INSTRUCTIONS and PARTS
NO. 618
6” ATLAS BACK GEARED
SCREW CUTTING LATHE
NO. 12A, 16A
ARMATURE LATHE
JULY, 1976
CLAUSING CORPORATION
KALAMAZOO, MICHIGAN 49007
NO. 124, 16h,
ARMATURE bATHE
68JULY, 1976
618 ATLAS 6 BACK GEARED
SCREW CUTTING LATHE
and
12A, 16A ARMATURE LATHE
INSTRUCTIONS FOR ORDERING REPAIR PARTS
IT 1S IMPORTANT TO FURNISH THE FOLLOWING INFORMATION IN ADDITION TO QUANTITY REQUIRED:
|. PART NUMBER
2. PART NAME
3. MODEL and SERIAL NUMBER ¢f machine too|-you'll find both on the metal plate otteched to machine.
ORDER REPAIR PARTS
FROM.
GLAUSING SERVICE CENTER
811 EISENHOWER DRIVE, SOUTH
GOSHEN, INDIANA 46526
TABLE OF CONTENTS FOR LATHE PARTS
UNIT ASSEMBLIES reli Screeners seit wad
CARRIAGE on:
HEADSTOCK .
LEAD SCREW, CHANGE GEARS, GEAR
GUARD and LATHE BED ; 7
COUNTERSHAFT ond TAILSTOCK. ... SaeieCOUNTERSHAFT
RACKET
NO. 6L-1
SIX INCH LATHE
MOUNTING
JAN, 1969 FILE NO. 6L-1
MOUNTING HOLES
TN LATHE LEG
Fie
MOUNTING LATHE
Place lathe of beneh ia approximately. position shown
in fagure 1. Hench top should be at least 20 by 34 inch
es. Froat edges of legs should be about 14" iow froat
ff bench top. Mark positions of four holes in lathe legs
faad drill heles to accommodate
lta as desiied
Next, bolt lathe to beach top and level bed by carefully
following instructions contained ia bullerin'*PROPERLY
LEVEL THE LATHE BED", This is a most important
step and should aot be alighted.
ROCKER LEVER (ln belt tension position)
BELT TENSION SCREMS
SOUNTERSHAFT SRACKET
SPINDLE BELT
Figure?
MOUNTING COUNTERSHAFT
“The four holes for the countershalt bracker may oow be
Jocared and drilled by following the dimensions in figure
1. Whis countershale bele tension screws (refer to figuce
2), in about the midway position, place spindle belt an
famullest step of coustershafe pulley aad Inegest cep of
spindle pulley. Bolt countershaft bracket lightly £0
beneh,
Pat cocker Levet in teasion position, thar is, so that the
hele tension sczews (refer to figure 2) zest op the smaller
‘of the two flat xpots on rosker shaft, Naw move eouneer-
shaft bracket oa i slotted holes so thar countersbalt
spindle is parallel with lathe spindle. More beacket
away from Tathe-vocil belt is tight and tighcen the four
mounting bolts, With bele tension sccews, adjuse belr #0
that with a moderate amount of pressure belt cen be de-
mepanedl nner dati conren stack ain ealeetapetley
tightening lockauts on belt tension screws.
MOUNTING MOTOR
Before mounting mocor, make al} electrical connections
‘tide poltey 9a mosor shaft so chae small step ie toward
motor. Place motor ia position shows fa figuce 2, wich
belt on small step of motor pulley sad on large step of
‘couoreeshafe pulley. Be swe rockershaft is still in cen-
‘sion position and pall motor as close (0 counrersbatt
Tracket ns bele will sllov, line op belt and’ bolt motor
1m bene, Cheek tension and alignment of both halts,
then tighten all mounting sstews of bolts sesursly.
Printed in USA,
The Book of the Springfield: A Textbook Covering all the Various Military and Sporting Rifles Chambered for the Caliber .30 Model 1906 Cartridge; Their Metallic and Telescopic Sights and the Ammunition Suited to Them