Astm C 599
Astm C 599
Astm C 599
1
C 599
TABLE 1 Maximum Temperature for Thermal Endurance 9.1.3 Flange Out-Of-RoundOut-of-round of the flanges
Nominal Pipe Size, in.
Sudden Temperature shall be measured on the conical portion of the flange at the
Difference, max F (C) distance from the plane of the flange face indicated in Table 4,
1 to 2 200 (93)
3 140 (78) TABLE 4 Out-of-Round of Flanges
4 122 (68)
6 180 (82) Measurement
Point (Distance
Nominal Size, Out-of-Round,
from Plane of
in. max, in. (mm)
Flange Face),
TABLE 2 Maximum Working Pressure for Glass Process Pipe
in. (mm)
and Fittings 1 to 3 12(12.7) 0.020 (0.51)
Recommended Working 4 to 6 12(12.7) 0.030 (0.76)
Nominal Pipe Size, in.
Pressure, max, psi (kPa)
1 to 2 50 (345)
3 40 (276)
and shall be within the requirements prescribed in Table 4.
4 35 (241) 9.2 Bow:
6 20 (138) 9.2.1 Bow for Pipe Diameters 1 in. and UpBow shall be
measured at the midpoint of the pipe on a flat supporting
surface so as to permit no bending due to mass. Bow shall not
of this test shall be that all tested ware shall pass. If one or exceed 0.0015 times the length of the pipe. The representative
more failures do occur, a second sampling twice the percentage maximum bow tolerances in Table 5 indicate the range.
of the first one shall be made and the ware tested. If there are
any failures in the second sampling, the entire sampling shall 10. Dimensions of All Pipe and Fittings
be rejected. 10.1 Straight Pipe (Dimensions)Dimensional specifica-
8.3 All pipe sizes are suitable for vacuum applications. tions for straight lengths shall be in accordance with Table 6.
10.2 Dimensions of Flange GrooveDimensional specifi-
9. Dimensions and Permissible Variations
cations for the flange groove shall be in accordance with Table
9.1 Flanges: 7.
9.1.1 Flange Face FlatnessMaximum permissible devia- 10.3 Spacers (Standard)Dimensional specifications for
tion from a flat plane across the face of the flange on all sizes spacers (standard) shall be in accordance with Table 8.
shall be 164 in. (0.4 mm). 10.4 Spacer (Beveled)Dimensional specifications of spac-
9.1.2 Flange Face SquarenessFlange faces of both pipe ers (beveled) shall be in accordance with Table 9.
and fittings shall be square to the pipe centerline within the 10.5 Fittings (Dimensions)Dimensional specifications for
limits prescribed in Table 3. common fittings shall be in accordance with Tables 10-20.
11. Inspection
TABLE 3 Flange Face Squareness
Squareness Measurement,
11.1 Inspection of the material shall be made at the point of
Nominal Pipe Size, in. delivery, unless otherwise agreed upon between the purchaser
max, in. (mm)
1 to 2
1 32 (0.8) and the seller.
3
3 64 (1.19)
4 116 (1.59) 12. Packaging
6 332 (2.38) 12.1 Pipe, fittings, and hardware shall be so packaged as to
prevent injury to them during transportation and handling.
9.1.2.1 Squareness of straight pipe lengths shall be mea- Those items packed in containers conforming to all construc-
sured by placing the pipe on rollers, located approximately 2 tion requirements of Consolidated Freight Classification as to
in. (51 mm) from each end, and butting one end against a flat bursting tests, size limit, and gross mass shall be considered as
plate perpendicular to the axis of the rollers. The pipe shall be being properly packed.
rotated and the length variation at the sealing surface shall be 12.2 All hardware items shall be packed in boxes separate
read with a suitable mechanism, such as a dial indicator. The from the pipe and fittings.
maximum reading shall not exceed that shown in 9.1.1 for the 13. Keywords
respective pipe size. 13.1 borosilicate; glass; pipe
9.1.2.2 Pipe fittings shall be measured for flange squareness
by a gage having flat plates constructed at the angle required by TABLE 5 Bow for Pipe Diameters 1 in. and Up
that fitting. One flange shall be firmly placed on one plate and Length, ft (m) Bow, max, in. (mm)
the difference between the remaining flange face and the other (0.75)
12 0.045 (1.14)
surface plate shall not exceed the amount shown in 9.1.1 for the 5 (1.5) 0.090 (2.29)
10 (3) 0.180 (4.57)
respective fitting size.
2
C 599
TABLE 6 Dimensional Specifications for Straight Lengths
3
C 599
TABLE 8 Dimensional Specifications for the Spacers (Standard)
4
C 599
TABLE 10 Ells
A, in. (mm)
Nominal
618 in.
Size, in.
(3.2 mm)
1 234(69.9)
112 312 (88.9)
2 4 (101.6)
3 5 (127)
4 7 (177.8)
6 9 (228.6)
5
C 599
TABLE 12 Reducer Ells
B, in. (mm)
Nominal A, in. (mm) B, in. (mm) Nominal A, in. (mm) Nominal A, in. (mm) B, in. (mm)
618 in. (3.2
Size, in. 618 in. (3.2 mm) 618 in. (3.2 mm) Size, in. 618 in. (3.2 mm) Size, in. 618 in. (3.2 mm) 618 in. (3.2 mm)
mm)
112 by 1 312 (88.9) 3 (76.2) 3 by 2 5 (127.0) 412(114.3) 6 by 1 9 (228.6) 5 (127.0)
2 by 1 4 (101.6) 3 (76.2) 4 by 1 7 (177.8) 4 (101.6) 6 by 112 9 (228.6) 512 (139.7)
2 by 112 4 (101.6) 312 (88.9) 4 by 112 7 (177.8) 412 (114.3) 6 by 2 9 (228.6) 6 (152.4)
3 by 1 5 (127.0) 312 (88.9) 4 by 2 7 (177.8) 5 (127.0) 6 by 3 9 (228.6) 612(165.1)
3 by 112 5 (127.0) 4 (101.6) 4 by 3 7 (177.8) 512 (139.7) 6 by 4 9 (228.6) 8 (203.2)
6
C 599
TABLE 13 (a) Tees
Nominal A, in. (mm) B, in. (mm) C, in. (mm) Nominal A, in. (mm) B, in. (mm) C, in. (mm)
Size, in. 618 in. (3.2 mm) 618 in. (3.2 mm) 618 in. (3.2 mm) Size, in. 618 in. (3.2 mm) 618 in. (3.2 mm) 618 in. (3.2 mm)
1 by 1 234 (69.9) 234 (69.9) 512 (139.7) 4 by 112 7 (177.8) 412 (114.3) 14 (355.6)
112 by 1 312 (88.9) 3 (76.2) 7 (177.8) 4 by 2 7 (177.8) 5 (127.0) 14 (355.6)
112 by 112 312 (88.9) 312 (88.9) 7 (177.8) 4 by 3 7 (177.8) 512 (139.7) 14 (355.6)
2 by 1 4 (101.6) 3 (76.2) 8 (203.2) 4 by 4 7 (177.8) 7 (177.8) 14 (355.6)
2 by 112 4 (101.6) 312 (88.9) 8 (203.2) 6 by 1 9 (228.6) 5 (127.0) 18 (457.2)
2 by 2 4 (101.6) 4 (101.6) 8 (203.2) 6 by 112 9 (228.6) 512 (139.7) 18 (457.2)
3 by 1 5 (127.0) 312 (88.9) 10 (254.0) 6 by 2 9 (228.6) 6 (152.4) 18 (457.2)
3 by 112 5 (127.0) 4 (101.6) 10 (254.0) 6 by 3 9 (228.6) 612 (165.1) 18 (457.2)
3 by 2 5 (127.0) 412 (114.3) 10 (254.0) 6 by 4 9 (228.6) 8 (203.2) 18 (457.2)
3 by 3 5 (127.0) 5 (127.0) 10 (254.0) 6 by 6 9 (228.6) 9 (228.6) 18 (457.2)
4 by 1 7 (139.7) 4 (101.6) 14 (355.6)
B, in. (mm)
Nominal A, in. (mm) B, in. (mm) Nominal A, in. (mm) B, in. (mm) Nominal A, in. (mm)
618 in. (3.2
Size, in. 618 in. (3.2 mm) 618 in. (3.2 mm) Size, in. 618 in. (3.2 mm) 618 in. (3.2 mm) Size, in. 618 in. (3.2 mm)
mm)
112 by 1 by 112 312 (88.9) 3 (76.2) 3 by 2 by 3 5 (127.0) 412 (114.3) 6 by 1 by 6 9 (228.6) 5 (127.0)
2 by 1 by 2 4 (101.6) 3 (76.2) 4 by 1 by 4 7 (177.8) 4 (101.6) 6 by 112 by 6 9 (228.6) 512 (139.7)
2 by 112 by 2 4 (101.6) 312 (88.9) 4 by 112 by 4 7 (177.8) 412 (114.3) 6 by 2 by 6 9 (228.6) 6 (152.4)
3 by 1 by 3 5 (127.0) 312 (88.9) 4 by 2 by 4 7 (177.8) 5 (127.0) 6 by 3 by 6 9 (228.6) 612 (165.1)
3 by 112 by 3 5 (127.0) 4 (101.6) 4 by 3 by 4 7 (177.8) 512 (139.7) 6 by 4 by 6 9 (228.6) 8 (203.2)
7
C 599
TABLE 14 Crosses
A, in. (mm) B, in. (mm) A, in. (mm) B, in. (mm) A, in. (mm) B, in. (mm)
Nominal Nominal Nominal
618 in. 618 in. 618 in. 618 in. 618 in. 618 in.
Size, in. Size, in. Size, in.
(3.2 mm) (3.2 mm) (3.2 mm) (3.2 mm) (3.2 mm) (3.2 mm)
1 by 1 223 (69.9) 234(69.9) 3 by 112 5 (127.0) 4 (101.6) 4 by 4 7 (177.8) 7 (177.8)
112 by 1 312 (88.9) 3 (76.2) 3 by 2 5 (127.0) 412 (114.3) 6 by 1 9 (228.6) 5 (127.0)
112 by 112 312 (88.9) 312 (88.9) 3 by 3 5 (127.0) 5 (127.0) 6 by 112 9 (228.6) 512 (139.7)
2 by 1 4 (101.6) 3 (76.2) 4 by 1 7 (177.8) 4 (101.6) 6 by 2 9 (228.6) 6 (152.4)
2 by 112 4 (101.6) 312 (88.9) 4 by 112 7 (177.8) 412 (114.3) 6 by 3 9 (228.6) 612 (165.1)
2 by 2 4 (101.6) 4 (101.6) 4 by 2 7 (177.8) 5 (127.0) 6 by 4 9 (228.6) 8 (203.2)
3 by 1 5 (127.0) 312 (88.9) 4 by 3 7 (177.8) 512(139.7) 6 by 6 9 (228.6) 9 (228.6)
8
C 599
TABLE 17 Caps
TABLE 18 Lateral Y
ANNEX
9
C 599
TABLE 19 Lateral Y Reducers
(Mandatory Information)
A1.1 Density2.24 g/cm3, measured at room temperature A1.4 Youngs Modulus9 000 000 to 10 000 000 psi
by Test Method C 693. (62 to 69 GPa) when measured at room temperature in
accordance with Test Method C 623.
A1.2 Thermal Conductivity0.73 Btuft/hft 2F (0.0035
calcm/scm2C), measured at room temperature.
A1.5 Tensile StrengthDue to effect of surface conditions
A1.3 Specific Heat0.20 Btu/lbF (0.20 cal/gC), mea- on ultimate strength, nominal design stress shall be 1000 psi
sured at 75C. (6.9 MPa).
10
C 599
The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection
with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such
patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM Headquarters. Your comments will receive careful consideration at a meeting of the responsible
technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your
views known to the ASTM Committee on Standards, 100 Barr Harbor Drive, West Conshohocken, PA 19428.
11