Foam Latex Prosthetic Application Guide
Foam Latex Prosthetic Application Guide
Foam Latex Prosthetic Application Guide
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
ImpaQt FX
G U I D E
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
Table of Contents
Solid Rubber Masks vs. Foam Latex
List of Supplies
Choosing an Adhesive
Adding Shadows
10
Adding Highlights
10
Stippling
10
11
12
G U I D E
I N T R O D U C T I O N
I N T R O D U C T I O N
Always perform a skin test on a small area to make sure you dont have an allergic reaction to
any of the make-up products you are using.
Always follow the manufacturers directions that came with each product.
Always make sure you have enough solvent to remove the particular adhesive being used.
Never apply make-up when you are smoking or near an open flame source.
If make-up must be used on more than one person, certain safety standards must be
maintained. Use either disposable applicators or applicators that can be cleaned between
uses. Mascara should never be shared.
Disposable triangle applicator sponges are perfect for applying all base and rouge colors. For
individual use, a natural sea sponge is great because it can be washed and reused. Foam
sponges are great for body make-up; they have a large surface area and are easy to clean up
(use a grease-cutting soap).
Brushes must be cleaned after each use with a brush treatment cleaner. Small disposable
detail work can also be accomplished with disposable cotton swabs.
As a make-up artist, professional or amateur, it is your responsibility to learn about the chemical safety;
consult libraries, school chemistry departments. Request and read Material Safety Data Sheets
(MSDS). Before you work with a chemical, investigate its hazardous factors. Use precautions when
handling any chemicals. Consult local authorities on proper material disposal.
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
DISCLAIMER
Most of the items we sell are considered non-toxic. However, the responsibility for the safe use of any
product sold rests solely on the buyer or user. No warranty either expressed or implied is given and
ImpaQt FX assumes no liability for the use or misuse of any item purchased. All products should be
used as directed on the product container or packaging that came with the product. Always use proper
ventilation, safety glasses, chemical resistant gloves and common sense when working with hazardous
or suspected hazardous materials.
Discontinue using any product that causes irritation (redness, itching, burning, scaling, soreness, or
other symptoms). If symptoms persist, please see your doctor. If you are dissatisfied with any product
purchased from ImpaQt FX, you may return it for a refund or exchange within 15 days of the purchase
date. Our liability for a defective item will not exceed its replacement cost to us.
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
Make-up Supplies
Heres a list of additional items youll need to apply and remove your prosthetic
appliance.
List of Supplies
Optional
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
Choosing an Adhesive
A number of adhesives are available for attaching prosthetic appliances: Spirit Gum, Prosthetic
Adhesive (called Pro-aide or Pros-Aide), Liquid Latex, and Toupee Tape. Each is discussed in the section
that follows. We recommend that you use Spirit Gum or Pros-aide for attaching your prosthetic.
Spirit Gum
Spirit Gum is an adhesive solution made of gum and ether and is the most
common adhesive on the market. We recommend spirit gum over other
adhesives because it is forgiving if you make a mistake. Spirit Gum
Remover is needed to remove this adhesive.
Spirit Gum
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
Pro Adhesive
Toupee tape is double-sided tape and can be used if you dont like the feel of spirit gum, Pros-aide or
liquid latex on your skin. The tape tends to limit the movement of the prosthetic and is more likely to
come loose with perspiration, so we do not recommend it for attaching prosthetics. Toupee tape (or
medical tape) is stronger than the Scotch brand double-sided tape. Scotch tape isnt strong or sticky
enough to work with prosthetics.
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
Before you apply any adhesive, position the piece where it will be attached to be sure it will fit properly.
Full face prosthetics have been sized to fit most faces whether you are a man or woman. Because of the
rubber qualities, adjustments can be made by either gently stretching the piece if too small or pulling
upwards on the sides to reduce the area that it covers.
Some make-up artists will temporarily mark the edge of the foam piece by lightly powdering along
the edge of it while it is held in place.
Using Spirit Gum
If you are using spirit gum, using a small make-up brush, paint a liberal amount in the center of the area
that will be covered by the appliance. In the case of a full face appliance, start with the bridge and sides
of your nose. Next, using your finger, gently pat the wet spirit gum until it becomes tacky. If you
pat too long, it will lose its tackiness. Too short, and the solvents wont have enough time to evaporate.
When the spirit gum starts to get really sticky, position the foam over the painted area and press it down
gently, making sure it is aligned where you want it to be. Continue this technique, working your way
from the center to the edges of the appliance. Be sure you have applied adhesive to every part of your
skin underneath the appliance. If you dont, the wearers facial expression wont show through the foam
latex as well and perspiration could pool in these areas.
Work on small areas at a time, attaching the appliance little by little. Gently stretch the appliance as
needed to paint the adhesive on areas that may be harder to reach.
IMPORTANT: Use caution when working around the eyes! Apply the spirit gum sparingly so it
doesnt run into them.
Using Pros-aide
Using a small make-up brush, paint a thin coat of Pros-aide on the inside of the appliance and let it
almost completely dry (it will turn clear when dry). Be careful not to let the appliance fold over, since
the Pros-aide will stick to itself. Also paint a thin coat onto your skin where the appliance will be
positioned and let it s tart to dry. When both are almost dry, gently press the prosthetic into place,
starting from the center and working towards the edges. After the appliance is in place, press down
firmly to make sure it is securely attached.
Using Liquid Latex
Make sure your skin is clean and free from oils before you apply the liquid latex. Using a make-up
sponge, pat on a thin coat of latex on the inside of the appliance and onto the area of your skin where
the appliance will be attached. AVOID GETTING THE LATEX INTO YOUR HAIR,
7
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
INCLUDING YOUR EYEBROWS AND LASHES, since it is very difficult to remove from hair
when dry. When both are almost dry, gently press the prosthetic into place, starting from the center and
working towards the edges.
Apply a small amount of liquid latex to a stipple sponge. A stipple sponge will generally produce the
best results, since the texture of the sponge will produce a random and more natural looking surface.
Lightly pat on the latex, overlapping the edge of the appliance and skin by approximately on each
side. Continue to apply a thin coating of latex along the edge of the entire appliance. When the latex is
dry, the edge of the appliance should be blended into the skin. You may add more latex if needed, but
be sure the latex has dried in between coats or it could stick to itself and pull up. After the latex has
dried, apply a small amount of powder to remove the stickiness.
In a hurry? Use a hair dryer to shorten the dry time of the latex. Be careful when drying someone
elses skin so that you dont burn them! You can feel the heat of the dryer by keeping your free hand in
close proximity to the area you are drying.
Even if you are careful when applying the latex, hiding the edges can be challenging. If you can still
see an edge, you might be able to hide it by adding more texture to edge. For example, if you are
creating a zombie, you could press corn meal or coffee grounds along the edge before the latex has
dried. You could also flow a small amount of stage blood along the edge to hide it. Once make-up is
applied, the edge will be hidden.
Hiding an Edge Using Pros Aide Thickened with Cab-O-Sil
Pros aide thickened with Cab-O-Sil called Cabo-Patch or Makeup Bondo can be used to hide the
edges of an appliance. It is preferred over using liquid latex since you can reactivate the Pros aide with
99% alcohol. Cabo-Patch can be easily created by mixing Pros-Aide with Cab-O-Sil (fumed silica) or
translucent powder until a paste is achieved. Apply a small amount of the Cabo-Patch along the edge of
the appliance, blending it with the skin. You can also use a soft-bristled brush loaded with 99% alcohol
to feather the Cabo-Patch. Once dry, you may need to add more Cabo-Patch since Pros-Aide shrinks a
little as it dries. Since Pros-Aide is also very sticky, add a generous amount of translucent powder to any
of the Pros-Aide to remove the stickiness.
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
Applying Make-up
Learn how to apply make-up to your foam latex appliance.
This is the part of the make-up application where your character really comes to life. Finishing your
make-up application involves a few steps: applying a base color, adding shadows and highlights,
stippling, and powdering.
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
As you pat on the base color, make sure you apply make-up
about 2 inches beyond the appliance and all the way to the
hairline. If you dont, youre much more likely to see a line
where the appliance ends and the skin begins.
If youre applying a bald cap, you might consider using a Bald
Cap RMG Wheel from Graftobian.
Adding Shadows
With just a base color applied, you wont have any depth to
your make-up application until you add shadows and
highlights. By adding a variety of darker and lighter colors, youll create layers that give your make-up
depth.
Bald Cap Colors (RMG Wheel)
To add shadows, mix up some make-up that is two shades darker than the base color. Alternately, you
can choose a darker RMG color from the wheel if you have one. If you use a color that is too dark
relative to the base color, the exaggerated difference will likely not be very convincing or realistic. Look
to see where natural shadows will appear in deeper skin folds and wrinkles, eye sockets, sides of the
nose, underneath bones that protrude further out (such as cheek bones), underneath the chin and
cheeks, along the temples, and along the sides of the neck..
To see where natural shadows appear, try changing the angle of light so that shadows appear.
Apply the shadow color to not only the prosthetic, but the surrounding skin as well.
Apply the make-up with a small brush or sponge, feathering the shadow color into the base color from
the center of where the primary shadow appears. Feathering or softening of an edge can be achieved
by lightly patting an area with your finger or sponge.
Adding Highlights
Highlight colors should be 2 to 3 shades lighter than the base color. You can choose a lighter RMG
color from the wheel if you have one. Using a small brush or sponge, apply the highlight color to raised
areas that would naturally have more light for example, brows, cheek bones, the ridge of the nose,
forehead and the chin. Feather (soften) any edges by lightly patting the highlighted areas with your
finger or sponge. The next step is to further soften any hard edges of the make-up by stippling.
Stippling
Stippling is a technique that adds another important layer which creates more depth and realism to your
make-up application. Skin is naturally mottled (has spots), so we are trying to recreate this look using
this technique. Mix a color that is darker than the base color (such as the color you used for adding
shadows). Using a stipple sponge, gently pat on the make-up, creating another subtle texture layer.
10
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
Be careful not to overdo the stippling! Stop before you think youve stippled enough, since you can
always add more later if needed.
Now apply another stipple layer using a color that is lighter than the base color (such as the highlight
color you used earlier). Stippling takes some practice, but the results are worth the time invested.
You cant use too much setting powder, but if you use too little, the make-up can smear. Use a
generous amount of powder and make sure all the make-up areas are covered. Any excess powder may
be brushed off with a dry brush or even a damp paper towel or wash cloth. Dont wipe the make up
simply blot it gently.
11
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
Removing Make-up
Learn how to remove your foam latex appliance.
Removing the make-up and appliance is easy, but should be done carefully and without rushing so that
your foam latex appliance can be reused.
If you attached your appliance using Spirit Gum, youll want to use rubbing alcohol to remove the
prosthetic first. Spirit Gum remover contains mineral oil which will bloat the edges of your appliance
so if you do use it to remove the appliance, you wont be able to use it again. You can still use Spirit
Gum remover once the appliance is removed with rubbing alcohol.
Dip a cotton swab or small brush in rubbing alcohol. Beginning at the top edge of your appliance,
gently rub the tip or cotton swab or brush along the edge of the foam latex until it begins to loosen.
Gently lift off of the appliance a little at a time, working your way from one side of the appliance to the
other. Apply more alcohol as needed, but be careful not to get any in your eyes. After the appliance
has been removed, apply powder to the piece to remove any stickiness that may be left over. To
remove any left Spirit Gum from the skin, apply Spirit Gum remover to a cotton ball and gently rub
the area.
CAUTION! Never tear an appliance from the skin without soaking it first. It will hurt the wearer
and may injure their skin.
Pros-aide
Since Pros-aide is very sticky, it will take a little longer to remove. You can remove Pros-aide in several
ways.
Using Rubbing Alcohol
If you want to try to reuse your appliance, youll need to use alcohol to carefully remove it. Ideally, it
will be 99% Isopropyl Alcohol, also known as rubbing alcohol. Most of the rubbing alcohol from drug
stores is 70% or 91%. While 99% is recommended if you can get it (probably from a makeup store),
91% will work, just not as well. You will likely only get 2 to 3 uses of the appliance depending on how
thin the edges are, even if you are careful in removing it. Some customers have gotten over 10 reuses.
While this is unusual, its not impossible depending on the appliance.
To reuse your appliance, dip a brush in alcohol. Youll want to use a brush that you dont mind getting
frayed. Beginning at top edge of your appliance, use the brush to soak the edge of the appliance with
the alcohol until the edge of the foam latex starts to loosen. Gently lift off the appliance a little at a
time, working your way from one side of the appliance to the other. Since pros aide sticks to itself,
12
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
powder the appliance as you go, making sure the appliance is dry before you powder it. If an edge
folds over, use alcohol to release the edge. Do not pull on the edge without releasing it first or it will
tear. Once unfolded, let the alcohol dry, then powder the appliance.
CAUTION! If you are working above the wearers eye, avoid letting the alcohol run into their eyes
by catching any of the alcohol that runs down using a small cloth towel. Paper towels are not
recommended since the glue will make them sticky and theyll tear.
Put some powder in the bag itself, before you put the appliance in the bag. If some part of the
appliance does stick to the bag, apply a little 99% alcohol to loosen the appliance from the bag and
GENTLY detach it so you dont rip the appliance.
13
F O A M
L A T E X
P R O S T H E T I C S :
M A K E - U P
A P P L I C A T I O N
G U I D E
You can use mineral oil (baby oil), but the edges of the appliance will bloat and the appliance will likely
not be reusable. Youll also need to wash the appliance right away since the mineral tends to degrade
the foam over time. Dip a cotton swab or small brush in mineral oil. Beginning at the top edge of your
appliance, gently rub the cotton swab along the edge of the foam latex until it begins to loosen. Gently
lift off the appliance a little at a time, working your way from one side of the appliance to the other.
Using Pro Adhesive Remover
You can use Pro Adhesive Remover to remove the adhesive and appliance
from the skin, but because it has both alcohol and oil in it, the appliance edges
will bloat and you will likely not be able to reuse the appliance. We recommend
that you first remove the appliance using 99% rubbing alcohol, then use Pro
Adhesive Remover to remove any remaining adhesive on the skin. Youll also
need to be careful not to get any of the remover in the eyes of the wearer, since
it does contain alcohol.
1 4