ROLAND User Manual PNC 1410
ROLAND User Manual PNC 1410
ROLAND User Manual PNC 1410
PNC-1410
PNC-1210
USER'S MANUAL
* This User's Manual is intended for the PNC-1860, PNC-1410, as well as PNC-1210.
For the USA
FEDERAL COMMUNICATIONS COMMISSION NOTICE
Grounding Instructions
RADIO FREQUENCY INTERFERENCE
STATEMENT Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the Check with qualified electrician or service personnel if the
FCC Rules. grounding instructions are not completely understood, or if in
These limits are designed to provide reasonable protection doubt as to whether the tool is properly grounded.
against harmful interference in a residential installation.
Use only 3-wire extension cords that have 3-prong
This equipment generates, uses, and can radiate radio
grounding plugs and 3-pole receptacles that accept the tool’s
frequency energy and, if not installed and used in accordance
plug.
with the instructions, may cause harmful interference to radio
communications. Repair or replace damaged or worn out cord immediately.
However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the Operating Instructions
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: KEEP WORK AREA CLEAN. Cluttered areas and benches
- Reorient or relocate the receiving antenna. invites accidents.
- Increase the separation between the equipment and DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
receiver. use power tools in damp or wet locations, or expose them to
- Connect the equipment into an outlet on a circuit different rain. Keep work area well lighted.
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician DISCONNECT TOOLS before servicing; when changing
for help. accessories, such as blades, bits, cutters, and like.
For Canada
CLASS B NOTICE
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
CLASSE B AVIS
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
ROLAND DG CORPORATION
1-6-4 Shinmiyakoda, Hamamatsu-shi, Shizuoka-ken, JAPAN 431-2103
MODEL NAME : See the MODEL given on the rating plate.
RELEVANT DIRECTIVE : EC MACHINERY DIRECTIVE (89/392/EEC)
EC LOW VOLTAGE DIRECTIVE (73/23/EEC)
EC ELECTROMAGNETIC COMPATIBILITY DIRECTIVE (89/336/EEC)
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Thank you very much for purchasing the CAMM-1 PNC-1860/1410/1210.
• To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through this
manual completely and store it in a safe location.
• Unauthorized copying or transferal, in whole or in part, of this manual is prohibited.
• The contents of this operation manual and the specifications of this product are subject to change without notice.
• The operation manual and the product have been prepared and tested as much as possible. If you find any misprint or error,
please inform us.
CONTENTS
Typographic Conventions ....................................................................................................................................... i
To Ensure Safe Use ............................................................................................................................ ii
About the Labels Affixed to the Unit ................................................................................ iii
To Ensure Correct Use .............................................................................................................................................. iv
1 CHECKING ACCESSORIES ............................................................................................................................. 1
2 PART NAMES AND FUNCTIONS ..................................................................................................................... 1
2-1 Front View .............................................................................................................................................. 1
2-2 Rear View ............................................................................................................................................... 1
2-3 Operation Panel ..................................................................................................................................... 2
3 BASIC OPERATION .......................................................................................................................................... 3
3-1 Setting Up and Connection .................................................................................................................... 3
3-2 Installing the Cutter ................................................................................................................................ 4
3-3 Loading the Material ............................................................................................................................... 5
Loading Roll Material .............................................................................................................................. 6
Loading Flat Material (Standard-size Material, Cut Material, Etc.) ......................................................... 8
To Perform Long Cutting ...................................................................................................................... 10
3-4 Selecting the Interface .......................................................................................................................... 11
3-5 Cutting Test - Setting Cutting Speed, Blade Force, and Blade Compensation .................................... 12
3-6 Downloading Cutting Data .................................................................................................................... 13
3-7 Applying the Completed Cutout ............................................................................................................ 15
3-8 When Completed Cutting ..................................................................................................................... 15
4 CARE AND MAINTENANCE ........................................................................................................................... 16
5 ABOUT THE CUTTING AREA ........................................................................................................................ 17
6 USING THE DISPLAY MENUS ....................................................................................................................... 17
7 DISPLAY MENUS FLOWCHART .................................................................................................................... 18
8 DISPLAY MENU LISTS ................................................................................................................................... 20
9 BLADES AND MATERIALS ............................................................................................................................. 24
10 PLOTTING ON PAPER MEDIA ....................................................................................................................... 25
11 WHAT TO DO IF .............................................................................................................................................. 26
12 SUPPORTED INSTRUCTION SETS .............................................................................................................. 29
13 CHARACTER SET .......................................................................................................................................... 30
SPECIFICATIONS ..................................................................................................................................................... 31
Typographic Conventions
This manual uses certain typographic symbols, outlined below.
This indicates a point requiring particular care to ensure safe use of the product.
Windows is registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
i
To Ensure Safe Use
Never disassemble or modify Handle the power cord with care. When pulling the power cord
this product. from an electrical socket, be
Do not step on or damage the power sure to grip the plug.
cord, or allow heavy objects to be
placed atop it. Failure to heed this may
result in
electrocution
or fire.
Do not allow liquids, metal Install in a level and stable location. Handle the blade with care.
objects or flammables inside the
machine. The unit may tip over otherwise.
Fire or
breakdown
may result.
Release the caster locks for the Unpacking, installation, and Do not place hands within the
stand before attempting to move. moving must be carried out by space to the front or rear of the
two or more persons. unit while in operation.
Use care to avoid pinching the Use the joining screws to secure
fingers when placing the unit on the unit to the stand.
the stand.
The unit may
tip over
otherwise.
ii
About the Labels Affixed to the Unit
These labels are affixed to the body of this product. The following figure describes the location and content of
these messages.
Rating label
iii
To Ensure Correct Use
This product is a precision instrument Do not install in an area subject to dust, Do not connect to an AC outlet that
and must be handled with care. high humidity or poor ventilation. supplies other than the specified voltage.
When the unit is not in use for an Arrange the power cord and interface
extended period, detach the electrical connection cable to prevent tripping
plug from the AC outlet. when moving around the unit.
iv
MEMO
v
1 CHECKING ACCESSORIES
Check the following to make sure that you received all the items that were shipped along with the unit.
Tool Carriage
The tool carriage is where the cutter (or pen)
is mounted. The tool carriage performs the
cutting by moving the tool left/right or up/
down.
Operation Panel
Power Switch
Grit Roller ON when switched to [ ], OFF when
Grasps and moves the material (or switched to [ ] .
paper) during cutting (or plotting).
Guide line
Cutter Protector
When loading a flat material, align the
Sheet sensor
right-hand edge of the material with this
When a material is passed through this
Platen guide line and load the material so that it is
portion, this sensor detects the material's
perfectly straight.
cutting range.
1
2-2 Rear View
Sheet Sensor
When a material is passed through this
portion, this sensor detects the material's
cutting range.
Sheet Loading Lever
When loading media, lift this lever to lower to
pinch rollers. To removing media, lower this
lever to raise the pinch roller.
Cursor Keys
Power LED
Used to move the blinking cursor. The
This lights up when the power is
and keys are also used to
switched on.
move the material, and the and
keys are used to move the tool
SETUP LED carriage.
This lights up when the SETUP key is
pressed to pause the PNC-1860/1410/
1210. TEST Key TEST
Pressed to execute a cutting test (Use
SETUP Key SETUP to confirm material specifications as
Pressing this key after loading a material causes the well as cutting speed, blade force, and
material's cutting range to be determined automatically. blade compensation).
