KDC 248 U
KDC 248 U
KDC 248 U
KDC-248U
KDC-208U
KDC-MP248U
KDC-MP148U
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D'EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Kenwood Corporation
US Residents Only
2
Downloaded from www.Manualslib.com manuals search engine
Preparation Iii.
~It.
'0:1
• Do not expose the faceplate to direct
sunlight, excessive heat, or humidity. Also
CALIFORNIA, USA ONLY
avoid places with too much dust or the
This perchlorate WARNING applies only
possibility of water splashing.
to the product sold or distributed in
• Keep the faceplate in its casing while
California USA "Perchlorate Material-special
detached.
handling may apply, See www.dtsc.ca.gov/
• The faceplate is a precision piece of
hazardouswaste/perchlorate:'
equipment and can be damaged by shocks
or jolts.
Caution:
• To prevent deterioration, do not touch the
• Do not set the remote control in hot places
terminals of the unit and faceplate with
such as on the dashboard.
your fingers.
• Lithium battery.
Danger of explosion if the battery is
How to reset your unit
incorrectly replaced. Replace only with the
If this unit fails to operate properly, press the same or equivalent type.
reset button. • The battery pack or batteries shall not be
exposed to excessive heat such sunshine,
The unit returns to factory fire or the like.
settings when the reset • Keep battery out of reach of children and in
button is pressed. original package until ready to use. Dispose
of used batteries promptly. If swallowed
Reset button
contact physician immediately.
~
o 0O(Q)
0000
OOO(Q)
3
Downloaded from www.Manualslib.com manuals search engine
Basic operations
Loading slot
.-···
KDC-248U/ KDC-MP248U KDC-208U/ KDC-MP148U
iPod Auxiliary input jack -":---'l
.. ----
3 (ALL ROM) 3
5 (MEMO MY U5n 5
4
Downloaded from www.Manualslib.com manuals search engine
When you press or hold the following button(s)...
• Turns on.
• Turns off if pressed and held.
<!> SRC Selects the available sources (TUNER, USB or iPod, CD, AUX,
STANDBY), if the power is turned on.
SRC
• If the source is ready, playback a/so starts. "iPod" or "COIl is
selectable only when an iPod is connected or a disc is loaded.
5
Downloaded from www.Manualslib.com manuals search engine
Getting started
Canceling the display Adjusting the clock
demonstration 1 Press the volume knob to enter
The display demonstration is always turned [FUNCTION] mode.
on unless you cancel it. 2 Turn the volume knob to select
[SETTINGS], then press to enter.
When you turn on the power (or after you
3 Turn the volume knob to select [CLOCK],
reset the unit), the display shows:
then press to enter.
[CANCEL DEMO] .. [PRESS] ..
4 Turn the volume knob to select
[VOLUME KNOB]
[CLOCK ADJ], then press to enter.
1 Press the volume knob. Clock hour flashes on the display.
[YES] is selected as the initial setup. S Turn the volume knob to adjust the
2 Press the volume knob again to confirm. hour, then press to enter minute
[DEMO OFF] appears. adjustment.
• If no operation is done for about Clock minutes flashes on the display.
15 seconds or if you turn the volume knob 6 Turn the volume knob to adjust the
to select [NO] in step 2, [DEMO MODE] minute, then press to confirm.
appears and the display demonstration Press ~ / ~ to move between the
starts. hour and minute adjustment.
7 Hold ~ to finish the procedure.
Setting the demonstration mode
1 Press the volume knob to enter Initial settings before operations
[FUNCTION]. 1 Press ~ SRC to enter [STANDBY] mode.
2 Turn the volume knob to select 2 Press the volume knob to enter
[DEMO MODE], then press to enter. [FUNCTION] mode.
3 Turn the volume knob to select [ON] or 3 Turn the volume knob to select
[OFF]. [INITIAL SET], then press to enter.
If [ON] is selected, display demonstration 4 Turn the volume knob to make a
starts if no operation is done for about selection, then press to confirm.
20 seconds. See table below for selection.
4 Hold ~ to finish the procedure. S Hold ~ to finish the procedure.
Co .··!I~~~~~;~~i1f~g;r((~$~j;~~~i~f~~~~%.~:·1~,:f~:~~-~;·1~f:~2;:;ji:~ftf;:
PRESET TYPEl NORM*: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM).;
___ MIX: Me.,r:norizes one station for each preset button regardless of the selected band (FMl / FM2/ F~.~L~~_
KEY BEEP ON*/ OFF: Activates/deactivates the keypress tone.
BUilTIN AUX ONl *: Outputs sound of the connected external component through the car speakers when AUX" is selected
II
as the source. ; ON2: Outputs sound from the connected external component when AUX" is selected as the
II
source. When you turn on the power, the sound attenuates (to prevent noise when no external component is
connected). Turn the volume knob clockwise to return to the previous volume level. ;OFF: Disables AUX" in
II
source selection.
CD READ 1*: Automatically distinguishes between audio file disc and music CD. ; 2: Forces to playas amusic CD. No
__
sound can be heard if an audio .file disc --:.-.-:..-_-----------_.
is played.
6
Downloaded from www.Manualslib.com manuals search engine
SWITCH PRE REAR*1SUB-W: Selects whether rear speakers or asubwoofer are connected to the line out terminals on the
rear of the unit (through an external amplifier).
SP SELECT IOFF*1 5/41 6 x 9/6/ OEM: Selects the speaker size for optimum performance.
F/W UP xX.xx IYES: Starts upgrading the firmware. ; NO*: Cancels (upgrading is not activated).
For details on how to update the firmware, see: www.kenwood.com/cs/ce/
'::Jlf~;$f'~.
Selects the tuning mode for ~ I ~ buttons.
AUTOl *: Automatically search for astation. ; AUT02: Search in the order of the stations in the preset
memory. ; MANUAL: Manually search for astation.
