MUT-3 User Manual
MUT-3 User Manual
MUT-3 User Manual
Heart-Beat Motors
MITSUBISHI MOTORS
Foreword
This manual explains M.U.T.-III: functions, operating procedures, and other related information. By reading this manual you will obtain a basic understanding of M.U.T.-III and Vehicle Communication Interface (hereafter abbreviated as V.C.I.) functions and methods of operation. Because there are differences in M.U.T.-III methods of operation due to the vehicle electronic control system, be sure to read this manual and Online Help prior to operation. This manual was written based on the October 2006 version of the M.U.T.-III system. Please note that the information herein may not always agree with your version of the M.U.T.-III system due to system specification changes and version upgrades. Please take good care of this manual along with your M.U.T.-III product.
Table of Contents
Chapter 1 Product Overview........................................................................................ 1
1-1. Precautions...............................................................................................................................1 1-2. V.C.I. Outline Drawing and Component Names........................................................................2 1-3. M.U.T.-III Components Explanations ........................................................................................3 1-4. Harness Connection Method ....................................................................................................5 1-5. Combination Chart of Harness and Vehicle ..............................................................................6
Warning
Warning messages alert you to a procedure or practice which, if not followed correctly, could lead to death or serious injury. Caution messages alert you to a procedure or practice which, if not followed correctly, could lead to serious injury and/or property damage.
Caution
Icon Examples
The The
symbol alerts you to a prohibited action. symbol alerts you to an action that must be enforced.
Warning
Do not plug in or unplug the power AC adapter Drivers should not operate the unit while with wet hands. driving. Operating the unit while driving may result in Doing so results in the risk of electric shock. a traffic accident.
When using the cigarette lighter plug to supply power to the V.C.I. unit, be sure the power voltage supplied is DC32V or less. Applying a voltage greater than DC32V results in the risk of fire. M.U.T.-III as provided to dealers includes 12V accessory / cigarette lighter plug adapter to power M.U.T.-III during extended test drives.
Maximum voltage the V.C.I. can withstand is 40V. Do not use the V.C.I. on systems greater than the 32-volt system mentioned previously. Violating this requirement results in the risk of a ground fault, damage and/or electric shock.
Warning
The V.C.I. screen is liquid crystal display or LCD. In the unlikely event that the display breaks due to impact, do not let your skin come in contact with the LCD fluid. If your skin comes in contact with the LCD fluid, wash your skin thoroughly with water. If skin rash or abnormality occurs seek medical attention from a doctor. Do not use the unit if the power AC adapter plug or cord is damaged or plugging into the outlet is loose. Use under such conditions may result in electric shock, an electric short and/or fire.
Be sure to hold the harness connector when Unplug the power AC adapter from the outlet disconnecting from the vehicle. Do not when the unit is not in use. disconnect the harness by pulling on the cord. Failure to do so may result in injury, burns, electric shock caused by insulation Pulling the cord rather than the connector deterioration, or fire due to a short circuit. may result in damage to the lead wire inside the cord, thereby causing a short and possibly starting a fire.
Warning
When the harness is connected to the V.C.I., be sure to check the top and bottom of the connector and connect the harness perpendicularly to the connector of the V.C.I. Connecting at an angle may result in bending of the pins of the connector. Check for the secure connection of the harness before tightening of the screw locks. The bent pin may contact the connector case, thereby causing an electric short which leads to damage to the V.C.I.
Please Note
Do not expose the PC or V.C.I. to direct sunlight or high temperatures, or leave the unit in sun-heated cars. Such action may result in system failure. Store the PC and V.C.I. in a dry environment at room temperatures. Moving the PC and V.C.I. to a location with a very different temperature and humidity than that of the previous location may result in external or internal condensation. Caution is required. Protect the PC and V.C.I. from exposure to elements such as rain, dirt, dust, food and liquids. Be careful when handling the PC and V.C.I. Dropping the units may result in damage. Do not expose either unit to engine oil, gasoline, antifreeze or battery acid. Also, do not clean the PC or V.C.I. case using solutions such as thinner or benzene. Doing so may result in deterioration of the case surface. Prior to connecting the M.U.T.-III main harness between the V.C.I. and vehicle, turn the IG switch to OFF. Connecting the V.C.I. harness with the IG switch ON may damage the V.C.I. programming. Use only the power AC adapter included with the PC (or approved replacement), power cigarette plug, other probes, main harness and other cables. Use of unspecified parts may result in damage or malfunction due to excess voltage or insufficient contact. The LCD display of this unit turns off when the supplied voltage is less the DC 8V. This is not an error. The power supplied should be from 8VDC to 32VDC. Keep all V.C.I. connectors and openings away from dirt and static electricity. Exposure to dirt and static electricity may result in malfunction and damage.
Precautions
Work Precautions
When performing vehicle inspection work at the work site with the engine running, either use an exhaust gas discharger or ventilate the area sufficiently. When working on a vehicle, be sure to apply the parking brake and set wheel chocks in place to prevent the car from moving.
Driving Precautions
If you wish to use M.U.T.-III while driving the target vehicle, first verify that all parts are properly assembled. While driving, always have an assistant operate M.U.T.-III. Be sure that the M.U.T.-III main harness and other cables will not interfere with driving. Install and remove the PC and V.C.I. with the vehicle parked, IG switch OFF.
Trigger harness (MB991826) (Not available in US) CF memory card & adapter (MB991939) (MB991853)
<<Component Names>> 1. I/F cartridge terminal 2. LCD screen 3. Indicator lamp 4. Operation button (Used with V.C.I. functions) 5. Memory card removal lever
2
6. Memory card insertion port 7. Power switch 8. Main harness terminal 9. USB terminal 10. Trigger terminal
(3) M.U.T.-III Main Harness A (MB991910) Used when connecting the V.C.I. with vehicles that have only one 16-pin diagnosis connector. Supports fault diagnosis and ECU updating on the above-described vehicles Supports the CAN communication system
(4) M.U.T.-III Main Harness B (MB991911) Used when connecting V.C.I. with vehicles that have a 16-pin + 12-pin or 16-pin + 13-pin diagnosis connector. For models equipped with only 12-pin (or 12-pin + 12-pin) diagnosis connector, connect the M.U.T.-II adapter harness (MB991498) to the end of this harness in the same as M.U.T.-II, and power is supplied from the cigarette lighter socket.
(5) M.U.T.-III Main Harness C (MB991914) (For US only) Used when connecting the V.C.I. with vehicles that have the 420A engine and F4AC1 transaxle.
(7) Trigger Harness (MB991826) (Not available in US) A harness with a trigger button used to manually insert a trigger point for data acquisition from the drive recorder function during data recording.
(8) Measurement Adapter (MB991825) An adapter used to connect the V.C.I. and measurement probe for voltmeter and ohmmeter readings. Or used when outputting Simulated Vehicle Speed with a vehicle whose diagnosis-connecter cannot receive vehicle speed signal.
(9) Measurement Test Leads (MB991499) Test leads used for voltage and / or resistance measurement. Test leads MB991499 acquire quality replacement test leads from Radio Shack or similar electronics stores.
(10) I/F Cartridge Used to implement special functions that cannot be implemented with the V.C.I. unit alone. The following I/F cartridges used with M.U.T.-II can be used with M.U.T.-III as well: SWS I/F cartridge Daimler-Chrysler Corporate I/F cartridge
<Fig. 1>
<Fig. 2>
Connect the trigger harness to the V.C.I. trigger terminal. (Not available in US)
5
Connect the measurement adapter to the V.C.I. trigger terminal. Insert the measurement leads to the adapter. For best results, match the test lead colors with those on the adapter.
Diagnostic Function
Fault diagnosis ECU update Fault diagnosis 16Pin&12Pin ECU update Fault diagnosis 12Pin ECU update Fault diagnosis 16Pin&13Pin ECU update Vehicle with Fault diagnosis 420A Engine and F4AC1 Transaxle ECU update
O O O O O O O -
Harness Name 01 M.U.T.-III Main Harness A MB991910 02 M.U.T.-III Main Harness B MB991911 03 M.U.T.-III Main Harness C MB991914 (For US only) 04 Conventional Vehicle Inspection Adapter Harness (M.U.T.-II adapter harness) MB991498 05 ECU Update Adapter Harness MB991855
Illustration
Basic Functions
Reads various diagnostic codes and displays the codes by name and number. Reads RAM data inside ECU and displays the data in digital and graphic form. (Available with ECUs that support serial communication only) Permits forced operation or shutdown of various types of actuators that is required for service. (Available with ECUs that support serial communication only) Outputs vehicle speed signal to appropriate ECUs facilitating diagnosis without travel. Permits recording and displaying arbitrary service data that is determined for an arbitrarily specified time. Permits measurement of DC voltage within the range of 0- 40V using the voltage measurement function. Permits measurement of resistance within the range of 0-100K using the resistance measurement function. Permits SWS diagnosis using the SWS monitor kit (MB991806). Identifies CAN bus failures that occur in vehicle that is subject to the diagnosis and narrows down a cause. Permits updating programs in ECU for system version upgrade. Displays with Service manual data. In addition, the system supports interactive fault diagnosis. The Interactive Diagnosis permits user to use both the scan tool viewing functions and service manual troubleshooting procedures. (Not available in US and Australia) Permits measurement of belt tension using Belt tension meter set (MB991668). Permits measurement of fuel pressure using a pressure gauge set (MB991637 / MB991981), and displays it on PC. (Not available in US) Permits more precise measurement of fuel consumption by measuring injection quantity of fuel injector.
