Nothing Special   »   [go: up one dir, main page]

0% encontró este documento útil (0 votos)
307 vistas128 páginas

Manual de Enchapadora

Descargar como pdf o txt
Descargar como pdf o txt
Descargar como pdf o txt
Está en la página 1/ 128

Edgebander

Instruction Manual

XM200115
20150710
Table of Content
1. General information …………………………………………………………………………..…….. 1
2. Safety precautions. …………………………………………………………………………………. 3
3. Machine information ……………………………………………………………………………….. 4
3.1 Specifications (standard & optional equipment)………………………………………..… 5
3.2 Machine Structure.………………………………………………………………………………………. 6
4. Installation………………………………………………………………………………………………… 7
4.1 Assembling of detached parts……………………………………………………………………… 7
4.2 Compressed air supply connection …………………………………………………………… 7
4.3 Electrical connection ……………………………………………………………………………………. 8
4.4 Control panel………………………………………………………………………………………………… 9
4.5 Connection for dust collectors……………………………………………………………………… 10
4.6 Chain Feeding Setting…………………………………………………………………………………. 10
5. Operation …………………………………………………………………………………………………… 11
5.1 Edge feeding…………………………………………………………………………………………………. 11
5.2 Pre-milling unit…………………………………………………………………………………………….. 11
5.3 Glue pot setting……………………………………………………………………………………………. 12
5.4 Guillotine knife setting……………………………………………………………………………….. 14
5.5 Pressure rollers …………………………………………………………………………………………… 14
5.6 End trimming……………………………………………………………………………………………… 14
5.6.1 End trimming unit - Protruding edging setting…………………………………… 15
5.7 Trimming unit combination………………………………………………………………………… 15
5.7.1 Adjusting height (protruding edge settlement) …………………………………… 16
5.7.2. Radius trimming (cutting depth settlement) ……………………………………… 16
5.8 Radius scraping unit …………………………………………………………………………………… 17
5.9 Buffering unit setting………………………………………………………………………………….. 17
5.10 Workmanship sequences………………………………………………………………………….… 19
6. Maintenance & Service………………………………………………………………………………… 20
6.1 Changing the glue………………………………………………………………………………………. 20
6.2 Changing the blades ……………………………………………………………………………………. 21
6.2.1 End Trimming Blade replacement …………………………………………………….. 21
6.2.2 Flushing trimming blade replacement……………………………………………….. 22
6.2.3. Radius scraping replacement …………………………………………………………… 23
6.2.4. Pre-milling unit…………………………………………………………………………………. 23
6.3 Lubrication & Cleaning……………………………………………………………………………..… 23
6.4 Replacement of fuses…………………………………………………………………………………… 24
6.5 Trouble shooting………………………………………………………………………………………… .. 25
7. Pneumatic diagrams & Wiring diagrams ………………………………………………………
8. Spare parts list
INSTRUCTION MANUAL FOR MAX 350

1. General information
For any problems regarding the machine, please contact the local retailer or service assistance
department supplying the following information:
 Machine model number
 Serial number
 Purchase date
 Approximate number of working hours
Effect only adjustments and maintenance operations on machine as indicated in this manual.
Machine Performances
The Max 340 has the function to edge band straight panels with automatic feed and spread glue
directly on panels with edges, between a thickness of 0.4 and 3mm.
Front and rear trimming cut-off can be made together with flush trimming and buffing unit (opt) on
both sides of work-piece.
The machines are made exclusively to execute above functions within the dimensions of the technical
characteristics specified.
When using the Max 330 it is advisable to use good compressed air and dust collection system Flush
trimming is the only operation which gives dust emission. Connect the machine to an efficient dust
collector system which guarantees a suction outlet at least a 20 mt/1”.
Lifting and transport
Preferably use a forklift or trans-pallet to handle transport of machine, since its frame allows their
use.
To avoid any accidents during transport make sure that the machine is firmly secured to the forklift
with ropes or other suitable systems.
The machine can be lifted with ropes, belts or slings, adequate to the machine weight, and hooked on
as shown.

1
INSTRUCTION MANUAL FOR MAX 350

Location of machine
The machine is delivered with a thermal shrinked nylon protection for transport, some parts of the
machine are detached.
Locate the machine in a suitable place, considering the overall dimensions of the machine, space
needed for stacking, loading and offloading work-pieces leaving sufficient space for the operator.
The machine base must be lay on a solid surface and well leveled.
Use a water level (or other good quality level) to check the working table is leveled in both direction.
Tolerance +- 0.25mm in longitudinal direction. It is possible to fix the machine to the floor by screwing
the 4 holes made on the bottom of the base.
Operator’s position
The operator’s position, can reach all operating and emergency controls with the maximum ease and
practicality.
The caution area in indicates the space which must be left free around the machine for cleaning
purposes, maintenance and normal use.

Noise Levels
As per ISO3744/94-ISO 7960/95 Annex norms:
When working with dust tractor
AVG 73.6 (dB (A)), OpE 73.1 (dB (A)) OpU 73.7 (dB(A))
Description of symbols:
AVG: Medium level of acoustic pressure
OpE Level of acoustic pressure of operator’s entrance place
OpU level of acoustic pressure of operator’s exit place

2
INSTRUCTION MANUAL FOR MAX 350

2. Safety Precautions
- Before operating machine, read the instruction manual carefully, taking note of all recommended
safety precautions.
- This machine has been built to give the best possible results with the maximum safety.
- Your safety is your responsibility. Serious risks are involved when working with machinery always
keep this in mind.
- Always focus on the job being done, do not operate machine when tired.
- Never use in dangerous environment such as in damp, wet location, expose under rain.
- Never leave machine running without attention.
- Never open the protection cover while the machine is still running.
- The machine operator must not be younger than the minimum age established by legislation and
must also be fully qualified to work with this machine.
- Many accidents are caused by appropriate clothing and personal objects (i.e. bracelets, watches,
necklaces etc). Make sure that buttons are securely fastened. Do not wear ties and tie back long
hair.
- Wear approved footwear and safety glasses for your eyes at all time.
- The machine and working area around it must always be kept clean, keep well lighted and
ventilation.
- Use the machine only for the type of workmanship it has been built for.
- The use of safety devices is obligatory and must never be removed, modified or damaged. The
manufacturer declines all responsibility if safety devices are modified in any way.
- In exceptional working conditions the safety devices provided with the machine may be
insufficient. It is your responsibility to make and fit the necessary additional safety devices.
- All work on electrical components must be carried out by a qualified electrician.
- All maintenance work must be carried out with the machine switched off (main switch on
“O”) ,padlocked , the compressed air tube disconnected from the fast snap-on fitting. Make sure
that the machine is switched on again by a qualified and authorized person.
- Make sure that the tools are well-sharpened and are well- balanced.
- Use only cutting tools in good condition. In any case avoid using a hammer.
- Screws, nuts and blots must be tightened with a proportional strength, neither too slack nor too
tight. Use only the tools given just as they are without altering their strength. Never use a hammer
to unlock or block the tools.

3
INSTRUCTION MANUAL FOR MAX 350

3. Machine Information
3.1 Specifications (standard & optional equipment)
Working table height 850MM
Extensible support width 560MM
Panel thickness (min/max) 8/45
Edge thickness (min/max) 0.4~3mm /
Automatic belt feeder speed 9 mt/1’
Pre-milling unit rotation speed 12000 RPM
End trimming unit rotation speed 12000 RPM
Flush trimming unit rotation speed 12000 RPM
(T.C.T) cutters Ø75mm Z4 R=2mm
Dust collection outlet Ø5"
Glue pot elements 1315W
Total power installed 7.7KW
feeding motor 0.75KW
glue & edge 0.18kw
heating elements 5pcs for1.315kw
heating in -feed fence 0.4kw
end trimming motor 0.22KW
flush trimming motor 0.37KW*2PCS
Buffereing 0.12x2- 1200mm-3000RPM
Voltage 380-440/50-60/3 , 220-240/50-60/3
Machine dimensions 3450(L)x660(W)x1850(H)mm
Packing dimensions 2882(L)x760(W)x1365(H)mm

Standard and optional equipment


 Pre-milling unit
 Application of edge up from 0.4mm to 3mm thickness in coil
 Automatic panel belt feeder
 Numerical panel thickness indicator
 Adjustable in-feed fence (to compensate edge thickness)
 Edge feeding by panel
 Glue pot, Teflon coated, 5 electric heating elements and motorized glue spreader
 2 pressure rollers: 1st floating, large diameter, 2nd chromed
 Automatic front/rear end trimming with circular saw blades and tracing pads
 Flush trimming unit with copying pads (top-bottom) cutter-blocks Z4 10000 RPM with disposable
cutters combined 12° bevel/radius 2mm and numerical indicators

4
INSTRUCTION MANUAL FOR MAX 350

 2000mm working table with sliding rollers and PE guide


 Front extensible support for large panels
 Tape coil roller support Ø800mm
 Rear closure with centralized dust collector Ø100mm
 Compressed air regulation unit with filter
 Service tools (wrenches)
 Heatable in-feed fence
 Buffing unit
 Copy roller discs for flush trimming Ø100mm (top-bottom)
 Wheels to move machine (Optional)
Due to needs of continues improvement; specifications are subject to change without prior notice.

5
INSTRUCTION MANUAL FOR MAX 350

3.2 Machine Structure

1. Control Panel 2. Adjust Handle (panel thickness) 3. Feeding stopper 4. Coil support with plate fence
5. Power switch 6. Heavy duty feeding chain 7. Extendable support frame 8. Machine frame
9. Edge feeding point 10. Guillotine unit 11. Glue pot 12. Pressure rollers
13. End trimming unit 14. Flush trimming unit 15. Radius scraping unit 16. Buffering unit
17. Dust collecting point 18. Emergency button 19. Pre-milling unit 20. Adjust for Pre-milling thickness
21. Machine rear cover 22. Electronic box 23. Feeding train motor

6
INSTRUCTION MANUAL FOR MAX 350

4. Installation
4.1 Assembling of detached parts
1. For transport the tape coil support can be detached
from the machine and delivered separately. (fig. 4.1)
2. Fix the plate A to the machine table with the 2
screws D.
3. Place the tape coil support B on plate A placing the
nuts in their correct position then tighten the screw
C.
The assembling and adjustment of above parts is not
difficult, since they have already been tested and
adjusted before leaving the factory.
 It could occur though, that when moving these parts
Fig. 4.1
the adjustments could be altered. However, it is
possible that these adjustments altered in transit.
 Be sure the glue pot is locked for transportation.
 Before using the machine unlock the glue pot by unscrewing the black plastic nut. Do not
unscrew it completely.
 The black plastic nut is to adjust the spring of the glue pot (by screwing it or by unscrewing it)
can be used to move the glue pot forward and backward.

4.2 Compressed air supply connection


The filter /pressure regulator with outflow of condensation also
the quick fitting are situated inside the base of the machine. A (fig.
4.2.1) Ensure that compressed air is at least 7 kg/cm² and that is
free from humidity and has been suitably filtered.
ALWAYS CONNECT THE MACHINE TO THE COMPRESSED AIR UNIT
The air pressure regulator is set at 7 kg/cm² B (fig 4.2.2). Fig. 4.2.1
The machine is equipped with an air pressure switch adjusted at 4
bar. See pag.26 With pressure less than 4 bar you cannot switch
on the machine (you cannot start up machine) Before proceeding
to any maintenance operation, it is necessary to switch off
machine, padlock it and also disconnect the compressed air
system by taking off the fast snap-on fitting.

Never lubricate the pneumatic plant


The pneumatic plant does not need any type of lubrication.
Lubrication oils can damage some of the pneumatic components.

Fig. 4.2.2
INSTRUCTION MANUAL FOR MAX 350

Therefore the lubrication, in particular with some types of oils, can seriously damage and compromise
the functioning of the machine.
Never add lubrication oils in the condensation collecting cup.
The condensation out flow is sufficient to push the tap C upwards (fig. 4.2.2) with the filter/regulator
under pressure.

4.3 Electrical connection


WARNING: WORK ON ELECTRICAL FITTINGS MAY ONLY BE CARRIED OUT BY QUANLIFIED PERSON.
SERIOUS INJURY MAY OCCURRED WHEN LACK OF ATTENTION.
Check that the voltage and the power frequency available correspond
on the
machine name plate on the machine frame.
For 380V/3PH
1. Open the wiring box (fig.4.3.1) to connect the cables as shown.
2. Connection 380/3, cable with 5 wires (3 phase , 1 neutral, 1 earth).
The 3 phases to L1,L2,L3 , neutral to N, Earth to PE.
3. Use a cable adequate for the total power installed.
4. Close the wiring box. Fig. 4.3.1
For 220V/1PH
1. Open the wiring box (fig.4.3.2) to connect the cables as shown.
2. Connection 220/1, cable with 3 wires (2 line, 1 earth). The 1 phase
to L1,L2, Earth to PE.
3. Use a cable adequate for the total power installed.
4. Close the wiring box.
Check the direction of rotation
 Wait until the glue pot reaches 170 C°
 Start-up the feeding with a slight impulse using the On-Off Switch
E ( fig. 4.4.1) Start up the belt of the conveyor. Fig. 4.3.2
It must turn in the same direction as the panel feed. If it does not then you must switch over two of
the three phases (L1, L2, L3 380/3)( fig.4.3.2)
Never connect the neutral to the earth and L1, L2, L3.
WARNING: a wrong connection (for instance inverting a phase with the neutral or not connecting the
neutral) can caused damages irreparably such as heating elements and motors.

