Online - 2455-3891
Print - 0974-2441
Vol 12, Issue 3, 2019
Research Article
PIPERACILLIN ESTIMATION BY ION-ASSOCIATIVE COMPLEX FORMATION
GIRI PRASAD GORUMUTCHU1, VENKATA NADH RATNAKARAM2*, KIRAN KUMAR KATARI3
1
Department of Chemistry, Acharya Nagarjuna University, Nagarjuna Naga, Andhra Pradesh, India. 2Department of Chemistry, GITAM
University, Bengaluru, Karnataka, India. 3Department of Chemistry, Kakarparthi Bhavanarayana College, Vijayawada, Andhra Pradesh, India.
Email: doctornadh@yahoo.co.in
Received: 23 October 2018, Revised and Accepted: 23 November 2018
ABSTRACT
Objective: The objective of the study was to develop a simple, validated, and affordable visible spectrophotometric method for determination of
piperacillin (PIP) present in bulk and powder for injection formulation.
Methods: In the present method, cobalt thiocyanate (CTC) was used as a chromogenic reagent where it forms 2:1 ion pair complex at pH 2 with PIP
which is having secondary and tertiary amine groups.
Results: The formed bluish-green colored ion pair between PIP and CTC is quantitatively extractable into nitrobenzene with an absorption maximum of
665 nm. Regression analysis (r=0.9996) shows that the plotted calibration curve exhibits good linearity in the studied range of concentration (3–18 µg/mL).
Low values of relative standard deviation (<2%) were observed indicating that the proposed method is reproducible, accurate, and precise.
Conclusions: As per the existing guidelines of ICH (international council for harmonization of technical requirements for pharmaceuticals for human
use), various parameters of the proposed method were tested for validation and can be used method of choice for routine analysis in industrial quality
control laboratories, especially in developing countries.
Keywords: Validation, Piperacillin, Cobalt thiocyanate, Ion pair extraction, Assay.
© 2019 The Authors. Published by Innovare Academic Sciences Pvt Ltd. This is an open access article under the CC BY license (http://creativecommons.
org/licenses/by/4. 0/) DOI: http://dx.doi.org/10.22159/ajpcr.2019.v12i3.29289
INTRODUCTION
Piperacillin (PIP) is a semisynthetic antibiotic used for the treatment of
serious, hospital-acquired infections, and polymicrobial infections [1,2].
Its chemical structure is shown in Fig. 1. Until date, very few analytical
methods were reported for the determination of the drug individually or
in combination with other drugs using techniques such as LCMS/MS [3,4],
HPLC MS/MS [5], HPLC [6-12], and ultraviolet (UV) [13-16]. However, no
analytical method is available in literature for the determination of PIP
using visible spectrophotometry. Hence, an extractive ion pair complex
formation method is proposed in the present study for determination of
PIP by visible spectrophotometry.
MATERIALS AND METHODS
Standard PIP solution
It was prepared by accurately weighing about 100 mg of in 100 mL
volumetric flasks separately. Then, the drugs were dissolved with
25 mL of methanol and sonicated to dissolve it completely and made up
to the mark with the same solvent. The contents were mixed well and
filtered through Ultipor® Nylon 6,6 membrane. Standard stock solution
concentration of 1000 µg/mL was obtained.
RESULTS AND DISCUSSION
Absorption spectrum of colored complex
A characteristic absorption maximum was observed at 665 nm
for the developed chromophore in determination of PIP by visible
spectrophotometry (Fig. 2).
All chemicals used were of analytical reagent grade, and distilled water
was used throughout the investigation. TECHOMP (UV 2310) double
beam UV-visible spectrophotometer with HITACHI software version 2.0
was used to measure the absorbance. Quartz cuvettes (10 mm path
length) were used for the analysis. Shimadzu AUX-220 balance and Elico
LI-120 digital pH meter were used to weigh the samples and to measure
pH, respectively. Spectroscopic measurements were conducted at room
temperature (25±5°C).
Preparation of reagents
Cobalt thiocyanate solution (CTC solution)
It was prepared by dissolving 7.25 g of cobalt nitrate and 3.89 g of
ammonium thiocyanate in 100 mL of distilled water.
pH 2 buffer solution
It was prepared by mixing 306 mL of 0.1 M tris sodium citrate with
694 mL of 0.1M HCl and the pH adjusted to 2 [17].
Fig. 1: Chemical structures of piperacillin
Gorumutchu et al.
Asian J Pharm Clin Res, Vol 12, Issue 3, 2019, 159-163
value of two (Fig. 4a.), indicating that protonated drug is helping the
ion-pair formation and extraction of the formed complex is maximum at
this pH. Hence, citrate buffer solution (pH 2.0) was selected for further
investigation. Formation of a single extractable complex is confirmed
from the same λmax and shape of absorption spectra in the studied pH
range. The optimum volume of buffer solution (pH 2) is found to be
4 mL (Fig. 4b).
Optimization of reactions conditions
The optimum reaction conditions for the complex formation were
established. While maintaining the constant volume of aqueous
layer (20 mL), volume of CTC solution was increased. Optimum
CTC volume was found to be 5.0 mL (Fig. 3) which may be excess
than the stoichiometric requirement in view of two reasons. CTC
itself undergoes dissociation in aqueous medium, and excess CTC
volume helps the stabilization of labile PIP - CTC complex, and hence,
quantitative complex is formed [18]. Further, CTC volume addition
leads to a decrease in the absorbance.
Benzene, chloroform, dichloromethane, nitrobenzene, and aniline were
used as extracting solvents for the complex. Nitrobenzene was found to
be the most convenient solvent as it gave the best results and the results
were stable (Fig. 5). Absorbance values were found to be reproducible
with single extraction of ion pair using 10 mL of nitrobenzene (3:2
volume ratio of aqueous to organic phase solvents) and a decreasing
trend of absorbance was observed at lower volume ratio of organic
phase.
Literature survey shows that the mixed ligand complex (formed
between cobalt, thiocyanate, and drug) decomposes at higher pH values
leading to a decrease in absorbance intensity [19]. Hence, in the present
study, the effect of variation of pH of the aqueous phase was studied
within the range of 1–4. A maximum absorbance was observed at pH
Within the studied range of shaking time (30 s to 3 min) of aqueous and
organic phases, its influence on absorbance was found to be insignificant,
and hence, 1 min shaking time was accepted. In the proposed method, the
order of addition of the optimized volumes of reagents is PIP, buffer, CTC,
water, and nitrobenzene. Equimolar concentrations of PIP and CTC were
used in continuous variation [20] method to establish the composition
of the complex, and it indicates the association of two PIP molecules with
each CTC. It is also supported by molar ratio method [21]. Accordingly,
the chemical reaction involved in the formation of colored complex can
be shown as CTC+2 PIP → (CTC) (PIP)2. The developed color is found be
stable for minimum 24 h at room temperature.
Chromophore formation and chemistry
Organic analytes possessing positive charge can be determined using
thiocyanate complexes having metal ions such as Cr(III), Fe(III), Co(II),
and Zn(II) by different techniques like spectrophotometry, AAS and
ion selective electrodes [22]. CTC, a classical reagent is formed by the
combination of NH4SCN and cobaltous nitrate. It has been demonstrated
to be an appreciable reagent for both the qualitative detection and
quantitative determination of amino group-containing organic
compounds. Hence, CTC is used as a chromogenic reagent in the present
case. Presence of secondary and alicyclic tertiary amino groups in PIP
is exploited for its estimation by complexing with CTC at pH 2, that is,
acidic pH medium facilities the protonation of 2° or 3° amine nitrogen
atom of PIP which in turn subsequently participate in the development
of bluish-green colored ion pair complex. The formed ternary complex
comprises PIP, thiocyanate and cobalt as main ligand and second ligand,
and metal ion, respectively, with a ratio of 2:4:1 (Fig. 6). CTC ion is a
weak complex and is stabilized to some extent by the development
of ion pair with PIP. Thiocyanate is added in higher amounts than
stoichiometric requirement for further stabilization of the formed
labile ion pair complex. Extraction of ion pair into organic solvent
helps for its satisfactory stabilization and eliminates any interference
from the unreacted excess amount of thiocyanate complex as it is left
behind in aqueous phase [23]. The so-formed ion pair complex in
aqueous phase is extractable quantitatively into nitrobenzene, which
is determined by visible spectrophotometer at 665 nm. Chances of
Fig. 2: Visible spectrum of piperacillin - cobalt thiocyanate
solution ion pair complex
Fig. 3: Effect of volume of cobalt thiocyanate solution
a
b
Fig. 4: (a) Effect of pH of buffer solution and (b) effect of volume of buffer (pH 2) solution
160
Gorumutchu et al.
Asian J Pharm Clin Res, Vol 12, Issue 3, 2019, 159-163
involvement of the coordinate covalent bond between nitrogen atoms
of PIP and CTC can be eliminated based on steric hindrances associated
with amines present on drug. Moreover, the observed effect of pH on
absorbance of complex and higher absorbance in acidic pH supports
the ion pair formation. Such ion pair formation between protonated
nitrogen atom of drug (in acidic pH) and CTC due to electrostatic
attraction was reported by earlier researchers [23,24]. The entire
extraction procedure can be simply represented as PIPaq + CTC– ⇌ PIP+
CTC–aq ⇌ PIP+ CTC–org. Subscripts “aq” and “org” represent aqueous and
organic phases, respectively. Washing of the nitrobenzene extract with
water is avoided because the fragile ion pair complex may decompose
by shifting the equilibrium to the right which leads to the discharge of
color [18].
Optimized method procedure
In to a series of 125 mL separating funnels, aliquots of standard drug
solution (3–18 µg/mL) were taken. Then, added 4 mL of buffer solution
and 5 mL of CTC solution. The volume of each aqueous phase in each
separating funnel was adjusted to 15 mL with distilled water. To each
separating funnel, 10 mL of nitrobenzene was added, and the contents
were shaken for 1 min. The two phases were separated and organic layer
was collected to dry it over anhydrous sodium sulfate. The absorbance
of the organic layer was measured against a similar reagent blank.
Accuracy
Percent recovery values were determined to know the accuracy
of the proposed method. This was performed by adding different
amounts (50%, 100%, and 150%) of bulk samples of PIP to 6 μg/mL
to maintain the total amount of drug (theoretical) concentration within
the linearity range. The percentage recovery values were in the range
of 99.26–99.88 (Table 3). Low values of standard deviation (SD) and
relative standard deviation (%RSD) indicate a high level of accuracy for
the proposed method.
Precision
Three different concentrations of PIP were selected in the linear
range (3–18 µg/mL) to study intra- and inter-day precision. Each
concentration was analyzed in six independent series on the same day
and on 6 consecutive days (Table 4). % RSD values of intra- and interday studies varied in the range 0.741–1.16 and 0.71–1.06, respectively,
indicating the satisfactory precision of the method.
Ruggedness
To evaluate the ruggedness of the proposed developed method, assay
of 3, 9, and 18 µg/mL of PIP was carried out under the same optimized
conditions on different days by two different analysts. Reproducible
Table 1: Calibration values of PIP
Validation of method
Linearity and range
Concentration (µg/mL)
Absorbance*
The calibration curve was constructed by plotting a graph between
absorbance versus concentrations in the range of 3–18 μg/mL and was
found to be linear (Fig. 7). A point of the calibration graph indicates
the mean value of three independent measurements (Table 1).
y=0.0615x+0.0213 was the linear regression equation. The correlation
coefficient was >0.999, and hence, the linearity of the proposed
analytical method was tested. Table 2 represents different optical and
regression parameters.
3
6
9
12
15
18
0.206
0.384
0.587
0.753
0.945
1.128
*Average of three determinations, PIP: Piperacillin
Table 2: Optical characteristics, statistical data of the regression
equations, and validation parameters for of PIP
S. No
Fig. 5: Effect of solvent nature
Parameter
Optical characteristics
1.
Apparent molar absorptivity (L/mol/cm)
2.
Sandell’s sensitivity (µg cm−2A−1)
Regression analysis
1.
Slope
2.
Intercept
3.
Regression coefficient (r)
Validation parameters
1.
λmax(nm)
2.
Beer’s law limit (Linearity, μg/mL)
3.
Limit of detection (μg/mL)
4.
Limit of quantitation (μg/mL)
5
Stability period (hours)
Observation
3.33×104
0.0155
0.061
0.021
0.9996
665
3–18
0.35
1.0
Minimum 24
PIP: Piperacillin
Fig. 6: Formation of ion pair complex
161
Gorumutchu et al.
Asian J Pharm Clin Res, Vol 12, Issue 3, 2019, 159-163
Table 3: Recovery of PIP
Level of
recovery (%)
Nominal
concentration used
(µg/mL) (a)
Amount of
drug added
(µg/mL) (b)
Total amount of
drug (a+b) (µg/mL)
(theoretical)
Amount of drug
recovered (µg/mL)
(practical)
Statistical
evaluation
Percentage
recovery=Practical/
Theoretical×100
50
6
6
6
6
6
6
6
6
6
3
3
3
6
6
6
9
9
9
9
9
9
12
12
12
15
15
15
8.99
8.97
8.96
11.96
11.98
11.97
14.96
14.91
14.89
Mean:8.97
SD:0.012
%RSD:0.139
Mean:11.97
SD:0.008
%RSD:0.068
Mean:14.92
SD:0.029
%RSD:0.197
99.88
99.66
99.55
99.66
99.83
99.75
99.73
99.40
99.26
100
150
SD: Standard deviation, RSD: Relative standard deviation, PIP: Piperacillin
Table 4: Intra- and inter-day precision readings
Concentration of PIP (µg/mL)
3
9
18
Concentration*
Intra-day (Mean±SD) (µg/mL)
%RSD
Inter-day (Mean±SD) (µg/mL)
% RSD
2.97±0.02
9.15±0.08
17.85±0.21
0.71
0.83
1.16
2.95±0.02
9.15±0.09
17.91±0.19
0.71
1.01
1.06
*Average of six determinations, SD: Standard deviation, RSD: Relative standard deviation, PIP: Piperacillin
Table 5: Ruggedness data of PIP
Test concentration of PIP
(µg/mL-1)*
Concentration
Mean±SD (μg/mL)
%RSD
3
9
18
2.92±0.021
9.15±0.06
17.91±0.14
0.72
0.66
0.79
* Average of six determinations, PIP: Piperacillin, SD: Standard deviation,
RSD: Relative standard deviation
Table 6: Estimation of PIP from its formulation by visible
spectrophotometric method
Powder for
injection
formulation
Pipracil
Labeled
Amount found* Percentage %RSD
Amount (g) Mean±SD (g)
drug
recovered
2
1.984±0.008
99.185
0.393
*Average of three determinations, PIP: Piperacillin, SD: Standard deviation,
RSD: Relative standard deviation
results are evident as there was no significant difference between the
analysts. Hence, the proposed method is rugged (Table 5).
Detection of Limits of detection and quantification (LOD and LOQ)
LOD and LOQ were calculated to determine the sensitivity of the
proposed method based on the signal to noise ratio [25]. LOD and LOQ
for PIP were calculated from the values of S (slope of the calibration
curve) and σ (SD of the response) as per the International Council for
Harmonization guidelines (2005) [26].
LOD=3.3×σ/S=0.35 µg/mL and
LOQ=10×σ/S=1.0 µg/mL
Analysis of pharmaceutical formulations
The active pharmaceutical ingredient (API) present in the PIP powder
for injection (Pipracil®) was extracted using 0.5 M hydrochloric acid
solution, suitable volume of diluent water and sonication for 10 min.
As the recovery values of the API are good, the proposed method can
Fig. 7: Calibration graph of piperacillin
be successfully applied to the determination of PIP in pharmaceutical
formulations without any interference from common excipients. The
amount of API was determined by measuring the absorbance values of
chromophores derived from the extracts (Table 6) and using the aboveconstructed calibration curve.
Spectrophotometric method is the generally used method and of choice
for routine analysis in industrial quality control (QC) laboratories,
especially in developing countries [27-36]. Hence, the present study is
an attempt to develop a sensitive visible spectrophotometric method for
the determination of PIP in pure and powder for injection formulations
using an extractive ion pair complex-forming agent like CTC.
CONCLUSIONS
A simple visible spectrophotometric method was developed for
the quantitative estimation of PIP in pure and powder for injection
formulation based on the formation of bluish-green colored ion pair
associate with [Co(SCN)4]2- followed by its extraction into organic
solvent-nitrobenzene. Compared to less polar solvents (benzene,
chloroform, dichloromethane, and aniline), nitrobenzene is proved to
be a successful extracting solvent in view of higher solubility of ion pair
in it. The proposed method is straightforward as there is no need to
162
Gorumutchu et al.
Asian J Pharm Clin Res, Vol 12, Issue 3, 2019, 159-163
maintain complicated conditions (such as intricate sample treatment
and vigilance to maintain critical optimum pH) and can be performed
without usage of expensive or sophisticated instrumentation. All these
advantages help to encourage the proposed method in the routine
analysis of PIP (bulk drug and powder for injection formulation) in QC
laboratories, as an alternative to the HPLC and LCMS/MS methods.
AUTHORS’ CONTRIBUTIONS
Mr. Giri Prasad Gorumutchu: Experimental work, data collection, and
analysis; Prof. Venkata Nadh Ratnakaram: Study design, concept, and
manuscript preparation; Dr. Kiran Kumar Katari: Statistical analysis.
CONFLICTS OF INTEREST
Authors have no conflicts of interest to declare.
REFERENCES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Tan JS, File TM Jr. Antipseudomonal penicillins. Med Clin North Am
1995;79:679-93.
Hauser AR. Antibiotic Basics for Clinicians. 2nd ed. Philadelphia, PA:
Wolters Kluwer; 2013. p. 26-7.
Scheer F, Krämer I. A liquid chromatography assay for the simultaneous
quantification of piperacillin and ciprofloxacin in human plasma
and dialysate in critically III patients undergoing continuous renal
replacement therapy. Int J Anal Mass Spectrom Chromatogr 2014;
2:43-51.
Barco S, Risso FM, Bruschettini M, Bandettini R, Ramenghi LA,
Tripodi G, et al. A validated LC–MS/MS method for the quantification
of piperacillin/tazobactamon dried blood spot. Bioanalysis 2014;
6:2795-802.
Li Z, Li Q, Yi W, Di C, Chen C. Determination of free and total
piperacillin–tazobactam in plasma by HPLC–MS–MS an adapted
method for neonates. Chromatographia 2012;75:533-39.
Veni PR, Sharmila N, Narayana KJ, Babu BH, Satyanarayana PV.
Simultaneous determination of piperacillin and tazobactamin
pharmaceutical formulations by RP-HPLC method. J Pharm Res 2013;
7:127-31.
Pai PN, Rao GK, Murthy MS, Prathibha H. Simultaneous estimation of
piperacillin and tazobactam in injection formulations. Indian J Pharm
Sci 2006;68:799-801.
Ramalingam P, Rajendran K. Detection of stability and degradation of
piperacillin and tazobactam in injectables from in-patient wards and
pharmacy by RP-HPLC method. Gulf Med J 2014;3:S132-41.
Rao AL, Krishna KS, Ch KK, Raja T. Simultaneous determination of
piperacillin and tazobactum in bulk and pharmaceutical dosage forms
by RP-HPLC. Int J Pharm J Pharm Sci 2011;3 Suppl 2:1033-40.
Augey V, Grosse PY, Albert G, Audran M, Bressolle F. High-performance
liquid chromatographic determination of tazobactam and piperacillin
in human plasma and urine. J Chromatogr B Biomed Appl 1996;
682:125-36.
Arzuaga A, Isla A, Gascón AR, Maynar J, Martín A, Solinís MA, et al.
Quantitation and stability of piperacillin and tazobactam in plasma and
ultrafiltrate from patients undergoing continuous venovenous hemo
filtration by HPLC, Biomed Chromatogr 2005;19:570-8.
Veillette JJ, Winans SA, Forland SC, Maskiewicz VK. A simple and rapid
RP-HPLC method for the simultaneous determination of piperacillin
and tazobactam in human plasma. J Pharm Biomed Anal 2016;
131:80-6.
Sangeetha S, Kumar M, Kumudhavalli MV, Alexandar S, Jaykar B.
Development and validation of UV spectrophotometric area under curve
method for quantitative estimation of piperacillin and tazobactam. Int J
Chem Tech Res 2017;10:988-94.
Toral MI, Nova-Ramirez F, Nacaratte F. Simultaneous determination of
piperacillin and tazobactam in the pharmaceutical formulation tazonam
by derivative spectrophotometry. J Chil Chem Soc 2012;57:1189-93.
15. Xiaoping B, Yongli BX, Xiaolei W. Content determination of sodium
piperacillin and sodium tazobactam for injection by double wavelength
UV spectrophotometry. J Chin Pharm Affairs 2003;8:27.
16. Zhang AP, Bai XH, Tong LG. Determination of piperacillin in compound
injection by double wavelength ultraviolet spectrophotometry. J Shanxi
Med Univ 2004;6:15.
17. Her Majesty’s Stationery Office. British Pharmacopoeia. London, UK:
Her Majesty’s Stationery Office; 1993. p. 77.
18. Amin AS, Aly HM. Utilization of colorimetric and atomic absorption
spectrometric determination of aztreonam through ion pair complex
formation. Int J Pharm 2000;205:35-41.
19. El-Kousy N, Bebawy LI. Determination of some antihistaminic drugs
by atomic absorption spectrometry and colorimetric methods. J Pharm
Biomed Anal 1999;20:671-9.
20. Job P. Formation and stability of inorganic complexes in solution. Ann
Chim 1928;2:113
21. Yoe J, Jones A. Colorimetric determination of iron with disodium-1,
2-dihydroxybenzene-3, 5-disulfonate. Ind Eng Chem Anal Ed
1944;16:111-5.
22. Brashy EL, El-Sayed M, Abdallah MF, Sepai EL. Spectrophotometric
determination of some fluoroquinolone antibacterials by ion-pair complex
formation with cobalt (II) tetrathiocyanate. J Chin Chem Soc 2005;
52:77-84.
23. Abdel-Gawad FM, El-Guindi NM. Spectrophotometric determination
of metoclopramide and oxybuprocaine through ion pair formation
with thiocyanate and molybdenum (V) or cobalt (II). Anal Lett 1995;
28:1437-47.
24. Fekria M. Determination of amineptine and amprolium hydrochlorides
through ion associates with cobalt (II) thiocyanate. Sci Pharm 2017;
70:355-66.
25. Sethi PD. HPLC Quantitative Analysis of Pharmaceutical Formulations.
India: CBS Publications; 2001.
26. ICH Guidelines. Validation of analytical procedures. Text Methodol 2015;
2:8-13.
27. Kiran KK, Nadh RV, Nagoji KEV. Extractive spectrophotometric
determination of nicergoline through ion-pair complexation reaction.
Orient J Chem 2013;29:263-9.
28. Sudhir MS, Nadh RV. Simple and validated ultraviolet
spectrophotometric method for the estimation of febuxostat in bulk and
pharmaceutical dosage forms. Orient J Chem 2013;29:1507-14.
29. Kiran KK, Nadh RV, Nagoji KE. Determination of bendamustine
hydrochloride in pure and dosage forms by ion-associative complex
formation reaction. Orient J Chem 2014;30:905-10.
30. Gorumutchu GP, Ratnakaram GV. Oxidative coupling: A tranquil
approach for determination of selexipag by visible spectrophotometry.
Orient J Chem 2018;34.
31. Gorumutchu GP, Ratnakaram VN. Determination of mianserine using
tropaeoline-OOO by ion pair formation. Int J Appl Pharm 2019;1:11.
32. Gorumutchu GP, Ratnakaram VN. Determination of mianserine using
Fe3+-phenanthroline by visible spectrophotometry. Res J Pharm Techn
2019;1:12.
33. Manasi BK, Anagha MJ. An experimental design approach for
optimization of modified colorimetric first-order derivative method for
estimation of serralysin in bulk and pharmaceutical formulation. Asian
J Pharm Clin Res 2018;11:293-300.
34. Akram M, Monuir ZE, Nora O, Saleem S. Extractive-spectrophotometric
determination of some antimuscarinic antagonist in tablet formulations
using eriochrome cyanine R. Int J Pharm Pharm Sci 2018;4:22-8.
35. Sharma DK, Singh J, Raj P. Spectrophotometric determination of
propranolol hydrochloride and metoprolol tartrate in pharmaceutical
dosage forms, spiked water and biological fluids. Int J Pharm Pharm
Sci 2018;10:107-15.
36. Godambe RD, Disouza JI, Jamkhandi CM, Kumbhar PS. Development
of spectrophotometric and fluorometric methods for estimation of
darunavir using Qbd approach. Int J Curr Pharm Res 2018;10:13-9.
163