Actuator tests
V.C.I. Functions
2-2-2. Fuel Pressure measurement (Not available in US) The system analyzes faults by measuring fuel pressure using the Pressure gauge set (MB991637 or MB991981). Pressure gauge for LP: MB991655 or MB991979 for HP: MB991708 or MB992007
The V.C.I. reads the fuel pressure, which is converted into voltage value by the pressure gauge. Then the system converts it back to pressure value and displays it as text or graph on PC screen. (refer to 10-2-1.)
V.C.I. Functions
2-2-4. V.C.I. Stand-alone Diagnosis You can read out DTCs with V.C.I. stand-alone by using a memory card, which is storing a diagnostic data transferred from PC. There is no need to carry PC or USB cable on the diagnosing vehicle. (For detailed operation, see 4-4)
1. Transfer the diagnostic database file into a memory card. (4-4-1) 2. Insert the memory card into V.C.I., then connect the V.C.I. and the vehicle with an appropriate main harness. 3. Start reading out DTCs from vehicle-installed ECU by V.C.I. stand-alone. (4-4-2) Note: Until a new database file will be distributed, you do not have to operate above step1. Please proceed just step2 and 3.
10
[To start up M.U.T.-III System] 2. Double-click the M.U.T.-III icon displayed on the desktop to start up the system.
[M.U.T.-III icon]
Trademarks Microsoft, Windows 2000 and Internet Explorer are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Adobe, the Adobe logo, Adobe Acrobat and the Adobe Acrobat logo are trademarks of Adobe Systems Incorporated.
11
2.
Press Exit button displayed on the lower right portion of the M.U.T.-III Start screen. M.U.T.-III system will close.
[Shutting down the PC] 3. Click the Windows Start button (lower left portion of the screen), and select Shut Down.
4.
Select Shut down from the pull-down menu, and press the OK button.
12
Screen Explanations
To set option settings, e.g. displaying language. (refer to 3-4.) Shows M.U.T.-III Owners Manual. (refer to 3-5-2.) Starts Service Manual Viewer (SMV). For detailed operation procedure, click the SMV MANUAL bookmark on the left screen of Adobe Reader.
To diagnose vehicles by selecting each system (ECU). e.g. -Reading diagnostic trouble code -Actuator test -Drive recorder For detailed operation procedure, refer to 3-3-1.
-To display saved data (Drive recorder, SWS monitor) -V.C.I. Stand-alone Diagnosis (4-4) -All DTCs Function (4-5) -ECU reprogramming (Chapter 9) -Measurement Function (Chapter 10)
13
Screen Explanations
The Special Function selection screen allows you to switch between major categories by selecting the tabs located on the upper part of the screen.
<Diagnostic Screen>
The diagnostic screen displays three titles in layer format, informing you what is being implemented on each system. The screen does not allow you to switch systems by selecting the upper title areas.
14
(2) STV Top Menu Press System Select button on the STV Top Menu screen.
(3) System Selection Screen Select either one of Up to 2005MY or From 2006MY for the Model Year of the vehicle you are diagnosing. Then follow the each operation below.
*a
$ When selecting Up to 2005 MY 1. Select a system on the System List (*a), and press
2. If the system has a loading option, the Loading Option Setup list (*b) will be displayed. Then, select an item having a box checked ( ) and press button.
*c *a *b
$ When selecting From 2006 MY 1. Confirm the contents of the Vehicle Information list (*c). -When the contents are not describing the vehicle, press to correct the information. (For details, refer to 3-3-2)
Note: M.U.T.-III for EU countries, the options for Model Year is classified in Up to 2004 MY and From 2005 MY.
2. Select a system on the System List (*a), and if the Loading Option Setup list (*b) is displayed, select an item having a box checked ( ). Then press button.
15
(4) Function Selection Screen After System selection, the Function selection menu of the selected system appears. Select a button that you want to perform. In the picture on the left shows the screen appears when the MPI/GDI/DIESEL system, which is a representative example, is selected. Details of each buttons are as follows.
[MPI/GDI/DIESEL s Function Selection menu]
Note: As available functions differ between systems, there might be functions that will not appear when you select other system.
Check Chart For Problem Symptoms -- To view the Symptom Chart of Service Manual. Self-diagnosis -- To read out or erase Diagnosis Trouble Codes from vehicle ECU. Also, you can read out the Freeze Frame data. (refer to 4-1.) Simulated Vehicle Speed Output --To transmit simulated vehicle speed signal into the vehicle. Data List -- To read the RAM data inside the ECU and displays the data in digital and graphic form. (refer to 4-2.) Actuator Test -- To control the ECU output device. (refer to 4-3.) Drive Recorder -- To record, display or analyze the ECU input / output signals which can be viewed using Data List function. (refer to Chapter 6) Special Function -- To execute special functions specific to the selected system. For detailed operation other than Chapter 5, please utilize each Online Help function. OBD-II Test Mode -- To read out Monitoring test results Provisional DTC and ECU information, which are regarding Emission Related System, from ECU. Readiness Test -- To read out the result of Readiness Test from ECU. Voltmeter -- To measure voltage value using M.U.T.-III. (same operation as 10-2-2) Ohmmeter -- To measure resistance value using M.U.T.-III. (same operation as 10-2-2) Fuel Pressure Gauge -- To measure fuel pressure using a pressure gauge, and display the result on PC screen. (Not Available in US) Check Mode To shorten sampling time of communication by changing the communication method between M.U.T.-III and ECU. This function is available in Data List, Drive Recorder and Actuator Test. Emission Test -- To test the Evaporative Emission Control System of the vehicle. Coding -- To write the vehicle equipment specifications into ECU. SWS monitor Pulse Check
(appears only when selecting SWS system)
(refer to Chapter 7)
(appears only when selecting SWS system) -- To confirm existence of the signal pulse to operate remote system on SWS communication line. 16
(2) The items individual selection screen appears. Apply appropriate information, then press button to return to the Vehicle Information Setting screen (1).
17
Option Settings
[ Environment ]
(2) Select a button corresponding to your purpose. [ Environment ] Change Environmental setting -- To set the driver, which the Service manual data should be installed. Show environmental setting -- To view the settings. Unit set -- To select US unit or metric unit, e.g. lbs : kg Printer set -- To set output conditions of the printer. (3-4-2.) Keyboard set -- To select row of keys: Alphabetical-order or QWERTY. Select Language for display -- To select a language displayed in whole M.U.T.-III system and Service manuals. (Service manual will not be displayed unless the selected language has been downloaded.) [ Data Update ] System Information -- To view versions of installed software on the PC.
[ Data Update ]
3-4-2. Set up Output conditions of Printer (1) When pressing the Printer set button on 3-4-1(2), the Printer window illustrated on the left appears. Select an appropriate printer icon and right-click it to open a pull-down menu; select Printing Preferences.
Note -Set up conditions on this window will not be reflected. (2) The Printing Preferences window of the selected printer appears. Please set output conditions e.g. page setup, and press OK button.
18
Useful Functions
(2) The online help function allows you to view a general overview of each screen and refer to explanations of the various button functions. If you wish to move the screen up or down, select the applicable scroll button located on the right side of the screen.
Taskbar
& Selecting M.U.T.-III system or Adobe Reader appearing as buttons on the Taskbar switches between the system and the manual. You can hereby readily check this manual while operating M.U.T.-III system.
19
(2) Press
Self-diagnosis
button.
The system automatically communicates with the vehicle ECU and obtains the diagnostic trouble codes (DTCs).
(3) Diagnostic trouble codes (DTCs) of the selected system, which is currently stored in the vehicle ECU, are listed. DTC Procedures From Service Manual --Switches the mode to interactive fault diagnosis mode. (refer to 4-1-2) (Not Available in US, Australia) Change Sensitivity --Allows you to increase the diagnostic code detection capability of the ECU or return the sensitivity level back to normal. Erase DTCs --Deletes the diagnostic trouble codes. --Displays the Freeze frame data.
20
4-1-2. Interactive Fault Diagnosis Mode (1) Press DTC Procedures From Service Manual button.
Note: It is not necessary to select DTC code to be diagnosed..
(2) Vehicle Information Setting Screen -Currently selected information is displayed in each items field. (Blank space means the information is not selected.) - TYPE , CLASS and MODEL YEAR are compulsory input. --OK --Deletes whole information --Displays history of settings as open options. Note: In case you want to be Interactive diagnosis mode, Workshop Manual data has to be installed into PC.. (3) Diagnosis codes chart Screen Diagnosis codes of the selected vehicle are displayed. In order to diagnose for current DTC, press button to start troubleshooting.
(4) Workshop Manual data of the selected DTC will be displayed. Proceed in accordance with displayed procedure on Workshop Manual, press button or button to go to next step. Press button to scroll the screen up and down, left and right movements. When you finished your operation, press button lower-left of the screen to close Workshop Manual screen. On the Workshop Manual screen, another Workshop Manuals can also be started up by pressing button. As it enables to browse multiple Workshop Manuals, so it is possible what Wiring diagram can be browsed while doing diagnosis each DTC. -- to (5)
21
(5) Workshop Manual select screen Select manual to be browsed. Note: Vehicle Information button is not activated.
(6) Shift of Workshop Manual Select content you want from Workshop Manuals displayed on the task-bar button of the screen. Note: Workshop Manual in different kind of vehicles cannot be browsed simultaneously.
(7) On Workshop Manual Viewer SMV that would be started up for the first time is called SMV(Main), and others are called SMV(Sub). - When SMV(Main) will be closed by button, other SMV(Sub) will be also closed altogether. - Each Workshop Manual(Sub) can be closed individually. - Select content you want from Workshop Manuals displayed on the task-bar bottom of the screen.
