Viola 24K 2
Viola 24K 2
Viola 24K 2
TEST REPORT
IEC 60335-2-40 / EN 60335-2-40
Safety of household and similar electrical appliances
Part 2: Particular requirements for electrical heat pumps, air conditioners and
dehumidifier
Report Reference No...................... :
GZ12100571-1R3
Date of issue..................................... :
139
CB Testing Laboratory................... :
Address ............................................ :
Applicants name............................ :
Address ............................................ :
Test specification:
Standard ........................................... :
LVD
N/A
IECEN60335_2_40B
VDE
Dated 2006-11
Copyright 2006 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from
the reader's interpretation of the reproduced material due to its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the CB Scheme
procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended
to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
If this Test Report Form is used by non-CCA members, the CIG logo and the reference to the CCA Procedure shall be
removed.
This report is not valid as a CCA Test Report unless signed by an approved CCA Testing Laboratory and
appended to a CCA Test Certificate issued by an NCB in accordance with CCA
Page 3 of 139
Testing location:
Original:
Full tests were conducted on model GWH24RDK3DNA3C.
Modification 1:
Test of clause 10 was conducted on model
GWH24RD-K3DNA8C.
Modification 2:
After review, no test was needed.
Modification 3:
After review, no test was needed.
The product was tested complies with the
requirements of these standards.
Summary of compliance with National Differences: N/A
Copy of marking plate:
Page 4 of 139
Page 5 of 139
Page 6 of 139
General remarks:
Page 7 of 139
Report. No.: GZ12100571-1R3
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
(See Enclosure #) refers to additional information appended to the report.
(See appended table) refers to a table appended to the report.
Note: EN Group Differences together with National Differences and Special National Conditions, if
any, are in the Appendix to the main body of this TRF.
Throughout this report a comma is used as the decimal separator.
When determining the test result, measurement uncertainty has been considered.
Note: The Requirements of IEC 60335-2-40 and EN 60335-2-40 in clause 15 are by identical content
different numbered. For better handling the column Clause contains an additional Information
IEC or EN.
This report is for the exclusive use of Interteks Client and is provided pursuant to the agreement between
Intertek and its Client. Interteks responsibility and liability are limited to the terms and conditions of the
agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the
agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is
authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek
name or one of its marks for the sale or advertisement of the tested material, product or service must first
be approved in writing by Intertek. The observations and test results in this report are relevant only to the
sample tested. This report by itself does not imply that the material, product, or service is or has ever been
under an Intertek certification program.
The test report only allows to be revised only within the report defined retention period unless standard or
regulation was withdrawn or invalid.
General product information:
Manufacturing Site: Gree Electric Appliances, Inc. of Zhuhai
Jinji West Road, Qianshan, Zhuhai, Guangdong 519070, P.R. China
Original:
The appliances are split type, inverter, wall mounted air-conditioner with cooling and heating operate mode
intend for household use. The indoor unit must be installed at the height of 2,5m above the floor of indoor
and outdoor unit must be installed at outdoor side.
The power supplied by indoor unit via a supply lead permanently connected to fixed wiring, and the indoor
unit and outdoor unit via interconnection cords for communication of power supply and signal.
Model differences:
GWH24RD-K3DNA2C is the same as GWH24RD-K3DNA3C except front panel of indoor unit.
Model list:
Model name
Indoor unit
GWH24RD-K3DNA3C
GWH24RD-K3DNA3C/I
GWH24RD-K3DNA2C
GWH24RD-K3DNA2C/I
Outdoor unit
GWH24RD-K3DNA3C/O
Modification 1:
This test report replaces the original test report GZ12100571-1, dated on December 19, 2012, it is issued
for the following changes:
1. Changed the Heating Rated Input from 2700W to 4000W on the nameplate of GWH24RDK3DNA3C/O for models GWH24RD-K3DNA2C and GWH24RD-K3DNA3C.
2.
Page 8 of 139
Report. No.: GZ12100571-1R3
The new model GWH24RD-K3DBA5E can be operated at the lower ambient of -20C than the original
model GWH24RD-K3DNA3C, and the new model employing heating element for chassis at outdoor
unit, refer to attach photo for details.
4. Added some components such as main board M846F2UEJ, interconnection cord and terminal blocks
for the new models, see table 24.1 for details, main board M846F2UEJ and M846F2TAJ are the same
as original M846F2TJ except control software that does not affect the safety of product.
Model list:
Model name
Indoor unit
Outdoor unit
3.
GWH24RD-K3DNA6C
GWH24RD-K3DNA6C/I
GWH24RD-K3DNA3C/O
GWH24RD-K3DNA8C
GWH24RD-K3DNA8C/I
GWH24RD-K3DNA8C/O
GWH24RD-K3DBA5E
GWH24RD-K3DBA5E/I
GWH24RD-K3DBA5E/O
Modification 2:
This test report replaces the original test report GZ12100571-1R1, dated on March 20, 2013, it is issued for
the following changes:
1. Added a new model GWH24RD-K3DBE1E which is identical to GWH24RD-K3DBA5E except for front
panel of indoor unit.
2. Corrected the weight of outdoor unit on the nameplate for model GWH24RD-K3DBA5E from 68kg to
63kg.
Model list:
Model name
Indoor unit
Outdoor unit
GWH24RD-K3DBE1E
GWH24RD-K3DBE1E/I
GWH24RD-K3DBA5E/O
Modification 3:
This test report replaces the original test report GZ12100571-1R2, dated on April 28, 2013, it is issued for
the following changes:
1. Added 2 new models GWH24RD-K3DNA5C and GWH24RD-K3DBA3E which are identical to
GWH24RD-K3DNA8C and GWH24RD-K3DBA5E respectively except for front panel of indoor unit.
2. Added alternative relays and Y capacitor, refer to Table 24.1 for details.
Model list:
Model name
Indoor unit
Outdoor unit
GWH24RD-K3DNA5C
GWH24RD-K3DBA3E
GWH24RD-K3DNA5C/I
GWH24RD-K3DBA3E/I
GWH24RD-K3DNA8C/O
GWH24RD-K3DBA5E/O
Page 9 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
5.3
N/A
5.6
5.10
5.14
5.101
N/A
QXAS-D23zX090B
P
N/A
Page 10 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
5.102
CLASSIFICATION
6.1
6.2
Result
Verdict
P
Class I
P
P
N/A
N/A
6.101
7.1
N/A
Class I appliance
N/A
N/A
See page 2
Page 11 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Refrigerant identification
(IEC/EN 60335-2-40)
R410A
Verdict
P
N/A
N/A
Symbol for degree of protection against ingress of IP24 for outdoor unit
water, other than IPX0
(IEC/EN 60335-2-40):
N/A
N/A
The flame symbol and the instruction manual symbol of 7.6 is visible when a
flammable refrigerant is employed and the following conditions exist:
(IEC/EN 60335-2-40/A1)
N/A
N/A
N/A
N/A
N/A
N/A
Page 12 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
7.2
7.3
N/A
The maximum allowable pressure for the lowpressure side and the high-pressure side is
marked on the product.
(IEC/EN 60335-2-40/A1)
N/A
N/A
N/A
N/A
N/A
7.4
N/A
7.5
N/A
the power input is related to the mean value of the Replaced by IEC/EN 60335rated voltage range
1/A2:2006, See appendix
Relation between marking for upper and lower
limits of rated power input or rated current and
voltage is clear
7.6
--N/A
P
N/A
Page 13 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
7.7
7.8
Except for type Z attachment, terminals for connection to the supply mains
indicated as follows:
N/A
7.9
7.10
N/A
7.11
7.12
7.12.1
N/A
N/A
(IEC/EN 60335-2-40):
N/A
P
Page 14 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
N/A
N/A
N/A
N/A
7.12.2
7.12.3
N/A
7.12.4
- dimensions of space
N/A
N/A
N/A
N/A
N/A
N/A
Page 15 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
N/A
N/A
7.12.6
N/A
7.12.7
7.12.8
N/A
N/A
N/A
7.12.5
7.13
In English
7.14
7.15
N/A
N/A
Page 16 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
7.101
N/A
N/A
7.102
N/A
8.1
8.1.1
N/A
8.1.2
N/A
8.1.3
N/A
8.1.4
N/A
N/A
N/A
Page 17 of 139
IEC / EN 60335-2-40
Clause
8.1.5
8.2
Requirement Test
Result
Verdict
N/A
N/A
N/A
N/A
- built-in appliances
N/A
- fixed appliances
Neither bare live parts nor basic isolated live parts are touchable with the test finger
through openings in the enclosure. The lead wires of plasma ion generator have
double insulation.
--
Internal basic insulation wires are well-fixed and supplementary insulation from
accessible screw.
Only possible to touch parts separated from live
parts by double or reinforced insulation
Not applicable
N/A
(IEC/EN 60335-2-40)
10
10.1
10.2
N/A
Page 18 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
11
HEATING
11.1
Result
Verdict
(IEC/EN 60335-2-40):
11.2
N/A
N/A
(IEC/EN 60335-2-40):
N/A
- static pressures
N/A
- adjustable limit controls set at the maximum cutout setting and the minimum differential
N/A
N/A
11.2.1
N/A
11.2.2
N/A
11.3
11.4
11.5
11.6
P
1,06x240=254,4V
N/A
N/A
N/A
Page 19 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
if needed
Result
Verdict
(IEC/EN 60335-2-40)
11.7
11.8
N/A
N/A
N/A
N/A
N/A
13
13.1
11.9
13.2
N/A
Page 20 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
13.3
Result
14
15.1
TRANSIENT OVERVOLTAGES
N/A
15
Verdict
N/A
N/A
N/A
MOISTURE RESISTANCE
N/A
N/A
Page 21 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
15.1.2
15.2
15.1.1
Verdict
P
N/A
N/A
(IEC) Tests in accordance with IEC 60529 in appliances IPX4 for outdoor unit
other than IPX0, as specified
(EN)
(IEC/EN 60335-2-40)
N/A
N/A
N/A
N/A
(EN 60335-2-40)
N/A
N/A
N/A
N/A
Page 22 of 139
IEC / EN 60335-2-40
Clause
15.3
15.2
Requirement Test
Result
Verdict
P
N/A
16
16.1
16.2
16.3
N/A
17
18
N/A
N/A
N/A
N/A
N/A
ENDURANCE
N/A
Page 23 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
19
ABNORMAL OPERATION
19.1
Temperature of the windings does not exceed the (see appended table of 19.2)
values shown in the table ; temperature (C)
(IEC/EN 60335-2-40)........:
19.2
19.3
Result
Verdict
N/A
19.4
19.5
Page 24 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
(IEC/EN 60335-2-40)
Disconnection of the motor common to both the
outdoor and the indoor heat exchangers when
reaching steady conditions
(IEC/EN 60335-2-40)
N/A
19.6
N/A
19.7
19.8
N/A
19.9
N/A
19.10
19.10.1
N/A
N/A
N/A
N/A
N/A
19.10.101
N/A
Page 25 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
(IEC 60335-2-40/A2)
19.11
19.11.1
19.11.2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Fault conditions applied one at a time, the appliance operated under conditions
specified in Cl.11, but supplied at rated voltage, the duration of the tests as
specified
(IEC/EN 60335-2-40):
N/A
Page 26 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
N/A
N/A
In each case, the test is ended if a non-selfresetting interruption of the supply occurs within
the appliance. (IEC/EN 60335-1/A1)
N/A
(IEC/EN 60335-2-40) :
19.11.4
N/A
N/A
PTCs, NTCs and VDRs resistors not shortcircuited if used as specified by manufacturer
(IEC/EN 60335-2-40)
N/A
N/A
Page 27 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
19.11.4.1
N/A
19.11.4.2
N/A
19.11.4.3
N/A
19.11.4.4
N/A
N/A
N/A
19.11.4.5
N/A
19.11.4.6
N/A
Page 28 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
19.12
N/A
N/A
19.13
N/A
19.13
Replaced by EN 60335-2-40
---
---
---
---
19.14
19.101
N/A
Page 29 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
(IEC 60335-2-40/A2)
During the test the temperature shall not exceed
150 C but an overshoot of 25 C is permitted
during the first hour.
(IEC 60335-2-40/A2)
N/A
20
20.1
Adequate stability
N/A
N/A
N/A
N/A
20.2
Access to fan impeller of the outdoor unit is prevented by a grill, which is not
removable without using a tool. The test finger can not touch the fan impeller with a
force not more than 5N.
--
N/A
21
MECHANICAL STRENGTH
21.1
Page 30 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
21.2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Page 31 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
22
CONSTRUCTION
22.1
22.2
N/A
N/A
- an appliance inlet
N/A
---
N/A
N/A
N/A
N/A
22.4
N/A
22.5
---
---
Page 32 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
22.6
N/A
22.7
22.8
22.9
22.10
22.11
N/A
N/A
N/A
N/A
N/A
N/A
Tests as described
22.12
N/A
N/A
N/A
Page 33 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
22.13
N/A
22.14
22.15
N/A
22.16
N/A
N/A
N/A
22.17
N/A
22.18
22.19
N/A
22.20
N/A
N/A
22.21
22.22
22.23
22.24
N/A
Page 34 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
(IEC/EN 60335-2-40)
Bare heating elements only used with metal
enclosures (wood or composite enclosures not
allowed)
(IEC/EN 60335-2-40)
N/A
22.25
N/A
22.26
22.27
N/A
22.28
N/A
22.29
N/A
22.30
22.31
22.32
N/A
N/A
N/A
N/A
Page 35 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
22.33
Result
Verdict
P
N/A
N/A
22.34
N/A
22.35
---
---
N/A
22.36
N/A
22.37
N/A
N/A
22.38
22.39
N/A
22.40
N/A
Page 36 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
22.42
N/A
N/A
22.43
N/A
22.44
22.45
22.46
N/A
22.47
N/A
N/A
22.48
N/A
22.101
22.102.1
---
---
---
Appliances provided with supplementary heaters Replaced by EN 60335-2for water incorporate a non-self-resetting
40/A2: 2009, See appendix
thermal cut-out, providing all-pole disconnection
---
22.102.2
---
Page 37 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
---
22.102.3
---
22.103
N/A
22.104
N/A
22.105
N/A
22.106
N/A
22.107
N/A
N/A
22.108
N/A
22.109
N/A
22.110
N/A
N/A
N/A
N/A
22.111
Page 38 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
22.112
22.113
N/A
N/A
N/A
22.114
N/A
22.115
N/A
22.116
N/A
N/A
All electrical components that could be a source of ignition and which could
function under normal conditions or in the event of a leak, comply with one of the
following:
(IEC/EN 60335-2-40/A1)
N/A
N/A
Page 39 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
(IEC/EN 60335-2-40/A1)
Be located in an enclosure. The enclosure
containing the electrical components comply
with IEC 60079-15:2001 for enclosures suitable
for use with group IIA gases or the refrigerant
used.
(IEC/EN 60335-2-40/A1)
N/A
22.117
N/A
22.118
N/A
N/A
N/A
N/A
N/A
N/A
23
INTERNAL WIRING
23.1
Page 40 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
23.2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
23.4
N/A
23.5
23.6
23.7
23.8
23.9
23.3
N/A
N/A
Page 41 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
24
COMPONENTS
24.1
---
List of components
---
---
Components not tested and found to comply with Replaced by IEC/EN 60335relevant IEC standard, components not marked or 1/A14: 2010, See appendix
not used in accordance with its marking, tested
under the conditions occurring in the appliance
---
24.1.2
24.1.3
24.1.4
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Automatic controls complying with IEC 60730-1 with relevant part 2. The number of
cycles of operation being:
- thermostats:
10 000
N/A
- temperature limiters:
1 000
N/A
3 000
N/A
N/A
Page 42 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
- timers:
3 000
N/A
:10 000
N/A
- energy regulators
N/A
N/A
100 000
N/A
N/A
N/A
N/A
N/A
N/A
N/A
24.1.6
N/A
24.2
N/A
24.1.5
24.3
Page 43 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
24.5
24.6
N/A
Measure voltage:
Indoor fan motor capacitor:
295 V (max.)
Limited: 495V
N/A
N/A
24.7
N/A
24.101
N/A
25
25.1
Appliance not intended for permanent connection to fixed wiring, means for
connection to the supply:
N/A
N/A
N/A
N/A
N/A
N/A
P
Page 44 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
N/A
N/A
N/A
25.4
25.5
Verdict
N/A
N/A
N/A
- type X attachment
N/A
- type Y attachment
N/A
N/A
25.6
N/A
25.7
---
---
---
---
Page 45 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
---
---
---
---
---
25.8
25.9
25.10
25.11
N/A
25.12
N/A
25.13
N/A
N/A
N/A
Flexing test:
N/A
- number of flexings..................................................
