Catalog
Catalog
Catalog
Grinding Wheels
All Weiler wheels are resin bond formulated for fast, high quality grinding and cutting, and are reinforced with fiberglass webbing to provide stability.
Grain Selection Guide Fast Cut - ideal for use on hard welds and steel, stainless steel, A24N and in low pressure, large contact grinding where the harder wheel grade (R) dulls or glazes. Long Life - offers longer life than the softer wheel grade (N). Ideal for all general purpose grinding on structural steel, or in foundries or heavy fabrication applications. High Performance Zirconium - offers improved cut rate in high pressure applications. Ideal when grinding or cutting stainless steel, high carbon steel, cast iron and other metals.
Superior Construction Ensures Maximum Performance Weiler's Type 27 Wheels contain no fillers and are made with 100% abrasive grain to maximize cut rate.
Bonded
A24R
Z24T
Weiler: A side view of Weiler's Tiger Abrasives Type 27 Grinding Wheel shows the even distribution of grain from the top to the bottom of the wheel. This provides a consistent rate of cut throughout the product life.
Competitor's: A side view of competitor's Type 27 Grinding Wheel shows abrasive grain on the bottom portion of the wheel and filler grain on the top portion. The cut rate deteriorates dramatically when the filler portion of the wheel is reached.
30-45 Grain/Grit/Grade A24T A24T A24T A24T A24T A24T A24T A24T A24T Part No. 56431 56430 56429 56428 56427 56426 56425 56424 56423
NOTE
Marking System
Grade (Hardness) Grain Type
NOTE
For mounting wheels with 7/8" arbor holes on right angle grinders, use adapting nuts (Part No. 56494) as illustrated on page 406.
A 24 R
www.oki-bering.com 405
Grit Size
Cutting Wheels
Bonded
For a wide range of metal-cutting applications Dia. x Thickness x Arbor Hole Notching a piece of steel bar prior to welding. Applications Cutting Parting Notching 4" x 3/32" x 5/8" 4-" x x 4-" x 3/32" x 5/8"-11 5" x 3/32" x 7/8" 5" x 3/32" x 5/8"-11 7" x 3/32" x 7/8" 7" x 3/32" x 5/8"-11 9" x 3/32" x 7/8" 9" x 3/32" x 5/8"-11
3/32" 7/8"
Grain/Grit/Grade A24T A24T A24T A24T A24T A24T A24T A24T A24T
Part No. 56474 56475 56385 56476 56384 56383 56477 56382 56381
Adapting Nuts
For mounting wheels with 7/8" arbor holes on right angle grinders. For 4-" & 5" Angle Grinders. Use with Part No. 56103 & 56118 Thread Size Min. Wheel Thick.
1/16"
TIP
The following factors can cause wheel breakage: Excessive speed Excessive rate of wheel feed Improper mounting Improper machine conditions Work improperly clamped Misuse
5/8" - 11
To mount wheels with 7/8" arbor holes on right angle grinders, use adapting nuts (Part No. 56494), as illustrated at left.
406
www.oki-bering.com
Bonded
Flanges should be of equal diameter, recessed and at least one-third the diameter of the wheel.
Counter rotation of the work-piece is recommended for cutting large cross sections (over 8") and when cutting tubular stock. CORRECT INCORRECT
Work Operation Guide for Cut-Off Wheels RPM Feed Rate To maximize performance, run at or close to the Maximum Safe Free Speed or RPM. NEVER EXCEED the MSFS or RPM. Only the operator can determine if the feed rate is proper for an efficient operation. A good starting point for dry cutting most materials is 2-3 seconds per square inch.
Safety
Abrasive users and others in area must wear goggles or face shields over safety glasses. Safety guards must be used. Do not exceed maximum RPM.
www.oki-bering.com
407
Cut-Off Wheels
Small Type 1 Reinforced Wheels
For electric or air die grinders and angle grinders Dia. x Thickness x Arbor Hole 1-" x .035" x 1/8" 2" x .035" x " 2" x 1/16" x " 2" x 1/16" x " 2" x 1/16" x " 3" x .035" x " 3" x .035" x 3/8" 3" x 1/16" x " 3" x 1/16" x " 3" x 1/16" x " 3" x 1/16" x 3/8" 3" x 1/16" x 3/8" 3" x 1/16" x 3/8" 3" x 1/8" x 3/8" Cutting a piece of hex bar stock. 4" x .035" x " 4" x .035" x 3/8" 4" x 1/16" x " 4" x 1/16" x " 4" x 1/16" x " 4" x 1/16" x 3/8" 4" x 1/16" x 3/8" 4" x 1/16" x 3/8" 4" x 1/8" x 3/8" 4-" x 1/16" x 7/8" 5" x .035" x 3/8" 5" x .035" x 5/8" 5" x 1/16" x 5/8" 5" x 1/16" x 5/8" 5" x 1/16" x 7/8" Max. RPM 45,000 30,000 Grain/Grit/Grade A60T A60T A36T A46T A60T A60T A60T A36T A46T A60T A36T A46T A60T A36T A60T A60T A36T A46T A60T A36T A46T A60T A36T A60T A60T A60T A36T A60T A36T Part No. 56003 56013 56015 56016 56017 56061 56062 56065 56066 56067 56068 56069 56070 56076 56079 56080 56083 56084 56085 56086 56087 56088 56099 56103 56106 56108 56115 56117 56118
Bonded
25,000
19,000
13,500
NOTE
Marking System
Grade (Hardness) Grain Type
12,200
Grit Size
A 24 T
TIP
For maximum wheel life, select the coarsest, hardest wheel that will perform the cut.
"
3/8"
",
.035 to "
*Combination pack
408
www.oki-bering.com
Cut-off Wheel
Type 1 Reinforced Wheels
For tool room & machine shop use Dia. x Thickness x Arbor Hole 6" x .035" x " 6" x .035" x 5/8" 7" x .035" x 5/8" 7" x .035" x 1-" 7" x 1/16" x 5/8" 7" x 1/16" x 5/8" 7" x 1/16" x 1-" 8" x .035" x 1-" Max. RPM 10,200 Grain/Grit/Grade A60T A60T A60T A60T A36T A60T A60T A60T Part No. 56170 56171 56183 56184 56188 56190 56193 56199
8,740
7,640
Bonded 8
TIP
Convex wheel wear is a sign of proper wheel usage. Pointed wheel wear is a sign of improper usage. Wheel is too hard for application or feed rate is too slow for application.
Plastic Adapters
For Cut-Off Wheels with 1" arbor holes Wheel Arbor Hole Size 1" Adapted Arbor Hole Size 20mm Part No. 04455 14" x 1/8" x 1" 5,200
www.oki-bering.com
409
Resin Fiber Disc: Solid one-layer construction The cut rate of a resin fiber disc diminishes rapidly because, as the disc wears, no new abrasive grain is exposed.