22
Data List
(2) Displaying Graphs 1 The graph screen displays the data of 4items/4graphs. -- 4items/4Graphs display -- 4items/View Graph (overwrite) -- View Text -- View1/2 -- Change Time Scale -- Change Data Scale -- Pause -- to 4-2-2(2) -- Start -- View2/2 Note: Record Data ( button allows you to save the portion of Data List displayed on the graph)-- refer to 4-2-2(2)
(3) Displaying Graphs 2 The data of displayed items are overlaid on a graph. Available function buttons are the same as Graph 1.
23
Data List
4-2-2. Details of Data List Screen (1) Displaying Item Selection Item Group Select Select a group of the data to be displayed, and press button.
Item Select By default, none of the items are selected. Select an item that you wish to display, and apply the selection using or buttons. --Inserts all the items from Available item list into the selection areas of Selected item list. --Inserts the item selected in Available item list into the selection area of Selected item list. --Inserts the item selected in Selected item list into the lowermost area of Available item list. --Inserts all the items from Selected item list into the lowermost areas of Available item list. --Changes the order in which the items are displayed in the Selected item list and the Available item list, in the sequence of default setting. When complete the selection, press button.
Note: -When there is no selected item, all items are displayed. -The column of item No appears in green when the service data is OBD basic items. -Fuel pressure and Voltmeter cannot be selected simultaneously. When you select the item Fuel pressure 1. Pressure gauge list will be displayed after item selection. Select a type of pressure gauge used for fuel pressure measurement, and press button.
2. Set up the calibration voltage of the pressure gauge, and press button. Note: For details on how to measure calibration voltage, refer to 10-2-1(1).
24
Data List
(2) Record Data 1. Graph data is paused by pressing button, and the data can be saved on the PC automatically. -- OK -- to 2 --Cancel (Not save the data and return to the pause screen. Pressing button starts data list again.) 2. The data has been saved. The file name of the recorded data is set as SD + YearMonthDay + Time (military time including seconds), using the PC time as standard. -- OK Note: For details on how to view the saved data, refer to 6-2-2(3). (3) Changing Item Display Order -On the data list display screen, you can change the display order of the items. The change is possible for both text display and graph display. -The display order change can be performed with the data list displayed continuously. (The graph display is reset.) -Selecting the name display area of an item fixes the item. Then over-scrolling only the items not selected using the vertical scroll keys changes the order. -The selection can be released by selecting the item again. -The function is not activated while a data range display area is selected. (Selection, release, and scroll functions of item are not available.) (4) Data Range Change -Select a data range display area on the graph. -When the color of the selected area turns into yellow, you can enter values. -Entering method: Use PC keyboard or scroll keys. -When use PC keyboard, enter a value, and then press the [Enter] key or release the selection of the data range display area to determine the data range change. -When the scroll keys, and , on the screen are used for the data range change, pressing the key each time changes the data range setting by +5 % of full scale and the . key changes it by 5 %. The change is determined at each key pressing.
25
Actuator Test
4-3-1. Actuator Test (Type A) If the screen illustrated on the left appears.
(1) Select a test item and press button to activate actuator. --Displays Actuator test Reference Table of Service Manual. (Not Available in US, Australia) --Data List simultaneous display (Text) --Data List simultaneous display (Graphs)
(2) Actuator Test Executing If you want to interrupt Actuator Test, press When completes the test, a dialog box appears. Press button. " returns to screen (1).
button.
& Data List simultaneous display (Text) Refer to (1)(2). --Select items for Data list display (For details how to select items, refer to 4-2-2 (1).)
& Data List simultaneous display (Graphs) Refer to (1)(2). --Select items for Data list display (For details how to select items, refer to 4-2-2 (1).) --Change Time Scale --Change Data Scale
26
Actuator Test
4-3-2. Actuator Test (Type B) If the screen illustrated on (2) or (3) appears.
(1) Press button located next to item name, and select a test item from the pull-down menu. -When the selected item has no parameters -- to (2) -When the selected item has parameters -- to (3) --Displays Actuator Test Reference Table of Service manual. --Data List simultaneous display (Text) --Data List simultaneous display (Graphs)
(2) Press
(3) The test item that you have selected need to be set some parameters. After completes the parameter setting, press button to execute the Actuator Test. -- to (4)
* *
* --Select the Value-- : Select the value from the pull-down. * --Input the Value-- : Input the value using hexadecimal keys appeared by clicking the input box.
27
Actuator Test
(5) Actuator Test Executing If you want to interrupt the Actuator Test, press When completes the test, a dialog box appears. Press button. " returns to screen (2) or (3).
button.
& Data List simultaneous display (Text) Refer to (1)-(5). --Select items for Data list display
& Data List simultaneous display (Graphs) Refer to (1)-(5). --Select items for Data list display --Change Time Scale --Change Data Scale
28
(1)
(3) Select System Function tab, then press V.C.I. Stand-alone Diagnosis
button.
(4) The version of current data for V.C.I. Stand-alone Diagnosis is indicated on the left table. Please select a destination having a box checked ( ) on the right table, then press button to transfer the data.
29
(5) Drive Selection Select the appropriate drive (removable disk drive) to save the data, then press button.
(7) Before you remove the memory card, double-click the icon for removal of adaptor displayed on the bottom-right corner. Double click here (8) Select [PCMCIA IDE/ATAPI Controller] or the other appropriate device, then press Stop button.
(10) After displayed the message The device can now be safely removed from the system, push the lever on the side of PC m-card slot and remove the memory card. Caution: Do not remove the memory card away unless complete above method or turn off the PC.
30
<Vehicle Select> Up to 2005MY From 2006MY For EU countries, the options are classified in Up to 2004 MY and From 2005 MY.
(3) Press button to browse the list until the LCD displays the appropriate category for the vehicle you are diagnosing, then press (Enter) button. -When selecting Up to 2005 MY -- go to (5) -When selecting From 2006 MY -- go to (4) Note:
- The display scrolls in the direction of the arrow displayed on the first line. To switch the direction, press (Esc) button once. - If you press (Esc) button twice in quick succession, the screen goes back to the Main Menu.
Display Example
<Vehicle Select> OUTLANDER(CW0#) Press Enter button <Model Select> Z26A Press Enter button <Series Select> XNLHL6 Press Enter button <MY Select> 2006 Press Enter button
(4) As next Vehicle Select menu is displayed, press button to browse the list until the LCD displays the vehicle name, then press (Enter) button. After vehicle selection, the LCD menu is followed by Model Select, Series Select, and Model Year Select. Perform each selection in the same operation. " go to (6) Note: -The options are displayed in alphabetical order.
31
Display Example
(5) System Selection Press button to browse the list until the LCD displays the system you want to diagnose, then press (Enter) button.
Display Example:
(6) Option Selection If the system has a loading option, the Option Select menu will be displayed. (If not, go to (7) directly) Select an option, then press (Enter) button.
Display Example:
<DTCs> 01/10 C1234 RL Weel Sp C xxxx * Pump Motor C xxxx Brake Peda U xxxx * Bus off
(7) Display of the DTCs The DTCs that have been read from ECU are displayed. -The number shown on the right edge of first line is indicating [Serial # / Total number of detected DTCs]. -Press button to display the next DTC. (When having only one DTC, the arrow is not displayed on the first line.) -V.C.I. is constantly reading DTCs and updating the display. -If the system supports status recognition, current status of each DTC is expressed by the following symbols, which appears between code and name. Active : [ ] (blank) Stored : [ * ] Pending : [ # ]
-Pressing (Enter) button shows full name of the DTC. (To return to the previous screen, press or once.)
NOTE: The following systems, which need special process to read DTCs, are out of target for the V.C.I. Stand-alone diagnosis. -Some of ABS for MIRAGE / LANCER(CMO/CLO#) -SWS for GRANDIS(NA4W) / COLT(Z20#)
32
Message
Cause/Remedy
<Cause> Failed to access the memory card. <Remedy> 1. Verify that the memory card is inserted into PC correctly. 2. Press the V.C.I. Enter key to go back to the Main menu, then start the operations over again. <Cause> The V.C.I. stand-alone diag. database stored in memory card does not work with the V.C.I. built-in program for V.C.I. stand-alone diag. <Remedy> 1. Press the V.C.I. Enter key to go back to the Main menu. 2. Remove the memory card, then insert it into PC to update the database.(refer to 4-4-1) 3. If the database is the latest one, connect PC and V.C.I. to update the V.C.I. built-in program. 4. Start the operations over again. <Cause> Failed to initialize ECU by any cause. <Remedy> 1. Confirm that the system option that you selected is installed in the vehicle. 2. Check if the communication wire between V.C.I and ECU is breaking or not. 3. Verify that proper main harness is connected. 4. Press the V.C.I. Enter key, then restart the procedures from system selection operation. (4-4-2(5)) * Check the battery voltage of the diagnosing vehicle. <Cause> Failed to read out DTCs. <Remedy> 1. Confirm that the system option that you selected is correct. 2. Press the V.C.I. Enter key, then restart the procedures from system selection. (4-4-2(5)) <Cause> The information read from ECU is not registered in the database. <Remedy> 1. Remove the memory card, then insert it in PC to update the database. (refer to 4-4-1) 2. Start the operations over again. <Cause> Communication between V.C.I. and ECU got disconnected from any cause. <Remedy> 1. Verify that the IG switch is turned ON. 2. Check if the communication wire between V.C.I. and ECU is disconnected or not. 3. Pressing the V.C.I. Enter key proceeds on the diagnosis. * Check the battery voltage of the diagnosing vehicle. 33
All DTCs
All DTCs
(3) Select a button corresponding to your purpose. Read all DTCs --Displays a list of all DTCs read from vehicle ECU. Erase and Read DTCs --Erases DTCs from system to system, and displays a list of all DTCs read from vehicle ECU. Note: -DTCs that failed to be erased are displayed on the list. -DTCs that take time to detect after being erased will not be displayed. (4) System Selection Select either one of Up to 2005MY or From 2006MY for the Model Year of the vehicle you are diagnosing. Then follow the each operation below.
