Untitled

䐀椀猀琀
爀椀戀甀椀搀漀爀
刀攀瘀攀渀搀愀
䌀漀渀猀攀爀琀漀猀
⠀
㄀㄀⤀
㐀㄀㜀㐀ⴀ
㌀㌀　　
Mobile Hydraulic Pumps
T6*M
Denison Vane Technology, fixed displacement
Catalogue HY29-0002/UK Hydraulic Pumps, Fixed
Contents Series T6 Mobile, Denison Vane Pumps
GENERAL Features..................................................................................................................3
Instructions..............................................................................................................3
Minimum & maximum speeds.................................................................................4
Pressure ratings......................................................................................................4
Priming at starting...................................................................................................4
Minimum allowable inlet pressure............................................................................5
General characteristics............................................................................................5
Pump selection : Routine and example...................................................................6
Intermittent pressure rating.....................................................................................6
Description..............................................................................................................7
Application advantages...........................................................................................7
Shafts and hydraulic fluids.......................................................................................8
Notes.......................................................................................................................9
T6CM Ordering code & Technical data............................................................................10

Dimensions & Operating characteristics................................................................11
T6CP Ordering code & Technical data............................................................................12

T6D* Ordering code & Technical data............................................................................14

T6E* Ordering code & Technical data............................................................................16

T6CC* Ordering code & Technical data............................................................................18

T6DC* Ordering code & Technical data............................................................................20

T6EC* Ordering code & Technical data............................................................................22

T6ED* Ordering code & Technical data............................................................................24
T6DCCM Ordering code & Operating characteristics...........................................................26

Dimensions............................................................................................................27
Technical data........................................................................................................28
T6EDC* Technical data........................................................................................................29

Dimensions T6EDCM............................................................................................30
Dimensions T6EDCS.............................................................................................31
Ordering code & Operating characteristics...........................................................32
Additional shafts....................................................................................................33
Porting diagrams for double pumps.......................................................................34
Porting diagrams for triple pumps...................................................................34 - 35
Parker Hannifin SAS

2
VPDE, Denison Vane Pumps
Vierzon - France
Features Series T6 Mobile, Denison Vane Pumps
GREATER FLOW Greater flow for the envelope size is achieved by increased displacement cam rings
at high permissible speeds with atmospheric inlet
C → 3 to 31 GPM, 10 to 100 ml/rev.
D → 14 to 50 GPM, 48 to 158 ml/rev.
E → 42 to 72 GPM, 132 to 227 ml/rev.
HIGHER PRESSURE Pressure ratings to 275 bar reduce size and cost of actuators, valves and lines, give
extended life at reduced pressures.
BETTER EFFICIENCY Better efficiency under load increases productivity, reduces heating and operating costs.
MOUNTING FLEXIBILITY Up to 32 positions for double pumps and up to 128 for triple pumps: this reduces mounting
costs and improves performance.
LOWER NOISE LEVELS Increase operator safety and acceptance.
COMPLETE CONFORMITY To SAE - J744c 2-bolt standards and to ISO 3019-1 (T6EDCS SAE E, T6EDCM ISO
3019/2) in the various keyed and splined shaft options offered.
CARTRIDGE DESIGN Provides for drop-in assemblies. This allows easy conversion or renewal of serviceable
elements in minutes at minimum expense and risk of contamination. The “C” & “D” cartridge
pumps are birotational and indicated by “B” description in cartridge model number. Pump
rotation is easy to change by changing position of cam ring on port plate dowel pin hole.
WIDER RANGE OF Viscosities from 2000 to 10 cSt permit colder starts and hotter running. The balanced design
ACCEPTABLE VISCOSITIES compensates for wear and temperature changes. At high viscosity or cold temperature,
the rotor to side plates gap is well lubricated and improves mechanical
efficiency.
FIRE RESISTANT FLUIDS Including phosphate esters, chlorinated hydrocarbons, water glycols and invert emulsions
may be pumped at higher pressures and with longer service life by these pumps.
GENERAL APPLICATIONS 1. Check speed range, pressure, temperature, fluid quality, viscosity and pump rotation.
INSTRUCTIONS 2. Check inlet conditions of the pump, if it can accept application requirement.
3. Type of shaft : if it would support operating torque.
4. Coupling must be chosen to minimize pump shaft load (weight, misalignment).
5. Filtration : must be adequate for lowest contamination level.
6. Environment of pump : to avoid noise reflection, pollution and shocks.
3 Parker Hannifin SAS

Vierzon - France
Speed and pressure ratings Series T6 Mobile, Denison Vane Pumps
Theoretical Maximum Speed Maximum Pressure

Displacement Minimum HF-0,HF-1 HF-3, HF-4 HF-0, HF-2 HF-1, HF-4, HF-5 HF-3
Size Series Vi Speed HF-2 HF-5 Int. Cont. Int Cont Int Cont
ml/rev. RPM RPM RPM bar bar bar bar bar bar
B03 10,8
B05 17,2
B06 21,3
B08 26,4
B10 34,1
CM B12 37,1 400 2800 1800 275 240 210 175 175 140
CP
B14 46,0
B17 58,3
B20 63,8
B22 70,3
B25 79,3
B28 88,8 2500 210 160 160
B31 100,0
B14 47,6
B17 58,2
B20 66,0
B24 79,5
DM B28 89,7 400 2500 1800 240 210 210 175 175 140
DP B31 98,3
B35 111,0
B38 120,3
B42 136,0
B45 145,7 2200
B50 158,0 210 160 160
042 132,3
045 142,4
EM
050 158,5
EP 400 2200 1800 240 210 210 175 175 140
052 164,8
062 196,7
066 213,3
072 227,1
HF-0, HF2 = Antiwear Petroleum Base

HF-1 = Non Antiwear Petroleum Base
HF-5 = Synthetic Fluids
HF-3 = Water in oil Emulsions
HF-4 = Water Glycols
For further information or if the performance characteristics outlined above do not meet your own particular requirements,
please consult your local Parker office.
PRIMING AT STARTING At first, start operation of the pump shaft at the lowest speed and at the lowest pressure to obtain
priming. When a pressure relief valve is used at the outlet, it should be backed off to minimize
return pressure.
When possible, an air bleed off should be provided in the circuit to facilitate purging of system
air.
Never operate pump shaft at top speed and pressure without checking for completion of pump
priming, and the fluid has no aeration disaerated.
Parker Hannifin SAS

4
Vierzon - France
Minimum allowable inlet pressure (bar absolute) Series T6 Mobile, Denison Vane Pumps
Cartridge Speed RPM

Size Series 1200 1500 1800 2100 2200 2300 2500 2800 Series
B03 B03
B05 0,80 0,90 B05
B06 0,80 1,00 B06
B08 0,80 B08
B10 B10
CM B12 0,80 0,80 0,80 0,85 0,92 B12
CP B14 B14
B17 0,85 0,95 1,03 B17
B20 0,90 B20
B22 0,85 0,90 0,98 1,05 B22
B25 0,90 0,95 0,95 1,05 B25
B28 0,98 0,98 1,08 B28
B31 0,85 0,90 1,00 1,11 B31
B14 0,80 1,00 B14
B17 0,88 0,95 B17
B20 B20
B24 0,80 0,82 1,10 B24
DM B28 0,80 0,80 0,85 0,92 1,00 1,18 B28
DP B31 0,90 0,95 1,23 B31
B35 0,92 0,98 1,02 1,29 B35
B38 0,95 1,00 1,05 B38
B42 1,02 1,08 B42
B45 0,85 0,98 1,05 B45
B50 1,02 1,09 B50
042 0,88 042
045 045
050 0,80 0,80 0,80 0,90 1,00 050
EM
EP 052 052
062 0,85 0,95 062
066 0,85 0,85 0,95 1,00 1,09 066
072 0,85 1,05 072
Inlet pressure is measured at inlet flange with petroleum base fluids at viscosity between 10 and 65 cSt. The difference between inlet pressure at the
pump flange and atmospheric pressure must not exceed 0.2 bar to prevent aeration.
Multiply absolute pressure by 1,25 for HF-3, HF-4 fluids.
by 1,35 for HF-5 fluid.
by 1,10 for ester or rapeseed base.
Use highest cartridge absolute pressure for double & triple pump.
GENERAL CHARACTERISTICS
Weight without SAE 4 bolts
Moment of inertia J518c - ISO/DIS 6162-1 - 4) ISO/DIS 6162-2
Mounting standard connector and
kgm2 x 10-4
bracket - kg Suction Pressure
SAE J744c
T6CM 15,7 7,5 1.1/2" 1"
ISO/3019-1 SAE B
T6CP 18,0 7,8 2"4) 1.1/4"4)
SAE J744c
T6D* 24,0 23,3 2" 1.1/4"
ISO/3019-1 SAE C
T6E* 43,3 51,5 3" 1.1/2"
SAE J744c 2.1/2" or P1 P2
T6CC* 26,0 14,9
ISO/3019-1 SAE B 3” 1" 1" or 3/4"
T6DC* 36,6 30,4 3" 1.1/4" 1"
T6EC* 55,0 73,4 3.1/2" 1.1/2" 1"
SAE J744c
T6ED* 66,0 73,4 4" 1.1/2" 1"1/4
ISO/3019-1 SAE C
P1 P2 P3
T6DCC* 61,0 37,3 4"
1.1/4" 1" 1" or 3/4”
SAE “E” (T6EDCS)
T6EDC* 100,0 80,2 4" 1.1/2" 1.1/4" 1" or 3/4”
ISO/3019-2 (T6EDCM)

Vierzon - France
Pump Selection Series T6 Mobile, Denison Vane Pumps
CALCULATION To resolve Performances required