AUTO MEMORY YES: Automatically starts memorizing 6stations with good reception. ; NO*: Cancels (automatic
_ _~ not activated). (Selectable only if [NORM] is selected for [PRESET TYPE].) (page 6)
MONO SET !ON: Improve the FM reception (but the stereo effect may be lost).; OFF*: Cancels (stereo effect resumes).
Using the remote controller (RC-40S)
FM+ / AM- : Selects band.
~ 1 ~ (+) : Selects station.
1- 6 : Selects preset station.
USB terminal
r-·············· __ ·_--········-_··················.
Connecting an iPod
I About Audio file (KDC-248U/ KDC-MP248U only)
I- Playable Audio file: MP3 (.mp3), WMA
(.wma)
- Playable disc media: CD-R/RW/ROM
- Playable disc file format: ISO 9660 Level
1/2, Joliet, Romeo, Long file name.
- Playable USB device file system: FAT16,
FAT32
Although the audio files are complied
with the standards listed above, the play
maybe impossible depending on the The source automatically switches, and
types or conditions of media or device. playback starts.
... _-- -............••.....•....•... _-
8
Downloaded from www.Manualslib.com manuals search engine
Selecting Repeat Play Selecting a folder/tracklfile
Press number button 4 (REP) repeatedly 1 Press ~ to enter Music Search mode.
to make a selection. "SEARCH" appears, then the current file
name appears on the display.
Audio CD: TRAC (track) REPEAT, REPEAT OFF
2 Turn the volume knob to select a folder/
MP3IWMA:
track/file, then press to confirm.
FILE REPEAT, FOLD (folder) REPEAT,
REPEAT OFF • To return to the root folder (or first track for
iPod : FILE REPEAT, REPEAT OFF audio CD), press BAND.
• To return to the previous folder, press~.
Selecting Random Play • To cancel the Music Search mode, press
Press number button 3 (ALL ROM) or X and hold~.
repeatedly to make a selection. • < or > on the display indicates that
preceded/next item is available.
Audio CD : DISC RANDOM, RANDOM OFF • For USB device* and iPod: To skip search,
MP3IWMNiPod : press~/~.
FOLD (folder) RANDOM, RANDOM OFF * This operation is effective only for the files
• Press and hold number button registered in the database created with
3 (ALL ROM) or X to select Kenwood Music Editor. (page 10)
"ALL RANDOM:' • KDC-248U/ KDC-MP248U only: To return to the
- Applicable only if"RANDOM OFF" is top menu while in the search mode of an
selected initially. iPod, press BAND.
- KDC-248U/ KDC-MP248U only: Changes the
iPod browsing item to "songs:'
Direct Music Search using the
remote controller (RC-405)
Selecting Scan Play
• Not available if Random Play, Scan Play, or
Press number button 2 (SCAN)
iPod playback is selected.
repeatedly to make a selection.
1 Press DIRECT to enter Direct Music
Audio CD :TRAC (track) SCAN, SCAN OFF Search Mode.
MP3IWMA: FILE SCAN, SCAN OFF "- _ -" appears.
• If scan play is selected, the unit starts 2 Press the number buttons to enter the
playing the first 1O-second intra of the track number.
music in the disc/current folder. 3 Press ~ / ~ to search for the music.
If"SCAN OFF" is selected, the unit resumes
• To cancel the Direct Music Search Mode,
normal play of the current song.
press ~ or EXIT.
I.
Discs that cannot be used
• Discs that are not round.
Discs with coloring on the recording
l Functions of KOC-248U/ KOC-MP248U with iPod
~I -
to display the playlist. About co~-p~tible iPod/iPhone
"MY PLAYLISr appears. Made for
2 Turn the volume knob to select the song I - iPod touch (3rd generation)
you want to delete, then press and hold iPod touch (2nd generation)
the volume knob. I - iPod touch (1 st generation)
3 Turn the volume knob to select I - iPod classic
"DELETE ONE" or "DELETE ALL/' then i - iPod with video
press to confirm. - iPod nano (5th generation)
Select "DELETE ALL" to delete all the songs - iPod nano (4th generation)
in the playlist. - iPod nano (3rd generation)
4 Turn the volume knob to select "YES," - iPod nano (2nd generation)
then press to confirm. - iPod nano (1 st generation)
"COMPLETE" appears. - iPhone 4
- iPhone 3GS
iPod control by Hand Mode - iPhone 3G
Press and hold iPod to enter iPod mode. -iPhone
• For the latest compatible list and
HANDSON:
software version of iPod/iPhone, see:
Control iPod from the iPod. "iPod MODE"
www.kenwood.com/cs/ce/ipod
appears on the display.
• If you start playback after connecting the
HANDS OFF: Control iPod from the unit.
I iPod, the music that has been played by
the iPod is played first.
Adjust [SETTINGS] mode settings In this case, "RESUMING" is displayed
While listening to an iPod... without displaying a folder name, etc.
1 Press the volume knob to enter Changing the browse item will display a
[FUNCTION] mode. correct title, etc.
2 Turn the volume knob to select • You cannot operate iPod if "KENWOOD"
[SETTINGS], then press to enter. or "./" displayed on iPod.
3 Turn the volume knob to make a
selection, then press to confirm.
See the following table for selection.
4 Hold ~ to finish the procedure.
-
~:=:::::>"'"' -',
~~~~~~~~~~~~~~~~~~~~~~~~~lE~~~ ...
··
··
..····
1 Press <!> SRC to select AUX." II
Auxiliary input jack
2 Turn on the external component and
start playing.
3 Turn the volume knob to adjust the
.....
volume.
r-------'------.~--- -----··-··-1
Maintenance
Cleaning the unit: Wipe off the dirt on the panel with a dry silicon or soft cloth. Failure to I
observe this precaution may result in damage to the monitor or unit.
!
I Cleaning the connector: Wipe off dirt on the connector of the unit and faceplate. Use a I
I
cotton swab or cloth. i
Handling discs
- Do not touch the recording surface of the disc.
- Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
- Do not use any accessories for the disc.
I - Clean from the center of the disc and move outward. I
- Clean the disc with a dry silicon or soft cloth. Do not use any solvents.
I
I - When removing discs from this unit, pull them out horizontally.
I- Remove the rims from the center hole and disc edge before inserting a disc.
12
Downloaded from www.Manualslib.com manuals search engine
Function settings
1 Press the volume knob to enter [FUNCTION] mode.
2 Turn the volume knob to select [AUDIO CTRL] or [SETTINGS], then press to enter.
3 Turn the volume knob to make a selection, then press to confirm.
• See table below for selection.
• Repeat step 3 until the desired item is selected/activated.
• Press ~ to return to the previous item.
4 Hold ~ to finish the procedure.
[AUDIO CTRL] : While listening to any source except in STANDBY state...
~~=.,.,...."".-=-',."".,."=~".....,..",.,....,...,,.~==..,.........,,=
______L
I
(Preset: 0) each source. The volume level will automatically increase or decrease when you change the
source. (Before making an adjustment, sele~~the sourc~Jou ~ant t~ adjus.t.)
• [SUB-W LEVEll SUB-W SETI LPF SUB-WI SUB-W PHASE] is selectable only if [SWITCH PRE] is set to [SUB-W]. (page 7)
• [5UB-W LEVEll LPF SUB-W/ SUB-W PHASE] is selectable only if [SUB-W SET] is set to [ON].
[SETTINGS]
AUX NAME AUX* I DVDI PORTABLEI GAMEl VIDEOI TV: Selects the desired name for the connected component.
(Selectable only if"AUX" is selected as the source.)
CLOCK CLOCK ADJ: (For details, see page 6.)
DISPLAY DIMMER SET: ON: Dims the display illumination. ; OFF*: Cancels.
TEXT SCROLL: AUTO*I ONCE: Selects to scroll the display information automatically, or scroll only once. ;
OFF: Cancels.
"NO DEVICE" appears. No USB device is connected. Connect an USB device, and change the source to
I USB again.
-------------_.- - ._-----------
"NO MUSIC appears. The connected USB device contains no playable audio--_._----_
file. ..._-._--
"NA DEVICE" appears. I Connect asupported USB device, and check the connections. ,
"USBERROR"appea~. l Remove the USB device, turn the unit off, then turn it on again. If the unit sti II
----------
"iPod ERROR" appears.
Noise is generated. =i
Tracks cannot play back as you have
intended them to play.
showing the same display, try to connect another USB device.
..Beconne~t the iPod. / Confirm that the sohware !~r_!~~~d is th~te~_:::"t:!.~!.?~~ __
I Skip to another track or change the disc.
I Playback order is determined when files are recorded.
--_._-------
"READING" keeps flashing. Longer readout time is required. Do not use too many hierarchies and folders.
u , _
Elapsed playing time is not correct. This is caused by how the tracks are recorded.
-----_._--
The number of songs contained in "SONGS" Podcast files are not counted in this unit as this unit does not support the
category of this unit is different from that I
playback of podcast files.
contained in "SONGS" category of iPoU
Correct characters are not displayed (e.g. \ This unit can only display letters (upper case), numbers, and alimited number
album name). ~ of symbols.
14
Downloaded from www.Manualslib.com manuals search engine
Specifications
FM tuner section Audio section
Frequency range: Maximum output power: 50 W x 4
For KDC-248UI KDC-208U: Full bandwidth power (at less than 1%THD):
200 kHz space: 87.9 MHz - 107.9 MHz 22Wx4
For KDC-MP248UI KDC-MP148U: Speaker impedance: 4 0 - 8 0
50 kHz space: 87.5 MHz - 108.0 MHz Tone action: Bass: 100 Hz ±8 dB
Usable sensitivity (SIN= 26 dB): Middle: 1 kHz ±8 dB
11.2 dBf (1.0 IJV175 0) Treble: 10kHz ±8 dB
Quieting sensitivity (DIN SIN = 46 dB): Preout level I load (CD): 2 000 mVil 0 kO
19.2 dBf (2.5 IJVl75 0) Preout impedance: $ 600 0
Frequency response (±3 dB): 30 Hz - 15 kHz
Signal-to-Noise ratio (MONO): 63 dB Auxiliary input section
Stereo separation (1 kHz): 40 dB Frequency response (±3 dB): 20 Hz - 20 kHz
Input maximum voltage: 1 200 mV
AM tuner section Input impedance: 10 kO
Frequency range (10kHz space):
530 kHz - 1 700 kHz General
Usable sensitivity (S/N= 20 dB): 31 dBIJ (36 IJV) Operating voltage (11 V- 16 Vallowable): 14.4 V
Maximum current consumption: lOA
CD player section Installation size (W x Hx D):
Laser diode: GaAIAs 182 mm x 53 mm x 158 mm
Digital filter (D/A): 8 Times Over Sampling (7-3/16" x 2-1/8" x 6-1/4")
D/A converter: 24 Bit Weight: 2.91bs (1.3 kg)
Spindle speed: 500 rpm - 200 rpm (CLV)
Wow &Flutter: Below Measurable Limit Subject to change without notice.
Frequency response (±1dB): 20 Hz - 20 kHz
Total harmonic distortion (1 kHz): 0.01 %
Signal-to-Noise ratio (1 kHz): 105 dB
Dynamic range: 90 dB
MP3 decode: Compliant with MPEG-1/2 Audio
Layer-3
WMA decode: Compliant with Windows
Media Audio
USB interface
USB standard: USB 1.1/2.0 (Full speed)
Maximum supply current: 500 mA
File system: FAT16/ 32
MP3 decode: Compliant with MPEG-l/2 Audio
Layer-3
WMA decode: Compliant with Windows
Media Audio
Kenwood Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS NO.21 CFR.