*a
Note: M.U.T.-III for EU countries, the options for Model Year is classified in Up to 2004 MY and From 2005 MY.
$ When selecting Up to 2005 MY The System List (*a) appears on the screen. -All the systems are selected by default. -Select systems to read DTCs having the box checked button. ( ), then press (Clicking the box deletes the mark)
34
All DTCs
*c *a *b
$ When selecting From 2006 MY The System List (*a) and the Vehicle Information list appear on the screen.
(*c)
1. Confirm the contents of the Vehicle Information list (*c). -When the contents are not describing the vehicle, press button to correct the information. (refer to 3-3-2) 2. Select systems to read DTCs having the box checked ( ), and its option if necessary, then press button. System List (*a) -All the systems are selected by default. -Clicking a box deletes the mark. -System, which has loading options to be chosen, is indicated by underlining the name. system name (Select Option!): Not chosen system name (option name) : Has been chosen -Systems to read DTCs must have completed the loading-option selection. Loading Option Setup list (*b) -Only displayed when the column of the system, which has loading-options to be chosen, is being selected (appearing in yellow color) on the System List (*a). -When this list appears, select an appropriate option having the box checked ( ). Note: button -- Sets all systems selected on System list. button -- Sets all systems unselected on System list. -Deleting marks on systems, which are not installed in the vehicle, will shorten the processing time. -It is no problem if a system, which is not installed in the vehicle, is selected.
35
All DTCs
*a
*d
(8) Results System List (*a) -Indicates presence or absence of DTCs on the results field as below. OK : DTCs are not detected TC : DTCs are detected - : Unchecked (out of the check system) NC : Not equipped or communication error Diagnostic trouble code(s) (*d) -All detected DTCs are listed. -Indicates status of the DTCs as below. Active : The trouble occurs currently Stored : The trouble had occurred in past - : Not supporting status recognition -When selecting a system with TC result on the System List (*a), columns of corresponding DTC on the Diagnostic trouble code(s) (*d) will appear in blue color. Pressing button returns the screen to (3).
NOTE: The following systems, which need special process to read DTCs, are out of target for the All DTCs diagnosis. -Air Conditioner for GRANDIS(NA4W) -SWS for DIAMANTE(F30/40#)
36
button.
37
(3) Special Function menu Select Press Steering Angle Sensor Calibration button.
(4) Steering Angle Sensor Calibration Select a command item and press the button to execute. Note: When the display is Yet as the result of status, it is to (5). When the display is Done as the result of status, it is to (7).
(5) Study Confirmation --Start -- to (6). --Cancel -- to (4). Note: Please execute after making a tire and a steering wheel straight.
38
(7) Re-calibration If the SAS needs re-calibration, press the execute SAS initialization. --Cancel -- to (4).
button to
button to execute.
(9) Clear DTCs Confirmation --Start -- to (10). --Cancel -- to (8). Note: This operation will clear DTCs and all internal error.
39
40
(3) Drive Recorder Function select Press Record button on the Drive Recorder function menu. Note: Data display -- To transfer the recorded data on the V.C.I. into the PC (refer to 6-2), or display the data (refer to 6-3). Record (Read Setting Conditions) -- Restore past recording conditions so that you can execute recording under the same conditions as those used with previously recorded data files. (refer to 6-1-3) Data Storing -- The data saved in a removable disk can be stored into the PC. (refer to 6-2-2(7))
41
(4) Item Select Select an item you wish to record and apply the selection-using button. --Inserts the item selected in Available items list into the selected area of Selected items list. --Inserts the item selected in Selected items list into the lowermost area of Available items list. --Inserts all the items from Selected items list into the lowermost areas of Available item list. --Changes the order in which the items are displayed in Selected items list and Available items list, in the sequence of default setting. When complete the selection, press button. Note: -A maximum of 16 items can be recorded. -Fuel pressure and Voltmeter cannot be selected simultaneously. When you select the item Fuel pressure 1. Pressure gauge list is displayed after the item selection. Select a type of pressure gauge used for fuel pressure measurement, and press button.
2. Set up the calibration voltage of the pressure gauge, and press button. Note: For details on how to measure calibration voltage, refer to 10-2-1(1).
(5) Trigger method / Recording style Select Select trigger method and put Put the mark(s). (Multiple selection) button. mark on V.C.I. Drive recorder.
Manual Trigger --Allows you to set the trigger manually. -- to (8) Diagnosis Code Trigger --Applies the trigger when the specified diagnostic code is generated. -- to (6) Threshold Trigger--Applies the trigger when the condition meets the set threshold. -- to (7)
42
(6) When Diagnosis Code Trigger is selected in (5), the left screen appears. Select an item to be the trigger, and press button. -- to (8). (If Threshold Trigger is selected as well, go to (7))
(7) When Threshold Trigger is selected in (5), the left screen appears. Select an item and edit conditions in Condition Editing table appearing at the bottom of the screen, first.
Condition Editing table UP/DOWN: Threshold or higher / Threshold or lower Level/Edge: Matching data / Data as of the time when it turns to be matching from not matching AND/OR:-Data matching with both of this condition and the other one upper row on Condition of Trigger table / -Data matching with either of this condition or the other one upper row on Condition of Trigger table
Then, press button to set the condition into selected area of Condition of Trigger table. (Condition of Trigger table can include up to 8 conditions.) When completed the setting, press button.
(8) Select the V.C.I. recording area on the left list. Set the sampling interval and rate distributions (before and after trigger) by moving the cursor or by pressing button. --OK -- to (10) --Display of V.C.I. data -- to (9) Note: -You can select from eight recording areas. -It is possible to set consecutive areas as well. -The sampling interval time indicates the data-recording interval for one item. A setting of 0 seconds results in the fastest sampling interval. -When a sampling interval other than the fastest interval is selected, the amount of time in which recording is possible appears. This time is a calculated estimated time and may differ from the actual amount.
43
(9) View V.C.I. Regeneration Data 1. For the data recorded in the selected V.C.I. recording area, the settings of the items are displayed. -- Deletes data recorded in the V.C.I. Select a data you wish to delete, and press this button -- to 2 -- Cancel -- to (8)
(10) Enter the record information (memo) Enter the reference information, such as the vehicle model and diagnosed system name. --OK -- to (11) Note: -As the unit is linked with the PC keyboard, you can enter the information either using the PC keyboard or by using the screen keyboard.
(11) The contents check of setting (1/3) The list of recording settings appears. -- to check set items -- to check threshold trigger conditions (if selected) Press button transmits the settings to the V.C.I.-- to (14)
(12) The contents check of setting (2/3) The list of recording items appears. -- to check threshold trigger conditions (if selected) -- to check recording setting Press button transmits the settings to the V.C.I.-- to (14)
44
(13) The contents check of setting (3/3) (Only if selected in (7)) The list of Threshold conditions appears. -- to check recording setting -- to check set items Press button transmits the settings to the V.C.I.-- to (14)
(14) Transmit Confirmation By pressing button on screen (11)/(12)/(13), the record settings are transmitted to V.C.I.. Press button.
(15) Once the settings have been transmitted from the PC to the V.C.I., a message appears indicating that the settings have been transmitted. Please wait a second.
(16) Press button. Note: -If you wish to start recording immediately, disconnect the USB cable while leaving the V.C.I. switch ON. (Disconnecting the USB cable starts to record the data on V.C.I.) -- to (17) -If you wish to just set the settings and later start recording, turn the V.C.I. switch OFF and then disconnect the USB cable. (17) Recording When you record with a manual trigger, connect the trigger harness to the V.C.I. trigger terminal as necessary. Note: -When the USB cable is connected, the V.C.I. communicates with the PC, thereby prohibiting drive recorder startup. Do not connect the USB cable.
45
(18) Starting Recording To start recording, turn off the engine first, and then turn the ignition switch ON or start the engine and turn the V.C.I. power switch ON. Recording begins after communication initialization. Note: -The number in parenthesis on the V.C.I. LCD screen indicates the recording area of the V.C.I. drive recorder.
(19) Trigger -With a manual trigger, pressing the V.C.I. Enter key activates the trigger, displaying T on the screen. Once the trigger has been activated, the data after the time of the trigger are recorded. Note: -With a diagnostic trigger, the trigger is automatically activated when the specified diagnostic code is generated. -With a threshold trigger, the trigger is automatically activated when the specified conditions are met.
(20) Ending Recording If you wish to end recording, regardless of whether or not the trigger has already been generated, press the V.C.I. ESC key. Once the button has been pressed you can disconnect the vehicle harness and trigger harness.
(21) When you check the data recorded in V.C.I., continue to 6-2-1.
46
Note: Data display -- Displays the recorded data. (refer to 6-3) or edit the data (refer to 6-2-2) Record (Read Setting Conditions) -- Allows you to restore past recording conditions so that you can execute recording under the same conditions as those used with previously recorded data files. (refer to 6-1-3) Data Storing -- The data saved in a removable disk can be stored into the PC. (refer to 6-2-2 (7))
47
(4) Item Select Select an item you wish to record and apply the selection-using button. --Inserts the item selected in Available items list into the selected area of Selected items list. --Inserts the item selected in Selected items list into the lowermost area of Available items list. --Inserts all the items from Selected items list into the lowermost areas of Available items list. --Changes the order in which the items are displayed in Selected items list and Available items list, in the sequence of default setting. When complete the selection, press button. Note: -A maximum of 16 items can be recorded. -Fuel pressure and Voltmeter cannot be selected simultaneously. When you select the item Fuel pressure 1. Pressure gauge list is displayed after the item selection. Select a type of pressure gauge used for fuel pressure measurement, and press button.