2
* In this manual, sections that explain
commons points for the PNC-1860/
3 BASIC OPERATION 1410/1210 use only illustrations of the
PNC-1860. Some details of the PNC-
1410/1210 differ from the figure.
Never install this unit in any of the following situations, as it could result in damage:
Places where the installation surface is unstable or not level.
Places with excessive electrical noise.
Places with excessive humidity or dust.
Places with poor ventilation, because the PNC-1860/1410/1210 generates considerable heat during operation.
Places with excessive vibration.
Places exposed to strong illumination or direct sunlight.
For an explanation of how to assemble the unit and the stand (PNS-186/141/
130), refer to the “ASSEMBLY INSTRUCTIONS” included with the stand.
When using the unit while mounted on a stand, be sure to ensure a sufficient
amount of installation space for the unit. The required installation spaces for
each model are listed below.
PNC-1860 : 1200 mm (47-1/4") high, 1700 mm (66-15/16") wide,
and 750 mm (29-1/2") depth
PNC-1410 : 1200 mm (47-1/4") high, 1350 mm (53-1/8") wide, 600 mm
and 750 mm (29-1/2") depth (23-5/8")
PNC-1210 : 1200 mm (47-1/4") high, 1050 mm (41-5/16") wide,
and 750 mm (29-1/2") depth
The material moves while cutting is in progress. Objects which may obstruct
material movement must not be placed within 60 cm (23-5/8") to the front or
rear of the unit. 600 mm
(23-5/8")
Connection
• Always make sure that the power is off on both the computer and the PNC-1860/1410/1210 whenever any cables are connected
or disconnected.
• Securely connect the power cord, computer I/O cable and so on so that they will not be unplugged and cause failure during
operation.
• Cables are available separately. One which you are sure matches the model of computer being used should be selected.
Serial connector
Parallel connector
Serial connector
Power cord
3
3-2 Installing the Cutter
Always make sure the power switch is OFF before installing (or replacing) the cutter.
Do not touch the tip of the blade with your fingers, as the cutting performance of the blade will be impaired.
Installation
(1) Insert a blade into the blade holder until it snaps into place Push-pin
with an audible click.
* Take care not to break or
Blade holder chip the blade.
Blade
As shown in the figure below, support the tool setscrew from below and install the blade holder. Cutting quality may become
poor if installed without supporting the screw in this way.
(2) Loosen the tool securing screw on the tool carriage. Support the tool Blade holder
securing screw from below and install the blade holder. Insert the Tool carriage
blade holder until the collar is flush with the carriage. Tighten the
tool securing screw until the blade holder is secured in place. Loosen Tighten
Tool securing
screw
Removal
After detaching the blade holder from the tool carriage, do not tighten the tool setscrew. Leave this screw loose.
Tightening the screw makes the hole for inserting the holder to progressively smaller, which on turn makes it difficult to install
the blade holder.
(1) Loosen the tool securing screw on the tool carriage, (1) Blade holder (2)
then remove the blade holder from the tool carriage.
Tool carriage
(2) Press the push-pin and remove the blade from the blade Push-pin
holder. Loosen
Blade
Blade holder
Tool securing screw
4
3-3 Loading the Material
Below are shown the allowable widths (horizontal dimension) of materials that can be loaded and the maximum widths that can be
cut.
Acceptable material widths Maximum cutting area
PNC-1860 : 90—1372 mm (3-1/2"—54" ) PNC-1860 : 1195 mm (W) x 24998 mm (L) (47" x 984-1/8")
PNC-1410 : 90—1067 mm (3-1/2"—42" ) PNC-1410 : 889 mm (W) x 24998 mm (L) (35" x 984-1/8")
PNC-1210 : 50—762 mm (1-15/16"—30" ) PNC-1210 : 585 (W) mm x 24998 mm (L) (23" x 984-1/8")
There is no particular restriction on material length (vertical dimension). This means that you can use either flat materials such as
standard-size materials (ANSI, ISO, etc.) and cut materials, or roll materials. The grit rollers (pinch rollers that secure the material)
vary from one model to another, and settable ranges are determined for the left and right movable pinch rollers. Setting a pinch roller
outside the allowed range causes an error message to appear.
• The middle pinch roller is used as an auxiliary roller. Be sure to use the left and right pinch rollers to secure the
material in place.
• When loading a material, make sure that it passes over the material sensor above the platen. The size of the material
cannot be determined unless the material passes over the sheet sensor.
(1*) Position of the pinch roller (middle) when using material with a width of 30" :Grit Roller : Movable Pinch
(2*) Position of the pinch roller (middle) when using material with a width of 36" or 42" Roller (Middle)
(3*) Position of the pinch roller (middle) when using material with a width of 48" or 54"
:Movable Pinch : Movable Pinch
Roller (Left) Roller (Right)
6"
(approx. 152 mm)
12" (approx. 305 mm)
Material 18"
(approx. 457 mm)
24"
(approx. 610 mm)
30"
(approx. 762 mm)
36"
(approx. 914 mm)
42"
(approx. 1067 mm)
48"
(approx. 1219 mm)
54"
(approx. 1372 mm)
PNC-1860
The right-hand movable pinch roller can be moved within this range.
When loading material with a width other than one indicated above, move the right-hand movable pinch roller.
Material with Material with Material with Material with Material with Material with Material with Material with a
a width a width a width a width a width a width a width width of 6"
of 48" and 54" of 42" of 36" of 30" of 24" of 18" of 12"
5
PNC-1210
The PNC-1210 has no middle pinch roller.
Material 6"
(approx. 152 mm)
12" (approx. 305 mm)
18"
(approx. 457 mm)
24"
(approx. 610 mm)
30"
(approx. 762 mm)
The right-hand movable pinch roller can be moved within this range.
When loading material with a width other than one indicated above, move the right-hand movable pinch roller.
PNC-1210
PNC-1210
Roland DG Corp.
(2) Place the roll material on top of the shafts. Place the rolled
sheet here.
Shafts
6
(3) Pull out as much from the roll as needed, and pass the material Pinch roller
from the back of the main unit to the front as shown in the
Guide line
figure.
At this time, line up the right edge of the material with the
guide lines at the front and rear of the grit roller near the
control panel, and pull the material straight out to the front.
Make sure that the edge of the material lies above the grit
rollers. Also check to make sure that the left and right pinch
rollers can be moved to the left and right edges of the material.
Material
(4) Move the left and right pinch rollers so that they are close to Make sure the left and right margins are the same size
the respective left and right edges of the material. When using
Stickers showing the locations of the
a material that is wider than 762 mm (30"), move the middle grit rollers
pinch roller to a position near the center of the left and right
pinch rollers. (The PNC-1210 has no middle pinch roller.)
When doing this, make sure that the grit rollers are under the
pinch rollers.
Seals showing the positions of the grit rollers are affixed to the
areas where the carriage moves. You can use these stickers to
confirm the locations of the grit rollers when the grit rollers
are hidden by the material.
If the pinch rollers are difficult to move, try moving the sheet
loading lever on the back of the unit at the same time.
Move the pinch
(5) Lift the sheet loading lever on the back of the unit to lower rollers to inside
the pinch roller and clamp the material. the edges of the
sheet
Change Pinch
Be sure to move the pinch rollers above the grit rollers when securing a material in the unit.