Flap Discs
Product Selection
Selection Guide For Abrasive Flap Discs
Application Requirement High cut rate and consistent finish. Enables operator to trim non-marking backing, exposing more flaps, therefore extending life and increased flexibility.. A high cut rate and a long life. A high cut rate at a value price (maintains similar cut rate as original Tiger Discs). Increased conformability on contoured parts; enhanced ergonomics; long life; minimized gouging on value-added components. Increased conformability at a value price. Stainless steel and other high strength metal grinding applications. Abrasive Flap Disc Type Trimable Tiger Flap Disc Angled (Type 29) Original Tiger Disc Angled (Type 29) Original Tiger Disc Flat (Type 27) Vortec Pro Flap Disc Angled (Type 29) High Density Big Cat Flat (Type 27) High Density Vortec Pro Flap Disc Flat (Type 27) High Density Tiger Discs For Stainless Steel Flat (Type 27) BobCat Mini Disc Angled (Type 29) BobCat Mini Disc Flat (Type 27) Tool
For use on air and electric right angle die grinders. Ideal for small, tight areas; non-marking backing.
www.oki-bering.com
415
Part No. Phenolic Backing Zirconium Aluminum Oxide 50592 50593 50594 50595 50596 50601 50602 50603 50604 50605 50606 50608 50609 50610 50611 50612 50613 50614 50615 50616 50621 50622 50623 50624 50625 50626 50641 50642 50643 50644 50645 50646 50552 50553 50554 50555 50556 50561 50562 50563 50564 50565 50566 50571 50572 50573 50574 50575 50576 50581 50582 50583 50584 50585 50586 50631 50632 50633 50634 50635 50636
Aluminum Backing Zirconium 50502 50503 50504 50505 50506 50511 50512 50513 50514 50515 50516 50510 50517 50518 50519 50520 50509 50521 50522 50523 50524 50525 50526 50531 50532 50533 50534 50535 50536 50541 50542 50543 50544 50545 50546
4"
5/8"
15,000
Flap Discs
Blending and finishing edges of a flame-cut steel part. Applications Weld blending Grinding Deburring Deflashing Surface finishing and blending Edge chamfering Stock removal
4-"
7/8"
13,000
4-"
5/8"-11 Nut
13,000
5"
7/8"
12,000
Weilers Original Tiger Discs are designed for the serious industrial user who values both a high cut rate and long life.
For Best Results: Use 1 grit size coarser than resin fiber disc. Exception: 36 grit, use same size.
7"
7/8"
8,600
7"
5/8"-11 Nut
8,600
Adapting Nut (Not for use with Resin Fiber Discs) Abrasive Flap Disc Adapting Nut
* hen grinding steel and other ferrous materials, a 36 grit Tiger Disc is more productive than a W 24 grit. 24 grit Tiger Discs are most productive when used on aluminum and other soft materials.
For Use With 4" Flap Disc with 5/8" arbor hole (Can be used with an adjustable or combination wrench.) 4-", 5" & 7" Flap Discs with 7/8" arbor hole Part No. 56494 only
416
www.oki-bering.com
Part No. Phenolic Backing Zirconium Aluminum Oxide 50693 50694 50695 50696 50703 50704 50705 50706 50713 50714 50715 50716 50723 50724 50725 50726 50743 50744 50745 50746 50653 50654 50655 50656 50663 50664 50665 50666 50673 50674 50675 50676 50683 50684 50685 50686 50733 50734 50735 50736
4"
5/8"
15,000
4"
7/8"
13,000
Flap Discs
5"
7/8"
12,000
7"
7/8"
8,600
7"
5/8"-11 Nut
8,600
15-25 Max RPM Std. Pack Part No. 50002 13,000 10 50003 50004 50005 50006 13,000 10 50007 50008 50009 50010 12,000 10 50011 50012 50013 50014 12,000 10 50015 50016 50017
4"
4"
5/8"-11
60 80 120 40
5"
7/8"
60 80 120 40
5"
5/8"-11
60 80 120
The backing can be trimmed up to 3/8" from the original diameter, dramatically extending the life of the disc.
www.oki-bering.com
417
4"
5/8"
15,000
4-"
7/8"
13,000
Flap Discs
4-"
5/8"-11 Nut
13,000
5"
7/8"
12,000
*For Best Results: When grinding steel and other ferrous materials, a 36 grit Vortec flap disc is more productive than a 24 grit. 24 grit flap discs are most productive when used on aluminum and other soft materials.
7"
7/8"
8,600
7"
5/8"-11 Nut
8,600
Part No. Phenolic Back - Zirconium 31401 31402 31403 31404 31407 31408 31409 31410 31413 31414 31415 31416 31419 31420 31421 31422
4-"
7/8"
4-"
5/8"-11 Nut
13,000
7"
7/8"
8,600
7"
5/8"-11 Nut
8,600
418
www.oki-bering.com
0-15
Part No. Phenolic Back - Zirconium 31387 31388 31389 31390 31391 31392
4-"
5/8"-11 Nut
12,000
Flap Discs
15-25
Part No. 30822 30825 30826 30828 30831 30832 30834 30837 30838
Part No. 30821 30823 30824 30827 30829 30830 30833 30835 30836
4-"
13,000
7/8"
5/8"-11
7"
8,600
7/8"
5/8"-11
For Best Results: Use 1 grit size coarser than resin fiber disc. Exception: 36 grit, use same size.
Adapting Nuts and Spanner Wrench For use with Tiger, Vortec Pro and High Density Flap Discs Description Adapting Nuts Adapting Nuts Thread Size
3/8" - 24
For Use With 4" Flap Disc with 5/8" arbor hole (Can be used with an adjustable or combination wrench.) 4-", 5" & 7" Flap Discs with 7/8" arbor hole Part No. 56494 only
5/8"-11
Adapting Nut
Spanner Wrench
www.oki-bering.com
419
0-15
Part No. Phenolic Backing Zirconium Aluminum Oxide 50803 50804 50805 50806 50808 50809 50810 50823 50824 50825 50826 50843 50844 50845 50846 50763 50764 50765 50766 50783 50784 50785 50786 50833 50834 50835 50836
4-"
7/8"
12,000
Flap Discs
4-" Weld blending on an automotive part. Big Cat Applications Provides increased conformability and long life when: Weld blending Grinding Deburring Deflashing Stock removal Surface finishing and blending Edge chamfering 7"
5/8"-11 Nut
12,000
7/8"
8,600
7"
5/8"-11 Nut
8,600
Note: Weiler's Specialty Abrasive Flap Discs provide users with a flap disc designed for application-specific situations.
Tiger Discs for Stainless Steel: ade with specially formulated, M fast-cutting abrasive cloth which prevents dulling and glazing of abrasive grains leading to consistently high cut rates. 0-65% more abrasive cloth than 5 conventional flap discs - disc life is extended resulting in the lowest cost-per-piece finished. igh density flat configuration adds H flexibility which promotes smoother grinding action and reduces the possibility of damage to high-value stainless parts. esigned to work under lighter D pressures which minimizes gouging, undercutting, heat discoloration and thermal distortion, and reduces operator fatigue. For use in applications for stainless steel such as: Weld blending Grinding Heavy deburring Deflashing Stock removal and dressing Finishing and blending Edge chamfering
Tiger Discs for Stainless Steel High Density Flat Style (Type 27)
60 Grit: For maximum cut rate; 80 Grit: For superior finish Dia. 4-" 4-" 7" 7" Arbor Hole
7/8" 5/8"-11 Nut 7/8" 5/8"-11 Nut
0-15
Grit Size 60 80 60 80 60 80 60 80
Part No. Phenolic Backing 50864 50865 50869 50870 50884 50885 50894 50895
*For Best Results: When grinding welds that are less than a " thick, use a 60 grit Tiger Disc for Stainless Steel as the first step, instead of a hard grinding wheel. This disc grinds faster while producing a smoother finish than a grinding wheel. This process cuts down the time and the number of abrasive products required to grind and finish the welds.
420
www.oki-bering.com
2"
30,000
Flap Discs
3"
20,000
Patented
2"
30,000
3"
20,000
Patented
3" BobCats can also be mounted on Norton Speed-Lok TS back-up pads and Weiler metal hub pad Part No. 60509. Speed-Lok TS is a registered trademark of Norton Co.
www.oki-bering.com
421
Type 1 Products:
This product category includes wheels ranging from 1- " to 14" diameters, in various grit sizes, and aluminum oxide and silicon carbide abrasive grains. Type 1 Wheels are for use on electric or air die grinders, tool room grinders, circular saws, stationary machines, portable gas or electric saws and chop saws.
Coated 8
Safety
Abrasive users and others in area must wear goggles or face shields over safety glasses. Safety guards must be used. Do not exceed maximum RPM.
432
www.oki-bering.com
4"
5/8"
4-"
7/8"
Coated 8
5" Grinding welds on a fabricated steel part. Applications Zirconium: igh performance grinding of stainless H steel, tool steel and hard-to-grind materials Aluminum Oxide: ll purpose weld blending, grinding, A surface preparation and finishing of metals, plastic, wood and fiberglass.
7/8"
7"
7/8"
9"
7/8"
5/8"-11
* ther thread sizes avail ble on special orders. Please specify model number O a and machine make on which acces ories are to be used. s
www.oki-bering.com
433
Aluminum Oxide Dia. 2" Grit Size 36 60 80 120 36 60 80 120 Part No. Plastic Button*
Coated
AL-tra CUT Discs are specially formulated for superior grinding performance - on aluminum. AL-tra CUTs improve grinding on aluminum 400-800%! These revolutionary discs resist loading, ensure higher cut rates, prolong disc life and achieve a superior finish compared to conventional sanding/grinding discs in the market. AL-tra CUT Discs replace conventional resin fiber discs 5 to 1 or more.
Part No. 59821 59823 59824 59826 59862 59864 59865 59867
7"
7/8"
3"
Do not exceed maximum RPM of back-up pad. Do not store AL-tra CUT Discs above 120 F.
* ompatible with 3M Roloc back-up pads. C (Roloc is a trademark of 3M.) + ompatible with Norton Speed-Lok TS C back-up pads. (Speed-Lok TS is a registered trademark of Norton Co.)
Do not exceed maximum RPM of back-up pad. Do not store AL-tra CUT Discs above 120 F.
Back-up Pads
for 2" & 3" Discs Blending aluminum welds on a machine bracket. Applications For aluminum applications such as: Weld blending Grinding Deburring Finishing Size 2" x " stem 3" x " stem Max. RPM 25,000 20,000 Part No. Plastic Button Metal Hub
51551 51552
60508 60509
Disc Accessories
for 4-" & 7" Discs Description Thread Size
5/8"-11* 5/8"-11
NOTE
2" & 3" AL-tra CUT Discs vs. Blending Discs
AL-tra CUT Discs are made with a fiber backing, as opposed to cloth backed blending discs. This tougher fiber backing extends life, even in the most demanding applications. Combining this increased toughness with the special load-resistant formulation provides a long-life disc with superior, unparalleled grinding performance compared to conventional blending discs.
4-" Back-up Pad 7" Back-up Pad Spanner Wrench Disc Nut
5/8"-11
* ther thread sizes avail ble on special orders. Please specify O a model number and machine make on which acces ories are s to be used.
434
www.oki-bering.com
Weiler's Flap Wheels are designed with a solid hub construction which: nables flap wheels to be rated at higher RPM's, providing more E aggressive cutting action and increased productivity. rovides perfect balance leading to smooth, chatter-free finishing. P Applications Final finish on metal surfaces eburring and mismatch removal on D machined parts Edge blending lending and finishing dies, molds, tools, B tubing, channels Cleaning Smoothing metal plastic and wood Finish prior to painting or plating
1-"
"
1"
25,000
1-"
25,000
2"
"
1"
25,000
Coated
2"
25,000
2-"
1"
23,000
3"
"
1"
23,000
NOTE
Stems must be fully inserted into chuck or collet and tightened securely.
3"
23,000
1/4" Stem - Aluminum Oxide A price line designed to provide fast cutting action. Ideal for low to medium production environments. Dia. 1" Width 1" Grit Size 60 80 120 60 80 120 60 80 120 Max. RPM 30,000 Part No. 30720 30721 30722 30723 30724 30725 30726 30727 30728
6"
1"
1"
2"
1"
25,000
6"
1-"
1"
3"
1"
23,000
6"
2"
1"
Part No. 53166 53167 53169 53285 53286 53287 53289 53305 53306 53307 53309 53325 53326 53327 53329
6,000
6,000
6,000
Metal Adapters
for Unmounted Flap Wheels Used in pairs and priced per pair. Wheel Arbor Hole Size 1" 1" 1" Adapted Arbor Hole Size " 5/8" " Part No. 03833 03834 03835
2"
1"
25,000
3"
1"
20,000
www.oki-bering.com
435
Blending Discs
Coated
1-"
2"
3"
Do not exceed the maximum RPM of the back-up pad. (Speed-Lok TS is a registered trademark of Norton Co.)
Blending Discs
Dia.
- Plastic Button Style Compatible with 3M Roloc back-up pads Grit Size 36 60 80 120 36 60 80 120 Part No. Aluminum Oxide 60118 60121 60122 60124 60131 60134 60135 60137 Dia. 2" 3"
2"
3"
Do not exceed the maximum RPM of the back-up pad. (Roloc is a trademark of 3M.)
436
www.oki-bering.com
Trim-Kut Discs
Abrasives and Industrial Brushes
Trim-Kut Discs
Trim-Kut Discs
Dia. 3"
- Aluminum Oxide Grit Size 36 60 120 Max. RPM 21,000 Part No. 59300 59305 59315
Weiler's Trim-Kut Discs are abrasive discs designed for light grinding and blending applications on a variety of materials. The abrasive grains are fused directly on to a wearable polymer backing, resulting in a disc that requires no back-up pad. The polymer backing trims during use to expose new grains to the work surface. 3" discs are designed for use on drills or right angle air die grinders, and 4-" discs are for use on right angle grinders.
Arbor Hole
5/16"- 18
Coated
Do not use Trim-Kut discs in temperatures lower than 48 fahrenheit. Store at 50% relative humidity.
Trim-Kut Adapters
Description For Use With 3" Trim-Kut Discs 3" Trim-Kut Discs 4-" Trim-Kut Discs
8
Part No. 59327 59326 56485 56496
" Mandrel
3/8"-24 UNF Adapter
Adapting Nuts
TIP
Chamfering the edge of a steel pipe. Applications Edge blending Deburring Preparation for painting and surface finishing Light weld and stock removal Tool Trim-Kut Steel Disc scrap
Spanner Wrench
Extend disc life 2-3 times. Renew Trim-Kut's sharp cutting edge by running the edge against a clamped piece of steel scrap.
If you are using a blending disc or Trim-Kut Disc, ask our Application Engineering Department if Weiler's BobCat Abrasive Flap Discs can enhance your productivity. BobCats dramatically outperform blending and Trim-Kut Discs by reducing changeovers and providing consistently high cut rates and extended life.
www.oki-bering.com
437
Portable Belts
Size (Width x Length) 3" x 18" Grit Size 60 80 120 40 50 60 80 100 120 36 40 50 60 80 100 120 60 80 120 60 80 100 120 36 40 50 60 80 100 120 Part No. Zirconium 69005 69006 69007 69008 69040 69041 69042 69043 69044 69148 69149 69150 69151 69152 Aluminum Oxide 67488 67489 67491 67504 67505 67506 67507 67508 67509 67539 67540 67541 67542 67543 67544 67545 67614 67615 67617 67632 67633 67634 67635 67647 67648 67649 67650 67651 67652 67653
Coated
3" x 21"
" x 18"
Blending a weld using a portable file belt. Applications ecorative finishing of metal D surfaces Grinding, deburring and flash removal on saw-cut parts Edge blending Cleaning Smoothing metal, plastic and wood emoving tool mark and R forging scale inishing prior to painting or F plating Grinding gates off castings 3" x 24"
" x 24"
3-" x 15-"
" x 20-"
4" x 21-"
1" x 12"
4" x 24"
1" x 30"
438
www.oki-bering.com
1"
Coated
1-"
Polishing the O.D. of a part turned in a lathe. Applications Off-hand polishing of metal surfaces Cleaning stock which is being turned in a lathe General purpose machine shop use Off-hand deburring
TIP
Use light machine oil with shop rolls as a lubricant for finer finishes and quicker cut.
2"
Cutting
Type 27 Products:
Type 27 Wheels are offered in .045", .060" and 3/32" wheel thicknesses. Diameters range from 4" to 9" and are available in aluminum oxide or zirconium grain, with a choice of a 5/8"-11 hub. Wheel Selection Guide Grain A luminum Oxide: for general purpose use on all metals except titanium A C ilicon Carbide: for cutting non-metallics and titanium S (Type 1 only) CA ombination Silicon Carbide/Aluminum Oxide: for cutting ductile C iron and non-ferrous metals (Type 1 only) TA reated Aluminum Oxide: for extended wheel life and improved perforT mance of large diameter wheels in coarser grits (Type 1 only) Z Zirconium: for higher cut rates in high pressure applications (Type 27 only) Grit 24 Coarse: for fast, aggressive cutting and maximum wheel life 30 Medium/Coarse: for fast cutting and long wheel life 36 Medium/Coarse: excellent for general purpose cutting 46 Fine/Medium: for a smoother finish and reduced burr 60 Fine: for a burr-free cut Grade T-V Hard: for maximum wheel life R edium/Hard: for cutting large cross sections and improved rate M of stock removal P edium: for cutting very large cross sections and applications deM manding very rapid stock removal N Soft/Medium: for maximum cut rate
Type 1 Products:
This product category includes wheels ranging from 1- " to 14" diameters, in various grit sizes, and aluminum oxide and silicon carbide abrasive grains. Type 1 Wheels are for use on electric or air die grinders, tool room grinders, circular saws, stationary machines, portable gas or electric saws and chop saws.
Safety
Abrasive users and others in area must wear goggles or face shields over safety glasses. Safety guards must be used. Do not exceed maximum RPM.
www.oki-bering.com
439
Weiler's Hand Pads are for cleaning and conditioning surfaces by hand. Unlike steel wool, the hand pads are non-metallic, and do not produce after-rust on worksurfaces. Hand pads can be used in wet applications.
Non-Woven
Cleaning a sink in a restaurant with a commercial hand pad. Applications Hand Pads (Industrial): roducing satin finishes on aluminum and stainP less steel Light deburring Surface preparation Blending light scratches Removing rust and oxidation Hand Pads (Commercial): Cleaning and removing stains from stainless steel Removing rust and corrosion
2"
3"
4"
Do not exceed the maximum RPM of the back-up pad. (Roloc is a trademark of 3M.)
448
www.oki-bering.com
3"
5" x 5/8"-11 Arbor Hole 6" x 5/8"-11 Arbor Hole 7" x 5/8"-11 Arbor Hole
Non-Woven
51578
8" x 5/8"-11 4,500 51579 Arbor Hole Do not exceed the maximum RPM of the back-up pad.
6"
7"
8"
Brushing Guide
Industrial Brushes
Wire Brushes vs. Abrasive Wheel
Power brushing removes dirt, contaminants and oxides from base material, not the base material itself. In some applications, hard abrasive wheels will remove the base material while removing the unwanted top layer.
Base Material
Correct
Abrasive Wheel
Safety Guide
No. 1 Safety Goggles
Safety goggles or full face shields worn over safety glasses with side shields must be worn by all operators and others in the area of power brush operations.
No. 3 Guards
Keep all machine guards in place.
Observe all speed restrictions indicated on brushes, containers, labels or printed pertinent literature. MSFS, Maximum Safe Free Speed should not be exceeded under any circumstances.
www.oki-bering.com
449
Safety Information
Safety Information
Safety Goggles Safety goggles or full face shields worn over safety glasses with side shields MUST BE WORN BY ALL OPERATORS AND OTHERS IN THE AREA OF BRUSH AND ABRASIVE OPERATIONS. Comply with the requirements of ANSI Z87.1 Occupational Eye and Face Protection. Guards Keep all machine guards in place. Speeds Observe all speed restrictions indicated on brushes, abrasives, containers, labels, or printed in pertinent literature. MSFS means Maximum Safe Free Speed (RPM)spinning free with no work applied. For reasons of safety, MSFS or Maximum RPM should not be exceeded under any circumstances. Protective Equipment Appropriate protective clothing and equipment must be used where there is a possibility of injury that can be prevented by such clothing or equipment. Tool/Work Rest On bench grinders and pedestal machines, tool/work rests should be used to support the work-piece during use. It should have a maximum opening of 1/8" to the product face. Only adjust the rest when the product is not in motion. Safety Standards Comply with the Safety Standards of the American National Standards Institute Standards ANSI B165.1 Safety Requirements - Power Brushes and ANSI B7.1 Safety Requirements - For the Use, Care and Protection of Abrasive Wheels.
These icons illustrate the power tools used to drive Weiler brushed and abrasives.
Straight Grinder
Bench/Pedestal Grinder
Die Grinder
Chop Saw
Circular Saw
Drill Press
Based on the collective experience of the ABMA Industrial Division members (ANSI B165.1) and the United Abrasives Manufacturers Associations Bonded Division (ANSI B7.1), both ANSI Standards are referenced and provided solely as a public service for the guidance of the users of the members products. All Brush and Abrasive recommendations are not necessarily complete with respect to any particular application and common sense safety considerations should be adhered to generally. Any applicable federal, state, local law or regulation must be strictly adhered to and is controlling over any recommendation contained herein. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. Contact The American National Standards Institute (ANSI), 1430 Broadway, New York, NY 10018.
This warranty is expressly in lieu of all other warranties, expressed or implied, including the warranties of merchantability and fitness for a particular purpose. Correction in the manner provided hereinabove shall be the extent of Weiler's liability, and no other entity is authorized to extend that liability.
www.oki-bering.com
453
See chart below for the most effective brush or abrasive product type based on surface finish and degree of aggression required for your application. As indicated, coated and bonded abrasives will remove base material. Wire Brushes, Nylox Brushes and Non-Woven Abrasives will NOT typically remove base material and are used for jobs requiring surface refinement.
LESS
SURFACE REFINEMENT
Nylox Abrasive Nylon Filament Brushes Non-Woven Abrasives Crimped Wire Brushes Knot Wire Brushes
AGGRESSION
METAL REMOVAL
8
MORE
COURSE
SURFACE FINISH
FINE
This resin fiber disc did not work very long before the grains became loaded with material.
This power brush, however, can keep on working without ever becoming loaded with material.
454
www.oki-bering.com
Product Attributes
Brush Terminology
Wheel Brushes: Diameter Thickness Through Arbor Hole Thickness at Face Plate
Fill Materials
Steel Wire: Heat-treated, high-tensile steel wire, drawn to exacting Weiler specification, is used in all Weiler brushes with a wire diameter of .008 and above. This wire provides superior fatigue resistance and excellent brushing action. Hard Drawn Wire: Generally used in .003, .005 and .006 wire diameters for fine surface work. Stainless (Type 302) Wire: Highly corrosion resistant. Recommended where contamination or "after rust" is a problem, such as brushing stainless steel or non-ferrous metals. All Weiler stainless steel brushes are made with Type 302 stainless steel wire. Non-Ferrous: Brass, Bronze and Aluminum are some of the non-ferrous wires available in Weiler power brushes for special applications. Animal: Horsehair - A very durable material. The tail hair is stiff and the mane hair is soft. It can be blended with other materials such as synthetics. Used in a variety of brushes for scratch-free cleaning. Goat hair - This soft material is mainly used in our miniature brushes for polishing. Natural: Tampico - Produced from the stem of the Mexican agave plant. Its texture is soft to medium with good durability. Used for scrubbing and washing applications. It is heat, alkali and acid resistant. The natural color is off-white but it may be dyed or bleached. Synthetic: Nylon - Resistant to most acids and alkalis. Long wearing nylon has the greatest use in cleaning applications. It is available straight or crimped. Polypropylene - Available in strip brushes. Trim Length Cup Brushes: Arbor Hole
Arbor Hole
Overall Len
gth
www.oki-bering.com
455
Weiler's complete line of stainless steel brushes are made using Type 302 stainless steel wire. This wire was developed to provide long brush life and corrosion resistance. Using a stainless steel brush when brushing aluminum, stainless steel and other high strength alloys eliminates the danger of after rust. When these alloys are brushed with carbon steel wire, a deposit of carbon material remains which can cause rust. Type 302 brush wire is austenitic. Once a stainless steel brush has been used on carbon steel, it should never be used on stainless steel since rusting can occur. To avoid contamination, all stainless brushes should be stored away from areas (such as steel work benches) where carbon steel particles might come in contact with the brush.
Brushing Pressure
Avoid excessive pressure when using a wire brush. Excessive pressure causes over-bending of the filaments and heat build-up resulting in filament breakage, rapid dulling and reduced brush life. Instead of greater pressure, try the following: brush with more aggressive action (increase filament diameter, decrease A trim length, different brush type, i.e.: knot type instead of crimped type) Higher surface speed (increase RPM or brush diameter) Important Note: Never exceed the recommended Maximum Safe Free Speed or RPM rating of the brush.
Correct
Incorrect
Important: When running a wire brush, a rule of thumb is to run it a mile a minute or a minimum of 5,000 Surface Feet Per Minute (SFPM). Normally, higher surface speeds result in faster cycle times and longer brush life. However, never exceed the Maximum Safe Free Speed (MSFS) or RPM of the brush. Example: A 6" diameter wheel running at 3,450 RPM has a surface speed of 5,400 SFPM.
456
www.oki-bering.com
"
5/8"
Note: This chart is based on 1" brush face. Select a brush which is compatible with the horse power of the machine (see chart above). Select the largest diameter brush which will fit on the machine with all guards in place.
Conversion Charts
(Inches to Millimeters; 1"=25.4mm, 1mm=.03937") Brush Diameter Inches Millimeters 2-" 3" 3-" 4" 5" 6" 7" 8" 10" 12" 14" 15" 16" 70mm 76mm 89mm 102mm 127mm 152mm 178mm 203mm 254mm 305mm 356mm 381mm 406mm Arbor Hole Size Inches Millimeters "
3/8"
8
Brush Face Width Inches Millimeters
1/8"
6.4mm 9.5mm 12.7mm 15.9mm 19.0mm 22.2mm 25.4mm 28.6mm 31.8mm 38.1mm 44.5mm 50.8mm
3.0mm 6.4mm 9.5mm 12.7mm 15.9mm 19.0mm 22.2mm 25.4mm 28.6mm 31.8mm 38.1mm 50.8mm
"
3/8"
"
5/8"
"
5/8"
"
7/8"
"
7/8"
Product Selection
Crimped vs. Knot Wire Brushes
Crimped Wire Brushes: Made of heat-treated wire which is crimped to allow individual filaments to support each other. Provide flexibility for light to medium duty brushing action. Use on parts that could be damaged by the impact of a knot brush. Use for a broad range of applications. Knot Wire Brushes: Made of heat-treated straight wire filaments twisted as a single unit like a piece of cable or wire rope. Provide less flexibility and more aggressive brushing action in heavy-duty applications. Use on parts requiring high-impact action. Use to remove large burrs and heavy contamination, such as multiple layers of rust, scale, paint or oxides.
Knot Configurations
Standard Twist: A slight tuft at the end of the wire knot provides some flexibility for use on irregular surfaces. Cable Twist: The wire is tightly twisted to the end of the knot, providing very aggressive brushing action. Stringer Bead Twist: The wire is very tightly twisted to the end of the knot, creating a narrow face with high-impact action, primarily used for weld cleaning.
www.oki-bering.com
457
Product Selection
Trim Length Fill Density
High Density Brushes produce faster brushing action, longer brush life and finer surface finishes.
Long Trim Brushes are more conformable and are able to follow contoured surfaces.
Short Trim Brushes are faster acting and suited for more severe brushing action.
Low Density Brushes offer greater flexibility for surface cleaning operations on irregular surfaces.
8
Wire Size
It is recommended to use: Very Fine to Fine Wire for light-duty applications Medium to Coarse Wire for heavy-duty applications To maximize brush life, always use the finest wire which will accomplish the job. Wire Gauge # Dia. in Inches Dia. in mm Coarse 20 .035 0.89 24 .023 0.58 Medium to Coarse 25 .020 0.51 30 .014 0.36 Medium 33 .0118 0.30 34 .0104 0.26 Fine 35 .0095 0.24 38 .008 0.20 Very Fine 43 .006 0.15 47 .005 0.13
Wire sizes in decimals of an inch are shown in all tables. American Steel Wire Equivalent Gauge (Formerly Washburn & Moen)
Cleaning Surface Prep Roughening Weld Cleaning Remove Oxides & Rust SG, RAG, BPG SG, RAG, BPG BPG BPG RAD, SDG RAD, SDG RAG, SG, RAG, SDG, BPG HDP SDG RAG Right Angle Grinder SG Straight Grinder
Heavy Deburring
Deflashing
SG, BPG RAG RAG RAD, SDG RAD, SDG RAG, SG, RAG, SDG HDP SDG BPG Bench/Pedestal Grinder RAD Right Angle Die Grinder HDP SDG SDG Straight Die Grinder HDP Hand Drill/Drill Press BPG
RAG, BPG
458
www.oki-bering.com
www.oki-bering.com
459
Dia. 4"
Wire Size .006 .0118 .014 .006 .008 .0118 .014 .006 .0104 .0118 .014
Arbor Hole
Face Width
Trim Length
Max. AH Avail.
Max. RPM
Ref. Code
Part No. Steel 00104 Stainless 00154 00184 01675 01705 01775 01805 -
"-3/8"
"
7/8"
"
12,500
TLN-4
6"
5/8"-
"
"
1- 7/16"
1-"
7/16"
6,000
TLN-6
5/8"
"
2-1/16"
1-"
"
6,000
TLN-8
8
Applications Cleaning rust, scale and dirt Light deburring Edge blending Roughening for adhesion Finishing for appearance Finish preparation prior to plating or painting Ideal for high production applications
*Available in Display Packaging. Add "P" to end of Item No. when placing order.
Medium Face Greater fill density and more aggressive brushing action. Can be mounted in multiples. Wire Size .0118 .014 .0118 .014 .0118 10" .014 .020 Arbor Hole 2" 2" 2"* with keyway Face Width 1" 1" Trim Length 1-1/8" 1-3/8" Thickness at Face Plates
15/16"
Part No. Steel 06070 06080 06110 06120 06150 06160 06170 Stainless 06490 06530 -
1"
1-1/8"
2"
1"
3,600
TLM-10
- Wide Face Maximum wire density and aggression, covers more surface area in a single pass. Trim Length 1-1/8" 1-5/8" 1-3/8" Thickness at Face Plates 1" 1" 1-3/8" Max. RPM 6,000 6,000 Ref. Code TL-6 TL-7 Part No. Steel 03060 03070 03090 03100 03140 4,500 TL-8 03150 03160 03190 1-7/8" 2-7/8" 1-5/8" 1-9/16" 1-11/16" 4,000 TL-10 03200 03210 3,000 TL-12 03230 03240 Stainless 03510 03520 03590 03680 -
460
www.oki-bering.com
"
5/8"
"
Metal Adapters For Medium & Wide Face Brushes. Used in pairs & priced per pair. 2"
7/8"
Face Width
5/8"
"
7/8" 7/8"
" "
7/8" 7/8"
*Available in Display Packaging. Add "P" to end of Item No. when placing order.
Part No. Steel Stainless 15463 15473 15563 15573 15677 16863 16873 16963 16973
5/8"
1"
15/16"
20,000
C-3
"
"
"
Drive Arbors
Arbor Dia. Stem Dia. Stem Length 1-1/8" 1-1/8" Length of Shaft
3/16" 3/16"
For Brushes with Max. Dia. of: 2" 4" 3" 3" 3" 2" 3"
Part No.
Unthreaded
"
3/8"
Threaded
"
3/8"
" "
7/8"
" "
3/8"
1-1/16" 1"
www.oki-bering.com
461
Dia. 3"
Trim Length
5/8"
Max. AH Avail.
Part No. Steel 08004 08014* 08024 08034 08044* 08064 08075 08085* 08095 08105 08975 08835 08125 08135 08145 08155 Stainless 08254 08264 08274 08284 08294 08314 08325 08345 08375 08395
"-3/8" 20 "-3/8" 24
" "
4"
"
7/8"
7/16"
20,000
ST-4
6" 6" 7" Removing rubber coating from a hydraulic hose. 8"
5/8"-"
24 30 24 38
"
5/8" 5/8"
9/16"
5/8"-" 5/8"
5/8" 9/16"
5/8"
5/8"
"
Applications emoving rust, scale, weld R spatter and oxidation Roughening surfaces emoving rubber or plastic R flash Heavy burr removal Heavy-duty cleaning operations Weld cleaning Surface conditioning Coating removal
*Available in Display Packaging. Add "P" to end of Item No. when placing order.
Part No. Steel 09104 09134 09160 09180 09410 09430 09480 09490 09510 09530 09540
"-3/8" "-3/8"
2" 2" 2"
" "
7/8"
" "
7/8"
1" 1-"
1" 1-"
Max AH Avail.
"-3/8" 5/8"-"
5/8"
"
3/8"
1-3/8" 1-5/8"
" 1-"
2"
"
"
462
www.oki-bering.com
Dia. 10"
8
Part No. Steel 08756 09856 08766+ 09400* 08775 08776* 08916* 09386 09000*T 09100 Stainless 08806 09866 08786+ 09500 08796 08926 09396 09200T
Dia. 5" 5" 6" 6" 6" 6" 6" 6-7/8" 6-7/8"
No. of Knots 38 24 38 56 24 30 30 56 72
Face Width
3/16"
Trim Length
7/8" 7/8"
Max. RPM 12,500 12,500 12,500 12,500 12,500 12,500 12,500 9,000 9,000
Ref. Code STB-538 STB-524 STB-620 STB-6 STB-623 STB-630 STC-6 STB-756 STB-772
"
3/16" 3/16"
" "
5/16" 3/16" 3/16"
"
7/16" 7/16"
+Light Duty T Patented Note: This product has " face width. *Available in Display Packaging. Add "P" to end of Item No. when placing order.
No. of Knots 32 56
Face Width
3/16" 3/16" 3/16" 3/16"
Trim Length
7/8"
www.oki-bering.com
463
Arbor Hole
Part No. Steel 14016 14026 14036* 14206 14216 14066+ 14076*+
1-" 1-"
8,000 6,600
CR-5 RCR-6
Removing paint from a metal surface with a crimped wire cup brush.
*Available in Display Packaging. Add "P" to end of Part No. when placing order. +With internal nut.
Trim Length
7/8"
Trim Length 1-" 1-" 1-" 1-" 1-3/8" 1-3/8" 1-3/8" 1-5/8"
Max. RPM 9,000 10,200 10,200 10,200 7,000 6,600 6,600 6,000
Ref. Code SR-3 SR-4 SRC-4 RSR-4 RSR-5 SR-6 RSR-6 SRF-6
Part No. Steel 12736 12746 12306 12316 12326 12206 12826* 12256* 12276 * 12356+ 12376 + 12396+ 12816 * 12846+ 12856+ 12866+
/8"-11 UNC
464
www.oki-bering.com
Knot Wire Cup Brushes - 1-" Rows - For line traveling machines.
Dia. 4" 6" Wire Size .023 .030 Arbor Hole
5/8"-11 UNC 5/8"-11 UNC
Part No. Steel 12756 12766 12536* 12556* 12576* 12906* 12916* 12926*
5/8"-11 UNC
6"
5/8"-11 UNC
1-"
6,000
DRF-6
* Patented
8
Part No. Steel 12796 12676 12686
Trim Length
7/8" 7/8"
Trim* Length
5/8" 7/8"
Std. Pkg. 1 1
No. of Knots 20
Face Width
3/8"
Trim Length
5/8"
Part No. Steel 13201 13100 13101 13102 13103 13105 13106* 13114 13116 13119 13120 Stainless 13208 13107 13108 13109 13110 13112 13113*
Weilers Mighty Mite Brushes are specifically designed for smooth, yet aggressive brushing action on small angle grinders.
4"
.014
M10 x 1.25 M10 x 1.50 M14 x 2.0 3/8"-24 UNF "-13 UNC 5/8"-11 UNC M10 x 1.25 M14 x 2.0 "-13 UNC 5/8"-11 UNC
24
"
7/8"
7/16"
20,000
STA-4
4"
.020
24
"
7/8"
7/16"
20,000
STA-4
* Available in Display Packaging. Add "P" to end of Item No. when placing order.
www.oki-bering.com
465
AEG
Makita
Bosch
Metabo
DeWalt
Hilti
Hitachi
Porter Cable
Ingersoll-Rand
Ryobi
Sioux
Jepson
Skil
Jet
466
www.oki-bering.com
Mighty-Mite Brushes
Max. RPM
Ref. Code
4"
.020
24
"
7/8"
20,000
CTA-4
*Available in Display Packaging. Add "P" to end of Item No. when placing order.
No. of Knots 32 32
Face Width
3/16" 3/16"
Trim Length
7/8" 7/8"
Part No. Steel 13124 13125* 13126* 13127 13128 13130* 13131* Stainless 08954 13132 13133 13134 13135 13137 13138*
M10 x 1.25 M10 x 1.50 M14 x 2.0 3/8"-24 UNF 1/2"-13 UNC 5/8"-11 UNC
*Available in Display Packaging. Add "P" to end of Item No. when placing order.
No. of Knots 32
Face Width
3/16"
Trim Length
7/8"
Trim Length
7/8"
Mighty-Mite Adapters
For Cup or Wheel Brushes Fixed Thread Size
5/8" - 11 UNC 5/8" - 11 UNC 5/8" - 11 UNC 5/8" - 11 UNC
Adapted Thread Size M10 x 1.25 M10 x 1.50 3/8" - 16 UNC 3/8" - 24 UNF
* vailable in Display Packaging. Add "P" to A end of Item No. when placing order.
Face Width
1/2"
Trim Length
7/8"
www.oki-bering.com
467
Mighty-Mite Brushes
Trim Length
Part No. Steel Stainless 13401 13402 13403 13406 13421 13422 13423 13426 13451 13452 13453 13456 13471 13472 13473 13476 13411 13412 13413 13416 13431 13432 13433 13436 13461 13462 13463 13466 13481 13482 13483 13486
4"
"
.020
20
3/8"
"
12,500
.014
20
3/8"
1"
12,500
8
4-" .020
20
3/8"
1"
12,500
2-"
.014
1"
14,000
SRA-2
2-"
.020
1"
14,000
SRA-2
3-"
.023
7/8"
13,000
SRA-3
*Available in Display Packaging. Add "P" to end of Item No. when placing order.
468
www.oki-bering.com
3"
.014
1"
14,000
CRA-2
3-"
.014
7/8"
12,000
CRA-3
*Available in Display Packaging. Add "P" to end of Item No. when placing order.
"
"
"
7/8"
25,000
EBA-20
7/8"
22,000
EBA-21
Applications
leaning and finishing recessed areas C or I.D.s Die, mold and tool cleaning and polishing Rubber and plastic flash removal Rust and paint removal Scale and slag removal I.D. pipe cleaning Carbon cleaning Weld cleaning Deburring Spot facing
1"
*Available in Display Packaging. Add "P" to end of Part No. when placing order.
www.oki-bering.com
469
Stem-Mounted Brushes
Dia.
Trim Length
7/8" 7/8"
"
1-1/8"
* Available in Display Packaging. Add "P" to end of Item No. when placing order.
Trim Length
Part No. Steel 17609 17610 17615 17616 17617 Stainless 17611 17618
"
1"
"
20,000
CFX-3
" "
1"
"
7/16" 15/16"
Trim Length
5/8"
4"
"
7/8"
20,000
STM-4
"
7/8"
470
www.oki-bering.com
Double Stem, Double Spiral Use with power tools for heavy-duty cleaning and deburring. Dia.
5/8"
Stem Dia.
7/32"
Part No. Steel Stainless 21109 21110 21247 21111 21115 21119 21121
"
1"
" "
Nylon Tube Brushes Loop Handle, Straight Black Nylon Fill Dia. Fill Dia. .005 .005 .010 .012 .014 .014 .014 Brush Part 2" 2" 3" 3" 4" 4" 5" Stem Dia.
3/32" 3/32" 1/8" 1/8" 5/32" 5/32" 3/16"
"
Crosshole deburring an aluminum manifold. Applications eburring and cleaning drilled holes D and internal threads Cleaning and finishing internal diameters of pipes and tubes eburring and cleaning internal D keyways and grooves Carbon removal Crosshole deburring
3/8"
" "
1" 1-" 2"
www.oki-bering.com
471
Floor Brushes
Fine Sweeping
Lacquered hardwood block - For dust and fine dirt on smooth surfaces; tile, linoleum, wood. Block size: 24" Trim: 3" Part No.42002- Black horsehair fill Part No.42042- Flagged silver polystyrene fill (Not for use with sweeping compounds).
Medium Sweeping
Lacquered hardwood block - For general purpose sweeping on semi-smooth surfaces; wood, smooth concrete. Black tampico fill Block size: 18" or 24" Trim: 3" Part No.42007- 18" Part No.42008- 24"
Lacquered hardwood block - For heavy, caked dirt and debris on concrete and other rough surfaces. Solvent, oil, chemical and liquid resistant. Wet or dry applications. Block size: 24" Trim: 3-1/4" Part No.42026
Industrial Accessories
Heavy-duty metal tip provides additional strength. Diameter: 15/16" Length: 60" or 72" Part No.44300- 60" Part No.44302- 72"
Handle Accessories
Steel brace that reinforces and locks handle to block. (Standard with sweeps 30" and larger) Fits all handle sizes. Part No.44021 Heavy-duty steel brace attaches to block with wood screws and wraps around handle. Increases life of the brush by providing extra support for handle and block. Fits all handle sizes. Part No.44290 Heavy-duty steel brace (Part No. 44290) provides extra support.
12
Synthetic Duster
Brush Length 8" Block Type Wood
Dust Pans
Heavy-duty 20 gauge steel. Black enamel finish.
Description Shop dust pan standard width Shop dust pan extra wide
www.oki-bering.com
603
Miscellaneous Brushes
Vehicle Wash Brushes
Protective bumper - Foam block with two handle holes. Can be used with flow-through handle #44319. Part No. 44510 73146 Block Size 9-1/2" x 2-3/4" Fill Material Flagged white polystyrene Flagged green polystyrene Trim Length 2-1/2" Part No. 44032 44031 44448 Block Size 7" 6-1/2" 6-1/2"
Masonry Brushes
Useful tools for applying cement, waterpaints and liquid waterproofing materials on cement block and other masonry walls. Handle attached. Fill Material White tampico No. of Rows 2 4 5 Trim Length 3-1/4" 3-1/2" 4"
For general scrubbing in factories, kitchens, institutions, etc. Part No. 44013 44014 44016 44017 Overall Length 8" 20" Fill Material Yellow polypropylene White tampico Yellow polypropylene White tampico Trim Length 2"
Whitewash Brush
Two tapered handle holes allow user to choose the correct brush angle needed. Part No. 44034 Block Size 7" Fill Material White tampico Trim Length 2-5/8" No. of Rows 2
Industrial Accessories
For internal cleaning and deburring of copper tube fittings. Also used in trucking and marine industries as a light socket cleaning brush. Brush Length: 1" Diameter Part No. Ref. Code Handle Length: 3-1/4" Brush Tube Overall Length: 6-1/2" 44078 CF-18 1/4" 1/8" 44079 CF-28 3/8" 1/4" 44080 CF-38 1/2" 3/8" 44081 CF-48 5/8" 1/2" 44082 CF-58 3/4" 5/8" 12 44083 CF-68 7/8" 3/4" 44084 CF-78 1" 7/8" 44085 CF-88 1-1/8" 1" 44086 CF-128 1-3/8" 1-1/4" 44087 CF-148 1-5/8" 1-1/2"
Std Pkg 36 24 12 12
Acid/Flux Brushes
Horsehair - Tin ferrule Trim Length: 3/4" Overall Length: 5-3/4"
White Bristle w/ wooden handle Economy brushes provide lasting, efficient service at Part No. minimal cost. 40065 Part No. Ref. Code Width 40066 44088 AB-1 5/16" 40067 44089 AB-2 3/8" 40068 44090 AB-3 1/2" 40069 Weiler's Wall, Varnish and Sash Brushes come in a wide 40070 variety of sizes and materials to fill all applications. 40071
604
www.oki-bering.com
Scratch Brushes
Scratch Brushes
Curved Handle Scratch Brushes
Brush Length 5-" 6" 5-" 6" 5-" 6" No. of Rows 3 x 19 4 x 18 3 x 19 4 x 18 3 x 19 4 x 18 Hardwood Handles - For all types of dirt and rust removal. Ideal for removing rust, scale and paint from metal surfaces. Block Size 14" x 7/8" 14" x 1-1/8" 14" x 7/8" 14" x 1-1/8" Trim Length 1-3/16" 1-3/16" 1-3/16" 1-3/16" 1-3/16" 1-3/16" Ref. Code CH-39 CH-48 CH-39SC CH-48SC CH-39SS CH-48SS Part No. 44053 44056 44055 44058 44054 44057
Economy brushes provide lasting, efficient service at minimal cost. Trim Length 1" 1" 1" 1" Ref. Code ECH-39 ECH-48 ECH-39SS ECH-48SS Part No. 25150 25201 25154 25202
Industrial Accessories
Hardwood Handles - For removing dirt and rust from pipe threads, welds and metal castings. Block Size 10" x 5/8" 10" x 1-1/8" 11" 10" x 3/8" 10" x
5/8"
Economy brushes provide lasting, efficient service at minimal cost. Trim Length 1" 1" Ref. Code ESH-46 Part No. 25100
Steel wire (.012 diameter) 10" x 1" 5" 4 x 16 Stainless steel wire (.012 diameter) 10" x 1" 5" 4 x 16
ESH-46SS 25104
"
1-3/16" 1-3/16" 1-3/16"
12
10" x 1-1/8"
Trim Length
Part No. 44075 44167 44189 44637 95013 95014 44251 44619 99383
"
2x9
5/8"
"
www.oki-bering.com
605
Scratch Brushes
Scratch Brushes
Heavy-Duty Scratch Brush with Scraper
Steel wire (.012 diameter) Block Size 11-" x 1-" Brush Length 5-" No. of Rows 4 x 11 Trim Length 1-" Ref. Code SC-41 Part No. 44069
Industrial Accessories
11-" x 1-"
Platers Brushes
Hardwood Block. For general cleaning in the plating, metal finishing, aircraft and missile industries. Also used with inert arc aluminum welding. Block Size 13" x 7/8" 10" x 1-1/8" 13" x 1-1/8" Brush Length 5-" 5" 5-" No. of Rows 3 x 19 4 x 18 4 x 19 3 x 19 4 x 18 Trim Length 1" 1" 1" 1" 1" Ref. Code PCH-39 PCH-46 PCH-48 PCH-39-B PSH-46-B Part No. 44660 44240 44232 44118 44119
12
606
www.oki-bering.com
Specialty Rollers
Can be used with all paints. Ideal for trim and touch-up. Coating Enamels, epoxies, adhesives, paint All paint All paint Description 3" Roller with
3/8"
Work Surface Material Metal, smooth wood, smooth concrete Rough wood, drywall, cement block Stucco, brick, concrete
Part No. nap. Wire frame with two tin end caps. Bent wire handle 49015
(Low nap)
49024
Industrial Accessories
Nap
3/8"
Paint Trays
Description 9" Galvanized steel tray; (1 qt. capacity), rust resistant Part No. 49010
Economy Roller
Poly blend with treated paper core. Size 9" Nap
3/8"
12
Painting Surface Semi-smooth Part No. 49070
Bucket Grid
Permits use of paint roller directly from 5-gallon pail. Description Heavy steel - 5 gallon size Part No. 49007
Frames
All metal with two plastic caps. Solid plastic handle with threaded grip. Size 3" 4" 9" 9" Description Standard-duty " diameter frame with 4 wire cage Standard-duty " diameter frame with 4 wire cage Standard-duty " diameter frame with 4 wire cage Heavy-duty 5/16" diameter frame with 5 wire cage Part No. 49019 49018 49020 49022
Painter's Mitt
Can be used with all types of paint. Made of lint-free synthetic with protective plastic liner. Use on pipes, rails, fences and hard-to-reach areas. Description Painters Mitt Part No. 49005
www.oki-bering.com
607