSI option DN PN

e 083 to 156: DIN flange.

2
Screw Pumps PB Series Technical Specifications

SCREW PUMPS

For hydraulic oils, lubricating oils.

Special version for heavy fuel.

Allowable delivery pressure (continuous) up to 16 bar from 1000 to 3600 rpm (viscosity < 10 cSt) or up to 40 bar (> 10 cSt)

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Transfer, fuel supply, lubricating, boiler.

Operating Data
Handled fluid Fuel oil HFO - DO - LSMG0 - Hydraulic and Lube oils.
Viscosity range From 1,2 to 5000 cSt.
Pump speed From 750 to 3600 rpm *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 41 LPM - 2,5 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 40 bar (from 1000 to 3600 rpm).
Operating temperature range From 0 to 150 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication Lubricated for life.
Mounting arrangement Horizontal or vertical mounting.
Inlet & Outlet connection Special version.

Materials
Casing/Flanges Modular cast Iron GGG40.
Screws Nitrided steel.
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

3
Screw Pumps PB Series Technical Specifications

SCREW PUMPS

E Ød4

G
F

N P
Ød2

I1
shaft detail
K Ød3
J

M L
d1

C B H

I2
Dimensions in mm unless otherwise stated.

in out

Model A B C D E F G H I1 I2 J K L M N O P d1 d2 d3 d4
SAE SAE Gas Gas Ø Ø Ø Ø
3000 3000

PB020-025 318 65 67 29 16 5 45 151 115 111 16 5 1" 1" 1/8" 1/8" 93 14 100 11 125

4
Screw Pumps PHS Series Technical Specifications

SCREW PUMPS

For hydraulic oils, lubricating oils.

Special version for heavy fuel.

Allowable delivery pressure (continuous) up to 16 bar from 1000 to 3600 rpm

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Separator, transfer, booster, feeder, fuel supply, lubricating.

Operating Data
Handled fluid Fuel oil HFO - DO - LSMG0 - Hydraulic and Lube oils.
Viscosity range From 1,2 to 5000 cSt.
Pump speed From 750 to 3600 rpm *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 200 LPM - 12 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 16 bar (from 1000 to 3600 rpm).
Operating temperature range From 0 to 150 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication Lubricated for life.
Mounting arrangement Horizontal or vertical mounting.
Inlet & Outlet connection Special version.

Materials
Casing/Flanges Modular cast Iron GGG40.
Screws Nitrided steel.
O-rings Viton ®.
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

5
Screw Pumps PHS Series Technical Specifications

SCREW PUMPS

shaft detail

Dimensions in mm unless otherwise stated.

in out

Model A B C D E F EF G H L M T V d1 d2 d3 d6 l1 l2 l12 l O1 O2 O12 O

Ø Ø Ø Ø Ø Ø Ø Ø Ø
PHS025 274 60 50 29 61.5 63.6 9 1/8" 73 60 68 16 5 14 110 130 9 62 28 9 25 62 28 9 25
PHS032 288 68 50 29 61.5 63.6 9 1/8" 73 75 68 16 5 14 110 130 9 90 40 11 40 62 28 9 25
PHS040 297 75 50 34 61.5 72 9 1/8" 83 85 75 21.5 6 19 120 145 11 90 40 11 40 90 40 11 40

6
Screw Pumps PZ Series Technical Specifications

SCREW PUMPS

For hydraulic oils, lubricating oils.

Special version for heavy fuel.

Allowable delivery pressure (continuous) up to 16 bar from 1000 to 3600 rpm (vertical arrangement)
Allowable delivery pressure (continuous) up to 16 bar from 750 to 1800 rpm (horizontal arrangement)

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Cargo, separator, Transfer, Booster, Feeder, Fuel supply, Lubricating.

Operating Data
Handled fluid Fuel oil HFO - DO - LSMG0 - Hydraulic and Lube oils.
Viscosity range From 1,2 to 5000 cSt (specific configuration may apply).
Pump speed From 750 to 3600 rpm *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 4800 LPM - 288 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 16 bar (from 1000 to 3600 rpm).
Operating temperature range From 0 to 150 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication Lubricated for life.
Mounting arrangement Horizontal or vertical mounting (foot on demand).
Inlet & Outlet connection DIN standard (ANSI on demand).

Materials
Casing/Flanges Cast Iron GG25 or GGG40.
Screws Nitrided steel.
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

7
Screw Pumps PZ Series Technical Specifications

SCREW PUMPS

P
PZ 032 ONLY
IN
ØI Q

G
C
S
G2

61,5
OUT O
D E 63,6 Ø9

OPTION
FLANGE IN-OUT B MOTOR FLANGE
A

45°
032-040
045
M
N

032
L

G1

45°
N°2 M16 H 040-045
055-060

055-060 R1 072

072 W
OPTION

Shaft detail
I3

I2
I1 k6

Dimensions in mm unless otherwise stated.

