Flowcrete Asia Deckshield Ed Rapide May2020 Tds
Flowcrete Asia Deckshield Ed Rapide May2020 Tds
Flowcrete Asia Deckshield Ed Rapide May2020 Tds
Fast Cure:
Dramatically reduces installations
Technical Profile*
times due to a fast cure formulation. FIRE RESISTANCE
EN 13501-1 Cfl - s1
Attractive:
SLIP RESISTANCE**
Brightens up dull, dark, musty car parks
Method described in Dry>40, Wet depends on
and suspended floors. BS 7976-2 (typical values specification (in accordance with
for 4-S rubber slider) HSE and UKSRG guidelines)
UV Resistant: CHEMICAL RESISTANCE
100% UV light stable and does not Contact Technical Department. Resistant to petrol, diesel, antifreeze,
yellow over time. hydraulic fluid, chlorides and battery acids.
slips and trips for car park users. RESISTANCE TO CHLORIDE IONS
DOT BD47/94: Appendix B, No chloride ion
Hard Wearing: Method B4,2(d). penetration after 28 days
Protects substrates against the CRACK BRIDGING
demands of heavy multi-flow traffic. BS EN 1062-7 Method A, Table 6 Class A3 (-20°C)
BOND STRENGTH
Greater than cohesive strength of 25 N/mm2 concrete. >1.5 MPa
SPEED OF CURE
Light Traffic 1h
* These figures are typical properties achieved in laboratory tests at 20°C and at
50% Relative Humidity.
www.flowcreteasia.com
Model Specification Substrate Requirements
System Deckshield ED Rapide Concrete or screed substrate should be a minimum
Finish Textured of 25 N/mm2, free from laitance, dust and other
Thickness Dependant on specification contamination. Substrate should be dry to 95% RH
as per BS8204. The system is designed to cope with
Manufacturer Flowcrete Asia
construction moisture but is not designed to resist
Preparatory work and application in accordance hydrostatic water pressure. In such circumstances
with manufacturer’s instructions. external tanking or pressure relief, by e.g. directed
drainage, must be provided to the structure. Should
System Design Deckshield Oxide
Deckshield Scatter Deckshield Rapide not be applied if there is an existing sub-slab DPM.
Rapide Topcoat Bodycoat
Deckshield
Rapide Topcoat
Installation Service
The installation should be carried out by a licensed
contractor with a documented quality assurance
scheme. For details of our licensed contractors,
contact our customer service team or enquire via
our website at www.flowcreteasia.com
Environmental Considerations
Deckshield Rapide The finished system is assessed as non-hazardous
Membrane
Prepared to health and the environment. The long service
Flowfast Natural Quartz
Substrate
Damp Primer 0.4 - 0.8mm Scatter life and seamless surface reduce the need for
repairs, maintenance and cleaning. Environmental
Products Included In This System
and health considerations are controlled during
Primer Flowfast Damp Primer
manufacture and application of the products by
Sand Scatter Silica Quartz Scatter 0.4 - 0.8mm Flowcrete staff and fully trained and experienced
Membrane Deckshield Rapide Membrane contractors.
Basecoat Deckshield Rapide Bodycoat
Sand Scatter Deckshield Oxide 0.7 - 1.2mm
Important Note
Flowcrete products are guaranteed against
Finishing Coat Deckshield Rapide Topcoat
defective materials and manufacture and are
Note 1: Alternative specifications are available for sold subject to our standard ‘Warranty, Terms
steep ramps and ramps with severe camber. and Conditions of Sale’, copies of which can be
Note 2: The type of resin used and catalyst obtained on request. Warranty does not cover
dosage are temperature dependant. Please consult suitability, fit for purpose or any consequential or
Flowcrete for further advice. related damages.
Note 3: Technical proposals are specifically written No resin system is totally colour fast and may
for each installation which may require substrate change colour over time (exhibits a yellowing
details and site survey report. effect). Colour change depends on the UV light and
heat levels present and hence the rate of change
Detailed application instructions are available upon cannot be predicted. This is more noticeable in very
request. light colours but does not compromise the product’s
Aftercare, Cleaning & Maintenance physical or chemical resistance characteristics. We
Clean regularly using a single or double headed have endeavoured to adopt colours within our
rotary scrubber drier in conjunction with a mildly standard range which minimise this change.
[29/05/20]
alkaline detergent.
1. Light colours may require additional coats to achieve desired results 2. It is recommended that top coat colours are close to base coats colours to achieve desired results
3. This product is not UV stable and may discolour unless otherwise stated 4. System Data Sheet to be read in conjunction with Method Statement and Product data Sheets.
www.flowcreteasia.com