07 GB PDF
07 GB PDF
07 GB PDF
TOOLS
HOW TO CHOOSE
SCREWDRIVER
Slotted - Ideal Phillips & Pozi - ideal for general joinery and
for traditional cabinet construction. Phillips and Pozi are popular in all forms
making. For quality of joinery and construction, and are now used universally
craftsmanship slotted and referred to by their point size, 1,2, 3 or 4 PT.
screws still look The geometry of the screw recesses is different so avoid
the most attractive, ‘making do’ with the ‘wrong’ screwdriver. The driving
particularly when the faces of the Phillips screw all taper down to the tip,
slots line up pertectly. whereas with Pozi they are parallel which is designed
Slotted screwdrivers to reduce ‘Cam Out’, the point when the screwdriver lifts
are made with flared out of the recess damaging the screw.
tips and parallel tips. For most work select a flared tip
Torx - ideal for maintenance and service engineers.
screwdriver, but you should select a parallel tip that
This is the strongest and most wear resistant screw type
is the same width as the screw slot, if you need to
most commonly found in machinery, cars and domestic
drive the screw below the surface of the wood without
appliances. Torx are available in 6 sizes.
damage. Select a tip that matches the width of the screw
slot, too wide and it will damage the work, too narrow
and it may damage the screw slot.
Handle moulded direct to bar Soft grip handle Smooth domed end
virtually unbreakable bond. – perfect combination for fast spinning action
Highly reliable and providing of great grip plus – speed and comfort
an extra long life reduces fatigue
Large diameter
handle
Chrome vanadium offers great torque Colour coded ends
steel bar allows needed for easy identification
for high torque and reduces for driving wood of the “right” screwdriver
the chance of tip breakage screws for each screw type
FatMax® PARALLEL
7
0-64-983 parallel 3,5 x 75 mm X 6 3253560649838 1-64-983 parallel 3,5 x 75 mm - 6 3253561649837
0-64-984 parallel 3,5 x 100 mm X 6 3253560649845 1-64-984 parallel 3,5 x 100 mm - 6 3253561649844
0-65-017 parallel 4 x 100 mm X 6 3253560650179 1-65-017 parallel 4 x 100 mm - 6 3253561650178
0-65-093 parallel 4 x 150 mm X 6 3253560650933 1-65-093 parallel 4 x 150 mm - 6 3253561650932
0-65-476 parallel 5,5 x 125 mm X 6 3253560654764 1-65-476 parallel 5,5 x 125 mm - 6 3253561654763
0-65-094 parallel 5,5 x 150 mm X 6 3253560650940 1-65-094 parallel 5,5 x 150 mm - 6 3253561650949
0-65-096 parallel 6,5 x 150 mm X 6 3253560650964 1-65-096 parallel 6,5 x 150 mm - 6 3253561650963
0-65-097 parallel 6,5 x 200 mm X 6 3253560650971 1-65-097 parallel 6,5 x 200 mm - 6 3253561650970
0-65-319 Pz 0 x 75 mm X 6 3253560653194
0-65-335 Pz 1 x 100 mm X 6 3253560653354
0-65-336 Pz 1 x 250 mm X 6 3253560653361
0-65-337 Pz 2 x 125 mm X 6 3253560653378
0-62-571 Pz 2 x 250 mm X 6 3253560625719
0-65-338 Pz 3 x 150 mm X 6 3253560653385
0-65-339 Pz 4 x 200 mm X 6 3253560653392
1-65-319 Pz 0 x 75 mm - 6 3253561653193
1-65-335 Pz 1 x 100 mm - 6 3253561653353
1-65-336 Pz 1 x 250 mm - 6 3253561653360
1-65-337 Pz 2 x 125 mm - 6 3253561653377
1-62-571 Pz 2 x 250 mm - 6 3253561625718
1-65-338 Pz 3 x 150 mm - 6 3253561653384
1-65-339 Pz 4 x 200 mm - 6 3253561653391
0-65-408 Pz 1 x 30 mm X 6 3253560654085
0-65-409 Pz 2 x 30 mm X 6 3253560654092
1-65-408 Pz 1 x 30 mm - 6 3253561654084
1-65-409 Pz 2 x 30 mm - 6 3253561654091
FatMax® PHILLIPS
0-65-204 Ph 00 x 50 mm X 6 3253560652043
0-65-206 Ph 0 x 75 mm X 6 3253560652067
0-65-207 Ph 1 x 100 mm X 6 3253560652074
0-65-208 Ph 1 x 250 mm X 6 3253560652081
0-65-209 Ph 2 x 125 mm X 6 3253560652098
0-65-224 Ph 2 x 250 mm X 6 3253560652241
0-65-316 Ph 3 x 150 mm X 6 3253560653163
0-65-317 Ph 4 x 200 mm X 6 3253560653170
1-65-204 Ph 00 x 50 mm - 6 3253561652042
1-65-206 Ph 0 x 75 mm - 6 3253561652066
1-65-207 Ph 1 x 100 mm - 6 3253561652073
1-65-208 Ph 1 x 250 mm - 6 3253561652080
1-65-209 Ph 2 x 125 mm - 6 3253561652097
1-65-224 Ph 2 x 250 mm - 6 3253561652240
1-65-316 Ph 3 x 150 mm - 6 3253561653162
1-65-317 Ph 4 x 200 mm - 6 3253561653179
7
0-65-406 Ph 1 x 30 mm X 6 3253560654061
0-65-407 Ph 2 x 30 mm X 6 3253560654078
1-65-406 Ph 1 x 30 mm - 6 3253561654060
1-65-407 Ph 2 x 30 mm - 6 3253561654077
• 0-65-436 Parallel 3.5mm x 75mm, 5.5mm x 150mm. Flared 8mm x 150mm. Philips
PH1 x 100mm, PH2 x 125mm
• 0-65-440 Parallel 3.5mm x 75mm, 4mm x 100mm, 5.5mm x 125mm. Philips
PH1 x 100mm, PH2 x 125mm
• FatMax® 8piece Set: Parallel 3.5mm x 75mm, 5.5mm x 125mm, Flared 4mm x 100mm,
6.5mm x 150mm, 8mm x 150mm, Philips PH0 x 75mm, PH1 x 100mm, PH2 x 125mm
• 0-65-427 10 piece FatMax® Parallel Flared/Pozi Set: Parallel 3mm x 100mm, 4mm x
100mm, 5.5mm x 150mm, Flared 4mm x 100mm, 6.5mm x 30mm, 8mm x 150mm, Pozi
PZ0 x 75mm, PZ1 x 30mm, PZ1 x 100mm, PZ2 x 125mm
• 0-65-439 FatMax® 10piece Parallel Flared Phillips Set: Parallel 3mm x 50mm, 4mm x
100mm, Flared 5.5mm x 100mm, 6.5mm x 150mm, 8mm x 150mm, Philips PH00 x 50mm,
PH0 x 75mm, PH1 x 100mm, PH2 x 125mm, Voltage Tester
• FatMax® 12piece Set: Parallel 2.5mm x 50mm, 4mm x 100mm, 5.5mm x 150mm, Flared
5.5mm x 100mm, 6.5mm x 30mm, 8mm x 150mm, Philips PH0 x 75mm, PH1 x 100mm,
PH2 x 125mm, Pozi PZ0 x 75mm, PZ1 x 100mm, PZ2 x 125mm
• 9piece FatMax XL Set (Parallel 3mm x 75mm, 4mm x 100mm, 5.5mm x 150mm. Flared
7 4mm x 100mm, 8mm x 175mm, 6.5mm x 30mm. Pozi PZ0 X 60mm, PZ1 x 80mm, PZ2 x
100mm)
0-65-414 Ph 0 x 75 mm X 6 3253560654146
0-65-415 Ph 1 x 100 mm X 6 3253560654153
0-65-416 Ph 2 x 125 mm X 6 3253560654160
1-65-414 Ph 0 x 75 mm - 6 3253561654145
1-65-415 Ph 1 x 100 mm - 6 3253561654152
1-65-416 Ph 2 x 125 mm - 6 3253561654169
0-65-417 Pz 0 x 75 mm X 6 3253560654177
0-65-418 Pz 1 x 100 mm X 6 3253560654184
0-65-419 Pz 2 x 125 mm X 6 3253560654191
1-65-417 Pz 0 x 75 mm - 6 3253561654176
1-65-418 Pz 1 x 100 mm - 6 3253561654183
1-65-419 Pz 2 x 125 mm - 6 3253561654190
• 0- 65-441FatMax® 6piece Insulated Slotted Phillips Set: Slotted 2.5mm x 50mm, 3.5mm x
75mm, 5.5mm x 150mm, Philips PH1 x 100mm, PH2 x 125mm, Voltage Tester
• 0-65-443 FatMax® 6piece Insulated Screwdriver Set Slotted / Pozi: Slotted 2.5mm x 50mm,
7
3.5mm x 75mm, 5.5mm x 150mm, Pozi PZ1 x 100mm, PZ2 x 125mm, Voltage Tester
• Slotted 2.5mm x 50mm, 3.5mm x 75mm, 5.5mm x 150mm, Philips PH0 x 75mm, PH1 x
100mm, PH2 x 125mm, Pozi PZ0 x 75mm, PZ1 x 100mm, PZ2 x 125, Voltage Tester
CushionGrip PARALLEL
CushionGrip PHILLIPS
1-64-932 Ph 1 x 75 mm - 6 3253561649325
0-64-933 Ph 1 x 150 mm X 6 3253560649333
7
0-64-934 Ph 2 x 45 mm X 6 3253560649340
0-64-930 Ph 0 x 60 mm (precise) X 6 3253560649302 0-64-940 Ph 2 x 100 mm X 6 3253560649401
1-64-930 Ph 0 x 60 mm (precise) - 6 3253561649301 1-64-940 Ph 2 x 100 mm - 6 3253561649400
0-64-931 Ph 1 x 45 mm X 6 3253560649319 0-64-941 Ph 2 x 150 mm X 6 3253560649418
0-64-932 Ph 1 x 75 mm X 6 3253560649326 0-64-949 Ph 3 x 150 mm X 6 3253560649494
CushionGrip POZIDRIV
0-64-955 Pz 1 x 75 mm X 6 3253560649555
1-64-955 Pz 1 x 75 mm - 6 3253561649554
1-64-956 Pz 2 x 45 mm - 6 3253561649561
0-64-976 Pz 3 x 150 mm X 6 3253560649760
0-64-952 Pz 0 x 60 mm (precise) X 6 3253560649524
0-64-974 Pz 2 x 100 mm X 6 3253560649746
1-64-952 Pz 0 x 60 mm (precise) - 6 3253561649523
1-64-974 Pz 2x100 mm - 6 3253561649745
• 0-65-007 6piece CushionGrip Screwdriver Set (Slotted / Phillips): Parallel 5mm x 100mm.
