Manual Bosch Appliances CC408
Manual Bosch Appliances CC408
Manual Bosch Appliances CC408
Operators Guide
EN Solution 880
This material is designed for use by tradespeople with This device is equipped with pulse dialling while the
expertise in the installation of this product. Persons Telecom standard is DTMF tone dialling. There is no
without appropriate expertise should seek assistance guarantee that Telecom lines will always continue to
before attempting installation. support pulse dialling.
While care was taken in the preparation of this Use of dialling, when this equipment is connected to
material, Bosch Security Systems Pty Ltd and its the same line as other equipment, may give rise to
representatives are not responsible to any person or bell noise and also cause a false answer condition.
entity for any loss or damage directly or indirectly Should such problems occur, the user should not
caused by information in, or any omission from, this contact the Telecom Faults Service.
material. This equipment is set up to carry out test calls at pre-
Bosch Security Systems Pty Ltd reserves the right to determined times. Such test calls interrupt any other
make changes to features and specifications of its calls that may be set up on the line at the same time.
products at any time without prior notification. The timing set for such test calls should be discussed
with the installer.
The timing set for test calls from this equipment may
be subject to drift. If this proves to be inconvenient
and your calls are interrupted, then the problem of
timing should be discussed with the equipment
installer. The matter should not be reported as a fault
to Telecom Faults Service.
This equipment shall not be set up to make automatic
calls to the Telecom 111 Emergency Service.
This equipment should not be used under any
circumstances that may constitute a nuisance to other
Telecom customers.
In the event of any problem with this device, the
systems battery, AC mains supply, and telephone line
should be disconnected. The user is to arrange with
the supplier of the device to make the necessary
repairs.
Should the matter be reported to Telecom as a wiring
fault and the fault proven to be due to this product, a
call-out charge will be incurred.
Tables
Table 1: Specifications ............................................. 5
Table 2: Zone Indicator........................................... 6
Table 3: AWAY Indicator....................................... 6
Table 4: STAY Indicator ......................................... 6
Table 5: MAINS Indicator ...................................... 7
Table 6: FAULT Indicator ...................................... 7
Table 7: Audible Indicators..................................... 7
Table 8: Arming Methods ....................................... 7
Table 9: Keyfob Audible/Visual Indications ......10
Table 10: Fault Condition Indicators .....................12
Table 11: Telco Arm/Disarm Dialling Digits........13
Table 12: Domestic Dialling Telephone Digits .....16
Table 13: Zone Status Display Descriptions..........18
Table 14: System Status ...........................................18
Table 15: Glossary of Terms ...................................20
1. Introduction 3. Features
Congratulations on selecting the Solution 880 Model The Solution 880 Control Panel uses the latest in
CC408 Control Panel to protect you and your microprocessor technology to provide you with more
property. To obtain the most from your unit, take the useful features and superior reliability and
time to read through this manual and familiarise performance. The main features of the control panel
yourself with the operating features of this system. In are listed below:
all aspects of planning, engineering, styling, x Eight programmable User Codes
operation, convenience, and adaptability, we have
sought to anticipate your every possible requirement. x STAY Mode and AWAY Mode operation
Programming simplicity and speed were some of the x Six programmable burglary zones
major considerations and we believe that our x Two programmable 24-hour zones
objectives in this area were more than satisfied.
x Siren and/or dialler lockout per zone
This guide explains all aspects of operating the
control panel. All system parameters and options are x Delayed reporting
detailed. Suitability is left up to the individual. Every x Built-in telephone fail monitor
system can be tailored to meet all requirements
x Day alarm
quickly and easily.