Roller Position
Moving the pinch roller to the area of the grit roller and pressing the SETUP key causes the message
at right to appear. If this occurs, raise the sheet loading levers and move the pinch rollers to the
proper positions above the grit rollers.
Reposition the material to match this new alignment, then lower the sheet loading levers to hold the material in place.
(6) To secure the rolled material loaded on the sheet hanger, move the stopper to align it with the material, then tighten the stopper
retaining screw securely.
Rolled material
Shaft
7
(7) Close the front cover, then follow the messages on the control panel to use the Close the front cover
and keys to select "Roll" and press the ENTER key. SELECT SHEET
* If cutting is to be performed from the front edge of the material, select ROLL EDGE PIECE
"Edge." PRESS SETUP KEY
(8) Press the SETUP key. The SETUP LED lights up, and the horizontal width of the
WIDTH LENGTH
material is detected and shown on the display. Press the MENUkey once to display
28920 ---
the top menu.
Top menu
* If "Edge" has been selected for the material, then after the width of the
loaded material is detected, the front edge of the material is aligned with the 1 CUT 50cm/s
0.250mm 30gf
cutting-start area.
Press MENUonce.
(9) Press the MENUkey on the top menu once.
Press and align the blinking cursor with the “AREA” display in the top left of AREA AXIS
the screen, then press ENTER key. Move the blinking cursor to the numerals below REPLOT SUBMENU
“LENGTH,” and change the value with the and cursor keys. Then set the Use or to select.
length of the material for cutting. (Ensure a small margin by setting a length that is Press ENTER .
about 0.1 m (3-15/16") longer than the cutting data.) Press ENTER key to fix the
AREA LENGTH
displayed values. Next press or to align the blinking cursor with the “MOVE” MOVE < 5.0m>
display at the lower left of the screen. Press ENTER key to feed a material of the
Use or to change the
length specified in “LENGTH”. value.
Use to select “MOVE.”
Press ENTER.
Check alignment during the test to make sure it is free of offset and alignment problems, diagonal feed problems, and pinch roller
handling problems.
If there are any problems, the material was not loaded straight. Repeat the procedure over again, starting from step (3).
If you turn on “PREFEED” on the display menu, when cutting data is received from the computer (even without using “AREA” to
feed the material), cutting will be performed automatically after feeding 1 m (39-3/8") of material. To prevent material offset and
alignment problems, we recommend making it a habit to feed the material with the “AREA” function after loading.
For details on settings for “PREFEED”, refer to "8 Display Menu Lists."
• If the material curls toward the material face (cut face), it will cause the material to slip when loaded onto the PNC-
1860/1410/1210, and may adversely affect cutting. In this case pre-bend the material downward so that the material
edge is not caught the front cover and guard bar during operation.
• If the material strikes the shaft that is installed on the stand, then remove the shaft.
(1) Pass the material between the pinch rollers and the grit
rollers.
8
(2) Move the left and right pinch rollers so that they are close to the Make sure the left and right margins are the same size
respective left and right edges of the material. When using a material Stickers showing the locations of the
that is wider than 762 mm (30") , move the middle pinch roller to a grit rollers
position near the center of the left and right pinch rollers. (The PNC-
1210 has no middle pinch roller.) When doing this, make sure that
the grit rollers are under the pinch rollers.
Seals showing the positions of the grit rollers are affixed to the areas
where the carriage moves. You can use these stickers to confirm the
locations of the grit rollers when the grit rollers are hidden by the
Material
material.
If the pinch rollers are difficult to move, try moving the sheet loading
lever on the back of the unit at the same time.
Move the pinch
rollers to inside
the edges of the
sheet
(3) Align the right edge of the material with the two guide lines located in Guide line
front of and behind the grit roller on the control panel side, and load
the material so that it is completely straight.
Lift the sheet loading lever on the back of the unit to lower the pinch
roller and clamp the material.
When using a material which is narrower than 762 mm (30") , do not
lower the pinch rollers. Lift the sheet
loading levers
Change Pinch
Be sure to move the pinch rollers above the grit rollers when securing a material in the unit.
Roller Position
Moving the pinch roller to the area of the grit roller and pressing the SETUP key causes the message
at right to appear.. If this occurs, raise the sheet loading levers and move the pinch rollers to the
proper positions above the grit rollers.
Reposition the material to match this new alignment, then lower the sheet loading levers to hold the material in place.
(4) When you close the front cover, the message shown at right appears on the control Close the front cover
panel. Press or to display “PIECE,” then press the ENTER key. SELECT SHEET
ROLL EDGE PIECE
(5) Press the SETUP key. The tool carriage will move from side to side and the material will
move forward and backward to detect the size of the material. After this sensing is PRESS SETUP KEY
finished, the front edge of the material is aligned with the cutting starting position.
(6) If material offset or alignment problems become apparent while the 1860/1410/1210 is WIDTH LENGTH
28920 150
scanning the piece in step (5) above, the material has not been loaded straight. Be sure to
load the material straight. Set the movable left and right pinch rollers inside the material
edges.
9
To Perform Long Cutting
When performing cutting over a length of 1.5 m (60") or more, first feed out the required length of material. Then follow
the steps below to load the material.
2 25 mm
(1")
or more
5 Close the front cover.
3 25 mm
(1")
or more
10
3-4 Selecting the Interface
Use the control panel to select the type of interface.
The selected interface type and communication parameters are stored in memory even after the power is switched off.
To change the interface type or the communication parameters, configurations must be re-entered.
(1) Set the output port for the computer (or software) to “Parallel” for a parallel
connection, or to “Serial” or “RS-232C” for a serial connection.
* The method used to make this setting varies according to the software
used. For details, refer to the manual for your software.
(3), (4)
AREA AXIS
(2) Close the front cover. REPLOT SUBMENU
Use or to select.
(3) Press the MENU key to display the menu shown at right.
Press ENTER .
(4) Use the and keys to move the blinking cursor to “SUBMENU” and press (5)
CROPMARK UPDOWN
ENTER key. OVER-CUT CALIB
Press MENU twice.
(5) Press the MENU key twice.
(6)
(6) Use the and keys to move the blinking cursor to “I/O” and press ENTER VS-COMND FS-CMND
key. COMAAND I/O
Use or to select.
* The PNC-1860/1410/1210 is equipped with an auto-interface function, and Press ENTER .
so when left set to “AUTO,” it will automatically determine whether a parallel
(7)
or serial connection is used. When a serial connection is used, however, it INTERFACE
PARA SERI<AUTO>
is necessary to set the communication parameters to match those set for the
computer (and/or software). Use or to select.
Press ENTER .
(7) Pressing the or key will sequentially display “PARA,” “SERI,” and
“AUTO.”
If you are using a parallel connection, display “PARA” or “AUTO” and press (8)
PROTOCOL 1
ENTER key. STOP DATA PARITY
If a serial connection is used, display “SERI” or “AUTO” and press ENTER key.
Then set the communication parameters for the PNC-1860/1410/1210 to match Press MENU .
11
3-5 Cutting Test - Setting Cutting Speed, Blade Force, and Blade Compensation
For optimum performance, it is necessary to set cutting conditions that match the material, giving consideration to the material's
thickness and type of material. The PNC-1860/1410/1210 has an internal "cutting test" to check the cutting conditions. This
“cutting test” allows you to determine settings for the cutting speed, blade force and the amount of offset.