2. Set up calibration voltage of the pressure gauge, and press button. Note: For details on how to measure calibration voltage, refer to 10-2-1(1).
(5) Trigger method / Recording style Select Select trigger method, and put Put mark(s). (Multiple selection) button. mark on PC Drive recorder.
Manual Trigger -- Allows you to set the trigger manually. -- to (8) Diagnosis Code Trigger -- Applies the trigger when the specified diagnostic code is generated. -- to (6) Threshold Trigger -- Applies the trigger when condition meets the set threshold. -- to (7) 48
(6) When Diagnosis Code Trigger is selected in (5), the left screen appears. Select an item to be the trigger, and press button. -- to (8). (If Threshold Trigger is selected as well, go to (7))
(7) When Threshold Trigger is selected in (5), the left screen appears. Select an item and edit conditions in Condition Editing table appearing at the bottom of the screen. (refer to 6-1-1(7)) Then, press button to set the condition into selected are of Condition of Trigger table. (Condition of Trigger table can include up to 8 conditions) When completed the setting, press button.
(8) PC Drive recorder setup Please confirm the contents of record setting, and set up the sampling interval with the cursor or button. Select a display format for recording (either Graph or Text) having a circle marked . --Displaying item Select (Graph only)-- to (9) --OK -- to (10) Note: -The sampling interval time indicates the data-recording interval for one item. A setting of 0 sec (fastest) results in the fastest sampling interval. -Recordable time computes the number of the maximum record points as 20000 points, and is displayed. This is the prediction time on calculation and differs from actually recordable time. -The configuration of the displayed file names is DR+ Year Month Day + Time (military time including seconds), using the PC time. <DR: The file saved by the drive recorder is meant> -The setting value of a sampling interval can be chosen from 0sec(fastest)/1sec/10sec/1min.
49
(9) Graph display item selection Select the items you wish to display on the graph. -Selected 4items are displayed during the recording. -The items not selected are not displayed on graph but the data are recorded. -- OK -- to (8)
(10) Enter the record information (memorandum). Enter the reference information, such as the vehicle model and diagnosed system name. --OK -- to (11) Note: Because the unit is linked with the PC keyboard, you can enter the information either directly using the PC keyboard or by using the screen keyboard. (11) The contents check of setting (1/3) The list of recording settings appears. -- to check set items -- to check threshold trigger conditions (if selected) Pressing starts recording go to (14)
(12) The contents check of setting (2/3) The list of set recording items appears. -- to check threshold trigger conditions (if selected) -- to check recording setting Pressing starts recording go to (14) Note: When Graph is selected in (8), the background color of the name column of the item, which is to be displayed in graph during the recording, changes into yellow. (13) The contents check of setting (3/3) (Only if selected in (7)) The list of threshold trigger conditions appears. -- to check recording setting -- to check set items Pressing starts recording -- go to (14)
50
(14) Recording Data [Graph] It saves at the file, expressing data as the set-up record conditions. The four items chosen on (9) are indicated by graph as the left screen (a). [Text] When Text was chosen on (8), and a drive recorder is set up, it saves at a file, acquiring and expressing data as the set-up record conditions. (see the left screen (b))
--Data record end -- to (15) When Trigger is not generated during data record, let the point at the time of a record start is time 0:00.0. --Manual Trigger occurs However, when Diagnosis Code Trigger or Threshold Trigger are chosen as trigger conditions, suppose that it is invalid. (b). Recording screen [Text] Note: -Record is continued until record end button is pushed, even if trigger occurs. -The availability of the hard disk of the PC is checked after record screen display and before record start. When the availability is 100MB or less, a message is displayed and record is stopped. -When the number of record data reaches to 20000 points, a message is displayed and record is completed.
(15) Save record data On the screens of (14), pressing button ends the data acquisition and saves it, and then displays a dialog indicating completion of the record data saving. -- OK -- to Drive Recorder function select menu screen (refer to (3)). Note: *In the case that there is no record data, a dialog is displayed confirming whether to stop the recording. -- OK -- to the drive recorder function select menu -- Cancel -- to (14) to start recording again.
51
(2) Select the data you wish to restore, and press The data was recorded using V.C.I.: to 6-1-1(8) The data was recorded using PC : to 6-1-2(8)
button.
52
(2) Select the System Functions tab on the upper part of the screen, and then press Drive Recorder (Display only) button.
button.
53
(5) Display of V.C.I. Data The status of V.C.I. recording area is displayed. Select a data to be transferred into PC, and press button. -- to (6) When you wish to delete a data, select it and press button.
(7) The data is being transferred from V.C.I. to PC. Please wait for a while.
(8) After completion of data transfer, a dialog box appears asking whether to delete the data on V.C.I.. : Deletes the data, then returns to screen (5). : Returns to screen (5) without deleting the data.
54
(3) Recorded data file list -The file list of the drive recorder (and data list records) saved into the PC is displayed. -You can view the data details by selecting the data you wish to view from the list and pressing button. In addition, you can view graph data by pressing button. (to 6-3-1(3)) -The background color of the line containing the selected file changes into yellow. -- Edit record information -- refer to (4) -- Delete the data file -- refer to (5) -- Save the data file -- refer to (6) Note: -The configuration of the displayed file names is DR+Year Month Day+Time(military time including seconds), using the PC time. -The most recent recorded data appears on top of the list. -Those file names, which begin with SD, contain the data of Data List records. (refer to 4-2-2.(2)) Caution: About CSV file If you open the CSV file on M.U.T.-III using EXCEL, never overwrite and save it. (However, they are allowed after the file is transferred from M.U.T.-III to another PC or copied in another folder.)
55
(4) Edit Data Information 1. Select a file to edit and press [K] button to display the screen illustrated on the left, where you can edit the record information that was entered in 6-1-1(10) or 6-1-2(10). Press button.
(5) Delete Data 1. To delete a data file loaded on the PC, click the check box next to file No. in the file list (refer to (3)) to place a check mark, and press button. (Two or more check marks can be placed.) Note: mark will be displayed, if cursor is moved on a check box and it clicks. (Selection) mark is eliminated by clicking again. (Selection release) 2. File Delete Confirmation A message appears asking if you wish to delete the data file. Press button to delete the file.
(6) Save Data 1. The data file can be saved to a removable disk (floppy disk or memory card). -Insert a disk into the PC, first. -Click the check box next to the file No. in the file list to place a check mark, and press button. (Two or more file selections are possible.) Note: mark will be displayed, if cursor is moved on a check box and it clicks. (Selection) mark is eliminated by clicking again. (Selection release)
56
2. Drive Select Select a drive for saving the data files, and press button.
button.
(7) Data Storing 1. The data saved in a removable disk before can be stored into the PC. -Insert the disk into the PC, first. -Press Data Storing button on the Drive Recorder function menu. (refer to (2))
3. Data Storage Complete The data has been loaded to PC. Press button.
57
(2) Recorded data file list Data file list that contains record of Drive recorder and Data list saved in PC will be displayed. You can view the data details by selecting the data you want to display from the list and pressing button. In addition, you can view graph data by pressing or button. -The background color of the line containing the selected file changes into yellow.
(3) Displaying Text Data --Graph data 1 --Graph data 2 --Select item (to (4)) --Edits extraction conditions (to 6-3-2.(1)) --Sets search conditions (to 6-3-2.(2)) --Jumps to a trigger point. --Saves data (to (6-3-2.(3)) --Displays a correlation diagram (to 6-3-3.(1)) --Displays a distribution chart (to 6-3-3.(2)) --View 1/3 --View 2/3 --View 3/3
58
Displaying Graph 1 --Text data --Graph data 2 --Select item (to (4)) --Edits extraction conditions (to 6-3-2.(1)) --Jumps to a trigger point --Saves data (to 6-3-2.(3)) --Displays a correlation diagram (to 6-3-3.(1)) --Displays a distribution chart (to 6-3-3.(2)) --Change Time Scale --Change Data Scale --View 1/3 --View 2/3 --View 3/3
Displaying Graph 2 Displayed items are overlaid on a graph. -The function buttons are the same as Graph1.
(4) Select item button allows you to select items to be displayed from recorded data. When complete the selection, press button. The item number of service data OBD basic items appears green. --Inserts all the items from Available items list into the selected areas of Selected items list. --Inserts the item selected in Available items list into the selected area of Selected items list. --Inserts the item selected in Selected items list into the lowermost area of Available items list. --Inserts all the items from Selected items list into the lowermost areas of Available items list. --Changes the order in which the items are displayed in Selected items list and Available items list, in the sequence of default setting.
59
Setting table. (Extraction Setting table can include up to 8 conditions.) Press button to display extracted data only in text/graph. --Set Time extraction condition. --Delete selected extraction condition data. Time extraction condition setting After pressing button, time extraction condition setting screen shown on the left will be displayed. Set time range on this screen and press button to display extracted data only. --Return to data extraction condition setting screen.
60
(2) Conditions setting for data search Condition setting screen shown on the left will be displayed after pressing button on text data display screen. Select an item and edit its condition in Condition editing table appearing at the bottom of the screen. (See (1) for more details.) Then, press button to set the condition onto Retrieval condition table. (Retrieval condition table can include up to 8 conditions.) Press button to display text data screen showing * (asterisk) in the Judge column of the data matching with the retrieval condition. --Set Time retrieval condition. --Delete selected condition. Time retrieval condition setting After pressing button, Time retrieval condition setting screen shown on the left will be displayed. Set time range on this screen and press button to display text data screen showing * (asterisk) in the Judge column of the record data matching with the retrieval condition. --Return to Search conditions setting screen.
(3) Data save When pressing button on the screen of displaying data, you can save the extracted or retrieved data into the PC. As the left dialog box appears, press button. Note: The configuration of the file name is original data file name + alphabet (a,b..z).
61
<Correlation Diagram>
(2) Setting the Distribution Chart Pressing button on the screen illustrated in 6-3-1(3) displays the distribution chart settings screen as illustrated on the left. Setting the target data time range, item names, data range, division width, and frequency range and pressing button displays the distribution chart.
<Distribution Chart>
62
63
button.
Note: If the SWS monitor cartridge is not connected to the vehicle, SWS MONITOR button does not appear.
64
(4) This screen appears depending on vehicle SWS version. Select a specification of communication between doors of the vehicle that you monitor, and press button. [New communication between doors] Power windows are controlled by multiplex communication between drivers seat Power window module and other Power window switches. [Old Between-doors communication] Power windows are controlled by multiplex communication between drivers seat Power window module and other Power window motors.
(5) Function Select The SWS monitor menu screen appears. ECU Comm Check -- to 7-1-2. Data List -- to 7-1-3. Function Diag. -- to 7-1-4. Drive Recorder -- to 7-1-5. Keyless Entry -- to 7-1-6. Custom Function -- to 7-1-7. Note: The Keyless Entry and Custom Function buttons will appear depending on the SWS version of vehicle.
button.
(2) Displaying Graph OK appears if the ECU is communicating properly, and NG appears if there is a communication error. NG also appears if the system has not been installed or is installed but not communicating. Prior to performing the check, therefore, it is necessary to identify the system for the monitored vehicle. --Change Time Scale --View text style-- to (3)
65
(3) Displaying Text style If you press How to Check ECUs button, you can view the Service Manual. (Not Available in US, Australia)
(3) Displaying Graph --View text -- to (4) --Change Time Scale --Change Data Scale
(4) Displaying Texts Data List Reference Table --Displays the Data List of the Service manual. (Not Available in US, Australia) Simulated Vehicle Speed Output --Allows you to simultaneously view the Simulated Vehicle speed and Data List. -- to (5) --View graph
66
(5) Simulated Vehicle Speed Output The Simulated Vehicle speed output function displays the simulated vehicle speed and Data List simultaneously. Speed output can be changed in 1 mph or 10 mph increments using the speed adjusting buttons. --Unit: 1mph --Unit: 10mph --View graph
button.
(3) Displaying Graph --View Text -- to (4) --Change Time Scale --Change Data Scale Note: If required operating conditions are not met, the item number appears in pink color.
(4) Displaying Text Data List Reference Table : (Not Available in US, Australia) Displays the Data list of the Service manual. --View Graph Note: If required operating conditions are not met, the item number appears in pink color.
67
(2) The left figure is displayed when the last record remains. Erase recorded data in SWS monitor cartridge, before record data. Press button.
(3) Recording Data Select an item you wish to record. ECU Comm Check -- to (4) Data List -- to (4) after ECU selection Function Diag. -- to (4) after function selection.
(4) Selecting the Trigger Method Manual trigger -Allows you to apply the trigger manually. Item trigger -Allows you to select one or two items and uses the ON or OFF signal of the item(s) as a trigger to start recording.
68
(5) Setting the Recording Time The recording time can be set from 0day 0h 0min to 5days 0h 0min. If you do not wish to set a recording time, press button without setting the time. The day and time are set using . -Day --Unit: 1 day -Hour-Unit: 1h, -Minute-Unit: 1min,
You can also set the time using the slide bars.
(6) Checking the Recording Settings Check the recording settings and press button to transmit the data to the SWS monitor cartridge. A message appears indicating that the recording settings will be transmitted to the I/F cartridge. Press button.
(7) Recording Using the Drive Recorder Once the data have been transmitted to the SWS monitor cartridge, the screen shown at left appears. If the trigger set was a manual trigger, press button to start recording. If the trigger set was an item trigger, recording begins when the set conditions are met. Note: To disconnect the SWS monitor cartridge, press button. The following message appears: Do you wish to disconnect the I/F cartridge? (If so, select YES, then wait for the ready message to appear.) Once the ready message appears, disconnect the cartridge. (8) Ending Recording To end recording, press
button.
69
(9) Data Display Select Data Display button on the screen of (1). You can also display recorded data by returning to the STV Top Menu, selecting Special Functions , then selecting the system function SWS Drive Recorder . In this case, you can view the data without connecting V.C.I. to the vehicle by using an AC-DC adapter (MB991878).
(10) You can set a time in which you wish to regenerate and view the data as described below. The day and hour can be set using buttons. After the setting, press button.
(11) Displaying Recorded Data Select the items you wish to display and press Note: All items are selected as default.
button.
(12) Displaying Data The recorded data are displayed in graph format by default. -- View Text --Displays the previous or next data change point. --Displays the previous or next record. You can also set the settings by operating the slide bar.
70
(2) Deleting Keyless ID When pressing Keyless ID Regist button in (1), the screen illustrated on the left appears. In this screen, all of registered Key ID at present can be deleted. -- Delete all Key ID -- Cancel
(3) Pressing Hazard warning lamp switch of the vehicle deletes the ID completely.
(4) Keyless ID Registration Press Lock-switch or Unlock-switch of the key to be registered three times continuously.
(5) Checking for signal detection Press Recept Inspect button on (1), and the illustrated on the left appears. Press Lock-switch or Unlock-switch of the key checked. When ECU acknowledges the Lock or signal, it displays the signal name and state of the the vehicle.
71
button.
(3) Adjustment Value Initialization When pressing button in (1), you can initialize adjustment value of all functions. As a confirmation dialog box appears, press button.
72
(4) Results The results of the diagnosis are reflected on the configuration screen (Error locations are indicated in red), and the comment is shown on the center lower massage box. --Displays the data of the Service manual pertaining to the error locations. (Not Available in US, Australia)
73
Device
(a)
V.C.I. alone
(b) Load RPG file Select from Data library (c) ECU reprogram
PC + VCI (Optional)
(d) (e) (f) Automatic Database File Reprogram reprogramming Display Data Selection (K-line) Automatic Select from data library in PC (g) Search
Procedure name
Select from Select by key data library in of vehicle any drive info.
1 2 3
CD-Rom => PC PC => CF memory card CF memory card => VCI PC => VCI (Not via memory card)
4 5
9-4-3(c)+ 9-4-4
Note
In case In case In case Special use In case memory card is memory card is memory card only memory card is N/A and (d) is N/A and (d) N/A and (d) (When data N/A failure failure failure stored in VCI)
& Reprogramming by CAN communication system -This is the only way for reprogramming by CAN communication system. -This procedure allows you to select an arbitrary system (ECU) to reprogram as required. -File extension code is .cff.
Device Process name Data selection 1
CD-Rom => PC
PC+V.C.I.
Automatic Reprogramming (CAN) Automatic
9-3-1 9-6
74
Equipments
9-2. Equipments
Necessary parts for ECU reprogramming are as follows Parts Name Parts Number M.U.T.-III Personal Computer Update CD-ROM of reprogramming data CF Memory card128MB MB991853 CF Memory Card Adaptor MB991939 V.C.I. MB991824 M.U.T.-III Main Harness A44-16 1 MB991910 M.U.T.-III Main Harness B44-16/12 MB991911 Reprogramming adapter Harness 12-132 MB991855 Remarks 1 Vehicle which is only equipped with a 16 pin diagnosis connector. 2 Vehicle which is equipped with 16 pin and 13 pin diagnosis connector.
V.C.I. MB991824 Power supply Switch For 16pin diagnosis connector Main Harness A MB991910 For 12pin diagnosis connector For 16pin diagnosis connector
Adaptor Harness
For 13Pin Diagnosis connector
75
(3) Select System Function tab, and press ECU reprogramming button.
(4) The message Please update to a new database file. is displayed when the new Update CD-ROM is recognized. Press button.
(5) The message Please wait! is displayed during progress. When complete the updating, the message disappears. You can remove the CD-ROM from PC.
76
< CASE 2 > (1) By inserting ECU Reprogramming data CD-ROM in the CD-ROM drive of a PC, update of ECU Reprogramming data starts automatically. And by operating it according to the message displayed, it is possible to update the ECU Reprogramming data in M.U.T.-III in the newest state.
(2) After terminating M.U.T.-III, insert Reprogramming data CD-ROM in the CD-ROM drive of a PC.
(3) Confirmation of update Click the Yes button, update of the ECU Reprogramming data in M.U.T.-III is started. Remark: An end message changes by the kind of data updated at this time. (4) Update finished (Case A) Update was finished. Click the OK button, update of ECU Reprogramming data is ended. Double-click the M.U.T.-III icon displayed on the desktop to start up the system. (Case B) Update was finished. Click the OK button, the PC is rebooted automatically. After rebooting the PC, Double-click the M.U.T.-III icon displayed on the desktop to start up the system. (5) Update is unnecessary The ECU Reprogramming data in M.U.T.-III is in the newest state. It is not necessary to update ECU Reprogramming data. Click the OK button, this update application is ended.