 The main power system must be provided with a neutral and efficient earth line. For any
intervention regarding fuses overload cutout, you must reach the electrical box. For maximum
safety during these operations, the main power supply must be switched off.

8
INSTRUCTION MANUAL FOR MAX 350

4.4 Control Panel


An optimized program is installed into the PLC it is useful to check the function of the machine and
the cycles.
The PLC manages
 thermoregulation of the glue pot
 starting stopping of all the motors (fig.4.4.1)

Thermoregulator controls the temperature of the glue pot


 Stand by temperature (set at 170° C)
 working temperature (set at 190° C)

Selectors On/Off (fig.4.4.1)


A. ON/OFF button of Heatable in-feed fence
B. ON/OFF button of front rear end trimmer.
C. ON/OFF button of Edge guillotine from the coil.
ON: edge in coils and cut off edges in strips.
D. ON/OFF button of Pre-milling unit

Start/Stop buttons for the unit (fig.4.4.1)


E. ON/OFF button of Pre-milling unit
Fig. 4.4.1
F. ON/OFF button of the motor of the panel chain
feeder
G. ON/OFF button of end trimmer
H. ON/OFF button of flush trimmers
I. ON/OFF button of buffering unit
J. OFF Stops all the functions started
K. Standby mode
Emergency stop button (fig.4.4.1)
This button immediately stops all machine functions.
Once pushed it remains in locked position, to re-set it, please pull.

Safety electric emergencies


The machine is equipped with 2 electrical emergency contacts. If one of these is opened, then motors
on all units are stopped and the pneumatic system is emptied. The glue temperature remains
unvaried.

2 electrical emergencies situations are:


1. Red safety button on control panel
2. Opening of panel feeder

9
INSTRUCTION MANUAL FOR MAX 350

4.5 Connection for dust collectors


 Check air speed before putting machine into first time operation and after any changes
 Setup of dust collector should be controlled before first time operation. Check daily for the
defects and monthly for the efficiency.
 Connect the dust collector to the machine with unison manner when operating.
 Dust collecting hoses must be electrically conductive and grounded to avoid electrostatic build
up

4.6 Chain Feeding Setting


1. Check the panel thickness first. (NOTE: if panel thickness is set incorrectly, the working cycle is
changed and the workpiece may be damaged.)
Safety device will switch machine off if the machined panel is thicker than thickness ser value.
If the panel is thinner than set thickness value, it may damage the machine or result poor gluing
2. Turn the winding handle to position the pressure bar (you can check the value from the display set
with winding handle)
3. Make sure the height of upper flush trimmer, upper scraper and upper buffer unit regulate
themselves are adjusted to the same when the height of pressure bar is changed.

Panel
thickness

10
INSTRUCTION MANUAL FOR MAX 350

5. Operation
5.1 Edge feeding
 This unit has the function to feed
through the edge and make it meet
the work-piece in front of the first
pressure roller.
1. Check the edge thickness and height.
2. Feed the edge into the guide A (Fig.
5.1.1), then adjust guide with knob A1
and A to the proper gap & height
based on thickness & height & edging
material. (make sure edge can be fed
with no resistance)
3. Move the pressure roller away by Fig. 5.1.1
using handle B (Fig. 5.1.1). Edge NOTE: Adjusting A1 to fix edge is
should be threaded through right up important especially for thin edge
to cutting side of guillotine knives.
4. Release the handle to fix edge on the set
position.
5. Adjust the knob C (Fig. 5.1.1) to the proper
height to avoid edge move up in front of
guillotine knives. (make sure edge can be fed
with no resistance)
 When a new edge band is used, the leading
end of the coil has to be put in manually
passing between the plastic roller E and
rubber roller F (Fig. 5.1.1) until it reaches the
cutting-shear point and goes a few mm Fig. 5.1.2
beyond it to reach the edge band fences G-H (Fig. 5.1.2).
Fig. 5.1.2 The bottom fence H represents the sliding guide of the low edge band level, while the
fence G must be adjusted with knob I to adapt the different edge band heights, leaving the edge
band free to slide. Verify that the vertical play of the edge is within 0.5mm.
 During the adjustment of the fence G, it is advisable to move the edge back and forth to be sure
that the edge can move freely(Fig. 5.1.2).The plate J is needed to keep the thin edge vertical
while it runs through fences G and H. No adjustment is needed (Fig. 5.1.2).
Workpiece moves over copy roller on the conveyor D (Fig. 5.1.1). This action moves tape feeding
rolled L (Fig. 5.1.3) with gears transmission. So edge feed to the workpiece exactly.
[THE EDGE MAY NOT BEING GLUED PROPERLY IF SET INCORRECTLY.]

11
INSTRUCTION MANUAL FOR MAX 350

5.2. Pre-milling unit


Pre-milling function can remove up to 1mm panel
edge. It removes breakout from the saw, solves
out errors caused by a miss set scribing blade or
bad cutting panel.
This part is covered by the red protecting plate to
provide safe working enviroment and enhance
dust collecting efficiency.
To adjust the thickness you want to pre-milling:
- Turn the knob A (fig. 5.2.1) to the thickness
(mm) you
need

Fig. 5.2.1
5.3 Glue pot setting
WARNING: Turn the machine off and make sure power
was disconnected.
 The glue pot unit spreads the hot melting glue on
the work-piece to be edged.
 Thermo adjustment on the PLC checks the
heating and functioning of the glue pot.
For correct use please follow these instructions.
1. Fill the glue pot to approximately 1cm below edge
of the pot.
Fig. 5.3.1
2. Make sure that the type of glue used is compatible
with the conditions and the technical
characteristics of the machine.
Suggested glues:
Jowat JOWAT 280.30 200°C
Emmebi Internatinal Polybond 3072 200°C
DOURS KS 205 200°C
3. Adjust the electronic thermostat at the temperature
corresponding to the one suggested by the manufacturer
(normally adjusted at 190°C at the factory).
4. The glue spreader starts turning automatically when the

12

Fig. 5.3.1a
INSTRUCTION MANUAL FOR MAX 350

temperature reaches 170°C.The quantity of glue spread can be adjust by turning the knob B.
(turning clockwise increases it, turning counterclockwise decreases it.)
During edging, check the level of the glue in the pot and if
necessary fill to the level as indicated in point no. 1.
 The knob L is used to move the glue pot forward or backward.
It is tightened at factory to avoid damage during transportation.
To use the machine, completely slacken the knob till you reach
the locking nut K (Fig. 5.3.1).
Nut K is adjusted at the factory and its position MUST NOT be
modified for any reason (Fig. 5.3.1)
Fig. 5.3.1b

5.3.1 Glue quantity setting (Fig. 5.3.1)


Turn knob M anti-clockwise: + quantity of glue
Turn knob M clockwise: - quantity of glue
It is advisable to increase the glue gradually when adjusting.
Thermoregulator
With the main switch on “ON” the thermoregulator
commands the heating elements to heat the glue pot up to
temperatures 180°C.
 Once you reached the temperature of 170°C (pre-heat)
(fig.5.3.1d) it is possible to move the glue shaft.

 The display when turn on the main power (fig.5.3.1b)


PV: Shows the actual temperature (fig.5.3.1b)
SV: Shows the set up temperature=190°C (fig.5.3.1b) Fig. 5.3.1c
 To check the pre-heat temperature, press SET button twice,
press one you will see PLC display (fig. 5.3.1d) press SET
button again you can see the on the PV At1 pre-heat
shows on SV 170°C When press SET to leave.
 How to increase or decrease the temperature.

Press the SET let the SV monitor blink, press


button to move the select the numbers to key in press
Fig. 5.3.1d
up/down to increase the temperature.
We suggest to start the edging procedure only when the
glue pot reaches the required temperature of 190°C.
(Depends on the glue you choice temperature is about 190
~200°C).

13
INSTRUCTION MANUAL FOR MAX 350

After adjust to the certain temperature, the control panel will memories the last key in temperature
automatically. If the feeder is not start up, wait for the thermoregulator starts to “standby
temperature”.
Lubrication of glue spreader
Every 30 working hour, the lubrication has to be done with the
grease gun (supplied with machine) see(fig.5.3.1e)by aligning
the nozzle into the hole A (fig.5.3.1e).
Reference brand of the grease : Arexons GC300 .
WARNING: The lack of periodic lubrication can create serious
damage and you will have to replace the glue pot.
To reset the functioning of machine, push the “OFF” button on Fig. 5.3.1e
the control panel for 10 seconds
5.4 Guillotine knife setting (Fig. 5.4.1)
Guillotine knife cut off the edge at a certain distance from
the end of the panel. It is used for ABS, melamine, PVC,
veneer and polyester in coil with diameter of 3mm.
When programmers are set the control panel, it is activated
automatically.

5.5 Pressure rollers Fig. 5.4.1


Pressure rollers make the edge to accrete on the workpiece
better. There are 2 rollers set onto the plate, which has to be
adjusted according the thickness of edge.
1. Place edge pieces (cut from the edge you are going to
use for banding) into the free space between the
adjusting screws A (Fig. 5.5.1). Mount bracket to obtain
the correct contact pressure of the rollers.
2. Tighten the screws A to fix the inserted edge and
avoiding falling down, then the correct edge thickness Fig. 5.5.1
would be set.
CAUTION: If this unit was not set correctly, it may result poor gluing and unsatisfied finished
workpiece. Fig. 5.5.2

5.6 End trimming


End trimming unit is used to cut the excess edge on the
front and rear. It can be turned on with the ON button

and .on the control panel.

14
INSTRUCTION MANUAL FOR MAX 350

It is set with dual blade unit and high frequency motor. It can
do straight cutting (0°). Motor is fitted onto support and
glides on a horizontal guide. It is driven by pneumatic
pistons.
CAUTION: End trimming unit is touched off by a mechanical
limit switch. User must note the tear or wear or dust build
up may effect to limit switch then causing delay. Even just
0.01 second delay, it might bring unsatisfied finishing result.
So the limit switch should be check frequently. (Fig. 5.6.1) Fig. 5.6.1

5.6.1 End trimming unit - Protruding edging setting


CAUTION: put extra attention with the setting description here. The values provided here are
recommended and should be tested by using sample panels.
Distance between feeler pad and saw blade are the factor to define the protruding edge.
This structure is usually set ZERO as factory setting. You may need to re-adjust when the saw blade is
changed or replaced.
Follow below instruction to adjust the protruding edging:
1. Turn the machine off and make sure it can
not be turned on again. Open the rear door
& clean through the feeler pad.
2. Clean through the feeler pad
Spring discs. keeps the pad under tension.
Tension within pads will be increased &
edge cut will be shorter if the 2 screws (Fig.
5.6.2) are screwed tighter. Edge cut will Fig. 5.6.2
leave more edge if the screws are loosened.
3. These 2 screws (at top & bottom Fig. 5.6.2)
must be adjusted by the same amount. If the copying pad is not straight, final result may be poor
and it may also damage the workpiece.
4. Close the sawguard.
WARNING: Be careful when handling the blades to avoid injuring hands and damaging the cutting
edges.
Note See Chapter 6.2.1 for blade changing

5.7 Trimming unit combination

This unit can be turned on with the button.


 The standard equipment includes 2 spindle tools –

15 Fig. 5.7.1
INSTRUCTION MANUAL FOR MAX 350

top, bottom (right/ left) – with 3° slope and a 2 mm radius.


 The dust collecting port has a diameter of Ø5"
 which can be connected to the central dust collector.
 Max. Removable protruding is 2mm per side. Cutters turn
and the panel feeding are in opposite. (Fig. 5.7.1)
 Upper flush trimmer automatically regulates itself while
the tool thickness changing because it is attached to the
pressure bar. Fig. 5.7.2
Note Follow the below factors to choose cutter:
1. Max. weight of each cutter: 250g
2. Max width of the cutter: 20mm
3. Max. diameter: 85mm
4. Spindle diameter 16mm with wedge
5. Max. number of revolutions 12,000rpm.

5.7.1 Adjusting height (protruding edge settlement)


CAUTION: put extra attention with the setting description
here. The values provided here are recommended and
should be tested by using sample panels.
Note this setting was carried out in factory before delivery.
Manual adjustment (standard equipment)
1. Turn the machine off and make sure it can not be
turned on again. Then open the rear door.
2. Release clamping lever A (Fig. 5.7.3)
3. Set cutting depth with vertical knob B
Fig. 5.7.3
4. Tight the clamping lever A
Fig.5.7.4 - Fine adjustment (adjusting molding height)
1. Turn the machine off and make sure it can not be turned
on again. Then open the rear door.
2. This setting is set in factory before delivered
3. Molding height adjusting – Adjusting nut
4. Check the adjustment and repeat when needed.
C – Adjusting nut for flush trimming
D – Adjusting nut for flush and radius trimming mold
Fig. 5.7.4
5.7.2. Radius trimming (cutting depth settlement)
CAUTION: put extra attention with the setting description here. The values provided here are
recommended and should be tested by using sample panels.
Note this setting was carried out in factory before delivery.

16
INSTRUCTION MANUAL FOR MAX 350

1. Turn the machine off and make sure it can not be turned
on again. Then open the rear door.
2. Turn knob A (Fig. 5.7.5) to set the cutting depth
3. Finish this process by close the rear door

5.8 Radius scraping unit


CAUTION: Only use PVC material on this unit and make sure
setting of this unit has to be exact. The workpiece and
Fig. 5.7.5
scraping unit may be damaged if the setting is incorrect or
with unsuitable material.

 The main defined unit to set the radius is the


horizontal copier pad D (Fig. 5.8.1).
To adjust the cut depth:
1. Turn the machine off and make sure it can not be
turned on again. Then open the rear guard.
2. Loosen 2 screws A (Fig. 5.8.1) then adjust the cutting
depth by using knob B. Adjust it until the shown value
match to the thickness of the edge you are using.
Note To compensate the thread backlash, always adjust
the workpiece toward.
3. Tight 2 screws A (Fig. 5.8.1)
4. Repeat the above steps if required after checking.
To move away the scraper:
If you want to move the scraper away from the workpiece, Fig. 5.8.1
turn screw C to disengage the upper & lower scrapers.
5.9 Buffering unit setting
 The buffing unit is used to polish the edge which has just been trimmed or finished with the flush
trimming unit. This unit can be turned on/off with the buffering button on the control panel.
 The rotation speed of the buffers is 3000R.P.M.
 The buffers rotate in opposite direction to the panel movement.
 Standard equipment foresees two buffers, top and bottom, tilt able up to approx. 10°
The parameters to respect in the choice of buffers are the following:
- Maximum diameter permitted 120 mm
- Diameter fixing spindle 20 mm
- Maximum weight for each buffer 200gr.
- Maximum 3000 RPM
Adjustment Top buffer

17
INSTRUCTION MANUAL FOR MAX 350

1. Turn the machine off and make sure it can not be


turned on again. Then open the rear guard.
2. Loosen locking screw A ( fig.5.8.1)
3. Position and /or tilt the buffer into desired position.
Once reached desired position tighten the screw A (fig.
5.9.1)
Adjustment Bottom buffer
1. Turn the machine off and make sure it can not be
turned on again. Then open the rear guard. Fig. 5.9.1
2. Loosen locking screw B( fig. 5.9.2)
3. Position and/or tilt the buffer into desired position
Once reached desired position tighten the screw B( fig.
5.9.2)
WARNING: An excessive quantity of glue which dirtying
the flush trimming unit can also damage the buffers. The
buffers must be adjusted with a slight pressure on the edge
to be polished but an excessive pressure can force motors
and therefore not obtaining an optimum finishing.
Fig.5.9.2
Replacement of buffers
To replace the buffers,
1. Turn the machine off and make sure it can not be
turned on again. Then open the rear guard.
2. Loosen screw A( fig. 5.9.3)
3. Pull out the flange B ( fig.5.9.3)
4. Pull out the buffers
5. Remount a new set of buffers (3) following mounting
scheme in (fig.5.9.3)
6. Tighten well the locking screw A. Fig. 5.9.3
Note Dismount one set of buffers at a time to avoid
switching over their position.
The screw of the bottom buffer is LEFT handed.
Maintenance Cleaning & Lubrication
Check the buffing unit constantly (even a few times per day)
and remove any scraped pieces which could disturb correct
functioning.
Important!! When mount a buffers or adjust the buffer,
adjust the buffer 2/3 forward to touch the work peace, only 1/3 under the fence, this is to avoid too
much of the buffer rub the fence which makes buffer worn or motor too hot.

18
INSTRUCTION MANUAL FOR MAX 350

5.10 Workmanship sequences


It is quite simple to obtain good edge banding results; anyhow it is necessary to keep in mind a good
number of variations, of which each one contributes to the best final results.
The aspects are summarized in 4 groups
1. Work-pieces to be edgebanded 2. Edge bands used
3. Hot melting glues 4. Adjustment of the machine

1) Work-pieces to be edgebanded
 It is advisable to use good quality work-pieces with a sufficient density
 Cutting must be net, without chipping and with a straightness of at least +0.1 mm per linear
meter.
 The area to be edgebanded must be free from dust and humidity.
 The cut must be perfect at (90°) both on surface and in thickness.
 The panel must be stored a the workshop temperature
2) Edge bands used
 Use good quality edge bands.  Keep them in a dry storage place
 Check that manufacturing date is written on  Avoid the use of PVD edge bands of limited
the wrapping (the glue deteriorates with thickness, since they are very difficult to
time) apply.
3) Hot melting glues
 Use hot melting glues suitable for the  Check that the glue is spread uniformly on
machine characteristics and carefully the panel
respect the manufactures specifications
 Effect various test to find the right quantity  The glue must not overflow, otherwise the
of glue, using knob M (fig. 5.2.3) cutters will get stained.
4) Adjustments of machine:
Turn on the main switch and all other functions (see 4.4) and dust outlets system, make some edge
banding tests checking following points:
 Height of panel feeder equal to the  Glue melting temperature (see 5.2)
work-piece thickness
 Sideway push  Work-piece feeding (see 5.1)
 Cutting edge adjustments  Flush trimming unit

Effect any further adjustments with instructions as indicated in respective paragraphs.

19
INSTRUCTION MANUAL FOR MAX 350

6. Maintenance & Service


6.1 Changing the glue
WARNING: Risk of being scalded
1. Turn the machine off and glue pot must to be cold.
2. When the thermoregulator shows approx. 80-90°C,
turn off the main switch.
3. With a wooden stick of approx.4x1 cm pull up one
side of the glue. DO NOT use metal tools (fig. 6.1.1).
Fig.6.1.1
4. Pull the block of glue with a pair of pliers
5. Pay attention not to burn yourself. Pull out the
block (fig. 6.1.2).
6. Wait until the glue pot is completely cold and clean
all glue residues (fig. 6.1.3).
Note1 Do not mix with glue wood shavings or wood
dust.
Note2 To avoid the deterioration of the glue. Always
check the thermostat adjustment and the quantity of Fig.6.1.2
the remaining glue.
Note3 Since good edge finishing depends upon many
factors, such as type of edge, type of work-piece,
cutting quality, environment temperature etc, it is
necessary to affect various tests to find the correct
adjustment.

Fig.6.1.3

20
INSTRUCTION MANUAL FOR MAX 350

6.2 Changing the blades


WARNING: Be careful when handling the blade and knives. Wear protecting gloves to avoid
cutting yourself.
6.2.1 End Trimming Blade
1. Turn the machine off and make sure it can not be
turned on again.
2. Remove the dust collecting hose and 2 screws A (Fig.
6.2.1), loose 1 screw B (Fig. 6.2.1). Then remove the
dust adaptor (Fig. 6.2.2).
3. Use L wrench to fix the motor shaft (Fig. 6.2.3A )
4. Loosen nut C with wrench then remove old blade,
Fig.6.2.1
Flange D, Space Ring E and another old blade each by each (Fig. 6.2.4).
NOTE Be aware of the direction of Flange D & Space
Ring E (Fig. 6.2.4)
5. Set back the new blade, Space Ring E, another piece of
new blade, Flange D back and lock them in position
with nut B (Fig. 6.2.4).
NOTE Be aware of the direction of Flange D &
Space Ring E (Fig. 6.2.4)
WARNING: make sure the blade tooth is set in CORRECT Fig.6.2.2
DIRECTION as scheme (Fig 6.2.5)

Fig.6.2.3A

Fig.6.2.3

Fig.6.2.5 C
D
E
Fig.6.2.4

21
INSTRUCTION MANUAL FOR MAX 350

6.2.2 Flushing trimming unit


1. Turn the machine off and make sure it can not be turned
on again. Remove the compressed air supply system
from the machine and leak the remaining compressed air
out.
2. Use L wrench to loose screw A (Fig. 6.2.5), then pull out
the motor from machine. Put the motor on the working
table.
Fig.6.2.5
3. Use L wrench to fix motor shaft on the motor back side and use another L wrench to loose screw
B (Fig. 6.2.6). Then loosen screw B to take the whole set
of tooling.
4. Loosen set screw C (Fig. 6.2.7, don’t need to take it out).
Then take the knives off.
Note there are 4 sets of knives being set this unit (Fig. 6.2.9).
5. Fit the knives back and tighten set screws to fix them in
position
6. After replacing the knives, fix the whole set of trimming Fig.6.2.6
knife back to the motor with screw B (Fig. 6.2.6).
7. Fix the motor back into machine and push it
Fig.6.2.7
forward while assembling. Then tighten screw A
(Fig. 6.2.5) to fix it in position.
8. Replacing process finished.

Fig.6.2.7A

Fig.6.2.9
Fig.6.2.8

22
INSTRUCTION MANUAL FOR MAX 350

6.2.3 Scraping unit


1. Turn the machine off and make sure it can not be turned
on again. Remove the compressed air supply system from
the machine and leak the remaining compressed air out.
2. Loosen screw A (Fig. 6.2.9) and take the 2 washers out,
then use the L wrench to knock blade B (Fig. 6.2.10) out.
3. Fit the new cutter plate to the blade groove.
4. Set the 2 washers back then tighten the screws to fix Fig.6.2.9
washers & new cutter plate in position.
5. Go through the above same process for replacing the
cutter plate for bottom unit.
6. Finish cutter replacement for scraping unit.

Fig.6.2.10

Fig.6.2.11

6.2.4 Pre-milling unit


Note: Check the blade direction and make sure the direction
of blade is correct after replacing.
1. Use L wrench to fix the shaft then use Round Wrench to
loosen the washers and remove it (fig.6.2.12)
2. Replace the blade with new one then set back the washers
back to the original position. (fig.6.2.13 & 6.2.14)
Note2. Replacing process for both sides are the same but the Fig.6.2.12
blade direction is in contrast

Fig.6.2.13 Fig.6.2.14

23
INSTRUCTION MANUAL FOR MAX 350

6.3 Cleaning & Lubrication


Cleaning
Occasionally machines need to clean. Make main switch set as 0 /OFF and padlock. Disconnect
compressed air power supply tube.
a) Clean the pressure rollers and the small roller on the bed from glue residues, with proper solvent
Note Before touching parts with solvent makes sure that they are cold.
b) Check that in the flush trimming unit dust hoods residues do not pile up.
c) Clean with a solvent the sliding rods of the flush trimming unit and the front cutting –nipper.
Lubrication
WARNING: Before starting any checking, maintenance or lubrication operation, make sure that main
switch is on 0/OFF padlocked and that power supply
tube of compressed air disconnected.
Usually no lubrication is necessary since ball bearings
are tin-plated and lubricated “for-life”. The sliding
bushes are auto-lubricated and the ball bearing
bushes do not need to be lubricated but just clean
properly the sliding rods; anyhow the chain and
pinions of the edge band feeding unit and glue
spreader need to lubricated at least once a year.
Fig.6.3.1
Guillotine unit: see Fig. 6.3.1
Glue pot: See chap. 5.2.1.
6.4 Replacement of fuses
To substitute the fuses it is necessary to make access to the electrical box Fig. 6.4.1 and proceed as
follows:
Replacement of fuses
1. Switch off the main power supply
2. Position the main switch on 0/OFF and padlock it
3. Disconnect the compressed air power supply
tube
4. Unscrew the screws which lock the electrical
panel
5. Open the boxes (Fig. 6.4.1) Fig.6.4.1
6. Replacement the burnt fuses A(Fig. 6.4.1) and
backward repeat above operations.
7. Re-set of overload cutout switches
8. Switch off the main power supply
9. Position the main switch on 0/OFF and padlock it
10. Re-set to ON the overload cutout switches B (Fig. 6.4.1).
If it is still necessary to re-set the switches it is important to verify that:

24
INSTRUCTION MANUAL FOR MAX 350

3. The value set is correct


4. The movement connected to the motors are free to move
5. The motors temperature is not too high (80-90°C)
6. The motors are free to brake circuit
7. the overload cutout switch is efficient
 It is important that a specialized technician checks this out.
Note The access to the electrical box is not foreseen for other operations, but only for special
maintenance to be carried out by a qualified electrician or authorized technical personnel of
manufacture.
6.5 Trouble shooting
P: The display does not light up
C: Main electric cable, fuses, bad connection on
P: the edge is pushed too much at the beginning
main electric cable
and end of panel
S: check cables, fuses, connection
C: too much pressure on first roller
S. adjust the push

P: Pushing start buttons-motors do not turn on


P: Start buttons, motors do not turn on and the
C: Emergencies have not been re-set
display shows:
S: See “Safety Electric emergencies”.
C: 30 working hour of the glue spreader
S: effect maintenance
C: Not reached working temperature
S: Check compressed air and pressure
P: end trim unit does not effect its cycle
C: end trim unit excluded
C: Check the overload protection switches
S: check end trim unit exclusion
S: Check compressed air and pressure

P: motors do not start up , blades do not turn


P: the panel is not feeded linearly
C: emergencies have not bee reset
C: fence not adjusted in regards to edge
S: see “Safety Electric emergencies”
thickness
S: adjust the fence
C: working temperature has not been reached
S: wait to reach correct working temperature
P: The edge is not feeded through properly
C: It has not been inserted between nylon and
C: Overload switches cutout
rubber roller
S: reset the overload switches 4.4
S: See. 5.1

C: check that toothed belt is not damaged


C: the edge fence has not been adjusted in
S: if so, substitute it
height
S: adjust the edge fence
25
INSTRUCTION MANUAL FOR MAX 350

C: not enough pressure on first pressure roller


S: adjust the push

C: entrance fence not correctly adjusted


S: adjust fence is regards to edge thickness see

P: motors do not start up , blades do not turn P: edge chips or is torn/pulled away
C: emergencies have not bee reset C: lowering speed of unit too fast
S: see “Safety Electric emergencies” S: adjust speed see “Pneumatic adjustments

C: working temperature has not been reached P: motor does not start up
S: wait to reach correct working temperature C: emergencies have not been reset
S: see Safety Electric emergencies”
C: Overload switches cutout
S: reset the overload switches C: working temperature has not been reached
S: wait till you reach correct working
C: check that toothed belt is not damaged temperature
S: if so, substitute it
P: motor starts up, belt does not feed through
P: cut is not straight C: the belt is not tensioned correctly
C: the tracing pads are not correctly adjusted S: tension the belt
S: adjust the tracers
P: flush trimming not correct
P: flush trimming of dull edge C: tracers not adjusted in regards to edge
C: tracers not adjusted in regards to edge thickness
thickness S: adjust tracers and/or the axial adjustment in
S: adjust tracers and/or the axial adjustment in regards to edge thickness
regards to edge thickness
C: working temperature has not been reached
P: the motor starts up but the cutter-heads do S: wait till you reach working temperature
not turn or lose their revolutions (R.P.M.) when
flush trimming P: Buffers spread glue on the panel
C: check that belt is not damaged or its tension C: too much glue
S: substitute damaged belt or tension it S: adjust the glue quantity

26
INSTRUCTION MANUAL FOR MAX 350

C: flush trimming of the edge is dull C: probably wrong glue


S: substitute knives S: see Types of glue suggested”

P: side of panel chips P: Buffers wear away the edge in the corners
C: tracers badly adjusted –out of square C: buffers not adjusted correctly
S: adjust the tracers S: adjust buffers position

P: the panel is not pushed against the fences


C: the rubber on the rollers no longer has
adherence
S: clean the rollers

C: the rollers are not sufficiently tilted


S: adjust the rollers

7. Pneumatic Diagram
Note The pneumatic diagrams supplied are only for the use of qualified or authorized technical
personnel of manufacturer.
These diagrams do not authorize you in anyway to change the pneumatic parts or logic functioning.

27
INSTRUCTION MANUAL FOR MAX 350

28
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
*electrical power supply:
A
3~,380~415V,50/60Hz 3Ph,380~415V,50Hz,CE A A A
*recommend breaker capacity: (Please Find your voltage Specifications)
16A<fuse<20A,
L1 L2 L3 N PE L1 L2 L3 N PE
B B B B
L10 L20 L30
QF1
Main FU4,20A
L2
C switch C C L1 C
Limit of equipment N
L2
L11 L21 L31 Power light FU4,20A U1
D D D PE D
200~240V AC MOTOR DRIVE
50/60Hz

E E E E
2.5A-4A KM1 A1 A2
QM1
2.6A Conveyer U V W COM S1
T1 U1 U1
3Ph,380~415V
F T2 V1 V1 M 50Hz F F F
T3 W1 W1 3~ 1HP(0.75kw) KM3
Pin13 Pin14

G G G
KM4 G
Pin13 Pin14

QM2 1A-1.6A KM2 A1 A2 COM S1


1.1A Glue shaft
T1 U2 U2
H 3Ph,380~415V H H KM3 A1 A2 H
T2 V2 V2 M 50Hz 0.63A-1A
QM3
T3 W2 W2 3~ 1/4HP(0.18kW) 1A Front/rear trimming
T1 U3 U3
3Ph,220V
T2 V3 V3 M 200Hz
I I I
T3 W3 W3 3~ 0.3HP(0.2kw) I

KM5 A1 A2 4A-6.3A KM4 A1 A2


QM5 0.63A-1A QM4
0.6A Top Buffing 4.2A Top flush trimming
J T1 U6 U6
3Ph,380~415V
J J T1 U4 U4
3Ph,220V
J
T2 V6 V6 M 50Hz
T2 V4 V4 M 200Hz
T3 W6 W6 3~ 1/6HP(0.12kw)
T3 W4 W4 3~ 1/2HP(0.37kw)

K K K K
Bottom Buffing Bottom flush trimming
U7 U5
3Ph,380~400V 3Ph,220V
V7 M 50Hz
V5 M 200Hz
L W7 3~ 1/6HP(0.12kw)
L L W5 3~ 1/2HP(0.37kw) L

M M M M

N MODEL main control circuit N N MODEL AC MOTOR DRIVE N


DATE 10\07\2014 DATE 10\07\2014
DARWING 1 DARWING 2
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
QCE35001
QCE35001

ITEM PART NO PARTS NAME SIZE Q`TY NOTE


1 722561 Machine frame 1 R
2 722562 Plate 1 R
3 SJ089300 Button Head Screw M8*1.25*12 6
4 WF081820 Washer M8*φ18*t2 6
5 722360 Cover 1 R
6 722369 Plate 1 R
7 WF061620 Washer M6*φ16*2t 8
8 SR060200 Cap Screw M6*1*10 10
9 NH101700 Hex Nut M10x1.5 6
10 WS100000 Spring Washer M10 12
11 WF102730 Washer M10*27*3 8
12 MA722363 Motor 380V 3~ 50HZ 1
MA722363A Motor 220V 3~ 60HZ 1 S
13 722370 Reducer DB32-060-075 1 50HZ
722370A Reducer DB32-075-075 1 S,60HZ
14 SS069200 Set Screw M6*1*8 3
15 722361 Sprocket 1
16 722368 Motor Fixed Bracket 1
17 SH100900 Hex Head Bolt M10*1.5*45 4
18 AB722563 Adjustment Bracket 1 VE
19 722007 Block 162
20 722587 Chain 10B-324 目 1
21 SR069400 Cap Screw M6*16L 8
22 WS060000 Spring Washer M6 10
23 722364 Shaft 2
24 BD251501 Dry Bearing DU25x15 4
25 WF061320 Washer M6*φ13 2
26 722365 Plate 1
27 SJ069200 Button Head Screw M6*1*8 2
28 722366 Cover 1
29 SR040100 Cap Screw M4*0.5*5L 2
30 722363 Plate 1
31 722648 Plate 1
32 SH100500 Hex Head Bolt M10*25 4
33 SR100600 Cap Screw M10*1.5*30 4
34 NL081300 Nylon Nut M8 4
35 RS300000 C-Type Retaining Ring S30 1
36 722354 Shaft 1
37 WF082020 Washer M8*φ20*t2 8
38 SR081600 Cap Screw M8*1.5*80 2
39 722362 Sprocket 1
40 BB600602A Ball Bearing 6006ZZ 2
QCE35001
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
41 722355 Washer 2
42 SG059200 Hex Head Bolt (W/Flange) M5*0.8*8 3
43 721173 Wheel Spindle 2
44 721175 Wheel 2
45 WS080000 Lock Washer M8 1
46 SH089400 Hex Head Bolt M8*16 1
47 BD152001 Dry Bearing DU15x20 4
48 RS150000 C-Type Retaining Ring S15 2
49 722357 Shaft 2
50 WF123030 Washer M12*φ30*t3 2
51 SH120400 Hex Head Bolt M12*1.75*20 2
52 SH089300 Hex Head Bolt M8*1.25*12 2 H
53 WF124030 Washer M12*φ40*t3 2
54 203410 Ring 2
55 SR120700 Cap Screw M12*1.75*35 2
56 IM722002 Motor Cord 0.5mm^2*4C 1 (CE, 380~415V)

IM722022 Motor Cord 20AWG*4C 1 S,(CSA, 220~240V)


QCE35002
QCE35002

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722400A Hand Wheel 1

2 SR050900 Cap Screw M5*0.8*45 1

3 722566 frame 1 T

4 NL050800 Lock Nut M5*0.8 1

5 SS069100 Set screw M6x0.8x6 1

6 722401A Digital position indicator 1

7 722404 Shaft 1

8 SR069300 Cap Screw M6*1*12 4

9 BD201002 DU Bushing DUF20x10 1

10 AB722485 Cylinder ASM. 1

11 SS089204 Set screw M8*8 4

12 994216 Bearing 51104 4

13 722396A Screw 2

14 SS089200 Set screw M8*1.25*8 2

15 722405A precise Nut 2

16 722397 chain wheel 05B-30T 2

17 722406A fixed plank 1

18 SR060500 Cap Screw M6*1*25 8

19 722393 line track 2

20 SR060500 Cap Screw M6*1*25 6

21 WF061310 Washer M6*φ13 3

22 SR060200 Cap Screw M6*1*10 5

23 722383 support plank 1

24 WF061620 Washer M6*φ16 10

25 SR060400 Cap Screw M6*1*20 2

26 AB722399-1 Roller Chain Frame ASM. 1

27 AB722399-2 Roller Chain Frame ASM. 1

28 722633 support plank 1 VE

29 722394 Block 2

30 722395A Screw sheath 2

31 722632 Fix Plate 2

32 722565 plank 1 VE

33 SR050200 Cap Screw M5*0.8*10 5

34 WF051210 Washer M5*φ12 5

35 AB722564 Press beam 1 T,(A)

36 SS069300 Set screw M6*1*12 1

37 722588 Roller Chain 歐規05B-598目 1

38 SR080400 Cap Screw M8*1.25*20 2

39 WF081818 Washer M8*φ18*t1.8 2

40 NF081300 Hex Flange Nut M8*1.25 2


QCE35002

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

41 AB722403C Switch ASM 1

42 AB722403D Switch ASM 1

43 SR060600 Cap Screw M6*1*30 8

44 SR069400 Cap Screw M6*1*16 8

45 AB722403E Switch ASM 1

46 AB722403F Switch ASM 1

47 WF061620 Washer M6*φ16 8

48 SR080900 Cap Screw M8*1.25*45 2

49 WS060000 Spring Washer M6 8

50 NH061000 Nut M6 2

51 SS060200 Set screw M6*1*10 2

52 SM069400 Hex Countersunk Screw M6*16L 4

53 722581 Dust-proof Cover 1

54 722489 Platen 2

55 722491 Telescopic Cover 2

56 722493 EVA 80*8*5T 1

57 NH081300 Nut M8 2

58 AC722495 1

59 WF082030 Washer M8*φ20*3.0T 2


QCE34003A
QCE34003A
ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 NH081300 Hex Nut M8 3

2 722107 Wheel 1

3 BB608002A Ball Bearing 608ZZ 1

4 AC722103 Wheel Spindle 1

5 721176 gear wheel 1

6 722106 felt 35(W)*77"*6(T) 0.011

7 722102 Fixed Flakes 1

8 ST040200F Screw M4*0.7*10 2

9 SR060800 Cap Screw M6*1*40 2

10 SR061000 Cap Screw M6*1*50 2

11 WS060000 Spring Washer M6 6

12 RR220000 C-Type Retaining Ring R22 1

13 RS080000 C-Type Retaining Ring S8 2

14 BD081001 Dry Bearing DU08x10 4

15 NH061010 Hex Nut M6*1(L,H) 1

16 721164 Plate 1

17 722100 Block 1

18 721163 Wheel 1

19 BB600203A Ball Bearing 6002LLU 2

20 SR060500 Cap Screw M6*1*25 2

21 SJ059200 Button Head Screw M5*0.8*8 1

22 WF051210 Washer M5*φ12 1

23 722112 Chrome Rod Park 2

24 SR040200 Cap Screw M4*0.7*10 1

25 722096A Wheel 1

26 WF101605 Washer φ10xφ16x0.5t 1

27 SR059300 Cap Screw M5*0.8*12 1

28 SR061400 Cap Screw M6*1*70 2

29 722105 L-Fixed Flakes 2

30 SS049100 Set Screw M4x0.7x6 2

31 722616 Wheel Bracket 1

32 SR059400 Cap Screw M5*0.8*16 4

33 722614A Fixed Plate 1

34 AB722615A Cylinders ASM. 1

35 WF061620 Washer M6*φ16*2t 2

36 WS060000 SPRING Washer M6 2

37 NH061000 Hex Nut M6 2

38 722091F Plate 1

39 SR069400 Cap Screw M6*1*16 2

40 722098 Block 1

41 722104 Shaft 2
QCE34004A
QCE34004A

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 721240 Plum Nut M10 1

2 NH101700 Hex Nut M10x1.5 2

3 721239 Adjustment Screw M10 1

4 721195 Block 尼龍條 1 現場自裁

5 BD081001 Dry Bearing DU08x10 2

6 WF051320 Washer M5*φ13*2T 7

7 722114A Spring Plate 1

8 722113A Guides 1

9 WF051420 Washer M5*φ14*2t 4

10 WF041010 Washer M4*φ10 1

11 SR0402403 Cap Screw M4*0.7*10 1 合金鋼

12 SS059100 Set Screw M5x0.8x6 1

13 722115 Washer 1

14 722112 Chrome Rod Park 2

15 722111A Plate 1

16 722094 Adjustment Screw 1

17 SR050200 Cap Screw M5*0.8*10 3

18 722095 Plum Nut 1

19 722092 Adjustment Plate 1

20 722093 Adjustment Plate 1

21 SR059400 Cap Screw M5*0.8*16 2

22 NF050800 Flange Hex Nut M5*0.8 2

23 WF051210 Washer M5*φ12*1T 2

24 722092A Adjustment Plate 1

25 722093A Adjustment Plate 1

26 721056 Plum Nut M8 2

27 NH081300 Hex Nut M8 2

28 NF061000 Flange Hex Nut M6 4

29 WF061616 Washer M6*φ16*1.6t 2

30 722097 Shaft 2

31 SR050400 Cap Screw M5*0.8*20 2


QCE34005A
QCE34005A

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 NH061000 Hex Nut M6 1

2 722123B Cutter Plate 1

3 722121A Cutter Fixed Plate 1

4 BD081001 Dry Bearing DU08x10 4

5 722120A Chrome Rod Park L=122MM 2

6 721301 join pin 1

7 NH081300 Hex Nut M8 1

8 722118 Screw 1

9 NH101700 Hex Nut M10x1.5 1

10 AB722117 Cylinders ASM. 1

11 SR061200 Cap Screw M6*1*60 1

12 SR061400 Cap Screw M6*1*70 1

13 SR0594403 Cap Screw M5*0.8*16 2

14 WF051320 Washer M5*φ13*2t 2

15 722119A Fixed Plate 1

16 WF061620 Washer M6*φ16*2t 2

17 SR0894403 Cap Screw M8*1.25*16 2

18 722620 Plate 1

19 WS080000 SPRING Washer M8 2

20 NH081304 Hex Nut M8 2

21 WF051010 Washer M5*φ10*1t 4

22 SM049200 Pan Head Screws Hexagon M4*8 2

23 722122 Cutter 1

24 WS060000 SPRING Washer M6 2

25 SH069400 Hex Head Bolt M6*1*16 1

26 SR0502403 Cap Screw M5*0.8*10 2


QCE34006
QCE34006
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721255 SPREAD GLUE SHAFT 1
2 721246 Ring 1
3 721247 Disc Washers φ46.5*φ3.0*0.6t 6
4 721248 Ring 1
5 WF253510 Washer M25xφ35xt1 7
6 722134 SPREAD GLUE BASE 1
7 BB600500A Ball Bearing 6005ZZ 1
8 721250 Ring 1
9 RR470000 C-Type Retaining Ring R47 2
10 BB600502A Ball Bearing 6005ZZ 1
11 203198 oil mouth 1/16" 1
12 NH061000 Hex Nut M6 1
13 721251 STEP BOLT 2
14 SS069100 Set Screw M6*1*6 1
15 721256 PREVENT DUST OUTSIDE RING 1
16 721257 PREVENT DUST INSIDE RING 1
17 721252 LOCKING NUT(& STAR WASHER) 1
18 722146 Sprocket 05B-12T 1
QCE34007
QCE34007

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 721276 KNOB SCREW M6x75L 1

2 NH061000 Hex Nut M6 7

3 206395 Spring φ15*φ6.2*0.5t 2

4 SH080600 HEX HEAD BOLT M8*1.25*30 1

5 WS080000 SPRING WASHER M8 1

6 SR0594403 Cap Screw M5x16L 1

7 WS050000 SPRING WASHER M5 1

8 WF051210 FLAT WASHER φ5xφ12x1t 2

9 WF061920 FLAT WASHER M6xφ19 1

10 SS069200 Set screw M6*1*8 2

11 721273 Block 1

12 721261 Block 1

13 721274 plank 1

14 WF062020 FLAT WASHER M6xφ20xt2 2

15 721272 Shaft 1

16 WW152203 WASHER φ15xφ22 3

17 721262 cushion 1

18 721275 Heater 1

19 SR060400 Cap Screw M6*1*20 6

20 WS060000 SPRING WASHER M6 7

21 721264 Block 1

22 721265 ADJUST ROTATE TUBE 1

23 SH069400 HEX HEAD BOLT M6*1*16 1

24 WF061820 FLAT WASHER M6xφ18 1

26 721270 slice 1

27 SJ049100 Button Head Screw M4*0.7*6 4

28 721268 COVER PLATE 1

29 721269 COVER PLATE 1

30 SR049100 Cap Screw M4*0.7*6 2

31 721263 SUPPORT PLATE 1

32 SR069400 Cap Screw M6*1*16 2

33 WF061310 FLAT WASHER M6*φ13 3

34 721267 ADJUST BSAE 1

35 721266 COVER PLATE 1

36 721056 KNOB 2

37 NH081300 Hex Nut M8 2

38 721278A COVER PLATE 1

39 SR081100 Cap Screw M8*1.25*55 1

40 722138 COVER PLATE 1

41 WF061320 FLAT WASHER M6*φ13 2

42 722137 GLUE BARREL UPPER COVER 1


QCE34008

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722135 Coines 1

2 SM060400 Countersunk Head Cap Screw M6*20 2

3 WF061820 Washer M6xφ18 1

4 WS060000 Spring Washer M6 11

5 SR060400 Cap Screw M6*1*20 1

6 722136 Non-Asbestos Gasket 1

8 721288 Temperature Line 2M 1 E340

721288A Temperature Line 3M 1 S,E350

9 SR061000 Cap Screw M6*1*50 4

10 722141 Heater 200W 2

11 SS069100 Set screw M6*1*6 4

12 722140 Heater 300W 2

13 SP059210 Pan Head Screw M5*8L 2

14 721280 Ceramic Terminal Block 1

15 721287 Switch Box 1

16 709412 Outlee Beads PG11 2

17 IC722015 Power Cord 2.0mm2*2C*60cm*4 1

18 722152 Cover 1 FC

19 WF061620 Washer M6xφ16 2

20 SR069300 Cap Screw M6*1*12 2


QCE34009
QCE34009

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 NL081300 Nylon Nut M8*1.25 1

2 721306 gyrate button 1

3 WF082320 Washer M8*φ23 1

4 722145 Fixed Flakes 1

5 722144 Screw M8*140L 1

6 721305 Flakes 2

7 721304 Spring φ16*75L 1

8 NH081300 Hex Nut M8 6

9 721301 Y-Type Connector Y20 1

10 WS080000 Spring Washer M8 1

11 MA722142 Motor 380V 3~ 50HZ 1

MA722142A Motor 220V 3~ 60HZ 1 S(CSA)

MA722142B Motor 220V 1~ 50HZ 1 S

12 WF081818 Washer M8*φ18*t1.8 1

13 200964 tube 1

14 721300 Type Connector 1

15 SS081000 Set Screw M8*1.25*50 1

16 IM722005 Motor Cord 0.5mm2*4C 1 (CE, 380~415V)

IM722025 Motor Cord 20AWG*4C 1 S,(CSA, 220~240V)

IM722035 Motor Cord 0.75mm2*3C 1 S,(CE, 220~240V)

17 SR0614003 Cap Screw M6*1*70 2

18 721310 Reducer 減速比1/20 1 50HZ用

721310A Reducer 減速比1/25 1 S.60HZ用

19 KD050518 key 5*5*18 3

20 722147 Shaft 1

21 SH081640 Hex Head Bolt M8*1.25*80 1

22 RS140000 C-Type Retaining Ring S14 1

23 722132 Adjustment Blocks 1

24 NH061000 Hex Nut M6 2

25 WS060000 Spring Washer M6 5

26 SH061040 Hex Head Bolt M6*1*50 3

27 RS300000 C-Type Retaining Ring S30 1

28 722133 Ring 1

29 BB600602A Ball Bearing 6006ZZ 2

30 722148 Adjustment Bracket 1

31 BB690102 Ball Bearing 6901ZZ 2

32 722149 Sprocket 05B-20T 1

33 SS069100 Set Screw M6*1*6 1

34 RS120000 C-Type Retaining Ring S12 1

35 SR080700 Cap Screw M8*35L 2

36 722151 1
QCE34009

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

37 BB608002A Ball Bearing 608ZZ 2

38 722150 Chain 05B-48目 1

39 WF082030 Washer M8*φ20*3T 5

40 WS080001 Spring Washer M8 7

41 SS080407 Set Screw M8*1.25*20 4

42 SH080600 Cap Screw M8*1.25*30 4

43 WF081210 Washer M8*φ12*1.0T 4

44 WF083020 Washer M8*φ30*2T 2

45 SH0804403 Hex Head Bolt M8*20L 1


QCE34010
QCE34010

ITEM PART NO PARTS NAME SIZE Q`TY NOTE


1 722156 slice 1
2 SR082000 Cap Screw M8*1.25*100 2
3 722160 gyrate button 2
4 WF082320 Washer M8*φ23 4
5 SS089200 Set screw M8*1.25*8 4
6 SS069400 Set screw M6*1*16 4
7 WF081818 Washer M8*φ18*t1.8 2
8 SH080600 Hex Head Bolt M8*1.25*30 2
9 722166 Spring 2
10 NL081300 Lock Nut M8*1.25 2
11 NH081300 Hex Nut M8 2
12 722165 Shaft 1
13 BB600403A Bearing 6004LLU 2
14 RR420000 Retaining Ring (for bores) R42 2
15 722162 Roll Wheel 1
16 RS200000 Retaining Ring (for bores) S20 1
17 SS060200 Set screw M6*10 4
18 722157 Block 1
19 WF061620 Washer M6*φ16 2
20 SH060400 Hex Head Bolt M6*1*20 2
21 722158 Adjustment Bracket 2
22 BL210402 Bearing LM12UU 8
23 SJ049100 Button Head Screw M4*0.7*6 8
24 722159 Shaft φ12 4
25 RS150000 Retaining Ring (for bores) S15 1
26 722163 Roll Wheel 1
27 BD152001 Bearing DU15x20 2
28 722164 Shaft 1
QCE34011
QCE34011

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 SS080400 Set screw M8*1.25*20 2

2 722431 Adjustment Bracket 1

3 NH081300 Hex Nut M8 8

4 SS080500 Set screw M8*1.25*25 2

5 722427 join Block 1

6 WF081615 Washer M8*φ16*t1.5 1

7 721205 Washer φ16*φ8.2*0.4t 1

8 NL081300 Lock Nut M8*1.25 2

9 722424 buffer slice 14

10 722430 shaft 2

15 SH0806403 Hex Head Bolt M8*1.25*30 3

16 WF082030 Washer M8*φ20*3mm 3

17 722411 fixed plank 1

19 721205 Spring φ16*φ8.2*0.4t 1

20 SH0804403 Hex Head Bolt M8*20L 4

21 WS080001 Spring Washer (EXT.) M8 13

22 WF081818 Washer M8*φ18*t1.8 5

23 722433 join Block 1

24 721200 buffer Block 2

26 722186 Adjustment Bracket 1

27 722423A fixed slice 1

28 SJ080600 Button Head Screw M8*1.25*30 1

30 722655 Buffers 1

32 SR060400 Cap Screw M6*1*20 4

33 WF061315 Washer M6*φ13 4

34 SR069400 Cap Screw M6*1*16 2

35 SR060500 Cap Screw M6*1*25 7

36 722185 line track 1

37 AB722432A Barometric pressure cylinder 1 A

39 WF082320 Washer M8*φ23 3

41 WE160000 Washer M16 1

44 AB722640 Barometric pressure cylinder 1 A

45 WF062330 Washer M6*φ22*3t

46 WS060000 Spring Washer M6 2

48 722052 Spacer Ring 2

49 SJ080500 Button Head Screw M8*1.25*25 1


QCE34012
QCE34012

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722435 high speed Motor 1

1-1 722435-5 Hex Nut 1

1-2 722435-4 Flange 1

1-3 722435-3 ring 1

1-4 722435-2 Flange 1

1-5 722435-1 high speed Motor 1

1-6 722435-6 connect 1

2 721227A plank 1

3 BB692002 Ball Bearing 692ZZ 4

4 722413 Scoring Saw Blade 2

5 722642 pin 2

6 NL081300 Lock Nut M8 1

7 SR050200 Cap Screw M5*0.8*10 3

8 AB722429 Barometric pressure cylinder 1

9 WE220000 Washer M22 2

10 722428 slippery Block 1

11 BL210402 line Bearing LM12UU 8

12 WS060000 Spring Washer M6 4

13 SR060700 Cap Screw M6*1*35 4

14 SM059400 shallow Cap Screw M5x16 4

15 721227B plank 1

16 SM049200 shallow Cap Screw M4*8 6

17 722422 Block 1

18 NH081300 Hex Nut M8 1

19 BB608002A Ball Bearing 1

20 SH08110403 Hex Head Bolt M8*1.25*55 1

21 722419 frame 1

22 WF081818 Washer M8*φ18*t1.8 2

23 WS080001 Spring Washer (EXT.) M8 3

24 SH0806403 Hex Head Bolt M8*1.25*30 2

25 721232 Washer φ12*φ5*0.6t*1.5t 24

30 722426 fixed plank 1

31 SM089400 shallow Cap Screw M8x16 2

32 722417 centralize cover 1

33 WF051620 Washer M5*φ16*2T 3

34 709411 Outlet Beads PG-11 1

35 WS050000 Spring Washer M5 3

36 722438 Plate 1

37 WS060000 Spring Washer M6 2

38 SR060800 Cap Screw M6*1*40 2

39 PP061600 Pin φ6*16L 2


QCE34012

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

40 SS0399003 Set Screw M3*3 2

41 WF051320 Washer M5*φ13*2T 2

42 WS050000 Spring Washer M5 2

43 SR059400 Cap Screw M5*0.8*16 2

44 722653 Reed tabs 2

45 IC722028 Reed Switch 1 (E340)

IC722520 Reed Switch 1 (E350)

46 IC722029 Reed Switch 1 (E340)

IC722028 Reed Switch 1 (E350)

47 IM722001 CONNECT CORD


2 1 (CE)
0.5mm *4C

IM722021 CONNECT CORD 20AWG**4C 1 S,(CSA)


QCE34013
QCE34013

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 NL061000 Lock Nut M6 4

2 722253 gyrate button 1

3 722455 casing 1

4 721201 join Bearing PHS-06 1

5 SR060500 Cap Screw M6*1*25 2

6 SS061600 Set screw M6*1*80 1

7 WF061620 Washer M6*φ16 *2T 5

8 722254 Spring 1

9 WF162512 Washer M16*φ25*1.2t 1

10 722215 lean against plank 1

11 722457 Adjustment Bracket 1

12 SS050200 Set screw M5*0.8*10 4

13 SM080400 Hex Countersunk Screw M8x20 2

14 722263 Adjust Screw 2

15 206395 tray Spring φ15*φ6.2*0.5t 6

16 722261 tube 2

17 722262 Digital position indicator 1

18 NH061000 Hex Nut M6 8

19 722258 blossom Nut M6 2

20 722268 Shaft 1

21 722267 Spring 1

22 NH081300 Hex Nut M8 2

23 722266 adjust Nut 1

24 SS081600 Set screw M8*1.25*80 1

25 NL081300 Lock Nut M8*1.25 1

26 SR060400 Cap Screw M6*1*20 2

27 722467 Set screw M6*16L 2

28 SS060700 Set screw M6*1*35 2

29 WF082030 Washer M8*φ20*3t 4

30 WF062020 Washer M6*φ20*2t 2

31 722454 plank 1

32 WS080001 Spring Washer (EXT.) M8 5

33 722274 scrape slice 1

34 WF101610 Washer M10*φ16*1.0 1

35 SR069400 Cap Screw M6*1*16 4

36 722264 Block 1

37 722448 Block 1

38 722450 Adjustment Bracket 1

39 SR060600 Cap Screw M6*1*30 1

40 722468 Set screw M8*32t 1

41 SG069200 Hex Flange screw M6*1*8 2

42 722451 collecting 1
QCE34013
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
43 SM0694403Countersunk Head Cap Screw M6x16 3
44 SR049200 Cap Screw M4*0.7*8 1
45 WF041010 Washer M4*φ10 1
46 722462 scrape slice 1
47 SR080600 Cap Screw M8*1.25*30 4
48 722463 Adjustment Bracket 1
49 SM049200Countersunk Head Cap Screw M4*8 6
50 722052 ring 2
51 BB600004 Ball Bearing 6000LLB 1
52 722218 Shaft 1
53 721069 imitate wheel 1
54 722271 casing 2
55 722442 Adjustment Bracket 1
56 722441 Adjustment Bracket 1
57 NH081304 Hex Nut M8*1.25*4t 1
58 SS080407 Set screw M8*1.25*20 4
59 722453 PLATE 1
60 SR059200 Cap Screw M5*0.8*8 2
61 WS050000 Spring Washer M5 2
62 722646 Cover 1
QCE34014

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722445 slice 1

2 722447 Adjustment Bracket 1

3 SR0699003 Cap Screw M6*1*14 6

4 WF082320 Washer M8*φ23 1

5 SH080700 Hex Head Bolt M8*1.25*35 1

6 SS060800 Set screw M6*1*40 1

7 NL061000 Lock Nut M6 2

8 722446 fixed position screw 3

9 NH061000 Hex Nut M6 4

11 SR059200 Cap Screw M5*0.8*8 1

12 722443 Adjustment Bracket 1

13 KD060640 Key 6*6*40 2

14 722466 high speed Motor 1

15 IM722003 MOTOR CORD 0.5mm2*4C 1 (CE)

IM722023 MOTOR CORD 20AWGx4C 1 S,(CSA)

16 722235 Flange 1

17 SM0694403 Countersunk Head Cap Screw M6x16 1

19 AB722239 substitute cutting tools R2 1

AB722239A substitute cutting tools R3 1 S

20 WS080001 Spring Washer (EXT.) M8 1

21 NA061000 Acorn Nut M6 2


QCE34015
QCE34015

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722258 blossom Nut M6 2

2 721068 scrape slice 1

3 WF101610 Washer M10*φ16*1t 1

4 WF082030 Washer M8*φ20*3t 2

5 SR069400 Cap Screw M6*1*16 4

6 722448 Block 1

7 722450 Adjustment Bracket 1

8 SH060400 Hex Head Bolt M6*1*20 2

9 WF061620 Washer M6*φ16*2t 2

10 722465 collecting 1

11 722264 Block 1

12 722442 Adjustment Bracket 1

13 722468 Set screw M6*32t 1

14 NH081300 Hex Nut M8 2

15 SR060600 Cap Screw M6*1*30 1

16 NH061000 Hex Nut M6 8

17 SR060400 Cap Screw M6*1*20 2

18 722262 Digital position indicator 1

19 722261 tube 2

20 SS060700 Set screw M6*1*35 2

21 WF062020 Washer M6*φ20*2t 2

22 206395 Spring φ15*φ6.2*0.5t 6

23 722263 adjust Screw 2

24 SM080400 Hex Countersunk Screw M8x20 2

25 SS050200 Set screw M5*0.8*10 4

26 722457 Adjustment Bracket 1

27 722215 lean against plank 1

28 722274 scrape slice 1

29 SM049200 Hex Countersunk Screw M4*8 6

30 721201 join Bearing PHS-06 1

31 WF162512 Washer M16*φ25*1.2t 1

32 722254 Spring 1

33 722455 casing 1

34 WF061620 Washer M6*φ16 5

35 NL061000 Lock Nut M6 4

36 722253 gyrate button 1

37 SS061600 Set screw M6*1*80 1

38 SR060500 Cap Screw M6*1*25 2

39 722467 Set screw M6*16L 2

40 722454 plank 1

41 722052 ring 2

42 NH081304 Hex Nut M8*1.25*4t 1


QCE34015
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
43 722282 Adjustment Bracket 1
44 722268 Shaft 1
45 722267 Spring 1
46 722266 adjust Nut 1
47 SS081300 Set screw M8*1.25*65 1
48 NL081300 Lock Nut M8*1.25 1
49 722271 casing 2
50 SM0694403 Hex Countersunk Screw M6x16 3
51 722463 Adjustment Bracket 1
52 SH0806403 Hex Head Bolt M8*1.25*30 2
53 BB600004 Ball Bearing 6000LLB 1
54 722218 Shaft 1
55 721069 imitate wheel 1
56 WS080001 Spring Washer (EXT.) M8 3
57 SR049200 Cap Screw M4*0.7*8 1
58 WF041010 Washer M4*φ10 1
59 721073 Brush 0.02 40mm
QCE34016

ITEM PART NO PARTS NAME SIZE Q`TY NOTE


1 722445 slice 1
2 722447 Adjustment Bracket 1
3 SR0699003 Cap Screw M6*1*14 6
4 WF082320 Washer M8*φ23 1
5 SH080700 Hex Head Bolt M8*1.25*35 1
6 SS060800 Set screw M6*1*40 1
7 NL061000 Lock Nut M6 2
8 722446 fixed position screw 3
9 NH061000 Hex Nut M6 4
11 SR059200 Cap Screw M5*0.8*8 1
12 722443 Adjustment Bracket 1
13 KD060640 Key 6*6*40 2
14 722466 high speed Motor 1
15 IM722004 MOTOR CORD 0.5mm2*4C 1 (CE)
IM722024 MOTOR CORD 20AWGx4C 1 S(CSA)
16 722235 Flange 1
17 SM0694403 Countersunk Head Cap Screw M6x16 1
19 AB722238 substitute cutting tools R2 1
AB722238A substitute cutting tools R3 1 S
20 WS080001 Spring Washer (EXT.) M8 1
21 NA061000 Acorn Nut M6 2
QCE34017
QCE34017

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722269 lean against plank 1

2 722270 Adjustment Bracket 1

3 SS049200 Set screw M4*0.7*8 4

4 SR060200 Cap Screw M6*1*10 2

5 722265 Block 1

6 SS060800 Set screw M6*1*40 2

7 722263 adjust Screw 1

8 206395 Spring φ15*φ6.2*0.5t 5

9 722264 Block 1

10 SR069400 Cap Screw M6*1*16 2

11 NH061000 Hex Nut M6 8

12 722261 tube 1

13 722260 Adjustment Bracket 1

14 NL081300 Lock Nut M8*1.25 3

15 721205 Washer φ16*φ8.2*0.4t 4

16 722262 Digital position indicator 1

17 722258 Hex Nut M6 1

18 NH081300 Hex Nut M8 4

19 SS081500 Set screw M8*1.25*75 1

20 722267 Spring 1

21 722266 adjust Hex Nut 1

22 NH081304 Hex Nut M8*1.25*4t 2

23 722271 casing 2

24 722259 Screw M6 2

25 WF082030 Washer M8*φ20*3t 2

26 NL061000 Lock Nut M6 5

27 722268 Shaft 1

28 722279 scrape slice 1

29 SR039200 Cap Screw M3*0.5*8 1

30 722276 adjust Shaft 1

31 WF101610 Washer M6*φ16*1T 2

32 SS080900 Set screw M8*1.25*45 2

33 722468 Set screw M6*32t 3

34 722273 gyrate button 1

35 SR060500 Cap Screw M6*1*25 1

36 SM049200 Hex Countersunk Screw M4*8 4

37 SR049200 Cap Screw M4*0.7*8 1

38 WF040810 Washer M4*φ8 1

39 722278 scrape slice R2 1

722278A scrape slice R3 1 S

40 722280 Adjustment Bracket 1


QCE34017

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

41 WF061620 Washer M6*φ16 1

42 722253 gyrate button 2

43 SS049200 Set screw M4*0.7*8 1

44 SS060700 Set screw M6*1*35 1

45 722256 tube 1

46 722252 Adjustment Bracket 1

47 SM059300 Hex Countersunk Screw M5*0.8*12 2

48 721201 join Bearing PHS-06 1

49 722254 Spring 1

50 SS039200 Set screw M3*0.5*8 1

51 722251 Adjustment Bracket 1

52 SS060200 Set screw M6*10 1

53 SH060440 Hex Head Bolt M6*1*20 2 鋼質

54 WF061310 Washer M6*φ13 2

55 SM060400 shallow Cap Screw M6*20 1

56 722281 plank 1

57 722272 Attachment 1

58 722274 scrape slice 1

59 SS080407 Set screw M8*1.25*20 4

60 SR080600 Cap Screw M8*1.25*30 4

61 WS080001 Spring Washer (EXT.) M8 4

62 WF082030 Washer M8*φ20*3t 4

63 721071 Lock Nut M10*P0.75 1

64 WF162512 Washer M16*φ25*1.2t 1

66 WF030810 Washer M3*φ8*1.0t 1


QCE34018
QCE34018

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 NL061000 Lock Nut M6 5

2 722253 gyrate button 2

3 SS039200 Set screw M3*0.5*8 1

4 722254 Spring 1

5 WF061620 Washer M6*φ16 2

6 SM059300 shallow Cap Screw M5*0.8*12 2

7 721201 join Bearing PHS-06 1

8 722284 lean against plank 1

9 SH060440 Hex Head Bolt M6*1*20 2

10 WF061310 Washer M6*φ13 2

11 SS050200 Set screw M5*10 1

12 722272 Attachment EPL4-M5 1

13 722282 Adjustment Bracket 1

14 SS060700 Set screw M6*1*35 1

15 NH061000 Hex Nut M6 7

16 SR060500 Cap Screw M6*1*25 1

17 722468 Set screw M6*32L 3

18 722265 Block 1

19 SR039200 Cap Screw M3*0.5*8 1

20 722279 scrape slice 1

21 722278 scrape slice R2 1

722278A scrape slice R3 1 S

22 WF040810 Washer M4*φ8 1

23 SR049200 Cap Screw M4*0.7*8 1

24 722280 Adjustment Bracket 1

25 722276 adjust Shaft 1

26 WF101610 Washer M6*φ16*1T 2

27 SS049100 Set screw M4*0.7*6 1

28 722273 gyrate button 1

29 722263 adjust Screw 1

30 206395 Spring φ15*φ6.2*0.5t 5

31 722264 Block 1

32 SR069400 Cap Screw M6*1*16 2

33 722261 tube 1

34 722262 Digital position indicator 1

35 722258 Hex Nut M6 1

36 722271 casing 2

37 722268 Shaft 1

38 NH081300 Hex Nut M8 4

39 SS081500 Set screw M8*1.25*75 1

40 722267 Spring 1
QCE34018

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

41 722266 adjust Hex Nut 1

42 NH081304 Hex Nut M8*1.25*4t 2

43 722259 Screw M6 2

44 721071 Hex Nut GUK10xP0.75 1

45 SR060200 Cap Screw M6*1*10 2

46 SS049200 Set screw M4*0.7*8 4

47 SS080900 Set screw M8*1.25*45 2

48 722283 Adjustment Bracket 1

49 SM060400 Hex Countersunk Screw M6*20 1

50 722285 plank 1

51 722270 Adjustment Bracket 1

52 722274 scrape slice 1

53 SM049200 Hex Countersunk Screw M4*8 4

54 722252 plank 1

55 722256 tube 1

56 WF082030 Washer M8*φ20*3t 2

57 721205 Washer φ16*φ8.2*0.4t 4

58 NL081300 Lock Nut M8*1.25 3

59 WF061620 Washer M6*φ16 2

60 SS060700 Set screw M6*1*35 2

61 SH0806403 Hex Head Bolt M8*1.25*30 2

62 WS080001 Spring Washer (EXT.) M8 2

63 WF082030 Washer M8*φ20*3t 2

64 722286 Attachment EPE-4 1

65 WF162512 Washer M16*φ25*1.2t 1

67 WF030810 Washer M3*φ8*1.0t 1


QCE34019
QCE34019

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 MA721321 Motor 1/6HP 50HZ 1 (CE, 380~415V)

MA721321C Motor 1/6HP 60HZ 1 S,(CSA, 220~240V)

MA721321A Motor 1/4HP(0.18KW) 2P(順) 1 S,(CE, 220~240V)

2 721319 Motor Fixed Plate 2

3 722291 Fixed Plate 1

4 721324 Fixed Plate M8 2

5 721316 Flange Flakes 2

6 WS080000 Spring Washer M8 6

7 SH080402 Hex Head Bolt M8*20L(左牙) 1

8 WS050000 Spring Washer M5 8

9 SR059400 Cap Screw M5*16L 8

10 SR069300 Cap Screw M6*12L 4

11 721318 Wheel Spindle 左牙 1

12 721317 Wheel 5" 2

13 SH080400 Hex Head Bolt M8*20L 1

14 IM722006 Motor Cord 0.5mm2*4C 1 (CE, 380~415V)

IM722026 Motor Cord 20AWGx4C 1 S,(CSA, 220~240V)

IM722036 Motor Cord 0.75mm2*3C 1 S,(CE, 220~240V)

15 WF082030 Washer M8*φ20*3mm 4

16 721322 Wheel Spindle 1

17 SH080500 Hex Head Bolt M8*25L 4

18 IM722007 Motor Cord 0.5mm2*4C 1 (CE, 380~415V)

IM722027 Motor Cord 20AWGx4C 1 S,(CSA, 220~240V)

IM722037 Motor Cord 0.75mm2*3C 1 S,(CE, 220~240V)

19 SR080400 Cap Screw M8*1.25*20 4

20 WS080000 Spring Washer M8 4

21 721320 Washer φ22*φ55*3t 2

22 MA721321 Motor 380V 3~ 50HZ 1 (CE, 380~415V)

MA721321C Motor 1/6HP 60HZ 1 S,(CSA, 220~240V)

MA721321B Motor 1/4HP(0.18KW) 2P(逆) 1 S,(CE, 220~240V)


QCE35020 -Optional

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722311 Fixed 1

2 WF061620 Washer M6*φ16*t2.0 6

3 SH0611403 Hex Head Bolt M6*55L 6


QCE35020 -Optional
ITEM PART NO PARTS NAME SIZE Q`TY NOTE

4 722318 Mobile Block 2

5 SJ049100 Rouad Socket Head Cap Screw M4*6L 8

6 BL210402 line Bearing LM12UU 8

7 WS060000 Spring Washer M6 12

8 SR061100 Cap Screw M6*55L 4

9 NL081300 Nylon Nut M8 4

10 721306 Plum Nut 4

11 WF082030 Washer M8*φ20*t3.0 2

12 722144 Screw Polt 2

13 721088 Spring 2

14 721305 Gasket 2

15 NH081304 Hex Nut M8 2

16 722323 Scraping Block 2

17 SS060200 Set Screw M6*10L 12

18 722324 Fixed Plate 2

19 SH069400 Hex Head Bolt M6*16L 4

20 204263 Washer φ20*φ10*1t*1.5t 2

21 722325 Adjusting Bolt 2

22 721071 Locknut 2

23 722321 Chrome Rod Park 4

24 SH059200 Hex Head Bolt M5*8L 2

25 WF051210 Washer M5*φ12*t1.0 2

26 722314 Scraper 1

27 SR069400 Cap Screw M6*16L 2

28 722329 Countersunk Head Cap Screw 2

29 722315 Scraping Blade 2

30 722316 Blade Fixed 1

31 WF082020 Washer M8*φ20*t2.0 2

32 SM040200 Pan Head Screws Hexagon M4*10 4

33 BB620004A Ball Bearing 6200LLU 2

34 722312 Profiling Roller 2

35 WF101610 Washer M10*φ16*t1.0 2

36 722313 Fixed Bolt 2

37 722327 Fixed Plate 1

38 SR060400 Cap Screw M8*20L 4

39 722328 Scraper 1

40 722326 Blade Fixed 1


QCE35021
QCE35021

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 AB722577 Control Box ASM. 1 R

2 722578 Bracket 1 VE

3 998808 Nylon Box Connector 2

4 SJ050200Rouad Socket Head Cap Screw M5*0.8*10 5

5 BR000043 Pop Rivet 4-3 ∮3.2 x 8.9 29

6 998807 fixed seat 2

7 722412 fixed Plate 4

8 722386 Cover 2 R

9 994865 Power Switch 3~220~240/380~415V (Ith=40A)用 1

10 201105 Switch Box 1

11 136013 Outlet Beads PG-13.5 11 R

13 722567 Stand 1 R

14 AB722568A Distribution Botton Plate 230V 3~ 60HZ (TE+) 1 S,CSA

AB722568B Distribution Botton Plate 230V 3~ 60HZ (TE+) 1 S,

AB722568N Distribution Botton Plate 380V 3~ 50HZ 1 S,50HZ

15 SR120600 Cap Screw M12*1.75*30 8

16 WS120000 Spring Washer M12 8

17 WF122720 Washer M12*φ27*2.0 8

18 AB721037-D Door Safety Switch ASM. 1

19 SP040710 Pan Head Screw M4*0.7*35 7

20 NH061000 Hex Nut M6 5

21 WF061820 Washer M6xφ18 16

22 SR060400 Cap Screw M6*1*20 5

23 AB722591 Pressure Adjustment Group 1

24 AB721364 pressure switch organize 1 CE

AB721364A pressure switch organize CUL 1 S,CSA

25 AB722478 Solenoid Valve AC24V 1

AB722478A Solenoid Valve AC24V/ S,CSA

26 NL101700 Nylon Nut M10*1.5 4

27 SP049200 Pan Head Screw M4*0.7*8 2

28 SR100800 Cap Screw M10*1.5*40 4

29 721111 Class Screw 3

30 721110 Roller 3

31 722579 Plate 1

32 722572 Cover 1 R

33 722375B Plate 1 T

34 SR069300 Cap Screw M6*1*12 13

35 722571 Back Cover 1 R

36 722569 Back Cover 1 R


QCE35021

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

37 722570 Back Cover 1 R

38 721342 Mechanical Locks CD-406-E 2

39 AB721367 Three-Point Combination Group 1

AB721367A Three-Point Combination Group 1 S

40 722385 Transparent Cover 2

41 SR080400 Cap Screw M8*1.25*20 2

42 WF082020 Washer M8xφ20 2

43 722374 Fixed Plate 2

44 722580 Fixed Plate 1

45 SR059300 Cap Screw M5*12 24

46 136826 Lock LY-4050 6

47 SJ060200 Button Head Screw M6*1*10 6

48 NF040700 Flange Nut M4*0.7 4

49 709409 Outlet Beads PG-9 23

50 722583 outer garment 1 R

51 722104 Shaft 2

52 NH081300 Hex Nut M8 2

53 WF061620 Washer M6*φ16*2T 16

54 AB721037-E Door Safety Switch ASM. 1

55 AB136631A Emergency Stop Button 1

56 WF081818 Washer M8*φ18*t1.8 22

57 NL081300 Nylon Nut M8*1.25 12

58 722380 nitrogen gas vat 40KG 2

59 SJ080600 Button Head Screw M8*1.25*30 4

60 722381 Extension Bracket 4

61 721345 Hose φ2.5"*25 1

62 L150000000000000 terminate line 15CM 10

63 721347 Hose φ2.5"*80 2

64 722575 Distribution Box door 1 VE

65 WF102120 Washer M10xφ21xt2 4

66 205557 Handle MS-737-1-A-330 2

67 SR060200 Cap Screw M6*1*10 12

68 204197 Wave Tube NGN-28B 1 (1000mm)

69 722585 Plate 1

70 SH089400 Hex Head Bolt M8x16L 5

71 721336 Grounded Steel Plate 1

72 721409 Fixed Plate 6

73 WS080000 Spring Washer M8 10

74 WS060000 Spring Washer M6 13

75 207750 Plug HP-30 6


QCE35003

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 SR060200 Cap Screw M6*1*10 8

2 WS060000 Spring Washer M6 4

3 722521 Collecting 1
QCE35003
ITEM PART NO PARTS NAME SIZE Q`TY NOTE

4 722501 High speed Motor 2

5 721231 Brush 2240mm/ 0.1 110L*2

6 722526 Precise Nut M25*1.5P 2

7 722502 Cutting tool 2

8 722504 Adjustment Bracket 1

9 SM089400 Shallow Cap Screw M8x16 2

10 PP081200 Pin φ8*12 4

11 SM069300 Shallow Cap Screw M6x12 12

12 722505 Shafe 2

13 722522 Collecting 1

14 722507 Adjustment Bracket 1

15 IM722510 Motor Cord 0.5mm²x4C 1 (CE)

16 IM722511 Motor Cord 0.5mm²x4C 1 (CE)

17 722525 Fixed Plate 2

18 721231 Brush 2240mm/ 0.08 90L*2支


QCE35004

ITEM PART NO PARTS NAME SIZE Q`TY NOTE


1 NH081300 Hex Nut M8 6
2 721205 Disc Washer φ16*φ8.2*0.4t 10
3 WF081818 Washer M8*φ18*t1.8 6
4 SS080600 Set screw M8*1.25*30 4
QCE35004

ITEM PART NO PARTS NAME SIZE Q`TY NOTE


5 SM049200 Countersunk Head Cap Screw M4*8 8
6 BL210402 Bearing LM12UU 8
7 722506 Adjustment Bracket 2
8 SS069100 Set screw M6*1*6 20
9 SM080600 Countersunk Head Cap Screw M8x30 2
11 SR080500 Cap Screw M8*1.25*25 3
12 WS080000 Spring Washer M8 3
13 SJ059200 Button Head Screw M5*0.8*8 8
14 722509 Adjustment Bracket 1
15 722508 Adjustment Bracket 1
16 SM089400 Countersunk Head Cap Screw M8x16 2
17 722523 Block 1
18 203163 Precise Nut 1
19 722518 Shaft 2
20 SM059200 Countersunk Head Cap Screw M5*0.8*8 4
21 BL320602 Bearing LM20UU 4
22 722519 Adjust Screw 1
23 BD151501 DU Bushing DU15x15 1
24 SR100600 Cap Screw M10*1.5*30 6
25 WS100000 Spring Washer M10 4
26 722515 Cover 1
27 BD151501 DU Bushing DU15x15 2
29 NH061000 Hex Nut M6 4
30 SR060800 Cap Screw M6*1*40 4
32 722512 Shaft 4
33 722513 Block 2
34 SR080500 Cap Screw M8*1.25*25 4
35 NH101700 Hex Nut M10x1.5 2
36 SS100907 Set screw M10*1.5*45 2
37 722517 BASE 1
38 722514 Shaft 4
39 AB722511 Cylinders(ASM.) 2
40 SR061000 Cap Screw M6*1*50 4
41 SR100500 Cap Screw M10*1.5*25 2
42 NH081304 Hex Nut M8*1.25*4t 2
43 WF082030 Washer M8*φ20*3mm 2
44 SR080600 Cap Screw M8*1.25*30 2
45 722516 Support 1
46 722510 Side panel 1
47 SM080500 Countersunk Head Cap Screw M8x25 3
QCE35005
QCE35005
ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722353 Plate 1

2 722534 Slice 1

3 SR0602003 Cap Screw M6*1*10 2

4 NH061000 Hex Nut M6 5

5 722446 Fixed position screw 3

6 722531 BASE 1

7 722532 Adjustment Bracket 1

8 722537 Tray Spring M10*20*0.8t 5

9 722538 Adjustment Plate 1

10 SS050400 Set screw M5*0.8*20 2

11 722536 Adjust Screw 1

12 017071 Bearing 1

13 722535 Block 1

14 SR0694003 Cap Screw M6*1*16 2

15 NH101700 Hex Nut M10x1.5 2

16 722533 Tube 1

17 722539 Digital position indicator 1

18 722530 Quick Release Handle 1

19 SR100600 Cap Screw M10*1.5*30 3

20 WS100000 Spring Washer M10 3

21 SS080207 Set screw M8*1.25*10L 4

22 SR080500 Cap Screw M8*1.25*25 2

23 BD101001 DU Bushing φ10*10L 1

24 SS060400 Set screw M6*1.0*20 2


QCE35006
QCE35006
ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 SR069400 Cap Screw M6*1*16 4

2 722544 Block 1

3 SM049200 Hex Countersunk Screw M4*8 4

4 BL210402 Bearing LM12UU 4

5 722541 Plate 1

6 722548 Heater 300W 220V 1

7 SS069200 Set screw M6*1*8 4

8 SS080207 Set screw M8*1.25*10 4

9 WS080000 Spring Washer M8 7

10 SR080500 Cap Screw M8*1.25*25 7

11 722159 Shaft 2

12 722543 Adjustment Bracket 1

13 722545 Frame 1

14 200964 Bushing 6

15 NH061000 Hex Nut M6 1

16 SS069400 Set screw M6*1*16 1

17 SM080500 Hex Countersunk Screw M8x25 3

18 722542 Fixed plate 1

19 SR081800 Cap Screw M8*1.25*90 1

20 SJ069300 Button Head Screw 2

21 722547 Cover 1

22 NH081300 Hex Nut M8 1

23 NL081300 Nylon Hex Nut M8*1.25 1

24 722166 Spring 1

25 WF082320 Washer M8*φ23 2

26 722546 Block 1

27 722160 Gyrate button 1

28 SR081800 Cap Screw M8*1.25*90 1


QCE35007

ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 722500 Cover 1

2 203163 Nut 1

3 994216 Bearing 51104 2

4 722498 Disc 1

5 SJ069300 Button Head Screw M6x12L 8

6 WF101610 Washer M10*φ16*1T 8

7 BB600002A Bearing 8

8 722218 Shaft 8

9 SR089400 Cap Screw M8*16L 5

10 722499 Shaft 1

11 722481 Edge With a Bracke 1

12 WF102830 Washer M10*φ28*3t 1

13 WS100000 Spring Washer M10 1

14 SR101303 Cap Screw M10*65L 1

15 722359A Support Rib 1

16 WS080000 Spring Washer M8 3

17 WF082020 Washer M8*φ20*2t 3

18 SR080400 Cap Screw M8*20L 2

19 SS080200 Set Screw M8*1.25*10 4

20 NH081300 Hex Nut M8 2

21 722487 Fixed plate 1

22 721108 Roller 2

23 721111 Stage Screw 2


AB136457B+AB721097

AB136631A
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 136631 Stop Swatch B1 CE 1
2 709411 Outlet Beads PG11 1
3 IC722512 SWITCH CORD 0.5mm2*2C 1

AB721037-D
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721037 Door Safety Switch AZD-1001T 1
2 709411 Outlet Beads PG11 1
3 IC722513 SWITCH CORD 0.5mm2*2C 1
AB721364+AB721367

AB721037-E
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721037 Door Safety Switch AZD-1001T 1
2 709411 Outlet Beads PG11 1
3 IC722525 SWITCH CORD 0.5mm2*2C 1

AB722403D
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721406A Door Safety Switch AZ8-108H 1
2 722403A Adjustmen Plate 1
3 SM059400 Pan Head Screws Hexagon M5x16 2
4 IC722515 SWITCH CORD 0.5mm2*2C 1 (LS1)
5 721406-1 shaft 1
AB721037-C

AB721037-C
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721037 Door Safety Switch AZD-1001T 1
2 709411 Outlet Beads PG11 1
3 IC722012 SWITCH CORD 針
0.5mm2*2C*2 2Y 1 (SQ1)
AB721414A+AB722008

AB721414A
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721414 Digital PID Temperature Controller DTA7272R0 1
2 721341 Control Box 1 R
3 LM721001 Label 1
4 721388 Led Swatch AC24V 7
5 994808 Stop Swatch R2PNR4-1B-R 1
6 721397 Swatch AC24V 1
7 IC721001 CONNECT CORD 1007 24AWG (BK) 1
8 IC722002 CONNECT CORD 1007 24AWG (RED) 1

AB722008
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 136631 Stop Swatch B1 CE 1

2 709411 Outlet Beads PG11 1

3 IC722008 SWITCH CORD 0.5mm2*2C*190cm*2針2Y 1 (EM2)


AB721414A+AB722008

AB721414B
ITEM PART NO PARTS NAME SIZE Q`TY NOTE

1 721414 Digital PID Temperature Controller DTA7272R0 1

2 721341 Control Box 1 R

3 LM721001 Label 1

4 721388 Led Swatch AC24V 6

5 994808 Stop Swatch R2PNR4-1B-R 1

6 721397 Swatch AC24V 1

7 IC721001 CONNECT CORD 1007 24AWG 1

8 IC722002 CONNECT CORD 1007 24AWG 1

9 203230 Plug 1
AB722391

AB722391
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 722391 Press beam 1 T
2 SR081800 Cap Screw M8*1.25*90 1
3 722051 Roll Wheel 55
4 722052 Spacer Ring 56
6 NL081300 Nylon Nut M8*1.25 27
7 SR081200 Cap Screw M8x60 26
AB722399-2

AB722399-2
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 722398 L-Type Screw 1
2 NH081300 Hex Nut M8 4
3 WF083020 Washer M8*φ30*2T 3
4 WF081818 Washer M8*φ18*1.8T 6
5 BB608002A Ball Bearing 608ZZ 3
6 NF081300 Hex Flange Nut M8 5
7 722399 Fixed Block 1
8 SH081100 Hex Head Bolt M8*55L 2
9 WF082320 Washer M8*φ23*2T 4
10 NH081304 Hex Nut M8*4T(薄型) 2
11 WS080000 Spring Washer M8 2
AB722403A+AB722403B

AB722403A
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721406A Door Safety Switch AZ8-108H 1

2 722403A Adjustmen Plate 1

3 SM059400 Pan Head Screws Hexagon M5x16 2

4 IC722009 SWITCH CORD 0.5mm2*2C*180cm*2針2Y 1 (LS1)

5 721406-1 shaft 1

AB722403B
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721406A Door Safety Switch AZ8-108H 1

2 722403B Adjustmen Plate 1

3 SM059400 Pan Head Screws Hexagon M5x16 2

4 IC722021 SWITCH CORD 0.5mm2*2C*140cm 1 (LS3)

5 721406-1 shaft 1
AB722403D

AB722403D
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721406A Door Safety Switch AZ8-108H 1
2 722403A Adjustmen Plate 1
3 SM059400 Pan Head Screws Hexagon M5x16 2
4 IC722515 SWITCH CORD 0.5mm2*2C 1 (LS1)
5 721406-1 shaft 1
AB721406-1+AB721406-2

AB722403E
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721406A Door Safety Switch AZ8-108H 1
2 722403A Adjustmen Plate 1
3 SM059400 Pan Head Screws Hexagon M5x16 2
4 IC722516 SWITCH CORD 0.5mm2*2C 1
5 721406-1 shaft 1

AB722403F
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 721406A Door Safety Switch AZ8-108H 1
2 722403B Adjustmen Plate 1
3 SM059400 Pan Head Screws Hexagon M5x16 2
4 IC722519 SWITCH CORD 0.5mm2*2C 1
5 721406-1 shaft 1
AB722432+722492

AB722432
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 722432 Pueumatic Cylinder Ø20X180ST 1

2 722436 Ø6-PT1/8" 2

AB722492
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 722492 Proximity Sensor PM12-02NB-M12 1
2 722434 Limite Switch fixed plate 1
3 IC722011 SWITCH CORD 1 (PS3)
AB722471

AB722471
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 722471 Aluminium Base 1
2 721095 L-Type Joints EPL8-02 2
3 722477 L-Type Joints EPL4-02 2
4 721359 Plug ISH-02 1/4 2
5 722472 Joints 1
6 722473 Joints 1
7 721357 L-Type Joints EPL10-02 1
8 722479 T-Type Joints EPB6-02 1
9 721373 Valve Silencer 5
10 722474 Threaded Through EPC4-02 2
11 WS030000 Spring Washer M3 10
12 SP030800 Pan Head Screw M3*40 10
13 721351 Solenoid Valve 4V210-08-F-AC24V 4
14 721352 Solenoid Valve 4V210-08H-AS AC24V 1
15 721348B Nylon Tube 6*4 0.1 100mm
16 721361 L-Type Joints EPL6-M5 1
17 722476 L-Type Joints EPLL8-02 2
18 721360 Plug ISH-01 1/8 1
AB722478+AB722478A

AB722478

AB722478A
AB722482A+AB722511

AB722482A

AB722511
AB722563

AB722563
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 722358 Extension Bracket 1 VE
2 SJ050800 Button Head Screw M5*0.8*40 50
3 721424 Wheel 50
4 NL050800 Nylon Nut M5*0.8 50
5 NH081300 Nut M8 2
6 WF082320 Washer M8*φ23 2
7 721200 Buffer Blocks 2
8 SR080700 Cap Screw M8*35 2
AB722564

AB722564
ITEM PART NO PARTS NAME SIZE Q`TY NOTE
1 722564 Press beam 1 T
2 SR081800 Cap Screw M8*1.25*90 1
3 722051 Roll Wheel 69
4 722052 Spacer Ring 70
5 SR081200 Cap Screw M8x60 31
6 NL081300 Nylon Nut M8*1.25 34
7 SR081400 Cap Screw M8x70 2

También podría gustarte