Model A B C D E F G G1 G2 H I I1 I2 I3 L M N O P Q R R1 S W
110 14 DN32
PZ032#3 182 288 150 // // 111 16 9 // 130 16 5 100 // 50 12 29 // // // 6
(h7) (k6) PN16
PZ040#3 100 19 DN50
194 353 220 // // 160 18 11 // 125 21.5 6 125 165 41 14 30 250 112 // 9
PZ045#3 (h7) (k6) PN16
PZ055#3 125 28 DN80
237 519 250 200 137 200 18 14 92.5 160 31 8 160 200 52 16 40 350 188 40 9
PZ060#3 (h7) (k6) PN16
160 32 DN100
PZ072#3 270 561 270 200 170 234 18 18 105 200 35 10 180 220 49 15 42 350 200 40 5
(h7) (k6) PN16

8
Screw Pumps PZ Series Technical Specifications

SCREW PUMPS

IN P O
W
Shaft detail
G2
I3 Q

G
C

S
F
I2

I1 k6

I D E
OUT

Option
B
MOTOR FLANGE FLANGE IN-OUT A
083
102 G1

H
126
156

R1
L
M
N R
Option

Dimensions in mm unless otherwise stated.

Model A B C D E F G G1 G2 H I I1 I2 I3 L M N O P Q R R1 S W
DN150
PZ083#3 224 42 PN16
23
415 750 420 350 200 320 23.5 22 128 280 45 12 6" ANSI 240 285 70 59 440 310 120 6
PZ102#3 (h7) (k6) 150 28
PZ126#3 972 340 50 DN250 30 6
570 620 445 275 470 25 26 197 420 53.5 14 355 406 110 97 544 400 150
PZ156#3 1001 (h7) (k6) PN16 33 6.5

9
Screw Pumps PZD Series Technical Specifications

SCREW PUMPS

For hydraulic oils, lubricating oils.

Special version available for heavy fuel oils.

Allowable delivery pressure (continuous) up to 16 bar from 750 to 1800 rpm

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Cargo, transfer, lubricating.

Operating Data
Handled fluid Fuel oil HFO - DO - LSMG0 - Hydraulic and Lube oils.
Viscosity range From 1,2 to 5000 cSt (specific configuration may apply).
Pump speed From 750 to 1750 rpm *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 10.000 LPM - 600 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 16 bar (from 1000 to 1750 rpm).
Operating temperature range From 0 to 150 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication Lubricated for life.
Mounting arrangement Horizontal or vertical mounting (foot on demand).
Inlet & Outlet connection DIN standard (ANSI on demand).

Materials
Casing/Flanges Cast Iron GGG40.
Screws Nitrided steel.
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

10
Screw Pumps PZD Series Technical Specifications

SCREW PUMPS

Dimensions in mm unless otherwise stated.

Model A B C D E F G H I J K K1 L L1 M N O P Q R S T T1 V
DN300 DN250 50
PZD156 1050 530 390 169 50 335 480 160 400 M20 355 M24 480 405 700 54 16 450 530 M16 650
PN16 PN16 (k6)

11
Screw Pumps PXF Series Technical Specifications

SCREW PUMPS

For hydraulic oils, lubricating oils.

Admissible delivery pressure (continuous) up to 30 bar at 1800 rpm.

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Lubrication.

Operating Data
Handled fluid Hydraulic and Lube oils.
Viscosity range From 10 to 5000 cSt *
Pump speed From 750 to 3600 rpm *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 4800 LPM - 288 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 30 bar (from 102 to 156 up to 16 bar).
Operating temperature range From 0 to 120 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication By pumped fluid.
Mounting arrangement Horizontal or vertical mounting (foot on demand).
Inlet & Outlet connection SAE up to size 083, DIN from size 102 to 156.

Materials
Casing/Flanges Cast Iron GG25 (standard), carbon steel on demand.
Screws Nitrided steel.
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

12
Screw Pumps PXF - PXFE083 Series Technical Specifications

SCREW PUMPS

Dimensions in mm unless otherwise stated.

SAE 3000
Model A A1 B C D E F H L L1 M IN OUT T V d1 d2 d3 d4 d5 d6 y
PXF032#4 419 364 88 75 40 5 15 52 211 201 60 2" 1½" 21.5 6 19 125 160 145 120 13 45
PXF040#4 448 393 88 75 40 5 15 52 240 230 60 2" 1½" 21.5 6 19 125 160 145 120 13 45
PXF045#4 494 432 91.5 81 45 5 15 48.5 269 259 75.5 2½" 2" 35 10 32 125 160 145 138 13 50
PXF055#4 534 472 91.5 82 45 5 15 48.5 308 298 75.5 2½" 2" 35 10 32 125 160 145 138 13 50
PXF060#4 631 527 88 84 45 5 18 73.5 386 355 100 4" 2½" 35 10 32 160 200 195 174 18 50
PXF072#4 718 613 88 101 58 5 18 73.5 455 424 100 4" 2½" 35 10 32 160 200 195 174 18 50

13
Screw Pumps PXF - PXFE083 Series Technical Specifications

SCREW PUMPS

Dimensions in mm unless otherwise stated.

Model A B C D E F H L N P T V d1 d2 d3 d4 d5 Z J Y W
DN 100 PN 16 DN 125
PXF083#3 632 154 128 80 5 25 77 350 SAE 4 PN16 43 12 40 250 315 365 26 289 13 264 186
DN125 DN 150
(X) PXF102#3 690 170 145 80 5 30 233 375 PN16 PN16 43 12 40 250 315 365 26 327 18 300 178
DN150 DN 150
(X) PXF126#3 808 180.5 143 80 5 30 237 484 PN16 PN16 43 12 40 250 315 365 26 343 18 320 231
DN250 DN 1250
(X) PXF156#3 896 250 186 97 5 39 300 460 PN16 PN16 53.5 14 50 340 420 470 26 - - - -

14
Screw Pumps PO - PWO Series Technical Specifications

SCREW PUMPS

For cooling lubricants with low viscosity

and minimum lubricating properties (min. oil 4%).