1040. 10, CHAPTER 1, SUBCHAPTER J.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly approved in the instruction manual. The user
could lose the authority to operate this equipment if an unauthorized change or modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment may cause harmful interference to radio communications, if it is not
installed and used in accordance with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radiolfV technician for help.
• "Made for iPod," and "Made for iPhone" mean that an electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this device or its compliance with safety
and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless
performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the u.s. and
other countries.
This symbol mark indicates that Kenwood manufactured this product so as to decrease
harmfu I influence on the environment.
------------------
Part list:
@ Faceplate ...
® Escutcheon...
(xl)
(Xl)
Liste de pieces:
@
®
Fa~de.........
teusson
(Xl)
(xl)
listQ de componentes:
@ Plaea frontal....
® Escudere ...
(Xl)
(xl)
© Mounting sleeve ..... (xl) © Manehon de montage....... (xI) © Manguito de manraje... (Xl)
@ Casing for faceplate ... (Xl) @ Boilier pourla fa~de (xI) @ Esruehe de 10 placa frantal . (xl)
® Wiring harness... (xl) ® Q.blage eleetrique.......... (Xl) ® Mazo de cand uerores (Xl)
® Removal tool ... (x2) ® Dutil de demontage (x2) ® Herramiera de exrracei6n .... (xl)
@ Flat head screw (for Nissan cars) . (x4) @ Vis a tete plate (pour les voitures Nissan) (x4) @ Tamillo de cabeza plana (para los aurom6viles Nissan)..... (x4)
® Round head screw (for Toyota cars) ... (x4) ® Vis atete ronde (pour les voitures Toyota) (x4) ® Tornillo de cabeza redondo (para los auram6viles Toyora).... (x4)
,War.,ln,1 A)(ertls~ent I Adv,el1lmC!., "" rtf- g' 'j' '''')'1 '@g) 'r , r t' 6_$ g (', ·'t" , ,
• The unit can only be installed in a car with a 12 V DC power • L'appareil peut uniquement etre installe dans une voiture avec • La unidad solo puede instalarse en un autom6vil con (uente de
supply, negative ground. une alimentation de 12 V CC, amasse negative. alimentaei6n de 12 VCC con mma negativa.
• If you connect the ignition wire (red) and the battery wire (yellow) • Si vous connectez Ie cable d'allumage (rouge) et Ie cable de • 5/ eoneera el cable de encendido (rojo) y el cable de 10 borerlo
to the car chassis (ground), you may cause a short circuit, that in batterie (jaune) au chassis de la voiture (masse), vous risquez (amarillo) al ehas/s del autom6vil (tierra), podrla produeir un
turn may start a fire. Always connect those wires to the power de causer un court-circuit qui peut provoquer un incendie. cortocircuiro y esto a su vez, un incendio. Conecte siempre esos cables
source running through the fuse box. Connectez toujours ces cables a1a source d'alimentation passant ala fuente de alimentaci6n que pasa par 10 caja de fusibles.
• Disconnect the battery's negative terminal and make all electrical par Ie boitier de fusibles. • Desconecte el terminal negativo de 10 baterfa y realice todas {as
connections before installing the unit. • Deconnectez la borne negative de la batterie et realiser toutes les conexiones electricas antes de instalar la unidad.
• Insulate unconnected wires with vinyl tape or other similar connexions avant d'installer l'appareil. • Enrolle los cables no coneetados can una cinta de vinilo uotro
material. If no connections are made. do not let the wire come • Isolez les cables non-connectes avec un ruban de vinyle ou d'un material similar para que queden ais/ados. Si no se efectuan las
out from the tab to prevent short circuit. autre materiel similaire. Si aucune connexion n'est faite, ne conexiones, no deje que el cable sobresalga de 10 lenguera para evitar
• Be sure to ground this unit to the car's chassis again after laissez pas Ie fil sortie de la languette pour eviter tout court- cortocircuitos.
installation. circuit. • Asegurese de volver a conectar amasa esta unidad 01 chasis del
• Assurez-vollS de raccorder de nouveau la mise ala masse de cet autom6vil despues de la instalaei6n.
appareil au chassis de 1a voiture apres l'installation.
.C11
• If your car's ignition does not have an ACC position, connect the • Si I'allumage de votre voiture n'a pas de position ACe, • 5i el encendido de su autom6vil no esra provlsto de la pasiei6n ACe,
ignition wires to a power source that can be turned on and off connectez Ie cable d'allumage aune source d'alimentation qui conecte los cables de encendido a una Fuente de alimentaci6n que
with the ignition key. If you connect the ignition wire to a power peut etre mise sous et hors tension avec la clef de contact. Si pueda coneerarse y desconeetarse con 10 /lave de eneendido. 5i
source with a constant voltage supply, as with battery wires, the vous connectez Ie cable d'allumage aune source d'alimentation conecta el cable de encendido a una (uente de afimeRtaci6n que
battery may die. constante, comme un cable de batterie, la batterie risque de se recibe un suministro constante de afimentaci6n tales como los cables
• Do not use your own screws. Use only the screws provided. deeharger. de la barerla, la barerla podrla descargarse.
