LEGEVO - 102 - User - Guide: Shenzhen Legevo Technology Co.,Ltd
LEGEVO - 102 - User - Guide: Shenzhen Legevo Technology Co.,Ltd
LEGEVO - 102 - User - Guide: Shenzhen Legevo Technology Co.,Ltd
LEGEVO_102_User_Guide
BRAND: VOLTTAK
MODEL: 102
USE: Equipo para rastreo satelital
MAIN FUNCTION : Radiomodem para transmision de datos con GPS
Table of Contents
Preface ..........................................................................................................2
Attention ...................................................................................................... 2
◆Set up .....................................................................................................3
◆Application ...........................................................................................12
◆Specs. ...................................................................................................12
FAQ..............................................................................................14--16
1
Shenzhen Legevo Technology Co.,Ltd.
Preface
Thank you for purchasing our products. This deliberately edited manual is to
introduce the tracker with the complete technical data and the instructions showing
how to operate the device smoothly and correctly. Make sure to read this manual
carefully before using this product. Most problems could be solved through the
explanations and the troubleshooting tips. Once you finish reading it, keep it handy for
necessary reference. Please note that specification and information are subject to
changes without prior notice in this manual. Any change will be integrated in the latest
release. The manufacturer assumes no responsibility for any errors or omissions in this
document.
Attention
1. Make sure to read this manual carefully before using this product.
2. Please insert the SIM card before installing, and make sure the SIM card has no
password, otherwise the tracker will not work normally.
3. Please make sure that all the cables of the tracker has been connected rightly, and
then connect the tracker to host power. Must not install or take down the tracker
when it is power on. If you found any troubles or omissions about the connections of
cables, please cut off power first, otherwise you will easily damage the tracker.
4. The tracker works in wireless communications, so please cut off the host power
before your vehicles entering fuel depot and dangerous material place.
5. The tracker’s work voltage is 9V-28V. Please use the tracker in the scope of work
voltage.
6. The host of GPS tracker is a low-power wireless transmitter and receiver. It receives
and sends radio frequency signal when it is working.
7. To avoid electromagnetic interference or uncompatible configuration, please stop
using your tracker in the noticed place.
2
Shenzhen Legevo Technology Co.,Ltd.
◆Main functions
1. Positioning and Tracking: Through the on-line Positioning Platform or the cell phone to
locates at times, and get the working status. You can choose the Positioning Platform by
yourself.
2. Remote controlling oil and circuit: you can control the car oil and circuit via the unit by
SMS in anywhere and anytime.
3. Overspeed Alert: Send SMS to the unit to start over speed alert function. When the
vehicle is overspeed, the unit will send the overspeed alert to all authorized numbers.
4. Geo-fence: Set up a geo-fence for the unit to restrict its movements within a district.
The unit will send the message to all authorized numbers when it breaches the district.
5. Auto Track: You can set up auto track by SMS or on-line positioning platform.
6. Mileage statistics; ACC checking; cutting off power .
◆Set up
1.Initialization
Send “begin + password” in SMS to the unit, it will reply “begin ok” and initialize all the
settings. (Default password: 123456)
3
Shenzhen Legevo Technology Co.,Ltd.
5. Control Circuit
Send SMS “stopelec+password” to control circuit. For example send SMS:
“stopelec123456”.
"stopoil" as instructions, "123456" as the password.
To supply the circuit again, send SMS “supplyelec+password” to the unit. For example,
send SMS “Supplyelec123456” to the tracker. "Supplyelec" as instruction, "123456" as
password.
6. Overspeed alert
Set up: Send SMS “speed+password+space+080” to the unit (support the speed is
80km/h).
For example, send SMS “speed123456 080”. "speed" as instruction, "80" as limit speed,
“123456”as password.
Cancel: Send SMS “nospeed+password” to deactivate the overspeed alert.
7. Geo-fence
Set up a geo-fence for the unit to restrict its movements within a district. The unit will
send the message to the authorized numbers when it breaches the district.
Set up: The user can Send SMS “stockade + password + space + MinLatitude,
MinLongitude; MaxLatitude, MaxLongitude” to unit to set the restricted district. In case
of breach, it will send SMS “stockade! + geo-info” to the authorized numbers.
For example send SMS “stockade123456 22.548123, 114.081234; 22.549123,
114.082234” to the unit.
Remark: The first latitude & longitude is coordinate of min of the Geo-fence, while the
second latitude & longitude is the coordinate of the max. It will alarm one time in each
setting.
Cancel: Send SMS “nostockade + password” to deactivate this function.
This function will be out of effect after the unit moves outside the district.
4
Shenzhen Legevo Technology Co.,Ltd.
In order to send GPS data to IP address, you still must set mobile network Access Point
Name (APN). If you don’t know the APN, you can consult local network service supplier.
The format of set APN is “APN + password +space + apn value”. For example you send
SMS “apn123456 cmnet” to the device. The device will reply SMS “Set APN ok.” .
format of set GPRS user name and password is “user + space + GPRS user name + space
+ GPRS password”. For example, “user name 123456”, “user” is command, “name” is
GPRS user name, “123456” is GPRS password. After send SMS, tracker will reply “Set
GPRS User and Password ok . ” .
6
Shenzhen Legevo Technology Co.,Ltd.
◆Hardware Installation
7
Shenzhen Legevo Technology Co.,Ltd.
8
Shenzhen Legevo Technology Co.,Ltd.
9
Shenzhen Legevo Technology Co.,Ltd.
② Power button
Press the power button 3 seconds , device on
Press the power button 3 seconds , device off
10
Shenzhen Legevo Technology Co.,Ltd.
3. Install relay
4. LED Indications
①Put the SIM card in place and installed the tracker in the car
②Make sure the power button ON
Put the SIM card in place and installed the tracker in the car, the green indicator is on.
The red indicator will on when the batter is charging.
GSM LED (Green)
On Device booting.
Flashing every 0.1 second Sending messages or data.
Flashing every 1 second Searching GSM signals.
Flashing every 2 second Has connected to the GSM network.
GPS LED (Blue)
Off Searching GPS signals.
On Has been located.
Flashing every 2 second GPS module is standby.
11
Shenzhen Legevo Technology Co.,Ltd.
◆Application
◆Specs.
Content Specs
Dim. 75* 23 * 12(mm)
Weight 80g
Green indicator showing the GSM signal
LED indicator
Blue indicator showing the GPS signal
Button/Switch 1 power button
12
Shenzhen Legevo Technology Co.,Ltd.
◆Command Set
Stockade123456 coordinate;
7 Geo fence alert coordinate Set stockade ok
Nostockade123456 Cancel stockade ok
8 Restart tracker Reboot123456 System will reboot
13
Shenzhen Legevo Technology Co.,Ltd.
27 Delete requestdeleteadmin
authorized
number
2. Accessories
14
Shenzhen Legevo Technology Co.,Ltd.
2 I/O cable
3 Adhensive tape
◆FAQ:
Part I: how to Activate the GPS Device?
1 By Legevo (recommend , convenient)
2 By yourself (by Mobile Phone SMS Commands ,email us for the SMS commands file )
3 By yourself ( by Legevo Tool Configuring Device Parameters ,complicated)
15
Shenzhen Legevo Technology Co.,Ltd.
◆Contact information:
Shenzhen Legevo Technology Co.,Ltd.
Tel:+8613265573535
Email:sales@legevo.com
Add:Rm 811-815, 523 building, Bagua 2nd Road, Futian Dist,Shen Zhen
16