Admissible delivery pressure (continuous) 100 bar at 2900 rpm.

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Boiler / burner.

Operating Data
Handled fluid Light fuel oils LFO, LSMGO - heavy fuel oils (HFO).
Viscosity range From 1 to 15 cSt *
Pump speed From 2900 to 3500 rpm. low lubricity fluids *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 650 LPM - 40 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 40 bar.
Operating temperature range From 0 to 120 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication Lubricated for life..
Mounting arrangement Horizontal or vertical (also vertical semi-submerged, thanks to the intermediate flange).
Inlet & Outlet connection Suction port: BSP thread - Delivery port: SAE 3000.

Materials
Casing/Flanges Cast Iron Gg25, GGG-40 on request *
Screws Nitrided steel *
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

15
Screw Pumps PO - PWO Series Technical Specifications

SCREW PUMPS

Section

Dimensions in mm unless otherwise stated.

Model A B C D E F H I L M IN OUT T V d1 d2 d3 d4 d5 d6 d7 X d8 d9 d10 Z

PWO025 357 67 39 34 3 10 74 219 290 22 1" Gas 1" SAE 21.5 6 19 100 125 120 124 12 140 3 160 150 158 138
PWO025 357 67 39 34 3 10 74 219 290 22 1" Gas 1" SAE 21.5 6 19 100 125 120 124 12 140 3 160 150 158 138
PWO032 400 67 39 34 3 10 74 262 333 22 1" Gas 1" SAE 21.5 6 19 100 125 120 124 12 140 3 160 150 158 138
PWO040 484 102 49 40 7 15 81 312 383 42 1½" Gas 1½" SAE 27 6 22 125 160 154 158 14 180 6 215 203 211 173
PWO045 534 102 49 40 7 15 81 362 433 42 1½" Gas 1½" SAE 27 8 24 125 160 154 158 14 180 6 215 203 211 173
PWO055 613 161.5 64 55 8 15 100 380 451 72 3" Gas 2" SAE 35 10 32 125 160 173 175 14 235 6 265 249 257 232.5
PWO055 667 161.5 64 55 8 15 100 434 505 72 3" Gas 2" SAE 35 10 32 125 160 173 175 14 235 6 265 249 257 232.5

16
Screw Pumps POF-PWOF Series Technical Specifications

SCREW PUMPS

For hydraulic oils, lubricating oils.

Admissible delivery pressure (continuous) 120 bar at 2900 rpm.

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Hydraulic oils, lubricating oils.

Operating Data
Handled fluid Lube oils, mineral and synthetic types.
Viscosity range From 10 to 5000 cSt
Pump speed From 2900 to 3500 rpm. *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 650 LPM - 40 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 40 bar.
Operating temperature range From 0 to 120 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication Lubricated for life..
Mounting arrangement Horizontal or vertical (also vertical semi-submerged, thanks to the intermediate flange).
Inlet & Outlet connection Suction port: BSP thread - Delivery port: SAE 3000.

Materials
Casing/Flanges Light alloy, GGG-40 on request *
Screws Nitrided steel *
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

17
Screw Pumps POF-PWOF Series Technical Specifications

SCREW PUMPS

Dimensions in mm unless otherwise stated.

SAE
Model A B C D E F H I L M N P T V d1 d2 d3 d4 d5 d6 d7 d8 d9
POF025#6 397 76 43 35 7 15 74.5 207 278 25 1" 1" 21.5 6 19 100 125 140 136 11 140 160 160
POF029#6 397 76 43 35 7 15 74.5 207 278 25 1" 1" 21.5 6 19 100 125 140 136 11 140 160 160
POF032#6 441 76 43 35 7 15 74.5 251 322 25 1" 1" 21.5 6 19 100 125 140 136 11 140 160 160
POF040#6 530 96 49 40 7 15 81 315 386 25 1½” 1½” 24.5 6 22 125 160 152 178 13 180 215 200
POF045#6 583 96 49 40 7 15 81 361 440 30 1½” 1½” 27 8 24 125 160 152 178 13 180 215 200
POF055#6 669 126 64 55 7 15 100 408 479 28 2" 3" 35 10 32 125 160 200 200 13 235 265 265
POF060#6 726 126 64 55 7 15 100 465 536 28 2" 3" 35 10 32 125 160 200 200 13 235 265 265

18
Screw Pumps 2SP LS Series Technical Specifications

SCREW PUMPS

Non lubricating low and medium viscosity and corrosive fluids

Suitable for water, light chemical and petrochemical products, fuel and heavy oils.

Admissible delivery pressure (continuous) 10 bar at 1000 to 3600 rpm.

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Cargo, transfer, lube system, stripping.

Operating Data
Handled fluid Fuel oil HFO - DO - LSMGO hydraulic and Lube oils.
Viscosity range From 0.7 to 15.000 cSt
Pump speed From 750 to 3600 rpm. *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 10,000 LPM - 600 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 40 bar.
Operating temperature range From 0 to 300 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication Dependent on application.
Mounting arrangement Horizontal or vertical (with foot).
Inlet & Outlet connection DIN standard (ANSI on request).