• Install this unit in the console of your vehicle. Make sure the • N'utilisez pas vos propres vis. N'utilisez que les vis fournies. • No utifice sus propios tomil/os. Otifice s610 los tomil/os incfuidos.
faceplate will not hit the lid of the console (if any) when closing • Installez cet appareil dans la console de votre vehicule. Assurez- • Instale esta unidad en 10 consolo de su vehfcu{o. Asegurese de que 10
and opening. vous que la fac,:ade ne heurtera pas Ie couvercle de la console (s'il placa fronral no golpee 10 rapa de la consolo (si 10 hubiera) cuondo 10
• After the unit is installed, check whether the brake lamps, blinkers, yen a) lors de sa fermeture ou de son ouverture. abre y la cierra.
wipers, etc. on the car are working properly. • Apres avoir installe l'appareil, verifiez si les lampes de frein, • Despues de insralar 10 unidad, compruebe que laslamparas de
• Mount the unit so that the mounting angle is 30° or less. Ies indicateurs, les dignotants, etc. de la voiture fonctionnent freno, las luces intermitentes, ellimpiaparabrisas, etc. funcionen
• If the fuse blows, first make sure the wires are not touching to correctement. satis(actoriamente.
cause a short circuit, then replace the old fuse with one that has • Monter l'unite de fac,:on ace que l'angle de montage soH de 30· • Insrale 10 unidad en un angulo de 30' a menos.
the same rating. ou moins. • 5i se funde elfusible, en primer lugar asegurese de que los cables no
• Connect the speaker wires correctly to the terminals to which • Si un fusible saute, assurez-vous d'abord que les cables n'ont hayan causado un cortaeireuiro, y luego reemplaee el fusible usado
they correspond. The unit may be damaged or fail to work if you pas cause de court-circuit puis remplacez Ie vieux fusible par un por otro del mismo regimen.
share the e wires or ground them to any metal part in the car. nouveau de meme valeur. • Coneere los cables de los alravaees a cada uno de los terminales
• When only two speakers are being connected to the system, • Connectez separement chaque cable d'enceinte a la borne correspandientes. La conexi6n compartida de los cables ea
connect the connectors either to both the front output terminals correspondante. L'appareil peut etre endommage si Ie cable 10 conexi6n a tierra de los mismos a cualquier parte metdlica
or to both the rear output terminals (do not mix front and rear). e
negatif pour une des enceintes ou Ie ccible de masse entre en del autom6vil padro danar la unidad 0 impedir su correcro
• Do not touch the metal part of this unit during and shortly after contact avec une partie metallique du vehicule. funcionamiento.
the use of the unit. Metal part such as the heat sink and enclosure • Quand deux haut-parleurs seulement sont connectes au systeme, • Cuando se han conectado solamente dos altavoces al sistema,
become hot. connectez les cables soit aux prises de sortie avant, soit aux prises conecte los conectores yo sea a ambos terminales de salida
• Mounting and wiring this product requires skills and experience. de sortie arnere (c.a.d. ne melangez pas I'avant et l'arriere). delanteros, 0 a ambos terminales de salida rraseros (0 sea, no mezde
For safely'S sake, leave this work to professionals. • Ne touchez pas la partie metallique de cet appareil pendant ou terminales delameros y rraseros).
If you experience problems during installation, consult your juste apres son utilisation. Les parties metalliques, comme Ie • No roque las partes meralicas de 10 un/dad durante 0 justa despues
Kenwood dealer. dissipateur de chaleur et Ie boitier, deviennent chaudes. de utilizar la unidad. Las partes metdlicas, tales como el radiador 0 10
• Le montage et Ie cablage de ce produit necessite des competences carcasa, pueden estar muy calientes.
et de I'experience. Pour des raison de securite, laissez ce travail a • La insralaci6n y cableado de este produero requiere de habilidad
des professionnels. yexperiencia. Por seguridad, deje que un profesional realice este
Si VOlls rencontrez des problemes pendant I'installation, trabojo.
consuhez votre revendeur Kenwood. Si tiene problemas durante la instalaci6n, comulte con su distribuidor
Kenwood.
Remove the key from the ignition switch, then disconnect the 1 Retirez la ele de contact, puis deconnectez la borne e de la 1 Quite 10 /love del interruptor de encendido; despues, desconeete
e terminal of the car battery. batterie de la voiture. el termlna/e de 10 bateria del autom6vil.
2 Make proper input and output wire connections. 2 Realisez une connexion correcte des fils d'entree et sortie. 2 Realice las conexiones de los cobles de entrada y salida
. . UWiring connection" . . "Connexions" correspondientes.
3 Install the unit to your car. 3 Installez I'appareil dans votre voiture. ... "Conexl6n del cableado"
... "Installing the unit" ... "Installation de l'appareil" 3 Instale 10 unldad en su autom6vil.
4 Reconnect the e terminal of the car battery. 4 Reconnectez 1a borne e
de la batterie de la voiture. ... Hlnstalaei6n de 10 unldad"
5 Reset the unit. 5 Reinitialisez l'apparei!. 4 Vuelva a conectar el termina/e de 10 bateda del autom6vil.
5 Reinicialice 10 unidad.
-
White / Blanc / Blanco
To front speaker (left) / A +)-"===="-"'==----
I'enceinte avant (gauche) / Blue / Bieu / Azul
AI alrovoz delantero }--'It-';;(M'''o'''t''-o'''ra"'n"'t"'en"-n"'a"'c-o-n"-tr-o"'lw.,-i.,-re"')"'/-----r.A"NTc;CO"'NT= (Not used) / (Non utilise) / (Sin utilizar)
(Izquierdo) (Cable de commande de l'antenne moteur) /
(Cabe de control de 10 antena motorizada) To the power control terminal when using the optional power amplifier, or
to the antenna control terminal in the vehicle.! A la borne de commande
+ Gra / Gris / Gris
.-:B::,lu",e,-lW=h"ite,-/,-B~I",eul=B",lan:""c"-/.:.:Az",u",I/""B",la::.n,,,co,,--
_ _==~ d'alimentation lorsque vous utilisez l'amplificateur de puissance en option, soit a
To front speaker (right) / A Gray/Black / (Power control wire) ! P. CaNT la borne de commande d'antenne du vehicule./ AI terminal de control de potencia,
I'enceinte avant (droHe) / AI Gris/Noirl (Fil de commande d'alimentation) / cuando utiliza el amplificador de potencia opcional, 0 al terminal de control de la
alrovoz delantero (derecho) GrisiNe ro (Coble de control de potencia) antena en el vehleulo.