Volumetric displacement Vi [ml/rev.] Requested flow Q [l/min] 60
Available flow Q [l/min] Speed n [R.P.M.] 1500
Input power P [kW] Pressure p [bar] 150
ROUTINE AND EXAMPLE Routine : Example :

1000 Q
1. First calculation Vi = Vi = 1000 x 60 = 40 ml/rev
n
1500
2. Choice Vi of pump immediately T6CM B14 Vi = 46 ml/rev.
greater (see tabulation)
3. Theoretical flow of this pump 46 x 1500

Vi x n Q = = 69 l/min
Qtheo. = theo. 1000
1000
4. Find Qper. leakage function of T6CM (page 10) : Qper. = 5 l/min at

pressure Qper. = f(p) on curve at 10 or 150 bar, 24 cSt
24 cSt
5. Available flow Q = Qtheo. - Qper. Q = 69 - 5 = 64 l/min
6. Theoretical input power 69 x 150

Q xp P = = 17,3 kW
Ptheo. = theo. theo. 600
600
7. Find ps hydrodynamic power loss T6CM (page10) : Ps at 1500 R.P.M.,

on curve 150 bar = 1,5 kW
8. Calculation of necessary input

power Peff. = Ptheo. + Ps P = 17,3 + 1,5 = 18,8 kW
}
9. Results Vi = 46,0 ml/rev
Qeff. = 64,0 l/min T6CM B14
Peff. = 18,8 kW
These calculation steps must be followed for each application.
INTERMITTENT PRESSURE T6 units may be operated intermittently at pressures higher than the recommended
RATING continuous rating when the time weighted average of pressure is less than or equal to
the continuous duty pressure rating.
This intermittent pressure rating calculation is only valid if other parameters; speed, fluid,
viscosity and contamination level are respected.
For total cycle time higher than 15 minutes, please consult your Parker representative.
Average Pressure Example : T6CM - B14

Pressure (bar)
cycle Duty cycle 4 min. at 275 bar

1 min. at 35 bar
5 min. at 160 bar
(4 x 275) + (1 x 35) + (5 x 160)
= 193,5 bar
10
Time (minutes) 193,5 bar is lower than 240 bar allowed as continuous pressure for T6CM - B14 with
HF-0 fluid.
Parker Hannifin SAS

6
Vierzon - France
Description Series T6 Mobile, Denison Vane Pumps
Cap end outlet port has Shaft end outlet port has
8-positions at 45° intervals Inlet 4-positions at 90° intervals’ Outlet Inlet
relative to inlet on T6DC. relative to inlet. Front & rear sideplates are
each clamped axially by the
separate discharge pressures
Pilot recess as required

by SAE for
full conformity
Shaft comes in variety
of keyed and splined
options to meet SAE
and ISO 3019-1.
Ball bearing hold

shaft in alignment.
T6*P
Cartridges are replaceable Front sideplate is clamped Cartridge is replaceable
double shaft seal
assemblies. Each includes axially by discharge assembly including cam
cam ring, rotor, vanes, pins and pressure to reduce internal ring, rotor, vanes, pins
sideplates. Drain ahole leakage. and sideplate
Vane is urged outward at Holes in cam ring Working vane on
suction ramp by pin force 90° section improve wide cartridge major arc pushes fluid
and centrifugal force. inlet characteristics to discharge port.
Suction ramp
where unloaded
vane moves out.
Section B-B
Pin cavity is at a steady

pressure slightly higher
than at discaharge port
Lub side holes lubricate Discharge ramp

the sideplate surfaces. where unloaded
Section A-A Working vane on minor arc
vane moves in.
seals discharge pressure from
the suction port
APPLICATION ADVANTAGES • The high pressure capability to 275 bar, in the small envelope, reduces installation
costs and provides extended life at reduced pressure.
• The high volumetric efficiency, typically 94%, reduces heat generation, and allows
speeds down to 400 RPM at full pressure.
• The high mechanical efficiency, typically 94%, reduces energy consumption.
• The wide speed range from 400 RPM to 2800 RPM, combined with large size
cartridge displacements, will optimize operation for the lowest noise level in the
smallest envelope.
• The low speed 400 RPM, low pressure, high viscosity 2000 cSt allow application in
cold environments with minimum energy consumption and without seizure risk.
• The low ripple pressure ± 2 bar reduces piping noise and increases life time of other
components in the circuit.
• The high resistance to particle contamination because of the double lip vane
increases pump life.
• The large variety of options (cam displacement, shaft, porting) allows customized
installation.
• The shaft option T (SAE J718c), allows direct drive (at 540 or 1000 RPM) on
tractors.
• The double shaft seal (T6*P version) and drain hole allow direct mounting onto
gear boxes.

Vierzon - France
Shafts and Fluid Series T6 Mobile, Denison Vane Pumps
RECOMMENDED FLUIDS Petroleum based antiwear R & O fluids.

These fluids are the recommended fluids for T6 series pumps. Maximum catalog ratings
aand performance data are based on operation with these fluids. These fluids are covered
by DENISON fluid specifications HF-0 and HF-2.
ACCEPTABLE ALTERNATE The use of fluids other than petroleum based antiwear R & O fluids, requires that the maximum
FLUIDS ratings of the pumps will be reduced. In some cases the minimum replenishment pressures
must be increased. Consult specific sections for more details.
VISCOSITY Max (cold start, low speed & pressure)_________________________ 2000 mm2/s (cSt)
Max (full speed & pressure)___________________________________ 108 mm2/s (cSt)
Optimum (max. life)__________________________________________ 30 mm2/s (cSt)
Min (full speed & pressure for HF-1, HF-3, HF-4 & HF-5 fluids)_ _______ 18 mm2/s (cSt)
Min (full speed & pressure for HF-0 & HF-2 fluids) __________________ 10 mm2/s (cSt)
VISCOSITY INDEX 90° min. higher values extend range of operating temperatures.
Maximum fluid temperature (θ) °C
HF-0, HF-1, HF-2____________________________________________________ + 100°
HF-3, HF-4 ________________________________________________________ + 50°
HF-5______________________________________________________________ + 70°
Biodegradable fluids (esters & rapeseed base)_____________________________ + 65°
Minimum fluid temperature (θ) °C

HF-0, HF-1, HF-2, HF-5_______________________________________________ - 18°
HF-3, HF-4 ________________________________________________________ + 10°
Biodegradable fluids (esters & rapeseed base)_____________________________ - 20°
FLUID CLEANLINESS The fluid must be cleaned before and during operation to maintain contamination level
of NAS 1638 class 8 (or ISO 19/17/14) or better. Filters with 25 micron (or better ß10 ≥ 100)
nominal ratings may be adequate but do not guarantee the required cleanliness levels. Suction
strainers must be of adequate size to provide minimum inlet pressure specified. 100 mesh
(149 micron) is the finest mesh recommended. Use oversize strainers or omit them altogether
on applications which require cold starts or use fire resistant fluids.
OPERATING TEMPERATURES Operating temperatures are a function of fluid viscosities, fluid type, and the pump.
AND VISCOSITIES Fluid viscosity should be selected to provide optimum viscosity at normal operating
temperatures. For cold starts the pumps should be operated at low speed and pressure until
fluid warms up to an acceptable viscosity for full power operation.
WATER CONTAMINATION IN Maximum acceptable content of water.

THE FLUID • 0,10 % for mineral base fluids.
• 0,05 % for synthetic fluids, crankcase oils, biodegradable fluids.
If amount of water is higher, then it should be drained off the circuit.
COUPLINGS AND FEMALE • The mating female spline should be free to float and find its own center. If both members
SPLINES are rigidly supported, they must be aligned within 0,15 TIR or less to reduce fretting. The
angular alignment of two spline axes must be less than ± 0,05 per 25,4 radius.
• The coupling spline must be lubricated with a lithium molydisulfide grease or a similar
lubricant.
• The coupling must be hardened to a hardness between 27 and 45 R.C.
• The female spline must be made to conform to the Class 1 fit as described in SAE-J498b
(1971). This is described as a Flat Root Side Fit.
KEYED SHAFTS Parker supplies the T6 series keyed shaft pumps with high strength heat-treated keys.
Therefore, when installing or replacing these pumps, the heat-treated keys must be used in
order to insure maximum life in the application. If the key is replaced it must be a heat-treated
key between 27 and 34 R.C. hardness. The corners of the keys must be chamfered from 0,76
to 1,02 at 45° to clear radii in the key way.
NOTE Alignment of keyed shafts must be within tolerances given for splined shafts.
SHAFT LOADS These products are designed primarily for coaxial drives which do not impose axial or side
loading on the shaft. Consult specific sections for more details.
Parker Hannifin SAS

8
Vierzon - France
Notes Series T6 Mobile, Denison Vane Pumps

Vierzon - France
Ordering Code Series T6CM, Denison Vane Pumps
Model No. T6CM - B22 - 1 R 00 - C 1
Series M = Mobile 1 shaft seal Modification

Cam ring Seal class
(Delivery at 0 bar & 1500 r.p.m.) 1 = S1 (for mineral oil)
B03 = 16,2 l/min B17 = 87,4 l/min 4 = S4 (for the resistant fluids)
B05 = 25,8 l/min B20 = 95,7 l/min 5 = S5 (for mineral oil and fire
B06 = 31,9 l/min B22 = 105,4 l/min resistant fluids)
B08 = 39,6 l/min B25 = 118,9 l/min
Design letter
B10 = 51,1 l/min B28 = 133,2 l/min
B12 = 55,6 l/min B31 = 150,0 l/min Porting combination
B14 = 69,0 l/min 00 = standard
Type of shaft Direct. of rotation (view on shaft end)
1 = keyed (SAE B) R = clockwise
2 = keyed (no SAE) L = counter-clockwise
3 = splined (SAE B)
4 = splined (SAE BB) P = Pressure port
S = Suction port
INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

