Giorbello BAEeX7o9VLA Gvidilo pri Instalado de Vitra Kahelo

Enhavo kaŝi

1 CERAMIC TILE INSTALLATION GUIDE

1.1 1 Surface Preparation

1.2 2 Aranĝo

1.3 3 Applying Adhesive

1.4 4 Cutting Tile

1.5 5 Setting Tile

1.6 6 Grouting Joints

2 Dokumentoj/Rimedoj

2.1 Referencoj

3 Rilataj Afiŝoj

CERAMIC TILE INSTALLATION GUIDE

1
Surfaca Preparado

Giorbello BAEeX7o9VLA Glass Tile 3

Giorbello BAEeX7o9VLA Glass Tile - 1 Ensure the surface is clean, dry, and level. Use cement backer boards for added stability.

Giorbello BAEeX7o9VLA Glass Tile - 2 Repair any damaged or uneven areas to create a level base. Remove any moldings, trim, and appliances that could interfere with the installation.

Giorbello BAEeX7o9VLA Glass Tile - 3 Trim door jambs if needed to allow tiles to fit snugly underneath.

2
Aranĝo

Giorbello BAEeX7o9VLA Glass Tile 4

Giorbello BAEeX7o9VLA Glass Tile - 1 Mark the wall’s center with a vertical line. Lay out loose tiles from this line to check spacing.

Giorbello BAEeX7o9VLA Glass Tile - 2 If cuts are smaller than half a tile, adjust the center line.

Giorbello BAEeX7o9VLA Glass Tile - 3 Find the floor’s lowest point, stack two tiles there, and mark a horizontal line across the walls to guide your first row.

3
Aplikante Adhesive

Giorbello BAEeX7o9VLA Glass Tile 5

Giorbello BAEeX7o9VLA Glass Tile - 1 Uzu latex-modified thin-set mortar compatible with ceramic files.

Giorbello BAEeX7o9VLA Glass Tile - 2 Follow adhesive instructions and do not prepare more than 30 minutes of work.

Giorbello BAEeX7o9VLA Glass Tile - 3 Apply a 1/4″ layer with the trowel’s flat side.

4
Tranĉa Kahelo

Giorbello BAEeX7o9VLA Glass Tile 6

Giorbello BAEeX7o9VLA Glass Tile - 1 Uzu a wet saw with a diamond blade for clean cuts.

Giorbello BAEeX7o9VLA Glass Tile - 2 Measure and mark tiles, using a tile cutter for straight cuts and a nipper for curves.

Giorbello BAEeX7o9VLA Glass Tile - 3 Cut the tile slowly and steadily, applying consistent pressure to avoid chipping or breakage.

5
Agordi Kahelo

Giorbello BAEeX7o9VLA Glass Tile 7

Giorbello BAEeX7o9VLA Glass Tile - 1 Start tiling from the room’s center, completing each grid section fully.

Giorbello BAEeX7o9VLA Glass Tile - 2 Place tiles with a twisting motion for good adhesion.

Giorbello BAEeX7o9VLA Glass Tile - 3 Use spacers to maintain even gaps and install perimeter tiles last, leaving a 1/4″ gap at walls.

6
Grouting Joints

Giorbello BAEeX7o9VLA Glass Tile 8

Giorbello BAEeX7o9VLA Glass Tile - 1 Uzu sanded grout for joints over 1/8″ and non-sanded grout for narrower joints.

Giorbello BAEeX7o9VLA Glass Tile - 2 Mix the grout as directed and press it into joints with a float at a 45-degree angle.

Giorbello BAEeX7o9VLA Glass Tile - 3 Wait 24 hours after setting tiles. After drying, buff off the grout haze with a cloth and allow the grout to cure completely before using the area.