Experiment with different settings for different types of material and adjust the configuration accordingly.
Procedure
(1) Install a blade and load a material, then close the front cover (see "3-2 Installing the
ORIGIN SET->ENTER
Cutter" to "3-3 Loading the Material). O 0
Press the MENU key until the screen shown at right appears. Use the , , and
keys to move the tool carriage to the place where the cutting test is to be performed. The
tool carriage cannot be moved by pressing the , , and keys unless the
display shows the screen right.
• Note that an area of approximately 2 square centimeters (a little less than a square inch) is
required to make a test cutout (given that the tip of the cutter after it has moved is at the
Peel off first
origin at lower-left).
Then, peel this off
(2) Press the TEST key for 0.5 seconds or more. Cutting test starts.
The resulting cutouts will then appear as illustrated.
(3) Confirm the cutting speed and the blade force. Peel off the round section
(marked by ). Confirm that you can peel off the square section Origin
(marked by ), but do not remove it. Also remove the square (Position of the tool installed
in step 1)
section (marked by ). If the blade leaves a slight trail on the
carrier paper, you have achieved optimum cutting speed and blade force.
Blade force
Setting range: 20—350 gf
(in increments of 10 gf)
• Use the and keys to move the blinking cursor to the item to be set.
• Then use the and keys to change the numerical value, and press the ENTER key to enable the setting.
12
Incorrect cutting conditions may cause symptoms such as those described below. Take care to ensure that the cutting conditions are
correct.
Cutting speed
Cutting takes more time. Too slow Too fast Some parts of the sheet remain uncut.
Blade force
Some parts of the sheet remain Too small Too large • The sheet is easily torn.
uncut. • The cutter requires frequency replacement
• The blade pierces the sheet.
• Cutting extends through the base paper, and
normal advancing of the sheet becomes impossible.
• The unit suffers damage.
Blade compensation
Corners are rounded. Too small Too large Corners flare outward, with "horns."
Software Setting
When cutting with commercially available application software, select PNC-1860/1410/1210 as the setting for the output device.
If the PNC-1860/1410/1210 cannot be selected, choose any model in the PNC-1850, PNC-1200, PNC-950 or PNC-900. (These
models support CAMM-GL III.)
Select either the parallel (Centronics) or serial (RS-232C) interface. Choose the one that the host computer and the PNC-1860/
1410/1210 are connected by.
Cutting is paused and the screen shown at right appears on the display. PAUSE ON
CONT. STOP VIEW
Continue cutting
Make sure the blinking cursor is at "CONT" and press the Abort cutting
ENTER key. Cutting is resumed. First of all, stop the flow of data being sent by the
computer.
Use the and keys to choose "Stop" and press the
ENTER key. Cutting stops and the display returns to the top
menu.
Checking the Status of Cutting
The tool carriage can be moved toward the control panel to allow the cutting status to be checked visually.
Use the and keys to choose "VIEW" and press the ENTER key. The tool carriage moves toward the control panel. To resume
cutting, follow the procedure described in "Continue cutting" above.
13
Continuing Cutting
Cutting after changing the material
Again carry out the procedure described from “3-3 Loading the Material” to “3-6 Downloading Cutting Data” .
* There is no need to perform the procedure described under “3-4 Selecting the Interface.” Also, if a material of the
same type is used, there is no need to perform a cutting test.
The Replot function calls up all data in the data buffer and performs cutting with this data. When performing replotting, follow
the steps below to delete the data in the data buffer before send the data to be replotted from the computer.
(1) Press the MENU key until the screen shown at right appears, then use the and keys to
AREA ROTATE
select "Replot" and press the ENTER key.
REPLOT SUBMENU
(2) Use the and keys to select "Clear" and press the ENTER key to delete the data in the
data buffer.
REPLOT
START CLEAR
14
3-7 Applying the Completed Cutout
• Make sure beforehand that the surface where the work is to be stuck is clean and free of all dust or oily deposits.
• When applying the work to a transparent surface, such as a window, you can use a water-based pen (which can be
wiped off) after wards to mark guidelines on the reverse side of the glass, to aid in getting the work aligned
properly.
• If you discover after it is stuck in place that air bubbles were trapped under the work, use a needle to puncture them.
Then you can smooth out the material so that it sticks securely.
(1) Open the front cover. (3) Stick application tape over the completed work.
For roll material Press down firmly or use a squeegee on the application
Use the cutter tool to cut off the completed portion tape to remove air bubbles. If you do not press firmly
from the roll.
enough the cut area will not stick to the surface.
For a Flat Material (Standard-size
Material, Cut Material, Scrap, Piece, Etc.)
Lower the sheet loading levers and remove the
material from the PNC-1860/1410/1210.
* If a portion that can still be cut remains, then
instead of removing the material, use the cutter
tool included with the unit to detach the portion
that has been cut, just as is done when using a
rolled material.
(4) Carefully apply the work at the desired location, while
keeping it as straight as possible. Rub over the
application tape to make sure the work is firmly stuck
(2) Strip/Weed away all unneeded portions from the in place. Then peel off the application tape.
completed work.
*You should have weed
boarders or rectangles
drawn around work to
Tweezers
facilitate weeding.
3-8 When Completed Cutting Press down the sheet loading levers
(1) When cutting is finished, press down the sheet loading
levers and remove the material.
(2) If a cutter was used, wipe the cutter with a soft cloth to
remove any pieces of the material that may be adhering Material
to it.
If a pen was used, remove the pen from the tool carriage
and cap it securely.
(3) Turn the power off. If you not intended to used the unit
for an extended period of time, you should pull the plug
for the power cord out of the outlet.
15
4 CARE AND MAINTENANCE
16
5 ABOUT THE CUTTING AREA
Cutting area
Approx. 1 mm
Movable pinch roller (left)
(about 0.04")
24998 mm (984-1/8")
10 mm
(3/8")
Approx. 15 mm
(about 9/16")
Use the and keys to move the blinking cursor (" ") and choose a setting.
Then use the and keys to change the value (or the selection) and enable the setting by pressing the ENTER key.
1 CUT 50cm/S • To return to the menu selection screen from any of the menu
value setting screens, press the MENU key.
0.250 30gf • To return to the previous screen without changing the numerical
settings, pressing the MENU key without pressing the ENTER
Press the MENU key to change to key.
the next menu
17
7 DISPLAY MENUS FLOWCHART
For details about each of the menus, see the "8 Display Menu Lists."
18
Openning message
PNC-1860 PNC-1410 PNC-1210 ENGLISH JAPANESE DEMO CUT
Roland DG Corp. Roland DG Corp. Roland DG Corp. GERMAN FRENCH
ENGLISH/JAPANESE/
After loading a sheet, Use or to select.
GERMAN/FRENCH/
SELECT SHEET close the front cover. SPANISH/ITALIAN Press ENTER to enable the setting.
ROLL EDGE PIECE
SPANISH ITALIAN
ROLL/EDGE/PIECE MENU
Use or to select.
Press ENTER
PRESS SETUP KEY LOADING SHEET
SETUP
ROLL
WIDTH LENGTH
14612 ------
Top menu 1—85 1—85 (in increments of 1 cm/s)
1— 8 (in increments of 1 cm/s) NORMAL/HEAVY/ H-SPEED
1 CUT 50cm/s UP 50cm/s NORMAL
0.250mm 30gf
0—1.000 20—350
(in increments of (in increments of 10 gf)
0.025 mm) MENU Align the blinking cursor at the value, press or to change the value, then press ENTER to confirm.
After making the setting for [LENGTH], press or to move the blinking cursor to [MOVE] and press ENTER .
AREA AXIS AREA AREA LENGTH -24.9 m—+24.9 m (in increments of 0.1 m.) to feed the sheet at the set length.
REPLOT SUBMENU MOVE < 1.0m> * When [FEET] is selected for [AREAUNIT] : -82.17—+82.17 (in increments of 0.33 feet)
CROP-MARK BASEPOINT->ENTER
0 0
AXIS AXIS ROTATION
<0deg> 90deg
ALIGNPOINT->ENTER
0deg / 90deg
0 0
MENU
MENU
CROPMARK SETTING CROPMARK SETTING
REPLOT REPLOT COMPLETED! FAILED,SET AGAIN
START CLEAR
START/CLEAR
Pressing ENTER moves the blade up or down.
SUBMENU CROPMARK UPDOWN UPDOWN UP/DOWN ->ENTER Pressing , , , or moves the cutter in
OVER-CUT CALIB MOVE ->CURSOR the +Y, -Y, -X, or +X directions, respectively.
Page where
MENU Explanation Default
explained
Determining the type of sheet loaded
SELECT
SHEET
This selects the type of sheet to be used ("Roll," "Edge," or "PIECE"). - 8, 9
This sets the speed blade for during cutting. Perform a cutting test and set
** cm/s 50 cm/s 11, 12, 23
the conditions to match the loaded sheet and the installed cutter.
This sets the amount of offset for the blade during cutting. Perform a
cutting test and set the conditions to match the loaded sheet and the
*.**mm installed cutter. When using the included test sheet and blade or 0.250 mm 11, 12, 23
equivalent parts, cutting can be performed using the factory-default
settings.
This sets the force for the blade during cutting. Perform a cutting test and
**gf 30 gf 11, 12, 23
set the conditions to match the loaded sheet and the installed cutter.
If you want the curves of circles and arcs to be cut smoothly, set this to
SMOOTH- “ON.” When on, however, small text or intricate designs may also be cut
ON -
ING with rounded corners. If this happens, change the setting to “OFF” and
perform cutting again.
This sets the cutting quality. Ordinarily this is left set to "NORMAL."
NORMAL
When rapid cutting is desired, such as when cutting a large sheet, set this
(CUT NORMAL 25
to "HI-SPEED." When load is large, or if the sheet is not cut smoothly,
QUALITY)
or when small text is to be cut attractively, set this to "HEAVY."
This sets the speed of movement when the tool is raised and moves to the
UPSPEED 85 cm/s -
next position for cutting during a cutting operation.
g g g
This selection is normally left set to "OFF," and is set to "ON" when
1 OFF 20
cutting especially attractive corners is desired. When cutting small text
OVER CUT
or intricate graphics, however, this should be set to "OFF" to avoid
Setting the origin point
Set a user origin at an arbitrary point on the sheet.
ORIGIN SET After the sheet has been loaded, be sure to set the origin to the bottom - 13
left of the sheet.
20
Page where
MENU Explanation Default
explained
Feed the loaded sheet
This moves the sheet by the length to be cut before actual cutting is
performed, making it possible to ensure that the sheet will not slip or
AREA come loose during cutting. When performing continuous cutting on the 1.0 m 8
same sheet, this can also be used to make sure that there is enough
remaining sheet to cut the data that will be sent.
AREA UNIT
Sets the units used to specify length in display menu “AREA”. Units METRE 8
may be set to either “METRE” or “FEET”.
Set to on for automatic sheet feed at cutting. If this is set to on, when
cutting data is sent from the computer, the plotter will automatically
execute cutting after a 1 m (39-3/8") feed.
After the sheet is loaded be sure to feed the sheet by the length needed for
PREFEED cutting with the “AREA” function. (Some data may cause feed over 1 m OFF 8
(39-3/8"), such as when the next point of movement is located more than
1 m (39-3/8") to the rear.)
* If the “AREA” function is used to feed the sheet in advance, the sheet
will not be automatically fed even when “PREFEED” is set to on.
Correct for the cutting distance error based on actual measurement
This is used when cutting sheets with alignment marks (crop marks)
3 printed around the graphics, such as for making stickers or seals. The
- 20
CROPMARK crop marks are set as reference points and correction points, enabling the
graphics to be cut with accuracy.
Correct for the cutting distance error based on actual measurement
This adjusts the respective distances of the X and Y axes. Compare the
CALIB actual measurements of the cutting results with the data sent from the 0.00% -
computer to calculate and set the distance adjustment value.
Repeating the same cutting - Deletes any data in the replot buffer
This cuts the data in the replot buffer. Selecting "Clear" causes existing
REPLOT - 13
data in the replot buffer to be deleted.
Selecting the instruction set
This selection enables the type of instructions that are understood by the
unit. You can set the unit to accept either CAMM-GL III mode 1
instructions (“1”) or mode 2 instructions (“2”).
COMMAND When set to “AUTO,” the PNC-1860/1410/1210 automatically detects
AUTO 12
MODE the type of instructions first received after turning on the power, and sets
itself to accept those instructions.
To change the type of instructions, first change the setting, then switch
the power to the unit off and back on again.
Selecting the connection interface
This selects the interface for connecting a computer to the PNC-1860/
1410/1210. Set this to “PARALLEL” for a parallel connection or to
“SERIAL” for a serial connection.
INTERFACE AUTO 10
When set to “AUTO,” the PNC-1860/1410/1210 automatically detects
whether a parallel or serial type interface is used when data is first
received after turning on the power, and sets itself accordingly.
Setting the protocol for a serial connection
STOP BIT This marker tells the system when a character data set end. 1 10
DATA BIT The size (length) of one block of data. 8 10
PARITYMODE Parity is used to check whether data was received correctly. NONE 10
BOUD RATE Determines the speed of data transmission. 9600 10
Sets the handshake mode for when the PNC-1860/1410/1210 is
HANDSHAKE H-WIRE 10
connected the host computer via the serial interface.
21
Page where
MENU Explanation Default
explained
Giving priority to settings from the computer
This is normally set to "IGNORE" when performing cutting. When a
tool-selection instruction (SP instruction) is sent from the computer
TOOL-CNG while this is set to "EGNORE," the SP instruction is ignored and
IGNORE 23, 24
COMMAND operation continues without pause. When set to "EFFECT," SP exchange
instructions are accepted and operation pauses. If tool change is needed,
open the front cover, change the tool, then press the ENTER key.
To perform cutting at the speed determined by a VS command (tool speed
VS setting command) sent from the computer, set this to "EFFECT." When
IGNORE 11
COMMAND set to "IGNORE," cutting is performed using the values for "** cm/s" and
"UPSPEED" set at the top menu.
To perform cutting at the tool force determined by an FS command (tool
FS force setting command) sent from the computer, set this to "EFFECT."
IGNORE 11
COMMAND When set to "IGNORE," cutting is performed using the values for "** gf"
set at the top menu.
Other setting
ENGLISH,
JAPANESE,
The PNC-1860/1410/1200 is capable of displaying all its menus in
GERMAN,
either of six languages, English, French, German, Spanish, Italian ENGLISH -
FRENCH
SPANISH, and Japanese.