T6CM - B22
Lp. Noise level [db(A)] 1m ISO 4412
Internal laeakage Qs [l/min]
Pressure p [bar] Pressure p [bar]

Do not operate the pump more than 5 seconds at any speed or
viscosity if internal leakage is more than 50 % of theoretical flow.
POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Power loss Ps [kW]
Shaft keyed N° 1
Load F [N]
Pressure p [bar] Speed n [RPM]

Maximum permissible axial load Fa = 800 N
Parker Hannifin SAS

10
Vierzon - France
Dimensions and Characteristics Series T6CM, Denison Vane Pumps
MOUNTING TORQUE 159 Nm.

KEY
6,35 MAX
M8 x 16 DEEP
24,94 MAX
Shaft Code 1
3/8"-16 UNC x 19 DEEP-4 HOLES
(Keyed SAE B)
1/2"-13 UNC x 22,4 DEEP-4 HOLES
KEY
Shaft Code 2
(Keyed no SAE)
24,53 MAX
Shaft Code 3 Shaft Code 4
SAE B splined shaft SAE B-B splined shaft SUCTION ø 38,1 PRESSURE ø 25,4 Shaft torque limits [ml/rev x bar]
Class 1-J498 b Class 1-J498 b
16/32 d.p -13 teeth 16/32 d.p. -15 teeth Pump Shaft Vi x p max.
30o pressure angle 30o pressure angle
flot root side fit flat root side fit
1 16500
2 14300
T6CM
3 20600
OPERATING CHARACTERISTICS - TYPICAL [24 cSt] 4 21800
Volumetric Speed Flow Q [l/min] Input power P [kW]

Series
Displacement Vi n [R.P.M.] p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
1000 10,8 - - 1,0 - -
B03 10,8 ml/rev
1500 16,2 10,7 - 1,3 5,3 -
1000 17,2 11,7 1,1 5,1 -
B05 17,2 ml/rev
1500 25,8 20,3 15,8 1,4 7,5 12,2
1000 21,3 15,8 11,3 1,1 6,0 10,0
B06 21,3 ml/rev
1500 31,9 26,5 22,0 1,5 8,9 14,7
1000 26,4 20,9 16,4 1,2 7,2 12,1
B08 26,4 ml/rev
1500 39,6 34,1 29,6 1,6 10,7 17,7
1000 34,1 28,6 24,1 1,3 8,9 15,1
B10 34,1 ml/rev
1500 51,1 45,7 41,2 1,7 13,4 22,3
1000 37,1 31,6 27,1 1,3 9,6 16,3
B12 37,1 ml/rev
1500 55,6 50,2 45,7 1,7 14,4 24,1
1000 46,0 40,5 36,0 1,4 11,7 19,9
B14 46,0 ml/rev
1500 69,0 63,5 59,0 1,9 17,6 29,5
1000 58,3 52,8 48,3 1,6 14,5 24,8
B17 58,3 ml/rev
1500 87,4 82,0 77,5 2,1 21,9 36,9
1000 63,8 58,3 53,8 1,6 15,8 27,0
B20 63,8 ml/rev
1500 95,7 90,2 85,7 2,2 23,8 40,2
1000 70,3 64,8 60,3 1,7 17,3 29,6
B22 70,3 ml/rev
1500 105,4 100,0 95,5 2,3 26,1 44,1
1000 79,3 73,8 69,3 1,8 19,3 33,2
B251) 79,3 ml/rev
1500 118,9 113,5 109,0 2,5 29,2 49,5
1000 88,8 83,3 80,12) 1,9 21,9 32,52)
B281) 88,8 ml/rev
1500 133,2 127,7 124,52) 2,8 32,7 48,52)
1000 100,0 94,5 91,32) 2,0 24,4 36,42)
B311) 100,0 ml/rev
1500 150,0 144,5 141,32) 2,8 36,5 54,42)
1) 2)
B25 - B28 - B31 = 2500 R.P.M. max. B28 - B31 = 210 bar max. int.
- Not to use because internal leakage greater than 50% theoretical flow. Port connection can be furnished with metric threads

Vierzon - France
Ordering Code Series T6CP, Denison Vane Pumps
Model No. T6CP - B22 - 2 R 00 - A 1
Series P = Mobile 2 shaft seals Modification

Cam ring Seal class
B17 = 87,4 l/min B28 = 133,2 l/min 5 = S5 (for mineral oil and fire resistant fluids)
B20 = 95,7 l/min B31 = 150,0 l/min
Design letter
B22 = 105,4 l/min
Porting combination
Type of shaft
00 = standard
2 = keyed (no SAE)
3 = splined (SAE C) Direct. of rotation (view on shaft end)
R = clockwise
L = counter-clockwise

P = Pressure port
S = Suction port

T6CP - B22
Internal leakage Qs [l/min]

Do not operate the pump more than 5 seconds at any speed or
viscosity if internal leakage is more than 50 % of theoretical flow.

Power loss Ps [kW]
Load F [N]
Shaft keyed N° 2
Parker Hannifin SAS

12
Vierzon - France
Dimensions and Characteristics Series T6CP, Denison Vane Pumps
MOUNTING TORQUE : 159 Nm
6,35 MAX
Shaft Code 3
SAE C Splined shaft
DRAIN HOLE BETWEEN DOUBLE SHAFT SEALS Class 1 - J 498 b
PLASTIC PLUG 12/24 d.p. - 14 teeth
30° Pressure angle
M14 x 24 DEEP - 4 HOLES M12 x 26 DEEP - 4 HOLES
flat root side fit
KEY
M8 x 16 DEEP
35,2 MAX
Shaft Code 2
(Keyed no SAE)
SUCTION ø 50,8 PRESSURE ø 31,7
OPERATING CHARACTERISTICS - TYPICAL [24 cSt]

Series
1000 46,0 40,5 36,0 1,4 11,7 19,9
B14 46,0 ml/rev
1500 69,0 63,5 59,0 1,9 17,6 29,5
1000 58,3 52,8 48,3 1,6 14,5 24,8
B17 58,3 ml/rev
1500 87,4 82,0 77,5 2,1 21,9 36,9
1000 63,8 58,3 53,8 1,6 15,8 27,0
B20 63,8 ml/rev
1500 95,7 90,2 85,7 2,2 23,8 40,2
1000 70,3 64,8 60,3 1,7 17,3 29,6
B22 70,3 ml/rev
1500 105,4 100,0 95,5 2,3 26,1 44,1
1000 79,3 73,8 69,3 1,8 19,3 33,2
B251) 79,3 ml/rev
1500 118,9 113,5 109,0 2,5 29,2 49,5
1000 88,8 83,3 80,12) 1,9 21,9 32,52)
B281) 88,8 ml/rev
1500 133,2 127,7 124,52) 2,8 32,7 48,52)
1000 100,0 94,5 91,32) 2,0 24,4 36,42)
B311) 100,0 ml/rev
1500 150,0 144,5 141,32) 2,8 36,5 54,42)
1) 2)

Vierzon - France
Ordering Code Series T6D*, Denison Vane Pumps
Model No. T6D* - B45 - 1 R 00 - C 1

Series M = Mobile 1 shaft seal
Modification
Series P = Mobile 2 shaft seals
Seal class
Cam ring
1 = S1 (for mineral oil)
(Delivery at 0 bar & 1500 r.p.m.)
4 = S4 (for the resistant fluids)
B14 = 71,4 l/min B35 = 166,5 l/min
5 = S5 (for mineral oil and fire resistant fluids)
B17 = 87,3 l/min B38 = 180,4 l/min
B20 = 99,0 l/min B42 = 204,0 l/min Design letter
B24 = 119,3 l/min B45 = 218,5 l/min Porting combination
B28 = 134,5 l/min B50 = 237,0 l/min 00 = standard
B31 = 147,4 l/min
Direct. of rotation (view on shaft end)
Type of shaft Type of shaft R = clockwise
M version P version L = counter-clockwise
1 = keyed (SAE C)
2 = keyed (no SAE)
3 = splined (SAE C) 3 = splined (no SAE)
4 = splined (no SAE)
T = splined (SAE J718c) P = Pressure port
S = Suction port

T6DM - B38

Power loss Ps [kW]
Shaft keyed N° 1
Load F [N]

Parker Hannifin SAS

14
Vierzon - France
Dimensions and Characteristics Series T6D*, Denison Vane Pumps
Shaft Code 1
(keyed SAE C)
6,35 MAXI
KEY
M10 X 20 DEEP
35,27 MAXI
7/16"-14UNC x 22,3 DEEP- 4 HOLES
1/2"-13UNC x 23,9 DEEP- 4 HOLES