77
(3) Select System Function tab, and press ECU reprogramming button. Caution: -In case an update CD-ROM is set in the PC with update undone, data update starts. (refer to 9-3-1(4))
(4) Press Memory card transfer button. ALL reprogramming data in the M.U.T.-III PC are transferred to the memory card. Caution -Do not remove the memory card from PC.
button to start
78
(6) Press button when the message It transfers data to the memory card. Are you ready? appears
(7) Data transfer The progress bar is displayed during the transfer.
(9) Before you remove the memory card, double-click the below icon for removal of the adaptor.
(10) Select [PCMCIA IDE/ATAPI Controller] or the other appropriate device, then press Stop button.
79
(12) After displayed the message The device can now be safely removed from the system, push the lever on the side of PC card slot and remove the memory card. Caution: Do not remove the memory card away unless complete above method or turn off the PC.
80
(a). Automatic Data Retrieval (b). Select and Load Data (c). (Special case)
2 The appropriate reprogramming data file No. is displayed. Pressing Enter key starts transferring the data file into V.C.I built-in-memory. Remark: To search another data, press Esc key. If another appropriate reprogramming data exist, it will be displayed. The message bellows are displayed depends on ECU parts No, ROM-ID and condition of ECU. Press Enter Key to move back to Main menu. (a) No update data in PC card This message appears if no pertinent reprogramming data exists. No data will be transferred. (b) ECU at current level of VCI This message appears if the ECU has been already reprogrammed. No data will be transferred.
Loading****
ECU Reprogramming
(4) After completing data transfer, ECU reprogramming starts sequentially. For next steps, refer to 9-4-4.
81
(2) Select a reprogramming data file by key, and press Enter key. Esc key Move back to main menu. Remark: -The data files are displayed in numeric order of data No.. (From big to small; new to old) (3) Reconfirm the data file No., and press Enter key to start transferring the data into V.C.I. built-in-memory. Esc Key Cancel (4) Progress is displayed on monitor * mark is increased by steps.
Loading ****
ECU Reprogramming
(5) After completing data transfer, ECU reprogramming starts sequentially. For next steps, refer to 9-4-4.
ECU Reprogramming
82
(1) ECU parts No. and ROM-ID No. are displayed. Press Enter key to start reprogramming. ESC / key : restart V.C.I. * : By pressing key, immediately move to next.
Note: - Reprogramming must carry out on the condition of engine stop and IG switch on. - Do not disconnect harness/ turn off the IG switch during ECU reprogramming.
a) RPG data doesnt apply to ECU Reprogramming stopped owing to the data in V.C.I. memory being not appropriate for the ECU. Note down the displayed ECU parts No. and ROM-ID. Restart V.C.I. by pressing Enter key, and confirm the matching of the data file No, which is displayed by reboot, and the ECU part No./ ROM-ID for reprogramming.
ECU same as VCI CK for new data Auto change in 4 sec Part# MD351868 ROM-ID 120926 Auto change in 4 sec Turn IG SW OFF, please wait... Auto change in 4 sec
b) ECU same as VCI, CK for new data (CK; check) Reprogramming stopped because reprogramming has been already done.
83
In Progress STEP1 ....... In Progress STEP2 ......... In Progress STEP3 ......... In Progress STEP4 ......... In Progress STEP5 .........
(2) 5 steps progress is displayed while reprogramming. Caution: Do not press any key during reprogramming automatically proceeding. Do not turn off V.C.I power or IG switch during reprogramming. STEP1: Saving the data to the back up memory. STEP2: Erasing data in ECU. STEP3: Writing reprogramming data STEP4: Verifying the data between ECU and V.C.I. STEP5: Erasing diagnosis code and back up memory
3 On completion of the 5steps, new reprogrammed ECU parts No. and ROM-ID are displayed. Turn IG switch LOCKOFF. Note: Diagnosis code might be memorized in ECU if without turning IG switch Lock (off)
4 ECU reprogramming completed Verify the system properly operated by starting engine. Enter key: V.C.I. restart
84
(2) Press
ECU Reprogramming
button.
(3) Select an appropriate button. Automatic Reprogramming (K-line) -- to 9-5-2(a) - Automatically searches appropriate Reprogramming data stored in PC. Database File Display -- to 9-5-2(b) - Shows the list of Reprogramming data stored in PC. Reprogramming Data Selection -- to 9-5-2(c) - Allows selecting Reprogramming data in arbitrary drive and directories. Search -- to 9-5-2(d) - Allows searching the target data by ECU No., ROM-ID, etc. $ Connect PC and V.C.I., and prepare following steps. 1. Connect M.U.T.-III Main Harness B or A to V.C.I. securely. 2. After verifying the ignition switch position at LOCK (OFF), connect the M.U.T.-III Main harness B or A to the vehicles diagnosis connector. 3. Turn Ignition switch on, and turn V.C.I. main switch on. (Do not start engine)
85
(a). Automatic Data Search (b). Database File display (c). Reprogramming Data Selection (d). Search
(2) Result of the search appears. Select an appropriate data file with scrolling the list using buttons, and press button to start transferring the data into V.C.I. memory. -After completing the data transfer, ECU reprogramming will start sequentially. (refer to 9-5-3.) Note: Press OK button when message window of device removal warning comes out at start and end of data transfer.
86
(c). Reprogramming Data Selection To select the reprogramming data from arbitrary directories.
(1) Press Reprogramming Data Selection button on the function menu, then the left screen appears. -- to select arbitrary drive and directory " (2) On this screen, select an appropriate data file and press to start transferring the data into V.C.I memory. Note: -The displayed data as default is in the folder shown below. C:Program FilesMUT3RPGDATA This directory is the default reprogramming data pool of M.U.T.-III, referred from 9-4-1, 9-5-2(a),(b),(d). -After completing the data transfer, ECU reprogramming will start sequentially. (refer to 9-5-3.) (2) Data selection Select a drive on the left chart, and the directories in the drive are displayed on the right chart. -To move to a lower directory, select appropriate row on the right chart and press button. -To move to an upper directory, select row on the right chart and press button. Select appropriate directory name row on the right chart, and press button to return to (1) and list the files contained in the directory.
87
(d). Search To search the reprogramming data by inputting ECU Part No., ROM-ID, or Data No.
(1) Press Search button on the function menu, then the left screen appears. Input search key info in the input column, then press button. Note: To input, 2 ways can be taken. -By PC keyboard -By virtual keyboard --press Some info need to be a combination with the other info for data search - Current ECU P/N & ROM-ID need to be together. - Data No. needs no other info. (2) Results Select appropriate data with scrolling the list using buttons and press button to start transferring the data into V.C.I memory. --10 lines scrolling -After completing the data transfer, ECU reprogramming will start sequentially. (refer to 9-5-3.) Note: Press OK button when message window of device removal warning comes out at start and end of data transfer.
88
(2) Press
ECU reprogramming
button.
(3) Press Automatic Reprogramming (CAN) button. Note: Other 5 buttons are for K-line system and not for CAN system.
(4) Vehicle choice -Selected Model year and Model Code of the vehicle are indicated. -Select a system (ECU) and loading option, and press button. -If you select other Model year and Model code, press button and select model.
button.
89
Unnecessary reprogramming
Complete reprogramming
(7) Data check -The appropriate reprogramming data is indicated. -Press button to go to next.
(8) Reprogramming data check -Check and press button. -If you select other repro. data, press
button to back.
(10) Reprogramming completed -Reprogramming is completed properly. -Reprogrammed ECU Part No. and S/W Part No. are indicated. -Press button, and turn IG switch OFF.
90
Troubleshooting of Reprogramming
Troubleshooting of Reprogramming
No.
Cause/Remedy <Cause> ' There is no ECU for requiring reprogramming ' IG switch not positioned ON. ' Main Harness not connected.
<Remedy> 1. Turn off the V.C.I. power. 2. Verify the connection of harness, and condition of harness itself. 3. Verify if the ECU for required reprogramming is installed. 4. Verify if the ECU can communicate with V.C.I. 5. Then redo the procedures. <Cause> There is no reprogramming data in memory card although ECU is affected for reprogram. <Remedy> 1. Press the V.C.I. Enter key and back to Main menu. 2. Turn off the V.C.I. and eject the memory card from V.C.I.. 3. Insert the memory card into M.U.T.-III (PC), and transfer the data to the card. Then retry the procedure. <Cause> Failure of data transfer from memory card to V.C.I.. <Remedy> 1. Press the V.C.I. Enter key and back to Main menu. 2. Retry Automatic RPG or Load RPG again.
CK VNxxxxx.rpg In PC card
Load error
< Cause > Model specifying information (Model Year, Type, Class) is insufficient. < Remedy > Select vehicle type again.
< Cause > No CBF file exists in PC. < Remedy > Reinstall M.U.T.-III.
92
Troubleshooting of Reprogramming
No. 4
Message
Cause/Remedy < Cause > Connection between V.C.I. and vehicle malfunctioned. The power switch of V.C.I. is OFF.
< Remedy > Confirm connection between V.C.I. and vehicle. Confirm the power switch of V.C.I.
< Cause > No reprogramming data (CFF file) exists in PC. < Remedy > Reinstall reprogramming data (CFF file).
< Cause > While reprogramming, an error occurred. < Remedy > Restart reprogramming process from beginning.
< Cause > Diagnosis code couldn't be erased. < Remedy > Erase the DTC by diagnosis function of M.U.T.-III.
< Cause > An error occurred reprogramming data. < Remedy > Reinstall M.U.T.-III.
in
accessing
database
to
search
< Cause > The internal process error occurred on database to search the reprogramming data. < Remedy > Reinstall M.U.T.-III.