ITALIAN
This sets the type of unit for coordinate values that appear on the display.
UNIT Set this to “MECHANICAL UNIT” for display in cutting coordinate units MACHINE -
(1 = 0.025 mm), or to “MILLIMETER” for display in millimeters.
This performs an operation check when the PNC-1860/1410/1210 is not
DEMO CUT - -
working correctly.
This moves the tool up or down. It also moves the tip of the blade in any
UP/DOWN of four directions (-X, +X, -Y, or +Y).
- -
MOVE With the tool down, the tool carriage can be moved with the four cursor
keys to cut the sheet.
1 OVER CUT
Cutting results differ as shown in the following figures depending on whether the Overcut function is on or off.
2 ROTATE
Whenever you employ the Rotate function (which allows you to rotate a character 90 degrees), the origin will be located at the
material’s lower-right.
Y X
Origin X Y Origin
22
3 CROPMARK
This is used when cutting around pre-printed graphics on a material, such as when making stickers or seals. With the PNC-1860/1410/
1210, a material is always loaded parallel to the unit. This means that unless the graphics to be cut have been printed parallel to the
material, the cutting lines become shifted from the graphics, and it becomes impossible to accurately cut around the graphics (see Figure
A below). If the printed graphics have crop marks, the positions of the crop marks can be stored in memory and used as reference points
by the PNC-1860/1410/1210. By making this setting, it becomes possible to cut around graphics with accuracy even when the graphics
have not been printed parallel to the material (Figure B).
A When the crop mark setting has not been made B When the crop mark settings has been made
Material Material
Accurate cutting
around the graphic is
not possible
Within 5 degrees
The steps for making the crop mark setting are described below. Please refer to the figures shown below while making this setting.
Crop marks are set with the front cover open. Take care to ensure that the hands do not get caught in
the tool carriage as it moves.
• The crop mark setting cannot be made if the angle of the base point and the align point is more than 5 degrees.
• Crop marks cannot be set when the "ROTATE" display menu is set to "90 deg."
Load the material (with pre-printed graphics) and install the alignment tool included with the (1)
PNC-1860/1410/1210. The alignment tool is installed in the same way as the blade holder.
AREA AXIS
(1) Press the MENU key until the screen shown at right appears, then use the and keys to REPLOT SUBMENU
select "SUBMENU" and press the ENTER key. (2)
(2) When the screen shown at right appears, press the ENTER key to change to menu for setting the CROPMARK UPDOWN
base point. OVER-CUT CALIB
(3)
(3) Use the , , , and keys to move to the tool carriage to a position below and to the
left of the crop mark printed on the material. Press the TEST key to move the tool up and BASEPOINT->ENTER
0 0
down several times, and line up the alignment tool with the center of the crop mark. After the
alignment tool has been positioned correctly, press the ENTER key. The display then advances (4)
to the menu for setting the align point. ALIGNPOINT->ENTER
0 0
(4) Use the , , , and keys to move to the tool carriage to the crop mark printed at the
lower right of the material. Press the TEST key to move the tool up and down several times, (A)
and line up the alignment tool with the center of the crop mark. After the alignment tool has CROPMARK SETTING
been positioned correctly, press the ENTER key. COMPLETED !
(5) When the crop mark setting has been made successfully, the display shows screen (A), then (B)
returns to the screen shown in step (2). Replace the alignment tool with a blade. If the crop CROPMARK SETTING
mark setting could not be made, the display shows screen (B) before returning to the screen FAILED,SET AGAIN
shown in step (2). If this happens, reload the material and make the setting again.
23
9 BLADES AND MATERIALS
This section indicates the proper cutting conditions for various types of materials, as well as blade lifespans. Cutting conditions
and blade life vary according to the hardness of the material and the usage environment. Making the settings for the conditions
described below does not automatically guarantee attractive cutting results in all situations. Before performing actual cutting, be
sure to carry out a cutting test and make any necessary adjustments (see "3-5 Performing a Cutting Test"). If the material is not
cut through completely even when the tool force is increased by 50 to 60 gf more than the tool force values shown below, it
means that the useful life of the blade has ended. Replace with a new blade.
Amount of cutter
Blade Material Tool force Speed Life of a blade
blade extention
ZEC-U1005 General Signage Vinyl 50—150 gf 85 cm/sec 0.25 mm 8000 m
General Signage Vinyl 30—100 gf
ZEC-U5025 Reflective vinyl 120—200 gf 85 cm/sec 0.25 mm 4000 m
Fluorescent Vinyl 100—200 gf
Rubber sheet for Varies according
ZEC-U1715 100—200 gf 20 cm/sec 0.25 mm
sandblasting stencil to sheet type
* The values for lifespan are intended to serve as a general guide when cutting materials of identical type.
Rubber materials for sandblasting stencils which can be cut: Materials with a material thickness of 1 mm or less
Materials with only carrier paper on both flanks of the material (Position
the left and right pinch rollers above the strips of carrier paper.)
Materials with carrier paper which is hard enough to withstand material
feed
Material
1 mm or less
Carrier paper
15 mm or more
24
10 PLOTTING ON PAPER MEDIA
Before cutting, plotting using pen and paper can ensure that your design is correct without wasting materials.
This feature can also be used to plot template designs on thick materials that may not be able to be cut.
* Since the design of the PNC-1860/1410/1210 differs inherently from that of dedicated plotters, it does not accommodate
functions such as high-speed plotting, automatic pen changes, pen dry protection, or the like.
Do not load coated paper. The coating may flake or peel off and adhere to the grit rollers, making it impossible to perform
cutting (or plotting) correctly.
5. Cut quality (see "7 Display Menu Lists/Setting cutting conditions/NORMAL (CUT QUALITY)" )
Set this to "Normal."
(1) Press the MENU key until the screen shown at right appears, then use the and keys to select AREA AXIS
REPLOT SUBMENU
"SUBMENU" and press the ENTER key.
(2) Press the ENTER key, then press the MENU key twice the screen shown at right appears. Then use the
and keys to select "TOOL-CHG" . UNIT AREAUNIT
TOOL-CHG PREFEED
(3) Press the ENTER key to display the screen shown at right, then use the and keys to select
"EFFECT" and press the ENTER key.
TOOL-CHG COMMAND
IGNORE <EFFECT>
Depending on the setting made for "6. Setting for pen change instructions," operation is paused when
a tool-change instruction is received while plotting is in progress. To change the tool, open the front TOOL-CHG:TOOLNO2
cover and exchange the tool. Then press the ENTER key to resume cutting.
25
11 WHAT TO DO IF....
11-1 What to do if....
PNC-1860/1410/1210 troubleshooting
Connect the power cord included with the PNC-1860/1410/1210 to the unit,
Is the power cord connected correctly? and plug the other end securely into an electrical outlet (see “3-1
Installation and Connections” on page 3).
Is the PNC-1860/1410/1210 power on ? Turn on the power.
Close the front cover when performing cutting (see “3-3 Loading a Sheet”
Is the front cover closed?
on page 5).
If the screen shown at rights is displayed,
PAUSE ON
it means that operation is paused.
CONT. STOP VIEW
Follow the steps described in " Pausing Cutting"
Is the PNC-1860/1410/1210 in the temporary
To resume cutting, use the and keys to select "CONT," then press the
halt state ? Is operation paused?
key.To abord cutting, first stop the flow of cutting instructions from the
computer. And use the and keys to select "STOP," then press the ENTER
key.
