Icom IC-7700 HF/50MHz Transceivers
Maklumat Produk
Spesifikasi:
- model: i7700
- Versi Firmware: 2.00
- Fungsi Tambahan: IF filter passband width setting, spectrum scope screen enhancements, audio scope function, QSO voice recording function, voice recorder function changes, repeat transmit function, audio adjustment for CW operation, transmission timing adjustment, server function for remote control, CI-V commands
Arahan Penggunaan Produk
- Kemas kini Firmware:
- Before updating, refer to Section 16 ‘UPDATING THE FIRMWARE’ in the IC-7700 instruction manual for detailed instructions.
- Make a backup file of the transceiver’s settings to a USB flash drive before updating firmware to prevent data loss.
- The CPU will reset automatically during the update process, clearing memory contents and returning all settings to default.
- IF Filter Passband Width Setting:
- Mode: SSB, SSB-D, CW, PSK, RTTY, AM, AM-D, FM, FM-D
- Adjustable Range: Varies based on mode (refer to manual)
- To adjust: Hold down FILTER for 1 second, push FILTER to select desired IF filter, push [BW] F-1 and rotate main dial to set passband width, repeat if needed, push EXIT/SET to exit.
- Spectrum Scope Screen Enhancements:
- New features include waveform outline, waterfall display, wide screen size displays, and USB mouse operation.
- Audio Scope Function:
- New feature added for audio analysis.
- QSO Voice Recording Function:
- New feature added for voice recording during QSOs.
- Repeat Transmit Function:
- New feature added to enable repeat transmission in voice transmission.
- Audio Adjustment for CW Operation:
- New feature added for audio peak filter adjustment during CW operation.
- Transmission Timing Adjustment:
- New feature added to adjust transmission timing for HF and 50 MHz bands to prevent damage to external devices.
- ServeFunction for Remote Control:
- New feature added for remote control stations with optional RS-BA1.
- CI-V Commands:
- Additional commands added for enhanced functionality (refer to manual).
Soalan Lazim
- Q: What should I do before updating the firmware?
- A: Make sure to create a backup file of the transceiver’s settings on a USB flash drive to avoid data loss during the update process.
- Q: Will the firmware update reset all settings to default?
- A: Yes, the CPU will be automatically reset during the firmware update, clearing memory contents and returning all settings to default.
“`
i7700
Firmware update information– Ver. 2.00
Thank you for using the Icom Download Service. Version 2.00 of the firmware will provide the following additional functions or changes to your IC-7700.
A new feauture, another procedure is added to the IF filter passband width setting. (p. 2) New features, the waveform outline, water fall, wide screen size displays and USB mouse operation are
added to the spectrum scope screen. (pp. 3 to 7) A new feature, the audio scope function is added. (pp. 8, 9) A new feature, the QSO voice recording function is added and the Voice recorder function is changed.
(pp. 10 to 23) A new feature, the repeat transmit function is added to the Voice transmission. (p. 19) A new feature, the audio adjustment for audio peak filter for CW operation, is added. (p. 24) A new feature, adjustment of the transmission’s timing for HF and 50 MHz bands is added to prevent
damage to the external devices. (p. 25, Other set mode: TX delay (HF), TX Deley (50M)) A new feature, the Server function for remote control stations with the optional RS-BA1, is added.
(pp. 25 to 28, Other set mode) Some CI-V commands are added, as described on pages 29 and 30.
Before updating, see Section 16 `UPDATING THE FIRMWARE’ in the IC-7700 instruction manual, for details.
IMPORTANT! Make a backup file of the transceiver’s settings, such as stored memory channels, filter settings, to the USB flash drive before updating the firmware. The CPU will be automatically reset when the firmware update is performed; the transceiver’s memory contents will be cleared and ALL settings will be returned to their default settings. See Section 12 “ File saving’ in the IC-7700 instruction manual, for details.
About the [USB] connector: ·SupportedonlyUSBflashdrive,keyboard,mouseorhub. ·K EEP the transceiver power OFF when connecting or disconnecting a USB keyboard, mouse or hub. ·DO NOT connect the following devices:
– Two or more the same kind of USB devices. (Example: Two USB hubs or two USB mouses)
– Multimedia adapter – USB HDD – Larger than 32 GB USB flash drives – Bluetooth® keyboard or mouse.
Filter passband width setting (except FM mode)
·Duringthepassbandwidthsetting Blinks
Mod
SSB
SSB-D CW PSK
RTTY
AM AM-D
FM FM-D V2.00
IF filter FIL1 (3.0 kHz) FIL2 (2.4 kHz) FIL3 (1.8 kHz) FIL1 (1.2 kHz) FIL2 (500 Hz) FIL3 (250 Hz) FIL1 (2.4 kHz) FIL2 (500 Hz) FIL3 (250 Hz) FIL1 (9.0 kHz) FIL2 (6.0 kHz) FIL3 (3.0 kHz) FIL1 (15 kHz) FIL2 (10 kHz) FIL3 (7.0 kHz)
Adjustable range (steps) 50 to 500 Hz (50 Hz) 600 Hz to 3.6 kHz (100 Hz)
50 to 500 Hz (50 Hz) 600 Hz to 3.6 kHz (100 Hz)
50 to 500 Hz (50 Hz) 600 Hz to 2.7 kHz (100 Hz)
200 Hz to 10 kHz (200 Hz)
tetap
q Hold down FILTER for 1 second to enter filter set screen.
w Select any mode except FM. ·P assbandwidthsforFMmodesarefixedandcannotbe
adjusted. e Push FILTER several times to select the desired
IF filter. r Push [BW] F-1 , then rotate the main dial to set the
desired passband width. Then push [BW] F-1 again. ·H olddown[DEF] F-4 for 1 second to select the default
value. ·Whileholdingdown[BW] F-1 , rotating the main dial
also adjusts the desired passband width. t If desired, repeat steps w to r. y Push EXIT/SET to exit filter set screen.
The PBT shift frequencies are cleared when the passband width is changed.
This filter set screen graphically displays the PBT shift frequencies and CW pitch operations.
2
A-6937-2EX
Skrin skop spektrum
D Center mode
MARKER HOLD CENT/FIX
F-3
F-4
F-5
SPAN ATT
F-1
F-2
EXIT/SET
WIDE F-7
·Spectrumscope
Waterfall ·Scopespurioussignalexample Spurious signals may be received on the spectrum scope screen regardless of the transceiver’s state (TX or RX). They are generated in the scope circuit. This does not indicate a transceiver malfunction.
Scope spurious example
This DSP-based spectrum scope allows you to display the frequency and relative signal strength of received signals on the strengths of signals. The IC-7700 has two modes for the spectrum display– one is center mode, and the other is fixed mode.
In addition, the IC-7700 has a mini scope screen to save screen space.
Displays signals around the set frequency within the selected span. The set frequency is always displayed at the center of the screen.
q Push EXIT/SET several times to close any multi-
function screens, if necessary.
w Push [SCOPE] F-1 to select the scope screen.
·Push[WIDE] F-7 to toggle the screen size between
normal and wide.
e Push [CENT/FIX] F-5 to select the center mode.
· "
” is displayed when center mode is selected.
r Push [SPAN] F-1 several times to select the scope
span.
·±2.5,±5.0,±10,±25,±50,±100and±250kHzarese-
lectable.
·Holddown[SPAN] F-1 for1secondtoreturnto±2.5
kHz span.
·Sweepspeedisselectableforeachspanindependently
in scope set mode.
t Push [ATT] F-2 several times to activate an at-
tenuator or turn the attenuator OFF.
·10,20and30dBofattenuationisavailable.
·Holddown[ATT] F-2 for 1 second to turn OFF the at-
tenuator.
y Push [MARKER] F-3 to turn the marker for trans-
mit frequency ON or OFF.
·” ” displays the marker at the transmit frequency.
·”<<“or”>>”appearswhenthemarkerisoutofrange.
·Thespectrumscopeshowsthetransmitsignalwhile
transmitting. This can be deactivated in scope set
mod.
·Thespectrumscopeshowsthepeaklevelholdfunc-
tion. Peak levels are displayed in the background of the
current spectrum in a different color until the receive fre-
quency changes. This can be deactivated and the wave-
form color can be set in scope set mode.
u Push [HOLD] F-4 to freeze the current spectrum
paparan.
·” HOLD ” appears while the function is in use.
·Thepeakholdfunctioncanbedeactivatedinscopeset
mod.
i Push EXIT/SET to exit the scope screen.
NOTE: If a strong signal is received, a ghost signal may also appear. Push [ATT] F-2 several times to activate the spectrum scope attenuator in this case. Spurious signals may be displayed. They are generated in the internal scope circuit and do not indicate a transceiver malfunction.
V2.00
3
A-6937-2EX
Spectrum scope screen (continued)
D Fixed mode
MARKER HOLD CENT/FIX
F-3
F-4
F-5
ATT
EXIT/SET
F-2
Displays signals within the specified frequency range. Conditions on the selected frequency band can be observed at a glance when using this mode.
q Push EXIT/SET several times to close any multi-
function screens, if necessary.
w Push [SCOPE] F-1 to select the scope screen.
·Push[WIDE] F-7 to toggle the screen size between
normal and wide.
e Push [CENT/FIX] F-5 to select the fixed mode.
· "
” is displayed when fixed mode is selected.
r Push [ATT] F-2 several times to activate an at-
tenuator or turn the attenuator OFF.
·10,20and30dBofattenuationisselectable.
·Holddown[ATT] F-2 for 1 second to turn OFF the at-
tenuator.
t Push [MARKER] F-3 several times to select the
marker for transmit frequency or turn the marker
DIMATIKAN.
·” R ” displays the marker at the receive frequency. (al-
ways displayed)
·” ” displays the marker at the transmit frequency.
·”<<“or”>>”appearswhenthemarkerisoutofrange.
·Thespectrumscopeshowsthetransmitsignalwhile
transmitting. This can be deactivated in scope set
mod.
·Thespectrumscopeshowsthepeaklevelholdfunc-
tion. Peak levels are displayed in the background of the
current spectrum in a different color until the receive fre-
quency changes. This can be deactivated and the wave-
form color can be set in scope set mode.
y Push [HOLD] F-4 to freeze the current spectrum
bentuk gelombang.
·” HOLD ” appears while the function is in use.
·Thepeakholdfunctioncanbedeactivatedinscopeset
mod.
u Push EXIT/SET to exit the scope screen.
NOTE: If a strong signal is received, a ghost signal may appear. Push [ATT] F-2 several times to activate the spectrum scope attenuator in this case.
The scope bandwidth can be specified for each frequency band independently in scope set mode.
V2.00
4
A-6937-2EX
Spectrum scope screen (continued)
D Mini scope screen display
M.SCOPE
The mini scope screen can be displayed with another screen display, such as set mode menu, decode screen, memory list screen, etc. simultaneously.
q Set the scope mode (center or fixed), marker, attenuator, span, etc. in advance. (pp. 3, 4)
w Push M.SCOPE to toggle the mini scope display ON or OFF.
·TheS/RFmetertypeduringminiscopedisplaycan be selected in display set mode (Meter Type (Wide Screen) item). (IC-7700 instruction manual Section 12)
D Scope set mode
LEBAR
F-3
F-7
DEF EXIT/SET Main dial
F-1
F-2
F-4
This set mode is used to set the waveform color, sweeping speed, scope range for fixed mode, etc.
q During spectrum scope display ON, push [SET] F-6 to select scope set mode screen.
·Push[WIDE] F-7 to toggle the screen size between normal and wide.
w Push [Y] F-1 or [Z] F-2 to select the desired set item.
e Set the desired condition using the main dial. ·Holddown[DEF] F-4 for 1 second to select the de-
fault condition or value. ·Push[t u] F-3 to select the set contents for some
items. r Push EXIT/SET to exit from set mode.
V2.00
5
A-6937-2EX
Spectrum scope screen D Scope set mode (continued)
Waveform Type Select the outline indication of the waveform for the spectrum scope.
Waveform Color (Line) Set the waveform color for the currently received signals.
Waterfall Display Set the waterfall display to ON or OFF.
Waterfall Peak Color Level The signal level that reaches a peak color is set to Grid 1 to Grid 8 for the waterfall display. Higher signal levels are Red, Yellow, Green, Lightblue, Blue and Black in order.
isi
·Fill
: The waveform is described by only the
warna.
·Fill+Line:Thewaveformisdescribedbythecolor
and outline.
70
30
0
·ThecolorissetinRGBformat. ·Push[ ] F-3 to select R (Red), G (Green) and
B (Blue), and rotate the ratio from 0 to 255 range. ·ThesetcolorisindicatedintheboxbesidetheRGB
skala.
ON
·ON : Displays the waterfall of the spectrum scope. ·OFF:Doesnotdisplaythewaterfall.
Grid 8
V2.00
6
A-6937-2EX
Spectrum scope screen (continued)
D USB mouse operation
Penunjuk tetikus
If you connect a USB mouse to the transceiver, a mouse pointer appears on the spectrum scope screen. Now, you can change the frequency by using the mouse.
While holding down [XFC], the mouse changes the transmit frequency.
·MouseoperationontheCentermode
Button Left Right
Operation Click Drag
Click/Drag
Penerangan
The frequency changes to the clicking point and mouse pointer move to the center of the screen.
The frequency changes to the clicking point and mouse pointer move to the center of the screen, and then the frequency increases or decreases.
The Right button temporarily changes the frequency. While holding the button, same action as the Left button, but release it to return to the original frequency.
·MouseoperationontheFixmode
Butang Kiri
Betul
Operation Click Drag
Click/Drag
Penerangan
The frequency and marker change to the clicking point.
The frequency and marker change to the clicking point, and then the frequency increases or decreases.
The Right button temporarily changes the frequency. While holding the button, same action as the Left button, but release it to return to the original frequency.
Changing frequencies in the Drag operation differ depending on the tuning step settings.
V2.00
7
A-6937-2EX
Skrin skop audio
MASA TAHAP
SET
F-5
F-6
F-7
ATT HOLD EXIT/SET
F-2
F-4
·Audioscope
This audio scope allows you to display the received signal’s frequency component to the FFT scope, and its waveform component to the Oscilloscope. The FFT scope has an waterfall.
q Push EXIT/SET several times to close any multifunction screens, if necessary.
w Push [AUDIO] F-6 to select the scope screen. e Push [ATT] F-2 several times to activate an at-
tenuator or turn OFF the attenuator for the FFT scope. ·0(OFF),10,20and30dBattenuatorsareselectable. ·Holdingdown[ATT] F-2 for 1 second to turn the at-
tenuator OFF. t Push [LEVEL] F-5 to select the level setting for
the Oscilloscope. ·0,10,20and30dBareselectable. y Push [TIME] F-6 several times to select the time
setting for the Oscilloscope. ·1,3,10,30,100and300ms/Divareselectable. u Push [HOLD] F-4 to freeze the current audio
waveform. ·” HOLD ” appears while the function is in use. i Push EXIT/SET to exit the scope screen.
When the Monitor function is ON, you can see the TX audio on the Audio scope. ·Rotate [MONI GAIN] to adjust the level setting for the
TX audio.
Waterfall FFT Scope
Osiloskop
V2.00
8
A-6937-2EX
Audio scope screen (continued)
D Audio scope set mode
F-1 F-2 F-3
DEF EXIT/SET F-4
This set mode is used to set the FFT scope waveform type, color, waterfall display and oscilloscope waveform color.
q During audio scope display ON, push [SET] F-7 to select the Audio scope set mode screen.
w Push [Y] F-1 or [Z] F-2 to select the desired set item.
e Set the desired condition using the main dial.
·Holddown[DEF] F-4 for 1 second to select the default condition or value.
·Push[t u] F-3 to select the set contents for some items.
r Push EXIT/SET to exit from set mode.
FFT Scope Waveform Type Select the waveform type for the FFT scope.
FFT Scope Waveform Color Set the waveform color for the FFT scope.
FFT Scope Waveform Display Select the waterfall display ON or OFF.
Oscilloscope Waveform Color Set the waveform color for the Oscilloscope.
isi
·Fill : The waveform is represented by the color. ·Line:Thewaveformisrepresentedbyoutline.
51
153
255
·ThecolorissetinRGBformat. ·Push[ ] F-3 to select R (Red), G (Green) and
B (Blue), and rotate the ratio from 0 to 255 range. ·ThesetcolorisindicatedintheboxbesidetheRGB
skala.
ON
·ON : Displays the waterfall on the FFT scope. ·OFF:Doesnotdisplaythewaterfall.
0
255
0
·ThecolorissetinRGBformat. ·Push[ ] F-3 to select R (Red), G (Green) and
B (Blue), and rotate the ratio from 0 to 255 range. ·ThesetcolorisindicatedintheboxbesidetheRGB
skala.
V2.00
9
A-6937-2EX
`Section 7 VOICE RECORDER FUNCTIONS’ in the IC-7700 instruction manual has been changed, and a lot of operations are different. So all instructions in Section 7 are described on pages 10 to 23.
Merakam audio QSO
NOTE: ·Be sure to connect a USB flash drive before re-
cording a QSO audio. ·Once recording starts, it continues, even if the
transceiver is turned OFF and then ON again.
The Voice recorder function records a QSO (communication) audio onto a USB flash drive. This function enables you to record both received and transmitted audio, a QSO with a DX’pedition, and playback the recorded audio after the QSO.
D To start or stop recording
QSO REC F-2
EXIT/SET
q Push EXIT/SET several times to close a multi-func-
tion screen, if necessary. w Push [VOICE] F-2 to display the Voice Recorder
menu. e Hold down [QSO REC] F-4 for 1 second to start
rakaman suara.
·T he ” ” indicator appears and the ” USB ” indicator
sekelip mata.
·Recordingiscontinuousuntilyoumanuallystoprecord-
ing, or the USB flash drive becomes full.
·If the recording file’s content reaches 2GB, the trans-
ceiver automatically creates a new file, and continues
rakaman.
·The” “indicatorappearsinsteadofthe” ” indicator
while recording is paused. r Hold down [QSO REC] F-4 for 1 second to stop
rakaman.
·T he” “indicatordisappearsandthe” USB ” indicator
stops blinking. t Push EXIT/SET to exit the Voice Recorder screen.
Convenient! When the PTT Automatic Recording function is set to ON in the Voice set mode, the recording automatically starts when you push [PTT]. (p. 22)
Recording quick operation
D To start or stop recording
q Hold down REC for 1 second to start voice record-
ing. ·T he ” ” indicator appears and the ” USB ” indicator
blinks. w Hold down REC for 1 second again to stop record-
ing.
V2.00
REKAM 10
A-6937-2EX
Playing back the recorded audio (QSO)
D Basic playing
BERMAIN
F-1
F-2
F-3
Berkedip
Progress bar Shows the play back progress bar.
Total time Shows the file’s total playback time.
Played back time Shows the played back time.
Playback mark Appears while the audio is playing back. ·T hemarkdisappearswhilepausing.
q Push EXIT/SET several times to close a multi-function screen, if necessary.
w Push [VOICE] F-2 to display the Voice Recorder menu.
e Push [QSO PLAY] F-5 to call up the voice QSO player screen.
·Thefolderlistisdisplayed. ·Thefoldernameisformattedyyyymmdd(yyyy:year,
mm: month, dd: day). r Push [p] F-1 or [q] F-2 to select the folder that
contains the file you want to play. ·Rotatingthemaindialalsoselectsthefolder. t Push [FILE] F-3 to open the folder . ·Thefilelistisdisplayed. ·Thefilenameisformattedyyyy-mm-ddhh:mm:ss(yyyy:
year, mm: month, dd: day, hh: hour, mm: minute, ss: second). y Push [p] F-1 or [q] F-2 to select the file that you want to play. ·Rotatingthemaindialalsoselectsthefile. u Push [PLAY] F-3 to start playback.
·Tthe” USB ” indicator blinks. ·Playback continues to next file, and it is terminated
when the bottom file in the folder is played. i Push EXIT/SET several times to exit the QSO player
skrin.
V2.00
11
A-6937-2EX
Playing back the recorded audio (continued)
D Operating while playing back
BERHENTI
F-1 F-2 F-3 F-4 F-5 F-6
Putar balik
ke hadapan
Main sebelumnya file
Main seterusnya file
Jeda atau main
Berhenti bermain
Convenient! You can fast forward or rewind the file that is playing by rotating the main dial. The fast forward/rewind time is one twentieth of the total file time, regardless of the skip time setting.
Holding down the switch repeats the action until it is released (other than the [ ] F-3 switch). Example: Hold down [] F-4 to repeat skipping 10 seconds until you release the [] F-4 switch.
(Lalai: 10 saat)
You can fast forward or rewind while playing back.
·Fastforwardwhileplaying Push [] F-4 to fast forward to the skip time point. (Default: 10 seconds) You can change the skip time in the voice set mode. (p. 22)
·Rewindwhileplaying Push [] F-2 to rewind to the skip time point. (Default: 10 seconds) You can change the skip time in the voice set mode. (p. 22) ·If you push [] F-2 within the first second of the file, the skip time at the end of the previously recorded file will playback.
·Pausewhileplaying Push [ ] F-3 to pause. ·Touch[ ] F-3 again to resume.
·Playingthepreviousfile
Push [] F-1 to play the previous file.
·Incasethereareotherfilesinthefolder,whiletheoldest file is playing back, Push [] F-1 to start playing the beginning of the file.
·Playingthenextfile Push [] F-5 to play the next file. ·Incasethereareotherfilesinthefolder,whilethemost recent file is playing back, Push [] F-5 to stop the playback.
·Movingtothebeginningofthepreviousfile When the playback is paused anywhere within the file, Push [] F-2 one or more times to return to the beginning of the file, and pause. ·P ush[ ] F-3 to play it back.
When the playback is paused at beginning of a file, Push [] F-1 to move to the beginning of the previous file, and pause. ·P ush[ ] F-3 to play it back.
·Movingtothebeginningofthenextfile When the playback is paused, Push [] F-5 to move to the beginning of the next file, and pause. ·P ush[ ] F-3 to play it back.
V2.00
12
A-6937-2EX
Deleting recorded audio file
[F-1·Y] [F-2·Z] [F-5·DEL]
q Push EXIT/SET several times to close a multi-function screen, if necessary.
w Push [VOICE] F-2 to display the Voice Recorder menu.
e Push [QSO PLAY] F-5 to call up the voice QSO player screen.
·Thefolderlistisdisplayed. ·T hefoldernameisformattedyyyymmdd(yyyy:year,
mm: month, dd: day). r Push [Y] F-1 or [Z] F-2 to select the folder that
contains the file you want to delete. ·Rotatingthemaindialalsoselectsthefolder. t Push [FILE] F-3 to open the folder . ·Thefilelistisdisplayed. ·Thefilenameisformattedyyyy-mm-ddhh:mm:ss(yyyy:
year, mm: month, dd: day, hh: hour, mm: minute, ss: second). y Push [Y] F-1 or [Z] F-2 to select the file that you want to delete. ·Rotatingthemaindialalsoselectsthefile. u Hold down [DEL] F-5 for 1 second to delete the file. ·Theconfirmationwindow”Areyousure?”appears. i Push [OK] F-6 to delete the file. ·Theselectedfileisdeleted. ·Push EXIT/SET to cancel deleting. o Push EXIT/SET several times to exit the QSO player screen.
Deleting recorded audio folder
[F-1·Y] [F-2·Z] [F-5·DEL]q Push EXIT/SET several times to close a multi-func-
tion screen, if necessary.
w Push [VOICE] F-2 to display the Voice Recorder
menu.
e Push [QSO PLAY] F-5 to call up the voice QSO
player screen.
·Thefolderlistisdisplayed.
·T hefoldernameisformattedyyyymmdd(yyyy:year,
mm: month, dd: day).
r Push [Y] F-1 or [Z] F-2 to select the folder that
anda mahu padam.
·Rotatingthemaindialalsoselectsthefolder.
t Hold down [DEL] F-5 for 1 second to delete the
folder.
·Theconfirmationwindow”Areyousure?”appears.
y Push [OK] F-6 to delete the folder.
·Theselectedfolderisdeleted.
·Push EXIT/SET to cancel deleting.
u Push EXIT/SET several times to exit the QSO player
skrin.
V2.00
13
A-6937-2EX
About digital Voice Recorder
F-1
F-2
REC PLAY EXIT/SET
The IC-7700 has digital voice memories, up to 4 messages for transmit, and up to 20 messages for receive. A maximum message length of 30 seconds can be recorded into a receive memory (total message length for all channels of up to 209 seconds) and a total message length of up to 99 seconds can be recorded in transmit memory.
The transmit memory is very convenient for repeated CQ and exchange transmissions in contests, as well as when making repeated calls during DX’peditions.
q Select any mode. w Push [VOICE] F-2 to display voice recorder menu. e Push [PLAY] F-1 or [MIC REC] F-2 to select the
desired memory channel screen, then record audio or playback the contents as described below. r Push EXIT/SET twice to exit voice recorder screen.
·Aboutrecordingreceivedaudioandplayingbackthecontents
· Cthample– When [REC] is pushed momentarily Push REC momentarily Push REC momentarily
NOTE: The contents will be recorded into an independent memory channels automatically.
15 sec. 3 sec. (default)
Push REC momentarily records the contents of the previous 15 sec.*
When REC is pushed momentarily again within 15 sec.* from the last REC operation, all the contents between REC operations will be recorded.
*The recording time period can be changed with “Normal Rec Time” in voice set mode (p. 21).
· Playing back the all contents in a channel
BERMAIN
Tolak
sekejap.
F-3
Or, hold down PLAY for 1 sec.
· Playing back the end of 5 sec.* in a channel Push PLAY momentarily.
30 sec. (max.)
Not playing back
Play back (5 sec.; default)
*The playing back time period can be changed with “Short Play Time” in voice set mode (p. 21).
V2.00
14
A-6937-2EX
Recordingareceivedaudio(ShortREC)
Up to 20 channels of receive voice memories are available in the IC-7700. And the total audio length of up to 209 seconds can be recorded in receive channels. However, the maximum recordable length into a single memory is 30 seconds.
This Voice Recorder does not record only the received audio, but also the information such as set operating frequency, mode, and the recording time for your future reference.
D One-touch recording
Push REC momentarily to records the previous 15 seconds audio.
·Therecordabletimeperiodcanbesetinvoicesetmode. (p. 21)
·T heoperatingfrequency,modeandcurrenttimeareautomatically programmed as the memory names.
NOTE: When transmit (or [PTT] is pushed) within the set period, no audio will be recorded.
REC
IMPORTANT! When you record the 21st audio segment, or when the total audio length exceeds 209 seconds, the oldest recorded audio is automatically erased to make room for the new audio.
Playing back the recorded audio (Short REC)
D Basic playing
BERMAIN
F-1
F-2
F-3
Muncul
q Push EXIT/SET several times to close a multi-
function screen, if necessary. w Push [VOICE] F-2 to display the Voice recorder
menu. e Push [PLAY] F-1 to display the Voice recorder
skrin.
· Previously selected screen,TX or RX memor y, is dis-
played. If theTX memor y message (T1T4) appears,
push [T/R] F-7 to select RX memory message.
r Push [Y] F-1 or [Z] F-2 to select the desired voice memory to playback.
t Push [PLAY] F-3 to start playback.
· "
” indicators appear and the timer counts down.
y Push [PLAY] F-3 again to stop playback if de-
tuan.
·Playbackisterminatedautomaticallywhenallofthere-
corded contents in the message are played. u Push EXIT/SET twice to exit the voice recorder
skrin.
Appears V2.00
Counts down 15
A-6937-2EX
Playing back the recorded audio (Short REC) (continued)
D One-touch playing
BERMAIN
The previously recorded audio in message 1 can be played back without selecting voice recorder screen.
Push PLAY momentarily to play back the last 5
seconds of the previously recorded audio.
· "
” penunjuk muncul.
·Playbackisterminatedautomaticallyafter5seconds.
·Theplaybacktimeperiodcanbesetinvoicesetmode.
(ms 21)
Hold down PLAY for 1 second to playback all of the previously recorded audio.
· "
” penunjuk muncul.
·Playbackisterminatedautomaticallywhenallofthere-
corded contents in the channel are played.
Protect the recorded contents
The protect function is available to protect the recorded contents from accidental erasure, such as over-writing, etc.
MELINDUNGI
F-1
F-2
F-4
q Push EXIT/SET several times to close a multifunction screen, if necessary.
w Push [VOICE] F-2 to display the Voice recorder menu.
e Push [PLAY] F-1 to display the Voice recorder screen.
·P reviouslyselectedscreen,TXorRXmemory,isdis-
played. If theTX memor y message (T1T4) appears,
push [T/R] F-7 to select RX memory message. r Push [Y] F-1 or [Z] F-2 to select the desired
voice message. t Push [PROTECT] F-4 to turn the protect function
ON or OFF. ·” ” indicator appears when the contents is protected.
y Push EXIT/SET twice to exit the voice recorder menu.
Erasing the recorded contents
CLR
F-1
F-2
F-5
The recorded contents can be erased independently by message.
q Perform the steps q to eas” Protect the recorded contents” above.
w Push [Y] F-1 or [Z] F-2 to select the desired voice message to be erased.
e Hold down [CLR] F-5 for 1 second to erase the contents.
·P ush[PROTECT] F-4 to release the protection in advance if necessary.
r Push EXIT/SET twice to exit the voice recorder menu.
V2.00
16
A-6937-2EX
Recording a message for transmit
To transmit a message using the Voice recorder, record the desired message in advance as described below. The IC-7700 has digital voice memories for transmission, up to 4 messages and you can record message in length of up to 99 seconds.
D Rakaman
F-1
F-2
REC F-4
Muncul
Adjust [MIC] control so that this indicator reads within 100%.
q Push EXIT/SET several times to close a multi-func-
tion screen, if necessary.
w Push [VOICE] F-2 to display the Voice recorder
menu.
e Push [MIC REC] F-2 to select the voice mic. re-
cord screen.
r Push [Y] F-1 or [Z] F-2 to select the desired
mesej.
t Hold down [REC] F-4 for 1 second to start record-
ing.
· "
” penunjuk muncul.
·Speakintothemicrophonewithoutholdingdown[PTT].
·Previouslyrecordedcontentsarecleared.
·Audiooutputfromtheinternalspeakerisautomatically
disenyapkan.
y While speaking into the microphone with your nor-
mal voice level, adjust the [MIC] control so that the
[MIC-REC LEVEL] indicator reads within 100%.u Push [REC] F-4 momentarily to stop recording.
·Therecordingisterminatedautomaticallywhenthere-
maining time becomes 0 second.
i Push EXIT/SET twice to exit the Voice recorder
menu.
D Confirming a message for transmit
BERMAIN
F-1
F-2
F-3
q Perform the steps q to eas”D Recording” above.
w Push [Y] F-1 or [Z] F-2 to select the desired message.
e Push [PLAY] F-3 to playback the recorded con-
khemah.
· "
” penunjuk muncul.
r Push [PLAY] F-3 again to stop playback.
·Playbackisterminatedautomaticallywhenallofthere-
corded contents in the message are played.
t Push EXIT/SET twice to exit the voice recorder screen.
V2.00
17
A-6937-2EX
Programming a memory name
DEL
123 / Symbol ABC / abc
F-3
Papan kekunci
SPACE T1..T4
F-1
F-2
F-4
F-7
·Voicememorynameeditingexample
Memory messages can be tagged with alphanumeric names of up to 20 characters each.
C(!a#p$ita%l le&tt¥er?s,”s`m`^al+l letter/s.,,n:u;m=e<ra>ls(,)so[m]{e}s|y_m~b@ols) and spaces can be used. (See the table below.)
q Record a message as described in page 17. w During the voice mic. record screen display, push
[NAME] F-5 to enter memory name edit condition. ·Acursorappearsandblinks. e Push [T1..T4] F-7 several times to select the de-
sired voice message. r Input the desired character by rotating the main dial
or by pushing the band key for number input. ·Push[ABC](MF6) or [abc] (MF6) to toggle capital and
small letters. ·P ush[123](MF7) or [Symbol] (MF7) to toggle numerals
and symbols. ·Push[t] F-1 or [u] F-2 for cursor movement.
·Push[DEL] F-3 to delete the selected character.
·Push[SPACE] F-4 to input a space.
·Pushingthetransceiver’skeypad,[0][9],canalso enter numerals.
t Push EXIT/SET to input and set the name. ·Thecursordisappears. y Repeat steps e to t to program another voice
message’s name, if desired. u Push EXIT/SET twice to exit the voice recorder
skrin.
·Usablecharacters Key selection
Editable characters A to Z (capital letters)
a to z (small letters)
0 to 9 (numbers)
!#$%&¥?”“^+ / . , : ; =<>()[]{}|_~@
For your convenience When a PC keyboard is connected to [USB] connector on the front panel, the memory name can also be edited from the keyboard.
V2.00
18
A-6937-2EX
Sending a recorded message
D Single TX
T1 T2 T3 T4 EXIT/SET
T/R
F-1 F-2 F-3 F-4
F-7
Muncul
Counts down
q Push EXIT/SET several times to close a multi-function screen, if necessary.
w Select a phone mode by pushing SSB or AM/FM .
e Push [VOICE] F-2 to enter the Voice recorder
menu. r Push [PLAY] F-1 to enter the Voice recorder
screen. ·Ifthereceivevoicemessageappears,push[T/R] F-7
toselectTXmessage(T1T4). t Push a desired message switch, [T1] F-1 to
·Thetransceivertransmitsautomatically.
· "
” indicator appears and the memory timer
mengira mundur.
·Y ouhearthetransmittedmessagefromthespeakeras
the default. This can be turned OFF in voice set mode.
(ms 21)
y Push the selected message switch, [T1] F-1 to
[T4] F-4 , again to stop, if desired.·Thetransceiverreturnstoreceiveautomaticallywhenall
of the recorded contents in the message are transmit-
ted.
u Push EXIT/SET twice to exit the voice memory
skrin.
D Repeat TX
T1 T2 T3 T4 EXIT/SET
T/R
F-1 F-2 F-3 F-4
F-7
Muncul
Penunjuk ulang
q Perform steps q to r above. w Hold down a desired message switch, [T1] F-1 to
[T4] F-4 , for 1 second to repeatedly transmit the recorded voice audio for up to 10 minutes at the intervalspecifiedin”RepeatTime.” ·Evenif10minutespasswhiletransmitting,thevoice
audio is completely transmitted. ·Oneofthefollowingstepswillcancelthetransmission.
– Push the memory again. – Push another memory (except for [TX LEV.]). – Exit the TX Voice memory screen. – Turn OFF the power, then turn it ON again. – Activate the transmission.
The repeat transmission is cancelled. But while transmitting, the voice audio is completely transmitted. ·OncetheRepeatTXismade,thetransceiverpauses untiltheendofthe”RepeatTime,”thentransmitsagain. After the second transmission, the Repeat TX continues pausing, if receiving a signal. But if the squelch is manually opened, the voice audio is repeatedly transmitted, according to the repeat time setting.
For your convenience When an external keypad or PC keyboard is connected, the recorded message, T1 to T4, can be transmitted without opening the Voice Recorder screen. See the IC-7700 instruction manual’s Section 2 and Section 12 for details.
·T herecordedmessage,T1toT4istransmittedoncewhenpushingoneoffourswitchesontheexternalkeypad;therecorded message is repeatedly transmitted when holding down a switch.
·The recorded message, T1 to T4 is transmitted once when pushing one of [F1] to [F4] key on the PC keyboard; the recorded message is repeatedly transmitted when pushing a key while holding down [SHIFT] key.
V2.00
19
A-6937-2EX
Sending a recorded message (continued)
DTransmitlevelsetting
DEF F-7
TX LEV. F-6
EXIT/SET Main dial
q Call up the Voice recorder screen as described
di atas.
w Push [TX LEV.] F-6 to select the voice memory
transmit level set condition.
e Push the desired message switch, [T1] F-1 to
[T4] F-4 , momentarily to transmit the contents.·Thetransceivertransmitsautomatically.
· "
” indicator appears and the memory timer
mengira mundur.
r Rotate the main dial to adjust the transmit voice
tahap.
·H olddown[DEF] F-7 for 1 second to select the default condition.
t Push EXIT/SET to return to the voice recorder
skrin.
Voice set mode
F-1
F-2
DEF F-4
EXIT/SET
Dail utama
Sets the automatic monitor function, short play and normal recording times for voice recorder.
q Push EXIT/SET several times to close a multi-function screen, if necessary.
w Push [VOICE] F-2 to display the Voice recorder menu.
e Push [SET] F-7 to select voice set mode screen. r Push [Y] F-1 or [Z] F-2 to select the desired
item. t Rotate the main dial to set the desired condition or
value. ·H olddown[DEF] F-4 for 1 second to select the default
condition or value.
y Push EXIT/SET to exit the voice set mode screen.
V2.00
20
A-6937-2EX
Voice set mode (continued)
Voice 1st Menu Select VOICE-Root or VOICE-PLAY as the menu that appears first after pushing [VOICE] F-2 .
Auto Monitor
Turn on the automatic monitor function for recorded audio contents transmission.
Repeat Time Set the repeat interval for the voice repeat transmission to between 1 and 15 seconds (in 1 second steps). The transceiver repeatedly transmits the recorded voice audio at this interval.
Short Play Time Set the desired time period for one-touch playback (when PLAY is pushed momentarily).
Normal Rec Time Set the desired time period for one-touch recording (when REC is pushed momentarily).
QSO REC Mode Select the recording mode for recording a QSO audio.
RX REC Condition Select whether or not the squelch status affects the RX voice audio recording.
VOICE-Root
·VOICE-Root :Thevoicemenuappearsfirst. ·VOICE-PLAY :EithertheRXorTXvoiceRecorder
screen appears first.
ON
·ON :Monitorstransmitaudioautomaticallywhen sending a recorded audio.
·OFF :Monitors transmit audio only when the monitor function is in use.
5s
5s
·3to10secondsin1secondstepscanbeset. (default: 5 seconds)
15an
·5to30secondsin1secondstepscanbeset. (default: 15 seconds)
TX&RX
·TX&RX:Recordsboththetransmittedandreceived audio.
·RXonly:Recordsonlythereceivedaudio.
Squelch Auto
·Always:
The transceiver always records the
RX audio, regardless of the squelch
status.
·SquelchAuto:ThetransceiverrecordstheRXaudio
only when a signal is received (the
squelch is opened).
When the squelch closes while re-
cording, the recording will continue
for 2 seconds, and then pause.
V2.00
21
A-6937-2EX
Voice set mode (continued) File Berpisah
Pusingkan File Pisahkan fungsi HIDUP atau MATI.
PTT Auto REC Turn the PTT Automatic Recording function ON or OFF.
QSO PLAY Skip Time Set the Skip time for forwarding or rewinding while playing back the QSO audio. 3, 5, 10 and 30 seconds are selectable.
ON
·OFF:The audio is continuously recorded into the file, even if you switch between transmit and receive or the squelch status changes between open and closed.
·ON: Whilerecording,andifyouswitchbetween transmit and receive, or the squelch status changes between open and closed, a new file dicipta secara automatik dalam folder yang sama, dan audio disimpan ke dalam folder baharu.
DIMATIKAN
·OFF:Therecordingdoesnotstartevenifasignalis transmitted.
·ON: Therecordingautomaticallystartswhenasignal is transmitted.
The recording will continue when:
·A signal is transmitted again within 10 seconds
after the last transmission.
·A signal is received within 10 seconds after the
last transmission, the received audio is also re-
corded.
– A signal is received within 10 seconds after the
last reception.
·T hesquelchisopenintheFMmodes.
Rakaman akan berhenti apabila:
·Thefrequencyoroperatingmodeischanged.
·Theoperatingmethod(V/M,M-CH,BandStack-
ing Register, and so on) is changed.
·10 minutes has past after the last transmission
while the squelch is open in the SSB, CW, RTTY,
PSK or AM modes.
10an
V2.00
22
A-6937-2EX
SavingavoicemessageintotheUSBflashdrive
DSavingthereceivedaudiomemory The USB flash drive is not supplied by Icom.
The recorded RX memory contents can be saved into the USB flash drive.
SAVE F-6
WIDE F-7
DIR/FILE F-1
EDIT EXIT/SET F-4
Dail utama
·VoicerecorderRXmemoryscreen
·Voicefilesavescreen–filenameedit
·Whilesaving
When a PC keyboard is connected to [USB] connector on the front panel, the file name can also be edited from the keyboard.
q During Voice recorder RX memory screen display, push [SAVE] F-6 to select voice file save screen.
·P reviouslyselectedscreen,TXorRXmemory,isdisplayed. If theTX message (T1T4) appears, push
[T/R] F-7 to select RX message. w Change the following conditions if desired.
·Filename: z Push [EDIT] F-4 to select file name edit condition.
·Push[DIR/FILE] F-1 several times to select the file name, if necessary.
x Push [ABC] (MF6), [123] (MF7) or [Symbol] (MF7) to select the character group, then rotate the main dial to select the character.
·[ABC](MF6) : A to Z (capital letters); [123] (MF7): 0 to 9 (numerals); [Symbol] (MF7):!#$%&“^ (){}_~ @ can be selected.
·Push[t] F-1 to move the cursor left, push [u] F-2 to move the cursor right, push [DEL] F-3 to delete a character and push [SPACE] F-4 to insert a space.
c Push EXIT/SET to set the file nama.
·Savinglocation z Push [DIR/FILE] F-1 to select tree view screen. x Select the desired directory or folder in the USB flash drive.
·Push[t u] F-4 to select the upper directory.
·Push[Y] F-2 or [Z] F-3 to select folder in the same directory.
·Holddown[t u] F-4 for 1 second to select a folder in the directory.
·Push[REN/DEL] F-5 to rename the folder. ·Holddown[REN/DEL] F-5 for 1 second to de-
lete the folder.
·Holddown[MAKE] F-6 for 1 second to making a new folder. (Edit the name with the same mannerasthe”·Filename”above.)
c Push [DIR/FILE] F-1 twice to select the file nama.
e Push [SAVE] F-6 . ·Afterthesavingiscompleted,returntovoicerecorder
RX memory screen automatically.
DSavingtheTXmemory
The TX memory contents can also be saved into the USB flash drive. However, the contents are saved with the message list, set mode conditions, etc. at the same time. See the IC-7700 instruction manual’s Section 12 for details.
V2.00
23
A-6937-2EX
Levelsetmode
You can adjust the audio level for the audio peak filter in the CW mode.
APF AF Level
Sets the audio level that the audio peak filter is ON intheCWmode,from0to+6dBin1dBstep. (default: 0dB)
0dB
ACC set mode
You can adjust the input level for the Ethernet connector [LAN], and also can select it for each operating modes.
LAN MOD Level Sets the desired input level for modulation from [LAN], within 0 to 100% in 1% steps. (default: 50%)
DATA OFF MOD Selects the desired connector(s) for modulation input when data mode is not in use.
DATA1 MOD Selects the desired connector(s) for modulation input when data 1 mode (D1) is in use.
DATA2 MOD Selects the desired connector(s) for modulation input when data 2 mode (D2) is in use.
DATA3 MOD Selects the desired connector(s) for modulation input when data 3 mode (D3) is in use.
50%
MIC,ACC
·MIC
:Usethesignalsfrom[MIC].
·ACC
:Usethesignalsfrom[ACC1](pin4).
·MIC,ACC :U s e t h e s i g n a l s f r o m [ M I C ] a n d
[ACC1] (pin 4). (default)·S/PDIF :Usethesignalsfrom[S/PDIF].
·LAN
:Usethesignalsfrom[LAN].
ACC
·MIC
:Usethesignalsfrom[MIC].
·ACC
:Use the signals from [ACC1] (pin 4).
(lalai)
·MIC,ACC :U s e t h e s i g n a l s f r o m [ M I C ] a n d
[ACC1] (pin 4).·S/PDIF :Usethesignalsfrom[S/PDIF].
·LAN
:Usethesignalsfrom[LAN].
MIC,ACC
·MIC
:Usethesignalsfrom[MIC].
·ACC
:Usethesignalsfrom[ACC1](pin4).
·MIC,ACC :U s e t h e s i g n a l s f r o m [ M I C ] a n d
[ACC1] (pin 4). (default)·S/PDIF :Usethesignalsfrom[S/PDIF].
·LAN
:Usethesignalsfrom[LAN].
MIC
·MIC
:Usethesignalsfrom[MIC].(default)
·ACC
:Usethesignalsfrom[ACC1](pin4).
·MIC,ACC :U s e t h e s i g n a l s f r o m [ M I C ] a n d
[ACC1] (pin 4).·S/PDIF :Usethesignalsfrom[S/PDIF].
·LAN
:Usethesignalsfrom[LAN].
V2.00
24
A-6937-2EX
Other set mode
TX Delay (HF)
Sets the transmission’s timing for the HF bands. When an external device, such as a vacuum tube linear amplifier or a receiver preamplifier, is connected to the transceiver and you use the SEND line, a problem could possibly occur. If the device’s transmit/receive switching time is slower than the time for the Icom transceiver, the device may not yet ready for a transmitted signal, and could be damaged by the transceivers RF power. If necessary to prevent damage to the external device, set an appropriate TX delay.
TX Delay (50M)
Sets the transmission’s timing for the 50 MHz band.
Seeaboveitem”TXDelay(HF)”formoredetails.
Fungsi Tutup
Selects the shutdown option between Standby/Shutdown and Shutdown, for turning ON the transceiver by Remote stations. (default: Shutdown)
Whenthisitemissetto”Standby/Shutdown: z Holding down POWER for 1 second displays the
dialog box below.
OFF ·OFF :The transmission delay is disabled.
(default) ·10to30ms:Aftertransmitoperation,theTXoutput
is delayed for the set period of time (10, 15, 20, 25 or 30 milliseconds).
DIMATIKAN
Shutdown Standby/Shutdown :
You can turn ON the transceiver’s power using external equipment such as a PC with RS-BA1. Shutdown: Only the POWER switch turns ON the transceiver.
x Push POWER to turn OFF the power with the Standby mode.
·Ifyouwanttoselect”Shutdown,”rotatethemaindial or push [q] F-2 , then push POWER .
CIV LANREMOTE Transceive Address
Sets the CI-V address for sending the transceive data from [LAN] to [REMOTE] or [RS-232C]. The [REMOTE] or [RS-232C] connectors output the transceive data with this setting Address.
When your system are configured with any other transceivers or receivers, and you do not want to change their frequency or operating mode by operating the RS-BA1, sets this address different with 00h.
Gerbang Lalai
(Valid after Reboot)
Sets the default gateway of the router that you want to connect the IC-7700 to.
Only when you configure the remote control system using an optional RS-BA1 through the Internet, you need this setting.
NOTE while in the standby mode: ·Theinternalcoolingfanisactive,thisisnormal;
not malfunction.
00j
Only when you configure the remote control system using an optional RS-BA1, you need this setting. The IC-PW1 can receive the transceive data from other than 00h, so you can still operate the IC-PW1 by operating RS-BA1. In that case you must reset the IC-PW1 and set the CI-V settings again. See the ICPW1’s instruction manual for details.
. . . Turn the transceiver power OFF then ON to make the setting effective.
V2.00
25
A-6937-2EX
Others set mode (continued)
Kawalan Rangkaian
(Valid after Reboot)
Selects the remote control capability ON or OFF. (default : OFF)
Only when you configure the remote control system using an optional RS-BA1, you need this setting.
Control Port (UDP) (Valid after Reboot)
Sets the Control port of the IC-7700 by accessing from the remote station.
Only when you configure the remote control system using an optional RS-BA1, you need this setting.
Serial Port (UDP) (Valid after Reboot)
Sets the Serial port of the IC-7700 by accessing from the remote station.
Only when you configure the remote control system using an optional RS-BA1, you need this setting.
Audio Port (UDP) (Valid after Reboot)
Sets the Audio port of the IC-7700 by accessing from the remote station.
Only when you configure the remote control system using an optional RS-BA1, you need this setting.
Internet Access Line (Valid after Reboot)
Selects the your internet access line type.
Only when you configure the remote control system using an optional RS-BA1 through the Internet, you need this setting.
Network User1 ID
Register the Users ID to allow them to remotely access the IC-7700. The IC-7700 can register three users to Network User1 ID to Network User3 ID.
Only when you configure the remote control system using an optional RS-BA1, you need this registration.
The IC-7700 verifies the User ID and password when Remote stations attempt to access the transceiver. If the User ID or password is incorrect, the Remote station cannot access the transceiver.
DIMATIKAN
Turn the transceiver power OFF then ON to make the setting effective.
50001
Turn the transceiver power OFF then ON to make the setting effective.
50002
Turn the transceiver power OFF then ON to make the setting effective.
50003
Turn the transceiver power OFF then ON to make the setting effective.
FTTH
·FTTH
:FiberToTheHome
·ADSL/CATV:ADSLorCabletelevision
Turn the transceiver power OFF then ON to make the setting effective.
z Push [EDIT] F-5 to enter the User ID Edit mode.
x Rotate the main dial to input a User ID of up to 16 characters.
·Push[ABC](MF6)or[abc](MF6)totoggleupperand lower case letters.
·Push[123](MF7)or[Symbol](MF7)totogglebetween numerals and symbols.
·YoucannotregisterthesameIDwithUser2orUser3, if the ID is already registered.
·Push[t] F-1 or [u] F-2 for cursor movement.
·Push[DEL] F-3 to delete the selected character.
c Push [SET] F-5 to set.
V2.00
26
A-6937-2EX
Others set mode (continued) Password
Register the password for the Network User1 ID.
Administrator Selects the administrator setting YES or NO for Network User1 ID. (default: NO)
Network User2 ID Register the Users ID to allow them to remotely access the IC-7700. The IC-7700 can register three users to Network User1 ID to Network User3 ID.
Only when you configure the remote control system using an optional RS-BA1, you need this registration.
Password Register the password for the Network User2 ID.
Administrator Selects the administrator setting YES or NO for Network User2 ID. (default: NO)
Network User3 ID Register the Users ID to allow them to remotely access the IC-7700. The IC-7700 can register three users to Network User1 ID to Network User3 ID.
Only when you configure the remote control system using an optional RS-BA1, you need this registration.
Password Register the password for the Network User3 ID.
Administrator Selects the administrator setting YES or NO for Network User3 ID. (default: NO)
z Push [EDIT] F-5 to enter the Password Edit mode.
x Rotate the main dial to input a Password of 8 to 16 characters, case-sensitive.
·Atleasttwodifferentcharactersmustbeused. ·Push[ABC](MF6)or[abc](MF6)totoggleupperand
lower case letters. ·Push[123](MF7)or[Symbol](MF7)totogglebetween
numerals and symbols. ·Push[t] F-1 or [u] F-2 for cursor movement. ·Push[DEL] F-3 to delete the selected character. c Push [SET] F-5 to set.
TIDAK
When this item is set to “YES,” the Remote station can terminate a connection between another Remote station and the IC-7700.
See the Network User1 ID on the previous page for setting details.
·YoucannotregisterthesameIDwithUser1orUser3,if the ID is already registered.
See the Password of Network User1 ID above for setting details.
TIDAK
When this item is set to “YES,” the Remote station can terminate a connection between another Remote station and the IC-7700.
See the Network User1 ID on the previous page for setting details.
·YoucannotregisterthesameIDwithUser1orUser2,if the ID is already registered.
See the Password of Network User1 ID above for setting details.
TIDAK
When this item is set to “YES,” the Remote station can terminate a connection between another Remote station and the IC-7700.
V2.00
27
A-6937-2EX
Others set mode (continued)
Network Radio Name Enters the Network Radio name of up to 16 characters. The name displays on an RS-BA1’s Remote Utility. DO NOT use the duplicated name on your network.
Only when you configure the remote control system using an optional RS-BA1, you need this registration.
Network AF Sample Rates Selects the limitation of the received audio sampling rate that Remote stations can adjust.
8 kHz, 12 kHz, 16 kHz, 24 kHz and 48 kHz are selectable. (default: 16 kHz)
Codecs Sets the received audio codecs that Remote stations can adjust.
Network MOD Use Selects whether or not to allow Remote stations to send the modulation audio. (default : ON)
Sample Rates Selects the limitation of the modulation audio sampling rate that Remote stations can adjust. 8 kHz, 12 kHz, 16 kHz, 24 kHz and 48 kHz are selectable. (default: 8 kHz)
Codecs Sets the transmit audio codecs that Remote stations can select.
IC-7700
z Push [EDIT] F-5 to enter the Network Radio Name Edit mode.
x Rotate the main dial to input a Network Radio Name of up to 16 characters.
·Push[ABC](MF6)or[abc](MF6)totoggleupperand lower case letters.
·Push[123](MF7)or[Symbol](MF7)totogglebetween numerals and symbols.
·Push[t] F-1 or [u] F-2 for cursor movement. ·Push[DEL] F-3 to delete the selected character. c Push [SET] F-5 to set.
8kHz, 12kHz, 16kHz
Lebih tinggi sampling rates will improve the audio quality. However, they also increase the amount of data, which can cause voice delay or jumpiness, depending on the network condition. Lower sampling rates will decrease the audio quality. However, they also decrease the amount of data.
LPCM 8bit, u-law 8bit, LPCM 16bit
LPCM 8 bit, u-law 8 bit and LPCM 16 bit are selectable. (default: LPCM 8bit, u-law 8bit, LPCM 16bit)
ON
·ON: The Remote stations send the modulation audio.
·OFF:TheRemotestationsdonotsendthemodulation audio.
8kHz
Lebih tinggi sampling rates will improve the audio quality. However, they also increase the amount of data, which can cause voice delay or jumpiness, depending on the network condition. Lower sampling rates will decrease the audio quality. However, they also decrease the amount of data.
LPCM 8bit, u-law 8bit, LPCM 16bit
LPCM 8 bit, u-law 8 bit and LPCM 16 bit are selectable. (default: LPCM 8bit, u-law 8bit, LPCM 16bit)
V2.00
28
A-6937-2EX
Remote jack (CI-V) information
D Jadual arahan
Cmd. Sub Cmd. Data Description
18
00
HIDUPKAN transceiver.
01
MATIKAN transceiver.
This command is available only when the transceiver is standby mode. 1A 05 0032 00 to 03 Send/read MOD input connector during DATA OFF (00=MIC; 01=ACC; 02=MIC/ACC; 03=S/P DIF; 04=LAN)
0033 00 to 03 Send/read MOD input connector during DATA1 (00=MIC; 01=ACC; 02=MIC/ACC; 03=S/P DIF; 04=LAN)
0034 0035
00 hingga 03 00 hingga 03
Send/read MOD input connector during DATA2 (00=MIC; 01=ACC; 02=MIC/ACC; 03=S/P DIF; 04=LAN)
Send/read MOD input connector during DATA3 (00=MIC; 01=ACC; 02=MIC/ACC; 03=S/P DIF; 04=LAN)
0129 05 to 15 Send/read voice memory normal record
time (05= 5 sec. to 30=30 sec.)
0191 00 to 06 Send/read APF AF level.
(00=0dBto06=+6dB)
0192 0000 to Send/read LAN MOD output level
0255 (0000=0% to 0255=100%)
0193 00 to 05 Send/read the TX Delay setting (HF)
(00=OFF, 01=10 ms, 02=15 ms,
03=20 ms, 04=25 ms, 05=30 ms)
0194 00 to 05 Send/read the TX Delay setting (50M)
(00=OFF, 01=10 ms, 02=15 ms,
03=20 ms, 04=25 ms, 05=30 ms)
0195 00, 01 Send/read the Shutdown function.
(00=Shutdown, 01=Standby/Shut-
ke bawah)
0196 0000 to Send/read the transceive CI-V Ad-
0223 dress for LAN to REMOTE in hexa-
decimal code.
(0000=00h to 0223=DFh)
0197
Send/read the default gateway set
(0000000000000001=0.0.0.1 to 0255
025502550254=255.255.255.254, or
FF=Blank)
0198 00, 01 Send/read the remote control capabil-
ity. (00=OFF, 01=ON)
0199 000001 to Send/read the control port setting by
065535 accessing from internet.
(000001=1 to 065535=65535)
0200 000001 to Send/read the serial port setting by
065535 accessing from internet.
(000001=1 to 065535=65535)
0201 000001 to Send/read the audio port setting by
065535 accessing from internet.
(000001=1 to 065535=65535)
0202 00, 01 Send/read the internet access line
tetapan.
(00=FTTH (Fiber To The Home),
01=ADSL/CATV)
0203 see p. 30 Send/read Network radio name
(up to 16-character)
0204 00 to 04 Send/read the maximum AF sample
rates for remote stations.
(00=8 kHz, 01=12 kHz, 02=16 kHz,
03=24 kHz, 04=48 kHz)
Cmd. Sub Cmd. Data Description
1A 05 0205 00 to 02 Send/read the AF codecs for remote
stesen.
(00=LPCM 8bit,
01=LPCM 8bit, u-law 8bit,
02=LPCM 8bit, u-law 8bit, LPCM 16bit)
0206 00, 01 Send/read the network TX audio set-
ting for remote stations.
(00=MATI, 01=HIDUP)
0207 00 to 04 Send/read the maximum modulation
sample rates for remote stations.
(00=8 kHz, 01=12 kHz, 02=16 kHz,
03=24 kHz, 04=48 kHz)
0208 00 to 02 Send/read the modulation codecs for
remote stations.
(00=LPCM 8bit,
01=LPCM 8bit, u-law 8bit,
02=LPCM 8bit, u-law 8bit, LPCM 16bit)
0209 00, 01 Send/read the waveform outline indi-
cation on the spectrum scope.
(00=Fill,01=Fill+Line)
0210 see p. 30 Send/read the waveform outline color
for receiving signal.
0211 00, 01 Send/read the waterfall display on the
Spectrum scope. (00=OFF, 01=ON)
0212 00 to 07 Send/read the peak color level for
displaying the waterfall.
00=Grid 1, 01=Grid 2, 02=Grid 3,
03=Grid 4, 04=Grid 5, 05=Grid 6,
06=Grid 7, 07=Grid 8
0213 00, 01 Send/read waveform type on the
Audio FFT scope.
(00=Fill, 01=Line)
0214 see p. 30 Send/read waveform color for Audio
FFT scope.
0215 00, 01 Send/read the waterfall display on the
Audio FFT scope. (00=OFF, 01=ON)
0216 see p. 30 Send/read waveform color for Audio
Oscilloscope scope.
0217 00, 01 Send/read the voice 1st menu.
(00=VOICE-Root, 01=VOICE-PLAY)
0218 01 to 15 Send/read the repeat interval to
transmit the recorded voice audio.
(01=1 sec. to 15=15 sec.)
0219 00, 01 Send/read the recording mode.
(00=TX&RX, 01=RX Only)
0220 00, 01 Send/read the squelch status for the
RX voice audio recording
(00=Always, 01=Squelch Auto)
0221 00, 01 Send/read the QSO audio record file
Split function setting.
(00=MATI, 01=HIDUP)
0222 00, 01 Send/read the PTT Automatic Re-
cording function setting.
(00=MATI, 01=HIDUP)
0223 00 to 03 Send/read QSO PLAY Skip time.
(00=3 sec., 01=5 sec., 02=10 sec.,
03=30 sec.)
21
00 see p. 30 Send/read RIT frequency.
01
00, 01 Send/read RIT setting.
(00=MATI, 01=HIDUP)
02
00, 01 Send/read TX setting.
(00=MATI, 01=HIDUP)
V2.00
29
A-6937-2EX
Remote jack (CI-V) information
D Data contents description
·Colorsetting
Command : 1A 05 0210, 0214, 0216 qwerty
0XXX0XXX0XXX
R (Red) 00000255
G (Green) 00000255
B (Blue) 00000255
·RITfrequencysetting
Command : 21 00
X
X
X
X
XX
10 Hz: 09 1 Hz: 09 1 kHz: 09 100 Hz: 09
00: + (tambah) 01: (tolak)
·CodesforNetworkRadionamecontents
Command : 1A 05 0203 – Character’s code– Number
Kod ASCII aksara Kod ASCII aksara
0
30
– Character’s code– Alphabetical characters
Kod ASCII aksara Kod ASCII aksara
AZ
41A
az
61A
– Character’s code– Symbols
Perwatakan
! $ & ” ` +
. : = > ) ] } _ @
Kod ASCII
21 24 26 22 60 2B 2A 2E 3A 3D 3E 29 5D 7D 5F 40
Perwatakan
# % ? ‘ ^ – / , ; < ( [ { | ¯
Kod ASCII
23 25 3F 27 5E 2D 2F 2C 3B 3C 28 5B 7B 7C 7E
V2.00
30
A-6937-2EX
Dokumen / Sumber
| Icom IC-7700 HF/50MHz Transceivers [pdf] Manual Arahan i7700, A-6937-2EX, IC-7700 HF 50MHz Transceivers, IC-7700, HF 50MHz Transceivers, Transceivers |