Step 1: Preparing to Start Up Step 2: Connecting Devices Step 3: Powering up

WAN/LAN 1 WAN/LAN 1 WAN/LAN 1

1
2 2
MPA2 1 3

4
Quick Startup Guide 3
Access Control System MPA2 1
5

This document describes the basic setup, wiring, and configu-

ration steps for getting started with a MPA2 access control
panel.

Setup Process
Step 1. Preparing to Start Up 1. Power Up the Panel (13, 8 V PSU or PoE (+)).
4 4
Step 2. Connecting Devices 2 2. Check Power LEDs on Mains/on PoE.
Step 3. Powering Up 3. Observe Power Up sequence (Heart Beat LED Green).
Step 4. Connecting to the Web Server 4. Test Reader(s) (OSDP/Wiegand).
Step 5. "Logging In" to the System 1. Select/Check the power PSU 13, 8 V DC or PoE(+). 1. Check the Input/Output devices (Door Status / Door Con-
tact) connections (P10/P18 or RJ45). 5. Test Input devices (Door Status / Door Contact).
Step 6. Configuring the System 2. Select/Check the Host connection IP (Ethernet) or USB.
3. Check DIP-Switch default status. (DIP Switch 3 and 9 are 2. Check/Select the your Reader connections (OSDP/Wiegand
ON). - RJ45).
For default IP, Ethernet host connection (LAN/WAN1), set
Note: a. For OSDP readers Dip Switch 1 & 10 are ON.
DIP-Switch 4 to ‘ON’. (See Step 5:2)
b. For Wiegand readers Dip Switch 1 & 10 are OFF.
Doc: 800-25470 4. Check the Relay configuration.
06/2019

Step 4: Connecting to the Web Server Step 5: “Logging In” to the System 3. Click Advanced. A detailed message about the connection is 4. Click Proceed to 192.168.1.150. The Sign In page is
displayed. displayed.
Note: These steps are for computers with Windows 7 operating 1. Launch the Internet browser.
system or higher. The steps for other operating systems
might be slightly different. Note: Honeywell recommends Google Chrome™.
2. Enter the panel’s IP address in the address box.
• IP/Ethernet > https://192.168.1.150 (DIP-Switch 4 to ‘ON’
1. Click Start > Control Panel.
Position) or USB > https://192.168.2.150 (fixed)
2. Click Network and Sharing Center. A message warns that the connection is not private. a
3. Click Change adapter settings.
4. Identify your local Ethernet connection (Local Area b
Connection) and double-click on the link.
5. Click Properties.
6. Highlight the Internet Protocol (TCP/IPv4).
7. Click Properties. View your system’s current IP properties. a. Enter admin in both Username and Password fields.
8. Select Use the following IP address. b. Change the Password for better security.

9. Enter 192.168.1.10 in the IP address field.

10. Enter 255.255.255.0 in the Subnet Mask field.
11. Click OK; OK; Close
3. Click SIGN IN. The MPA2 Dashboard appears. Step 6: Configuring the System Step 6.2: Set the Time Step 6.3: Create Schedules
1. Set the Communication
2. Set the Time
3. Create Schedules
4. Configure Spaces and Doors
5. Add People and Cards
6. Create Access Groups

Step 6.1: Set the Communication

Note: EVL mode is preferred. If you switch to EVL mode, the
panel automatically reboots.

Step 6.4: Configure Spaces and Doors Step 6.5: Adding People and Cards Step 6.6: Creating Access Groups Technical Support
Hours of Operation | Monday through Friday, 9:00 am – 7:00 pm EST
Phone Support | 1.800.323.4576 Technical Support, Option 2
MyWebTech Customer Portal | https://mywebtech.honeywell.com
E-mail Support | https://www.honeywellsystems.com/ss/techsupp/
index.html
Schedule Support | https://www.honeywellsystems.com/ss/
scheduleSupport/index.html
Online Training | www.HoneywellDiscoverTraining.com

www.honeywellaccess.com
1 800 323 4576 Option 2 (North America only)
https://mytechweb.honeywell.com | Document 800-25470 - Apr 2019
Honeywell Access Systems | 2700 Blankenbaker Pkwy. Suite 150, Louis-
ville, KY 40299
© 2019 Honeywell International. All rights reserved.

Scan the below QR Code for Disclaimer Information.