If connected via the serial port, do the
communication parameters for the PNC- At the display menus, make the correct settings for the communication
1860/1410/1210 match those of the parameters (refer to “3-4 Selecting the Interface” on page 11).
computer ?
Check the following items:
• DIP switches • Memory switches • Interface board • Communication
Is the computer set up correctly ?
parameters • Other settings
Read the computer user’s manual and set it up correctly.
The type of cable you need is determined by your computer and the software
Are the computer and the PNC-1860/1410/
you are using. Even if the computer is the same, running different software
1210 linked with the right cable ?
may require a different cable. Use the cable specified in your software.
Are the computer and the PNC-1860/1410/ Correctly connect the computer and the PNC-1860/1410/1210 (see “3-1
1210 connected correctly? Installation and Connections” on page 3).
At the display menu, make the correct setting for the interface connecting
Is the interface setting correct? the computer and the PNC-1860/1410/1210 (refer to “3-4 Selecting the
Interface” on page 11).
Check the following items:
• Output port selection • Output device selection • Output port open
Is the OS set up correctly ?
• Communication Parameters • Other settings
Check the OS’s user’s manual and set it up correctly.
Check the following items:
• Output device specifications (select a device name that matches the
instruction system.
Are the application software settings
If the wrong device is selected an incorrect instruction may be output,
correctly ?
resulting in an error).
• Communication Parameters • Other settings
Check the software user’s manual and set it up correctly.
26
A message appears on the display
The location of one or more of the pinch rollers is not correct.
Change Pinch If this happens, raise the sheet loading levers and move the pinch rollers to the
Roller Position proper positions above the grit rollers. Reposition the sheet to match this new
alignment, then lower the sheet loading levers to hold the sheet in place.
This is displayed when the front cover is opened during cutting. Cutting
CLOSE COVER operation is halted, and the message is displayed on the screen.
Cutting restarts when the cover is closed.
This is displayed when the material has been loaded at a position where the
sheet sensor does not function.
Sheet Set Error Follow the steps under "3-3 Loading Material" on page 5 to load the material so
Set Sheet Again that it is positioned above the sheet sensor.
This is displayed when the sheet is removed after pressing the SETUP key.
Load a sheet and press any key to cancel the error message.
Shows motor error status.
Motor Error This is displayed when the PNC-1860/1410/1210 is heavily loaded, such as
Power ON Again during a paper jam, when heavy stock is cut across a long distance without
initial sheet feed, or when the sheet is abruptly pulled from the roll during
cutting.
In this case, turn the power off and back on again (if a paper jam has occurred,
clear the jam before turning the power back on).
For large cutting data with a roll sheet, use the “AREA” function on the display
menu to feed the roll sheet by the length of the cut (ensure a small margin by
setting a length that is about 0.1 m longer than the cutting data).
When using a thick sheet, change the display menu setting from "NORMAL" to
"HEAVY."(see “8 Explanation of display menu /"NORMAL" (CUT QUALITY) .
If the above message is displayed even after"NORMAL" (CUT QUALITY) is set
to “HEAVY,” turn the power off and then back on again, and reduce the “**cm/
s” value in the display menu. See “** cm/s Setting cutting speed” on page 12.
Is the blade chipped ? If it is, replace it with a new one (see “3-2 Installing the cutter” on page 4).
The sheet slips away from the pinch rollers during the cutting process
If a sheet with holes for sprocket feed is being used, placing the pinch roller
Is a sheet with sprocket holes being used? above the hole portion may cause the sheet to slip. Be sure to set the pinch
roller over the sheet to the inner side of the hole portion.
If a flat sheet (such as a standard-size sheet
or cut sheet) has been loaded, has the When loading the sheet, select “PIECE” for the “SELECT SHEET” display menu
“PIECE” setting been selected for the sheet (refer to “3-3 Loading a Sheet” on page 9).
type?
Make sure that the left and right edges of the sheet do not touch the inner
Is the sheet being cut blocked at some surfaces, front cover of the PNC-1860/1410/1210 during cutting. Such contact
position? may not only damage the sheet, but could also make normal sheet advancing
impossible and cause the sheet to slip.
27
The sheet slips away from the pinch rollers during the cutting process
If the front edge of the sheet you are working with is at an angle, cut off the odd-shaped
part to make it straight, then align it so that it is parallel with the grit roller.
If the sheet is fed for a long distance, the sheet will be less likely to slip out of
alignment if the pinch rollers are moved inward slightly (5 to 25 mm).
Make sure the sheet is parallel When a roll sheet is loaded, use the display menu “AREA” function to feed a sheet by
with the grit roller. the length to be used (ensure a small margin by setting a length that is about 0.1 m
longer than the cutting data), make sure the pinch rollers are still in contact with the
sheet (not off the left or right edges, or on the edges), and then cut.
If the sheet is pulled while cutting it is more likely that sheet misalignment and motor
errors will occur.
Er2:Wrong Number
of Parameters Appears if the number of parameters differs from the permissible number.
Er3:Out of
Parameter range Appears if the value specified for a parameter is out of the permissible range.
Er5:Unknown
Appears if an unusable character is specified.
Character Set
Appears if an output instruction is sent from the computer during execution of a previous
output instruction. More precisely, there is a certain amount of delay between the moment
Er10:Output an output instruction is given and the instant actual output begins. This error message
Request Overlap appears if the new output request arrives during this delay time. (The delay time can be set
using the [ESC].M instruction.)
Er11:Command Appears if a device control instruction that the PNC-1860/1410/1210 cannot interpret is
Not Recognized sent.
Er12:Wrong
Appears if an invalid parameter has been specified for a device control instruction.
Parameter
Er13:Out of Appears if the value for a device control instruction parameter exceeds the permissible
Parameter range limit.
Er14:Termination Appears if the number of parameters for a device control instruction is more than that
Error permissible.
Appears if a framing error, parity error, or overrun error occurs at the time of data
Er15:Framing/ reception.(There is a problem with one of these settings: Baud Rate, Parity, Stop Bits, or
Parity Error Data Bits. The protocol settings for the PNC-1860/1410/1210 must be made correctly in
order to match the settings your computer is set to use.)
Appears if the I/O buffer has overflowed.(There is a problem with the connecting cable, or
Er16:Buffer the settings for Handshaking. Make sure you are using a cable appropriate for the
Overflow computer being used. Also, check that the setting for Handshaking is correct.)
Er18: Appears if a communication error other than “Er10” through “Er16”, one uninterpretable
Indeterminate by the PNC-1860/1410/1210, occurs during data communications.
28
12 SUPPORTED INSTRUCTION SETS
A "CAMM-GL III Programmer's Manual" is available for separate purchase for those wishing to create their own programs for this
machine. For further information, please contact the nearest Roland DG Corp. dealer or distributor.
: Compatible.
: Ignored.