N/A
25.14
N/A
Page 46 of 139
IEC / EN 60335-2-40
Clause
25.15
25.16
Requirement Test
Result
Verdict
N/A
N/A
N/A
N/A
N/A
N/A
Pull and torque test of supply cord, values shown 100N; 0,35Nm
in table 12: pull (N); torque (not on automatic cord
reel) (Nm) .................................................................:
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Page 47 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
N/A
25.17
25.18
N/A
N/A
N/A
25.20
25.21
N/A
Appliance inlet:
N/A
N/A
N/A
N/A
25.19
25.22
25.23
Page 48 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
specified
If necessary, electric strength test of 16.3
N/A
25.24
25.25
N/A
26
26.1
26.2
26.3
Outdoor unit
N/A
N/A
N/A
N/A
N/A
Terminals for type X attachment and those for connection to fixed wiring so fixed
that when tightening or loosening the clamping means:
Page 49 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
Compliance checked by inspection and by the test Replaced by IEC/EN 60335of subclause 8.6 of IEC 60999-1, the torque
1/A2:2006, See appendix
applied being equal to two-thirds of the torque
specified. Nominal diameter of thread (mm);
screw category; torque (Nm)....................................:
---
26.4
26.5
N/A
N/A
N/A
26.6
---
N/A
26.7
N/A
26.8
26.9
N/A
26.10
N/A
N/A
26.11
Page 50 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
27
27.1
27.2
27.3
27.4
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Page 51 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
27.5
N/A
27.6
N/A
0,05
---
---
---
28
28.1
N/A
N/A
Page 52 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
28.3
28.4
29
N/A
P
P
N/A
N/A
Thread-cutting (self-tapping) screws only used for Replaced by IEC/EN 60335electrical connections if they generate a full form
1/A2:2006, See appendix
standard machine screw thread
---
---
---
N/A
---
---
Page 53 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Type A coating
(IEC/EN 60335-1/A1)
---
For motor-compressor complies with IEC 603352-34, parts related not checked
(IEC/EN 60335-2-40)
QXAS-D23zX090B
N/A
N/A
N/A
29.1.1
Verdict
(IEC/EN 60335-1/A1)
N/A
N/A
---
N/A
29.1.2
29.1.3
Page 54 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
voltage
29.1.4
29.1.5
29.2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
P
N/A
Page 55 of 139
IEC / EN 60335-2-40
Clause
29.2.1
Requirement Test
Result
Verdict
N/A
N/A
29.2.2
29.2.3
29.2.4
29.3.1
29.3.2
29.3.3
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Page 56 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
30
30.1
75 C for enclosure
External parts: at 40 C plus the maximum
temperature rise determined during the test of
clause 11, or at 75 C, whichever is the higher;
temperature (C).......................................................:
N/A
30.2
Relevant parts of non-metallic material adequately Replaced by IEC/EN 60335resistant to ignition and spread of fire
1/A2:2006, See appendix
---
30.2.1
---
---
---
30.2.2
Not applicable
(IEC/EN 60335-2-40)
N/A
30.2.3
---
---
Page 57 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
30.2.3.1
---
---
---
---
---
---
Test not carried out on material having a glowReplaced by IEC/EN 60335wire ignition temperature according to IEC 60695- 1/A2:2006, See appendix
2-13 as specified
---
30.2.3.2
30.2.4
31
Verdict
---
---
---
---
---
---
---
RESISTANCE TO RUSTING
Page 58 of 139
IEC / EN 60335-2-40
Clause
32
Requirement Test
Result
--
--
ANNEX A (INFORMATIVE)
ROUTINE TESTS
Description of routine tests to be carried out by
the manufacturer
3.1.9
Verdict
Not
checked
ANNEX B (NORMATIVE)
APPLIANCES POWERED BY RECHARGEABLE BATTERIES
N/A
N/A
N/A
N/A
N/A
N/A
Page 59 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
3.6.2
N/A
5.101
N/A
7.1
N/A
7.12
N/A
N/A
7.15
N/A
8.2
N/A
N/A
11.7
N/A
19.1
N/A
19.101
N/A
19.102
N/A
19.103
N/A
21.101
Appliances having pins for insertion into socketoutlets have adequate mechanical strength,
checked according to procedure 2 of IEC 68-2-32
N/A
Part of the appliance incorporating the pins subjected to the free fall test, procedure
2, of IEC 60068-2-32, the number of falls being:
N/A
N/A
N/A
Appliances having pins for insertion into socketoutlets tested as fully assembled as possible
N/A
22.3
Result
Verdict
Page 60 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
25.13
N/A
30.2
N/A
N/A
ANNEX C (NORMATIVE)
AGEING TEST ON MOTORS
N/A
Result
ANNEX D (NORMATIVE)
THERMAL MOTOR PROTECTORS
Verdict
N/A
ANNEX E (NORMATIVE)
NEEDLE-FLAME TEST
Needle-flame test carried out in accordance with IEC 60695-2-2, with the following
modifications:
Severities
---
Test procedure
8.2
---
8.4
---
---
---
---
8.5
10
---
However, for printed circuit boards, the duration of Replaced by IEC/EN 60335burning not exceeding 15 s
1/A2:2006, See appendix
---
Page 61 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
ANNEX F (NORMATIVE)
CAPACITORS
Capacitors likely to be permanently subjected to the supply voltage, and used for
radio interference suppression or voltage dividing, comply with the following
clauses of IEC 60384-14, with the following modifications:
1.5
Terminology
1.5.3
N/A
1.5.4
N/A
1.6
Marking
N/A
3.4
Approval testing
3.4.3.2
N/A
4.1
N/A
4.2
Electrical tests
4.2.1
N/A
4.2.5
N/A
4.2.5.2
N/A
N/A
N/A
N/A
N/A
Impulse voltage
N/A
Endurance
N/A
N/A
N/A
4.12
4.13
4.14
4.14.7
4.17
Result
Verdict
Page 62 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
N/A
ANNEX G (NORMATIVE)
SAFETY ISOLATING TRANSFORMERS
The following modifications to this standard are applicable for safety isolating
transformers:
7.1
N/A
N/A
N/A
Construction
N/A
4.18
17
22
29
N/A
ANNEX H (NORMATIVE)
SWITCHES
N/A
N/A
N/A
N/A
Mechanism
13
Page 63 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
N/A
15
15.1
Not applicable
N/A
15.2
Not applicable
N/A
15.3
N/A
17
Endurance
N/A
N/A
N/A
N/A
N/A
N/A
Clearances, creepage distances, solid insulation and coatings of rigid printed board
assemblies
N/A
20
6.6
ANNEX I (NORMATIVE)
MOTORS HAVING BASIC INSULATION THAT IS INADEQUATE FOR THE
RATED VOLTAGE OF THE APPLIANCE
N/A
ANNEX J (NORMATIVE)
COATED PRINTED CIRCUIT BOARDS
Climatic sequence
---
Page 64 of 139
IEC / EN 60335-2-40
Clause
6.6.1
Requirement Test
Result
Cold
--
ANNEX K (NORMATIVE)
OVERVOLTAGE CATEGORIES
---
N/A
N/A
--
Additional tests
This sub-clause is not applicable
--
6.9
6.8.6
Verdict
N/A
N/A
ANNEX L (INFORMATIVE)
GUIDANCE FOR THE MEASUREMENT OF CLEARANCES AND CREEPAGE
DISTANCES
Page 65 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
ANNEX M (NORMATIVE)
POLLUTION DEGREE
Result
Verdict
- pollution degree 1: no pollution or only dry, nonconductive pollution occurs. The pollution has no
influence
N/A
N/A
N/A
ANNEX N (NORMATIVE)
PROOF TRACKING TEST
The proof tracking test is carried out in accordance with IEC 60112 with the
following modifications:
Test apparatus
7.3
Test solutions
N/A
10
10.1
Procedure
N/A
Page 66 of 139
IEC / EN 60335-2-40
Clause
10.2
Requirement Test
Result
N/A
N/A
N/A
Report
N/A
ANNEX O (INFORMATIVE)
SELECTION AND SEQUENCE OF THE TESTS OF CLAUSE 30
Verdict
ANNEX P (INFORMATIVE)
GUIDANCE FOR THE APPLICATION OF THIS STANDARD TO APPLIANCES
USED IN WARM DAMP EQUABLE CLIMATES
5.7
N/A
11 and 13 is
+3
40 0 C
7.1
N/A
7.12
N/A
N/A
11
Heating
11.8
N/A
13
13.2
N/A
Page 67 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
exceeding 0.5mA
15
Moisture resistance
15.3
N/A
16
16.2
N/A
19
Abnormal operation
19.13
N/A
ANNEX Q (INFORMATIVE)
SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC CIRCUITS
ANNEX R (NORMATIVE)
SOFTWARE EVALUATION
Definitions
N/A
N/A
Information
N/A
N/A
N/A
N/A
H.11.12.7
Delete text
N/A
H.11.12.7.1
N/A
H.11.12.8
N/A
H.12.8.1
Replace text
N/A
H.12.13
N/A
H.2
H.7
H.11.12
Page 68 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
AA
ANNEX AA (INFORMATIVE)
Examples for operating temperatures of the appliance
BB
ANNEX BB (NORMATIVE)
Selected information about refrigerants
CC
ANNEX CC (INFORMATIVE)
Transportation, marking and storage for units that employ flammable
refrigerants
CC.1
N/A
CC.2
N/A
CC.3
N/A
CC.4
Storage of equipment/appliances
N/A
CC.5
N/A
DD
ANNEX DD (NORMATIVE)
Service operations
DD.1
Generals
N/A
DD.2
Symbols
N/A
DD.3
Information in manual
N/A
DD.4
Information on servicing
N/A
DD.5
N/A
DD.6
N/A
DD.7
Cabling
N/A
DD.8
N/A
DD.9
N/A
DD.10
N/A
DD.11
Charging procedures
N/A
DD.12
Decommissioning
N/A
DD.13
Labelling
N/A
DD.14
Recovery
N/A
EE
ANNEX EE (NORMATIVE)
Pressure Tests
EE.1
General
Page 69 of 139
IEC / EN 60335-2-40
Clause
Requirement Test
Result
Verdict
EE.2
EE.3
Measure pressure:
Indoor unit: 3,2MPa;
Outdoor unit: 3,2MPa
Measure pressure:
Indoor unit: 3,8MPa;
Outdoor unit: 4,2MPa
Tested pressure:
Indoor unit: 11,4MPa;
Outdoor unit: 12,6MPa
EE.4
N/A
EE.5
N/A
FF
ANNEX FF (NORMATIVE)
Leak simulation tests
FF.1
General
N/A
FF.2
Test methods
N/A
GG
ANNEX GG (NORMATIVE)
Charge limits, ventilation requirements and requirements for secondary
circuits
GG.1
N/A
GG.2
N/A
GG.3
N/A
GG.4
N/A
GG.5
N/A
GG.6
N/A
GG.7
N/A
Page 70 of 139
APPENDIX 1:
To complete the assessment according to EN 60335-1
the following requirements are considered as well :
th
Requirement Test
Result
Verdict
6.1
Class I
7.1
25.6
25.6
...
N/A
25.6
...
N/A
25.7
P
P
N/A
N/A
N/A
N/A
N/A
ANNEX ZC
(normative)
N/A
ANNEX ZD
(informative)
N/A
Page 71 of 139
Clause
Requirement Test
Result
Verdict
ZA
7.12
Not
checked
19.5
Not
checked
22.2
Not
checked
25.6
Not
checked
Not
checked
(EN 60335-1:2002)
Not
checked
Not
checked
Not
checked
Not
checked
Not
checked
Not
checked
Page 72 of 139
Clause
Requirement Test
Verdict
Not
checked
Not
checked
Not
checked
Not
checked
- UNE-EN 50075
Not
checked
SEV 6532-2:1991
plug type 15 3P+N+PE 250/400 V, 10 A
Not
checked
SEV 6533-2:1991
plug type 11 L+N 250 V, 10 A
Not
checked
SEV 6534-2:1991
plug type 12 L+N+PE 250 V, 10 A
Not
checked
Not
checked
25.8
Not
checked
ZB
7.1
(EN 60335-1:2002)
Not
checked
Not
checked
Not
checked
ZAA
Not
checked
(EN 60335-2-40/A11:2004)
Page 73 of 139
Clause
Requirement Test
Verdict
N/A
N/A
vessels
---
---
N/A
N/A
--N/A
Piping
---
---
N/A
N/A
N/A
---
---
N/A
N/A
ANNEX EMF
TRF No.: IECEN60335_2_40B
Intertek Testing Services Shenzhen Ltd. Guangzhou Branch
Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China
Tel: (86-20) 8213 9688 Fax: (86-20) 32057538
Page 74 of 139
Clause
Requirement Test
Verdict
Limit 100%
Max.: 1,735%
Page 75 of 139
TABLES:
10.1
P rated (W)
P measured
(W)
dP
Required dP
Remark
GWH24RD-K3DNA3C / at
230V~, 50Hz
3050
2214,9
-27,4%
+15%
Cooling mode
2700
2074,6
-23,2%
+15%
Heating mode
GWH24RD-K3DNA8C / at
230V~, 50Hz
4000
3986,0
-0,4%
+15%
Heating mode
10.2
11.8
I rated (A)
N/A
I measured (A)
dI
Required dI
Remark
Same as above
Ambient, t2 (C) ........................................................
T (C)
Thermocouple locations
Max. T (C)
cooling
heating
Supply cord
44,4
36,6
75
Relay ambient
35,7
30,9
T70
PCB
36,2
32,0
145
X capacitor
36,6
37,4
T100
Varistor
36,2
31,2
T85
43,9
39,6
Class E: 105
Inductance
45,7
48,4
Class E: 105
Terminal block
33,9
28,6
85
86,0
65,2
For reference
36,8
31,5
T70
Step motor
40,8
38,1
For reference
32,1
25,8
85
60,7
30,7
For reference
80,3
73,3
For reference
51,4
31,5
For reference
Indoor unit:
Outdoor unit:
Page 76 of 139
81,4
74,5
For reference
13,9
20,4
For reference
4-way valve
51,3
78,9
For reference
Terminal block
54,3
37,9
85
56,8
45,7
T105
Interconnection cord
40,7
36,9
75
Reactor
74,0
35,9
Class H: 165
PCB
52,7
35,7
145
X capacitor
38,8
33,6
T100
Relay ambient
37,0
31,5
T70
52,9
37,9
Class E: 105
Test corner
44,9
20,5
90
11.8
Ambient, t1 (C)......................................................... : 25
Temperature of winding
T1
(C)
R1 ()
R2 ()
25
194,0
248,9
234,5
98,4
79,2
115
25
188,8
237,9
224,3
92,5
73,8
115
Cooling
T (C)
Max. T Insulation
class
(C)
25
1970
-2403
-82,0
120
B
4 ways valve
Remark:
1. The resistance method for 4 ways valve only conducted under heating operation mode because it
only operated at this mode.
2. The outdoor fan motor LW92K-ZL is DC type motor which is difficult to conduct resistance method.
13.2
N/A
240x1,06=254,4V
I (mA)
L: 0,33; N: 0,34
3,5
L: 0,024; N: 0,023
0,25
Page 77 of 139
Test voltage applied between:
1000
No
1750
No
3000
No
14
Clearance between:
16.2
Cl (mm)
N/A
Required
Cl (mm)
Rated impulse
voltage (V)
Impulse test
voltage (V)
Flashover
(Yes/No)
240x1,06=254,4V
N/A
I (mA)
Max.: 0,82
3,5
Max.: 0,054
0,25
16.3
Voltage (V)
Breakdown
(Yes/No)
1250
No
1750
No
3000
No
17
N/A
Temperature of part/at:
19.2
dT (C)
Max. dT (C)
Enclosure
temperature(C)
Winding
temperature
(C)
HV test performed
with 1250V
Leakage
current
(mA)
FN25A-PG (Kaibang)
103,1
114,5
Pass
0,052
LW92K-ZL (Kaibang)
86,4
127,0
Pass
0,051
Measured sample
Page 78 of 139
Report. No.: GZ12100571-1R3
Remark:
The temperature limited for enclosure is 150C, for Class E is 165C, and the Leakage current is 2 mA.
19.14
Temperature T of part / at :
T (C)
Required T (C)
Test corner
47,1
175
Supply cord
37,1
175
Test corner
Maximum: 44,8
175
Supply cord
Maximum: 45,9
175
Test corner
Maximum: 53,7
175
Supply cord
Maximum: 50,7
175
Test corner
Maximum: 44,1
175
Supply cord
Maximum: 47,8
175
19.4
19.5
19.7
19.10
24.1
TABLE: Components
Object / part
No.
Manufacturer/
trademark
P
Type / model
Technical data
Standard
Mark(s) of
conformity
3G2,5 mm
Alternative
Changzhou
Hongchang
Electronics Co., Ltd.
H05VV-F
3G2,5 mm
Alternative
Various
H05VV-F
3G2,5 mm
4G2,5 mm
Alternative
4G2,5 mm
Eastwire Industrial
Limited
H07RN-F
Alternative
Page 79 of 139
H07RN-F
4G2,5 mm
Various
4G0,75 mm
Alternative
4G0,75 mm
3G2,5 mm
Alternative
Eastwire Industrial
Limited
H07RN-F
3G2,5 mm
Alternative
Various
H07RN-F
3G2,5 mm
Step Motor
Jiangsu Huayang
Electrical Appliance
Co.; Ltd
MP35XX
12VDC;Class A;
1308%
EN 60335-2-40
Tested with
appliance
Alternative
Changzhou Oukai
Electrical Appliance
Co.; Ltd
MP35XX
12VDC;Class A;
1308%
EN 60335-2-40
Tested with
appliance
Indoor fan
motor
Tested with
appliance
-Fan Motor
Protector
250V; 5A;
Operation:100C
EN 60730-1
VDE
40015984
-Alternative
Changzhou
KW Series
Changhong Tongli
Electric Appliance Co.
Ltd.
250V; 8A;
Operation:100C
EN 60730-1
250V; 8A;
Operation:100C
EN 60730-1
-Fan motor
capacitor
CBB61-1
EN 60252-1
TV
Rheinland
R50128479
-Alternative
CBB61
2,5uF; 500VAC;
T70
EN 60252-1
TV
Rheinland
R50120798
-Alternative
Xiamen Faratronic
Co., Ltd.
CBB61
2,5uF; 450VAC;
T70
EN 60252-1
VDE
40004094
-Alternative
NINGBO SHINE
ELECTRICAL CO.
LTD.
CBB61A
2,5uF; 450VAC;
T70
EN 60252-1
TV
Rheinland
R50065558
-Alternative
Various
S05RN-F
EN 60730-2-2
EN 60730-2-2
EN 60730-2-2
VDE
40020906
KEMA
2089558.01
Page 80 of 139
MKNS255
2,5uF; 450VAC;
T70
CBB61
2,5uF; 450VAC;
T70
EN 60252-1
VDE
40006835
XS-PL-06
220-240VAC;
50/60Hz; 2W
EN 60335-1; EN
60335-2-65
TV
Rheinland
R50172899
Main board
only for A1
GREE
M846F2TJ
--
EN 60335-2-40
Tested with
appliance
Main board
only for A2
GREE
M846F2TAJ
--
EN 60335-2-40
Tested with
appliance
Main board
only for A3
GREE
M846F2UEJ
--
EN 60335-2-40
Tested with
appliance
MKP62
275VAC; 104M;
T110
EN 132400;
VDE
40000358
-Alternative
Anhui Xinyang
Electronics Co., Ltd.
MKP
0,1F; AC275V;
T100
IEC 60384-14;
OKAYA Electric
Industries Co., Ltd.
LE104
275VAC; 0,1F;
T100
IEC 60384-14;
Various
Various
0,1F; AC275V;
T100 or above
IEC 60384-14;
275VAC; 224K;
T110; X2
EN 132400;
275VAC; 0,22F;
T100
IEC 60384-14;
0,22F; AC275V;
X2; T100 or above
IEC 60384-14;
-Alternative
Shanghai Haoye
Capacitors Co., Ltd.
-Alternative
Foshan Shunde
Fongming Electronic
Tech. Co., Ltd.
-Alternative
-Alternative
MKP62
-Alternative
OKAYA Electric
Industries Co., Ltd.
LE224
Various
Various
-Alternative
IEC 60384-14
EN 132400
EN 132400
EN 132400
IEC 60384-14
EN 132400
EN 132400
VDE
40024537
SEMKO
SE/0142-1D
S or other
EU
certification
marks
VDE
40000358
SEMKO
SE/0142-1D
S or other
EU
certification
marks
-Y capacitor
TDK-EPC
Corporation,
Capacitors Group
CS103M
VDE
40029781
-Alternative
Various
Various
S or other
EU
certification
marks
-Y capacitor
for A3
KX472M
250VAC; 472M
IEC 60384-14
EN 60384-14
VDE
40002831
-Alternative
Various
Various
250VAC; 472M
IEC 60384-14
EN 60384-14
S or other
EU
certification
marks
Page 81 of 139
-Varistor
Chengdu Tieda
Electronic Co., Ltd.
MYN15-621K
385VAC; T85
VDE
40008571
CECC 42201
-Alternative
Xianhua Advanced
FNR-14K621
Sensitive Components
Co., Ltd.
380VAC; T85
CECC 42000;
CECC 42200;
VDE
40008242
-Optocoupler
Sharp Corporation
PC817
VDE
40008087
-Alternative
Sharp Corporation
PC851
Vceo:350V;
If:50mA; Ic:50mA
EN 60747-5-2
VDE
40008087
-PCB
material
DOOSAN
CORPORATION
ELECTROMATERIALS BG
DS-7106
CEM-1; 94V-0;
1,6mm
EN 60335-2-40;
UL 94
Tested with
appliance &
UL
E103670
-Alternative
CHANG CHUN
PLASTICS CO LTD
CCP-508U
CEM-1; 94V-0;
1,6mm
EN 60335-2-40;
UL 94
Tested with
appliance &
UL
E108591
-Alternative
PACIFIC
INSULATING
MATERIAL CO LTD
P-121
CEM-1; 94V-0;
1,6mm
EN 60335-2-40;
UL 94
Tested with
appliance &
UL
E115974
-Alternative
GUANGDONG
S3116
SHENGYI SCI TECH
CO LTD
CEM-1; 94V-0;
1,6mm
EN 60335-2-40;
UL 94
Tested with
appliance &
UL
E109769
-Alternative
Various
Various
CEM-3 or FR-4;
94V-0; CTI 3;
thickness:
1,60,4mm
UL 94;
IEC 60707
S, ETL, UL
or other EU
certification
marks
-High
Frequency
Transformer
ECO20-11P
LEN 60335-2-40
Pri.:550uH10%;
Lk-Pri:9,5uH MAX;
12,5V/0,8A;
15V/100mA; Class
E
Tested with
appliance
-Alternative
SHENZHEN YAMAXI
ELECTRONICS CO.,
LTD
ECO20-11P
Tested with
appliance
CECC 42201
Page 82 of 139
200uH
200uH/2A
-Inductance
Hangzhou Ruichuang
Industry And Trade
Co., Ltd.
-Alternative
200uH/2A
EN 60335-2-40
Tested with
appliance
-Alternative
Shenzhen Yamaxi
Electronic Co., Ltd.
T50-26
200uH/2A
EN 60335-2-40
Tested with
appliance
-Alternative
HUIZHOU JIAYANG
ELECTRONIC NEWTECH CO., LTD
200uH/2A
200uH/2A
EN 60335-2-40
Tested with
appliance
-Alternative
Fenghua Advanced
Technology(Holding)
Co., Ltd.
200uH/2A
200uH; 2A
EN 60335-2-40
Tested with
appliance
-Alternative
Dongguan Dazhong
Electronic Co., Ltd.
200uH/2A
200uH; 2A
EN 60335-2-40
Tested with
appliance
-Filter
AC250V; 0,5A
EN 60335-2-40
Tested with
appliance
-Alternative
SHENZHEN YAMAXI
ELECTRONIC
CO.LTD
SF2022A05220
AC250V; 0,5A
EN 60335-2-40
Tested with
appliance
-Alternative
DAZHONG
ELECTRONIC
CO.LTD
SF2022A05220
AC250V; 0,5A
EN 60335-2-40
Tested with
appliance
-Relay 1#
Electronics(Shenzhen) PCF-112D2M
Co.; Ltd.
250VAC; 25A;
EN 61810-1
250VAC; 20A; T55;
100000 cycles
TV
Rheinland
R50139097
-Alternative
G4A-1A-E
TV
Rheinland
R50214482
-Alternative
OMRON Corporation
G4A-1A-E
VDE
107293
-Relay 2#
Xiamen Hongfa
Electroacoustic Co.,
Ltd.
JZC-43F
EN 61810-1
EN 60255-23
VDE
40002220
-Alternative
Omron Electronic
Components
(Shenzhen)LTD
G5NB-1A
EN 60255-23
VDE
137575
-Alternative
Dongguan Sanyou
Electrical Appliances
Co., Ltd.
EN 61810-1
TV
Rheinland
R50138320
-Alternative
Songchuan Precision
Co., Ltd.
202N-1AC-C
EN 61810-1
VDE
40008369
-Alternative
Tyco Electronics
(Shenzhen) Co., Ltd.
PCJ-112D3M
EN 61810-1
VDE
40009151
-Alternative
Dongguan Churod
Electronics Co., Ltd.
CHM-S112DA3
EN 61810-1
TV
Rheinland
R50196152
Page 83 of 139
-Relay 3#
(SSR)
AQH2223
VDE
40004928
50CT
AC 250 V; T; H;
3,15A; 5 x 20 mm
VDE
40014896
-Alternative
TSC
VDE
40016670
-Alternative
Various
Various
AC 250 V; T; H;
3,15A; 5 x 20 mm
EN 60127-1;
S or other
EU
certification
marks
AC600V; 1,5A
EN 60335-2-40
Tested with
appliance
Terminal
Changzhou
JX-G-4C
board (4 bits) Changheng Kaidu
Electric Appliance Co.,
Ltd.
AC250V; 2,5mm
EN 60998-1
VDE
40020936
Alternative
Zhenjiang Honglian
Electrician Co.; Ltd.
JX1239
250V; 2,5mm
EN 60335-2-40
Tested with
appliance
Alternative
Nantong Huaguan
Electric Co., Ltd.
JXW-4-G1
AC250V; 2,5mm
EN 60998-1
VDE
40013197
-Rectifier
Matsushita Electric
Works Ltd.
SHINDENGEN
ELECTRIC MFG CO
LTD
NC 80
EN 60127-1;
EN 60127-2
EN 60127-2
EN 60998-2-1
EN 60998-2-1
Outdoor unit:
Terminal
board
Changzhou
JXD-3
Changheng Kaidu
Electric Appliance Co.,
Ltd.
AC450V; 2,5mm
Alternative
Nantong Huaguan
Electric Co., Ltd.
EN 60335-2-40
Tested with
appliance
AC450V;
2
2,5mm (24A)
EN 60335-2-40
Tested with
appliance
Terminal
Changzhou
JX-G-5H
board (5 bits) Changheng Kaidu
for A3
Electric Appliance Co.,
Ltd.
AC300V; 4,0mm
EN 60335-2-40
Tested with
appliance
Alternative
Nantong Huaguan
Electric Co., Ltd.
JXW
AC300V; 4,0mm;
32A
EN 60335-2-40
Tested with
appliance
Compressor
Zhuhai Landa
Compressor Co., Ltd.
QXASD23zX090B
EN 60335-2-34
TV
Rheinland
R50135262
JXW
EN 60335-1
-Thermal
protecor of
compressor
Operation:
1153C; Reset:
955C
EN 60730-1
-Alternative
Changzhou
Changrong Electrical
Appliance Co., Ltd
Operation: 115C;
Reset: 95C
EN 60730-1
EN 60730-2-9
HPC
EN 60730-2-9
KEMA
2014531.16
VDE
40032296
-Alternative
Jiangsu Changheng
(Group) Control
Devices & Products
Co., Ltd.
Chassiss
electrical
heater only
for
GWH24RDK3DBA5E
and
GWH24RDK3DBE1E
Outdoor fan
motor
Zhenjiang Dongfang
Electric Heating
Technology Co., Ltd.
Page 84 of 139
KSD
Operation: 115C;
Reset: 95C
DYQ-02-I-230
230V; 160W
EN 60335-2-40
Tested with
appliance
200-370VDC;
90W; Class E
EN 60335-2-40
Tested with
appliance
DSF-9-R410A AC220V-240V;
EN 60730-1
50/60Hz; 7/5W;
1970197; Class
B
VDE
40013212
Alternative
Zhejiang Dunan
Artificial Environment
Co.; Ltd.
DSF-9-R410A AC220-240 V;
EN 60730-1
50/60Hz; 4-6 W;
1470100; Class
B
TV
Rheinland
R 50017212
Alternative
Zhejiang Sanhua
SHF-7H-34UClimate and Appliance PG
Controls Group Co.,
Ltd.
220-240V;
EN 60730-1
50/60Hz; 4,5/3,5W;
Class B;
2085208
VDE
40003240
Reactor
QINGDAO YUNLU
ENERGY
TECHNOLOGY CO
LTD
R 315D
3mH/22A; 60m
(20C); Class H
EN 60335-2-40
tested with
appliance
Alternative
L3mH/22A
3mH/22A; 60m
(20C); Class H
EN 60335-2-40
tested with
appliance
Main Board
GREE
W8303GB(TI)
---
EN 60335-2-40
Tested with
appliance
-Fuse 1#
HOLLYLANDCOLTD
65TS
AC250V; 30A
EN 60127-1
TV
Rheinland
J50136250
EN 60127-2
-Fuse 2#
Walter Electronic
Co.Ltd.
ICP
-Alternative
Various
Various
S or other
EU
certification
marks
-Y capacitor
TDK-EPC
Corporation,
Capacitors Group
CS103M
VDE
40029781
EN 60127-3
VDE
40012824
Page 85 of 139
Report. No.: GZ12100571-1R3
250VAC; 103M; Y2 IEC 60384-14;
Various
S or other
EU
EN 132400
certification
marks
-Alternative
Various
-X capacitor
1#
Xiamen Faratronic
Co., Ltd.
MKP62
EN 60384-14
VDE
40000358
-Alternative
Anhui Xinyang
Electronics Co., Ltd.
MKP
VDE
40024537
-Alternative
PCX2 335M
ENEC:
EN 60384-14
SE/0256-2
-Alternative
Various
Various
1,0F; AC275V;
T85 or above; X2
IEC 60384-14;
EN 132400
S or other
EU
certification
marks
-X capacitor
2#
EN 60384-14
VDE
40000358
-Alternative
Okaya Electric
Industries Co.; Ltd.
LE225
2,2F; 275V;T100
EN 60384-14
ENEC:SE/0
142-1D
-Alternative
Various
Various
2,2F; AC275V;
T100; X2
IEC 60384-14;
S or other
EU
certification
marks
275VAC; 104M;
T110
EN 132400;
0,1F; AC275V;
T100
IEC 60384-14;
275VAC; 0,1F;
T100
IEC 60384-14;
0,1F; AC275V;
T100 or above
IEC 60384-14;
MKP62
-Alternative
Anhui Xinyang
Electronics Co., Ltd.
MKP
OKAYA Electric
Industries Co., Ltd.
LE104
Various
Various
-Alternative
-Alternative
EN 132400
IEC 60384-14
EN 132400
EN 132400
EN 132400
VDE
40000358
VDE
40024537
SEMKO
SE/0142-1D
S or other
EU
certification
marks
-PTC
Resistance
MZ8I EB500K
R:5010%
EN 60335-2-40
Tested with
appliance
-Alternative
Dandong Guotong
Electronic
Components Co., Ltd
MZ9250RM
R:5010%
EN 60335-2-40
tested with
appliance
-Optocoupler
Toshiba Corporation
TLP781
VDE
40021173
Page 86 of 139
-High
Frequency
Transformer
DONGGUAN
DAZHONG
ELECTRONIC
LTD
-Inductance
ECO2020
Tested with
appliance
10uH; 1,5A
EN 60335-2-40
Tested with
appliance
-Alternative
Shenzhen Yamaxi
Electronic Co., Ltd.
10uH
10uH; 1,5A
EN 60335-2-40
Tested with
appliance
-Alternative
Dongguan Dazhong
Electronic Co., Ltd.
10uH
10uH; 1,5A
EN 60335-2-40
Tested with
appliance
-PCB
material
CHANG CHUN
PLASTICS CO LTD
CCP-508U
CEM-1; 94V-0;
1,6mm
EN 60335-2-40;
UL 94
Tested with
appliance &
UL
E108591
-Alternative
PACIFIC
INSULATING
MATERIAL CO LTD
P-121
CEM-1; 94V-0;
1,6mm
EN 60335-2-40;
UL 94
Tested with
appliance &
UL
E115974
-Alternative
S3116
GUANGDONG
SHENGYI SCI TECH
CO LTD
CEM-1; 94V-0;
1,6mm
EN 60335-2-40;
UL 94
Tested with
appliance &
UL
E109769
-Alternative
Various
Various
CEM-3 or FR-4;
94V-0; CTI 3;
thickness:
1,60,4mm
UL 94;
IEC 60707
S, ETL, UL
or other EU
certification
marks
SLA6868M
VDSS: 500V;
VCC:20V; I:2,5A;
IP: 5A; PD: 32,8W
EN 60335-2-40
Tested with
appliance
EN 60335-2-40
Tested with
appliance
CO.,
MITSUBISHI
ELECTRIC CORP
SEMICONDUCTOR
DIV
PS21997-AST Operation:600V;
30A; Fsw=20KHz;
Viso=2500V
-Relay 1#
Xiamen Hongfa
Electroacoustics Co.,
Ltd.
JQX-102F
-Alternative
TV
Rheinland
R50214482
-Alternative
OMRON Corporation
VDE
107293
-Alternative
Dongguan Sanyou
Electrical
Appliances Co., Ltd.
SFK-112DM
VDE
40007481
AC250 V; 20 A;
EN 61810-1
T85; 100000cycles
VDE
40024142
Page 87 of 139
Report. No.: GZ12100571-1R3
Song Chuan Precision 891WP-1A-C AC250 V; 25A;
EN 61810-1
TV
Co., Ltd.
Rheinland
T85; 100000cycles EN 61810-5
R50003966
EN 60255-23
-Alternative
-Alternative
Tyco Electronics
(Shenzhen)
Co., Ltd.
EF00-1A2D012-F
AC250 V; 20A;
EN 61810-1
T85; 100000cycles
TV
Rheinland
R50117320
-Relay 2#
Xiamen Hongfa
Electroacoustics Co.,
Ltd.
JZC-32F
EN 61810-1
VDE
40012204
-Alternative
Dongguan Sanyou
Electrical Appliances
Co., Ltd.
SJ-S-112DM
EN 61810-1
VDE
40002146
EN 61810-1
-Alternative
EN 60255-23
IEC 61810-1
TV
Rheinland
R 50128391
-Alternative
Tyco Electronics
(Shenzhen) Co., Ltd.
OJE-SS112DM
EN 61810-1
IEC 61810-1
TV
Rheinland
R50139166
-Alternative
Tyco Electronics
(Shenzhen)
Co., Ltd.
OJT-SH112DM
-Relay 3#
Xiamen Hongfa
Electroacoustics Co.,
Ltd.
HF32F-G
VDE
40012204
-Alternative
Dongguan Sanyou
Electrical Appliances
Co., Ltd.
SJ-S-112DM
TV
Rheinland
R50142420
-Alternative
VDE
-Alternative
Tyco Electronics
(Shenzhen)
Co., Ltd.
OJE-SS112HMF
TV
Rheinland
R50139166
-Alternative
Dongguan Churod
Electronics Co., Ltd.
A1-S-112HAF
TV
Rheinland
R50174892
-Rectifier
Shanghai Microsemi
Semiconductor Co.,
Ltd.
GBJ25J
600V; 25A
EN 60335-2-40
Tested with
appliance
-Alternative
SHINDENGEN
ELECTRIC MFG CO
LTD
D25XB 60
600V; 25A
EN 60335-2-40
Tested with
appliance
28.1
EN 61810-1
EN 60255-23
VDE
40007630
40010643
Diameter of thread
(mm)
Column number
(I, II, or III)
Applied torque ( Nm )
4,0
II
1,2
Page 88 of 139
29.1
TABLE: Clearances
Overvoltage category.... :
II
Type of insulation:
Rated impulse
voltage (V):
Min. cl
(mm)
Basic
Functional
Supplementary
Reinforced
Verdict / Remark
330
0,5
---
---
---
---
N/A
500
0,5
---
---
---
---
N/A
800
0,5
---
---
---
---
N/A
1 500
0,5
---
---
---
---
N/A
2 500
1,5
3,5
4,0
>5,0
---
Pass
4 000
3,0
---
---
---
>10,0
Pass
6 000
5,5
---
---
---
---
N/A
8 000
8,0
---
---
---
---
N/A
10 000
11,0
---
---
---
---
N/A
29.2
Working voltage
(V)
Creepage distance
(mm)
Pollution degree
1
Material group
Material group
II
IIIa/IIIb
II
Type of insulation
IIIa/IIIb
B*
S*
R*
Verdict
N/A
N/A
50
0,2
0,6
0,9
1,2
1,5
1,7
1,9
50
0,2
0,6
0,9
1,2
1,5
1,7
1,9
50
0,4
1,2
1,8
2,4
3,0
3,4
3,8
0,3
0,8
1,1
1,5
1,9
2,1
2,4
0,3
0,8
1,1
1,5
1,9
2,1
2,4
0,6
1,6
2,2
3,0
3,8
4,2
4,8
0,6
1,3
1,8
2,5
3,2
3,6
4,0
3,5
0,6
1,3
1,8
2,5
3,2
3,6
4,0
>5,0
1,2
2,6
3,6
5,0
6,4
7,2
8,0
>15
1,0
2,0
2,8
4,0
5,0
5,6
6,3
N/A
1,0
2,0
2,8
4,0
5,0
5,6
6,3
N/A
2,0
4,0
5,6
8,0
10,0
11,2
12,6
N/A
1,3
2,5
3,6
5,0
6,3
7,1
16,0
N/A
1,3
2,5
3,6
5,0
6,3
7,1
8,0
2,6
5,0
7,2
10,0
12,6
14,2
16,0
1,8
3,2
4,5
6,3
8,0
9,0
10,0
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1,8
3,2
4,5
Page 89 of 139
6,3
8,0
9,0
3,6
6,4
9,0
12,6
16,0
18,0
20,0
2,4
4,0
5,6
8,0
10,0
11,0
12,5
2,4
4,0
5,6
8,0
10,0
11,0
12,5
4,8
8,0
11,2
16,0
20,0
22,0
25,0
3,2
5,0
7,1
10,0
12,5
14,0
16,0
3,2
5,0
7,1
10,0
12,5
14,0
16,0
6,4
10,0
14,2
20,0
25,0
28,0
32,0
4,2
6,3
9,0
12,5
16,0
18,0
20,0
4,2
6,3
9,0
12,5
16,0
18,0
20,0
8,4
12,6
18,0
25,0
32,0
36,0
40,0
5,6
8,0
11,0
16,0
20,0
22,0
25,0
5,6
8,0
11,0
16,0
20,0
22,0
25,0
11,2 16,0
22,0
32,0
40,0
44,0
50,0
7,5
10,0
14,0
20,0
25, 0 28,0
32,0
7,5
10,0
14,0
20,0
25, 0 28,0
32,0
15,0 20,0
28,0
40,0
50,0
56,0
64,0
10,0 12,5
18,0
25,0
32,0
36,0
40,0
10,0 12,5
18,0
25,0
32,0
36,0
40,0
20,0 25,0
36,0
50,0
64,0
72,0
80,0
12,5 16,0
22,0
32,0
40,0
45,0
50,0
12,5 16,0
22,0
32,0
40,0
45,0
50,0
25,0 32,0
44,0
64,0
80,0
90,0
100,0
16,0 20,0
28,0
40,0
50,0
56,0
63,0
16,0 20,0
28,0
40,0
50,0
56,0
63,0
32,0 40,0
56,0
80,0
100,0
112,0
126,0
20,0 25,0
36,0
50,0
63,0
71,0
80,0
20,0 25,0
36,0
50,0
63,0
71,0
80,0
40,0 50,0
72,0
100,0
126,0
142,0
160,0
25,0 32,0
45,0
63,0
80,0
90,0
100,0
25,0 32,0
45,0
63,0
80,0
90,0
100,0
50,0 64,0
90,0
126,0
160,0
180,0
200,0
32,0 40,0
56,0
80,0
100,0
110,0
125,0
32,0 40,0
56,0
80,0
100,0
110,0
125,0
64,0 80,0
112,0
160,0
200,0
220,0
250,0
71,0
100,0
125,0
140,0
160,0
10,0
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
71,0
Page 90 of 139
100,0
125,0 140,0
142,0
200,0
250,0
280,0
320,0
N/A
Working voltage
(V)
Creepage distance
(mm)
Pollution degree
1
Material group
Material group
II
IIIa/IIIb
II
IIIa/IIIb
Verdict / Remark
50
0,2
0,6
0,8
1,1
1,4
1,6
1,8
N/A
0,3
0,7
1,0
1,4
1,8
2,0
2,2
N/A
0,4
1,0
1,4
2,0
2,5
2,8
3,2
0,8
1,6
2,2
3,2
4,0
4,5
5,0
N/A
1,0
2,0
2,8
4,0
5,0
5,6
6,3
N/A
1,8
3,2
4,5
6,3
8,0
9,0
10,0
N/A
2,4
4,0
5,6
8,0
10,0
11,0
12,5
N/A
3,2
5,0
7,1
10,0
12,5
14,0
16,0
N/A
4,2
6,3
9,0
12,5
16,0
18,0
20,0
N/A
5,6
8,0
11,0
16,0
20,0
22,0
25,0
N/A
7,5
10,0
14,0
20,0
25,0
28,0
32,0
N/A
10,0 12,5
18,0
25,0
32,0
36,0
40,0
N/A
12,5 16,0
22,0
32,0
40,0
45,0
50,0
N/A
16,0 20,0
28,0
40,0
50,0
56,0
63,0
N/A
20,0 25,0
36,0
50,0
63,0
71,0
80,0
N/A
25,0 32,0
45,0
63,0
80,0
90,0
100,0
N/A
32,0 40,0
56,0
80,0
100,0
110,0
125,0
N/A
71,0
100,0
125,0
140,0
160,0
N/A
TABLE 30
Page 91 of 139
Manufacturer
Type
75C
Terminal block
Terminal block
cl. 11
cl. 19
+40C 125C +25C
Tracking
test
GWT
[CTI/
550C
PTI]
GWT
650C
GWT
750C
GWFI
850C
GWIT
Needleflame
test
Verdict
Honglian
----
----
----
0,8
----
----
----
----
No flame
Ti:12,1s;
Te:32,0s
----
----
Kaidu
----
----
----
1,2
----
----
----
----
No flame
Ti:1,4s;
Te: 31,4s
----
----
----
----
1,3
----
----
----
----
Ti:1,4
s; Te:
31,7s
----
----
----
----
----
----
----
----
----
1,0
----
----
----
----
----
----
----
----
Enclosure
PCB
Page 92 of 139
Photo documents:
Following photos are for all indoor units except especial note:
Page 93 of 139
Page 94 of 139
Top view
Back view
Page 95 of 139
Page 96 of 139
Control panel
location
Page 97 of 139
Page 98 of 139
Earthing terminal
Page 99 of 139
Cold plasma
generator
Front view
Side view
Side view
Temperature
sensor
Back view
Top view
Reactor view
Compressor view
Chassiss electric heater view only for model GWH24RD-K3DBA5E and GWH24RD-K3DBA3E
Requirement Test
5.3
(Addition:)
Result
Verdict
--N/A
---
7.5
(Replacement:)
(Replacement:)
N/A
N/A
N/A
(Addition:)
---
8.1.1
Requirement Test
Verdict
N/A
--N/A
N/A
(Replacement)
10
10.1
(Addition:)
--N/A
N/A
Requirement Test
unless
Verdict
( IEC/EN 60335-1/A2:2006)
(Addition:)
(Addition:)
N/A
N/A
N/A
11
HEATING
(Replacement:)
--N/A
N/A
N/A
N/A
N/A
Requirement Test
Verdict
14
---
N/A
N/A
N/A
TRANSIENT OVERVOLTAGES
(Replacement:)
--N/A
N/A
(IEC/EN 60335-1/A2:2006)
16
---
16.3
(Replacement:)
19
ABNORMAL OPERATION
This clause of part 1 is replaced by part 2.
22
CONSTRUCTION
22.2
(Replacement:)
--N/A
--N/A
Requirement Test
conductor.
22.5
Verdict
(IEC/EN 60335-1/A2:2006)
(Replacement:)
N/A
22.21
N/A
(Addition:)
N/A
(Addition:)
N/A
(Replacement:)
N/A
22.40
N/A
(Addition:)
N/A
(Replacement:)
Requirement Test
22.49
(Addition:)
Verdict
N/A
(Addition:)
N/A
(Addition)
N/A
(Addition :)
N/A
24
COMPONENTS
24.1
(Replacement:)
Components not tested and found to comply
with relevant IEC standard for the number of
cycles specified are tested in accordance with
24.1.1 to 24.1.9 (IEC/EN 60335-1/A2:2006)
(Addition:)
Lampholders and starterholders that have not
been previously tested and found to comply
with the relevant IEC standard are tested as a
part of the appliance and shall additionally
comply with the gauging and interchangeability
requirements of the relevant IEC standard
under the conditions occurring in the
appliance.
---
---
(IEC/EN 60335-1/A2:2006)
TRF No.: IECEN60335_2_40B
Intertek Testing Services Shenzhen Ltd. Guangzhou Branch
Block E, No.7-2 Guang Dong Software Science Park, Caipin Road, Guangzhou Science City, GETDD, Guangzhou, China
Tel: (86-20) 8213 9688 Fax: (86-20) 32057538
Clause
Requirement Test
Result
24.1.7
(Addition:)
Verdict
---
(IEC/EN 60335-1/A2:2006)
24.1.8
(Addition:)
N/A
(Addition:)
25
---
25.7
(Replacement:)
---
N/A
H05VV-F
N/A
---
N/A
N/A
---
Requirement Test
Result
Verdict
These cords shall not be used for type X attachment other than specially
prepared cords. Their properties shall be at least those of (IEC/EN 603351/A2:2006)
heat-resistant light polyvinyl chloride
sheathed cord (code designation 60227 IEC
56), for appliances having a mass not
exceeding 3 kg; (IEC/EN 60335-1/A2:2006)
N/A
N/A
26
26.3
(Replacement:)
--N/A
(Replacement:)
Terminals for type X attachment and for
connection to fixed wiring suitable for
connection of conductors with required crosssectional area according to table 13; rated
current (A); nominal cross-sectional area
(mm):
27
27.6
(Replacement:)
--N/A
28
N/A
---
Requirement Test
28.1
(Replacement:)
Verdict
N/A
(Replacement:)
N/A
N/A
(IEC/EN 60335-1/A2:2006)
Thread-cutting, thread rolling and spacethreaded screws may be used in connections
providing earthing continuity provided it is not
necessary to disturb the connection:
N/A
in normal use,
during user maintenance,
when replacing a supply cord having a type
X attachment, or
during installation.
(IEC/EN 60335-1/A2:2006)
At least two screws must be used for each
connection providing earthing continuity unless
the screw forms a thread having a length of at
least half the diameter of the screw. (IEC/EN
60335-1/A2:2006)
29
N/A
--N/A
29.1.1
N/A
N/A
(Replacement:)
Requirement Test
Verdict
30
---
30.2
(Replacement:)
N/A
N/A
P
N/A
(IEC/EN 60335-1/A2:2006)
30.2.1
(Replacement:)
30.2.2
N/A
N/A
(Replacement:)
N/A
Requirement Test
Verdict
N/A
(IEC/EN 60335-1/A2:2006)
-750C, for connections carrying a current
exceeding 0,5A during normal operation
N/A
N/A
N/A
NOTE 1 The preferred values in IEC 60695-212 are 0,75 mm 0,1 mm, 1,5 mm 0,1 mm
and 3,0 mm 0,2 mm. (IEC/EN 603351/A2:2006)
Where a non-metallic material is within 3 mm
of a current carrying connection, but is
shielded from the connection by a different
material, the glow-wire test of IEC 60695-2-11
is carried out at the relevant temperature with
the tip of the glow-wire applied to the
interposed shielding
N/A
30.2.3
N/A
N/A
N/A
(Replacement:)
30.2.3.1
(Replacement:)
Requirement Test
Verdict
30.2.3.2
N/A
N/A
N/A
(Replacement:)
N/A
Test not carried out on material having a glowwire ignition temperature according to IEC
60695-2-13 of at least: (IEC/EN 603351/A2:2006)
N/A
N/A
N/A
N/A
Requirement Test
Verdict
N/A
30.2.4
N/A
N/A
N/A
N/A
(IEC/EN 60335-1/A2:2006)
Test not applicable to conditions as specified
(IEC/EN 60335-1/A2:2006)
32
N/A
--N/A
Requirement Test
(Replacement:)
Verdict
N/A
ANNEX E (NORMATIVE)
NEEDLE-FLAME TEST (IEC/EN 60335-1/A2:2006)
---
Severities
---
(Replacement:)
Test procedure
---
9.1
(Modification:)
(Modification:)
N/A
(Replacement:)
N/A
--N/A
ANNEX J (NORMATIVE)
COATED PRINTED CIRCUIT BOARDS (IEC/EN 60335-1/A2:2006)
Testing of protective coatings of printed circuit
boards carried out in accordance with IEC
60664-3 with the following modifications:
5.7
--N/A
---
Requirement Test
Cold
5.9
Additional tests
This subclause is not applicable
N/A
---
Verdict
ANNEX O (INFORMATIVE)
SELECTION AND SEQUENCE OF THE TESTS OF CLAUSE 30
N/A
--N/A
--N/A
---
(IEC/EN 60335-1/A2:2006)
ANNEX Q (INFORMATIVE)
SEQUENCE OF TESTS FOR THE EVALUATION OF ELECTRONIC
CIRCUITS (IEC/EN 60335-1/A2:2006)
---
Requirement Test
29.3
N/A
N/A
N/A
29.3.Z1
Z1
Result Remark
Verdict
TABLE: Minimum thickness for single layer accessible reinforced insulation (EN
60335-1/A12:2006)
Rated voltage
V
N/A
Overvoltage
category II
Overvoltage
category III
Verdict
< 50
0,01
0,04
0,1
N/A
0,1
0,3
0,6
N/A
0,3
0,6
1,2
N/A
Requirement Test
24
COMPONENTS
24.1.7
(Replacement:)
If the remote operation of the appliance is via a
telecommunication network, the relevant
standards for the telecommunication interface
circuitry in the appliance are EN 41003 and EN
60950-1:2006, Subclause 6.3.
Result Remark
Verdict
N/A
Clause
Requirement Test
19
ABNORMAL OPERATION
19.14
Modification:
Result Remark
Verdict
N/A
COMPONENTS
24.1
Replacement:
---
List of components
N/A
25
25.7
Modification:
N/A
Requirement Test
Verdict
ultraviolet radiation.
26
26.2
Modification:
N/A
Modification:
N/A
29.1
Replacement:
N/A
Modification:
N/A
Addition:
N/A
7.1
N/A
N/A
Requirement Test
Verdict
7.12.Z1
N/A
----
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
----
Requirement Test
Verdict
N/A
N/A
N/A
N/A
N/A
N/A
19.11.4.8
N/A
20.1
N/A
20.2
N/A
Moving parts directly involved in the function of the appliance which cannot be
made completely inaccessible shall be fitted with:
----
N/A
N/A
N/A
Clause
Requirement Test
21.1
N/A
22.ZE.1
N/A
22.ZE.2
N/A
N/A
22.ZE.3
N/A
22.ZE.4
N/A
N/A
N/A
N/A
N/A
N/A
22.ZE.5
Result Remark
Verdict
Requirement Test
Verdict
----
N/A
N/A
N/A
N/A
Adjustable guards restricting access to those areas of the moving parts strictly
necessary for the work shall be:
----
N/A
N/A
22.ZE.6
N/A
Annex ZF
Annex ZZ
P
N/A
Requirement Test
25
25.7
Add the following text after the last dash and before
the paragraph regarding "Supply cords for class III
appliances":
N/A
N/A
N/A
N/A
Their properties shall be at least those of crosslinked halogen-free compound sheathed cords
(code designation H07ZZ-F).
Add the following after EN 50366:
N/A
Annex ZC
Result Remark
Verdict
--
N/A
N/A
EN 50525-3-11
- Electric cables - Low voltage energy cables of
rated voltages up to and including 450/750 V (U0/U)
Part 3-11: Cables with special fire performance Flexible cables with halogen-free thermoplastic
insulation, and low emission of smoke
EN 50525-3-21
- Electric cables - Low voltage energy cables of
rated voltages up to and including 450/750 V
(U0/U) Part 3-21: Cables with special fire
performance - Flexible cables with halogen-free
crosslinked insulation, and low emission of
smoke
Replace footnote 3) by the following:
3) EN 50525 series, which is related to, but not
directly equivalent with the IEC 60227 series,
applies instead.
Replace footnote 4) by the following:
4) EN 50525 series, which is related to, but not
directly equivalent with the IEC 60245 series,
applies instead.
Requirement Test
7.1
(Addition:)
Result Remark
Verdict
N/A
11
HEATING
11.2
(Addition:)
except for fan coils where the flow rates and
liquid temperatures shall be the maximum
specified in the manufacturers instructions;
(EN 60335-2-40/A2:2009)
11.8
(Replacement:)
N/A
15
MOISTURE RESISTANCE
15.1
(Replacement:)
The motor-compressor is not operated and
detachable parts are removed during the tests
of 15.2 and 15.3. (EN 60335-2-40/A2:2009)
15.101
(Addition:)
Spillage test as specified, unless
(EN 60335-2-40/A2:2009)
N/A
N/A
19
ABNORMAL OPERATION
19.10.101
(Addition:)
N/A
N/A
Requirement Test
Verdict
(EN 60335-2-40/A2:2009)
19.14
N/A
N/A
(Amendment:)
(Addition:)
N/A
N/A
21
MECHANICAL STRENGTH
21.1
(Replacement:)
22
CONSTRUCTION
22.102
(Replacement:)
N/A
22.102.2
N/A
Requirement Test
Verdict
water thermostats.
(EN 60335-2-40/A2:2009)
22.102.3
N/A
N/A
Requirement Test
Result Remark
16
---
16,101
32
Verdict
---9
Maximum: 1,22 x 10
---End of Report---