Flared Instrument 3mm x 75mm, 5mm x 100mm, 6.5 x 150mm, Phillips PH1 x 100mm,
PH2 x 150mm
• 0-65-009 6piece CushionGrip Screwdriver Set (Philips): Flared Instrument 5mm x 100mm,
6.5 x 45mm, 6.5 x 150mm, Phillips PH1 x 75mm, PH2 x 45mm, PH2 x 150mm, Voltage
Tester
• 2-65-005 10piece Cushion Grip Blister set: Flared Instrument 3mm x 75mm,
5 mm x 100mm, 6.5mm x 45mm, 6.5mm x 150mm, 8mm x 150mm, Phillips Instrument
PH0 x 60mm, PH1 x 75mm, PH2 x 45mm, PH2 x 100mm, PH3 x 150mm
• 2-65-014 10piece Cushion Grip Pozi/Parallel Screwdriver Set: Flared Instrument
3mm x 75 mm, 5mm x 100mm, 6.5mm x 45mm, 6.5mm x 150mm, 8mm x 150mm,
Pozi Instrument PZ0 x 60mm, PZ1 x 75m, PZ2 x 45mm, PZ2 x 100mm, PZ3 x 150mm
• 4piece Cushion Grip Handy Computer Tool Set: Flared Instrument 3mm x 125mm,
3mm x 150mm, Phillips Instrument PH1 x 125mm, PH2 x 150mm, Pliers Slim Diagonal
Cutting, Slim Long Nose Pliers
• 40 tooth precision reversible ratchet with • Stanley FatMax XL logo hot stamped onto
lock-out. Three positions handle
• Injection molded bi-material handle • Removable bar with hex interface allowing
• Smooth contoured turning METAL end cap use of bar in power tools and hex drivers.
radius for hand palm comfort • Quick release Auto-Slim magnetic bit
• Ergonomic tri-lobular handle designed for holder
comfort and positive gripping • Selection of Chrome Vanadium (CrV)
• Handle over-moulded with ‘soft touch’ TPE, commonly used hexagon bits including
textured panels for extra power generation – Torx, Slotted, Pozidrive and Phillips
and comfort • Knurled blade, ideal for fast approaches.
• TPE marked with Stanley PIN number • Internal Bit Storage (6) for easy access
“69-19X”. to Bits without being separated from the
handle which will avoid loss
0-69-188 - x 24 3253560691882
7
9-69-188 - display 1 3253569691883
FatMax® MULTIBIT
• Large diameter handle offers great torque • Handle moulded direct to the bar virtually
needed for driving wood screws unbreakable bond. Highly reliable and
• Smooth doomed end for fast spinning providing an extra long life
action – speed and comfort • ¼” Bit Adaptor comes complete with most
• Chrome vanadium bar allows for high popular bit sizes – Phillips 1 and 2, Pozi 1
torque and reduces the chance of tip and 2, Slotted 4.5mm, 6mm
breakage
• Delivered with 10 1/4 hex tips • Patented bit storage for ease of visibility,
• Trefoil Tri lobular handle, bimaterial handle access and security
for torque and easy grip • Pawl mechanism with three positions
• Rust-proof chrome blade • Bearing ball system with spring mechanism
to facilitate access to the tips
7 0-66-357
0-66-358
7 pcs.
7 pcs.
X
X
3
3
3253560663575
3253560663582
• Handle over-moulded with ‘soft touch’ TPE, • Internal Bit Storage (6) for easy access
textured panels for extra power generation to Bits without being separated from the
and comfort handle which will avoid loss
• Removable bar with hex interface allowing • 69-191: long removable bar + 1 small
use of bar in power tools and hex drivers. removable bar + 15 bits including; Slotted
• Quick release Auto-Slim magnetic bit bit 3mm, 4.5mm, 6mm, PH1, PH2 x2, PH3,
0-69-192
holder. PZ1, PZ2 x2, PZ3, T10, T15, T20, T25
• Selection of 15 Chrome Vanadium (CrV) • 69-192: small removable bar + 15 bits,
commonly used hexagon bits including; slotted bit: 3mm, 4.5mm, 6mm,
• Knurled blade, ideal for fast approaches PH1, PH2 x2, PH3, PZ1, PZ2, x2, PZ3, T10,
(only 69-191) T15, T20, T25
0-69-191
0-69-191 15 pcs x 4 3253560691912
0-69-192 15 pcs x 4 3253560691929
7
• Pistol Grip Screwdriver Set (9Slot. 5.6, 6, 7, 8, 9, 10, 11mm)
7mm; Ph 1, 2, 3; Slot. 5, 6, 7; Ph. 0, 1, • In practical plastic case
2, 3 i 3 pt.; Torx T10, T15, T20, T25, T27, • Ratchet screwdriver with rotation control
T30; Hex tips: 2, 3, 4, 5, 5.5, 6mm; Square switch
tips: S1, S2, S3; extention; 6 pcs. Sockets:
• Supplied with Phillps 1 and 2, 2 x slotted, • Hex drive 6mm & 8 mm. Slotted 4.5mm
and 2 nut drivers (1/4 in and 5/16 in) & 6 mm. PH 1 & 2
• Ergonomically designed bi-material handle
for superb comfort
• Large diameter handle offers great torque • Soft grip handle – perfect combination
needed for driving wood screws of great grip plus reduces fatigue
• Colour coded ends make it easy to identify • Chrome vanadium steel bar allows for
the correct screwdriver for each screw type high torque and reduces the chance of tip
• Smooth domed end for fast spinning action breakage
– speed and comfort • Handle moulded direct to bar virtually
• Shot blasted tips ensure improved torque unbreakable bond. Highly reliable and
and corrosion protection providing an extra long life
0-65-491 5 X 75 mm x 6 xx
• 1/4’’ Drive bit slotted head - 39 mm • Conforms to ISO 1173 and DIN 3126
standards
• Conforms to ISO 1173 and DIN 3126 • 1/4’’ Drive Bit for Torx - 25 mm
standards
• Conforms to ISO 1173 and DIN 3126 • 1/4’’ Drive Bit for Tamper Proof Torx
standards - 25 mm
• Long reach provides access to recessed
fasteners
• Conforms to ISO 1173 and DIN 3126 • 1/4” Drive Slotted Head Bit - 25 mm
standards
7 1-13-652
1-17-768
1-13-654
1-13-655
3 x 25 mm
4 x 25 mm
5 x 25 mm
6 x 25 mm
X
X
X
X
6x1
6x1
6x1
6x1
3253561136528
3253561177682
3253561136542
3253561136559
1-13-656 7 x 25 mm X 6x1 3253561136566
1-13-657 8 x 25 mm X 6x1 3253561136573
1-13-658 10 x 25 mm X 6x1 3253561136580
1-68-992 Ph 2 x 50 mm - 10 x 1 3253561689925
1-68-926 Pz 2 x 50 mm X 10 x 1 3253561689260
3-68-804 Pz 2 x 70 mm - 10 x 1 3253563688049
3-68-807 Pz 2 x 100 mm - 10 x 1 3253563688070
• Drive Bit with groove for PH Head - 50 mm • Conforms to ISO 1173 and DIN 3126
standards
• Double mould square drive 1/4” blade • For general purpose use Precision
machined for perfect fit Forged and ground
for long life and durability
1-68-784 Ph 1 + 2 X 10 x 1 3253561687846
• Double mould square drive 1/4” blade • For general purpose use Precision
machined for perfect fit Forged and ground
for long life and durability
1-68-786 Pz 1 + 2 X 10 x 1 3253561687860
• 1/4’’ TORSION BIT for PZ head - 25 mm • Conforms to ISO 1173 and DIN 3126
standards
7
1-13-633 Pz3 X 6x1 3253561136337
• 1/4’’ Drive Torsion Bit for Ph Head • Conforms to ISO 1173 and DIN 3126
- 25 mm standards
1-13-678
1-13-679
1-13-680
T20
T25
T30
X
X
X
3x1
3x1
3x1
3253561136788
3253561136795
3253561136801
7
1-13-681 T35 X 3x1 3253561136818
1-13-682 T40 X 3x1 3253561136825
1-13-683 T45 X 3x1 3253561136832
1-13-684 T50 X 3x1 3253561136842
• 1/4” Extra Hard Torsion Drive Bit for Philips • Conforms to ISO 1173 and DIN 3126
Head (25mm) standards
• Very tough bits
• Conforms to ISO 1173 and DIN 3126 • 1/4’’ Extra Hard Torsion Bit for Pz Head
standards - 25 mm
• 1/4’’ Drive Titanium Bit With Groove for Ph • Conforms to ISO 1173 and DIN 3126
Head - 50 mm standards
• Tin coating
7
1-13-696 Ph3 x 6x1 3253561136962
1-13-643 7 x 65 mm - 1 3253561136436
1-13-644 8 x 65 mm - 1 3253561136443
1-13-645 9 x 65 mm - 1 3253561136450
1-13-646 10 x 65 mm - 1 3253561136467
1-13-649 L = 50 mm X 1 3253561136474
0-68-732 L = 60 mm X 1 3253560687328
1-68-732 L = 60 mm - 5x1 3253561687327
3-68-729 L = 75 mm - 5x1 3253563687295
7
1-13-648 L = 50 mm X 1 3253561136481
1-13-647 L = 50 mm X 1 3253561136474
BIT SET
• Bit Set + 1 Magnetic Bit Holder with Lock- • Slotted: 4-4.5-5.5mm. Phillips: PH1-PH2-
Ring PH3. Pozidriv: PZ1-PZ2-PZ3. Torx: T10-
T15-2xT20-2xT25-2xT27-2xT30-2xT40.
Tamperproof Torx: T10 -T15-T20-T25-T30.
Hexagonal: 3-4-5-6mm. Bit holder adaptor:
50mm
7
Lock-Ring PH1-PH2-PH3. Pozidriv: PZ1-PZ2-PZ3.
Hexagonal: 3-4-5-6mm. Torx: T8-T10-
T15-T20-T25-T27-T30-T40. Tamperproof
Torx: T10-T15-T20-T25-T27-T30-T40.
Magnetic bit holder: 60mm. 1/4” Square
drive socket. 1/4” Adaptor
• Bit Sets: 1 Magnetic Bit Holder with Lock- • Slotted: 4.5-5.5-6.5-8mm. Phillips:
Ring + 1 ratchet PH1-PH2-PH3. Pozidriv: PZ1-PZ2-PZ3.
