Aoc 917sw Tsum1pfr

19" LCD Color Monitor
AOC 917Sw
Service
Service
Service
Horizontal Frequency
30-83 KHz
TABLE OF CONTENTS
Description
Page
Description
Page
Table Of Contents...1
5.2.Electrical Block Diagram...............................16
Revision List2
6.Schematic..........................................18
Important Safety Notice.3
6.1.Main Board.............................................18
1. Monitor Specification......................................4
6.2.Power Board..............................................23
2. LCD Monitor Description.......5
6.3.Key Board...................................................25
3. Operation Instruction...............6
7.PCB Layout...........................................26
3.1. General Instructions..............................................6
7.1.Main Board...........................................26
3.2. Control Buttons........................................................6
7.2.Power Board.................................................28
3.3. OSD Menu.............................................................7
7.4.Key Board..........................................30
4. Input/Output Specification......................9
8. Maintainability............................................31
4.1. Input Signal Connector...............................9
8.1.Equipments and Tools Requirement...............31
4.2. Power Supply Requirements....................................9
8.2.Trouble Shooting.................................32
4.3. Factory Preset Display Modes.........................10
9. White-Balance, Luminance adjustment................38
4.4. Panel Specification...10
10. Monitor Exploded View...................................40
5. Block Diagram........................................................14
11.BOM List...............41
5.1. Software Flow Chart.....14
12.Different Parts List..................54
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
AOC 917Sw
Revision List
Version
Release Date
Revision History
TPV Model Name

T98SM5NBUWA1NN
T9RSM5NLUWCKNZ
T9RSM5NPUWA5NN
T9RSM5NPUWA5NG
A00
Feb.-17-2008
Initial release
T9RSM5NQUWA2NN
T9RSM5NQUWA3NN
T9RSM5NQUWA4NN
T9RSM5NKUWA2NN
AOC 917Sw
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment persons body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
AOC 917Sw
1. Monitor Specifications
LCD Panel
Resolution
Model number
917Sw
Driving system
TFT Color LCD
Viewable Image Size
481mm diagoanl
Pixel pitch
0.2835mm(H) x 0.2835mm(V)
Video
R, G, B Analog lnterface
Separate Sync.
H/V TTL
Display Color
16.7M Colors
Dot Clock
128 MHz
Horizontal scan range
30 kHz - 83 kHz
Horizontal scan Size(Maximum)
408.24mm
Vertical scan range
56 Hz - 75 Hz
Vertical scan Size(Maximum)
255.15mm
Optimal preset resolution
1440 x 900 (60 Hz)
Highest preset resolution
1440 x 900 (60 Hz)
Plug & Play
VESA DDC2B/CI
Input Connector
D-Sub 15pin
Input Video Signal
Analog: 0.7Vp-p(standard), 75 OHM, Positive
Power Source
100~240VAC, 47~63Hz
Power Consumption
Active < 37W

Standby < 1W
Connector Type
15-pin Mini D-Sub
Signal Cable Type
Detachable
Dimensions & Weight:

Physical
Height (with base)
439 mm
Characteristics Width
358 mm
Depth
204 mm
Weight (monitor only)
3.8 kg
Weight (with packaging)
4.7 kg
Temperature:
Operating
0 to 50
Non-Operating
-20to 60
Humidity:
Environmental Operating
Non-Operating
10% to 85% (non-condensing)

5% to 80% (non-condensing)
Altitude:
Operating
0~ 3000m (0~ 10000 ft )
Non-Operating
0~ 5000m (0~ 15000 ft )
AOC 917Sw
2. LCD Monitor Description

The LCD monitor will contain a main board, a power board and a key board which house the flat panel control logic,
brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Monitor Block Diagram
Flat Panel and
CCFL Drive.
CCFL backlight
Power board
(Include: adapter, inverter)
Main Board
RS232 Connector
For white balance
adjustment in factory
mode
Key Board
Video signal, DDC
AC-IN
HOST Computer
100V-240V
AOC 917Sw
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at the front of the
panel of the monitor.
By changing these settings, the picture can be adjusted to your personal preferences.
-
The power cord should be connected.
Connect the video cable from the monitor to the video card.
Press the power button to turn on the monitor, the power indicator will light up.
3.2 Control Buttons

3.2.1 Key Control
1. Eco Mode / Up 2. Exit / - 3. Menu / + 4. Auto / Down 5. Power on/off
3.2.2 Key Function

1) Press the MENU-button ( ) to activate the OSD window.
2) Press
or
to navigate through the functions. Once the desired function is highlighted, press the MENU-button
to activate sub-menu . Once the desired function is highlighted, press MENU-button to activate it.
3) Press
or
to change the settings of the selected function. Press
or
to select another function in
sub-menu . Press AUTO( ) to exit . If you want to adjust any other function, repeat steps 2-3.
4) OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off
and then press power button to turn the monitor on.
5) Eco Mode hot key ( ) : Press the Eco key continuously to select the Eco mode of brightness when there is no
OSD ( Eco mode hot key may not be available in all models).
6) Volume adjustment hot key : When there is no OSD , press Volume ( ) to active volume adjustment bar, press
or
to adjust volume ( Only for the models with speakers).

3.3 OSD Menu
AOC 917Sw
OSD Function Introduction

Luminance
Adjust Range
Description
Brightness
0-100
Backlight Adjustment
Contrast
0-100
Contrast from Digital-register
Standard
Standard Mode
Text
Text Mode
Internet
Internet Mode
Game
Game Mode
Movie
Movie Mode
Sports
Sports Mode
Gamma1
Adjust to Gamma 1
Gamma2
Adjust to Gamma 2
Gamma3
Adjust to Gamma 3
Off
Disable dynamic contrast ratio
On
Enable dynamic contrast ratio
Clock
0-100
Adjust picture Clock to reduce Vertical-Line noise.
Focus
0-100
Adjust Picture Phase to reduce Horizontal-Line noise
H.Position
0-100
Adjust the horizonal position of the picture.
V.Position
0-100
Adjust the vertical position of the picture
Eco mode
Gamma
DCR
Image Setup
Color Temp.
Warm
Recall Warm Color Temperature from EEPROM.
Normal
Recall Normal Color Temperature from EEPROM.
Cool
Recall Cool Color Temperature from EEPROM.

7
AOC 917Sw
sRGB
Recall SRGB Color Temperature from EEPROM.

User-B
Blue Gain from Digital-register
User-G
Green Gain Digital-register.
User-R
Red Gain from Digital-register
User-Y
Yellow Gain from Digital-register
User-C
Cyan Gain from Digital-register
on or off
Disable or Enable Full Enhance Mode
Nature Skin
on or off
Disable or Enable Nature Skin Mode
Green Field
on or off
Disable or Enable Green Field Mode
Sky-blue
on or off
Disable or Enable Sky-blue Mode
AutoDetect
on or off
Disable or Enable AutoDetect Mode
Demo
on or off
Disable or Enable Demo
Frame Size
0-100
Adjust Frame Size
Brightness
0-100
Adjust Frame Brightness
Contrast
0-100
Adjust Frame Contrast
Hue
0-100
Adjust Frame Hue
Saturation
0-100
Adjust Frame Saturation
H. position
Adjust Frame horizontal Position
V.position
Adjust Frame vertical Position
H.Position
0-100
Adjust the horizontalposition of OSD
V.Position
0-100
Adjust the vertical position of OSD
Timeout
0-100
Adjust the OSD Timeout
User
Color Boost
Full
Enhance
Picture
Boost
Position
OSD Setup
Language
Select the OSD language
Extra
Auto Config
yes or no
Auto adjust the picture to default
Reset
yes or no
Reset the menu to default
DDC-CI
Information
Turn ON/OFF DDC-CI Support

Show the information of the main image and
sub-image source
AOC 917Sw
4. Input/Output Specification
4.1 Input Signal Connector
Analog connectors
Pin No.
Description
Pin No.
Description
1.
Red Video
9.
+5V
2.
Green Video
10.
Ground
3.
Blue Video
11.
N.C.
4.
N.C.
12.
DDC-Serial Data
5.
Detect Cable
13.
H-Sync
6.
Red Ground
14.
V-Sync
7.
Green Ground
15.
DDC-Serial Clock
8.
Blue Ground
VGA connector layout
10
11
15
4.2 Power Supply Requirements

A/C Line voltage range
100 V ~ 240 V
A/C Line frequency range
50 3Hz, 60 3Hz
Current
1.5A max at 100V; 0.8A max at 240 V
Peak surge current
< 55A peak at 240 VAC and cold starting
Leakage current
< 3.5mA
Power line surge

DC output Voltage
CURRENT
No advance effects (no loss of information or defect)

with a maximum of 1 half-wave missing per second
: 5VDC 5; 12VDC 5
1.5Amp (5V) 2 Amp (12V)

4.3 Factory Preset Display Modes
Horizontal
Vertical
Frequency(Khz)
Frequency(Hz)
720 400
31.47kHz
70.0Hz
640 480
31.47kHz
60.0Hz
640 480
37.50kHz
75.0Hz
800 600
37.879kHz
60.0Hz
800 600
46.875kHz
75.0Hz
1024 768
48.363kHz
60.0Hz
1024 768
56.476kHz
70.0Hz
1024 768
60.021kHz
75.0Hz
1280 1024
64.000kHz
60.0Hz
1280 1024
80.000kHz
75.0Hz
1440 900
55.935kHz
59.8Hz
Stand
Resolution
Dos-mode
VGA
SVGA
XGA
SXGA
WXGA
AOC 917Sw
4.4 Panel Specification

4.4.1 General Features
10
AOC 917Sw
4.4.2 Display Characteristics
11
AOC 917Sw
4.4.3 Optical Characteristics
12
AOC 917Sw
4.4.4 Electrical Characteristics

(1) TFT-LCD
(2) Backlight
13
AOC 917Sw
5. Block Diagram
5.1 Software Flow Chat
1
N
4
5
Y
6
Y
9
10
11
Y
N
12
13
Y
14
15
Y
17
18
19
Y
14
16
AOC 917Sw
1) MCU initialize.
2) Is the EPROM blank?
3) Program the EPROM by default values.
4) Get the PWM value of brightness from EPROM.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EPROM.
Turn on the LED and set it to green color.
Scalar initializes.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappear.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
15

5.2 Electrical Block Diagram
AOC 917Sw
5.2.1 Main Board
Crystal 14.318MHZ
Panel Interface
(X401)
(CN403)
Scalar TSUM1PFR
FLASH ROM
SST25LF020A
(Include ADC, OSD, MCU)
(U402)
(U401)
D-Sub Connector
(CN101)
16
Key Control Interface

(CN402)
AOC 917Sw
5.2.2 Inverter/Power Board
AC input
Bridge
Rectifier
and Filter
EMI filter
Rectifier
diodes
Transformer
Start Circuit: R932, R933
CN902
5V
Feedback
Circuit
PWM
Control IC
12V
ON/OFF
Output
Circuit
Lamp
Transformer
MOSFET
Feedback
Circuit
PWM
Control IC
Over Voltage
IC801
17
ON/OFF
Control
DIM
AOC 917Sw
6. Schematic
6.1 Main Board
715G2904
TSUM1PFR
SCHEMATIC
XGA/SXGA
DSUB_5V
ESD_VCC
DSUB_5V
VCC3.3
ESD_VCC
LVDS OUTPUT
DSUB_R+
DSUB_RDSUB_G+
DSUB_GDSUB_SOG
DSUB_B+
DSUB_BDSUB_H
DSUB_V
DDC1_SDA
DDC1_SCL
DET_CABLE
DSUB_R+
DSUB_RDSUB_G+
DSUB_GDSUB_SOG
DSUB_B+
DSUB_BDSUB_H
DSUB_V
DDC1_SDA
DDC1_SCL
DET_CABLE
VCC3.3
VCC1.8
VCC3.3
VCC1.8
CMVCC
VCC3.3
CMVCC1
CMVCC
CMVCC1
02.Input
VCC1.8
CMVCC
VCC3.3
DSUB_5V
CMVCC
CMVCC1
VCC1.8
ESD_VCC
PA[0..1]
on_BACKLIGHT
VCC3.3
DSUB_5V
CMVCC
PA[0..1]
on_BACKLIGHT
Mute
Volume#
PANEL_ID#
Mute
Volume#
PANEL_ID#
Adj_BACKLIGHT
PA[4..9]
PA[4..9]
PB[0..9]
PB[0..9]
PPWR_ON#
PA[0..1]
PA[4..9]
CMVCC
PB[0..9]
PPWR_ON#
Adj_BACKLIGHT
VCTRL
VCTRL
CMVCC1
ESD_VCC
05.Power
03.Scalar
T P V ( Top
Victory
Electronics
Co . ,
Date
OEM MODEL
Size
TPV MODEL

Key Component
Ltd. )
04.Output
01.Top
PCB NAME
Friday , February 29, 2008
18
Sheet
Rev
715G2904-1
3
of
A
1
<>
AOC 917Sw
H_Sy nc
V_Sy nc
R101 0R05 1/10W 5%
DDC1_SDA
13
DSUB_SDA
12
11
17
DDC1_SDA
R113
100R 1/16W 5%
VGA_BVGA_B+
VGA_GVGA_G+
VGA_RVGA_R+
DSUB_5V
R109
ZD103
UDZSNP5.6B
FB103
VGA_G+
DB15
VGA_G-
BEAD
5pF/50V
R114
DSUB_R+
VGA_RESD_VCC
DSUB_R-
0.047uF
C110
100R 1/16W 5%
C111
75R 1/16W 5%
ESD_VCC
I/O1 I/O4
GNDVDD
I/O2 I/O3
DSUB_G-
C109
R115
2
R116
DSUB_SCL
0.047uF
100R 1/16W 5%
VGA_R+
6
5
4
DSUB_G+
C107
100R 1/16W 5%
C108
R112
DGND
1
2
3
0.047uF
R111
BEAD
FB101
DSUB_SDA
DSUB_SOG
C106
390 OHM 1/16W
ZD104
UDZSNP5.6B
75R 1/16W 5%
U103
VGA_PLUG
2
DSUB_5V
Connect Pin4 and Pin11 of CN101 to

GND to prevent ESD issue.
GND POWER
DSUB_B0.047uF
DSUB_5V
10
5
9
4
8
3
7
2
6
1
15
C105
100R 1/16W 5%
DSUB_SCL
DSUB_B+
0.047uF
5pF/50V
R108
CN101
R110
100R 1/16W 5%
C101
100R 1/16W 5%
C104
75R 1/16W 5%
14
R104
BEAD
VGA_B-
10K 1/16W 5%
DDC1_SCL
FB102
1
R107
R121
DDC1_SCL
R106
C102 C103
2K2 1/16W 5%
22pF 22pF
R105
2K2 1/16W 5%
5
5
16
10K 1/16W 5%
DSUB_H
DSUB_V
VGA_B+
VCC3.3
R120
R102 100R 1/16W 5%

R103 100R 1/16W 5%
H_Sy nc
0.047uF
5pF/50V
R117
C113
100R 1/16W 5%
0.047uF
V_Sy nc
C115
NC
AZC099-04S
Prevent EDID Tool Issue

VCC3.3
U102
VGA_G+
VGA_R+
1
2
3
I/O1 I/O4
GNDVDD
I/O2 I/O3
AZC099-04S
ESD_VCC
6
5
4
VCC3.3
VGA_B+
R118
1K 1/16W 5%
C114
NC
VGA_PLUG
T P V ( Top
Victory
Electronics
Key Component
Date
19
02.Input
Co . ,
Ltd. )
DET_CABLE
OEM MODEL
Size
TPV MODEL
Rev
PCB NAME
Sheet
715G2904-1
4
of
B
1
<>
AOC 917Sw
AVDD VDDP
VDDC
RIN0P
RIN0M
GIN0P
GIN0M
SOGIN0
BIN0P
BIN0M
HSY NC0
VSY NC0
DDCA_SDA/RS232_TX
DDCA_SCL/rs232_RX
30
53
VDDC
VDDC
51
VDDP
13
12
10
9
11
8
7
16
17
18
19
DSUB_R+
DSUB_RDSUB_G+
DSUB_GDSUB_SOG
DSUB_B+
DSUB_BDSUB_H
DSUB_V
DDC1_SDA
DDC1_SCL
AVDD_ADC
3
3
3
3
3
3
3
3
3
3
3
VCC3.3
U401
VCTRL
LVA3P
LVA3M
52
33
34
VCTRL
35
36
37
38
39
40
PA[0..1]
PA4
PA5
PA6
PA7
PA8
PA9
PA[4..9]
PB[0..9]
4
R403 390 OHM 1/16W
AVDD
VCC3.3
C401
0.1uF/16V
C408
0.22uF16V
R408
1
2
WP 3
4
8
7
6
5
CE# VDD
SO HOLD#
WP# SCK
VSS
SI
R456
R457
R405
SST25LF020A-33-4C-SAE
CMVCC1
0R05 1/16W
0R05 1/16W
54
10K 1/16W 5%
C411 22pF
C412 22pF
R401
0R05 1/16W
R417
X401
14.31818MHz
1
C410
10uF/50V
21
22
23
24
28
100R 1/16W 5%
CMVCC1
14
REXT
REFM
0R05 1/16W
R402
300OHM
C403
C404
0.1uF/16V
0.1uF/16V
VDDC
VCC1.8
C406
C407
0.1uF/16V
0.1uF/16V
EE_WP
REFP
R425
C418
NC
NC
CMVCC
TSUM1PFR-LF
U402
10K 1/16W 5%
LVDS
SDO
SCZ
SCK
SDI
CMVCC
GPIO_P15/PWM0
PWM2/GPIO_P24
GPIO_P12
PWM1/GPIO_P25
RSTN
GPIO_P00/SAR1
GPIO_P01/SAR2
GPIO_P27/PWM1
RST
GPIO_P06
GPIO_P07
PWM0/GPIO_P26
GPIO_P13
GPIO_P14
XIN
20
27
R424
NC
55
56
57
58
59
60
61
62
63
64
on_BACKLIGHT
adj_BACKLIGHT
7
7
Volume#
Mute
R426
100R 1/16W 5%
R452
NC
MSDA
R420
100R 1/16W 5%
POWER_KEY #
R451
NC
MSCL
PANEL_ID#
R406
10K 1/16W 5%
R409
20K OHM 1/16W
KEY 2
KEY 1
R411
R412
100R 1/16W 5%
100R 1/16W 5%
R414
R410
R418
LED_GRN/BLUE
120R 1/16W 5%
LED_ORANGE
120R 1/16W 5%
NC/100R 1/16W 5%
R419
100R 1/16W 5%
C409 0.1uF/16V
XOUT
VCC3.3
GPIO_P10/I2C_MCL
GPIO_P11/I2C_MDA
MODE[0]
MODE[1]
R413
PPWR_ON#
DET_CABLE
100R 1/16W 5%
6
4
R453
R454
R455
NC
NC
NC
MSCL
MSDA
GND
GND
GND
31
32
26
25
C429
EE_WP
3
5
29
15
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
PB[0..9]
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
AVDD
FB401
VCC1.8
PA[4..9]
41
42
43
44
45
46
47
48
49
50
PA0
PA1
PA[0..1]
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
VDDP
VCC3.3
8
7
6
5
U403
VCC NC
WC E1
SCL E2
SDA VSS
1
2
3
4
NC
NC / M24C04-WMN6TP
VCC3.3
CN401
R421
R427
10K 1/16W 5%
3.9K OHM 1/16W
CN402
R428
3.9K OHM 1/16W
KEY 1
KEY2
POWER_KEY#
LED_GRN/BLUE
LED_ORANGE
1
2
3
4
5
6
CONN
C413
C414
C415
C416
R404
C417
R407
0.1uF/16V
0.1uF/16V
0.1uF/16V
0.1uF/16V
10K 1/16W 5%
0.1uF/16V
10K 1/16W 5%
POWER_KEY #
R429
R430
R431
R432
LED_ORANGE
LED_GRN/BLUE
NC
NC
NC
NC
KEY _LEFT
KEY _RIGHT
KEY _AUTO
1
2
3
4
5
6
7
8
NC \ CONN
T P V ( Top
Victory
Electronics
Key Component
Date
20
03.Scalar
Co . ,
Ltd. )
OEM MODEL
Size
TPV MODEL
Rev
PCB NAME
Sheet
715G2904-1
5
of
C
1
<>
AOC 917Sw
PANEL_VCC
CN403
PA[0..1]
PA[0..1]
PB[0..9]
PB[0..9]
PA0
PA1
5
PA[4..9]
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB8
PB9
PA[4..9]
PA4
PA5
PA6
PA7
PA8
PA9
R434
C420
330 OHM 1/4W
0.1uF/16V
PA0
PA1
PB2
PB3
PA4
PA5
PA6
PA7
PA8
PA9
PB0
PB1
PB2
PB3
3D
1
G
CMVCC
CMVCC
R435
R433
C419
10K 1/16W 5%
0.1uF/16V
Q405
AO3401
4K7 1/16W 5%
R436
100K 1/16W 5%
5
PPWR_ON#
PPWR_ON#
Q404
PMBS3906
2
S
PB4
PB5
PB6
PB7
PB8
PB9
AO3401L
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PANEL_VCC
CONN
FB402
C421
120OHM
+
100uF25V
T P V ( Top
Victory
Electronics
Co . ,
Date
OEM MODEL
Size
TPV MODEL
Key Component
Ltd. )
04.Output
PCB NAME
21
Sheet
Rev
715G2904-1
6
of
A
1
<>
AOC 917Sw
ESD_VCC 2
DSUB_5V
CMVCC
1
DSUB_5V 2
5, 6 CMVCC
D403
BAT54C
VCC3.3
D401
BAV99
1
2
3
4
5
6
7
8
9
CMVCC
CMVCC
BKLT-VBRI
BKLT-EN
C_PANEL_INDEX
Volume
Mute
SM340A
D402
CN404
CMVCC1
CMVCC1
R450
NC
NC(R0402)
NC
R439
10K 1/16W 5%
10K 1/16W 5%
Q409
KN2907AS
R440
4K7 1/16W 5%
CONN
VCC3.3
VCC1.8
on_BACKLIGHT
NC
VCC3.3
CMVCC1
VCTRL
MVCC
R441
NC/10K 1/16W 5%
adj_BACKLIGHT
100R 1/16W 5%
100uF25V
VCC3.3
Q408
NC/2N3904S-RTK/PS
R442
+ C423
NC
VIN
VOUT
ADJ(GND)
Volume
1K 1/16W 5%
BKLT-VBRI
R447
NC
C432
0.1uF/16V
FB403
VCC3.3
R446
VCC1.8
Q410
KN2907AS
Q406
2N3904S-RTK/PS
C425
Mute
VCC3.3
R437
BKLT-EN
R449
PANEL_ID#
VCC3.3
+ C426
100uF25V
Volume#
C428
0.1uF/16V
3
2
1
VCC3.3
U404
AP1117D33LA
C422
0.1uF/16V
R448
NC/4K7 1/16W 5%
T P V ( Top
Victory
Electronics
Key Component
Date
22
05.Power
Co . ,
Ltd. )
4, 5
+ C427
100uF25V
OEM MODEL
Size
TPV MODEL
Rev
PCB NAME
Sheet
715G2904-1
7
of
B
1
<>

6.2 Power Board
AOC 917Sw
715G2538-5
100 1/4W R918
1K 1/4W 1K 1/4W 1K 1/4W
C905
100uF/450V
R904
4K7 1/4W
R905
NC
C906
1500pF 2KV
R932
4K7 1/4W
R906
NC
D900
PR1007R
R935 100 1/4W
6
4
11
R961 100 1/4W
FB901
BEAD
1
2
3
4
12
Vcc
DRAIN
GND
HVS
PROTECT DRIVER
CTRL
SENSE
8
7
6
5
D903
BAW56
IC901
TEA1530AT
C902
0.001uF/250V
C901
0.001uF/250V
R915
220K 1/8W
R913
NC
R911
1K 1/8W
C909
0.22uF/50V
L901
R931
8K2 1/8W
C928
0.0012uF
HS1
HEAT SINK(D906)
4.0A/250V
IC903
PC123X2YFZOF
R925
1K 1/10W 1%
IC904
KIA431A-AT/P
FG
R923
R927
3.6K 1% 1/10W
ZD922
RLZ5.1B
D915
IN4148W
C924
0.01uF/16V
D916
IN4148W
R926
10K 1% 1/10W
R942
1K 1/10W 1%
9
8
7
6
5
4
3
2
1
+5V
HS2
NC
1
2
HS3
HEAT SINK(Q901)
F901
FUSE
SOCKET
1K5 1/10W
+12V
VAR901
NC
R940
33K 1/10W
R924
ZD921
RLZ16B
C921
0.0047UF/400V
1
2
C916
0.1uF
R930
2.4K 1% 1/10W
R902
R901
680K 1/4W 680K 1/4W
NR901
NTCR
+ C939
1000uF/25V
C903
0.47uF/275V
R903
680K 1/4W
D907
NC
2
4.0mH
1
C915
470uF/16V
R914
0.22 2W
R916
1K5 1/8W
FG
3
+5V
Q901
STP10NK70ZFP
R910
R938
10R 1/4W
R917
10K 1/8W
1K 1/8W
R912
22K 1% 1/8W
C911
0.22uF/25V
R967
0R05 1/4W
L903
1.1uH
POWER X'FMR
L902
R936
NC
D905
SB1060FCT
R962 100 1/4W
6
1
C910
0.001uF
C929
0.001uF
ZD901
NC
R907
NC
R929
1K 1/8W
R933
4K7 1/4W
Q902
10
C922
NC
D906
SP10100
C908
22uF/50V
R909
10R 1/4W
C907
0.1uF
D901
PS102R
VCC
C918
680uF/25V
PMBS3904
C938
1500pF 2KV
100K 2W
BD901
KBP208G
R908
T901
+12V
ZD902
RLZ16B
R928
C917
680uF/25V
100 1/4W R920
R921
C912
0.001uF
F902
0R05 1/4W
1K 1/4W
L904
1.1uH
R922
100 1/4W R919
1
2
C931
C930
0.1uF
0.1uF
CN902
WIRE HARNESS
DIM
GND1
GND
1
2
ON/OFF
FG
1
CN901
OEM MODEL 19'LCD
Size
G2538-3-X-X-12-070927
TPV MODEL
PWPC942SEE1
Rev
Key Component
02.POWER
PCB NAME
715G2538 3
TPV
Date
23
( Top
Victory
Electronics
Co . ,
Thursday , September 27, 2007
Ltd. )
Sheet
of
B
C
<>
AOC 917Sw
R855 C839
33 1/4W
1000pF
F801
0R05 1/4W
T801
POWER X'FMR
8
C802
470uF/25V +
3.6K 1/10W
R819
R804
100 1/8W
Q801
PMBS3904
Q808
PDTA144WK
R839
Q804
PMBS3906
1
ON/OFF
0 1/8W
Q805
PDTC144WK
C824
0.1uF
Q802
AM9945N-T1-PF
5
G
D
S
6
7
R856
33 1/4W
D805
BAW56
1
1
R801
1.5K 1/10W 1%
2
1
R828
10K 1/10W
R857
33 1/4W
C840
1000pF
R822
1K 1/10W 1%
C823
0.0022uF
T802
POWER X'FMR
8
C803
470uF/25V +
C805
0.1uF
0 1/8W
R858
33 1/4W
3
2
1
Q803
AM9945N-T1-PF
5
G
D
S
D802
BAV99
C811
10pF/6KV
9
E
3
R827
3.6K1/10W
C
B
2
1
2
D808
BAW56
1
R833
10K 1/10W
R809
1K 1/10W 1%
C815
0.0022uF
3
1
R815
1.5K 1/10W 1%
D803
BAV99
2
1
R834
10K 1/10W
R808
10K 1/10W
R813
10K 1/10W 1%
D817
IN4148W
R812
1K 1/10W 1%
2
C816
0.0022uF
CN804
CONN
3
1
Q810
RK7002
R811
2.4K 1% 1/10W
CN803
CONN
C841
1000pF
R853
68K 1% 1/10W
C835
NC
CN802
CONN
R814
1.5K 1/10W 1%
4
3
R851
R802
82K 1% 1/10
10KOHM +-1% 1/10W
D801
BAV99
R850
Q806
PMBS3904
CN801
CONN
C838
1000pF
3.6K 1/8W
Q812
PMBS3906
1
R821
1K 1/10W 1%
2
Q811
PMBS3904
DIM
R817
10K 1/10W
C801
10pF/6KV
R823
C807
0.1uF/25V
2
1
C819
0.0022uF
4
3
+12V
R816
1.5K 1/10W 1%
D809
IN4148W
D804
BAV99
R841
68K 1% 1/10W
R829
22R 1/8W
C842
0.01uF
R825
22R 1/8W
R837
47K 1/8W
C822
1uF/25V
R832
10K 1/10W
R806
68K 1% 1/10W
IC801
1
2
3
4
5
6
7
8
JR803
0 OHM +-5% 1/4W

C821
0.1uF/25V
IN1+
IN1FB
DTC
CT
RT
GND
C1
IN2+
IN2VREF
CONT
VCC
C2
E2
E1
R818
1K 1/10W 1%
R854
68K 1% 1/10W
Q807
PMBS3904
NC
R863
R831
2.4K 1% 1/10W
D806
IN4148W
TL494
R861
390K 1% 1/10W
R810
51K 1/8W
R820
47K 1/10W
D814
IN4148W
16
15
14
13
12
11
10
9
C820
220pF
R805
NC
C817
NC
R826
1K 1/10W 1%
Q809
RK7002
R803
1M 1/10W 5%
R807
47K 1/10W
C825
0.1uF/25V
R824
1K 1/10W 1%
C846
NC
C845
2.2uF/16V
R862
1M 1/10W 5%
C834
0.1uF/25V
OEM MODEL 19'LCD
Size
G2538-3-X-X-12-070927
TPV MODEL PWPC942SEE1
Rev
Key Component
03.INVERTER
PCB NAME
T P V ( Top
Date
24
R835
1M 1/10W 5%
Victory
Electronics
Co . ,
Thursday , September 27, 2007
Ltd. )
Sheet
715G2538 3
3
of
Custom
1
<>

6.3 Key Board
AOC 917Sw
715G2834-1
CN001
LBADC1
LBADC2
DC_POWERON
LED_GRN#
LED_RED# LED_RED#
2K 1/10W
R002
0R05 1/10W 5%
R003
R004
2K 1/10W
1K 1/10W 5%
SW
2
SW003
C007
NC/0.001uF
2POWER_ KEY
3
ZD001
SW
2
C008
NC/0.001uF
NC
SW
2
SW
2
C006
4
NC/0.001uF
NC/RLZ36B
SW
GND
4
AMBER
5
1
MLVS0603M04
SW001
ZD004
4
NC/0.001uF
NC/RLZ36B
NC
ZD008
C009
ZD002
SW005
SW002
ZD005
GND
MENU
SW004
C002
NC/0.001uF
C001
NC/0.001uF
UP
C004
NC/0.001uF
OK
C003
NC/0.001uF
DOWN
LED_GRN#
C005
NC/0.001uF
CONN
R001
1
2
3
4
5
6
GND
6
BLUE
LED_RED#
LED_GRN#
MLVS0603M04
2
ZD007
R005
4K7 1/10W 5%
R006
4K7 1/10W 5%
Q001
PMBS3904
Q002
PMBS3904
ZD006
MLVS0603M04
GND
GND
T P V ( Top
Victory
Electronics
Date
Ltd. )
OEM MODEL
Size
TPV MODEL
Key Component
Co . ,
2.0.key pad
Thursday , August 09, 2007
25
PCB NAME
Sheet
Rev
715G2834-1
2 of
2
B
B
AOC 917Sw
7. PCB Layout
7.1 Main Board
715G2904
26
AOC 917Sw
27

7.2 Power Board
AOC 917Sw
715G2538-5
28
AOC 917Sw
29

7.3 Key Board
AOC 917Sw
715G2834-1
30
AOC 917Sw
8. Maintainability
8.1 Equipments and Tools Requirement
1.
Voltmeter.
2.
Oscilloscope.
3.
Pattern Generator.
4.
DDC Tool with an IBM Compatible Computer.
5.
Alignment Tool.
6.
LCD Color Analyzer.
7.
Service Manual.
8.
User Manual.
31

8.2 Trouble Shooting
AOC 917Sw
8.2.1 Main Board

No power
No power
Press power key and look if the

picture is normal
NG
Please reinsert and make sure the
AC of 100V-240V is normal
NG
Reinsert or check the

power section
OK
Check C423(+)=1.8V
U404 Vout=3.3V
OK
NG
Replace CN404, Q410, Q409, U404
Check if X401 oscillate

waveforms are normal
NG
Replace X401
OK
Replace U401
32
AOC 917Sw
No picture (LED orange)

No picture
The button if under
NG
X401 oscillate
waveform is normal
control
NG
Replace X401
OK
OK
Check reset circuit of
U401 is normal
Check C423(+)=1.8V;
NG
Check Correspondent
component
OK
U404 Vout=3.3V
Replace U401
OK
NG
Check X401 oscillate

waveform is normal
Replace CN 404, Q410, Q409, U404

NG
OK
Replace X401
Check HS/VS from

CN101 is normal
NG
OK
Check Correspondent
component
Replace U401
33
AOC 917Sw
White screen
White screen
Measure Q404 base
NG
X401 oscillate
waveform is normal
is low level?
OK
OK
Check CN403 is solder
NG
Replace X401
Check reset circuit of
and Q405 is OK
U401 is normal
NG
NG
Check Correspondent
component.
OK
OK
Replace U401
Replace PANEL
34
Check Correspondent
component.
AOC 917Sw
8.2.2 Power/Inverter Board

1.) No power
Check CN902 pin4, 5 = 12V
NG
Check AC line volt 110V or 220V
OK
NG
Check AC input
Check the voltage of C905 (+)

NG
OK
Check bridge rectified circuit and F901 circuit
Check start voltage for the pin8 of IC901

NG
OK
Check R932, R933 and Change IC901
Check the auxiliary voltage is bigger than

10V and smaller than 20V
OK
NG
1) Check IC901
2) Check R909, D901 circuit
Check IC901 pin6 PWM wave
OK
NG
Check IC901
Check IC903, IC904, Q901, ZD921, ZD922, D915, D916
35
AOC 917Sw
2.) W / LED, No Backlight

Check CN902 pin4, 5 = 12V
OK
NG
Check adapter or MB
Check ON/OFF signal

OK
NG
Check Interface board
Check IC801 PIN12=12V
OK
NG
Change Q808
Check IC801 PIN10, 9 have the output of square wave at short

NG
OK
Change IC801
Check Q802, Q803 PIN5, 6, 7, 8 have the output of square wave at short time.
NG
OK
Check Q801, Q804, Q811, Q812, Q802, Q803
Check the output of T801, T802

OK
NG
Change T801, T802
Check connecter & lamp
36
AOC 917Sw
8.2.3 Key Board
OSD is unstable or not working
N
Connect Key Pad Board
Is Key Pad Board connecting normally?
Y
N
Is Button Switch normally?
Replace Button Switch
Y
N
Is Key Pad Board normally?
Check Main Board
37
Replace Key Pad Board
AOC 917Sw
9. White- Balance, Luminance Adjustment

Approximately 30 minutes should be allowed for warm up before proceeding white balance adjustment.
Before started adjust white balance , please set the Chroma-7120 MEM Channel 3 to Warm (6500K)
color, MEM Channel 4 to Normal (7300K) color, MEM Channel 9 to Cool (9300K) color , and MEM
Channel 10 to sRGB color ( our Warm color parameter is x = 313 30, y = 329 30, Y=230cd/m2(typ);
Normal color parameter is x = 301 30, y = 317 30, Y=200cd/m2 (typ); Cool color parameter is
x = 283 30, y = 297 30, Y=180cd/m2 (typ); sRGB color parameter is x = 313 20, y = 329 20,
Y= 230cd/m2)
How to setting MEM channel you can reference to chroma 7120 user guide or simple
use SC key and
NEXT Key to modify xyY value and use ID key to modify the TEXT description Following is the procedure
to do white-balance adjust .
2. Setting the color temp. you want
A. MEM.CHANNEL 3 (Warm color):
Warm color temp. parameter is x = 313 30, y = 329 30, Y=230cd/ m2(typ)
B. MEM.CHANNEL 4 (Normal color):
Normal color temp. parameter is x = 301 30, y = 317 30, Y=200cd/ m2(typ)
C. MEM.CHANNEL 9(Cool color):
Cool color temp. parameter is x = 283 30, y = 297 30, Y=180cd/m2 (typ)
D. MEM.CHANNEL 10 (sRGB color):
sRGB color temp. parameter is x = 313 30, y = 329 30, Y= 230cd/m2
3. Into Factory mode of AOC 917Sw:
Press the MENU button, pull out the power cord, and then plug the power cord. Then the factory OSD will be at the
left top of the panel.
4. Bias adjustment:
Set the Contrast
to 50; Adjust the Brightness
to 90.
5. Gain adjustment:
Move cursor to -F- and press MENU key
A. Adjust Warm (6500K) color-temperature
1. Switch the chroma-7120 to RGB-Mode (with press MODE button)
2. Switch the MEM.channel to Channel 3 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 313 30, y = 329 30, Y=230cd/m2 (typ)
4. Adjust the RED on factory window until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory window until chroma 7120 indicator reachedthe value G=100
6. Adjust the BLUE on factory window until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4,5,6) until chroma 7120 RGB value meet the tolerance =1002
B. Adjust Normal (7300K) color-temperature
2. Switch the MEM.channel to Channel 4(with up or down arrow on chroma 7120)
38
AOC 917Sw
C. Adjust Cool (9300K) color-temperature
1. Switch the Chroma-7120 to RGB-Mode (with press MODE button)
2. Switch the MEM. Channel to Channel 9 (with up or down arrow on chroma 7120)
5. Adjust the GREEN on factory window until chroma 7120 indicator reached the value G=100
D. Adjust sRGB color-temperature
2. Switch the MEM.channel to Channel 10 (with up or down arrow on chroma 7120)
3. The LCD-indicator on chroma 7120 will show x = 313 30, y = 329 30, Y= 230cd/m2
E. Turn the Power-button off to quit from factory mode.
39
AOC 917Sw
10. Monitor Exploded View
40
AOC 917Sw
11. BOM List

T98SM5NBUWA1NN
Location
Part No.
Description
040G 58162461A
EPA LABEL
044GH600 1
HANDLE 2
050G 600 4
HANDLE 1
052G
1150 C
INSULATING TAPE
052G
1186
SMALL TAPE
052G
1211 A
Conductive Tape 55mm *45mm *0.08mm
052G
1211 B
Conductive Tape 85mm *40mm *0.09mm
052G
2191 A
PAPER TAPE
Remark
052G6019 1
INSULATING TAPE
052G6019 1
INSULATING TAPE
E08902
089G 725CAA DB
D-SUB CABLE
2nd source
E08902
089G 725HAA DB
D-SUB CABLE
2nd source
E08902
089G 725LAA DB
D-SUB CABLE
089G179J30N517
FFC CABLE
E08901
089G404A15N CX
POWER CORD
E08901
089G404A15N IS
POWER CORD
2nd source
E08901
089G404A15N YH
POWER CORD
2nd source
095G8014 6D 39
HARNESS 6P-6P 150MM
0M1G 130 5120
SCREW
0M1G1730 6120
SCREW,42-D020523
0Q1G 330 8120
SCREW 3X8MM 42A9930017/ 42-D002093
705GQ834021
19" LCD STAND BASE ASS'Y
A34G0289ABJ 1B
STAND
A37G0031 1
HINGE
AM1G1740 12 47 CR3
SCREW
Q12G6600 8
PORON FOOT
Q34G0243AED 1B 30
BASE
E750
750GLS90M31ACN
PANEL LTM190M2-L31 8UN(4UZ) FQ SEC
E750
750GLS90M31DCN
PANEL LTM190M2-L31 8UP FQ SEC
2nd source
E750
750GLS90M31PCN
PANEL LTM190M2-L31 8CP FQ SEC
2nd source
A15G0205 S2 5
MAIN FRAME
A33G0173ABJ 1L 32
CABLE CLAMP
A34G0288ABJA4B
REAR COVER(19")
AM1G1740 12 47 CR3
SCREW
CBPC8SM5A2Q2
MAIN BOARD G2904-1-X-X-12-080229
040G 45762412B
CBPC LABEL
033G3802 6
WAFER
CN401
41
AOC 917Sw
CN404
033G3802 9
WAFER 9P RIGHT ANELE PITCH
CN403
033G801930F CH JS
CONNECTOR
C427
067G 3151014KV
EC 105 CAP 100UF M 25V
C426
067G 3151014KV
C423
067G 3151014KV
C421
067G 3151014KV
C410
067G215V100 7R
LOW E.S.R 10UF M 50V
CN101
088G 35315F HD
D-SUB CONN F ATTACHED SCREW
CN101
088G 35315F XH
D-SUB 15PIN VERTICAL CONN WITH SCREW
CN101
088G 35315F XH
D-SUB 15PIN VERTICAL CONN WITH SCREW
X401
093G 22 53 J
14.31818MHZ/32PF/49US
709G2904 QM001
CONSUMPTIVE ASS'Y
055G
ALCOHOL
055G 23524
WELDING FLUX WITHOUT PB
Q55G 100625
TIN STICK_LOW ARGENTUM
U401
056G 562557
IC TSUM1PFR-LF
U404
056G 563 52
IC AP1117D33L-13 TO252-3L DIODES
U102
056G 662 13
IC AZC099-04S SOT23-6L
U103
056G 662 13
IC AZC099-04S SOT23-6L
U402
056G1133 81(WA8MRT9SKQ1)
Q404
057G 417 6
PMBS3906/PHILIPS-SMT(06)
Q406
057G 417 12 T
KEC 2N3904S-RTK/PS
Q410
057G 417 22 T
TRA KN2907AS -60V/-0.6A SOT-23
Q409
057G 417 22 T
TRA KN2907AS -60V/-0.6A SOT-23
Q405
057G 763 1
A03401 SOT23 BY AOS(A1)
R401
061G0402000
RST CHIP MAX 0R05 1/16W
R402
061G0402000
R115
061G0402101
RST CHIPR 100 OHM +-5% 1/16W
R114
061G0402101
R113
061G0402101
R111
061G0402101
R110
061G0402101
R108
061G0402101
R104
061G0402101
R103
061G0402101
R102
061G0402101
R117
061G0402101
R457
061G0402101
R456
061G0402101
R442
061G0402101

42
2nd source
2nd source
2nd source
AOC 917Sw
R420
061G0402101
R413
061G0402101
R412
061G0402101
R411
061G0402101
R405
061G0402101
R118
061G0402102
RST CHIPR 1 KOHM +-5% 1/16W
R441
061G0402102
R439
061G0402103
R437
061G0402103
R433
061G0402103
R421
061G0402103
R417
061G0402103
R408
061G0402103
R407
061G0402103
R406
061G0402103
R404
061G0402103
R121
061G0402103
R120
061G0402103
R436
061G0402104
R414
061G0402121
RST CHIP 120R 1/16W 5%
R410
061G0402121
R409
061G0402203
RST CHIP 20K 1/16W 5%
R105
061G0402222
RST CHIPR 2.2 KOHM +-5% 1/16W
R106
061G0402222
R403
061G0402390 0F
R109
061G0402390 0F
R427
061G0402392
RST CHIP 3.9K 1/16W 5%
R428
061G0402392
RST CHIP 3.9K 1/16W 5%
R435
061G0402472
R440
061G0402472
R107
061G0402750
R112
061G0402750
R116
061G0402750
R101
061G0603000
R434
061G1206331
C432
065G0402104 15
MLCC 0402 0.1UF K 16V X5R
C428
065G0402104 15
C422
065G0402104 15
C420
065G0402104 15
C419
065G0402104 15

43
AOC 917Sw
C417
065G0402104 15
C416
065G0402104 15
C415
065G0402104 15
C414
065G0402104 15
C413
065G0402104 15
C409
065G0402104 15
C407
065G0402104 15
C406
065G0402104 15
C404
065G0402104 15
C403
065G0402104 15
C401
065G0402104 15
C412
065G0402220 31
CHIP 22PF 50V NPO
C411
065G0402220 31
CHIP 22PF 50V NPO
C103
065G0402220 31
CHIP 22PF 50V NPO
C102
065G0402220 31
CHIP 22PF 50V NPO
C408
065G0402224 17
CAP CER 0.22UF -20%-80%
C113
065G0402473 12
CHIP 0.047UF 16V X7R
C110
065G0402473 12
C109
065G0402473 12
C107
065G0402473 12
C106
065G0402473 12
C105
065G0402473 12
C101
065G0402473 12
C104
065G0402509 31
CHIP 5PF 50V NPO
C108
065G0402509 31
CHIP 5PF 50V NPO
C111
065G0402509 31
CHIP 5PF 50V NPO
FB402
071G 56K121 M
CHIP BEAD
FB401
071G 56V301 B
CHIP BEAD FCM2012VF-301T07 BULLWILL
FB101
071G 59K190 B
19 OHM BEAD
FB102
071G 59K190 B
19 OHM BEAD
FB103
071G 59K190 B
19 OHM BEAD
D401
093G 64 33
DIO SIG SM BAV99 (PHSE)R
ZD103
093G 39S 34 T
UDZSNP5.6B ROHM
ZD104
093G 39S 34 T
UDZSNP5.6B ROHM
093G3004 3
SM340A
715G2904 1
MAIN PCB 57X64X1.6MM DS
Q404
057G 417517
TRA LMBT3906LT1G -200MA/-40V SOT-23 LRC
U404
056G 563916
IC LD1117DT33TR DPAK
709G2904 QS001
CONSUMPTIVE ASS'Y
052G
PAPER TAPE
D402
2191 A
44
AOC 917Sw
052G6026 3
MESH PRINTTING PAPER
Q406
057G 417518
TRA LMBT3904LT1G 200MA/40V SOT-23 LRC
ZD103
093G 39S501 T
LUDZS5.6BT1G BY LRC
ZD104
093G 39S501 T
LUDZS5.6BT1G BY LRC
KEPC7QK7
KEY BOARD G2834-A-X-X-1-070809
CN001
033G3802 6H
WAFER 6P RIGHT ANGLE PITCH 2.0
SW005
077G610D 1 NA
TACT SW+LED
SW005
077G610D 1 WB
TACT SW+LED
709G2834 QM001
CONSUMPTIVE ASS'Y
Q002
057G 417 4
Q001
057G 417 4
R002
061G0603000
R004
061G0603102
RST CHIPR 1K OHM +-5% 1/10W
R003
061G0603202
R001
061G0603202
R006
061G0603472
RST CHIPR 4.7K OHM +-5% 1/10W
R005
061G0603472
SW004
077G 605 1 AL GP
SMD SWITCH
SW001
077G 605 1 AL GP
SMD SWITCH
SW002
077G 605 1 AL GP
SMD SWITCH
SW003
077G 605 1 AL GP
SMD SWITCH
ZD006
093G 64 59 SU
ESD MLVS0603M04 0603
ZD007
093G 64 59 SU
ZD008
093G 64 59 SU
709G2834 QS001
CONSUMPTIVE ASS'Y
715G2834 1
KEY BOARD PCB
PWPC942SEE1
POWER BOARD G2538-3-LEG-X-1-070903
040G 45762412B
CBPC LABEL
GND1
009G6005 1
GROUND TERMINAL
CN801
033G8021 2E F
WAFER
CN802
033G8021 2E F
WAFER
CN803
033G8021 2E F
WAFER
CN804
033G8021 2E F
WAFER
CN801
033G8021 2E U
INVERT CONNECTOR
CN802
033G8021 2E U
INVERT CONNECTOR
CN803
033G8021 2E U
INVERT CONNECTOR
CN804
033G8021 2E U
INVERT CONNECTOR
IC903
056G 139 3A
IC PC123Y22FZ0F
IC903
056G 139 5A
TCET1103G
NR901
061G 58080 WT
8 OHM NCT
45
AOC 917Sw
R908
061G152M104 64
100KOHM 5% 2W
R914
061G152M228 64
0.22 OHM 5% 2W
C903
063G 10747410V
0.47UF 275VAC ARCO
C903
063G107K474 6S
CAP X2 0.47UF K 275VAC
C801
065G 6J1006ET
10PF 5% SL 6KV
C811
065G 6J1006ET
10PF 5% SL 6KV
C901
065G305M1022BP
Y2 1000PF M 250VAC Y5P
C902
065G305M1022BP
Y2 1000PF M 250VAC Y5P
C921
065G306M4722BP
4700PF +-20% 400VAC
C905
067G 40Z10115K
CAP 105 100UF M 450V
C803
067G215D4714KV
E.C 105 CAP 470UF M 25V ED SERIES
C802
067G215D4714KV
C922
067G215D4714KV
C918
067G215D6814KV
CAP 105 680UF M 25V
C917
067G215D6814KV
CAP 105 680UF M 25V
C918
067G215D6814KV
CAP 105 680UF M 25V
C917
067G215D6814KV
CAP 105 680UF M 25V
C939
067G215S1024KV
EC 105 CAP 1000UF M 25V
C915
067G215S4713KV
C803
067G215Y4714HV
C802
067G215Y4714HV
L902
073G 174 65 H
LINE FILTER
L902
073G 174 65 LS
LINE FILTER BY LISHIN
L901
073G 174 76 H
FILTER
L901
073G 174 76 V
LINE FILTER 4MH MIN
L901
073G 174 76 YS
CHOKE COIL
L903
073G 253 91 V1
CHOKE COIL 1.1UH
L904
073G 253 91 V1
CHOKE COIL 1.1UH
L904
073G 253191 H
IND CHOKE 1.1UH DADON
L903
073G 253191 H
IND CHOKE 1.1UH DADON
L904
073G 253191 YS
CHOKE COIL 1.1UH YS04110055
L903
073G 253191 YS
CHOKE COIL 1.1UH YS04110055
T901
080GL19T 23 N
XFMR POWER 510UH YUVA
T901
080GL19T 23 YS
X'FMR 510UH YS04160061
T801
080GL19T 24 H
XFMR INVERTER 740MH DADON
T802
080GL19T 24 H
XFMR INVERTER 740MH DADON
T802
080GL19T 24 DN
XFMR INVERTER 740MH DARFON
T801
080GL19T 24 DN
XFMR INVERTER 740MH DARFON
T801
080GL19T 24 YS
X'FMR 740MH YS04170157
T802
080GL19T 24 YS
X'FMR 740MH YS04170157

46
AOC 917Sw
CN901
087G 501 37 S
AC INLET ST-01DG-B2K-K
BD901
093G 50460 28
BRIDGE DIODE KBP208G LITEON
BD901
093G 50460510
2KBP08M 2A 800V
D907
093G3006 1 1
31DQ06FC3 NIHON INTER
CN902
095G8014 9D 57
HARNESS 9P-9P 210MM
CN902
095G8014 9X 57
WIRE HARNESS 9P(SCN)-9P(PH) 210MM
705G 193 57 01
Q901 ASS'Y
Q901
057G 667 21
STP10NK70ZFP
Q901
057G 667 22
FQPF8N80C
090G6263 1
HEAT SINK
0M1G1730 8120
SCREW
705G 193 93 01
D906 ASS'Y
D906
093G 60218
SB10100FCT
D906
093G 60267
SP10100
0M1G1730 10120
SCREW 42A9930016
Q90G6274 2
HEAT SINK
705GQ851002
OIL FOR DISAPPEAR ASS'Y
709G2538 QM001
CONSUMPTIVE ASS'Y
055G
ALCOHOL
055G 23524
WELDING FLUX WITHOUT PB
Q55G 100625
TIN STICK_LOW ARGENTUM
IC801
056G 379 22
IC TL494IDR SOIC-16
IC901
056G 379 71
IC TEA1530AT/N2 SO-8 NXP
Q902
057G 417 4
Q811
057G 417 4
Q807
057G 417 4
Q806
057G 417 4
Q801
057G 417 4
Q812
057G 417 6
Q804
057G 417 6
Q811
057G 417 12 T
KEC 2N3904S-RTK/PS
Q807
057G 417 12 T
KEC 2N3904S-RTK/PS
Q806
057G 417 12 T
KEC 2N3904S-RTK/PS
Q801
057G 417 12 T
KEC 2N3904S-RTK/PS
Q804
057G 417 16 T
MMBT2907
Q812
057G 417 16 T
MMBT2907
Q802
057G 600 55
P5506 HVG SO-8
Q803
057G 600 55
P5506 HVG SO-8
Q809
057G 758 1
2N7002ESOT23 SILICONIX
Q809
057G 759 2
RK7002FD5T116 SOT-23 BY ROHM

47
AOC 917Sw
Q810
057G 759 2
RK7002FD5T116 SOT-23 BY ROHM
Q808
057G 760 4A
DTA144WN3/S SOT-23
Q808
057G 760 4B
PDTA144WK SOT346
Q805
057G 760 5A
DTC 144WN3/S SOT-23
Q805
057G 760 5B
PDTC144WK SOT346
Q802
057G 763 14
AM9945N
Q803
057G 763 14
AM9945N
R942
061G0603100 1F
R925
061G0603100 1F
R826
061G0603100 1F
R824
061G0603100 1F
R822
061G0603100 1F
R821
061G0603100 1F
R818
061G0603100 1F
R812
061G0603100 1F
R809
061G0603100 1F
R817
061G0603100 2F
R828
061G0603100 2F
R832
061G0603100 2F
R833
061G0603100 2F
R834
061G0603100 2F
R808
061G0603100 2F
R813
061G0603100 2F
R926
061G0603100 2F
R827
061G0603102
R862
061G0603105
RST CHIPR 1M OHM +-5% 1/10W
R835
061G0603105
R803
061G0603105
R816
061G0603150 1F
R815
061G0603150 1F
R814
061G0603150 1F
R801
061G0603150 1F
R924
061G0603152
R831
061G0603240 1F
R930
061G0603240 1F
R811
061G0603240 1F
R940
061G0603330 2F
RST CHIPR 33K
R927
061G0603360 1F
R819
061G0603362
R823
061G0603362

48
OHM +-1% 1/10W
AOC 917Sw
R861
061G0603390 3F
R807
061G0603470 2F
R820
061G0603470 2F
R806
061G0603680 2F
RST CHIPR 68K
OHM +-1% 1/10W
R854
061G0603680 2F
RST CHIPR 68K
OHM +-1% 1/10W
R853
061G0603680 2F
RST CHIPR 68K
OHM +-1% 1/10W
R841
061G0603680 2F
RST CHIPR 68K
OHM +-1% 1/10W
R851
061G0603910 1F
R851
061G0603912
R850
061G0805000
R839
061G0805000
R804
061G0805101
1ST CHIPR 100
OHM +-5% 1/8W
R929
061G0805102
RST CHIPR 1K
OHM +-5% 1/8W
R917
061G0805102
RST CHIPR 1K
OHM +-5% 1/8W
R911
061G0805102
RST CHIPR 1K
OHM +-5% 1/8W
R938
061G0805103
R916
061G0805152
R825
061G0805220
R829
061G0805220
R912
061G0805220 2F
R837
061G0805473
R810
061G0805510 2F
R915
061G0805753
CHIP 75KOHM 1/10W
R931
061G0805822
JR802
061G1206000
JR804
061G1206000
JR805
061G1206000
JR807
061G1206000
JR808
061G1206000
JR809
061G1206000
JR801
061G1206000
JR803
061G1206000
F801
061G1206000 4
F902
061G1206000 4
R967
061G1206000 4
R909
061G1206100
RST CHIPR 10
OHM +-5% 1/4W
R910
061G1206100
RST CHIPR 10
OHM +-5% 1/4W
R962
061G1206101
R961
061G1206101
R935
061G1206101

49
AOC 917Sw
R920
061G1206101
R919
061G1206101
R918
061G1206101
R921
061G1206102
R922
061G1206102
R923
061G1206102
R928
061G1206102
R855
061G1206150
R857
061G1206150
R856
061G1206150
R858
061G1206150
R901
061G1206684
R902
061G1206684
R903
061G1206684
C842
065G0603103 12
CHIP 0.01UF 16V X7R
C924
065G0603103 12
CHIP 0.01UF 16V X7R
C807
065G0603104 22
CAP CHIP 0603 0.1UF K 25V X7R
C821
065G0603104 22
C825
065G0603104 22
C834
065G0603104 22
C815
065G0603222 22
CHIP 2200PF 25V X7R
C816
065G0603222 22
CHIP 2200PF 25V X7R
C819
065G0603222 22
CHIP 2200PF 25V X7R
C823
065G0603222 22
CHIP 2200PF 25V X7R
C910
065G0805102 32
CHIP 1000P 50VX7R 0805
C931
065G0805104 32
C930
065G0805104 32
C916
065G0805104 32
C907
065G0805104 32
C824
065G0805104 32
C805
065G0805104 32
C911
065G080510522K
CAP CHIP 0805 1UF K 25V X7R
C822
065G080510522K
CAP CHIP 0805 1UF K 25V X7R
C928
065G0805122 31
CHIP CAP 0805 1200PF J 50V NPO
C841
065G0805152 31
1.5NF/50V
C838
065G0805152 31
1.5NF/50V
C840
065G0805152 31
1.5NF/50V
C839
065G0805152 31
1.5NF/50V
C820
065G080522131G
CAP CHIP 0805 220PF G 50V NPO
C909
065G0805224 32
0.22UF,K,50V,X7R
50
AOC 917Sw
C845
065G0805225 12
C912
065G1206102 72
CAP CHIP 1206 1000PF K 500V X7R
C929
065G1206102 72
CAP CHIP 1206 1000PF K 500V X7R
D801
093G 64 33
D802
093G 64 33
D803
093G 64 33
D804
093G 64 33
D805
093G 64 38 D
DIODE BAW56 DIODES
D808
093G 64 38 D
DIODE BAW56 DIODES
D903
093G 64 38 P
BAW56
D809
093G 6432S
1N4148W
D916
093G 6432S
1N4148W
D915
093G 6432S
1N4148W
D817
093G 6432S
1N4148W
D814
093G 6432S
1N4148W
D806
093G 6432S
1N4148W
D801
093G 6433P
BAV99
D802
093G 6433P
BAV99
D803
093G 6433P
BAV99
D804
093G 6433P
BAV99
ZD922
093G 39S 25 T
RLZ5.1B LLDS
ZD921
093G 39S 61 T
DIODE RLZ16B ROHM
ZD902
093G 39S 61 T
DIODE RLZ16B ROHM
CN901
006G 31500
EYELET
NR901
006G 31502
1.5MM RIVET
T901
006G 31502
1.5MM RIVET
IC904
056G 158 4 T
H431BA
IC904
056G 158 12
KIA431A-AT/P TO-92
C906
065G 2K152 1T6921
1.5NF/2KV Y5P +-10%
C938
065G 2K152 1T6921
1.5NF/2KV Y5P +-10%
C908
067G215Y2207KT
CAP 105 22UF M 50V KINGNICHI
FB901
071G 55 29
FERRITE BEAD
F901
084G 55 1W
FUSE 4A 250V WICKMANN
D901
093G 6038P52T
PS102R
D900
093G1100 1152T
DIODE PR1007R 1A/1000V DO-41
J801
095G 90 23
JUMPER WIRE
J802
095G 90 23
JUMPER WIRE
J803
095G 90 23
JUMPER WIRE
J804
095G 90 23
JUMPER WIRE
J805
095G 90 23
JUMPER WIRE
51
AOC 917Sw
J806
095G 90 23
JUMPER WIRE
J807
095G 90 23
JUMPER WIRE
J817
095G 90 23
JUMPER WIRE
J815
095G 90 23
JUMPER WIRE
J906
095G 90 23
JUMPER WIRE
J904
095G 90 23
JUMPER WIRE
J903
095G 90 23
JUMPER WIRE
J902
095G 90 23
JUMPER WIRE
J901
095G 90 23
JUMPER WIRE
J816
095G 90 23
JUMPER WIRE
J814
095G 90 23
JUMPER WIRE
J813
095G 90 23
JUMPER WIRE
J812
095G 90 23
JUMPER WIRE
J811
095G 90 23
JUMPER WIRE
J810
095G 90 23
JUMPER WIRE
J809
095G 90 23
JUMPER WIRE
J808
095G 90 23
JUMPER WIRE
715G2538 5
POWER-PCB FR-1 160*124MM SS
709G2538 QA001
CONSUMPTIVE ASS'Y
095G 90 23
JUMPER WIRE
709G2538 QS001
CONSUMPTIVE ASS'Y
052G
PAPER TAPE
J905
2191 A
R932
061G1206682
R933
061G1206682
D902
093G 6432S
1N4148W
093G 39S 61 T
DIODE RLZ16B ROHM
R937
061G1206221
L902
S73G17465VW
LINE FILTER ASS'Y
T901
S80GL19T23V
TRANSFORMER ASS'Y
T801
S80GL19T24V
TRANSFORMER ASS'Y
Q34FPE19P07
CASE EEL19
071FPE19301 03
FP2 EEL 19 19T24V
S80GL19T24V
TRANSFORMER ASS'Y
Q34FPE19P07
CASE EEL19
071FPE19301 03
FP2 EEL 19 19T24V
ZD903
T802
Q20G6036 1
30
FUNCTION-KEY-COAT
Q20G6046 1
30
POWER_KEY
Q33G0164 1 2C
POWER-KEY
Q34G0242AEDB1B
BEZEL (19")
Q40G000260811A
BASIC LABEL
52
AOC 917Sw
Q40G000262427A
POP LABEL
Q41G780B61514A
917SW 08OSD QSG
Q44G9141101
EPS
Q44G9141201
EPS
Q44G9141615 7A
19 LCD AOC CARTON
Q45G 88606 16
PE BAG FOR CLAMP
Q45G 88607 72
PE BAG
Q50G
4 10
TIE
Q52G
1185 99
BIG CARTON TAPE FOR AOC
041G780061554A
Q45G 76 28 RN
SERVICE CENTER LIST

R
PE BAG MANUAL
Q70G900261527A
CD MANUAL
040G 58162435A
P/N LABEL FOR MANUAL PE BAG
040G 581689 4A
BARCODE LABEL FOR 1
Q40G 19N61586A
RATING LABEL
53
AOC 917Sw
12. Different Parts List

Diversity of T9RSM5NLUWCKNZ Compared with T98SM5NBUWA1NN
Location
U402
SMTCR-U402
Part No.
Description
089G412A18NIS3
POWER CORD/32E1818058
756GQ8CB AA012
MAIN BOARD-CBPCRM5A3Q2
056G1133 81
100GAMS9000N11
MCU ASS'Y-056G1133 81
Q26G 800504 2
BARCODE LABEL FOR 3
Q40G 19N61576A
RATING LABEL
Q40G0002634 1A
C-TICK LABEL
Q44G9141615 4A
19LCD AOC CARTON
Q36G 600517
DUSTER CLOTH
Q41G780A61549C
WARRANTY CARD
Diversity of T9RSM5NPUWA5NN Compared with T98SM5NBUWA1NN

Location
Part No.
Description
E08901
089G402A15N IS
POWER CORD
E08901
089G402A15N YH
POWER CORD
756GQ8CB AA012
056G1133 81
100GAMS9000N11
MCU ASS'Y-056G1133 81
Q26G 800504 2
BARCODE LABEL FOR 3
Q40G 19N61580A
RATING LABEL
Q44G9094101
EPS
Q44G9094201
EPS
Q44G9094615 3A
19W AOC CARTON
041G780061513B
INPUT NOT SUPPORT CARD
041G780061518B
EASE PROGRAM
Q41G7800615A69
MEXICO CENTER LIST
Q41G7800615B93
WARRANTY CARD FOR MEXICO
U402
SMTCR-U402
Q45G 76 28 C
040G 459690 5A
PE BAG FOR MANUAL

CARTON LABEL
54
Remark
2nd source
AOC 917Sw
Diversity of T9RSM5NPUWA5NG Compared with T98SM5NBUWA1NN

Location
Part No.
Description
E08907
089G179J30N 9
FFC CABLE
E08901
089G402A15N IS
POWER CORD
E08901
089G402A15N YH
POWER CORD
750GLS90M31DCB
PANEL LTM190M2-L31 BUP SEC
756GQ8CB AA012
056G1133 81
100GAMS9000N11
MCU ASS'Y -056G1133 81
Q26G 800504 2
BARCODE LABEL FOR 3
Q44G9094101
EPS
Q44G9094201
EPS
Q44G9094615 3A
19W AOC CARTON
S89G179T30N9
FFC CABLE
033F303FH10BK3
F1010HA-30P-BK
041G780061513B
041G780061518B
EASE PROGRAM
U402
SMTCR-U402
E08907
Q45G 76 28 C
Remark
2nd source
PE BAG FOR MANUAL
040G 459690 5A
CARTON LABEL
Q40G 19N61580A
RATING LABEL
Diversity of T9RSM5NQUWA2NN Compared with T98SM5NBUWA1NN

Location
Part No.
Description
E08901
089G402A15N IS
POWER CORD
E08901
089G402A15N YH
POWER CORD
756GQ8CB AA012
056G1133 81
100GAMS9000N11
MCU ASS'Y-056G1133 81
Q40G 19N61583A
RATING LABEL
Q44G9094101
EPS
Q44G9094201
EPS
Q44G9094615 2C
19 LCD AOC CTN
041G780061513B
041G780061518B
EASE PROGRAM
041G780061545B
WARRANTY BOOKLET
Q41G780A61510A
WARRANTY CARD SA(SPANISH)
Q41G780A61511B
SA CENTER LIST
U402
SMTCR-U402
Q45G 76 28 C
Q26G 800504 2
PE BAG FOR MANUAL

BARCODE LABEL FOR 3
55
Remark
2nd source
AOC 917Sw
Diversity of T9RSM5NKUWA2NN Compared with T98SM5NBUWA1NN

Location
Part No.
Description
E08901
089G402A15N IS
POWER CORD
E08901
089G402A15N YH
POWER CORD
756GQ8CB AA012
056G1133 81
100GAMS9000N11
MCU ASS'Y-056G1133 81
Q40G 19N61583A
RATING LABEL
Q44G9094101
EPS
Q44G9094201
EPS
Q44G909461510A
19 LCD AOC CARTON
041G780061513B
Q41G780A61592A
NA WARRANTY CARD
Q41G780A61593A
EASE CARD
U402
SMTCR-U402
Q45G 76 28 C
Q26G 800504 2
Remark
2nd source
PE BAG FOR MANUAL

BARCODE LABEL FOR 3

Location
U402
SMTCR-U402
Part No.
Description
089G416A15N IS
POWER CORD I-SHENG
756GQ8CB AA012
056G1133 81
100GAMS9000N11
MCU ASS'Y-056G1133 81
Q40G 19N61583A
RATING LABEL
Q44G9094101
EPS
Q44G9094201
EPS
Q44G9094615 2C
19 LCD AOC CTN
041G780061513B
041G780061518B
EASE PROGRAM
041G780061545B
WARRANTY BOOKLET
Q41G780A61510A
Q41G780A61511B
SA CENTER LIST
Q45G 76 28 C
Q26G 800504 2
PE BAG FOR MANUAL

BARCODE LABEL FOR 3
56
Remark
AOC 917Sw

Location
U402
SMTCR-U402
Part No.
Description
089G408A15N IS
POWER CORD(WALL-OUT FOR ITALY)
756GQ8CB AA012
056G1133 81
100GAMS9000N11
MCU ASS'Y-056G1133 81
Q40G 19N61583A
RATING LABEL
Q44G9094101
EPS
Q44G9094201
EPS
Q44G9094615 2C
19 LCD AOC CTN
041G780061513B
041G780061518B
EASE PROGRAM
041G780061545B
WARRANTY BOOKLET
Q41G780A61510A
Q41G780A61511B
SA CENTER LIST
Q45G 76 28 C
Q26G 800504 2
PE BAG FOR MANUAL

BARCODE LABEL FOR 3
57

Aoc 917sw Tsum1pfr

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Aoc 917sw Tsum1pfr

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aoc 917sw Tsum1pfr

Uploaded by

Copyright:

Available Formats

19" LCD Color Monitor

5.2.Electrical Block Diagram...............................16

Important Safety Notice.3

2. LCD Monitor Description.......5

3.1. General Instructions..............................................6

3.2. Control Buttons........................................................6

3.3. OSD Menu.............................................................7

4.1. Input Signal Connector...............................9

8.1.Equipments and Tools Requirement...............31

4.2. Power Supply Requirements....................................9

4.3. Factory Preset Display Modes.........................10

9. White-Balance, Luminance adjustment................38

4.4. Panel Specification...10

10. Monitor Exploded View...................................40

5.1. Software Flow Chart.....14

12.Different Parts List..................54

19" LCD Color Monitor

TPV Model Name

19" LCD Color Monitor

Important Safety Notice

19" LCD Color Monitor

TFT Color LCD

Viewable Image Size

Horizontal scan range

Horizontal scan Size(Maximum)

Vertical scan range

Vertical scan Size(Maximum)

Optimal preset resolution

1440 x 900 (60 Hz)

Highest preset resolution

1440 x 900 (60 Hz)

Plug & Play

Input Video Signal

Analog: 0.7Vp-p(standard), 75 OHM, Positive

Active < 37W

15-pin Mini D-Sub

Signal Cable Type

Dimensions & Weight:

Height (with base)

Weight (monitor only)

Weight (with packaging)

10% to 85% (non-condensing)

0~ 3000m (0~ 10000 ft )

0~ 5000m (0~ 15000 ft )

19" LCD Color Monitor

2. LCD Monitor Description

Monitor Block Diagram

Flat Panel and

19" LCD Color Monitor

The power cord should be connected.

3.2 Control Buttons

1. Eco Mode / Up 2. Exit / - 3. Menu / + 4. Auto / Down 5. Power on/off

3.2.2 Key Function

to change the settings of the selected function. Press

to select another function in

to adjust volume ( Only for the models with speakers).

19" LCD Color Monitor

OSD Function Introduction