To the terminal that is grounded when either the telephone rings or during
conversation. (fa connect the Kenwood navigation system, consult your
+ Green / Vert / Verde
Brown I Marron / Marr6n navigation manual.) I A la borne qui est mise ala masse lorsque Ie telephone
To rear speaker (left) / Vers Green/Black / ....--;'(M"u"'t"'e"c-'o"nt"'ro"'I"'w"'ir'-e"')/==--------,-"'M"'urr"";- sonne ou pendant les conversations. (Pour connecter au systeme de navigation
l'enceinte arriere (gauche) / Vert/Noir I (Cable de contr6le de la sourdine) / Kenwood, consultez Yotre manuel de navigation.) / AI terminal de tierra cuando
AI oltavoz trasero (IzqUierdo) ( : - }Verde/Negro
-_-'--"-' --J (Silenciar cable del control) suena el telefono 0 durante la conversaci6n. (Para coneetQr elsistema de navegaci6n
Kenwood, consulte el manual del sistema de navegaci6n.)
Car fuse box / Boite de fusible de la Ignition key switch /
voiture / Caja de fusibles del vehfculo Commutateur de ele de
contact / Interruptor de la flave
To rear speaker (right) / Vers de encendido
nition wire) / Rou e (Clble d'aI!uma e) / Ro'o (Cable de encendido)
I'enceinte arriere (droite) /
Car fuse box / Boite de
AI altavaz trasero (derecho)
r-...:..:::=..o:::::=:L..::=.:...L.:==============="---.. fusible de la voiture /
Black (Ground wire) / Noir (Fil de terre) / Ne ro (Cable a tierra) Caja de fuslbles del
To the metallic body or chassis of the car / vehfcu{o
Vers corps metallique ou chassis de la voiture /
Battery /
A un cuerpo metdlico 0 chasis del autom6vil Batterie /
8aterfa
"X t
T:
~[ smm EJ"[smm
sleeve firmly In place I Tordez les languettes Toyota cars /
, , .MAX. • , MAX.
appropriees pour maintenir Ie manchon de montage Voitures Toyota /
Gi-< :-; H Autom6viles Toyota
en place. / Doble las pestarias correspondientes para ~ 0Smm 0Smm
sostener el manguito de montaje firmemente en N:
posici6n. Nissan cars I
Voitures Nissan /
Autom6viles Nissan
Date d'achtat
Data da compra
Purchase date
Attention:
This card and receipt (or invoice) are necessary to purchase a new panel in case of theft
or damage.
Attention:
Vous aurez besoin de cette carte et du re<;u (ou de la facture) pour acheter un nouveau
panneau en cas de vol ou d'endommagement.
Aten~io:
Em caso de dano ou perda do painel frontal, este Certificado de Garantia e a Nota Fiscal
de compra serao requisitados para a aquisi<;ao de um novo paine!.
~ 846-0812-00/01 (K) (10/02)
Downloaded from www.Manualslib.com manuals search engine
U.S.A. KENWOOD USA CORPORATION
This warranty will be honored only in the U.S.A. WHO IS PROTECTED EXCLUSION OF DAMAGES
This warranty is enforceable only by the original purchaser. KENWOOD'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS
KENWOOD LIMITED WARRANTY LIMITED TO THE REPAIR OR REPLACEMENT OFTHE PRODUCT
FOR CAR STEREO COMPONENTS WHAT WE WILL PAY FOR AT OUR OPTION. KENWOOD SHALL NOT BE LIABLE FOR:
We will pay for all labor and material expenses for covered 11NSTALLATION OR REMOVAL CHARGES, DAMAGE
items. Payment of shipping charges is discussed in the next TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN
HOW LONG IS THE WARRANTY
section of this warranty. KENWOOD CAR STEREO COMPONENTS, DAMAGES
Kenwood U.S.A. Corporation ("Kenwood") warrants this
BASED UPON INCONVENIENCE, LOSS OF USE OF THE
product for aperiod of one (1) year from the date of original
HOW TO OBTAIN WARRANTY PRODUCT; OR
purchase.
2 ANY OTHER DAMAGES, WHETHER INCIDENTAL,
SERVICE CONSEQUENTIAL OR OTHERWISE.
WHAT IS COVERED AND WHAT IS If your KENWOOD product ever needs service: SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
NOT COVERED 1. Take or ship it to any KENWOOD Authorized Service Center LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT
Except as specified below, this warranty covers all defects in in Ihe U.S.A. along with & complete description of the. AllOW THE EXCLUSION OR LIMITATION OF INCIOENTAl OR
material and workmanship in Kenwood car stereo components. problem. (if you are uncertain as to whether aService Center CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS
The following are not covered by the warranty: is authorized, please call1-800-KENWOOD lor the nearest AND EXCLUSIONS MAY NOT APPLY TO YOU.
1 Any product which is not distributed in the U.S.A. by Service Center. 1-800-536-9663).
Kenwood or which is not purchased in the U.S.A. from an 2. Although you must pay any shipping charges it it is necessary This warranty gives you specific legal rights, and you may also
authorized Kenwood car stereo dealer or an automobile to ship the product for warranty service, wewill pay the return have other rights which vary from state to state.
dealer, unless the product is purchased through the U.S.A shipping charges if the repairs are covered by the warranty
Military Exchange Service. within the United States. If aproblem developsduring or after the Limited Warranty Period,
2. Any product on which the serial number has been defaced. 3. Whenever your units are taken or sent for warranty service, O! if you have any questions regarding the operation ot the
modified or removed. you must include acopy of the original dated sales receipt product, you should contact your KENWOOD Authorized Dealer
3. Damage, deterioration or malfunction resulting from: as proof 01 warranty coverage. or Authorized Service Center. If the problem or your question is
a. Any shipment of the product (claims must be presented not handled to your satisfaction, please contact our Customer
to the carrier). LIMITATION OF IMPLIED Relations Department at the address listed below:
b. Installation or removal of the product. WARRANTIES
c. Accident, acts of nature, misuse, abuse, neglect, ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES KENWOOD USA CORPORATION
unauthorized product modification or failure to follow OF MERCHANTABILITY AND FITNESS FOR APARTICULAR
instructions supplied with the product. P.O Box 22745,2201 East Dominguez
PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF
d. Repair or attempted repair by anyone not authorized THIS WARRANTY Street, Long Beach, CA 90801-5745
by Kenwood. Tel: (310) 639-5300
e. Any other cause which does not relate to a product
defect.