93
Troubleshooting of Reprogramming
12
< Cause > Application was started during M.U.T.-III starting. < Remedy > Please insert CD-ROM in a PC again after terminating M.U.T.-III.
13
< Cause > M.U.T.-III system is not installed in the PC. < Remedy > Please use the PC with which M.U.T.-III were installed.
14
< Cause > OS installed in the PC is except Windows2000 or WindowsXP. < Remedy > Please use the PC with which Windows2000 or WindowsXP was installed.
15
< Cause > It started by users other than "Administrator" or "mut". < Remedy > Please log in and start by the user of "Administrator" or "mut".
94
(2) Function Selection Measurements in Real-time -- to 10-1-2. Data Display -- to 10-1-3. Analyze -- to 10-1-4. Print out -- To print out the view graph. Data storing -- To load the data, which is stored in a removal disk, onto the PC.
95
(3) View Graph The data of 4 items/4 graphs are displayed. -Pressing button stops recording. -Once recording has been stopped, the data is automatically saved. --View Text To (4). Note: The file name is set as FU+Year Month Day+Time (military time including seconds). (4) View Text --View Graph To (3) --Stop Record
(2) View Graph The data of 4 items/4 graphs are displayed. Pressing buttons or moving the slide bar displays the value of the cursor line. --View Text To (1) --Change displayed Unit
96
97
(2) Put the pressure gauge on the fuel pipeline. Press Fuel Pressure Measurement on the menu screen of 10-1-1(1). The selection screen of pressure gauge appears. Select a pressure gauge and press button.
(3) Entering the Calibration value Enter the calibration volt which you measured in (1), and press button.
(4) Measuring Fuel Pressure The measured value is displayed on the graph.
98
This function allows you to observe the continuous waveform, which is loaded from the voltage measurement terminal, on PC screen using test leads (MB991499, etc). --Starts the waveform display --Stops the waveform display --Switches to Scale mode : to set the time axis and voltage axis --(2) --Switches to Trigger mode : to set trigger conditions --(3) Note: DC voltage can be measured in the range of 0-40V, and resolution can be measured at 0.1V. The shortest sampling interval is 500s. (2) Setting the Time Axis and Voltage Axis button switches to the scale mode, and the buttons can be used to set time axis and voltage axis. --Changes time axis scale --Changes voltage axis scale Note: Time scale: (10,20,40,100ms/div) Voltage scale: (1,2,5,8V/div) (3) Setting Trigger Conditions button switches to the trigger setting mode, and a trigger point can be changed by the buttons. --Up Trigger --Down Trigger
99
No.
Message/Symptom
Cause
Remedy
1. Verify that the V.C.I. switch is ON. 2. Verify the vehicle battery is sufficiently charged (12V). 3. Disconnect and reconnect the connector. 4. Check if there is a short in the harness. (Try using a different harness.) 5. If the problem is not resolved by remedies 1-4, there may be a hardware error. Request inspection with the harness. 1. Verify that PC is ON.
Vehicle power supply failure due to: The V.C.I. does not ' V.C.I. switch turned power up when OFF connected correctly to ' Low battery the vehicle. Be sure ' Vehicle harness not the IG switch is ON. connected or a short exists ' Hardware error
PC power supply failure due to: The V.C.I. does not ' PC power not power up from the PC activated connection with the ' USB cable not USB cable. V.C.I. is connected or a short not connected to exists vehicle at this time. ' Hardware error (PC or V.C.I.)
2. Verify that appropriate USB cable is firmly connected between the PC and V.C.I. (Do not use a USB hub.) 3. Disconnect and reconnect the connector. 4. Check if there is a short in the cable. (Try using a different harness.) 5. If the problem is not resolved by remedies 1-4, there may be a hardware error. Request inspection with the PC. 1. Turn the V.C.I. OFF. 2. Disconnect USB cable and connector.
The screen Maintenance Mode appears as soon as the V.C.I. is powered up.
3. Turn the V.C.I. power ON. (Do not touch Esc key.) V.C.I. was powered on with pressing Esc key. 4. If the Main Menu or PC Communication display does not appear, the V.C.I. may be at fault. Request inspection.
100
No.
Message/Symptom
Cause
Remedy
1. Connect the unit to the PC (for power activation) while pressing the V.C.I. Esc key. 2. Verify that the V.C.I. screen display indicates Maintenance Mode. 3. In order to install the V.C.I. basic application, using the automatic version upgrade feature, start the PC M.U.T.-III diagnostic application and attempt diagnosis. (refer to 3-3-1) 4. As Setup V.C.I. dialog box appears on PC screen during the diagnosis, press button. 5. When Update dialog box disappears on PC screen, the install is completed. 6. If, once the application has been downloaded and the V.C.I. power has been reactivated, the Main Menu or PC Communication display does not appear, request inspection.
The screen ECU Reprogramming appears as soon as the V.C.I. power is activated.
The screen Drive Recorder [1] Record error appears during recording the Drive recorder with V.C.I. alone.
Communication error
1. Press the V.C.I. Enter key. 2. Verify that the V.C.I. screen display indicates Drive Recorder Continue? , press the Enter key or wait 10seconds to start recording again.
101
102
<<Terminology>>
Appendix
<< Terminology >>
In alphabetical order A AMT: Abbreviation for Automated Manual Transmission Electronic Controlled Unit. ASC: Abbreviation for Active Stability Control System. C CAN: Abbreviation for Controller Area Network. A system that shares data between ECUs through communication. The processing of each command (signal) is possible using a communication line only. D Data transmission: The transmission of data stored from one memory area to another memory area. In the case of M.U.T.-III, this refers to the transmission of data from the V.C.I. memory area to the PC. Default: Initial setting. A predetermined value that is set when an item that should be defined is not defined. Diagnosis: Refers to the self-diagnosis function. A system in which the ECU installed in the vehicle monitors input signals from the various sensors and switches and, when an error occurs or erroneous information is identified, records the data in memory. E ECU: Abbreviation for Electronic Control Unit. The control unit of the electronic control system. EPS: Abbreviation for Electric Power Steering iIi I/F cartridge: A cartridge used when the ECU communication method employed is a special method or when M.U.T.-III functions have been expanded and support is not possible by the M.U.T.-III unit alone. The various I/F cartridges, such as the cartridge for the SWS monitor set in M.U.T.-II or the cartridge for DCC communication, can be used as is. M Memory card: A medium used to store data. Records data such as those used for ECU updates. With M.U.T.-III, flash memory is employed which allows the user to electrically change the data as well as maintain the information even if the power is turned off. Batteries are not required.
103
<<Terminology>>
O Online help: Also referred to as the online manual. An operation manual loaded on M.U.T.-III, which gives easy-to-understand explanations on how to use the various functions. how to perform an operation during application use. R RAM: Abbreviation for Random Access Memory. A memory device that is capable of both read and writes operations. The information stored in this device is lost when the power is turned off. ROM: Abbreviation for Read Only Memory. A memory device that is capable of read operations only. The information stored in this device is maintained even when the power is turned off. S Serial communication: A method in which the bits that make up digital data are transmitted in series one bit at a time on the communication line. The reading of diagnostic code via communication from the ECU using the M.U.T. is referred to as Pattern Diagnosis. Slide bar: A method in which a value is entered by moving a bar. SWS: Abbreviation for Smart Wiring System. A system that centrally controls multiple electrical signals on one harness, thereby minimizing the number of harnesses used. The SWS lead to the development of the multiplex transmission system, making harness weight reduction and the development of multifunctional electrical components possible. V V.C.I.: Abbreviation for Vehicle Communication Interface. The communication interface used to connect the ECU mounted in the vehicle with a PC. It also provides processing methods related to the operation currently performed when the user is unsure
104
Home
OK or YES
Previous page
Cancel
Next page
Help
Record end
Print screen
Manual trigger
Information
Displays information.
Transmit data
Transmits the data of the selected block to the PC. Saves the selected data files to a removable disk. Opens the alphanumeric input screen. Jumps to the trigger point.
View Displays vehicle information. vehicle information Erase Erases diagnosis data
Save data
History
Displays history of vehicle information settings. Displays four items on four graphs. Displays (overwrites) four items on one graph. Displays text.
View graph1
View graph2
Data search settings Opens the search condition setting screen. Correlation chart Opens the correlation chart setting screen. Opens the distribution chart setting screen. Opens the Time extraction/search condition setting screen. Change of function button (1/2 display)
View text
Changes the graph display time scale. Changes the graph display data scale.
Distribution map
Time setting
Select item
1/2
Sort
2/2
Change of function button (2/2 display) Change of function button (1/3 display) Change of function button (2/3 display) Change of function button (3/3 display)
Run
1/3
Stop
2/3
Pause
Pause
3/3
105
Button Image
Button Image
Disconnect cartridge Disconnects the SWS monitor cartridge. Start diagnosis Starts diagnosis and displays the result.
Enter
Down arrow
Down arrow Key function of V.C.I. Displays bookmarks (pages with bookmarks). Displays MSB to check revision points of the Service manual. Displays document information.
Bookmark
Corrects the calibration on measurement function. Changes the displayed unit of measurement. Changes the scale.
View MSB
Change scale
Trigger setting
Sets the Oscilloscope function trigger. Generates a trigger at the time of a rise. Generates a trigger at the time of a fall. Opens the drive selection screen. Opens the selected folder.
Search List
Returns the screen to the search list screen. Returns the screen to the list of the presently displayed groups (or to the list of reference Returns the screen to the previously displayed screen. Enlarges the display.
Up trigger
Group top
Down trigger
Previous display
Select drive
Zoom in
Select folder
Zoom out
106