Hexagonal: 3-4-5-6mm. Torx: T8-T10-
T15-T20-T25-T27-T30-T40. Tamperproof
Torx: T10-T15-T20-T25-T27-T30-T40.
1/4” Sockets: 6-7-8-10-11-12-13mm.
Magnetic bit holder: 60mm. 1/4” Mini
ratchet. 1/4” Adaptor
TECHNOLOGY
REDUCED HEAD PROFILE
30% smaller than the standard pawl
Bi-material Handle Available
in 1/4”, 3/8” and 1/2”
Complies with ISO standards 5° ARC SWING
5° With fine gearing
72-TOOTH PAWL
Maximum precision every time
MicroTough™ RATCHET
RATCHETS
• Ratchet - Pear Head - Bi-Material Handle • Conforms to ISO 3315 and DIN 3122
• 5° increments standards
• Matt chrome plated finish
7 1-13-848
1-13-708
3/8” – 210 mm
1/2” – 250 mm
-
-
10
5
3253561138485
3253561137082
• Round head ratchet for tight access area • Quick release push button provide extra
• Rotates left or right for direction Fully safety and handly operation
polished chrome plated finish for durability • Comfortable and durable moulded handle
and rust resistance withstands most industrial solvents
1-13-568 5 - 25 Nm - 1 3253561135682
1-13-565 10 - 50 Nm - 1 3253561135651
1-13-571 40 - 200 Nm - 1 3253561135712
1-13-572 1/2” 70 -> 350 Nm - 1 3253561135729
SLIDING TEE
EXTENSION BAR
EXTENTIONS
7
• Chrome vanadium steel standards
• Matt chrome plated finish
UNIVERSAL JOINT
7
1-17-264 1/2” – 68,5 mm - 10 3253561172649
COUPLER
7
through fastener flats instead of corners
1-13-830 7 mm - 10 3253561138300
1-13-831 8 mm - 10 3253561138317
1-13-832 9 mm - 10 3253561138324
1-13-833 10 mm - 10 3253561138331
1-13-834 11 mm - 10 3253561138348
1-13-835 12 mm - 10 3253561138355
1-13-836 13 mm - 10 3253561138362
1-13-837 14 mm - 10 3253561138379
1-13-838 15 mm - 10 3253561138386
1-13-839 16 mm - 10 3253561138393
1-13-840 17 mm - 10 3253561138409
1-13-841 18 mm - 10 3253561138416
1-13-842 19 mm - 10 3253561138423
1-13-843 20 mm - 10 3253561138430
1-13-844 21 mm - 10 3253561138447
1-13-845 22 mm - 10 3253561138454
1-13-846 23 mm - 10 3253561138461
1-13-847 24 mm - 10 3253561138478
1-17-293 4 mm - 10 3253561172939
1-17-294 5 mm - 10 3253561172946
1-17-295 5,5 mm - 10 3253561172953
1-17-296 6 mm - 10 3253561172960
1-17-297 7 mm - 10 3253561172977
1-17-298 8 mm - 10 3253561172984
1-17-299 9 mm - 10 3253561172991
1-17-350 10 mm - 10 3253561173509
1-17-351 11 mm - 10 3253561173516
1-17-352 12 mm - 10 3253561173523
1-17-353 13 mm - 10 3253561173530
1-17-354 14 mm - 10 3253561173547
1-13-751 4 mm - 10 3253561137518
1-13-752 5 mm - 10 3253561137525
1-13-753 5,5 mm - 10 3253561137532
1-13-754 6 mm - 10 3253561137549
1-13-755 7 mm - 10 3253561137556
1-13-756 8 mm - 10 3253561137563
1-13-757 9 mm - 10 3253561137570
1-13-758 10 mm - 10 3253561137587
1-13-759 11 mm - 10 3253561137594
1-13-760 12 mm - 10 3253561137600
1-13-761 13 mm - 10 3253561137617
1-13-762 14 mm - 10 3253561137624
7
• Chrome Vanadium sockets with ‘rubber’
insert to hold and protect spark plug from
accidental damage
4-88-993 16 mm X 10 3253564889933
4-88-996 21 mm X 10 3253564889964
1-17-094 16 mm - 10 3253561170942
1-17-095 17 mm - 10 3253561170959
1-17-096 18 mm - 10 3253561170966
1-17-097 19 mm - 10 3253561170973
1-17-098 20 mm - 10 3253561170980
1-17-099 21 mm - 10 3253561170997
1-17-250 22 mm - 10 3253561172502
1-17-086 8 mm - 10 3253561137099 1-17-251 23 mm - 10 3253561172519
1-17-087 9 mm - 10 3253561137129 1-17-252 24 mm - 10 3253561172526
1-17-088 10 mm - 10 3253561170881 1-17-253 26 mm - 1 3253561172533
1-17-089 11 mm - 10 3253561170898 1-17-254 27 mm - 1 3253561172540
1-17-090 12 mm - 10 3253561170904 1-17-255 28 mm - 1 3253561172557
1-17-091 13 mm - 10 3253561170911 1-17-256 29 mm - 1 3253561172564
1-17-092 14 mm - 10 3253561170928 1-17-257 30 mm - 1 3253561172571
1-17-093 15 mm - 10 3253561170935 1-17-258 32 mm - 1 3253561172588
1-17-265 12 mm - 10 3253561172656
1-17-266 13 mm - 10 3253561172663
1-17-267 14 mm - 10 3253561172670
1-17-268 15 mm - 10 3253561172687
1-17-269 16 mm - 10 3253561172694
1-17-270 17 mm - 10 3253561172700
1-17-271 18 mm - 10 3253561172717
1-17-272 19 mm - 10 3253561172724
1-17-273 21 mm - 5 3253561172731
1-17-274 22 mm - 5 3253561172748
1-17-275 24 mm - 5 3253561172755
1-17-276 27 mm - 5 3253561172762
1-17-277 30 mm - 5 3253561172779
1-17-061 18 mm - 10 3253561170614
1-17-062 19 mm - 10 3253561170621
1-17-063 20 mm - 10 3253561170638
1-17-051 8 mm - 10 3253561170515 1-17-064 21 mm - 10 3253561170645
1-17-052 9 mm - 10 3253561170522 1-17-065 22 mm - 10 3253561170652
1-17-053 10 mm - 10 3253561170539 1-17-066 23 mm - 10 3253561170669
1-17-054 11 mm - 10 3253561170546 1-17-067 24 mm - 10 3253561170676
1-17-055 12 mm - 10 3253561170553 1-17-068 26 mm - 5 3253561170683
1-17-056 13 mm - 10 3253561170560 1-17-069 27 mm - 5 3253561170690
1-17-057 14 mm - 10 3253561170577 1-17-070 28 mm - 5 3253561170706
1-17-058 15 mm - 10 3253561170584 1-17-071 29 mm - 5 3253561170713
1-17-059 16 mm - 10 3253561170591 1-17-072 30 mm - 5 3253561170720
1-17-060 17 mm - 10 3253561170607 1-17-073 32 mm - 5 3253561170737
1-17-280 14 mm - 10 3253561172809
1-17-281 15 mm - 10 3253561172816
1-17-282 16 mm - 10 3253561172823
1-17-283 17 mm - 10 3253561172830
1-17-284 18 mm - 10 3253561172847
1-17-285 19 mm - 10 3253561172854
1-17-286 21 mm - 5 3253561172861
1-17-287 22 mm - 5 3253561172878
1-17-288 23 mm - 5 3253561172885
1-17-289 24 mm - 5 3253561172892
1-17-290 27 mm - 5 3253561172908
1-17-278 12 mm - 10 3253561172786 1-17-291 30 mm - 5 3253561172915
1-17-279 13 mm - 10 3253561172793 1-17-292 32 mm - 5 3253561172922
• 12 point bi- hex recess with Maxi Drive • Conforms to ISO 2725 and DIN 3124
face profile to improve grip on fastener and standards
reduce risk of damage
4-88-789 17 mm X 20 3253564887892
4-88-790 18 mm X 20 3253564887908
4-88-791 19 mm X 20 3253564887915
4-88-792 20 mm X 10 3253564887922
4-86-541 9 mm X 20 3253564865418 4-88-793 21 mm X 10 3253564887939
4-86-542 10 mm X 20 3253564865425 4-88-794 22 mm X 10 3253564887946
4-86-543 11 mm X 20 3253564865432 4-88-795 23 mm X 10 3253564887953
4-86-544 12 mm X 20 3253564865449 4-88-796 24 mm X 10 3253564887960
4-86-545 13 mm X 20 3253564865456 4-88-797 25 mm X 10 3253564887977
4-86-546 14 mm X 20 3253564865463 4-88-798 26 mm X 10 3253564887984
4-86-547 15 mm X 20 3253564865470 4-88-803 32 mm X 10 3253564888035
• Cold Forged chrome vanadium steel • Deep sockets to enable access to fastener
sockets for strength and resistance to wear with a projecting threaded stud
• 12 point bi- hex recess with Maxi Drive • Conforms to ISO 2725 and DIN 3124
7
face profile to improve grip on fastener and standards
reduce risk of damage
1-86-418 10 mm - 6 3253561864186
1-86-420 12 mm - 6 3253561864209
1-86-421 13 mm - 6 3253561864216
1-86-422 14 mm - 6 3253561864223
1-86-423 15 mm - 6 3253561864230
1-86-424 16 mm - 6 3253561864247
1-86-425 17 mm - 6 3253561864254
1-86-426 18 mm - 6 3253561864261
1-86-427 19 mm - 6 3253561864278
1-86-429 21 mm - 4 3253561864292
1-86-430 22 mm - 4 3253561864308
1-86-432 24 mm - 4 3253561864322
1-86-435 27 mm - 4 3253561864353
1-86-438 30 mm - 2 3253561864384
1-86-439 32 mm - 2 3253561864391
• 9 Piece set: 3/8” Chrome Extendable • Handle design extends to 350mm: Locks
ratchet; Chrome Sockets: 8, 10, 11, 12, into five different lengths, locked & quick
13, 15, 17, 19mm release square drive
• Full ISO spec
• Available in 3/8” Square Drive
• 17 pcs. set: 11 x 1/4” standard hex • Fine tooth ratchet gives 5 degree angle
sockets: 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, of engagement -smoother operation
13mm; 1 x 1/4” drive Micro Tough ratchet • Fully polished chrome plated finish for
handle; 2 x Extension bars 150mm, durability and rust resistance
75mm; 1 x 1/4” Spinner handle; 1 x • DynaGrip bi-material handle for
Universal joint; 1 x adaptor 1/4”F X 3/8”M comfortable grip
• Micro Tough professional ratchet features
a quick release two way ratchet with a
20-30% smaller pear shaped head
• 15 pcs. set: 11 x 1/4” standard hex • Round head ratchet handle with quick
sockets: 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, release two way ratchet
14mm • Fully polished and chrome plated finish for
• 1 x 1/4” drive quick release ratchet handle durability and rust resistance
• 2 x Extension bars 150mm, 75mm • Comfortable and durable moulded handle
• 1 x Sliding T bar withstands most industrial solvents
• 21 psc. set: 10 1/4” standard hex sockets: • Round head ratchet handle with quick
4, 5, 6, 7, 8, 9, 10, 11, 12, 13mm; 1 release two way ratchet
1/4” drive quick release ratchet handle; • Fully polished chrome plated finish for
2 Extension bars 150mm, 75mm; 1 1/4” durability and rust resistance
Spinner handle; 1 1/4” hex bit adaptor; 3 • Comfortable and durable moulded handle
Phillips bits 1pt, 2pt, 3pt,; 3 Slotted bits 4, withstands most industrial solvents
5.5, 6.5mm
• 1/4” Sq drive ratchet; extension bar; x14 • Sockets have Premium Black Chrome
Bits; black sockets: 4, 5, 5.5, 6, 7, 8, 10, finish
11, 13mm • Strong corrosion resistance
• Comfortable bi-material handle • Laser etched markings for easy, clear
• Easy to lock the box identification
• Separate storage compartments for • Compact box with transparent lid
sockets and ratchet
7
• 30 Piece set: 1/4” black chrome • Separate storage compartments for
MicroTough ratchet; extention Bar 75, sockets and ratchet
150mm; T bar 125mm; bit holder; spinner • Sockets have Premium Black Chrome
handle; universal joint; x 10 bits; Black finish
chrome Sockets: 4, 4.5, 5, 5.5, 6, 7, 8, 9, • Strong corrosion resistance
10, 11, 12, 13, 14mm • Laser etched markings for easy, clear
• Comfortable bi-material handle identification
• Easy to lock the box
• 30 Piece set: 1/4” Round ratchet; spinner • Deep Chrome sockets: 5, 6, 7, 8, 9, 10,
handle; extention bar 75mm; universal 11, 12, 13mm
joint; bit holder; X6 Bits • Quick release and reverse switch
• Chrome sockets: 4, 5, 6, 7, 8, 9, 10, 11, • Comfortable handle
12, 13mm • Clam-shell case and closed box design
7
• 40 Piece set: 1/4” round ratchet; spinner • Quick release and reverse switch
handle; extention bar 75, 150mm; flex • Comfortable handle
extention 150mm; bit holder; X4 Bits; • Clam-shell case and closed box design
Bit sockets: Hex 4, 5, 6, Slotted 4, 5.5
Phillips® 1, 2, 3, Pozidriv® 1, 2, 3; L Hex
Key Set: 1.5, 2, 2.5, 3, 4, 5, 6mm; Chrome
sockets: 4, 5, 5.5, 6, 7, 8, 9, 10, 11, 12,
13mm
7
• 30 Piece set: 3/8” Round ratchet; extention • Deep Chrome sockets: 10, 12, 13, 14,
bar 75mm, universal joint; spark plug 18, 17mm
21mm; bit holder; x 6 Bits • Quick release and reverse switch
• Chrome sockets: 8, 9, 10, 11,12,13, 14, • Comfortable handle
16, 17, 18,19, 21, 22mm • Clam-shell case and closed box design
• 7 Hex sockets 6, 8, 10, 12, 14, 17, 19mm • Fully polished chrome plated finish for
• 1/2” Drive hex sockets durability and rust resistance
• 9 Torx sockets: T20, T25, T27, T30, T40, • Fully polished chrome plated finish for
T45, T50, T55, T60 durability and rust resistance
• 1/2” Drive Torx bit sockets
7
• 10 Impact sockets: 10-11-13-14-17-19-
21-22-23-24mm. 1 Extension: 125mm. 1
Dial. 2 Rings & 2 Pins
• 20 Piece set: 1/2” Round ratchet; extention • Quick release and reverse switch
bar 125mm; sliding T bar 250mm; • Comfortable handle
universal joint; spark plug 16, 21mm; • Clam-shell case and closed box design
Chrome sockets: 10, 11, 12, 13, 14, 15,
16, 17, 18, 19, 21, 22, 24, 27mm
• 26piece 1/2’’ Set & Combination Spanners • Fully polished chrome plated
(8, 10, 11, 12, 13, 14, 16, 17, 18, 19, • Comfortable and durable moulded handle
21, 22, 24 mm. 1 1/2” Ratel. 1 Extension withstands most industrial solvents
bar 125 mm. 1 Universal joint. 10
ringsteeksleutels: 8, 10, 11, 12, 13, 14,
15, 16, 17, 19 mm)
• 30 Piece set: 1/2” round ratchet; extention • Chrome sockets: 8, 9, 10, 11, 12, 13,
bar 125, 250mm; sliding T bar 250mm; 14, 15, 16, 17, 18, 19, 21, 22, 23, 24,
universal joint; spark plug 21mm; Bit 27, 30, 32mm
Socket: Hex 4, 5, 6, 8, 10 • Quick release and reverse switch
• Comfortable handle
• Clam-shell case and closed box design
7
1-94-670 72 pcs - 3 3253561946707
• 40 pcs. set: 11 x 1/4” Hex sockets: 4, 4.5, • Fully polished chrome plated finish
5, 5.5, 6, 7 ,8 ,9 ,10, 11, 13mm; 10 x • Comfortable and durable moulded handle
3/8”hex sockets: 10, 11, 12, 13, 14, 15, withstands most industrial solvents
17, 19, 22, 24mm; 1 x 3/8” Round head • Slim pattern Chrome Vanadium
QR Ratchet handle; 1/4” Spinner Handle; Combination Spanners
3/8”extension 150 mm; 3 way drive
adaptor; 3/8”F to 1/4”M; Universal joint;
hex bit adaptor; 3 x Slotted screwdriver
bits 4, 5.5, 7mm; Phillips bits No 1, No2,
No3; Pozidriv bits No1, No2, No3; 4 x Hex
wrenches: 1.5, 2, 2.5, 3mm; Round head
ratchet handle with quick release two way
ratchet
7
• 29-piece MicroTough™ 1/2’’’ Socket Set • Micro Tough professional ratchet features
(8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, a quick release two way ratchet with a 20-
19, 20, 21, 22, 23, 24, 26, 28, 29, 30, 32 30% smaller pear shaped head, smaller
mm. 1 1/2” Drive Micro Tough Professional than conventional 72 Fine tooth ratchet
ratchet handle. 3 Locking extension bars: gives 5 degree angle of engagement
75, 150 and 250 mm 1 Universal joint. 1 x • Fully polished chrome plated finish f or
1/2” to 3/8”) durability and rust resistance
• 12 point bi-hex sockets feature Maxi Drive
wall profile
• 50 Piece set: 1/4” & 1/2” Round ratchet; • Quick release and reverse switch
1/4” Spinner handle; 1/2” Extention bar • Comfortable handle
125mm; 1/4” Extention bar 75mm; 1/2” • Clam-shell case and closed box design
Sliding T bar 250mm; 1/4” Sliding T bar
125mm; 1/4” Universal joint; 1/2” Spark
plug 21mm; X10 Bits; L Hex Key Set:
1.5, 2, 2.5, 3, 4, 5, 6mm; 1/4” Chrome
sockets: 4, 5, 6, 7, 8, 9, 10,11,13mm; /2”
Chrome sockets: 10, 11, 12, 13, 14, 15,
16, 17, 18, 19, 21, 22, 24, 27mm
• 11 x 1/4” hex sockets: 4, 4.5, 5, 5.5, 6, • Fully polished chrome plated finish for
7, 8, 9, 10, 11, 13mm; 13 x 1/2” hex durability and rust resistance
sockets: 10, 11, 12, 13, 14, 15, 17, 19, • Comfortable and durable moulded handle
22, 24, 27, 30, 32mm; 1 x 1/4” Round withstands most industrial solvents
• 60 Piece set: 3/8”, 1/4” & 1/2” Round • Quick release and reverse switch
ratchet; 1/4” Spinner handle; 3/8” , 1/4” • Comfortable handle
& 1/2” Extention bar 75,125,150mm; • Clam-shell case and closed box design
1/2” Sliding T bar 250mm; 3/8”, 1/4” &
1/2” Universal joint; 1/2” Spark plug 16,
21mm; 1/4” Bit holder, X10 Bits; L Hex
Key Set: 1.5, 2, 2.5, 3, 4, 5, 6mm; 3/8”
Chrome sockets: 10, 11, 12, 13, 14,15,
16, 17, 18mm; 1/4” Chrome sockets: 4,
5, 6, 7, 8, 9, 10mm; 1/2” Chrome sockets:
13, 14, 16, 17,18, 19, 21, 22, 24, 27, 28,
29, 32mm
• 60 Piece set: 1/4” & 1/2” black chrome • Comfortable bi-material handle
MicroTough ratchet; 1/2” extention Bar • Easy to lock the box
125, 250mm; 1/4” extention bar 75mm; • Separate storage compartments for
T bar 125mm; flex handle 250mm; 1/4” & sockets and ratchet
1/2” universal joint; spark plug 16, 21mm; • Sockets have Premium Black Chrome
spinner handle; bit holder x10 Bits; hex finish
keys: 1.5, 2, 2.5, 3, 4, 5, 6mm; 1/4” black • Strong corrosion resistance
chrome sockets: 4, 4.5, 5, 5.5, 6, 7, 8, 9, • Laser etched markings for easy, clear
10, 11, 12, 13, 14mm; 1/2” Black chrome identification
Sockets: 8, 9, 10, 11, 12, 13, 14, 15, 16,
17,1 8, 19, 22, 24, 27, 30, 32mm
• 75 pcs. socket; Sockets 1/4”: 4, 4.5, • Fully polished chrome plated finish for
5, 5.5, 6, 7, 8, 9, 10mm; Sockets 3/8”: durability and rust resistance
10, 11, 12, 13, 14, 15, 16, 17, 18mm; • Comfortable and durable moulded handle
Sockets 1/2”: 13, 14, 17, 19, 22, 24, 27, withstands most industrial solvents
30, 32mm; Deep Sockets 1/4”: 8, 9, 10, • Slim pattern Chrome Vanadium
11, 12mm; Deep Sockets 3/8”: 13, 14, Combination Spanners
15, 17, 19mm; 3 Phillips hex bits: 1, 2, 3
pt; 3 Pozidriv hex bits: 1, 2, 3 pt; 3 slotted
hex bits: 4, 5.5, 7mm; 5 torx hex bits: 5
bits; 5 hex bits: 4, 5, 6, 8, 10mm; Round
head ratchet handle with quick release two
way ratchet
7
• 1/2” Square drive - DR. ratchet with DR.F * 1/2” DR.M integrated adaptor, DR.