KEY
35,27 MAXI
Shaft Code 2
Shaft Code 3 Shaft Code 4 (keyed no SAE)
SAE C Splined shaft no SAE Splined shaft
Class 1 - J498B Class 1 - J498 b SUCTION ø 50,8 PRESSURE ø 31,8
12/24 d.p. - 14 teeth 12/24 d.p. - 14 teeth
30° pressure angle 30° pressure angle Shaft torque limits [ml/rev x bar]
flat root side fit flat root side fit
Pump Shaft Vi x p max.
1 43240
2 34590
Additional T6DM shaft code T: see page 33 T6DM
3 61200
Additional T6DP version shaft see page 33
4 61200
Series
1000 47.6 38.3 32.1 1.5 12.5 20.7
B14 47.6 ml/rev
1500 71.4 62.1 55.9 2.3 18.5 30.6
1000 58.2 48.9 42.7 1.6 14.9 24.9
B17 58.2 ml/rev
1500 87.3 78.0 71.8 2.5 22.2 37.0
1000 66.0 56.7 50.5 1.7 16.8 28.0
B20 66.0 ml/rev
1500 99.0 89.7 83.5 2.8 24.9 41.7
1000 79.5 70.2 64.0 1.9 19.9 33.4
B24 79.5 ml/rev
1500 119.3 110.0 103.8 3.0 29.6 49.8
1000 89.7 80.4 74.2 2.0 22.3 37.5
B28 89.7 ml/rev
1500 134.5 125.2 119.0 3.2 33.2 55.9
1000 98.3 89.0 82.8 2.1 24.3 40.9
B31 98.3 ml/rev
1500 147.4 138.1 131.9 3.3 36.2 61.0
1000 111.0 101.7 95.5 2.3 27.3 46.0
B35 111.0 ml/rev
1500 166.5 157.2 151.0 3.5 40.7 68.7
1000 120.3 111.0 104.8 2.4 29.4 49.8
B38 120.3 ml/rev
1500 180.4 171.1 164.9 3.7 43.9 74.3
1000 136.0 126.7 120.5 2.6 33.1 56.0
B421) 136.0 ml/rev
1500 204.0 194.7 188.5 4.0 49.4 83.7
1000 145.7 136.4 130.2 2.7 35.3 59.9
B451) 145.7 ml/rev
1500 218.5 209.2 203.0 4.1 52.8 89.5
1000 158.0 148.7 145.02) 2.8 38.2 56.82)
B501) 158.0 ml/rev
1500 237.0 227.7 224.02) 4.4 57.0 85.02)
1) 2)
B42 - B45 - B50 = 2200 R.P.M. max. B50 = 210 bar max. int. Port connection can be furnished with metric threads.

Vierzon - France
Ordering Code Series T6E*, Denison Vane Pumps
Model No. T6E* - 066 - 3 R 00 - B 1

Seal class
Cam ring 1 = S1 (for mineral oil)
(Delivery at 0 bar & 1500 r.p.m.) 4 = S4 (for the resistant fluids)
042 = 198,5 l/min 062 = 295,0 l/min 5 = S5 (for mineral oil and fire resistant fluids)
045 = 213,6 l/min 066 = 319,9 l/min
Design letter
050 = 237,7 l/min 072 = 340,6 l/min
052 = 247,2 l/min Porting combination
00 = standard
Type of shaft Type of shaft
M version P version Direct. of rotation (view on shaft end)
1 = keyed (SAE CC) R = clockwise
2 = keyed (no SAE) L = counter-clockwise
3 = splined (SAE C) 3 = splined (no SAE)
4 = splined (SAE CC)
T = splined (SAE J718c)
P = Pressure port
S = Suction port

T6EM - 050

Power loss Ps [kW]
Shaft keyed N° 1
Load F [N]

Parker Hannifin SAS

16
Vierzon - France
Dimensions and Characteristics Series T6E*, Denison Vane Pumps
MOUTING TORQUE 187Nm
6,35 MAX
KEY
M10 x 20 DEEP
42,36 MAX
Shaft Code 1
5/8"-11UNC x 24 DEEP - 4 HOLES 1/2"-13UNC x 23,4 DEEP - 4 HOLES (Keyed SAE C-C)
KEY
35,27 MAX
SAE C Splined shaft SAE C-C Splined shaft
Class 1 - J498 b Class 1 - J498 b
12/24 d.p. - 14 teeth 12/24 d.p. - 17 teeth Shaft Code 2
30° pressure angle 30° pressure angle SUCTION ø 75 PRESSURE ø 37,1 (Keyed no SAE)
Shaft torque limits [ml/rev x bar]

Pump Shaft Vi x p max.
Additional T6EM shaft code T: see page 33 1 54500
Additional T6EP version shaft see page 33 2 34590
T6EM
3 61200
4 61200
Series Volumetric Speed Flow Q [l/min] Input power P [kW]
042 132,3 ml/rev 1000 132,3 122,3 115,2 3,2 32,9 55,2
1500 198,5 188,5 181,3 5,2 49,4 82,6
045 142,4 ml/rev 1000 142,4 132,4 125,3 3,4 35,3 59,2
1500 213,6 203,6 196,5 5,4 52,9 88,7
050 158,5 ml/rev 1000 158,5 148,5 141,4 3,5 39,0 65,6
1500 237,7 227,7 220,6 5,7 58,5 98,3
052 164,8 ml/rev 1000 164,8 154,8 147,7 3,6 40,5 68,2
1500 247,2 237,2 230,1 5,8 60,8 102,1
062 196,7 ml/rev 1000 196,7 186,7 179,6 4,0 47,9 80,9
1500 295,0 285,0 277,9 6,4 71,9 121,3
066 213,3 ml/rev 1000 213,3 203,3 196,2 4,2 51,8 87,6
1500 319,9 309,9 302,8 6,7 77,7 131,2
072 227,1 ml/rev 1000 227,1 217,1 210,0 4,3 55,0 93,1
1500 340,6 330,6 323,5 6,9 82,6 139,5
Port connection can be furnished with metric threads.

Vierzon - France
Ordering Code Series T6CC*, Denison Vane Pumps
Model No. T6CC* W - B22 - B08 - 1 R 00 - D 1 - 00

Series P = Mobile 2 shaft seals P1 P2 Mounting W/connection variables
Use for severe duty shaft only* P1 = 1" - S = 3" P1 = 1" - S = 2.1/2"2)
1)
Cam ring for “P1” & “P2” P2 1" 3/4" 1" 3/4"1)
(Delivery at 0 bar & 1500 r.p.m.) Code 00 01 10 11
B03 = 16,2 l/min B17 = 87,4 l/min 1)
for 46 ml/rev. max.
B05 = 25,8 l/min B20 = 95,7 l/min 2)
for 126 ml/rev. max.
B06 = 31,9 l/min B22 = 105,4 l/min The largest cartridge most be always
B08 = 39,6 l/min B25 = 118,9 l/min mounted in the front.
B10 = 51,1 l/min B28 = 133,2 l/min
B12 = 55,6 l/min B31 = 150,0 l/min Seal Class
B14 = 69,0 l/min 1 = S1 (for mineral oil)
Type of shaft Type of shaft 5 = S5 (for mineral oil and fire
M version MW severe duty resistant fluids)
1 = keyed (no SAE) *2 = keyed (SAE BB)
3 = splined (SAE BB) *R = keyed special Design letter
5 = splined (SAE B) *X = keyed special Porting combination (see page 34)
P version *W = keyed special 00 = standard
3 = splined (no SAE) *V = keyed special Direct. of rotation (view on shaft end)
4 = splined (SAE BB) *T = splined (SAE J718c) R = clockwise
6 = splined (no SAE) L = counter-clockwise

T6CCM - B22 - B22

Do not operate the pump more than 5 seconds at any speed or Double pump noise level is given with each section discharging at
viscosity if internal leakage is more than 50 % of theoretical flow. the pressure noted on the curve.
Total leakage is the sum of each section loss at its operating
conditions.

Power loss Ps [kW]
Shaft keyed N° 1
Load F [N]

Total hydrodynamic power loss is the sum of each section at its Maximum permissible axial load Fa = 800 N
operating conditions.
Parker Hannifin SAS

18
Vierzon - France
Dimensions and Characteristics Series T6CC*, Denison Vane Pumps
6,35 MAX KEY
M8 X 16 DEEP
28,22 MAX
MOUNTING TORQUE 159 Nm. MOUNTING TORQUE 61 Nm T6CCMW
3/8"-16UNC x 19 DEEP - 4 HOLES E - 4 HOLES 3/8"-16UNC x 19 DEEP - 4 HOLES Shaft Code 2
(Keyed SAE B-B)
KEY
24,53 MAX
SAE B-B Splined shaft SAE B Splined shaft
Class 1 - J498 b
Class 1 - J498 b
16/32 d.p. - 13 teeth
Shaft Code 1
16/32 d.p. - 15 teeth (Keyed no SAE)
30° pressure angle 30° pressure angle SUCTION ø C PRESSURE ø 25,4
PRESSURE ø C
Additional special shafts: see page 33

Additional T6CCMW shaft code T: see page 33
Additional T6CCP version shaft see page 33
Port Code A B C D E Shaft torque limits [ml/rev x bar]

S 3" 106,4 61,9 76,2 5/8"-11 x 28.4 deep Pump Shaft Vi x p max. P1 + P2
S 2"1/2 88,9 50,8 63,5 1/2"-13 x 23.9 deep T6CCM 1 14300
P1 1" 52,4 26,2 25,4 76,2 T6CCMW 2 21420
P2 3/4" 47,7 22,2 19,0 76,2 T6CCM 3 32670
P2 1" 52,4 26,2 25,4 74,7 T6CCM 5 20600

Pressure Volumetric Flow Q [l/min] & n = 1500 RPM Input power P [kW] & n = 1500 RPM
Series
port Displacement Vi p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar
B03 10,8 ml/rev 16,2 10,7 - 1,3 5,3 -
B05 17,2 ml/rev 25,8 20,3 15,8 1,4 7,5 12,2
B06 21,3 ml/rev 31,9 26,5 22,0 1,5 8,9 14,7
B08 26,4 ml/rev 39,6 34,1 29,6 1,6 10,7 17,7
B10 34,1 ml/rev 51,1 45,7 41,2 1,7 13,4 22,3
B12 37,1 ml/rev 55,6 50,2 45,7 1,7 14,4 24,1
B14 46,0 ml/rev 69,0 63,5 59,0 1,9 17,6 29,5
P1
B17 58,3 ml/rev 87,4 82,0 77,5 2,1 21,9 36,9
& B20 63,8 ml/rev 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 105,4 100,0 95,5 2,3 26,1 44,1
P2 B251) 79,3 ml/rev 118,9 113,5 109,0 2,5 29,2 49,5
B281) 88,8 ml/rev 133,2 127,7 124,52) 2,8 32,7 48,52)
B311) 100,0 ml/rev 15,0 144,5 141,32) 2,8 36,5 54,42)
1) 2)
- Not to use because internal leakage greater than 50% theoretical flow. Port connection can be furnished with metric threads.

Vierzon - France
Ordering Code Series T6DC*, Denison Vane Pumps
Model No. T6DC* W - B38 - B22 - 1 R 00 - C 1

Series P = Mobile 2 shaft seals P1 P2 Seal Class
Use for severe duty shaft only* 1 = S1 (for mineral oil)
Cam ring for “P1” 4 = S4 (for the resistant fluids)
(Delivery at 0 bar & 1500 r.p.m.) 5 = S5 (for mineral oil and fire
B14 = 71,4 l/min B35 = 166,5 l/min resistant fluids)
B17 = 87,3 l/min B38 = 180,4 l/min Design letter
B20 = 99,0 l/min B42 = 204,0 l/min Porting combination (see page 34)
B28 = 134,5 l/min B50 = 237,0 l/min
B31 = 147,4 l/min Direct. of rotation (view on shaft end)
R = clockwise
Cam ring for ”P2” L = counter-clockwise
B03 = 16,2 l/min B17 = 87,4 l/min Type of shaft Type of shaft
B05 = 25,8 l/min B20 = 95,7 l/min P version M version
B06 = 31,9 l/min B22 = 105,4 l/min
3 = splined (no SAE) 1 = keyed (SAE C)
B08 = 39,6 l/min B25 = 118,9 l/min 2 = keyed (no SAE)
B10 = 51,1 l/min B28 = 133,2 l/min 3 = splined (SAE C)
B12 = 55,6 l/min B31 = 150,0 l/min 4 = splined (no SAE)
B14 = 69,0 l/min MW severe duty
*5 = keyed (no SAE)
*T = splined (SAE J718c)
T6DCM - B38 - B22

viscosity if internal leakage is more than 50 % of theoretical flow. the pressure noted on the curve.
conditions.

Power loss Ps [kW]
Shaft keyed N° 1
Load F [N]

Parker Hannifin SAS

20
Vierzon - France
Dimensions and Characteristics Series T6DC*, Denison Vane Pumps
6,35 MAXI
KEY
M10 x 20 DEEP
35,27 MAXI
5/8"-11UNC x 28,5 DEEP - 4 HOLES 7/16"-14UNC x 22,3 DEEP-4 HOLES Shaft Code 1
MOUNTING TORQUE 187 Nm.3/8"-16UNC x 19 DEEP - 4 HOLES (Keyed SAE C)
KEY
35,27 MAXI
SAE C Splined shaft
Class 1 - J498 b
no SAE splined shaft
Class 1 - J498 b
Shaft Code 2
SUCTION ø 76 PRESSURE ø 31,8 (Keyed no SAE)
12/24 d.p. - 14 teeth 12/24 d.p. - 14 teeth
30° pressure angle 30° pressure angle PRESSURE ø 25
flat root side fit flat root side fit Additional T6DCM shaft code T: see page 33
Additional T6DCP version shaft see page 33
KEY
T6DCMW Shaft torque limits [ml/rev x bar]
Shaft Code 5 Pump Shaft Vi x p max. P1 + P2
(Keyed no SAE)
1 43240
2 34590
38,42 MAXI
M8 x 16 DEEP T6DCM
3 61200
4 61200
T6DCMW 5 55600
Series
B14 47,6 ml/rev 71,4 62,1 55,9 2,3 18,5 30,6
B17 58,2 ml/rev 87,3 78,0 71,8 2,5 22,2 37,0
B20 66,0 ml/rev 99,0 89,7 83,5 2,8 24,9 41,7
B24 79,5 ml/rev 119,3 110,0 103,8 3,0 29,6 49,8
P1 B28 89,7 ml/rev 134,5 125,2 119,0 3,2 33,2 55,9
B31 98,3 ml/rev 147,4 138,1 131,9 3,3 36,2 61,0
B35 111,0 ml/rev 166,5 157,2 151,0 3,5 40,7 68,7
B38 120,3 ml/rev 180,4 171,1 164,9 3,7 43,9 74,3
B422) 136,0 ml/rev 204,0 194,7 188,5 4,0 49,4 83,7
B452) 145,7 ml/rev 218,5 209,2 203,0 4,1 52,8 89,5
B502) 158,0 ml/rev 237,0 227,7 224,01) 4,4 57,0 85,01)
B03 10,8 ml/rev 16,2 10,7 - 1,3 5,3 -
B05 17,2 ml/rev 25,8 20,3 15,8 1,4 7,5 12,2
B06 21,3 ml/rev 31,9 26,5 22,0 1,5 8,9 14,7
B08 26,4 ml/rev 39,6 34,1 29,6 1,6 10,7 17,7
B10 34,1 ml/rev 51,1 45,7 41,2 1,7 13,4 22,3
B12 37,1 ml/rev 55,6 50,2 45,7 1,7 14,4 24,1
P2
B14 46,0 ml/rev 69,0 63,5 59,0 1,9 17,6 29,5
B17 58,3 ml/rev 87,4 82,0 77,5 2,1 21,9 36,9
B20 63,8 ml/rev 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 105,4 100,0 95,5 2,3 26,1 44,1
B25 79,3 ml/rev 118,9 113,5 109,0 2,5 29,2 49,5
B28 88,8 ml/rev 133,2 127,7 124,51) 2,8 32,7 48,51)
B31 100,0 ml/rev 150,0 144,5 141,31) 2,8 36,5 54,41)
1) 2)
B28 - B31 - B50 = 210 bar max. int. B42 - B45 - B50 = 2200 R.P.M. max
- Not to use because internal leakage greater than 50% theoretical flow Port connection can be furnished with metric threads.

Vierzon - France
Ordering Code Series T6EC*, Denison Vane Pumps
Model No. T6EC* - 066 - B22 - 1 R 00 - C 1 -

Series P = Mobile 2 shaft seals P1 P2
Seal Class
Cam ring for “P1” 1 = S1 (for mineral oil)
(Delivery at 0 bar & 1500 r.p.m.) 4 = S4 (for the resistant fluids)
042 = 198,5 l/min 062 = 295,0 l/min 5 = S5 (for mineral oil and fire resistant fluids)
045 = 213,6 l/min 066 = 319,9 l/min
050 = 237,7 l/min 072 = 340,6 l/min Design letter
052 = 247,2 l/min Porting combination (see page 34)
Cam ring for ”P2” 00 = standard
(Delivery at 0 bar & 1500 r.p.m.) Direct. of rotation (view on shaft end)
B03 = 16,2 l/min B17 = 87,4 l/min R = clockwise
B05 = 25,8 l/min B20 = 95,7 l/min L = counter-clockwise
B10 = 51,1 l/min B28 = 133,2 l/min 3 = splined (non SAE) 1 = keyed (SAE CC)
B12 = 55,6 l/min B31 = 150,0 l/min 2 = keyed (no SAE)
B14 = 69,0 l/min 3 = splined (SAE C)

T6ECM - 050 - B22

viscosity if internal leakage is more than 50% of theoretical flow. the pressure noted on the curve.
conditions.

Power loss Ps [kW]
Load F [N]
Shaft keyed N° 1

Parker Hannifin SAS

22
Vierzon - France
Dimensions and Characteristics Series T6EC*, Denison Vane Pumps
6,35 MAX
KEY
M10 X 20 DEEP
42,36 MAX
MOUNTING TORQUE 187 Nm. MOUNTING TORQUE 58 Nm.
Shaft Code 1
(Keyed SAE C-C)
5/8"-11UNC x 29,5 DEEP - 4 HOLES 1/2"-13UNC x 23,4 DEEP - 4 HOLES
3/8"-16 UNC x 19 DEEP - 4 HOLES
KEY
35,27 MAX
Shaft Code 2
(Keyed no SAE)
SAE C Splined shaft SAE C-C Splined shaft
12/24 d.p. - 14 teeth 12/24 d.p. - 17 teeth
30° pressure angle 30° pressure angle
flat root side fit flat root side fit PRESSURE ø 25 Shaft torque limits [ml/rev x bar]
Pump Shaft Vi x p max. P1 + P2
Additional T6ECM shaft code T: see page 33 1 72300
Additional T6ECP version shaft see page 33 2 34590
T6ECM
3 61200
OPERATING CHARACTERISTICS - TYPICAL [24 cSt] 4 76300
Series
042 132,3 ml/rev 198,5 188,5 181,3 5,2 49,4 82,6
045 142,4 ml/rev 213,6 203,6 196,5 5,4 52,9 88,7
P1 050 158,5 ml/rev 237,7 227,7 220,6 5,7 58,5 98,3
052 164,8 ml/rev 247,2 237,2 230,1 5,8 60,8 102,1
062 196,7 ml/rev 295,0 285,0 277,9 6,4 71,9 121,3
066 213,3 ml/rev 319,9 309,9 302,8 6,7 77,7 131,2
072 227,1 ml/rev 340,6 330,6 323,5 6,9 82,6 139,5
B03 10,8 ml/rev 16,2 10,7 - 1,3 5,3 -
B05 17,2 ml/rev 25,8 20,3 15,8 1,4 7,5 12,2
B06 21,3 ml/rev 31,9 26,5 22,0 1,5 8,9 14,7
B08 26,4 ml/rev 39,6 34,1 29,6 1,6 10,7 17,7
B10 34,1 ml/rev 51,1 45,7 41,2 1,7 13,4 22,3
B12 37,1 ml/rev 55,6 50,2 45,7 1,7 14,4 24,1
P2 B14 46,0 ml/rev 69,0 63,5 59,0 1,9 17,6 29,5
B17 58,3 ml/rev 87,4 82,0 77,5 2,1 21,9 36,9
B20 63,8 ml/rev 95,7 90,2 85,7 2,2 23,8 40,2
B22 70,3 ml/rev 105,4 100,0 95,5 2,3 26,1 44,1
B25 79,3 ml/rev 118,9 113,5 109,0 2,5 29,2 49,5
B28 88,8 ml/rev 133,2 127,7 124,51) 2,8 32,7 48,51)
B31 100,0 ml/rev 150,0 144,5 141,31) 2,8 36,5 54,41)
1)
B28 - B31 = 210 bar max. int. - Not to use because internal leakage greater than 50% theoretical flow
Port connection can be furnished with metric threads.

Vierzon - France
Ordering Code Series T6ED*, Denison Vane Pumps
Model No. T6ED* - 066 - B38 - 1 R 00 - C 1 -

Series M = Mobile 1 shaft seal
P1 P2 Modification
Seal Class
Cam ring for “P1”
1 = S1 (for mineral oil)
042 = 198,5 l/min 062 = 295,0 l/min
045 = 213,6 l/min 066 = 319,9 l/min
050 = 237,7 l/min 072 = 340,6 l/min Design letter
052 = 247,2 l/min Porting combination (see page 34)
Cam ring for ”P2” 00 = standard
(Delivery at 0 bar & 1500 r.p.m.) Direct. of rotation (view on shaft end)
B28 = 134,5 l/min B50 = 237,0 l/min 3 = splined (no SAE) 1 = keyed (SAE CC)
B31 = 147,4 l/min 2 = keyed (no SAE)
3 = splined (SAE C)
4 = splined SAE CC)

T6EDM - 050 - B38

Total leakage is the sum of each section loss at its operating Double pump noise level is given with each section discharging at
conditions. the pressure noted on the curve.

Power loss Ps [kW]
Shaft keyed N° 1
Load F [N]

Parker Hannifin SAS

24
Vierzon - France
Dimensions and Characteristics Series T6ED*, Denison Vane Pumps
6,35 MAX
KEY
M10X20 DEEP
42,36 MAX
MOUNTING TORQUE 187 Nm. Shaft Code 1
7/16"-14 UNC x 24 DEEP - 4 HOLES 5/8"-11UNC x 30 DEEP - 4 HOLES 1/2"-13UNC x 23,4 DEEP - 4 HOLES (Keyed SAE C-C)
KEY
35,27 MAX
Shaft Code 3 Shaft Code 4 Shaft Code 2
(Keyed no SAE)
SAE C Splined shaft SAE C-C Splined shaft SUCTION ø101.6 PRESSURE ø37,1
12/24 d.p. - 14 teeth 12/24 d.p. - 17 teeth PRESSURE ø29.5
30° pressure angle 30° pressure angle
Shaft torque limits [ml/rev x bar]

Pump Shaft Vi x p max. P1 + P2
1 72300
2 34590
Additional T6EDM shaft code T: see page 33 T6EDM
3 61200
Additional T6EDP version shaft see page 33
4 68500
Pressure Volumetric Flow Q [l/min] & n = 1500 RPM Flow Q [l/min] & n = 1500 RPM
Series
042 132,3 ml/rev 198,5 188,5 181,3 5,2 49,4 82,6
045 142,4 ml/rev 213,6 203,6 196,5 5,4 52,9 88,7
P1 050 158,5 ml/rev 237,7 227,7 220,6 5,7 58,5 98,3
052 164,8 ml/rev 247,2 237,2 230,1 5,8 60,8 102,1
062 196,7 ml/rev 295,0 285,0 277,9 6,4 71,9 121,3
066 213,3 ml/rev 319,9 309,9 302,8 6,7 77,7 131,2
072 227,1 ml/rev 340,6 330,6 323,5 6,9 82,6 139,5
B14 47,6 ml/rev 71,4 62,1 55,9 2,3 18,5 30,6
B17 58,2 ml/rev 87,3 78,0 71,8 2,5 22,2 37,0
B20 66,0 ml/rev 99,0 89,7 83,5 2,8 24,9 41,7
B24 79,5 ml/rev 119,3 110,0 103,8 3,0 29,6 49,8
P2 B28 89,7 ml/rev 134,5 125,2 119,0 3,2 33,2 55,9
B31 98,3 ml/rev 147,4 138,1 131,9 3,3 36,2 61,0
B35 111,0 ml/rev 166,5 157,2 151,0 3,5 40,7 68,7
B38 120,3 ml/rev 180,4 171,1 164,9 3,7 43,9 74,3
B42 136,0 ml/rev 204,0 194,7 188,5 4,0 49,4 83,7
B45 145,7 ml/rev 218,5 209,2 203,0 4,1 52,8 89,5
B50 158,0 ml/rev 237,0 227,7 224,01) 4,4 57,0 85,01)
1)
B50 = 210 bar max. int. Port connection can be furnished with metric threads.

Vierzon - France
Ordering Code and Characteristics Series T6DCCM, Denison Vane Pumps
Model No. T6DCCM - B38 - B28 - B08 - 1 R 00 - B 1 - 00

Series Modification
P1 P2 P3
Cam ring for “P1” Mounting W/connection variables
(Delivery at 0 bar & 1500 r.p.m.) Type UNC Metric
B14 = 71,4 l/min B35 = 166,5 l/min P3 1" 3/4" 1" 3/4"
B17 = 87,3 l/min B38 = 180,4 l/min Code 00 01 M0 M1
B20 = 99,0 l/min B42 = 204,0 l/min
B24 = 119,3 l/min B45 = 218,5 l/min Seal class
B28 = 134,5 l/min B50 = 237,0 l/min 1 = S1 (for mineral oil)
B31 = 147,4 l/min 4 = S4 (for the resistant fluids)
Cam ring for ”P2” & “P3”
(Delivery at 0 bar & 1500 r.p.m.) Design letter
B03 = 16,2 l/min B17 = 87,4 l/min Porting combination (see pages 34 - 35)
B06 = 31,9 l/min B22 = 105,4 l/min Direct. of rotation (view on shaft end)
B12 = 55,6 l/min B31 = 150,0 l/min
B14 = 69,0 l/min Type of shaft
1 = keyed (no SAE)
2 = keyed (SAE CC)
3 = splined (SAE C)
6 = splined (no SAE)

Series
B14 47.6 ml/rev 71.4 62.1 55.9 2.3 18.5. 30.6
B17 58.2 ml/rev 87.3 78.0 71.8 2.5 22.2 37.0
B20 66.0 ml/rev 99.0 89.7 83.5 2.8 24.9 41.7
B24 79.5 ml/rev 119.3 110.0 103.8 3.0 29.6 49.8
B28 89.7 ml/rev 134.5 125.2 119.0 3.2 33.2 55.9
P1 B31 98.3 ml/rev 147.4 138.1 131.9 3.3 36.2 61.0
B35 111.0 ml/rev 166.5 157.2 151.0 3.5 40.7 68.7
B38 120.3 ml/rev 180.4 171.1 164.9 3.7 43.9 74.3
B422) 136.0 ml/rev 204.0 194.7 188.5 4.0 49.4 83.7
B452) 145.7 ml/rev 218.5 209.2 203.0 4.1 52.8 89.5
B502) 158.0 ml/rev 237.0 227.7 224.01) 4.4 57.0 85.01)
B03 10.8 ml/rev 16.2 10.7 - 1.3 5.3 -
B05 17.2 ml/rev 25.8 20.3 15.8 1.4 7.5 12.2
B06 21.3 ml/rev 31.9 26.5 22.0 1.5 8.9 14.7
B08 26.4 ml/rev 39.6 34.1 29.6 1.6 10.7 17.7
P2 B10 34.1 ml/rev 51.1 45.7 41.2 1.7 13.4 22.3
& B12 37.1 ml/rev 55.6 50.2 45.7 1.7 14.4 24.1
B14 46.0 ml/rev 69.0 63.5 59.0 1.9 17.6 29.5
P3
B17 58.3 ml/rev 87.4 82.0 77.5 2.1 21.9 36.9
B20 63.8 ml/rev 95.7 90.2 85.7 2.2 23.8 40.2
B22 70.3 ml/rev 105.4 100.0 95.5 2.3 26.1 44.1
B25 79.3 ml/rev 118.9 113.5 109.0 2.5 29.2 49.5
B28 88.8 ml/rev 133.2 127.7 124.51) 2.8 32.7 48.51)
B31 100.0 ml/rev 150.0 144.5 141.31) 2.8 36.5 54.41)
1) 2)
B28 - B31 - B50 = 210 bar max. int. B42 - B45 - B50 = 2200 R.P.M. max
- Not to use because internal leakage greater than 50% theoretical flow
Parker Hannifin SAS

26
Vierzon - France
Dimensions
6,35 MAXI
KEY
Catalogue HY29-0002/UK
Shaft Code 4
SAE C-C Splined shaft
Class 1 - J498 b
34,6 MAXI
12/24 d.p. - 17 teeth
30° pressure angle
Shaft Code 1 flat root side fit
MOUNTING TORQUE 187 Nm. MOUNTING TORQUE 68 Nm. 7/16"-14 UNC x 22,3 DEEP - 4 HOLES (Keyed no SAE)
3/8"-16 UNC x 19 DEEP - 4 HOLES 5/8"-11 UNC x 30 DEEP - 4 HOLES
(M10 x 19 DEEP-METRIC VERSION) (M12 x 22,3 DEEP-METRIC VERSION)
(M16 x 30 DEEP-METRIC VERSION)
3/8"-16 UNC x 19 DEEP - 4 HOLES
(M10 x 19 DEEP-METRIC VERSION)
KEY
27
M10 x 20 DEEP
42,27 MAX
Shaft Code 6
Shaft Code 3 No SAE Splined shaft
SAE C Splined shaft Class 1 - J498 b
Class 1 - J498 b 12/24 d.p. - 14 teeth
12/24 d.p. - 14 teeth 30° pressure angle
30° pressure angle Shaft Code 2 flat root side fit
flat root side fit PRESSURE ø C (Keyed SAE C-C)
Hydraulic Pumps, Fixed

PRESSURE ø 25
MOUNTING TOURQUE 187 Nm.
Shaft torque limits [ml/rev x bar] Alternate port

Pump Shaft Vi x p max. P1 + P2 + P3 Shaft Vi x p max. P1 + P2 + P3 Port Code A B C
Vierzon - France
1 43240 3 61200 P3 00 & M0 52.4 26.2 25.4
T6DCCM
Parker Hannifin SAS

2 66500 4 66500 P3 01 & M1 47.6 22.2 19.0
Series T6DCCM, Denison Vane Pumps

Technical Data Series T6DCCM, Denison Vane Pumps

T6DCCM - B38 - B22 - B22


Total leakage is the sum of each section loss at its operating Triple pump noise level is given with each section discharging at the
conditions. pressure noted on the curve.
Shaft keyed N° 1
Power loss Ps [kW]
Load F [N]
Parker Hannifin SAS

28
Vierzon - France
Technical Data Series T6EDC*, Denison Vane Pumps

T6EDCM - 062 - B35 - B17


Total leakage is the sum of each section loss at its operating Triple pump noise level is given with each section discharging at the
conditions. pressure noted on the curve.

Power loss Ps [kW]
Load F [N]


Vierzon - France
SHAFT CODE 1
(Keyed G45N- ISO 3019-2)
Dimensions
48,5 MAX
MOUNTING TORQUE
M12 x 24 DEEP
54 Nm.
MOUNTING TORQUE: 190 Nm.
MOUNTING TORQUE: 300 Nm. M12 x 20 DEEP
30
M12 x 24 DEEP- 4 HOLES M12 x 30 DEEP- 4 HOLES
M10 x 19 DEEP- 4 HOLES M16 x 30 DEEP- 4 HOLES
SHAFT CODE 3
SAE D & E Splined shaft
Class 1 - J498 b
8/16 d.p. - 13 teeth
Vierzon - France
Alternate port
30° pressure angle
Port Code A B C flat root side fit
Parker Hannifin SAS

PRESSURE ø C PRESSURE ø 31,8 SUCTION ø 101,6 PRESSURE ø 31,8
P3 0 52,4 26,2 25,4
Series T6EDCM, Denison Vane Pumps
P3 1 47,6 22,2 19,0

KEY
Dimensions
49,3 MAX
MOUNTING TORQUE: 190 Nm.

1/2"-13 UNC x 24 DEEP
MOUNTING TORQUE: 300 Nm. 1/2"-13 UNC x 20 DEEP
SHAFT CODE 2
MOUNTING TORQUE
(Keyed SAE D & E)
54 Nm.
31
7/16"-14 UNC x 24 DEEP- 4 HOLES 1/2"-13 UNC x 30 DEEP- 4 HOLES
3/8"-16 UNC x 19 DEEP- 4 HOLES 5/8"-11 UNC x 30 DEEP- 4 HOLES

SHAFT CODE 3
SAE D & E Splined shaft
Class 1 - J498 b
8/16 d.p. - 13 teeth
Alternate port 30° pressure angle
flat root side fit
Vierzon - France
Port Code A B C
PRESSURE ø C PRESSURE ø 31,8 SUCTION ø 101,6 PRESSURE ø 31,8
Parker Hannifin SAS

P3 0 52,4 26,2 25,4
Series T6EDCS, Denison Vane Pumps
P3 1 47,6 22,2 19,0

Ordering Code and Characteristics Series T6EDC*, Denison Vane Pumps
T6EDCS
Model No. T6EDCM - 062 - B35 - B17 - 1 R 00 - A 1 - P 0 -
Series Modification
P1 P2 P3
Cam ring for “P1” Mounting W/connection variables
(Delivery at 0 bar & 1500 r.p.m.) 0 = P3 = 1" SAE
042 = 198,5 l/min 062 = 295,0 l/min 1 = P3 = 3/4" SAE
045 = 213,6 l/min 066 = 319,9 l/min Options
050 = 237,7 l/min 072 = 340,6 l/min F = Standard
052 = 247,2 l/min P = 4 holes for external support
Cam ring for “P2” Seal class
B17 = 87,3 l/min B38 = 180,4 l/min 5 = S5 (for mineral oil and fire resistant fluids)
B20 = 99,0 l/min B42 = 204,0 l/min
Design letter
B24 = 119,3 l/min B45 = 218,5 l/min
B28 = 134,5 /min B50 = 237,0 l/min Porting combination (see pages 34 - 35)
B31 = 147,4 l/min 00 = standard
Cam ring for “P3” Direct. of rotation (view on shaft end)
(Delivery at 0 bar & 1500 r.p.m.) R = clockwise
B05 = 25,8 l/min B20 = 95,7 l/min Type of shaft
B06 = 31,9 l/min B22 = 105,4 l/min 1 = keyed (G45N - ISO 3019-2) (T6EDCM)
B08 = 39,6 l/min B25 = 118,9 l/min 2 = keyed (SAE D & E) (T6EDCS)
B10 = 51,1 l/min B28 = 133,2 l/min 3 = splined (SAE D & E) (T6EDCM-T6EDCS)
B12 = 55,6 l/min B31 = 150,0 l/min
B14 = 69,0 l/min
Pressure Series Volumetric Flow Q [l/min] & n = 1500 RPM Input power P [kW] & n = 1500 RPM
042 132.3 ml/rev 198.5 188.5 181.3 5.2 49.4 82.6
045 142.4 ml/rev 213.6 203.6 196.5 5.4 52.9 88.7
050 158.5 ml/rev 237.7 227.7 220.6 5.7 58.5 98.3
P1
052 164.8 ml/rev 247.2 237.2 230.1 5.8 60.8 102.1
062 196.7 ml/rev 295.0 285.0 277.9 6.4 71.9 121.3
066 213.3 ml/rev 319.9 309.9 302.8 6.7 77.7 131.2
072 227.1 ml/rev 340.6 330.6 323.5 6.9 82.6 139.5
B14 47.6 ml/rev 71.4 62.1 55.9 2.3 18.5 30.6
B17 58.2 ml/rev 87.3 78.0 71.8 2.5 22.2 37.0
B20 66.0 ml/rev 99.0 89.7 83.5 2.8 24.9 41.7
B24 79.5 ml/rev 119.3 110.0 103.8 3.0 29.6 49.8
P2 B28 89.7 ml/rev 134.5 125.2 119.0 3.2 33.2 55.9
B31 98.3 ml/rev 147.4 138.1 131.9 3.3 36.2 61.0
B35 111.0 ml/rev 166.5 157.2 151.0 3.5 40.7 68.7
B38 120.3 ml/rev 180.4 171.1 164.9 3.7 43.9 74.3
B42 136.0 ml/rev 204.0 194.7 188.5 4.0 49.4 83.7
B45 145.7 ml/rev 218.5 209.2 203.0 4.1 52.8 89.5
B50 158.0 ml/rev 237.0 227.7 224.01) 4.4 57.0 85.01)
B03 10.8 ml/rev 16.2 10.7 - 1.3 5.3 -
B05 17.2 ml/rev 25.8 20.3 15.8 1.4 7.5 12.2
B06 21.3 ml/rev 31.9 26.5 22.0 1.5 8.9 14.7
B08 26.4 ml/rev 39.6 34.1 29.6 1.6 10.7 17.7
B10 34.1 ml/rev 51.1 45.7 41.2 1.7 13.4 22.3
B12 37.1 ml/rev 55.6 50.2 45.7 1.7 14.4 24.1
B14 46.0 ml/rev 69.0 63.5 59.0 1.9 17.6 29.5
P3
B17 58.3 ml/rev 87.4 80.0 77.5 2.1 21.9 36.9
B20 63.8 ml/rev 95.7 90.2 85.7 2.2 23.8 40.2
B22 70.3 ml/rev 105.4 100.0 95.5 2.3 26.1 44.1
B25 79.3 ml/rev 118.9 113.5 109.0 2.5 29.2 49.5
B28 88.8 ml/rev 133.2 127.7 124.51) 2.8 32.7 48.51)
B31 100.0 ml/rev 150.0 144.5 141.31) 2.8 36.5 54.41)
1)
B28 - B31 - B50 = 210 bar max. int. - Not to use because internal leakage greater than 50% theoretical flow
Parker Hannifin SAS

32
Vierzon - France
Additional Shafts Series T6 Mobile, Denison Vane Pumps
ADDITIONAL P VERSION
T6CCP T6CCP T6CCP

Shaft torque limits Shaft torque limits Shaft torque limits
20600 [ml/rev x bar] 32670 [ml/rev x bar] 32670 [ml/rev x bar]

no SAE splined shaft SAE B-B splined shaft no SAE splined shaft
Class 1 - J498b Class 1 - J498b Class 1 - J498b
16/32 d.p. - 13 teeth 16/32 d.p. - 15 teeth 12/24 d.p. - 14 teeth
30° pressure angle 30° pressure angle 30° pressure angle
flat root side fit flat root side fit flat root side fit
T6DP T6DCP T6EP - T6ECP

