Ritewing ESC Manual PDF
Ritewing ESC Manual PDF
Ritewing ESC Manual PDF
Important Precautions
Brake Mode
Timing Mode
Acceleration
Battery Type
Cut-off Voltage
Cut-off Type
Motor Rotation Direction
Medium
Automatic
Medium
Li-Ion/Li-Po
Medium
Slow Down
Rightward
Features
Excellent startup performance, great throttle linear and quick throttle response,
excellent low-speed performance.
Separate voltage regulator IC for MCU (Micro Controller Unit), high capability
of anti-interference.
Low-voltage protection, block-rotation protection and signal lose protection, etc.
All these functions can effectively prolong ESC service life.
Programmable by Trx or by a programming card (optional). Program-Card
has a simple and visual surface to conveniently change parameters at any time anywhere.
Specification:
Model No.
Current
BEC
Li-Ion/Li-Po LiFe
NIXX
12A-LBEC
12A
5V/2A
23
24
610
20A-LBEC
20A
5V/2A
23
24
610
25A-LBEC
25A
5V/2A
23
24
610
30A-LBEC
30A
5V/2A
23
24
610
35A-LBEC
35A
5V/2A
23
24
610
40A-LBEC
40A
5V/3A
23
24
610
45A-LBEC
45A
5V/3A
23
24
610
20A-SBEC
20A
5.5V/3A
24
25
616
25A-SBEC
25A
5.5V/3A
24
25
616
30A-SBEC
30A
5.5V/3A
24
25
616
35A-SBEC
35A
5.5V/3A
24
25
616
40A-SBEC
40A
5.5V/6A
26
27
616
45A-SBEC
40A
5.5V/6A
26
27
616
60A-SBEC
60A
5.5V/6A
26
27
616
65A-SBEC
65A
5.5V/6A
26
27
616
70A-SBEC
70A
5.5V/6A
26
27
616
80A-SBEC
110A
5.5V/6A
26
27
616
100A-SBEC
110A
5.5V/6A
26
27
616
150A-SBEC
150A
5.5V/6A
26
27
616
40A-OPTO
40A
NO
26
27
616
60A-OPTO
60A
NO
26
27
616
70A-OPTO
70A
NO
26
27
616
110A-OPTO
110A
NO
26
27
616
100A-HV
100A
NO
310
312
830
200A-HV
200A
NO
310
312
830
NOTE: BEC--Battery Eliminator Circuit; OPTO--NO BEC; HV--High Voltage
LBEC--Linear
mode
Factory Default
Value
BEC; SBEC--Switch mode BEC
Safe start-up. The motor wont be started no matter which position the throttle
stick is on when battery connected.
Motor rotating direction can be changed by exchanging two of three wires from
ESC or setting by the Prog-Card.
Low: softrecommended for motors of 2-8 poles motors and inrunner motors
Note: When the timing mode is saved, please adjust the motor on the ground
before the flight.
3. Acceleration
High: fast acceleration or deceleration of motor
Medium: acceleration or deceleration at middle speed
Low: slow acceleration or deceleration
4. Battery type
Ni-XX: Ni-Cd & Ni-MH
Li-XX: Li-ion & Li-polymer
Li-Fe Battery
Program parameters by Prog-card (For OPTO ESC,please connect the 4-6 V battery pack to Prog-card.) :
Connection as below:
By using A Prog-card, the above functions can be programmed quickly and simply.
1. Put the six jumpers to the required positions.
2. Plug JR connector of ESC to the specified socket on Prog-Card (orange wire-Signal, brown wire-Negative (-), red wire-Positive (+)).
3. Connect the motor to the ESC and connect ESC to power.
4. 1 will be heard in a second, means your setting has been saved ( will not be heard if there is no change of parameters).
5. Disconnect the power pack (For OPTO ESC, disconnect the Prog-Card to its battery pack).
Programmable parameters by Prog-Card:
1. Brake Mode
Off: Brake is off
Medium: less forceful and brake time is longer(for glider)
Hard: more forceful and brake time is shorter (for glider)
2. Timing Mode
Automatic: for all motor types
High: hard (recommended for more than 10 poles motors and outrunners motors
For some high KV motors, if it shakes while rotating in high speed, the
High timing mode is recommended.
5. Cut-off Voltage
Cut-off Voltage mode
High
Medium
Low
Li-ion&Li-polymer
3.2V
3.0V
2.8V
Li-Fe
2.8V
2.5V
2.2V
6. Cut-off Mode
Hard: the motor immediately stops as voltage drops to the cut-off voltageBe
suitable for Glide models
Slow down: motor slowly reduces power when voltage drops.