bi-material handle, DR. 6 point socket: universal joint, DR. bit holder, DR. sliding
10-11-12-13-14-15-16-17-18-19-21- T-bar. 1/4” Hexagonal drive - DR. magnetic
22-24-27-30-32mm, DR. spark plug SKT: bit driver with bi-material grip, 31 drive
16-21mm, DR. 5” extension bar, DR. 10” bits (25mm) - Hexagonal: 3-4-5-6-8mm,
extension bar, 3/8” DR.F * 1/2” DR.M Slotted: 4-4.5-5-5.5-6-6.5-8mm, Phillips:
integrated adaptor, DR. universal joint. 1/4” 0-1-2-3, Pozidriv: 1-2-3, Torx: 10-15-20-
Square drive - DR. ratchet with bi-material 25-30-40, Tamperproof Torx: 10-15-20-
handle, DR. 6 point socket: 3.5-4-4.5-5- 25-30-40
5.5-6-7-8-9-10-11-12-13-14mm, DR.
6 point deep socket: 8-10-13mm, DR. 4”
extension bar, DR. 10” extension bar, 3/8”
TIPS
AND TRICKS
TIP 1 To effectively use sockets you need to be TIP 4 If the torque required to complete the fastening
sensitive to the way in which the nut turns on the bolt needs to be specific for functional or safety reasons
or screw stud. If the nut does not rotate smoothly you should use a torque wrench.
check to see that the thread is not ‘crossed’
TIP 5 Make sure that the socket size matches
or if the thread size or type differs from the bolt.
the fastener size. Even though the socket may locate
TIP 2 Run the nut up until finger tight and then on a nut that is slightly smaller the result may well be
apply the socket to finally tighten the nut. Under that the corners of the fastener will be deformed
normal conditions do not be tempted to over tighten and make future removal difficult.
fastenings.
TOP TIP If you need to work on a fastener beyond
TIP 3 The size of the ratchet handle is carefully
your normal reach select a locking extension bar
matched to a given set of socket sizes so that damage
enabling you to reach the nut without the risk of leaving
to the fastening is minimised. Whenever possible pull
the socket embedded in the machinery or engine
the ratchet handle towards you for better control.
compartment.
Stanley® 120 PIECE MAINTENANCE SET
7
- Fat Max bit holder - DIN hammer 300g
- 6 point 1/2” socket: 10, 11, 12, 13, 14, 15, - pin punch: 4 mm, 5 mm, 6 mm
16, 17, 18, 19, 20, 22, 24, 27, 30, 32mm, - center punch 3,2mm
- 1/2” ratchet - drill set
- 1/2” extension: 75 mm, 250 mm - mini Level
- 1/2” universal joint - 5 m Tylon tape
- 1-13-903 31 pc bit set - carbure
- metal saw
• Push to open drawer mechanism allows - 1/4’’ 6 point socket : 4; 4,5; 5; 5,5; 6;
drawers removal and secure the drawers in 7; 8; 9; 10; 11; 12; 13; 14 mm,
place during transportation - 1/4’’ extension 75 mm,
• Modular tool storage provides end user - 1/4’’ extension 150 mm,
with storage/organization device and - T bar 125 mm,
allows for easy transportation - 1/4’’ Spinner handle – similar to sets
• Top & Side handles for easier & better 1-94-649 / 1-94-651,
transportation - 1/4’’ Bit holder,
• 1 Assortment Tools Included for various job - 1/4” ratchet - bi material - pear head
applications – 1-86-395,
• 3 drawer plastic storage box and 3 - 1/4’ universal joint,
removable drawers with 3 handles: 2 on - 9 pc short hex key set in holder: 1,5; 2;
each side & 1 on the top 2,5; 3; 4; 5; 6; 7; 8 mm,
• Additional storage on top for screws - 16 bits : PZ1 - PZ2 - PH1 - PH2 - Slotted:
• Sets included: 4; 5,5; 6,5; 8 mm - Torx: 10; 15; 20; 25;
- Combination wrench 7; 8; 9; 10; 11; 12; 30; 40 - Hexagonal: 4 - 5 mm
13; 15; 16; 17; 19 mm, - Cushion grip screwdrivers: 6,5 x 30 mm
- DIN hammer - 300 g - wooden handle, - 3 x 75 mm - 4 x 75 mm - 6,5 x 100 mm
- Diagonal cutting pliers - 0-84-104, - 8 x 150 mm - PH3 x 150 mm
- Groove joint pliers - 250 mm - 0-84-110, - PH2 x 100 mm - PH1 x 75 mm
- Long nose pliers - 300 mm - 0-84-102, - PH0 x 60 mm - PH2 x 30 mm
1-94-737 50 x 97 x 73 cm - 1 3253561947377
• 7 drawer large rolling cabinet, - 1/4” Sq Drive 6-point socket module set
- 8 T handle hex keys module set - 5.5 to 14 mm and bits / 1-94-680,
- 2,5 -> 10 mm, - 3/8” Sq drive 6-point socket module set
- Metal saw & snips module set - 8 to 22 mm / 1-94-678, 1/2” Sq Drive
- torque wrench (40 - 210 Nm) 6-point socket module set - 10 to 32 mm
- 4 large combination wrench: 27 - 29 - 30 / 1-94-677,
- 32 mm, - 16 pc combination wrench module set
- adjustable wrench (250 mm) - 6 -> 24 mm / 1-94-937,
- 7 ratcheting combi wrenches - 10 pc L-pipe wrench module set
(8 -> 19 mm), - 8 -> 19 mm / 1-94-939,
- 4 file modul set - 200 mm - square / round - 8 Fat Max screwdriver module set
/ half round & flat, / 1-94-940,
- Measuring module kit : Max tape / calipter - 6 FatMax Tamper Torx screwdriver modul
/ riveting pliers, Large socket module set - set / 1-94-941,
10 -> 24 mm, - 2 pc plier module set / 1-94-944,
- Bit module set: flared, PH, PZ, Torx, - 4 pc mechanic plier module set
- Impact socket module set: 10 -> 24 mm / 1-94-945,
& Torx E10 -> E24, - 4 pc circlip plier module set / 1-94-943,
- Shock tool module set / 1-94-942
• Tray fits in rolling cabinet: ref. Stanley • Extensions: 125 & 250mm. Universal
1-94-737 joint: 66mm
• Sockets: 8-10-11-12-13-14-15-16-17- • 50 x 173 x 354
18-19-21-22-23-24-27-30-32mm. Mini
ratchet: 254mm
• Made to fit of the rolling cabinet (1-94- • 1-94-941: Tamper Torx: 10-15-20-25-
737) 30-40
• 1-94-940: 3.5x75/4x100/5.5x125/6.5x15
0/8x150/PHO/PH1/PH2
• Internal & External straight & bend at 90° • Straight-nose expansion pliers: for outside
circlips: 180mm - Ø 1.8mm - Ø 19 ->
60mm. 90° nose compression pliers
for outside circlips: 180mm - Ø 1.8mm
- Ø 19 -> 60mm. Straight-nose
compression pliers for outside circlips:
180mm - Ø 1.8mm – Ø 19 -> 60mm.
90° nose compression pliers for outside
circlips: 180mm - Ø 1.8mm - Ø 19 ->
60mm
• Fully forged from chrome vanadium steel • Maxi Drive open ended jaw shape
to ISO 3318 and DIN 3113 standards of maintains grip on fastener with only slight
accuracy and performance rotational pressure
• Nickel chrome plating protects against • Improved grip even on damaged nuts
corrosion • Polished head with satin finish to the
handle
4-87-096 6 x 7 mm X 6 3253564870962
4-87-097 8 x 9 mm X 6 3253564870979
4-87-098 10 x 11 mm X 6 3253564870986
4-87-099 12 x 13 mm X 6 3253564870993
4-87-100 14 x 15 mm X 6 3253564871006
4-87-101 16 x 17 mm X 6 3253564871013
4-87-102 18 x 19 mm X 6 3253564871020
4-87-103 20 x 22 mm X 6 3253564871037
4-87-104 21 x 23 mm X 6 3253564871044
4-87-105 24 x 27 mm X 4 3253564871051
4-87-106 25 x 28 mm X 4 3253564871068
4-87-107 30 x 32 mm X 4 3253564871075
7
1-13-275 17 x 19 mm - 5 3253561132759
1-13-256 18 x 19 mm - 5 3253561132568
1-13-257 20 x 22 mm - 10 3253561132575
1-13-258 21 x 23 mm - 10 3253561132582
1-13-262 4 x 5 mm - 10 3253561132639 1-13-279 22 x 24 mm - 10 3253561132797
1-13-250 6 x 7 mm - 10 3253561132506 1-13-259 24 x 27 mm - 10 3253561132599
1-13-251 8 x 9 mm - 10 3253561132513 1-13-260 25 x 28 mm - 10 3253561132605
1-13-265 8 x 10 mm - 10 3253561132650 1-13-261 26 x 28 mm - 5 3253561132612
1-13-252 10 x 11 mm - 10 3253561132520 1-13-281 27 x 29 mm - 10 3253561132810
1-13-267 10 x 13 mm - 10 3253561132674 1-13-282 27 x 30 mm - 10 3253561132827
1-13-268 11 x 13 mm - 10 3253561132681 1-13-909 30 x 32 mm - 5 3253561132612
1-13-253 12 x 13 mm - 10 3253561132537 1-13-285 33 x 35 mm - 2 3253561132858
1-13-272 13 x 17 mm - 5 3253561132728 1-13-287 34 x 36 mm - 2 3253561132872
1-13-254 14 x 15 mm - 5 3253561132544 1-13-286 36 x 41 mm - 2 3253561132865
1-13-255 16 x 17 mm - 5 3253561132551 1-13-288 38 x 42 mm - 2 3253561132889
• Fully forged from chrome vanadium steel • Improved grip even on damaged nuts
to ISO 3318 and DIN 3113 standards • Polished head with satin finish to the
of accuracy and performance handle
• Nickel chrome plating protects against • 4-87-051: 6x7,8x9,10x11,12x13,14x15,
corrosion 16x17,18x19,20x21 mm
• Maxi Drive open ended jaw shape • 4-87-052: 6x7,8x9,10x11,12x13,14x15,
maintains grip on fastener with only slight 16x17,18x19,20x21 mm
rotational pressure
• Fine heads - 15° angle of recovery • 1-17-382: 4x5, 6x7, 8x9, 10x11, 12x13,
• Matt chrome finish 14x15, 16x17, 18x19, 21x23, 22x24,
• 1-17-380: 4x5, 6x7, 8x9, 10x11, 12x13, 26x28, 27x29, 30x32, 33x35, 36x41,
14x15, 16x17, 18x19 38x42
• 1-17-381: 6x7, 8x9, 10x11, 12x13,
14x15, 16x17, 18x19, 21x23, 22x24,
26x28, 27x29, 30x32
7
• Slim open head - 21x23mm
• Both the open end head are angled at 15° • 95-770: 06x07 - 08x09 - 10x11 - 12x13
• MaxiDrive open ended jaw shape maintains - 14x15 - 16x17 - 18x19 - 20x22 - 21x23
grip on fastener with only slight rotational - 24x26 - 25x28 - 30x32mm
pressure • 95-771: 1/4x5/16 - 5/16x3/8 - 3/8x7/16
• 95-767: 06x07 - 08x09 - 10x11 - 12x13 - 7/16x1/2 - 1/2x9/16 - 9/16x5/8
- 14x15 - 16x17mm - 13/16x7/8 - 15/16x1 - 1 1/16x1 1/4
• 95-768: 06x07 - 08x09 - 10x11 - 12x13 - 3/4x11/16” - 3/4x7/8” - 1-1/8x1-1/4”
- 14x15 - 16x17 - 18x19 - 20x22mm
1-95-767 6 pc - 10 3253561957673
1-95-768 8 pc - 5 3253561957680
1-95-769 10 pc - 5 3253561957697
1-95-770 12 pc - 2 3253561957703
1-95-771 12 pc - 2 3253561957710
• Fully forged from chrome vanadium steel • Slim pattern combines maximum strength
to ISO 3318 and DIN 3113 standards of with optimum accessibility
accuracy and performance • Improved grip even on damaged nuts
• Nickel chrome plating protects against
corrosion
COMBINATION WRENCHES
1-17-710 32 mm - 5 3253561177101
1-17-711 33 mm - 5 3253561177118
1-17-700 19 mm - 10 3253561177002 1-17-712 34 mm - 5 3253561177125
1-17-701 21 mm - 10 3253561177019 1-17-713 35 mm - 5 3253561177132
1-17-702 22 mm - 10 3253561177026 1-17-714 36 mm - 2 3253561177149
1-17-703 23 mm - 10 3253561177033 1-17-715 38 mm - 2 3253561177156
1-17-704 24 mm - 5 3253561177040 1-17-716 41 mm - 2 3253561177163
1-17-705 26 mm - 5 3253561177057 1-17-717 42 mm - 2 3253561177170
1-17-706 27 mm - 5 3253561177064 1-17-718 46 mm - 2 3253561177187
1-17-709 30 mm - 5 3253561177095 1-17-719 50 mm - 2 3253561177194
• Forged Chrome Vanadium Combination • 4-87-054: 8 pcs 8, 10, 11, 13, 14, 15,
spanners featuring the reduced slip, 17, 22 mm
• Maxi Drive jaw profile for superior • 4-87-618: 8 pcs 8, 10, 12, 13, 16, 17,
performance 18, 19 mm
• 4-87-053: 6 pcs 10, 11, 13, 14, 15,
17 mm
• Forged Chrome Vanadium Combination • 5-87-054: 8 pcs 8, 10, 11, 13, 14, 15,
spanners featuring the reduced slip, 17, 22 mm
• Maxi Drive jaw profile for superior • 5-87-618: 8 pcst 8, 10, 12, 13, 16, 17,
performance 18, 19 mm
7
• Forged Chrome Vanadium Combination • 8 combination Spanners supplied with
spanners featuring the reduced slip, a roll up vinyl wallet for easy storage
• Maxi Drive jaw profile for superior • 14 pcs 10, 11, 12, 13, 14, 17, 19, 21, 22,
performance 23, 24, 28, 30, 32 mm
• Black chrome combination wench: 10, 11, • Laser etched markings for easy, clear
12 ,13, 14, 15mm identification
• Premium Black Chrome finish • Re-usable rack for easy home storage
• Strong corrosion resistance
7
4-94-613 6 pcs X 6 3253564946131
• Black chrome combination wench: 7, 8, 9, • Laser etched markings for easy, clear
10, 11, 12, 13, 14, 15, 16, 17mm identification
• Premium Black Chrome finish • Re-usable rack for easy home storage
• Strong corrosion resistance
1-17-728 14 mm - 10 3253561177286
1-17-729 15 mm - 5 3253561177293
1-17-730 16 mm - 5 3253561177309
1-17-731 17 mm - 5 3253561177316
1-17-732 18 mm - 10 3253561177323
1-17-733 19 mm - 10 3253561177330
1-17-734 21 mm - 10 3253561177347
1-17-735 22 mm - 10 3253561177354
1-17-720 6 mm - 5 3253561177200 1-17-736 23 mm - 10 3253561177361
1-17-721 7 mm - 5 3253561177217 1-17-737 24 mm - 10 3253561177378
1-17-722 8 mm - 10 3253561177224 1-17-738 26 mm - 10 3253561177385
1-17-723 9 mm - 10 3253561177231 1-17-739 27 mm - 10 3253561177392
1-17-724 10 mm - 10 3253561177248 1-17-740 28 mm - 10 3253561177408
1-17-725 11 mm - 10 3253561177255 1-17-741 29 mm - 10 3253561177415
1-17-726 12 mm - 10 3253561177262 1-17-742 30 mm - 10 3253561177422
1-17-727 13 mm - 10 3253561177279 1-17-743 32 mm - 10 3253561177439
• Short key for working in restricted spaces • Polygonal head angled at 15°
• Maxi Drive Profile: torque transmission
through fastener flats instead of corners
1-95-775 12 pc - 5 3253561957758
1-95-776 17 pc - 5 3253561957765
1-95-777 21 pc - 2 3253561957772
1-95-979 26 pc - 2 3253561959790
• Specially shaped open end engages • Unique plastic storage rack with POS
and disengages without the need to test facility
remove the spanner from the nut • 4-89-997: 8 pcs 8, 10, 11, 12, 13, 14,
• Enables operator to work much faster 15, 16 mm
• Satin finished nickel chrome plating
protects against corrosion
• Ratcheting box end eliminates the need to • Satin finished nickel chrome plating
disengage the wrench from the fastener protects against corrosion
• 5 degree angle of engagement of ratchet • Unique plastic storage rack with POS test
mechanism effective in the most restricted facility
of spaces
4-89-939 14 mm X 10 3253564899390
4-89-934 8 mm X 10 3253564899345 4-89-940 15 mm X 10 3253564899406
4-89-935 9 mm X 10 3253564899352 4-89-941 16 mm X 10 3253564899413
4-89-936 10 mm X 10 3253564899369 4-89-942 17 mm X 10 3253564899420
4-89-937 12 mm X 10 3253564899376 4-89-943 18 mm X 10 3253564899437
4-89-938 13 mm X 10 3253564899383 4-89-944 19 mm X 10 3253564899444
1-17-375
1-17-369
7 pcs.
12 pcs.
-
-
5
1
3253561134548
3253561133633
7
FLARE-NUT WRENCHES
1-17-391 11 x 13 mm - 10 3253561134715
1-17-393 14 x 17 mm - 10 3253561134739
1-17-394 17 x 19 mm - 10 3253561134746
1-17-395 19 x 22 mm - 10 3253561134753
1-17-396 22 x 24 mm - 10 3253561134760
1-17-388 8 x 10 mm - 10 3253561134685 1-17-368 24 x 27 mm - 10 3253561134777
1-17-389 10 x 11 mm - 10 3253561134692 1-17-398 30 x 32 mm - 10 3253561134784
1-17-390 10 x 12 mm - 10 3253561134708 1-17-399 36 x 41 mm - 10 3253561134791
• 6 pcs. set: 10, 12, 13, 16, 17, 19 mm • Satin finished nickel chrome plating
• Ratcheting box end eliminates the need to protects against corrosion
disengage the wrench from the fastener • Unique plastic storage rack with POS test
• 5 degree angle of engagement of ratchet facility
mechanism effective in the most restricted
of spaces
• More effective and quicker tightening • Powerful tightening: 12 point ring end
• Pivoting head enables ratcheting functions for extreme leverage when high torque is
• Elimination of re-position on fasteners after required - ring angled at 15°
each rotation • Resistance: forged from chrome vanadium
7
• 2 way ratchet functions; to tighten and steel
un-tighten by reversal • Comfortable with better grip: thicker shaft
• Product life cycle tested more than 50,000 and increased surface area for increased
times to ensure reliability grip
• Easy to use: chamfered end for easy on • Multiple uses for those in the plumbing,
and off, and side and top approach construction and automotive industry as
• Time saving: approximately 50% less vs well as DIY
regular open end wrench • Satin chrome plating finish
• Compact head for uses in restricted spaces • Exclusivity: STANLEY patented innovation
due to its slim profile • Try Me packaging
• Powerful tightening and fastener
protection: torque transmitted through the
flat section instead of corners –> better
and more optimum tightening with no
rounding of the fastener
• Fully forged from chrome vanadium steel • Slim pattern combines maximum
to ISO 3318 and DIN 3113 standards of strength with optimum accessibility
accuracy and performance • Ideal where high force is needed to turn
• Nickel chrome plating protects against a nut without damage
corrosion
OFFSET-RING WRENCH
1-95-772 8 pc - 2 3253561957727
1-95-773 10 pc - 2 3253561957734
7
1-95-774 12 pc - 2 3253561957741
1-13-406 19 mm - 10 3253561134067
1-13-407 20 mm - 10 3253561134074
1-13-408 21 mm - 10 3253561134081
1-13-409 22 mm - 10 3253561134098
1-13-393 6 mm - 10 3253561133930 1-13-410 23 mm - 10 3253561134104
1-13-394 7 mm - 10 3253561133947 1-13-411 24 mm - 10 3253561134111
1-13-395 8 mm - 10 3253561133945 1-13-451 25 mm - 5 3253561134517
1-13-396 9 mm - 10 3253561133961 1-13-412 26 mm - 2 3253561134128
1-13-397 10 mm - 10 3253561133978 1-13-413 27 mm - 2 3253561134135
1-13-398 11 mm - 10 3253561133985 1-13-452 28 mm - 5 3253561134524
1-13-399 12 mm - 10 3253561133992 1-13-453 29 mm - 2 3253561134531
1-13-400 13 mm - 10 3253561134005 1-13-414 30 mm - 2 3253561134142
1-13-401 14 mm - 10 3253561134012 1-13-454 31 mm - 2 3253561134548
1-13-402 15 mm - 10 3253561134029 1-13-415 32 mm - 2 3253561134159
1-13-403 16 mm - 10 3253561134036 1-13-455 34 mm - 2 3253561134555
1-13-404 17 mm - 10 3253561134043 1-13-456 35 mm - 2 3253561134562
1-13-405 18 mm - 10 3253561134050 1-13-457 36 mm - 2 3253561134579
7
1-13-376 14 mm - 10 3253561133763
1-13-377 15 mm - 10 3253561133770
1-13-378 16 mm - 10 3253561133787
1-13-379 17 mm - 10 3253561133794
1-13-380 18 mm - 10 3253561133800
1-13-381 19 mm - 10 3253561133817
1-13-458 6 mm - 10 3253561134586 1-13-382 20 mm - 10 3253561133824
1-13-459 7 mm - 10 3253561134593 1-13-383 21 mm - 10 3253561133831
1-13-370 8 mm - 10 3253561133701 1-13-384 22 mm - 10 3253561133848
1-13-371 9 mm - 10 3253561133718 1-13-385 23 mm - 10 3253561133855
1-13-372 10 mm - 10 3253561133725 1-13-386 24 mm - 5 3253561133862
1-13-373 11 mm - 10 3253561133732 1-13-388 27 mm - 5 3253561133886
1-13-374 12 mm - 10 3253561133749 1-13-389 30 mm - 5 3253561133893
1-13-375 13 mm - 10 3253561133756 1-13-390 32 mm - 5 3253561133909
• Finish: matt chrome • 1-17-383: 8, 10, 11, 12, 13, 14, 16,
• Forged wrench 17, 18, 19mm
• Maxi Drive profile: torque transmission • 1-13-416: 8, 9, 10, 11, 12, 13, 14, 15,
through fastener flats instead of corners 16, 17, 18, 19, 21, 22, 23, 24mm
• 1-17-387: 8, 10, 11, 12, 13, 14, 16, 17, • 1-17-386: 8, 9,10, 11, 12, 13, 14, 15, 16,
18, 19mm 17, 18, 19, 21, 22, 23, 24mm
• Fully forged from chrome vanadium steel • Nickel chrome plating protects against
to ISO 2236 and NFE 74 303 standards corrosion
of accuracy and performance • Ideal where high force is needed
to turn a nut without damage
7
• Use for construction, plumbing, automotive / 8” – 250 mm / 10” – 300 mm / 12”
& home uses - 375 mm / 15”
• Chrome vanadium forged body • At ISO 6787 / DIN 3117 / ASME B 107.8M
• Phosphate finish specifications
• Fully forged from chrome vanadium steel • When jaw has been adjusted to size
for optimum performance of nut it can be locked
• Knurled jaw adjustment screw • Prevents wrench from slipping off fastener
• Polished head, nickel chrome plated for
protection against corrosion
ADJUSTABLE WRENCH
• Fully forged from chrome vanadium steel • Polished head, nickel chrome plated
for optimum performance for protection against corrosion
• Knurled jaw adjustment screw • 23 degree head angle for improved
accessibility to the nut
• ‘Test me’ presentation card • Large size bi-material handle for comfort
7
• One tool accommodates a wide range of and performance
fastener sizes • Innovative ratcheting and automatic sizing
• Convex surface profile to prevent the nuts feature speeds up task completion
matting • Forged body construction delivers high
• Tightening and untightening without torque
removing the spanner from the nut • Self adjusting eliminating the need to
• Ratchet effect grip spanner for very fast re-position wrench on the fastener after
adjustment each rotation
1-13-917 5 mm - 28 x 80 - 10 3253561139178
1-13-918 6 mm - 32 x 90 - 10 3253561139185
1-13-919 7 mm - 34 x 95 - 10 3253561139192
1-13-920 8 mm - 36 x 100 - 10 3253561139208
1-13-921 9 mm - 38 x 105 - 10 3253561139215
1-13-922 10 mm - 40 x 112 - 10 3253561139222
1-13-911 1,3 mm - 13 x 45 - 10 3253561139116 1-13-923 11 mm - 42 x 118 - 5 3253561139239
1-13-912 1,5 mm - 13 x 45 - 10 3253561139123 1-13-924 12 mm - 45 x 125 - 5 3253561139246
1-13-913 2 mm - 16 x 50 - 10 3253561139130 1-13-925 13 mm - 50 x 135 - 5 3253561139253
1-13-914 2,5 mm - 17 x 62 - 10 3253561139147 1-13-926 14 mm - 55 x 140 - 5 3253561139260
1-13-915 3 mm - 20 x 65 - 10 3253561139154 1-13-927 17 mm - 63 x 160 - 5 3253561139277
1-13-916 4 mm - 25 x 70 - 10 3253561139161 1-13-928 19 mm - 70 x 180 - 5 3253561139284
7
1-13-969 5 mm - 28 x 115 - 10 3253561139679
1-13-970 6 mm - 32 x 135 - 10 3253561139703
1-13-971 7 mm - 34 x 140 - 10 3253561139710
1-13-964 1,5 mm - 14 x 62 - 10 3253561139642 1-13-972 8 mm - 36 x 150 - 10 3253561139727
1-13-965 2 mm - 16 x 75 - 10 3253561139659 1-13-973 9 mm - 38 x 160 - 10 3253561139734
1-13-966 2,5 mm - 18 x 85 - 10 3253561139666 1-13-974 10 mm - 40 x 170 - 10 3253561139741
1-13-967 3 mm - 20 x 90 - 10 3253561139673 1-13-975 12 mm - 45 x 190 - 5 3253561139758
• Ergonomic tee-handle allows effective use • Spherical head gives a working angle
of either end of key of up to 30°
• Finish: polished phosphate
• 0-89-904: 1.5-2-2.5-3-4-5-6-8-10 mm
• Ball hex configuration on the long arm to
• All keys stored in a size marked plastic
holder for easy selection
7
allow offset driving of hard to reach set • Additional multi position handle for use
screws in line or as a T or L handle
• Straight hex on short arm for maximum
leverage
• Ratcheting Mechanism – Industry first for • Removable side bits for improved torque
T-Handle. This speeds up the application • Drive will fit all ¼” sizes (most common
as you can keep the key in the fastener drive)
while returning tool to the starting position • Set includes: Nut Drivers, Socket Adapters,
• Heavy Duty Ergonomic Handle – More Long and Short Keys (Phillips, Pozi, Torx,
robust and lasts longer in tough worksite Hex & Slotted)
conditions. • PZ1; PZ2 x 2; PZ3 35mm - PH1; PH2;
• Removable ¼” drive key sizes fit into PH3 35mm - SL 3; 4,5; 6-8 35mm - PZ1;
ratcheting handle - this means the user PZ2 100mm - PZ2; PZ3 150mm - 8mm
only needs one set. 150mm - 2.5; 3mm 100mm - 4; 5; 6mm
• Compact and sturdy carrying case – safe 150mm - SL 4,5; 6-8 150mm - T15; T20;
storage of the kit and less chance of T25 150mm - T Handle Ratchet - Blow
leaving a key behind on site Case
• Ratcheting Mechanism – Industry First for • Drive will Fit all ¼” Sizes (most common
T-Handle. This Speeds Up the Application drive)
as you can Keep the Key in the Fastener • Set includes: Nut Drivers, Socket Adapters,
While Returning Tool to the Starting Long and Short Keys (Phillips, Pozi, Torx,
Position Hex & Slotted)
• Heavy Duty Ergonomic Handle – More • PZ1; PZ2 x 2; PZ3 35mm - SL 3; 4,5
Robust and Lasts Longer in Tough Worksite 35mm - 2.5; 3; 4; 5; 6; 8mm 35mm
Conditions - PZ1; PZ2 100mm - PZ1; PZ2; PZ3
• Removable ¼” Drive Key Sizes Fit into 150mm - PZ2 200mm - 2.5; 3mm
Ratcheting Handle - Means the User Only 100mm - 4; 5; 6mm 150mm - 8mm
Needs One Set. 200mm - T15; T20; T25 150mm - T15;
• Compact and Sturdy Carrying Case – Safe T20; T25 50mm - PH1; PH2 150mm - SL
Storage of the Kit and Less Chance of 6-8 150mm - PH1; PH2 50mm - SL 6-8
Leaving a Key Behind on Site. 50mm - T Handle Ratchet - Nut Driver 8,
• Removable Side Bits for Improved Torque 10, 12mm - Blow Case, 1/4 DR Adapter
x2
• Lock In Place feature to lock down keys • Extra long keys give easy access for
and prevents unwanted movement of the recessed bolts
Handle in Use - this is an Industry First • Hex Keys lock into 3 positions; 90°, 135°,
• Convenient “Button Lock” releases Hex 180° for flexibility and ultimate access in
Keys for secure and easy change from tight spaces
moving to locked • Metric, Standard American English & TORX
• Ergonomic handle for better grip allowing Versions available to cover maximum range
application of more torque by the user of applications
• 8 piece Torx configured tips made from • T9 -T10 -T15 -T20 - T25 -T27 -T30
high tensile steel -T40
• Hex keys fold out for easy access and • SAE, Metric and Torx Sets to Fit Wide
storage Assortment of Fasteners
• Rubber grip for outstanding comfort • 0-95-935: 1,5; 2; 2,5; 3; 4; 4,5; 5; 5,5;
• Once the hex key is locked into place the 6 mm
storage unit Becomes the driver handle • 0-95-937: 7/64”, 7/32”, 5/32”, 3/16”,
• Chrome Vanadium Steel for Increased 1/8”, 5/64”, 3/32”, 9/64”, 1/4”
Torque and Durability • 0-95-961: Torx: 8, 9, 10, 15, 20, 25, 30,
• High Impact & Ergonomic Case for 40
Improved Comfort
• sets of metric standard hex keys in high • 0-69-252 – 8 pcs.: 1/16, 5/64, 3/32,
tensile steel 1/8, 5/32, 3/16, 7/32, 1/4”
• All keys stored in a size marked and colour • 0-69-256 – 9 pcs. boll: 1.5, 2, 2.5, 3, 4,
coded plastic holder for easy selection 5, 6, 8, 10 mm
• (Red=Metric), (Yellow=Imperial), • 0-69-253 – 10 pcs.: 1.5, 2, 2.5, 3, 4, 5,
(Green=Torx) 5.5, 6, 8, 10 mm
• 0-69-251 – 8 pcs.: 1.5, 2, 2.5, 3, 4, 5, • 0-69-257 - 12 pcs.: 1/16, 5/64, 3/32,
5.5, 6 mm 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4,
5/16, 3/8”
7 • Compact sleeve-case
• Silicium steel
• Finish: black phosphate
0-84-009 0-84-016
0-84-000
0-84-001
0-84-002
0-84-003 0-84-010
0-84-004
0-84-005
0-84-006 0-84-008
0-84-007
7
0-84-294
0-84-294 waterpump plier, 255 mm X 6 3253560842949
0-84-000 combination plier, 160 mm X 6 3253560840006
0-84-001 combination plier, 175 mm X 6 3253560840013
0-84-002 combination plier, 200 mm X 6 3253560840020
0-84-003 diagonal cutting pliers, 160 mm X 6 3253560840037
0-84-004 diagonal cutting pliers, 180 mm X 6 3253560840044
0-84-005 diagonal cutting pliers, 200 mm X 6 3253560840051
0-84-009 narrow diagonal plier, 160 mm X 6 3253560840099
0-84-016 end cutters, 160 mm X 6 3253560840167
0-84-006 long nose plier, 160 mm X 6 3253560840068
• Special pivot design allows for easier • Hand finished and induction hardened
cutting cutting edges for longer life
• Bi-material cushion grip handles insulated • 84-489 - Combination pliers - 165 mm,
up to 1000V for safety Half round long nose pliers - 160 mm,
• Forged from chrome nickel steel for Diagonal copper wire cutting pliers
durability - 175 mm & Wire stripper - 170 mm
• Hand ground, induction hardened blade • Heat treated high chrome steel forging
for long life and high quality accuracy for long life and durability
• Interlocking joint assembly for smooth • Bi-material handle with secure grip
cutting grooving
• Cutting edge high frequency heat treated • DIN / ASO / ANSI compliant
with hand ground finish for high quality • Combination pliers - 165 mm, Diagonal
accurate cutting performance cutter - 165 mm & Half round long nose
pliers - 155 mm
0-89-866
0-89-867
0-89-868
0-89-875
0-89-871
0-89-872
0-89-873
0-89-869
0-89-870
0-89-860
0-89-874 0-89-861
0-89-862
7
0-89-866 combination plier, 150 mm X 4 3253560898663
0-89-867 combination plier, 180 mm X 4 3253560898670
0-84-496
0-89-868 combination plier, 200 mm X 4 3253560898687
0-89-860 angled diagonal cutting plier, 160 mm X 4 3253560898601
0-89-861 angled diagonal cutting plier, 180 mm X 4 3253560898618
0-89-862 angled diagonal cutting plier, 250 mm X 4 3253560898625
0-89-858 diagonal cutting plier, 160 mm X 4 3253560898588
0-89-859 diagonal cutting plier, 200 mm X 4 3253560898595
0-89-875 end cutter, 160 mm X 4 3253560898755
0-89-873 wire stripper, 160 mm X 4 3253560898731
0-89-869 long nose plier, 160 mm X 4 3253560898694
0-89-870 long nose plier, 200 mm X 4 3253560898700
0-89-871 bent long nose plier, 150 mm X 4 3253560898717
0-89-872 bent long nose plier, 200 mm X 4 3253560898724
0-89-874 cable cutter, 200 mm X 4 3253560898748 0-84-495
0-84-613 groove joint 200 m X 12 3253560846138
0-84-614 grooove joint 300 mm X 12 3253560846145
0-84-615 slip slot 150 mm X 12 3253560846152
0-84-629 slip joint 200 mm X 12 3253560846299
0-84-495 flat, 150 mm X 4 3253560844950
0-84-496 round, 165 mm X 4 3253560844967
0-84-880
0-84-881
165 mm
150 mm, short
X
X
6
6
3253560848804
3253560848811
7
DynaGrip NEEDLE NOSE PLIERS
0-84-054 0-84-077
0-84-622 • Brushed steel finish • Induction hardened and tempered metal
• Bi-material handles for comfort and grip for longer performance
even with oily hands • Forged carbon steel jaws and handle
for long life
0-84-055
0-84-056
0-84-623
0-84-071 0-84-053
0-84-072 0-84-625
0-84-073 0-84-074
• Forged carbon steel jaws and handles • 3piece DynaGrip® Plier Set - Universal
• Induction hardened and tempered for long Bimaterial, Water Pump, Diagonal
7
life performance • 84-485: Combination pliers - 150 mm,
• Cutting jaws machined to a close fit Diagonal piano wire cutting pliers
for efficient cutting - 150 mm & Half round Long nose pliers
• Accurately machined and fitted hinge - 150 mm
for smooth functioning • 84-487 5: Combination pliers - 150 mm,
• All exposed steel parts polished and clear Diagonal piano wire cutting pliers
lacquered for protection against corrosion - 150 mm, Half round long nose pliers
• Bi-material handles for comfort and grip - 150 mm, Water pump pliers - 240 mm
even with oily hands & Wire stripper - 150 mm
• Built in wire cutter on the curved jaw • Forged and machined jaws for maximum
models for convenience durability
• Chrome plating • Non-pinching “pull” jaw release improves
safety and ease of opening
• Forged and machined jaws for maximum • Screw adjusts the jaws and the amount
durability of clamping pressure
• Built in wire cutter on the curved jaw • Non-pinching “pull” jaw release improves
models for convenience safety and ease of opening
• Chrome plating is corrosion resistant
for long life
• Long Nose gives better access and is also • Screw adjusts the jaws and the amount
ideal for more delicate work of clamping pressure for precision work
• Chrome plating is corrosion resistant • Non-pinching “pull” jaw release improves
for long life safety and ease of opening
• Built in wire cutter on the curved jaw • Screw adjusts the jaws and the amount
models for convenience of clamping pressure for precision work
• Chrome plating • Non-pinching “pull” jaw release improves
safety and ease of opening
7
0-84-814 200 mm (8”) X 4 3253560848149
• Built in wire cutter on the curved jaw • Deep throat C clamp ideal for large,
models for convenience bulkier items where more clamping
• Chrome plating capacity is needed
• Screw adjusts the jaws and the amount of • Non-pinching “pull” jaw release improves
clamping pressure for precision work safety and ease of opening
12 in 1 MULTI-TOOL
7
2-84-168 10-25 mm, straight nose pliers X 10 3253562841681
2-84-170 10-25 mm, curved nose pliers X 10 3253562841704
1-17-908 • Straight - nose outside circlips pliers • Conforms to DIN 5254 and NF E 73-130
1-17-909
standards
1-17-910
1-17-911
7
1-17-918
1-17-919
1-17-920
1-17-921 • Conforms to DIN 5256 AND NF E 73-130 • Bi-material grips
1-17-922 standards • Polished finish
1-17-923 • Striated nozzle for reinforcing the grip • Anti-corrosion varnished finish
• Thin nozzle for access to confined spaces • Inherited Attributes
• High grade alloy steel for long life • Conforms to ISO 9242 and DIN 5242
• Induction hardened cutting edges standards
to maintain 1st cut sharpness
CARPENTER’S PINCERS
• To twist and cut thicker wire in one • Convex handles for comfortable ease
operation: fast, reliable and economical of use
• Precise cutting edges and double heat • Round edge handles for quick rotations
treatment (60 HRC)for clean cutting lancing • Very long lever arm and pivot pin closer
cords to jaws for maximum cutting power and
• Max Ø 4,5mm on soft wire 80 kg/mm2 & reduced cutting effort
Max Ø 1,6mm on hard wire 160 kg/mm2 • Cuts everything from plastic to nails
1-95-096
1-95-097
200 mm
220 mm
-
-
10
10
3253561950964
3253561950971
4-95-096
4-95-097
200 mm
220 mm
X
X
10
10
3253564950961
3253564950978
7
1-95-098 250 mm - 10 3253561950988 4-95-098 250 mm X 10 3253564950985
1-95-099 280 mm - 10 3253561950995 4-95-099 280 mm X 10 3253564950992
1-95-100 300 mm - 10 3253561951008 4-95-100 300 mm X 10 3253564951005
• Titamium Nitride coated blades allows jaws • Will cut sheet thickness; 18swg / 1.2mm
to stay sharp longer with longer life mild steel, 22swg / 0.8mm stainless steel
• Capable of 47k cycles so ideal for • Flush fitting hardware prevents snagging
intensives applications in workpiece
• Chrome Molybdenum steel with serrated • Internal locking mechanism with one
jaw blades gives a stable bite and prevents handed auto release
slippage • Xtreme soft grip handles for comfort
• Suitable for cutting aluminium, sheet UPVC, • Permanent identification plate for the
wire mesh, leather, copper and plastic direction of cutting
• Made from forged alloy steel for strength • Chrome plated nuts and bolts
and durability • Cuts up to 18 gauge mild steel
• Automatic unblocking of the lock/seal by 0.7 to 1.2mm
simple pressure • Bi-material easy grip handles
• Suitable for cutting aluminium, sheet UPVC, • One handed automatic latch release
wire mesh, leather, copper and plastic • Double pivot action for high cutting power
• Cuts up to 18 gauge mild steel 0.7 • Made from forged alloy steel forstrength
to 1.2mm and durability
• Bi-material easy grip handles
7 2-14-567
2-14-568
left
right
X
X
6
6
3253562145673
3253562145680
• Suitable for cutting aluminium, sheet UPVC, • One handed automatic latch release
wire mesh, leather, copper and plastic • Double pivot action for high cutting power
• Cuts up to 18 gauge mild steel 0.7 • Made from forged alloy steel forstrength
to 1.2mm and durability
• Bi-material easy grip handles
FRETSAW SHEARS
7
1-84-191 260 mm - 2 3253561841910
SPARE BLADES
7 1-83-067
1-83-068
HD 125 mm (5”)
HD 150 mm (6”)
-
-
1
1
3253561830679
3253561830686
• Infinitely adjustable and lockable in any • Removable jaw pads protect surfaces
orientation from marring and damage
• Integral screw clamp offers strength and • Machined jaw faces evenly distribute
easily attaches to most work surfaces clamping ant finish pressure
1-83-069 - - 1 3253561830693