Materials
Casing/Flanges GGG-40 or carbon steel.
Screws Nitrided steel *
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

19
Screw Pumps 2SP LS Series Technical Specifications

SCREW PUMPS

Dimensions in mm unless otherwise stated.

IN OUT
Model A B C D E F G1 G2 dG Ø H M d1 Ø N l dl Ø nl O dO Ø nO
2SP LS 090 850 300 450 180 350 75 180 250 22 32.5 8 28 24 3" ¾” 4 2" ¾” 4
2SP LS 110 850 300 450 180 350 95 180 250 22 40 8 30 26 3" ¾” 4 2" ¾” 4
2SP LS 130 950 350 525 225 375 110 200 300 26 50 10 35 30 4" ¾” 8 3" ¾” 4
7
2SP LS 170 1075 400 575 280 410 125 230 350 26 65 12 40 35 5" /8” 8 4" ¾” 8
7 7
2SP LS 210 1200 475 700 315 450 133 260 410 34 80 14 50 44.5 6" /8” 8 5" /8” 8
7 7
2SP LS 270 1350 575 850 400 500 150 300 475 34 100 18 60 53 6" /8” 8 5" /8” 8

20
Screw Pumps 2SP Series Technical Specifications

SCREW PUMPS

Non lubricating low and medium viscosity and corrosive fluids

Suitable for water, light chemical and petrochemical products, fuel and heavy oils.

Admissible delivery pressure (continuous) 16 bar at 1000 to 3600 rpm.

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Cargo, transfer, lube system, stripping.

Operating Data
Handled fluid Fuel oil HFO - DO - LSMGO hydraulic and Lube oils.
Viscosity range From 0.7 to 15.000 cSt
Pump speed From 750 to 3600 rpm. *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 20,000 LPM - 1200 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 40 bar.
Operating temperature range From 0 to 300 °C *
Seal Mechanical seal.
Bearing type Radial ball on main shaft.
Bearing lubrication Dependent on application.
Mounting arrangement Horizontal or vertical (with foot).
Inlet & Outlet connection DIN standard (ANSI on request).

Materials
Casing/Flanges GGG-40 or carbon steel.
Screws Nitrided steel *
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

21
Screw Pumps 2SP - L2 Series Technical Specifications

SCREW PUMPS

Dimensions in mm unless otherwise stated.

IN OUT
Model A B C D E F G1 G2 dG Ø H1 H2 L M d1 Ø N P Q R S l dl Ø nl O dO Ø nO
7 7
2SP090 1050 720 800 505 410 285 360 380 22 300 255 70 8 28 24 535 515 360 32.5 8" /8” 8 6" /8” 8
7 7
2SP110 1050 720 800 505 410 285 360 380 22 300 255 70 10 32 27 535 515 360 40 8" /8” 8 6" /8” 8
7
2SP130 1100 760 850 585 450 300 380 400 26 330 280 82 12 40 35 560 540 380 50 10" 1" 12 8" /8” 8
2SP170 1300 1000 1000 660 460 355 420 440 26 380 315 90 16 55 49 665 635 500 65 12" 1" 12 10" 1" 12
2SP210 1500 1100 1100 785 520 410 450 475 34 480 400 104 18 65 58 770 730 550 80 16" 11/8” 16 12" 1" 12
2SP270 1800 1320 1300 910 600 490 530 555 34 550 450 125 20 70 62.5 920 880 660 100 20" 11/4” 20 16 11/8” 16

22
Screw Pumps 2SP - L3 Series Technical Specifications

SCREW PUMPS

Dimensions in mm unless otherwise stated.

IN OUT
Model A B C D E F G1 G2 dG Ø H1 H2 L M d1 Ø N P Q R S l dl Ø nl O dO Ø nO
7 7
2SP090 1205 720 800 505 410 360 360 380 22 300 255 70 8 28 24 615 590 360 32.5 8" /8” 8 6" /8” 8
7 7
2SP110 1210 720 800 505 410 365 360 380 22 300 255 75 10 32 27 615 595 360 40 8" /8” 8 6" /8” 8
7
2SP130 1265 760 850 585 450 380 380 400 26 330 280 82 12 40 35 645 620 380 50 10" 1" 12 8" /8” 8
2SP170 1470 1000 1000 660 460 440 420 440 26 380 315 90 16 55 49 750 720 500 65 12" 1" 12 10" 1" 12
2SP210 1675 1100 1100 785 520 500 450 475 34 480 400 104 18 65 58 855 820 550 80 16" 11/8” 16 12" 1" 12
2SP270 1975 1320 1300 910 600 580 530 555 34 550 450 125 20 70 62.5 1005 970 660 100 20" 11/4” 20 16 11/8” 16

23
Screw Pumps Twin Screw 2SP Series Screw Pumps

SCREW PUMPS

Are available in four different arrangements suitable to match most of the applications.
Custom versions available on request.

L1
One mechanical seal package; lubricating fluids only.
Lube oil Fuel oil Hydraulic Oil. Every fluid with lubricant characteristics.
Self priming, double entry design, with internal bearings and synchronised timing gear.
One mechanical or packing seal.

» Working temperature up to 100°C.

» Viscosity range up to 1500 cSt.
» Inlet pressure up to 6 bar.
» Differential pressure up to 16 bar.
» Speed up to 3500 rpm.

L2
Four “component” mechanical seal packages.
Non lubricating low and medium viscosity and corrosive fluid.
Self priming, double entry design, with external bearings separated by seals. Compact design for a
simple maintenance and cheapest solution. Shaft seal shall be single or double.