x Remote arming
2. Specifications x Answering machine bypass
x Event memory recall
Table 1: Specifications
x Upload/download programmable
o o x Auxiliary output (Output 2)
Temperature Range 0 C to +45 C
(+32 F to +113 oF)
o
x Relay output
Humidity 10% to 95% x Eight radio remote user codes
Power Source TF008 Plug Pack –
240 VAC/18 VAC @ 1.3 A x Entry and exit warning beeper
Stand-By Current 65 mA x EDMSAT – satellite siren compatible
Current Draw In 115 mA
x Separate fire alarm sound
Alarm Condition
Current Draw In 105 mA x Dual reporting
Alarm Condition
x Sensor watch
with Codepad
Back-Up Battery 6 Ah/12 VDC Rechargeable x Dynamic battery testing
sealed lead acid battery x Automatic arming/automatic disarming
Dimensions (case, 30.6 cm x 26.2 cm x 8.4 cm
packed in carton) (12.05 in. x 10.31 in. x 3.31 in.) x AC fail and system fault indicators
Weight 2.5 Kg (5.51 lb.) x Walk Test Mode
Supplier Code N771
x Monitored siren output (Output 1)
New Zealand PTC 211/98/083
Telepermit x Strobe output
Malaysia Approval Pending x Telco arm/disarm sequence (call forwarding)
Number
9. Alarms
9.1 Duress Alarm
A codepad duress alarm is used as a silent hold-up
3 alarm. This only occurs when the number 9 is added
to the end of any valid user code used to disarm the
system (for example, [2 5 8 0 9 #]). A duress alarm is
only useful if your system reports back to a
1 – Button 1: Arm or disarm in AWAY Mode monitoring station or pocket pager, because domestic
2 – Button 2: Arm or disarm STAY Mode reporting (such as a mobile phone) cannot decipher
3 – Buttons 1 and 2: Press both buttons at same which type of alarm occurred.
time to activate Panic alarm.
Figure 5: CP5 LED Codepad Showing Audible
Alarm Buttons
Figure 4: RE013/E – 4 Channel Keyfob
Transmitter
9.3 Fire Alarm 3. Press the [#] key after all selected zones are
isolated.
The horn speaker emits a distinct fire sound when
Two beeps sound and the system returns to the
both the [4] and [6] keys are pressed simultaneously.
disarmed state.
Contact your installer to disable the ability to activate
the codepad fire alarm or to silence the codepad fire 10.2 Code to Isolate
alarm. Only those user codes with the Code to Isolate
9.4 Medical Alarm priority level can isolate zones. If any user code has
this priority level, the standard isolating method (see
An audible alarm activates when both the [7] and [9] Section 10.1 Standard Isolating) does not function.
keys are pressed simultaneously. Contact your
installer to disable the ability to activate the codepad How to Isolate a Zone
medical alarm or to silence codepad medical alarm. 1. Press the [*] key followed by your user code and
the [*] key again to enter Isolating Mode (for
9.5 Tamper Alarm (Access Denied) example, [* 2 5 8 0 *]). Three beeps sound and
The tamper alarm restricts the number of times an the STAY indicator flashes.
invalid user code can be used in an attempt to 2. Enter the zone number (1 to 8), followed by the
operate the system. When the number of incorrect [*] key (for example, [1 *] = Zone 1, [2 *] =
code attempts equals the number programmed by Zone 2).
your installer, the system activates an alarm Each zone to isolate has a corresponding zone
condition. If reporting back to a security monitoring indicator that flashes. If you selected an incorrect
station, the system sends an Access Denied Report. zone to isolate, enter the incorrect zone number
To shutdown and lockout a codepad for a period of again followed by the [*] key.
time (0 to 150 seconds), ask your installer to program Repeat Step 2, if isolating more than one zone,
this feature. until all zones to isolate are selected.
3. Press the [#] key after all selected zones are
isolated.
10. Isolating Zones Two beeps sound and the system returns to the
Isolating zones allow you to manually disable one or disarmed state.
more zones before arming the system. Once a zone is
isolated, you can access that zone during the armed 11. Setting the Date and Time
state without activating an alarm.
Programming the date and time is only required
For example, you may need to isolate a zone because
when you need functions such as automatic test
before arming the system a PIR detector might
reports, automatic arming, and history events to
generate a false alarm, or you need to leave a pet
operate correctly.
inside a particular zone while away.
How to Program Date and Time
Isolating zones is performed by one of two methods.
Method two is optional and only allows those user 1. Enter your Master Code followed by the [6] and
codes programmed by your installer access to isolate [#] keys (for example, [2 5 8 0 6 #]).
zones. Three beeps sound and the STAY and AWAY
indicators flash.
