KENWOOD
KENWOOD
KENWOOD
KDC-U4549SD
KDC-U4549
CD-RECEIVER
INSTRUCTION MANUAL
2 English
Important to know...
■ To prevent a short circuit, never put or leave
any metallic objects (such as coins or metal
tools) inside the unit.
■ Caution: Adjust the volume so that you can
Maintenance
Cleaning the unit: Wipe off the dirt on the
panel with a dry silicon or soft cloth. Failure
to observe this precaution may result in The marking of products using
damage to the monitor or unit. lasers
Cleaning the connector: Wipe off dirt on
the connector of the unit and faceplate. Use CLASS 1
a cotton swab or cloth.
LASER PRODUCT
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1.
It means that the unit is utilizing laser
beams that are of a weaker class. There is
no danger of hazardous radiation outside
the unit.
English 3
2 Insulation sheet
2
detached. 2 4
■ The faceplate is a precision piece of
4 English
KDC-U4549SD
KDC-U4549
6 English
Selects the available sources (TUNER, USB or iPod, SD, CD, AUX,
SRC STANDBY), if the power is turned on.
SRC • If the source is ready, playback also starts. “iPod”, “SD” and “CD” are
selectable only when an iPod is connected, an SD card is inserted or a
disc is loaded.
Volume knob VOLud Adjusts the volume level.
(turn) 5 / ∞ Selects items.
Volume knob ENT 38 Confirms selection.
(press) — Enters [FUNCTION] settings.
■ Selects the FM bands (FM1/ FM2/ FM3) or AM.
*AM– / ■
BAND Selects the next folder. (Press *AM– on remote controller to select
#FM+
the previous folder.)
6 (38) ENT 38 Pauses/resumes playback of a disc/ USB device/ SD/ iPod.
■ Searches for radio station.
4/
4/¢ ■ Selects track/file.
+¢ ■
Fast-forwards/reverses tracks/files if pressed and held.
■ Changes the display information.
— ■ Enters Bluetooth easy pairing mode if pressed and held. (page 22)
KDC-U4549SD only:
SD —
Selects “SD” source.
KDC-U4549 only:
■ Selects “iPod” source.
iPod — ■ Switches the controlling terminal (HANDS ON/ HANDS OFF) for
English 7
■ To continue listen to the audio system during a call, press SRC. “CALL” disappear and the
audio system resumes.
When a call ends, “CALL” disappear.
■ The audio system resumes.
Getting Started
Canceling the display Adjusting the clock
demonstration 1 Press the volume knob to enter
The display demonstration is always turned [FUNCTION] mode.
on unless you cancel it. 2 Turn the volume knob to select
[SETTINGS], then press to enter.
When you turn on the power (or after you 3 Turn the volume knob to select [CLOCK],
reset the unit), the display shows: then press to enter.
[CANCEL DEMO] \ [PRESS] \ [VOLUME 4 Turn the volume knob to select [CLOCK
KNOB] ADJUST], then press to enter.
1 Press the volume knob. Clock hour flashes on the display.
[YES] is selected as the initial setup. 5 Turn the volume knob to adjust the hour,
2 Press the volume knob again to confirm. then press to enter minute adjustment.
[DEMO OFF] appears. Clock minutes flashes on the display.
■ If no operation is done for about 15 seconds 6 Turn the volume knob to adjust the
or if you turn the volume knob to select minute, then press to confirm.
[NO] in step 2, [DEMO MODE] appears and Press 4 / ¢ to move between the
the display demonstration starts. hour and minute adjustment.
7 Hold to finish the procedure.
Setting the demonstration mode
1 Press the volume knob to enter
[FUNCTION].
2 Turn the volume knob to select [DEMO
MODE], then press to enter.
3 Turn the volume knob to select [ON] or
[OFF].
If [ON] is selected, display demonstration
starts if no operation is done for about 20
seconds.
4 Hold to finish the procedure.
8 English
English 9
■ Press and hold for about 2 seconds to memorize the current station.
■ Press briefly to recall memorized station.
10 English
English 11
12 English
2 Press the number buttons to enter the a different iPod, “NO INFO” followed by
track number. “MPLIST DELETE” appears.
3 Press 4 / +¢ to search for the music. To delete the playlist, turn the volume knob
■ To cancel the Direct Music Search mode, to select “YES”, then press to confirm.
press . ■ You can also register the song displayed in
14 English
English 15
■ When removing discs from this unit, pull USB hub and Multi Card Reader.
them out horizontally. ■ Make sure all important data has been
■ Remove the rims from the center hole backed up to avoid losing the data.
and disc edge before inserting a disc. ■ Connecting a cable whose total length
phones, you need to select one of them. ■ To return to the Phone Book mode, press
hold .
■ To exit Bluetooth mode, press SRC.
■ To move to the next digit, press ¢. message is displayed. Pressing the Volume
■ To delete the last digit, press 4. knob allows you to retry voice input. Refer
■ Press number button (1 – 0), #(FM+), to <Troubleshooting> (page 34).
*(AM–), or +(¢) on the remote ■ Both the name and category require
20 English
English 21
22 English
English 23
deselected. registration.
■ If a cell-phone is already selected,
deselect it, and then select a different Registering Phone Book Name Type
one. 1 KDC-U549BT
7 Hold to finish the procedure. Press to enter Bluetooth mode.
■ To exit Bluetooth mode, press SRC. KDC-U4549SD / KDC-U4549
Press and hold the volume knob to enter
Setting a Voice Command Bluetooth mode.
Registering Phone Book Name 2 Turn the volume knob to select
1 KDC-U549BT [SETTINGS], then press to enter.
Press to enter Bluetooth mode. 3 Turn the volume knob to select [VOICE
KDC-U4549SD / KDC-U4549 TAG], then press to enter.
Press and hold the volume knob to enter 4 Turn the volume knob to select [PN TYPE
Bluetooth mode. EDIT], then press to enter.
2 Turn the volume knob to select 5 Turn the volume knob to select
[SETTINGS], then press to enter. [GENERAL], [HOME], [OFFICE], [MOBILE],
3 Turn the volume knob to select [VOICE or [OTHER], then press to enter.
TAG], then press to enter. 6 Turn the volume knob to select [PN TYPE
4 Turn the volume knob to select [PB REG], then press to enter.
NAME EDIT], then press to enter. ■ To select “PN TYPE CHK”, play the
to 5 in <Calling a Number in the Phone tag. Turn the volume knob to select “YES”,
Book> (page 19).
24 English
26 English
asterisk (*).
English 27
[AUDIO CONTROL] : While listening to any source except in STANDBY state or Bluetooth mode.
Item Selectable setting (Preset: *)
SUB-W LEVEL –15 — 0 * — +15: Adjusts the subwoofer output level.
BASS BOOST B.BOOST LV1 */ B.BOOST LV2: Selects your preferred bass boost level. ; OFF: Cancels.
SYSTEM Q NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME: Selects a preset sound mode suitable to the
music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)
BASS ADJUST
BASS CTR FRQ 40/ 50/ 60/ 70/ 80/ 100 */ 120/ 150: Selects the center frequency.
BASS LEVEL –8 — 0 * — +8: Adjusts the level.
BASS Q FACTOR 1.00 */ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXTEND ON: Turns on the extended bass. ; OFF *: Cancels.
MID ADJUST
MID CTR FRQ 0.5K/ 1.0K/ 1.5K/ 2.0K *: Selects the center frequency.
MID LEVEL –8 — 0 * — +8: Adjusts the level.
MID Q FACTOR 1.00 */ 2.00: Adjusts the quality factor.
TRE ADJUST
TRE CTR FRQ 10.0K/ 12.5K */ 15.0K/ 17.5K: Selects the center frequency.
TRE LEVEL –8 — 0 * — +8: Adjusts the level.
BALANCE L15 — 0 * — R15: Adjusts the left and right speaker output balance.
FADER R15 — 0 * — F15: Adjusts the rear and front speaker output balance.
SUBWOOFER SET ON *: Turns on the subwoofer output. ; OFF: Cancels.
DETAILED SET
HPF FRONT THROUGH *: All signals are sent to the front speaker. ; 40/60/80/100/ 120/150/180/220 (HZ): Frequencies
lower than the specified value are cut off.
HPF REAR THROUGH *: All signals are sent to the rear speaker. ; 40/60/80/100/ 120/150/180/220 (HZ): Frequencies
lower than the specified value are cut off.
LPF THROUGH *: All signals are sent to the subwoofer. ; 50/60/80/100/120 (HZ): Frequencies higher than the
SUBWOOFER specified value are cut off.
SUB-W PHASE REVERSE (180°)/ NORMAL (0°) *: Selects the phase angle of the subwoofer output to be in line with the
speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for
[LPF SUBWOOFER].)
28 English
[SETTINGS]
Item Selectable setting (Preset: *)
AUX NAME SET AUX */ TV/ VIDEO/ GAME/ PORTABLE/ DVD: Selects the desired name for the connected component.
(Selectable only if “AUX” is selected as the source.)
CLOCK
CLOCK ADJUST (For details, see page 8.)
DISPLAY
DIMMER SET ON: Dims the display illumination. ; OFF *: Cancels.
TEXT SCROLL AUTO */ ONCE: Selects to scroll the display information automatically, or scroll only once. ; OFF: Cancels.
BT DVC STATUS You can display the connection status, signal strength, and battery level of cell-phone.
HF-CON: Connection status for cell-phone. ; AD-CON: Connection status for BT Audio. ; BATT: Battery level of
cell-phone. ; SIGNAL: Signal strength of cell-phone.
English 29
\ <Wiring connection> (page 32) vehicle. Make sure the faceplate will not hit
3 Install the unit to your car. the lid of the console (if any) when closing
\ <Installing the unit> (page 33) and opening.
4 Reconnect the · terminal of the car ■ After the unit is installed, check whether the
30 English
BT200 as follows:
1: OFF, 2: OFF, 3: OFF
¤ CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
English 31
FM/AM antenna
USB connector input (JASO)
Antenna Cord
AUX input (Stereo)
Use the mini-plug (3.5 mm ø) cable KDC-U4549SD/ KDC-U4549
which is stereo type and does not have Rear output
R L
any resistance. Front output
Sub Woofer output
KDC-U549BT
R L
Front output
Fuse (10A)
Rear output/ Sub Woofer
output switchable
Wiring harness D (page 9)
White
To front left speaker
White/Black To Kenwood disc changer/ External
Gray optional accessory (KDC-U4549SD/
To front right speaker
Gray/Black KDC-U4549 only)
Green (To connect these leads, refer to the
To rear left speaker relevant instruction manuals.)
Green/Black
Purple
To rear right speaker
Purple/Black
If no connections are made, do not let the wire come out from the tab.
Blue Depending on what antenna you are using, connect
ANT. CONT either to the control terminal of the motor antenna, or
(Antenna control wire)
to the power terminal for the booster amplifier of the
film-type or short pole type antenna.
Blue/White
(Power control wire) P.CONT When using the optional power amplifier, connect to
its power control terminal.
Brown To connect the Kenwood navigation system, consult
(Mute control wire) MUTE your navigation manual.
(Connect to the terminal that is grounded when
either the telephone rings or during conversation.
KDC-U4549SD/ KDC-U4549 only)
Light Blue/Yellow
To use the steering wheel remote control feature, you
(Steering remote control REMOTE CONT
STEERING WHEEL
need to an exclusive remote adapter (not supplied)
wire ) REMOTE INPUT matches your car is required.
Car fuse box Ignition key switch
Red (Ignition wire) ACC
Yellow (Battery wire) Car fuse box
(Main fuse)
Black (Ground wire)
To the metallic body or chassis of the car +
– Battery
32 English
1
3 Connect the wiring harness to the
unit. Other wiring connection has
C been completed earlier. (page 32)
2
1
B
A D
2
2 Before attaching, make
sure the direction of the 1
escutcheon is correct.
(Wider hooks on the 3 Dashboard of
bottom side.) your car
C
4
Bend the appropriate tabs
5 to hold the mounting sleeve
B firmly in place.
A
■ SD card is not inserted properly. Insert an SD card, and change the source to SD again.
“NO MUSIC” or “ERROR 15” appears. The connected USB device or inserted SD card contains no playable audio file. / Media was
played that does not have data recorded that the unit can play.
“NA DEVICE” appears. ■ Connect a supported USB device, and check the connections.
“USB ERROR” appears. Remove the USB device, turn the unit off, then turn it on again. If the unit still showing the
same display, try to connect another USB device.
“iPod ERROR” appears. Reconnect the iPod. / Confirm that the software for the iPod is the latest version. / Reset
the iPod.
Noise is generated. Skip to another track or change the disc.
Tracks cannot play back as you have Playback order is determined when files are recorded.
intended them to play.
“READING” keeps flashing. Longer readout time is required. Do not use too many hierarchies and folders.
Elapsed playing time is not correct. This is caused by how the tracks are recorded.
The number of songs contained Podcast files are not counted in this unit as this unit does not support the playback of
in “SONGS” category of this unit podcast files.
is different from that contained in
“SONGS” category of iPod.
34 English
Bluetooth
Symptom Remedy/Cause
The hands-free talk volume is low. The hands-free talk volume can be adjusted independently. Adjust it during hands-free talk.
[MIC GAIN], [NR LEVEL] and [EC LEVEL] of <Bluetooth Setup> (page 25).
No beep is heard at reception of No beep is heard depending on the type of your cell-phone. The [CALL BEEP] of <Bluetooth
an incoming call. Setup> (page 25) is set ON.
Voice is not recognized. ■ The vehicle window is open. If the surrounding noise is large, voice cannot be recognized
audio player is discontinuous. Bluetooth device. Move another Bluetooth device away from this unit.
■ Another Bluetooth device or profile is used for communication. The downloading of the Phone
English 35
36 English