» Working temperature up to 150°C.

» Viscosity range up to 1500 cSt.
» Inlet pressure up to 6 bar.
» Differential pressure up to 16 bar.
» Speed up to 3500 rpm.

L3
Four “cartridge” mechanical seal.
Non lubricating low and medium viscosity and corrosive and dangerous fluids.
Self priming, double entry design, with external bearings separated by seals. Long shaft design
suitable for a wide range of seals. Possibility of cartridge design installation.

» Working temperature up to 200°C.

» Viscosity range up to 2500 cSt.
» Inlet pressure up to 6 bar.
» Differential pressure up to 16 bar.
» Speed up to 3500 rpm.

L4
Four API 682 mechanical seal.
Non lubricating low and medium viscosity, corrosive and dangerous fluids in heavy duty
service with operating more than 3 year.
Self priming, double entry design, with external bearings separated by seals. Strong shaft design for
all dangereous fluids in all conditions. Design to meet API 676 and all API 682 mechanical seal
configurations. Possibility to work in mixed phases.

» Working temperature up to 300°C.

» Viscosity range up to 15000 cSt.
» Inlet pressure up to 10 bar.
» Differential pressure up to 40 bar.
» Speed up to 3500 rpm.

24
Screw Pumps MPV2 Series Technical Specifications

SCREW PUMPS

For hydraulic or lubricating oils.

Maximum pressure 40 bar or 200 bar (depending by flow meter dimension)..

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Fuel consumption, control cargo and transfer flow.

Technical Characteristics
Delivery flow Up to 7.000 LPM - 420 m3/h (standard version
Pressure Versions nominal pressure 40bar or 200bar
Admissible temperature -15 to +150°C
Precision Class 0,2%
Type of O/P Square wave signal in frequency, direct function of flow rate*

Materials
Casing GGG-40 or carbon steel, aluminium
Flanges Carbon steel
Screws Nitrided steel *
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

Connection Size
Size Qminimum (lpm) Q nominal (lpm) Q maximum (lpm) Version
Flange Threaded
22 0.4 48.8 73.0 SAE 3000 - 1¼” G1" Standard
40 2.9 291 436.5 SAE 3000 - 2" G1½” Standard
62 10.8 1,078 1,617 SAE 3000 - 3" G2½” Standard
80 20.8 2,082 3,124 DN100 - PN40 G4" Standard
120 47.0 4,695 7,043 DN150 - PN40 X Standard
240 197.0 19,690 29,534 On request X On request

25
Screw Pumps MPV2 Series Technical Specifications

SCREW PUMPS

Alternative mounting
SAE or DN flange
(see dimensional chart)

MPV2 022 - 040 - 062

SAE connection

E (GAS thread)
D (metric thread)

C1 (SAE)
C (SAE)
A

MPV2 080 - 120

ØB DN connection

D (metric thread)

ØF (DN)

E (GAS thread)

Dimensions in mm unless otherwise stated.

Flow Meter Size A B C C1 F SAE/DN D E Maximum Pressure (bar)

022 158 79 30.2 58.7 - SAE1¼ 3000 psi M10 1" 40
040 230 109 42.9 77.8 - SAE 2" 3000 psi M12 1½” 200
062 335 200 61.9 106.4 - SAE3" 3000 psi M16 2¼” 200 (140 when connected with SAE flange)
080 396 235 - - 190 DN100 PN40 M20 4" 40
120 522 300 - - 220 DN150 PN40 M22 - 40

AVAILABLE COMPLETE SYSTEMS for CUSTOMIZED fuel consumption control complete of:
» Single Control system (after Feeder pump). » Remote Display (Control Room) via Ethernet, Wi-Fi.
» Single Control System for Flow difference (after circulation pump - fuel motor return).
» Data transmission to the Control Room.
» Control Systems for two or more Diesel Engines. » Data transmission to Land Office (Internet, GSM, satellite).
» Local display (Engine Room). » Warning Service (SMS, E-mail).

26
Screw Pumps PDP Series Technical Specifications

SCREW PUMPS

Double pump station for fuel oil.

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Booster, Feeder, Fuel supply.

Operating Data
Handled fluid Fuel oil HFO - DO - LSMGO hydraulic and Lube oils.
Viscosity range From 1,2 to 5000 cSt
Pump speed From 750 to 3600 rpm. *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 200 LPM - 12 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 16 bar (from 1000 to 3600 rpm)
Operating temperature range From 0 to 150 °C (*)
Inlet & Outlet connection DN40 ANSI 150
Cartridge filtration / surface 500 micron / 500 cm2

MATERIALS
Casing/Flanges Modular cast Iron GGG40
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

27
Screw Pumps PDP Series Technical Specifications

SCREW PUMPS

28
Screw Pumps SPB Series Technical Specifications

SCREW PUMPS

Double pump station for fuel oil.

Installation Data
Installation Indoor or Outdoor.
Environment Marine, Industrial.
Application Boiler, burner.

Operating Data
Handled fluid Fuel oil HFO - DO - LSMGO Hydraulic and lube oils.
Viscosity range From 1,2 to 5000 cSt
Pump speed From 750 to 3600 rpm. *
Rotation (viewed from coupling end) CW (Std version; CCW on demand).

Technical Characteristics
Flow rate Up to 41 LPM - 2.5 m3/h.
Suction pressure From - 0,5 to 10 bar.
Delivery pressure Up to 16/40 bar (from 1000 to 3600 rpm)
Operating temperature range From 0 to 150 °C (*)
Inlet & Outlet connection DN32 PN40
Cartridge filtration / surface 100 micron / 150 cm2

MATERIALS
Casing/Flanges Modular cast Iron GGG40
O-rings Viton ®
Surface protection On request.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

29
Screw Pumps SPB Series Technical Specifications

SCREW PUMPS

30
Screw Pumps Magnetic Coupling Drive

SCREW PUMPS

No Mechanical Seal No Parts In Contact Sealed System

Installation Data
Applicable to all PUMPS SIZE: PB series (from 3 to 41 lpm) at 16 / 40 bar
PHS series (from 6 to 200 lpm) at 16 bar
PZ series (from 30 to 4.800 lpm) at 16 bar
More usual applications: FUEL SUPPLY: Cargo, Transfer, Separator, Feeder, Circulating, Boiler/Burner

Operating Data
Handled Fluids: HFO, DO, GO, LSMGO
(all fluids with some lubricant properties but dangerous in case of leakage)
Minimum viscosity: From 1,2cSt

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

Advantages
» Safety
» System efficiency
» Regulations compliance
» Reliability
» Performance with low sulfur and low viscosity fluid
» Cuts maintenance costs as there is no mechanical seal

31
Screw Pumps Performance Chart

SCREW PUMPS

20,000 - 1,200

10,000 - 600

Speed rotation to be evaluated

Max. 1.800 rpm
4,800 - 288

Speed rotation to be evaluated

Up to 072 pump size max. 3,600 rpm / over max.1,800 rpm

Up to 072 pump size max. 3,600 rpm / over max.1,800 rpm

1,400 - 84
1,300 - 78

Max. 1800 rpm

650 - 39

560 - 33.6

420 - 25
Max. 3,600 rpm

Max. 3,600 rpm

200 - 12

100 - 6
Max. 3,600 rpm

41 - 2.46
Max. 3,600 rpm

30 - 1.8

11 - 0.66
9 - 0.54
6 - 0.36
3 - 0.18
Capacity (l/min - m3)
Viscosity range (cSt) 1.2 - 5,000 1.2 - 5,000 1.2 - 5,000 1.2 - 5,000 10 - 5,000 1 - 15 10 - 5,000 10 - 400 0.7 - 15,000 0.7 - 15,000

Model pump PB PHS PZ PZD PXF PWO fuel PWOF oil PWOF oil Twin 2SP LS Twin 2SP

Nominal pressure (bar) PN16 PN16 PN16 PN16 PN30 PN40 PN120 PN100 PN16/PN40 PN16/PN40
Special sizes

Fuel and diesel oil pump

Lube oil pump
Boiler pump
Application Hydraulic pump
Transfer*
Transfer*

32
 12
17
Quality Products for Mechanical
& Fluid Power

SCREW PUMPS
 an excellence in engineering

The comprehensive service for the

mechanical power transmission & fluid power industries.

Three Rotor Screw Pumps

For hydraulic oils, lube oils, coolant/cutting oils, fuels, and others. From pumping low lubricity fluids (like in the cooling lubrication –
machine tools sector) up to very high viscous fluids (lubrication in heavy industry and wind power generation), including specifically
designed pump for critical applications in hydraulics and high pressure lube skids. These screw pumps are functionally tested and
inspected prior to shipment. Certificates are available. This catalogue will grow steadily in the coming weeks. Please check
periodically for updates on further models not currently listed.

Suitable for pumping: Great benefits are:

• Mineral and Synthetic Lubricating oils • Very low pulsation level
• Fluids with low lubricating properties * • Very low noise level
• HFC, fire resistant fluids • High self priming capacity
• Fuel oils (HFO, LFO, diesel, Kerosene) • Wide compatibility with high viscosity media
• Fluids for aeronautic • Optimal performances also with air in oil media
* example: water based emulsion for machine tools • No pollutant release into pumped media
• Low pump maintenance
Main characteristics:
• Flow rate up to 10.000 litre/minute (ca. 2,700 USGPM)
• Working pressure up to 120 bar (1.700 psi) - continuous *
• Viscosity - operational range: 1 to >100.000 cSt *
• Superb perfomances even with air entrapped in the oil **
• Wide range availability for materials of construction
* according to model & execution
** specific execution apply.

PXF series PWO series PDA series PZ series

You
Tube

quality products for mechanical & fluid power

01737 767493 info@jbj.co.uk www.jbj.co.uk

jbj Techniques Limited is ISO certificated,
A range of products ATEX certificated
committed to international coordination - registered in England No: 1185469 -
to directive 94/9/E requirements
& unification of industrial standards.
Screw Pumps PDA Series Characteristics

SCREW PUMPS

Aluminium alloy flange

‘O’-ring
Aluminium alloy pump casing
Aluminium alloy plug

Key

Cast iron idler spindle

Ball bearing
Safety valve
Steel driving spindle
Mechanical seal

Screw pumps – PDA series with valve and ISO motor connection flange.
For hydraulic oils, lubricating oils.

Admissible delivery pressure: 10 bar

Standard valve setting: 6 bar

Main field of application: Low pressure lubrication systems, auxiliary filtration systems, cooling systems

Technical Characteristics

Delivery flow: 21 to 160 lpm (5.5 to 42.2 US gpm).

Admissible suction pressure: 0.4 to 2 bar (5.8 to 29 psi).*
Admissible delivery pressure: up to 10 bar (145 psi).*
Kinematics viscosity: 20 to 400 cSt.*
Admissible temperature: 0 to 100 °C (32 to 212 °F).*
Driving speed: 750 to 3600 rpm.
Average noise level: 56 - 62 dB(A) at 2900 rpm according to pump dimension.
Recommended filtration: 60 micron max, suction side (not abrasive contaminant).
ISO4406 19 / 16 – NAS 10.
Direction of rotation: Clockwise, as seen from the driving side.
Reduced pressure limits apply due to fluid viscosity and driving speed.
Consult the performance charts for the individual pump size.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

1
Screw Pumps PDA Series Dimensions

SCREW PUMPS

Shaft detail

Dimensions in mm unless otherwise stated.

Model A B C D E F L M N P T V d1 d2 d3 d4 d5 d6

Gas Gas

PDA029#2...01
286 122 44 1" 1"
PDA032#2...01 82 42 37 5 14 21.5 6 19 100 125 150 95 11

PDA040#2...01 307 140 48 1¼” 1¼”

2
Screw Pumps PDA Series Characteristics

SCREW PUMPS

Aluminium alloy bellhousing (MEC 80/90 b5 Ø200

Coupling locking nut

Aluminium alloy pump casing
Aluminium alloy plug
‘O’-ring

Key

Ball bearing Cast iron idler spindle

Mechanical seal
Steel driving spindle Safety valve
Torsionally flexible shaft coupling
motor shaft Ø24
pump shaft Ø19

Screw pumps – PDA series with valve and ISO integrated bellhousing (motor 80/90).
For hydraulic oils, lubricating oils.

Admissible delivery pressure: 10 bar

Standard valve setting: 6 bar

Main field of application: Low pressure lubrication systems, auxiliary filtration systems, cooling systems

Technical Characteristics

Delivery flow: 21 to 160 lpm (5.5 to 42.2 US gpm).

Admissible suction pressure: 0.4 to 2 bar (5.8 to 29 psi).*
Admissible delivery pressure: up to 10 bar (145 psi).*
Kinematics viscosity: 20 to 400 cSt.*
Admissible temperature: 0 to 100 °C (32 to 212 °F).*
Driving speed: 750 to 3600 rpm.
Average noise level: 56 - 62 dB(A) at 2900 rpm according to pump dimension.
Recommended filtration: 60 micron max, suction side (not abrasive contaminant).
ISO4406 19 / 16 – NAS 10.
Direction of rotation: Clockwise, as seen from the driving side.
Reduced pressure limits apply due to fluid viscosity and driving speed.
Consult the performance charts for the individual pump size.

*Contact jbj Techniques technical office for different values, telephone: +44 (0)1737 767493 or email: info@jbj.co.uk

3
Screw Pumps PDA Series Dimensions

SCREW PUMPS

Dimensions in mm unless otherwise stated.

Model A B C D F G G1 H I L d2 d3 d4 d6

Gas Gas

PDA029#2...01 STD.
1" 1" 353 226 44 122
PDA032#2...01 STD. 191 67 127

PDA040#2...01 STD. 1¼" 1¼" 374 247 48 140

35 130 165 200 M10
PDA029#2...01 OPT.
1" 1" 284 226 44 122
PDA032#2...01 OPT. 122 2 58

PDA040#2...01 OPT. 1¼" 1¼" 305 247 48 140

4
Screw Pumps PDA Series Motor Pump Dimensions

SCREW PUMPS

B C D E

F F1
H

I1

I
G

L
Q
S1
S

ØY
ØX

R
R1
ØW
ØZ

Dimensions in mm unless otherwise stated.

Motor A B C D E F F1 G H I I1 L Q R R1 S S1 W X Y Z
PDA029 71A-71B 562 220 98 82 122 1” 1” 71 120 44 44 45 7 90 109 112 150 9 110 160 130
80A-80B 608 255 127* 64 122 1” 1” 80 145 44 44 50 10 100 126 125 165 11 145 200 165
90S 618 265 127* 64 122 1” 1” 90 155 44 44 56 10 100 130 140 180 11 145 200 165
90L 643 290 127* 64 122 1” 1” 90 155 44 44 56 10 125 155 140 180 11 145 200 165
100L 705 325 136 82 122 1” 1” 100 180 44 44 63 12 140 172 160 205 14 190 250 215
112M 720 340 136 82 122 1” 1” 112 190 44 44 70 12 140 176 190 230 14 190 250 215
PDA032 80A-80B 608 255 127* 64 122 1” 1” 80 145 44 44 50 10 100 126 125 165 11 145 200 165
90S 618 265 127* 64 122 1” 1” 90 155 44 44 56 10 100 130 140 180 11 145 200 165
90L 643 290 127* 64 122 1” 1” 90 155 44 44 56 10 125 155 140 180 11 145 200 165
100L 705 325 136 82 122 1” 1” 100 180 44 44 63 12 140 172 160 205 14 190 250 215
112M 720 340 136 82 122 1” 1” 112 190 44 44 70 12 140 176 190 230 14 190 250 215
132SA-132SB 789 390 155 82 122 1” 1” 132 210 44 44 89 12 140 176 216 270 14 234 300 265
PDA040 80A-80B 629 255 127* 64 140 1¼” 1¼” 80 145 48 48 50 10 100 126 125 165 11 145 200 165
90S 639 265 127* 64 140 1¼” 1¼” 90 155 48 48 56 10 100 130 140 180 11 145 200 165
90L 664 290 127* 64 140 1¼” 1¼” 90 155 48 48 56 10 125 155 140 180 11 145 200 165
100L 726 325 136 82 140 1¼” 1¼” 100 180 48 48 63 12 140 172 160 205 14 190 250 215
112M 741 340 136 82 140 1¼” 1¼” 112 190 48 48 70 12 140 176 190 230 14 190 250 215
132SA-132SB 810 390 155 82 140 1¼” 1¼” 132 210 48 48 89 12 140 176 216 270 14 234 300 265
* Bellhousing included

5
Screw Pumps PDA Series 50 Hz Performance Chart

SCREW PUMPS

Pump size PDA029#2A

Pump size PDA029#2B

Pump size PDA032#2A

Pump size PDA032#2B

6
Screw Pumps PDA Series 50 Hz Performance Chart

SCREW PUMPS

Pump size PDA040#2A

Pump size PDA040#2B

Pump size PDA040#2C

7
Screw Pumps PDA Series 60 Hz Performance Chart

SCREW PUMPS

Pump size PDA029#2A

Pump size PDA029#2B

Pump size PDA032#2A

Pump size PDA032#2B

8
Screw Pumps PDA Series 60 Hz Performance Chart

SCREW PUMPS

Pump size PDA040#2A

Pump size PDA040#2B

Pump size PDA040#2C

9
jbj Techniques is a specialist supplier of high-quality jbj Techniques provides one of the widest ranges of
products for the mechanical power transmission and couplings available within the UK; mechanical power
fluid power sectors. The company offers a high level transmission couplings for a vast range of applications.
of in-house expertise plus a huge selection of products Ranging from miniature couplings, all steel gear couplings,
to meet a very broad range of customer applications. flexible spider couplings, shaft couplings, torque limiting
From specification, through technical advice and manufacture couplings, disc and grid type couplings, ATEX compliant and
to after-sales support, jbj Techniques provides a shaft locking devices. Magnetic couplings for power
comprehensive and valued service to the power transmission transmission between hermetically sealed areas. However as
and hydraulics industries. The company fields a UK-wide team extensive as the selection is, couplings make up a fraction of
of technical sales engineers to ensure that the business is jbj’s portfolio. As power transmission specialists the company
close to its customers, and it enjoys excellent associations stock and provide gearboxes, clutches, pumps, hydraulic
with European manufacturers, acting as sole UK distributor motors, flow meters, fluid power accessories including: cooling
in many cases. & heat exchange products, reservoirs, pipe flanges, seals and
level indicators, as well as a variety of bellhousings and engine
jbj’s team is recognised for its expertise in the selection and adaptors, to name just a few of the product categories.
configuration of hydraulic and mechanical transmission
systems. Able to draw on an extensive product range that jbj Techniques Limited is proud of it’s relationship
provides the building blocks for bespoke systems both large and reputation with customers and suppliers.
and small, the in-house design team offers a complete The core client base is stable and loyal, which
service, ranging from an assessment of customer is testament to the quality of service
requirements to full technical backup, including product provided by the company. A similar
specification, CAD based system design, system build and relationship exists with suppliers,
certification. Moreover customers can take advantage of jbj’s ensuring a continuing high quality
own machine-shop facilities and skilled engineers to guarantee service in which customers can have
quality and control costs. complete confidence.

i v e li ne
Bellhousings Torsionally Flexible Couplings Torsionally Rigid Couplings D r
Torsional Couplings Anti-static/Flameproof Couplings Tyre Couplings Torque Limiting Couplings

Permanent Magnetic Couplings Hydraulic Adaptors Engine Adaptor Kits Dampers

from
Small
Individual Components to
Large Combinations

“ ensuring a continuing high

quality service in which
customers can have
complete confidence.
“
 an excellence in engineering

comprehensive range of components www.jbj.co.uk

Gear Pumps/Motors Screw Pumps Axial & Radial Piston Motors LSHT Motors/Geared Motors Vane Pumps

Splitter Gearboxes Pneumatic Motors & Starters

a r m o n y BD Clutches & Gearboxes BDS Clutches Planetary Gearboxes

e H
Coolers Oil Bath Clutches

Flow Dividers Tanks/Accessories Fluid Level Indicators Flanges

Mini Power Packs Pressure Intensifiers

You
Tube

quality products for mechanical & fluid power

01737 767493 info@jbj.co.uk www.jbj.co.uk

jbj Techniques Limited is ISO certificated,
A range of products ATEX certificated
committed to international coordination - registered in England No: 1185469 -
to directive 94/9/E requirements
& unification of industrial standards.
 jbj Techniques Limited
28 Trowers Way Holmethorpe Industrial Estate
Redhill Surrey RH1 2LW. UNITED KINGDOM

quality products for mechanical & fluid power

01737 767493 info@jbj.co.uk www.jbj.co.uk

You
Tube

jbj Techniques Limited is ISO certificated,

committed to international coordination & registered in England No: 1185469 A range of products ATEX certificated
unification of industrial standards. to directive 94/9/EC requirements

set by James Harris, jbj Techniques Limited