10.1 Standard Isolating 2. Enter the day, month, year, hour, and minute
Standard Isolating allows all operators to isolate using the (DD, MM, YY, HH, MM) format (that
zones without knowing a valid user code. is, DD = day of the month, MM = month of the
year, YY = current year, HH = hour of the day,
How to Isolate a Zone
MM = minute of the day).
1. Press the [*] key twice to enter Isolating Mode.
Three beeps sound and the STAY indicator
When programming the hour of the day,
flashes.
you must use a 24-hour format.
2. Enter the zone number (1 to 8), followed by the
[*] key (for example, [1 *] = Zone 1, [2 *] = 3. Press the [#] key to exit and return to the
Zone 2). disarmed state.
Each zone to isolate has a corresponding zone Two beeps sound and the STAY and AWAY
indicator that flashes. If you selected an incorrect indicators go dark. If a long beep sounds, an
zone to isolate, enter the incorrect zone number error was made when entering the date and time.
again followed by the [*] key.
Repeat Step 2 if you are isolating more than one
zone, until all zones to isolate are selected.
Mains Indicator
22. Partitioning This indicator displays the status of the AC mains
supply. The indicator lights steadily when the AC is
You can partition or split the Solution 880 Control
normal and flashes when there is an AC supply
Panel into two individual areas. You can operate
failure.
both areas from one Master Partitioned codepad or
from separate area addressable codepads. Fault Indicator
22.1 Master Partitioned Codepad This indicator displays the status of the system’s fault
register. If the FAULT indicator flashes when the
Indicators
system detects a fault that has not yet been
Figure 6: Master Partitioned Codepad acknowledged. If the indicator lights steadily, the fault
has been acknowledged.
Partial Indicator
This indicator shows whether an area is armed in
STAY Mode 1. If the PARTIAL indicator is lit, the
area is armed in STAY Mode 1. If the indicator is
not lit, no areas are armed in STAY Mode 1. When
isolating zones, the PARTIAL indicator flashes to
indicate that you are in the isolate mode. The
PARTIAL indicator also flashes in conjunction with
the AUX indicator to indicate successful entry into
any programming mode (for example, when using
Master Code functions).
22.2 Operating From A Master
The indicators on a Master Partitioned codepad are Partitioned Codepad
configured into four groups. The following If you have a partitioned system with a Master
paragraphs describe the indicators. Partitioned codepad installed, operating procedures
described throughout this guide are the same with
22.1.1 Zone Indicators
one exception. All operations are relative to the area
The zone indicators (1 to 8) display the status of each whose AREA DISPLAY indicator is illuminated at
zone. These zones belong to the area whose AREA the time.
DISPLAY indicator is lit. If a ZONE indicator is lit,
that zone is unsealed. If a ZONE indicator is not lit, Example
that zone is sealed. When the AREA DISPLAY indicator number 2 is lit,
all operations performed affect only Area 2. To
22.1.2 Area On/Off Indicators
perform operations in another area, you must move
The group of four AREA ON/OFF DISPLAY the AREA DISPLAY illuminator to the desired area.
indicators show the status of each area. If an
indicator is lit, that area is armed. If the indicator is To Move From One Area To The Next
not lit, that area is disarmed. Press the AWAY button.
The area display indicator moves to the next area.
22.1.3 Area Display Indicators
Repeat until the desired indicator is lit.
A group of four AREA DISPLAY indicators
determine the area to which the displayed zones 22.3 Operating From Area Addressable
belong. Codepads
22.1.4 Status Indicators If you have a partitioned system with Area Addressable
This group of four indicators shows the following: codepads, the operating procedures described throughout
this guide are the same. Refer to 16. Codepad ID/Buzzer
AUX Indicator Tone Change on page 14 to determine the area to which a
The AUX indicator displays when the system is using particular codepad belongs.
the telephone line to communicate to the receiving
party.
The AUX indicator flashes in conjunction with the
PARTIAL indicator to show successful entry into any
programming mode. For example, this occurs when
you are using Master Code functions.
1 3
1 2 3 4 5 6 7 8
Term Description
24-Hour Zones A monitored input programmed to trigger an alarm condition when violated when
the system is armed or disarmed 24 hours a day.
Alarm Condition Your alarm system is armed and one of the detection devices is violated. A 24-hour
zone (such as a smoke detector) can activate an alarm condition when your system
arms or disarms.
Answering Machine Answering machine bypass is incorporated. You can connect to the system for
Bypass remote arming operations when there is an answering machine or facsimile machine
on the same telephone line.
Armed The system is in a ready state to accept alarms.
Automatic Arming The system automatically arms at the same time every day in AWAY Mode or STAY
Mode 1.
Automatic Disarming The system automatically disarms at the same time every day.
AWAY Mode Used to arm your system when you leave your premises.
Codepad Arm/disarm the system and carry out other functions such as adding and deleting
system user codes.
Day Alarm Monitor a combination of zones while the system is disarmed.
Detectors Devices connected to your alarm system used to detect intrusion and cause an
alarm condition. Some forms of detection devices include Passive Infrared (PIR),
smoke detectors, photoelectric beams, reed switches, and vibration sensors.
Disarmed A state that does not accept alarms except on zones programmed for 24-hour
operation.
Dynamic Battery Used to monitor and test the condition of your back-up battery.
Testing
Entry Time/ The time allowed by a zone for disarming the system after entering your premises.
Entry Delay
External Equipment Any device connected to your system such as detectors, codepads, and sirens.
Forced Arming A situation where your alarm system can be armed when one or more zones are
unsealed.
Handover Delay The system is armed and a zone programmed for delay was violated. The delay zone
hands over the remaining delay time to a zone programmed as handover. The
handover zone does not activate an alarm until the remaining delay time expires. A
handover zone acts as an instant zone if violated before the delay zone.
Hand Held Remote Used to remotely operate your system by hand held transmitters.
Control
Isolating Manually disable (isolate) one or more zones before arming the system.
Master Code A numeric code used to arm and disarm the system and to allow access to
functions such as adding and deleting user codes.
Monitoring Station A secure location where a digital receiver monitors numerous alarm systems and
deciphers their Alarm Transmission Reports. The operator can then advise the
appropriate authorities to take immediate action.
Panic Alarm Type of alarm that indicates to the monitoring station there is an emergency
situation at your premises.
Sealed Refers to zone status. If a zone is sealed, the detection device is not violated and
the zone indicator does not display on the codepad.
Sensor Watch The control panel can recognise that detection devices may have stopped working
or that the view to a PIR detector is blocked (unable to detect any movement over
the duration of the time programmed by your installer).
Term Description
Silent Alarm Your installer may program zones for silent operation. When the zone programmed
for silent operation is violated during the armed period, your alarm system
communicates with the monitoring station without sounding the sirens.
STAY Mode 1 A condition that automatically isolates zones when your system is armed in STAY
Mode 1. Only your installer can program zones to be isolated automatically in STAY
Mode 1.
STAY Mode 2 A condition that automatically isolates zones when your system is armed in STAY
Mode 2. Only the Master Code holder can program zones to be isolated
automatically in STAY Mode 2.
Telco Arm Sequence Telco arming is a feature that automatically calls the telephone exchange and diverts
your telephone number to another telephone when the system is armed in AWAY
Mode. (In Australia, this feature is called “Call Forward”.)
Telco Disarm Telco disarming automatically calls the telephone exchange and does not forward
Sequence your telephone number.
Unsealed Refers to zone status. A zone is unsealed when a zone is violated. The
corresponding zone indicator displays on the codepad.
User Code The personal identification number that the operator uses to arm and disarm the
system.
Zones A monitored input used to trigger an alarm condition when violated.
Service Notes
Zone Description
Describe each zone and mark the zones that are programmed to be automatically isolated in STAY Mode 1
or are programmed for day alarm operation.