GARANTIE KENWOOD (e) les defauts causes par les desaslres, les accidents, les L'ENTIERE GARANTIE
KENWOOD ELECTRONICS CANADA INC. (ci-apres appelee abus, lesemplois incorrects, les eclairs, les surtensions de Cette garantie represente I'entjere garantie donnee par ecrit par
"KENWOOD"), donne par ecrit la garantie suivante aI'acheteur courant, les manques de soins ou d'entretiens periodiques, KENWOOD. KENWOOD ne se tient aucunement responsable
original de chaque nouveau produil Kenwood distribue au les modifications non autoriseesou les manques de respect de toutes extensions ni de toutes augmentations de celie
Canada par KENWOOD et achete aun concessionnaire autorise du mode d'emploi: garantie laites ou entreprises par toules personnes, parties,
par KENWOOD. (I) les defauts ou les dommages causes lors de reparations concessionnaires ou centres de service ou par leurs agents
eflectuees par une personne ou par une partie non autorisee ou employes au nom de KENWOOD au moyen d'aflirmations
KENWOOD garantit, sous reserve des termes et des conditions par KENWOOD; verbales ou ecrites, d'annonces ou de promotions, yinclus tous
enonces ci-dessous, que chaque nouveau produit Kenwood, (g) les defautscauses par I'emploi de pieces ou de dispositifs qui prog rammes ou plans de garantie etendue que puissent oflrir
dans des conditions d'emploi normales, est exempt de tous ne se conforment pas aux exigences de KENWOOD; les concessionnaires au les centres de service, amoins que
defauts. Si I'un defaut se produit pendant la periode de garantie, (h) les finitions exterieures, les pieces cosmetiques, les tetes KENWOOD n'y ait consenti par Bcrit d'avance.
KENWOOD s'engage aassumer Ie coOt des pieces defectueuses de bandes, les adaptateurs, les antennes, les cables,
et de la main-d'oeuvre necessaires pour effectuer les reparations les bandes, les disques endommages ou deperis, ni les RENONCIATION
pourvu que de tels defauts sont allribuables a des pieces defauts ou dommages causes par des piles defectueuses KENWOOD renonce atoutes responsabilites de perte de temps,
detectueuses employees lors de la fabrication du produit ou qui fuient; d'emploi du produit, detous dommagesindirects ou accessoires
Kenwood ou ala main-d'oeuvre tel qu'etabli par KENWOOD ou (i) les detauts ou dommages qui se produisent pendant causes ad'autres produits ou biens, de taus inconvenients ou
par I'un de ses centres de service autorises. Appelez KENWOOD I'expedition des produits Kenwood (On devrait deposer de de toutes pertes commerciales.
pour verifier si un concessionnaire ou un centre de service est telles reclamations aupres des compagnies de transport);
autorise par KENWOOD. (j) les conversions de tension eVou de frequence du
produil;
AVIS AUX CONSOMMATEURS
Les stipulations contenues dans la presente garanlieecrite n'ont
PERIODE DE GARANTIE (k) les trais d'installation ou d'enlevement du produit.
pas pour but de limiter, de modifier, de diminuer, de rejeter ni
Les pieces et la main-d'oeuvre necessaires pour la reparation d'exclure d'autres garanties ni droits enonces dans n'importe
des produits Kenwood sont garanties pendant la perioded'un (1) COMMENT OBTENIR DU SERVICE quelles lois ou legislations provinciales ou federales.
an acompter de ladate d'achat, de bail ou de location originale, SOUS GARANTIE
sauf dans les cas ou les produits Kenwood sont employes dans Au cas ou un service sous garantie de votre produit Kenwood
un but professionnel ou commercial, ou la garantie des pieces IMPORTANT
s'avere necessaire, veuillez livrer Ie produit an'importe quel KENWOOD ne considere pas cetle garantie loute seute comme
et de la main-d'oeuvre demeure en vigueur pendant une peri ode centre de service KENWOOD et presenter la copie originale du
de quatre-vingt-dix (90) jours sous reserve des fermes et des etant une preuve d'achat valide. Lorsqu'on demande du service
contrat de vente et celie carte de garantie en tant que preuve sousgarantie, il faudrapresenler lacopie originaledu contrat de
conditions de la garantie. de garantie ou veuillez faire parvenir votre produit assure et vente aussi bien que cetle carte de garantie en tant que preuve
port paye au centre de service KENWOOD autorise Ie plus de garantie. On recommande de les conserver dans un lieu sOr
EXCLUSIONS DE GARANTIE proche. Pour eviter toutes possibilites de dommages pendant au cas ou elles s'avereraient necesaires aI'avenir.
Celie garantie ne couvre pas: Ie transport, veuillez bien emballer Ie produil. Veuillez inclure
(a) les produits achetes aI'etranger ou achetes au Canada et une copie du contrat de vente original et celie carte de garantie
transportes aI'etranger; en tant que preuve de garantie aussi bien que volre nom,
KENWOOD ELECTRONICS CANADA INC.
(b) les produits achetes aun concessionnaire non autorise numeros de telephone au poste de travail eVou au domicile, 6070 Kestrel Road, Mississauga,
par KENWOOD; votre adresse et une description detaillee des defauts. Les Ontario, Canada L5T 1S8
(c) les produils dont Ie numero de serie manque, aete eflace produits sous garantie repares seront retoumes port paye aux Telephone: (905) 670-7211
ou modifie; destinations a I'interieur du Canada. Le consomma1eur sera
(d) les services d'entretien periodiques qui n'indiquent aucun Telecopieur: (905) 670-7248
responsable de tous frais de transport et d'autres frais qui s'y
detaut couvert par celte garantie; rapportent pour faire expedier les produits a destinations a
Downloaded from www.Manualslib.com manuals search engine
I'exterieur du Canada.
MILITARY
Units purchased through the U.SA. military exchange service LIMITATION OF IMPLIED KOREA:
overseas may be serviced under warranty in the continental WARRANTIES Kenwood Rep,; c/o
U.S.A., subject to the following conditions. Any and all implied warranties, including warranties of KOAX Repair Shop, AAFES-PAC
1) The original warranty is in effect. merchantability and fitness for aparticular purpose, shall be
2) Proof of purchase is provided to the servicer. DD-Camp Market, APO San Francisco
limited in duration to the length of this warranty. 96488
WARRANTY FOR MILITARY MARKET EXCLUSION OF CERTAIN DAMAGES
Kenwood corporation is proud of the Quality and workmanship KENWOOD's liability for any defeelive product is limited to GUAM:
of its audio equipment. This unit has been properly designed, the repair or replacement of said product, at our polion, and Kenwood Rep,; c/o
tested and inspected before it was shipped to you. II properly shall not include damages of any kind, whether incidental, Guam NEX No. 230-010,
installed and operated inaccordance with instructions furnished, consequential or otherwise, expect to the ex1ent prohibited
it should give you an optimum reliable pertormance. FPO San Francisco 96630
by applicable law. Kenwood Rep,; c/o
WARRANTY PERIOD GUAX, AAFES-PAC, APO San Francisco
This product is warranted for aperi ad of (1) year from the date KENWOOD AUTHORIZED SERVICE 96334
of the original purchase. CENTERS IN MILITARY MARKET
U.S.A.:
SCOPE OF WARRANTY JAPAN: Hawaii
Except as specified below, this warranty covers all defects in Yokota
materials and workmanship of the Kenwood brand products, Kenwood Factory Service
Kenwood Rep,; c/o 99-994 Iwaena St., Aiea, Hawaii 96701
During the warranty period, any authorized Kenwood Service Yokota BX, JAAX AAFES-PAC,
Center in the military market listed in the back of this warranty APO San Francisco 96328 Alaska
card will provide you free-of-charge both parts and labor
Vista Radio TV,;
required to correct any defect in materials or workmanship.
Zama 861 East Loop Road, Anchorage, Alaska
The following are not covered by this warranty, Kenwood Rep,; c/o 99501
1. Voltage conversions. Zama PX, JAAX AAFE5-PAC, Anchorage Commercial Electronics, Inc.;
2. Periodiccheck-ups which do not discloseany defectcovered APO San Francisco 96343 1450 East 9th Ave., Anchorage, Alaska
by the warranty. 99501
3. Cabinets, grilles, other ex1erior finishes, bells, tape heads,
and other non-durable parts and accessories. Misawa
4. Units onwhich the serial number has been effaced, modified Kenwood Rep,; c/o In The Continental U.S.A.
or removed. Misawa BX, JAAX AAFES-PAC, For Nearest Authorized Service Center;
5. Installation and/or removal charges, APO San Francisco 96519 Tel: 1-800-536-9663
6. Damaged magnetic tapes.
7. House call charges for any repa irs,
8. Shipping or delivery charges to or from an authorized Yokosuka Kenwood Service U.S.A.
Kenwood Service Center, Kenwood Rep,; c/o Kenwood Factory Service;
9. Thiswarrantywill not cover any failure that is due to any of the A-33, Yokosuka NEX No. 260-010 P.O. Box 22745,2201 East Dominguez
following conditions in accordancewilh the visual inspection FPO Seattle 98760 Street,
of the authorized Kenwood Service Center: Long Beach, California 90801-5745
'Improper maintenance or repair, including the installalion of Tel: (310) 639-5300
parts or accessories that do not conform to the Quality and Atsugi
specifications of the original parts. Kenwood Rep,; c/o
, Misuse, abuse, neglect, unauthorized product modification Atsugi NEX No. 260-020 FPO Seattle EUROPE:
or failure to follow instructions contained in the Owner's 98767 Please inquire at the military resale
Manual. outlets where you bought your Kenwood
, Accidental or intentional damages. products, or
'Repairs or attempted repairs by an unauthorized agency. Iwakuni
(All repairs must be pertormed at an authorized Kenwood Kenwood Rep,; c/o KENWOOD ELECTRONICS
Service Center.) Marine Corps Exchange, Marine Corps DEUTSCHLAND GMBH:
'Damages or deteriorations caused during shipment (Claims Air Station, Rembrucker-Str. 15, 63150 Heusenstamm,
must be presented to the carrier). FPO Seattle 98764 Germany
'Damages or deteriorations resulting from removal and/ Tel.: 49-06104-69010
or replacement.
Sasebo
PURCHASER'S RESPONSIBILITIES Sasebo NEX;
As the purchased of anew Kenwood brand product, you are Navy Exchange 26Q-040
requested to do the following in order to obtain Kenwood F.A. Box 115 FPO Seattle 98766
warranty service.
1. Retain your sales sliporotherevidence ofpurchasefor proving
your eligibility for requesting Kenwood warranty service. Okinawa
2. Make your unit available to an authorized Kenwood Service Kenwood Rep,; c/o
Center in the military market for inspection and approved OWAX, AAFES-PAC, APO San Francisco
warranty service, or ship your unit in its original carton box 96230
or equivalent, fully insured and shipping charges prepaid,
to the authorized Kenwood Serv ice Center.
Dear Customer,
Thank you for purchasing this kenwood product. As mentioned in the pages of this booklet, our warranty is only
valid in the countries listed. If your country is not listed please contact your retailer for information on warranty
procedure, or write to: