Ideal6550 95ep
Ideal6550 95ep
Ideal6550 95ep
IDEAL 4850-95 EP
IDEAL 5221-95 EP
IDEAL 6550-95 EP
Operating Instructions
Mode d'emploi
Gebruiksaanwijzing
Manuale d'istruzione
Instrucciones para el uso
2. Installation..............................................5
2.1 Preparing for installation.........................5
2.2 Power supply..........................................5
3.
Operation ...............................................6
Checklist ................................................6
3.1 Operating elements................................6
3.2 Start machine .........................................7
Cutting to specified dimensions..............7
Cut according to markings......................7
Eject function..........................................7
Repeat cutting ........................................7
Repeat dimension function completed....7
Cutting activation....................................7
Cutting stop or interruption .....................7
3.3 Programming..........................................8
Entering a program ................................8
Eject function:.........................................8
Programming of repeat cut dimension....8
Cancel a program...................................8
Working with programs...........................9
General ..................................................9
Escape the program mode .....................9
Program keys and :........................9
Display in cm or inch ..............................9
Adjust the eject-dimension .....................9
4.
4.1
4.2
4.3
4.4
IDEAL 5221-95 EP
Maintenance ........................................10
Safety check ........................................10
Cutting stick replacement .....................10
Setting the cutting depth.......................10
Turning resp. replacing the cutting stick10
Cutting test...........................................10
Blade replacement ...............................11
Blade demounting ................................11
Blade mounting ....................................11
Maintenance all 7 days.........................12
Maintenance all 6 months ....................12
Lubricant and grease gun.....................12
5.
6.
Technical data......................................14
7.
Accessories..........................................14
IDEAL 6550-95 EP
EG-declaration of conformity
01-01-23
B5221G1A.doc
General
1.1 Application
The machine is designed for cutting reams of
paper to a specified dimension. Dimension
setting may be performed via keys or manually
at the rotary control. The cutting takes place
through the "two-handed control system".
s Danger!
Non-compliance with the instructions may
endanger persons.
l Warning!
Non-compliance with the instructions may
cause damage to the machine.
l Warning!
The machine may only be used for cutting
paper or similar materials. Clips etc. will
damage the cutting blade.
s Danger!
The cutting of hard material or material
which might splinter is forbidden.
s Danger
Only instructed persons are allowed to
operate the machine.
No operation by children.
01-01-23
B5221G1A.doc
Installation
01-01-23
B5221G1A.doc
Operation
s Danger!
The machine may only be operated by
persons who have read and understood the
operating instructions and safety
instructions.
s Danger!
Check safety devices are complete and
function prior to starting the machine.
(1) Guard
(2) Two-hand activation
(3) Backgauge control
(4) Clamp returns
(5) Main switch
(6) Rotary control for backgauge setting
(7) Key switch
(8) Pre-clamping
(10) Dimensions display (cm or inch)
(11) - Programmable dimension
- Eject function
(12) Programmable dimension
(13) Stop & Clear; annulation & correction
(14) Start
(15) Memory / Dimension repeat
(16) Numerical keypad
(17) Changeover cm/inch.
(19) Clear program
(20) select program
(21) Enter
(22) Program number
(23) Program step
(24) Display repeat cut
(25) Specified dimension
Checklist
- Machine panels:
All panels must be mounted
- Cutting activation:
Open the safety guard (1).
The cutting mechanism starts through a "twohanded control system" (2). The cutting
mechanism should only start if the guard is
closed and the buttons of the two handed
control system are pressed exactly at the
same time.
- Guard didn't closed itself otherwise replace
the gasspring.
It is recommended to keep a check handbook.
Pre-clamping:
+
Clamp returns:
01-01-23
B5221G1A.doc
01-01-23
B5221G1A.doc
Entering a program
- Press P "PR" appears in the Display
- 1 ... 9 Enter program number 1....9.
First figure in Display = program number.
- 1 ... 9 Enter dimension 1....9, or move the
backgauge to the desired measurement with
the rotary control.
- = store the dimension next program step
appears.
- 1 ... 9 Enter the next dimension.
- = store the dimension.
- P+
Escape the program mode.
o
o
S
2 4.
# % .
Eject function
Pressing the keys = and simultaneously for
storing the dimension forces the backgauge
first to move to the front pushing out the paper ,
and then move to the entered dimension on the
display.
Programming of repeat cut dimension
- P press "PR" appears in the Display
- 1 ... 9 Enter program number 1....9.
First figure in display = program number
Second figure = program step.
- ... Enter program step 1...9.
- 1 ... 9 Enter repeat cut dimension.
- M N1 Display shows one repeat cut.
- M N1 Display shows two repeat cuts.
- M N1 Display shows three repeat cuts.
- M N .... Display shows ... repeat cuts.
Maximum nine repeat cuts can be entered.
Entering the tenth repeat cut will delete the
repeat cut and the display shows the actual
program step.
- = store the dimension.
P+
Cancel a program
- P press "PR" appears in the display.
- 1 ... 9 enter program number 1....9.
- Key
press two times.
Each program has to be cancelled separately.
Single program steps can only be overwritten.
Deleting the last program step.
- Enter 0.
- Press =.
P+
8
01-01-23
B5221G1A.doc
o
o
S
2 4.
# % .
Display in cm or inch
- Press mm inch Display changes between mm
and Inch.
Adjust the eject-dimension
- P + M P + M EJ on display.
- Insert the desired dimension.
- = Store dimension.
01-01-23
B5221G1A.doc
Maintenance
s Danger
- Maintenance work may only be performed by
trained staff.
- Replacement of blade and cutting stick may
only be performed when the main switch is
switched off.
- Disconnect from the mains before starting
any service work or before removing the
cover.
If the cutting stick (2) is very worn it must be
turned.
l Warning!
Too deep cutting into the cutting stick
shortens the life time of the blade.
Safety check
Perform a safety check every 5 years according
to 40 VBG 7i according to test specification
EBA WN 105 18 61. The execution of this
safety check must be confirmed on the test
protocol. A test badge must be fixed to the rear
of the machine.
Cutting test
- If the last sheet of paper of a stack is not cut
over its total length, Turn the screw (9) a half
turn to the right.
- Repeat this procedure until the paper is cut
over its total length.
- Turn the screw (9) a half turn to right.
- Perform cutting test as described below
10
01-01-23
B5221G1A.doc
l Warning!
Blades may only be sharpened by
specialists.
11
01-01-23
B5221G1A.doc
12
01-01-23
B5221G1A.doc
Trouble shooting
Malfunction:
Cutting may not be activated.
a) Cause:
Dimension was not approached correctly.
LED "S" does not go off.
s Danger!
Disconnect from the mains before starting
any sevice work or before removing the
cover.
Remedy:
press
once again.
b) Cause:
Safety check of the guard.
Remedy:
Open and close the guard.
c) Cause:
Measurement below 9,00 cm.
Remedy:
Press
until the backgauge has
reached the position.
d) Cause:
Backgauge not in the right position
CUT on Display.
Remedy:
Please inform the technical service.
Malfunction:
Display illumination off.
Malfunction:
Knife stops even though motor still
functions.
Cause:
Power supply.
Remedy:
- Mains switch on.
- Plug in mains plug.
- Check main fuse.
- Overload switch (9) on.
Cause:
The safety clutch was activated.
Remedy:
Contact your dealer.
Malfunction:
The last sheet of paper in a stack is not
completely cut.
Remedy:
Set cutting depth or turn resp. replace
cutting stick. (see chapter cutting stick
replacement).
Malfunction:
Poor cutting.
Remedy:
No clear cut despite the cutting depth is
correctly set and the cutting stick replaced
the cutting blade must be sharpened resp.
replaced.
13
01-01-23
B5221G1A.doc
Technical data
7.
Accessories
l Important!
Only fit accessories recommended by the
manufacturer.
Knocking up device
9000 521
< 20mm
IDEAL 5221-95 EP
Spare knife
6 cutting sticks
Side tables left and right
9000 130
9000 024
9000 530
IDEAL 4850-95 EP
14
Spare knife
Cutting sticks
9000 021
9000-022
IDEAL 6550-95 EP
Spare knife
Cutting sticks
9000 025
9000 026
01-01-23
B5221G1A.doc
EG-KONFORMITTSERKLRUNG
EC-declaration of conformity
Dclaration de conformit CE
Declaracin CE de conformidad
Dichiarazione CE di conformit
EG-verklaring van overeenstemming
Declaraao CE de conformidade
EF-overensstemmelseserklring
- Hiermit erklren wir, da die Bauart von
- Herewith we declare that
- Par la prsente, nous dclarons que
- Por la presente, declaramos que la
- Si dichiara che il modello della
- Hiermede verklaren wij, dat de in de handel gebrachte machine
- Com a presente, declaramos que o modelo da
- Hermed erklres, at produkttypen
4850-95 EP; 5221-95 EP; 6550-95 EP
- folgenden einschlgigen Bestimmungen entspricht:
- complies with the following provisons applying to it:
- sont conformes aux dispositions pertinentes suivantes:
- satisface las disposiciones pertinentes siguientes:
- conforme alle seguenti disposizioni pertinenti:
- voldoet aan de eisen van de in het vervolg genoemde bepalingen:
- est em conformidade com as disposies pertinentes, a saber:
- er i overensstemmelse med flgende bestemmelser:
EWG-RL 89/392; EWG-RL 73/23; EWG-RL 89/336
- Angewendete harmonisierte Normen insbesondere
- Applied harmonized standards in particular
- Normes harmonise utilises, notamment
- Normas armonizadas utilizadas particularmente
- Norme armonizzate applicate in particolare
- Gebruikte geharmoniseerde normen, in het bijzondere
- Normas harmonizadas utilizadas, em particular
- Harmoniserede standarder, der blev anvendt, i srdaleshed
EN60204; prEN1010-1; prEN1010-3; EN55014-1; EN55014-2;
EN6100-3-2; EN6100-3-3;
EN292; EN294 EN27779; EN349; DIN45635-27
Krug & Priester GmbH u. Co KG
72336 Balingen, Germany
19. 3. 2001
Datum
Wolfgang Priester
- General Manager -
11AVKon
http://www.ideal.de
01/2001
B5221G1A.doc