:Incompatible
• mode 1
Instru- Compati- Instru- Compati- Instru- Compati- Instru- Compati- Instru- Compati-
ction bility ction bility ction bility ction bility ction bility
H R P C K
D L S E T
M B Q A ^
I X N G
• mode 2
Instru- Compati- Instru- Compati- Instru- Compati- Instru- Compati- Instru- Compati-
ction bility ction bility ction bility ction bility ction bility
AA ER OE PT SP
AR EW OF PU TL
CA FT OH RA UC
CI IM OI RR VS
CP IN OO SA WD
CS IP OP SC WG
DF IW OS SI XT
DI LB OW SL YT
DR LT PA SM
DT OA PD SR
EA OC PR SS
29
13 CHARACTER SET
Automatic backspace
30
13 CHARACTER SET
Hexe-
decimal
Decimal Cho<OC'I• HI Hexa·
dtcirnel
I
Decimal Cheracter Mt
u H
IIIIIIeJIIIIIIIIIII
J J J J J J 0 1\ J J J w J J J J J J J
2A
* * • • * * I * * * * * * * * * * *
++++++ + + + + + + + + + + + n K K K K K K ue K K K K K K K K K K K
28
2C
43
44 -• ~ ~
~ ~ l l L L l l a ) l L L l L l L L L L L
20 45 - - - - - - u~ - - - - - - - - - - - ~ 77 M MMM MM ~ ~ M MMMMM MM M MM
2E 46 0 3 ~ n N N N N N N 0 "- N N N N N N NN N N N
2F 47 I I I I I I £ ~ I I I I I I I I I I I ~ ~ 0 0 0 0 0 0 (j ~ 0 0 0 0 0 0 0 0 0 0 0
30 48 oooooo--ooooooooooo 50 60 P P P P P P A ~ P P P P P P P P P P P
31 49 1 1 1 1 1 1 p 1 1 1 1 1 1 1 1 1 1 1 51 61 Q Q Q Q Q Q i ~ Q Q Q Q Q Q Q Q Q Q Q
32 50 2 2 2 2 2 2 ~ 2 2 2 2 2 2 2 2 2 2 2 ~ ~ R R R R R R 0 ~ R R R R R R R R R R R
33 51 3 3 3 3 3 3 ? 3 3 3 3 3 3 3 3 3 3 3 ~ ~ s s s s s s ~ £ s s s s s s s s s s s
34 52 4 4 4 4 4 4 CI 4 4 4 4 4 4 4 4 4 4 4 ~ ~ T T T T T T A~ T T T T T T T T T T T
35 53 5 5 5 5 5 5 c ~ 5 5 5 5 5 5 5 5 5 5 5 ~ 66 u uu u u u i ] u u u u u u uu u u u
36 54 6 6 6 6 6 6 Nn 6 6 6 6 6 6 6 6 6 6 6 66 66 vvv vv v0 3 vv vv vvvv vvv
37 55 7 7 7 7 7 7 " ~ 7 7 7 7 7 7 7 7 7 7 7 ~ ~ w w w w w w i! 7 w wwww w ww ww w
38 56 888888 i?88888888888 66 66 X X X X X X I ~ X X X X X X X X X X X
39 57 9 9 9 9 9 9 ~ 7 9 9 9 9 9 9 9 9 9 9 9 66 66 y y y y y y i ~ y y y y y y y y y y y
3A 58 D ::J ~ ~ zzzzzz0 v zzzzzzzzzzz
38 59 i. ., 66 91 [ [ [0 l [uo 111~1· [' iA~
3C 60 < < < < < < ¥ ~ < < < < < < < < < < < ~ n \ { c ~ i • ~ ? \ 0 0 0 0 c \ c ~ c0
30 61 ==== = =§ ~ =========== ~ ~ JJJ 0]] 1 :;J AAAO§J e~oA.
> > > > > > J ~ > > > > > > > > > > > ~ ~
• t [': i! :·: • B ' • - 0 - • • • • • • •
.
3E 62
3F 63 ? ? ? ? ? ? ¢
a
? ? ? ? ? ? ? ? ? ? ?
~
A9 @ @ @§ a @ § § § o E
~ 66 :-- :,-: ,,.; ~;: ::--~ :-- ~ e
40 64 @@@@@ 60 ~ u
He••·
decimal
Decimal Character 181
code code 0 I 1 3 4 6 7 I 9 30 )I 32 ]3 )4 35 36 37 31 39
61 97 A a a a a a a a a a a a
a a a a a a
62 98 ooooooa b b b b b b b b b b b
63 99 c c c c c c D c c c c c c c c c c c
64 100 d d d d d d d d d d d d d d d d d d
85 101 e e e e e e i e e e e e e e e e e e
66 102 ffffttl: t f f t t t f f f t f
67 103 g g g g g g 6 g g g g g g g g g g g
66 104 n n n n n n o n n n n n n n n n n n
69. 105 l l l l l l 0 l l l 1 1 1 l l l 1 l
6A 106 J J J J J J 0 J J J J J J J J J J J
68 107 k k k k k I< 5 k I< k k k k k k k
I< I<
BC 108 1111115 1 1 1 1 1 1 1 1 1 1 1
60 109 mmmmmmU mmmm mmmmmmm
6E 110 n n n n n n Y n n n n n n n n n n n
SF 111 0 0 0 0 0 0 y 0 0 0 0 0 0 0 0 0 0 0
70 1 i2 p p p p p p p P P P P DP P P P P P
71 113 Q Q Q Q Q Q D Q Q Q Q Q Q Q Q Q Q Q
72 114 r r r r r r r r r r r r r r r r r
73 115 s s s s s s s s 5 5 5 5 5 5 5 5 5
74 116 t t t t t t t t t t t t t t t t t
75 117 u u u u u u uuuuuuuuuu_~
76 116 v v v v v v - v v v v v v v v v v v
77 119 w ww w w w 1: w w ww w w w www w
78 120 X X X X X X .,
1
X X X X X X X X X X X
79 121 y y y y y y il y y y y y y y y y y y
7A 122 z z z z z z fl. z z z z z z z z z z z
taai!ae I a . a i!
1 1
:HL~E ~»
78 123
7C 124 1 1 I oo0ou1 0 " c 0
70 125 I
~L~UEj I I A A A u e.. I e c ~ A
7E 128
)
- ~~ 1 · [~~]L:J - t - - 0 - B - i - I
7f 127
II
L _j Automatic backspace
30
1
SPECIFICATIONS
SPECIFICATIONS
For items indicates by an asterisk "*", please see the following page.
31
( )
* The following conditions must be satisfied:
- Material type: 3M Scotchcal Mastercut Film, ARLON Series 2100
- Special stand (a roll material must be set at the rear and on the inner sheet hanger)
- Side margins: 25 mm (1") or more for both the left and right margins
- Front margin: 25 mm (1") or more
(After loading the material, using the display menu to select “EDGE” as the material type automatically sets a front margin of 25 mm (1").)
- Use of the display menu’s “AREA” function to perform feed of the material length plus 0.2 m and set the material correctly
- Cutting of the following data one time
Interface Specifications
Parallel
Standard In compliance with the specifications of Centronics
Input signals STROBE (1 BIT), DATA (8 BIT)
Output signals BUSY (1 BIT), ACK (1 BIT)
Level of input/output signals TTL level
Transmission method Asynchronous
Serial
Standard RS-232C specifications
Transmission method Asynchronous, duplex data transmission
Transmission speed 2400, 4800, 9600, 19200 (selected using panel keys)
Parity check Odd, Even, or None (selected using panel keys)
Data bits 7 or 8 bits (selected using panel keys)
Stop bits 1 or 2 bits (selected using panel keys)
Handshake DTR or Xon/Xoff (selected using panel keys)
22 4 D2 100 Ω
** =
21 3 D1
20 2 D0
19 1 STROBE
32
R9-980506