T6EDP
Shaft torque limits
61200 [ml/rev x bar]

no SAE splined shaft no SAE splined shaft no SAE splined shaft
Class 1 - J498b Class 1 - J498b Class 1 - J498b
12/24 d.p. - 14 teeth 12/24 d.p. - 14 teeth 12/24 d.p. - 14 teeth
30° pressure angle 30° pressure angle 30° pressure angle
flat root side fit flat root side fit flat root side fit
* Drain hole between double shaft seals.
ADDITIONAL SHAFT CODE T : 540 RPM POWER TAKE-OFF - SAE J718C FOR FARM TRACTORS
Shaft torque limits
T6CCMW - 32670 [ml/rev x bar]
T6DCMW - 66600 [ml/rev x bar]
T6DM T6EM - T6ECM - T6EDM - 70400 [ml/rev x bar]
ADDITIONAL SPECIAL T6CCMW SHAFTS

Shaft Code R Shaft Code V Shaft Code X Shaft Code W
Shaft torque limits Shaft torque limits Shaft torque limits Shaft torque limits
18100 [ml/rev x bar] 32670 [ml/rev x bar] 25400 [ml/rev x bar] 32670 [ml/rev x bar]
KEY KEY KEY KEY

28,22 MAXI
35,27 MAXI
35,40 MAXI
M8 x 16 DEEP
M8 x 16 DEEP
M8 x 16 DEEP
29,85 MAXI
M12 x 24 DEEP

Vierzon - France
Porting Diagrams Series T6 Mobile, Denison Vane Pumps
T6CC* - T6DC* - T6EC*
T6ED*
T6DCCM - T6EDC*
Parker Hannifin SAS

34
Vierzon - France
Porting Diagrams Series T6 Mobile, Denison Vane Pumps
T6DCCM - T6EDC*

Vierzon - France
Parker Worldwide
AE – UAE, Dubai FR – France, Contamine s/Arve RO – Romania, Bucharest

Tel: +971 4 8127100 Tel: +33 (0)4 50 25 80 25 Tel: +40 21 252 1382
parker.me@parker.com parker.france@parker.com parker.romania@parker.com
AR – Argentina, Buenos Aires GR – Greece, Athens RU – Russia, Moscow
Tel: +54 3327 44 4129 Tel: +30 210 933 6450 Tel: +7 495 645-2156
parker.greece@parker.com parker.russia@parker.com
AT – Austria, Wiener Neustadt
Tel: +43 (0)2622 23501-0 HK – Hong Kong SE – Sweden, Spånga
parker.austria@parker.com Tel: +852 2428 8008 Tel: +46 (0)8 59 79 50 00
parker.sweden@parker.com
AT – Eastern Europe, HU – Hungary, Budapest
Wiener Neustadt Tel: +36 1 220 4155 SG – Singapore
Tel: +43 (0)2622 23501 900 parker.hungary@parker.com Tel: +65 6887 6300
parker.easteurope@parker.com
IE – Ireland, Dublin SK – Slovakia, Banská Bystrica
AU – Australia, Castle Hill Tel: +353 (0)1 466 6370 Tel: +421 484 162 252
Tel: +61 (0)2-9634 7777 parker.ireland@parker.com parker.slovakia@parker.com
AZ – Azerbaijan, Baku IN – India, Mumbai SL – Slovenia, Novo Mesto
Tel: +994 50 2233 458 Tel: +91 22 6513 7081-85 Tel: +386 7 337 6650
parker.azerbaijan@parker.com parker.slovenia@parker.com
IT – Italy, Corsico (MI)
BE/LU – Belgium, Nivelles Tel: +39 02 45 19 21 TH – Thailand, Bangkok
Tel: +32 (0)67 280 900 parker.italy@parker.com Tel: +662 717 8140
parker.belgium@parker.com
JP – Japan, Fujisawa TR – Turkey, Istanbul
BR – Brazil, Cachoeirinha RS Tel: +(81) 4 6635 3050 Tel: +90 216 4997081
Tel: +55 51 3470 9144 parker.turkey@parker.com
KR – South Korea, Seoul
BY – Belarus, Minsk Tel: +82 2 559 0400 TW – Taiwan, Taipei
Tel: +375 17 209 9399 Tel: +886 2 2298 8987
KZ – Kazakhstan, Almaty
parker.belarus@parker.com
Tel: +7 7272 505 800 UA – Ukraine, Kiev
CA – Canada, Milton, Ontario parker.easteurope@parker.com Tel +380 44 494 2731
Tel: +1 905 693 3000 parker.ukraine@parker.com
LV – Latvia, Riga
CH – Switzerland, Etoy Tel: +371 6 745 2601 UK – United Kingdom,
Tel: +41 (0) 21 821 02 30 parker.latvia@parker.com Warwick
parker.switzerland@parker.com Tel: +44 (0)1926 317 878
MX – Mexico, Apodaca
parker.uk@parker.com
CL – Chile, Santiago Tel: +52 81 8156 6000
Tel: +56 2 623 1216 US – USA, Cleveland
MY – Malaysia, Shah Alam
(industrial)
CN – China, Shanghai Tel: +60 3 7849 0800
Tel: +1 216 896 3000
Tel: +86 21 2899 5000
NL – The Netherlands,
US – USA, Lincolnshire
CZ – Czech Republic, Klecany Oldenzaal
(mobile)
Tel: +420 284 083 111 Tel: +31 (0)541 585 000
Tel: +1 847 821 1500
parker.czechrepublic@parker.com parker.nl@parker.com
VE – Venezuela, Caracas
DE – Germany, Kaarst NO – Norway, Ski
Tel: +58 212 238 5422
Tel: +49 (0)2131 4016 0 Tel: +47 64 91 10 00
parker.germany@parker.com parker.norway@parker.com ZA – South Africa,
Kempton Park
DK – Denmark, Ballerup NZ – New Zealand, Mt Wellington
Tel: +27 (0)11 961 0700
Tel: +45 43 56 04 00 Tel: +64 9 574 1744
HYGE Ed. 2009-07-01
parker.southafrica@parker.com
parker.denmark@parker.com
PL – Poland, Warsaw
ES – Spain, Madrid Tel: +48 (0)22 573 24 00
Tel: +34 902 330 001 parker.poland@parker.com
parker.spain@parker.com
PT – Portugal, Leca da Palmeira
European Product Information Centre
FI – Finland, Vantaa Tel: +351 22 999 7360 Free phone: 00 800 27 27 5374
Tel: +358 (0)20 753 2500 parker.portugal@parker.com (from AT, BE, CH, CZ, DE, DK, EE, ES, FI,
parker.finland@parker.com FR, IE, IL, IS, IT, LU, MT, NL, NO, PL, PT, RU,
SE, UK, ZA)
© 2009 Parker Hannifin Corporation. All rights reserved. Catalogue HY29-0002/UK. XM 07/2009 PC
Parker Hannifin Ltd.

Tachbrook Park Drive
Tachbrook Park, Warwick CV34 6TU
United Kingdom
Tel.: +44 (0) 1926 317 878
Fax: +44 (0) 1926 317 855
www.parker.com Your local authorized Parker distributor

Untitled

Uploaded by

Copyright:

Available Formats

Untitled

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Untitled

Uploaded by

Copyright:

Available Formats

䐀椀猀琀

T6CM Ordering code & Technical data............................................................................10

T6CP Ordering code & Technical data............................................................................12

T6D* Ordering code & Technical data............................................................................14

T6E* Ordering code & Technical data............................................................................16

T6CC* Ordering code & Technical data............................................................................18

T6DC* Ordering code & Technical data............................................................................20

T6EC* Ordering code & Technical data............................................................................22

T6DCCM Ordering code & Operating characteristics...........................................................26

T6EDC* Technical data........................................................................................................29

Parker Hannifin SAS

3 Parker Hannifin SAS

Theoretical Maximum Speed Maximum Pressure

HF-0, HF2 = Antiwear Petroleum Base

Parker Hannifin SAS

Cartridge Speed RPM

5 Parker Hannifin SAS

CALCULATION To resolve Performances required

ROUTINE AND EXAMPLE Routine : Example :

3. Theoretical flow of this pump 46 x 1500

4. Find Qper. leakage function of T6CM (page 10) : Qper. = 5 l/min at

5. Available flow Q = Qtheo. - Qper. Q = 69 - 5 = 64 l/min

6. Theoretical input power 69 x 150

7. Find ps hydrodynamic power loss T6CM (page10) : Ps at 1500 R.P.M.,

8. Calculation of necessary input

These calculation steps must be followed for each application.

Average Pressure Example : T6CM - B14

cycle Duty cycle 4 min. at 275 bar

Parker Hannifin SAS

Pilot recess as required

Ball bearing hold

Pin cavity is at a steady

Lub side holes lubricate Discharge ramp

7 Parker Hannifin SAS

RECOMMENDED FLUIDS Petroleum based antiwear R & O fluids.

Minimum fluid temperature (θ) °C

WATER CONTAMINATION IN Maximum acceptable content of water.

Parker Hannifin SAS

9 Parker Hannifin SAS

Model No. T6CM - B22 - 1 R 00 - C 1

Series M = Mobile 1 shaft seal Modification

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

Pressure p [bar] Pressure p [bar]

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Pressure p [bar] Speed n [RPM]

Parker Hannifin SAS

MOUNTING TORQUE 159 Nm.

Volumetric Speed Flow Q [l/min] Input power P [kW]

11 Parker Hannifin SAS

Model No. T6CP - B22 - 2 R 00 - A 1

Series P = Mobile 2 shaft seals Modification

INTERNAL LEAKAGE (TYPICAL) NOISE LEVEL (TYPICAL)

Pressure p [bar] Pressure p [bar]

POWER LOSS HYDROMECHANICAL (TYPICAL) PERMISSIBLE RADIAL LOAD

Pressure p [bar] Speed n [RPM]

Maximum permissible axial load Fa = 800 N

Parker Hannifin SAS

MOUNTING TORQUE : 159 Nm

OPERATING CHARACTERISTICS - TYPICAL [24 cSt]

13 Parker Hannifin SAS