Isolated In Day Alarm
STAY Mode 1 Enabled
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
Entry/Exit Times
Entry Timer 1 Exit Time
Entry Timer 2 Entry Guard Time
Arming Options
Single Button Arming YES NO Forced Arming YES NO
Output Descriptions
Output 1 Output 3
Output 2 Output 4
Isolating Method
Standard Isolating YES NO
Communication Options
Back To Base Reporting YES NO
Can Your System Be Serviced By Another Technician YES NO If Yes, Installer’s Code
Index
24-Hour Zones 20
D
A Date and Time 12
AC Mains Fail 12 Day Alarm 15
Adding Radio User Codes 9 Deleting Radio User Codes 9
Adding User Codes 9 Deleting User Codes 9
Alarm Condition 20 Detectors 20
Alarms Disarmed 20
Duress .................................................................... 10 Disarming 9
Fire ......................................................................... 11 Domestic Dialling 16
Medical .................................................................. 11 Acknowledging Domestic Calls........................... 16
Panic....................................................................... 10 Disable.................................................................... 16
Tamper (Access Denied)...................................... 11 Programming Domestic Telephone Numbers ... 16
Answering Machine Bypass 20 Duress Alarm 10
Area Display Indicators 17 E
Area On/Off Indicators 17 E2 Fault 12
Armed 20 Entry Delay/Entry Time 20
Arming Entry Guard Timer 8
AWAY Mode .......................................................... 8 Event Memory Recall 15
STAY Mode 1 ......................................................... 8 External Equipment 20
STAY Mode 2 ......................................................... 8
F
Telephone Arming ............................................... 15
Fault Analysis 12
Audible Indications 7
Fault Description
Automatic Arming 20
AC Mains Fail ....................................................... 12
Automatic Disarming 20
AUX Indicator 17 Battery Fail............................................................. 12
AWAY Indicator 6 Communication Fail ............................................. 12
AWAY Mode 8, 20 Date and Time....................................................... 12
B E2 Fault .................................................................. 12
Battery Fail 12 Fuse Fail ................................................................. 12
Battery Testing 20 Horn Speaker Fail ................................................. 12
Bell Test 14 Sensor Watch Fail ................................................. 12
C Telephone Line Fail .............................................. 12
Fault Descriptions 12
Codepad 20
Communciation Fail ............................................. 12
Duress Alarm ........................................................ 10
System Fault........................................................... 12
Fire Alarm ............................................................. 11
FAULT Indicator 7, 17
Medical Alarm ...................................................... 11
Features 5
Panic Alarm........................................................... 10 Fire Alarm 11
Tamper Alarm....................................................... 11 Forced Arming 8, 20
Codepad Indicators Fuse Fail 12
Audible Indications ................................................ 7
H
AWAY Indicator .................................................... 6
Hand Held Remote Control 20
FAULT Indicator .................................................... 7 Handover Delay 20
MAINS Indicator.................................................... 6 Horn Speaker Fail 12
Off Indicator............................................................ 7 Horn Speaker Test 14
On Indicator............................................................ 7 I
STAY Indicator....................................................... 6 Isolating 20
System Disarmed .................................................... 6 Isolating Zones 11
Zone Indicators ....................................................... 6 Code to Isolate ...................................................... 11
Communciation Fail 12 Standard Isolating ................................................. 11
Communication Fail 12
M STAY Mode 1 8, 21
MAINS Indicator 6, 17 Entry Guard Timer ................................................. 8
Master Code 20 STAY Mode 2 8, 21
Master Partitioned Codepad Indicators 17 Entry Guard Timer ................................................. 8
Medical Alarm 11 Programming Zones................................................ 9
Monitoring Station 20 Strobe Indications 10
O Strobe Test 14
System Disarmed 6
Off Indicator 7
On Indicator 7 T
Operating From A Master Partitioned Codepad Tamper Alarm 11
17 Telco Arm Sequence 13, 21
Operating From Area Addressable Codepads Telco Disarm Sequence 21
17 Telephone Line Fail 12
P Test Report 14
Testing
Pager Reporting 18
Panic Alarm 10, 20 Bell Test.................................................................. 14
PARTIAL Indicator 17 Horn Speaker Test ................................................ 14
Partitioning 17 Strobe Test ............................................................. 14
Test Report ............................................................ 14
R
Walk Test ............................................................... 14
Radio User Codes
Adding ..................................................................... 9 U
Deleting.................................................................... 9 Unsealed 21
Remote Arming 15 User Codes 21
Remote Control 20 Adding...................................................................... 9
S Adding Radio Users................................................ 9
Sealed 20 Deleting .................................................................... 9
Sensor Watch 20 W
Sensor Watch Fail 12
Walk Test 14
Silent Alarm 21
Speaker Beeps 10 Z
Status Indicators 17 Zone Indicators 6, 17
STAY Indicator 6 Zones 21
Notes: