Brushed Esc Manual 2100003 4 ENGLISH
Brushed Esc Manual 2100003 4 ENGLISH
Brushed Esc Manual 2100003 4 ENGLISH
Thanks for purchasing our electronic speed controller (ESC). The power system for RC model can be very dangerous, please
read this manual carefully. In that we have no control over the correct use, installation, application, or maintenance of our
products, no liability shall be assumed nor accepted for any damages, losses or costs resulting from the use of the product.
Features:
Thanks for purchasing our electronic speed controller (ESC). The power system for RC model can be very dangerous, please
read this manual carefully. In that we have no control over the correct use, installation, application, or maintenance of our
products, no liability shall be assumed nor accepted for any damages, losses or costs resulting from the use of the product.
Specification:
Model: WP1040-BRUSHED
WP1040-BRUSHED Crawler & Boat
Cont. / Burst Current: Forward 40A / 180A
Reverse 20A / 90A
Input 2-3S LiPo / 5-9 Cells NiMH
Cars Application 1:10 On-road, Off-road, Buggy, Truggy, Monster Truck
1:10 Crawler, Tank/Boat
Motor Limit 2S LiPo 540 or 550 size motor ≥12T or RPM <30.000@7.2V
5-6Cells NiMH
Motor Limit 3S LiPo 540 or 550 size motor ≥18T or RPM <20.000@7.2V
7-9Cells NiMH
Resistance Fwd: 0.002 Ohm, Bwd: 0.004 Ohm
Built-in BEC 2A/6V (Linear mode BEC)
Dimension & Weight WP1040-BRUSHED 46.5*34*28,5mm 65g
WP1040-BRUSHED Crawler & Boat 46.5*34*28,5mm, 70g
Begin to use:
1. Connect the ESC, motor, receiver, battery and servo according to the following diagram
“+” and “-“ wires of the ESC are connected to the battery pack.
The control cable of the ESC (trio wires with black, red and white color) is connected to the throttle channel of the receiver
(usually CH2). The “Motor +” and “Motor –” wires are connected to the ESC without any order. If the motor runs in the opposite
direction, please swap these two wire connections.
2. Set the transmitter
Please set the D/R, EPA and ATL to 100% for throttle channel (for transmitter without LCD display, please turn the knobs to
the maximum value), and set the TRIM of the throttle channel to 0 (for transmitter without LCD display, please turn the TRIM
knob to neutral position). For some radios the direction of throttle channel shall be set to “REV” while for others shell be set to
“NOR”.
In order to make the ESC match the throttle range of different transmitters, the calibrationof the ESC is necessary. To
calibrate the ESC, please turn on the transmitter, keep throttle stick at its neutral position, wait for 3 seconds to let the ESC
execute self-test and automatic throttle calibration. When the ESC is ready to run, a long beep sound is emitted from the
motor. Note: Please calibrate the throttle range again when using a new transmitter or changing the settings of the neutral
position of throttle channel, D/R, ATV, ATL or EPA parameters,otherwise the ESC may not work properly.
If the voltage of battery pack is lower than the threshold for 2 seconds, the ESC will enter the protection mode. When the car stops,
the red LED blinks to indicate the low voltage cut-off protection has been activated.
2. Over-heat protection:
When the internal temperature of the ESC is higher than 100 Celsius degree or 212 Fahrenheit degree for 5 seconds, the ESC will
reduce and cut off the output power. When the car stops, the red LED blinks to indicate the over-heat protection has been
activated. If the ESC cools down to 80 Celsius degree (176 Fahrenheit degree) the output power is recovered to normal state.
The ESC will cut-off the output power if the throttle signal has been lost for 0.1 second. The “fail safe” function of the radio system
is strongly recommended to be activated.
The difference between “BRUSHED” and “BRUSHED CRAWLER & BOAT” ESC:
“Brushed” ESC uses “Double-Click” method to make the car go backward. When you move the throttle stick from forward zone to
backward zone for the first time, the ESC begins to brake the motor, the motor speeds down but still running, so the backward
action is NOT happened at this moment. When the throttle stick is moved to the backward zone again (The 2nd “click”), if the motor
speed is slowed down to zero (i.e. stopped), the backward action will be activated. The “Double-Click” method prevents mistakenly
reverse when the brake function is frequently used in steering.
“Brushed-Crawler & Boat” ESC uses “Single-click” to make the car go backward. When you move the throttle stick from forward
zone to backward zone, the car will go backward immediately. This mode is common for the Rock Crawler and tank.
The maximum reverse force (for backward running) is 50% for the general “Brushed” ESC, 100% for the “Crawler” mode of a
“Brushed-Crawler & Boat” ESC, and 25% for the "Boat" mode of a “Brushed-Crawler & Boat” ESC.
The Low Voltage Cut-off Protection modes are different (Please check the instructions in the section of “PROTECTION
FUNCTIONS”)
Trouble Shooting:
Declaration of conformity:
For the products manufactured by Absima GmbH mentioned in this manual the compelling and relevant EC Directive will apply:
Directive: 2004/108/EG
This symbol on the products and / or accompanying documents means the used electrical and electronic products must be at the end
of their lifetime separated from household waste. Please take these products for the treatment, recovery and recycling to designated
collection points, which will receive the devices free of charge. The proper disposal of this product, prevent any potential adverse
effects on humans and the environment which could otherwise arise from inappropriate waste handling at the end of its lifetime. For
more details of your nearest designated collection point, contact your local authority. For business users in the European Union, please
contact your dealer or supplier for further information if you wish to dispose electrical and electronic equipment. He holds further
information ready for you. Information on disposal in other countries outside the European Union. This symbol is only valid in the
European Union.
Phone: +49 911 650841 30 Fax: +49 911 650841 40 E-Mail: info@absima.com