PhysicsA2 OptionAstrophysics Telescopes
PhysicsA2 OptionAstrophysics Telescopes
PhysicsA2 OptionAstrophysics Telescopes
Chapter 1 Telescopes
1.1 Lenses
Learning objectives:
A converging lens makes parallel rays converge to a focus. The point where parallel rays are
focused to is called the principal focus or the focal point of the lens.
A diverging lens makes parallel rays diverge (i.e. spread out). The point where the rays
appear to come from is the principal focus or focal point of this type of lens.
In both cases, the distance from the lens to the principal focus is the focal length of the lens. In
this option, we consider the converging lens only.
Astrophysics
Note
The plane on each side of the lens perpendicular to the principal axis containing the principal
focus is called the focal plane.
With the object at different distances beyond the principal focus of the lens, the position
of the screen is adjusted until a clear image of the object is seen on the screen. The image is
described as a real image because it is formed on the screen where the light rays meet. If the
object is moved nearer the lens towards its principal focus, the screen must be moved further
from the lens to see a clear image. The nearer the object is to the lens, the larger the image is.
With the object nearer to the lens than the principal focus, a magnified image is formed.
The lens acts as a magnifying glass. But the image can only be seen when you look into the
lens from the other side to the object. The image is called a virtual image because it is
formed where the light rays appear to come from.
Ray diagrams
The position and nature of the image formed by a lens depends on the focal length of the lens and
the distance from the object to the lens.
If we know the focal length, f, and the object distance, u, we can find the position and nature of
the image by drawing a ray diagram to scale in which:
the lens is assumed to be thin so it can represented by a single line at which refraction takes
place
the straight line through the centre of the lens perpendicular to the lens is called the principal
axis
the principal focus F is marked on the principal axis at the same distance from the lens on
each side of the lens
the object is represented by an upright arrow as shown in Figure 3.
Note that the horizontal scale of the diagram must be chosen to enable you to fit the object, the
image and the lens on the diagram.
Astrophysics
To locate the tip of the image, three key construction rays from the tip of the object are drawn,
through the lens. The tip of the image is formed where these three rays meet. The image is real
and inverted.
1
2
3
Ray 1 is drawn parallel to the principal axis before the lens so it is refracted by the lens
through F.
Ray 2 is drawn through the lens at its centre without change of direction. This is because the
lens is thin and its surfaces are parallel to each other at the axis.
Ray 3 is drawn through F before the lens so it is refracted by the lens parallel to the axis.
Figure 4(a) and 4(b) show ray diagrams for the object at 2F and between F and 2F respectively.
The results for Figures 3 and 4 are described in the table below. Notice that the image is:
diminished in size when the object is beyond 2F as in Figure 3
the same size as the object when the object is at 2F as in Figure 4(a)
magnified when the object is between F and 2F as in Figure 4(b).
Astrophysics
Formation of a virtual image by a converging lens
The object must be between the lens and its principal focus, as shown in Figure 5. The image is
formed on the same side of the lens as the object.
Figure 5 shows that the image is virtual, upright and larger than the object. The image is on the
same side of the lens as the object and can only be seen by looking at it through the lens. This is
how a magnifying glass works.
If the object is placed in the focal plane, light rays from any point on the object are refracted by
the lens to form a parallel beam. A viewer looking at the object through the lens would therefore
see a virtual image of the object at infinity.
Object position
Image position
beyond 2F
2F
between F and 2F
<F
between F and 2F
2F
beyond 2F
same side as object
Nature
of
image
real
real
real
virtual
Magnified or
diminished
Upright or
inverted
Application
diminished
same size
magnified
magnified
inverted
inverted
inverted
upright
camera
inverter
projector
magnifying
lens
Note
The linear magnification of the image =
The image is said to be magnified if the image height is greater than the object height and
diminished if it is smaller.
Astrophysics
1 1 1
u v
f
Notes
1 Proof of the lens formula is not required for this specification.
2 When numerical values are substituted into the formula, the sign convention
real is positive; virtual is negative
is used for the object and image distances. The focal length, f, for a converging lens is always
assigned a positive value. A diverging lens is always assigned a negative value.
Worked example
An object is placed on the principal axis of a convex lens of focal length 150 mm at a distance of
200 mm from the centre of the lens.
a Calculate the image distance.
b State the properties of the image.
Solution
a f = +0.150 m, u = +0.200 mm
Using the lens formula
Hence
1
1
1
1 1 1
gives
0.200 v 0.150
u v
f
1
1
1
Therefore v = +0.600 m
b The image is real (because v is positive), inverted and magnified (because v > u).
Summary questions
1 a i Copy and complete the ray diagram in Figure 6 to show how a converging lens in a camera forms
an image of an object.
Astrophysics
Figure 6
ii State whether the image in Figure 6 is real or virtual, magnified or diminished, upright or
inverted.
b i Draw a ray diagram to show how a converging lens is used as a magnifying glass.
ii State whether the image in your diagram is real or virtual, magnified or diminished, upright or
inverted.
2 An object is placed on the principal axis of a thin converging lens at a distance of 400 mm from the
centre of the lens. The lens has a focal length of 150 mm.
a Draw a ray diagram to determine the distance from the image to the lens.
b State whether the image is:
i real or virtual
ii upright or inverted.
c Use the lens formula to check the accuracy of your ray diagram.
3 An object is placed on the principal axis of a thin converging lens at a distance of 100 mm from the
centre of the lens. The lens has a focal length of 150 mm.
a Draw a ray diagram to determine the distance from the image to the lens.
b State whether the image is:
i real or virtual
ii upright or inverted.
c Use the lens formula to check the accuracy of your ray diagram.
4 An object of height 10 mm is placed on the principal axis of a converging lens of focal length 0.200 m.
a Calculate the image distance and the height of the image for an object distance of:
i 0.150 m
ii 0.250 m.
b In each case above, calculate the distance between the object and the image and state whether the
image in each case is real or virtual and upright or inverted.
The linear magnification of the image =
Astrophysics
To understand why the viewer sees a magnified virtual image, consider the effect of each lens on
the light rays from the object that enter the telescope:
The objective lens focuses the light rays to form a real image of the object. This image is
formed in the same plane as the principal focus of the objective lens which is where the light
rays cross each other after passing through the objective lens. If a tracing paper screen is
placed at this position, as shown in Figure 2, the real image formed by the objective can be
seen directly on the paper without looking through the eyepiece.
Astrophysics
The eyepiece gives the viewer looking through the telescope a magnified view of this real
image with or without the tracing paper present. If the tracing paper is removed, the viewer
sees the same magnified view of the real image except much brighter. This magnified view is
a virtual image because it is formed where the rays emerging from the eyepiece appear to
have come from.
The virtual image is inverted compared with the distant object. This is because the real image
formed by the objective is inverted and the final virtual image is therefore inverted compared
with the distant object.
The ray diagram in Figure 3 shows in detail how the viewer looking through the eyepiece sees the
final virtual image. The diagram shows the telescope in normal adjustment which means the
telescope is adjusted so the virtual image seen by the viewer is at infinity. In this situation, the
principal focus of the eyepiece is at the same position as the principal focus of the objective. In
other words, in normal adjustment:
the distance between the two lenses is the sum of their focal lengths
This is because:
the real image of the distant object is formed in the focal plane of the objective (because the
light rays from each point of the object are parallel to each other before entering the objective
lens)
the eyepiece is adjusted so its focal plane coincides with the focal plane of the objective. As a
result, the light rays that form each point of the real image leave the eyepiece parallel to one
another. To the viewer looking into the eyepiece, these rays appear to come from a virtual
image at infinity.
Astrophysics
Notes
1 The light rays from each point of the distant object:
are effectively parallel to each other by the time they reach the telescope
leave the telescope as a parallel beam which therefore appears to the viewer to come from
a distant point.
2 The real image formed by the objective lens is inverted and diminished in size. The eyepiece
in effect acts as a magnifying glass with the real image being viewed by it. The viewer sees a
magnified virtual image which is upright compared with the real image and therefore
inverted compared with the distant object.
3 Notice that all the light rays from the object that pass through the eyepiece all pass through a
circle referred to as the eye-ring. This is the best position for the viewers eye as the entire
image can be seen by the eye at this position.
Angular magnification
Application
Investigating the simple refracting telescope
Use two suitable converging lenses in holders to make a simple refracting telescope. Adjust the
position of the eyepiece so an image of a distant object is seen in focus. The image of the object is
inverted and it should be magnified.
Place a tracing paper screen between the lenses and locate the real image of the distant object
formed by the objective lens. Observe the image directly and through the eyepiece to see that the
eyepiece gives a magnified virtual image of the real image. The virtual image becomes brighter if
the screen is removed.
View the distant object directly with one eye and through the telescope with the other eye, as in
Figure 4. You should be able to estimate how large the image appears to be compared with the
object viewed directly (i.e. without the aid of the telescope). This comparison is referred to as the
angular magnification (or magnifying power) of the telescope.
Suppose a telescope in normal adjustment makes a distant object appear to be three times larger.
Its angular magnification would therefore be 3. If the angle subtended by the distant object to the
unaided eye is 1, the angle subtended by the telescope image to the eye would be 3. Figure 5
shows the idea. The diagram shows only one light ray from the top of the object entering the
Astrophysics
telescope at the objective lens and leaving in a direction as if it was from the tip of the virtual
image seen by the viewer. The distant object and the image are meant to be at infinity so the angle
subtended by the distant object to the unaided eye is effectively the same as the angle subtended
by the object to the telescope.
The angle subtended by the final image at infinity to the viewer =
The angle subtended by the distant object to the unaided eye =
The angular magnification of the telescope in normal adjustment =
h
h1
and tan = 1 , where h1 is the
fo
fe
height of the real image and fo and fe are the focal lengths of the objective and eyepiece lenses
respectively.
h1
fe fo
tan
Combining these two equations to eliminate h1 gives
h
tan
fe
1
fo
Assuming angles and are always less than about 10, applying the small angle approximation
tan = in radians and tan = in radians gives
fo
fe
Therefore:
10
Astrophysics
the angular magnification of a telescope in normal adjustment =
fo
fe
Notes
1 The height h1 of the real image = fo tan = fo ( in radians)
Remember 360 = 2 radians.
2 The objective is the lens with the longer focal length. If you use a telescope the wrong way
round, you will see a diminished image!
Worked example
A refracting telescope consists of two converging lenses of focal lengths 0.840 m and 0.120 m.
a If the telescope is used in normal adjustment, calculate:
i
ii the diameter of the real image of the lunar disc formed by the objective lens.
Solution
a i
f o 0.840
7.0
f e 0.120
angular magnification =
where = 0.40
Image brightness
A star is so far away that it is effectively a point object. When viewed through a telescope, a star
appears brighter than when it is viewed by the unaided eye. This is because the telescope
objective is wider than the pupil of the eye so more light from a star enters the eye when a
telescope is used than when the eye is unaided.
The pupil of the eye in darkness has a diameter of about 10 mm. The light entering the eye pupil
or the objective is proportional to the area in each case and the area is proportional to the square
11
Astrophysics
of the diameter. Therefore, in comparison with the unaided eye, a telescope with an objective
lens:
60 2
of diameter 60 mm would collect 36 times more light per second from a star
10
120 2
of diameter 120 mm would collect 144 times
more light per second from a star.
10
This is why many more stars are seen using a telescope than using the unaided eye. The greater
the diameter of the objective of a telescope, the greater the number of stars that can be seen.
Planets and other astronomical objects in the solar system are magnified using a telescope (unlike
stars which are point objects and are seen through telescopes as point images no matter how large
the magnification of the telescope is). Yet the image of a planet viewed using a telescope is not
significantly brighter than the planet when it is viewed directly. This is because, although more
light per second enters the eye when a telescope is used, the virtual image is magnified so is
spread over a larger part of the field of view. As a result, the amount of light per second per unit
area of the virtual image is unchanged.
Warning! Never view the Sun using a telescope or directly. The intensity of sunlight
entering the eye would damage the retina of the eye and cause blindness.
12
Astrophysics
Figure 6 Galileo
Summary questions
1 Draw a ray diagram of a telescope consisting of two converging lenses to show how an image is formed
of a distant object. Show clearly on your ray diagram the principal focus of the lenses, the position of
the viewers eye and label the two lenses.
2 A telescope consists of two converging lenses of focal lengths 60 mm and 450 mm. It is used in normal
adjustment to view a distant object that subtends an angle of 0.15 to the telescope.
a Explain what is meant by the term normal adjustment.
b Calculate:
i the angular magnification of the telescope
ii the angle subtended by the virtual image seen by the viewer.
3 Explain the following observations made using a telescope.
a A star too faint to see with the unaided eye is visible using the telescope.
b The Galilean moons of Jupiter can be observed using a telescope but not by the unaided eye.
4 A telescope consisting of two converging lenses has an eyepiece of focal length 40 mm. When used in
normal adjustment, the angular magnification of the telescope is 16.
a Calculate:
i the focal length of the objective lens
ii the separation of the two lenses.
b The image of a tower of height 75 m viewed through the telescope subtends an angle of 4.8 to the
viewer. Calculate:
i the angle subtended by the tower to the viewers unaided eye
ii the distance from the tower to the viewer.
13
Astrophysics
In a Cassegrain reflecting telescope, the secondary mirror is a convex mirror positioned near the
focal point of the primary mirror between this point and the primary mirror itself. The purpose of
the convex mirror is to focus the light onto or just behind a small hole at the centre of the concave
reflector. The light passing through this small hole then passes through the eyepiece which is
behind the concave mirror centre, as shown in Figure 2. The distance from the concave mirror to
the point where it focuses parallel rays is increased by using a convex mirror instead of a plane
mirror as the secondary mirror. This distance is the effective focal length of the objective.
14
Astrophysics
When the telescope is directed at a distant object, a viewer looking into the eyepiece sees a virtual
image of the distant object. The light from the distant object is:
1
2
3
15
Astrophysics
Also, a wide lens would be much heavier than a wide mirror and would make the telescope topheavy.
Further comparisons between refractors and reflectors are summarised below.
Refracting telescopes:
use lenses only and do not contain secondary mirrors and supporting frames which would
otherwise block out some of the light from the object
have a wider field of view than reflectors of the same length because their angular
magnification is less. Astronomical objects are therefore easier to locate using a refractor
instead of a reflector of the same length.
Reflecting telescopes:
are shorter and therefore easier to handle than refractors with the same angular magnification
have greater angular magnification than refractors of the same length and therefore produce
greater magnification of distant objects such as the Moon and the planets.
Summary questions
1 Draw a ray diagram to show the passage of light from a distant point object through a Cassegrain
reflecting telescope. Show the position of the eye of the observer on your diagram and label the parts
that make up the telescope and the effective focal point of the objective.
2 a State what is meant by chromatic aberration.
16
Astrophysics
b Explain why the objective of a refracting telescope produces chromatic aberration whereas that of a
Cassegrain reflector does not.
3 State and explain one disadvantage and one advantage, other than reduced chromatic aberration, a
Cassegrain telescope has in comparison with a simple refractor telescope.
4 A Cassegrain telescope has a primary mirror of diameter 80 mm.
a Calculate the ratio of the light energy per second it collects to the light energy per second collected
by the eye when the eye pupil is 8 mm in diameter.
b The telescope objective has an effective focal length of 2.8 m and its eyepiece has a focal length of
0.07 m. Calculate its angular magnification.
17
Astrophysics
Diffraction
The extent of the detail that can be seen in a telescope image depends on the width of the
objective. Imagine viewing two stars near each other in the night sky. The angular separation of
the two stars is the angle between the straight lines from the Earth to each star, as shown in
Figure 1.
Suppose the two stars are viewed through a telescope and their images can just be seen as
separate images. In other words, the telescope just resolves the two stars. If the telescope is
replaced by one with a narrower objective, the images of the two stars would overlap too much
and the observer would not be able to see them as separate stars. This is because:
the objective lens or mirror is in an aperture (i.e. a gap) which light from the object must pass
through and diffraction of light always occurs whenever light passes through an aperture
instead of focusing light from a star (or other point object) to a point image, diffraction of
light passing through the objective causes the image to spread out slightly.
the narrower the objective, the greater the amount of diffraction that occurs when light passes
through the narrower objective. So the greater the spread of the image.
18
Astrophysics
For light of wavelength passing through a circular aperture of diameter D, it can be shown that
an approximate value of the angle of diffraction, in radians, of the first dark ring is given by
.
D
Link
Topic 13.6 of AS Physics A looks at single slit diffraction.
Prove for yourself that, for an objective of diameter 80 mm , the angle of diffraction for the first
dark ring is approximately 6.3 106 radians (= 0.00036 degrees) for light of wavelength 500 nm.
In comparison, the corresponding angle for an objective of diameter 20 mm would be four times
larger (i.e. 0.0014(4) degrees).
D
where = the wavelength of light, and D = the diameter of the circular aperture.
19
Astrophysics
For example, a telescope with an 80 mm diameter objective will just be able to resolve two stars
with an angular separation of 0.000 36 degrees, assuming an average value of 500 nm for the
wavelength of light. Without the telescope, the human eye would not be able to resolve them as
the typical eye pupil diameter is about 8 mm which is a tenth of the width of an 80 mm wide
telescope. The unaided eye can resolve two stars only if their angular separation is at least 0.0036
degrees (i.e. ten times greater than that with an 80 mm wide telescope).
Notes
1 Resolution or resolving power are both used sometimes to describe the quality of a
telescope in terms of the minimum angular separation it can achieve. For example, a
telescope described as having a resolution or resolving power of 0.004 degrees can resolve
two stars which have an angular separation of at least 0.004 degrees.
2 The Rayleigh criterion applies to the detail visible in extended images as well as to stars. For
example, a telescope with a resolving power of 5 105 radians (= 0.003 degrees) is capable
of seeing craters on the lunar surface which have an angular diameter of 0.003 degrees. As
the Moon is about 380 000 km from Earth, such craters are about 20 km in diameter.
3 Refraction due to movement of air in the atmosphere causes the image of any star seen
through a telescope to be smudged slightly. As a result, ground-based telescopes with
objectives of diameter greater than about 100 mm do not achieve their theoretical resolution.
20
Astrophysics
The stunning clarity of images from the Hubble Space Telescope is because the telescope has
an objective mirror of diameter 2.4 m and is above the atmosphere and therefore does not
suffer from atmospheric refraction. Hence it achieves its theoretical resolution which is about
240 times greater than that of a 100 mm wide telescope.
Summary questions
1 a What is the name for the physical phenomenon that causes the image formed by a lens or mirror of a
point object to be spread out?
b i Sketch the pattern of the image of a distant point object formed by a lens.
ii Describe how the pattern would differ if a wider lens of the same focal length had been used?
2 State and explain what is meant by the Rayleigh criterion for resolving two point objects using a
telescope.
3 Two stars have an angular separation of 8.0 106 rad.
a Assuming light from them has an average wavelength of 500 nm, calculate an approximate value for
the diameter of the objective of a telescope that can just resolve the two stars.
b Discuss how the image of the two stars would differ if they were viewed with a telescope with an
objective of twice the diameter and the same angular magnification.
4 The Hubble Space Telescope has an objective of diameter 2.4 m.
a Show that the theoretical resolution of the HST is 1.2 105 degrees.
b Hence estimate the diameter of the smallest crater on the Moon that can be seen using the telescope.
Assume the wavelength of light is 500 nm.
EarthMoon distance = 3.8 108 m
21
Astrophysics
Charge-coupled devices
Astronomers have always used photographic film to capture images ever since photography was
first invented in the 19th century. However, the charge-coupled device invented in the late 20th
century fitted to a telescope has dramatically extended the range of astronomical objects that can
be seen as well as providing images of stunning quality.
Figure 1 Using a CCD (a) A CCD in a telescope (b) A CCD image of a spiral galaxy
The CCD is an array of light-sensitive pixels which become charged when exposed to light. After
being exposed to light for a pre-set time, the array is connected to an electronic circuit which
transfers the charge collected by each pixel in sequence to an output electrode connected to a
capacitor. The voltage of the output electrode is read out electronically then the capacitor is
discharged before the next pulse of charge is received. In this way, the output electrode produces
a stream of voltage pulses, each one of amplitude in proportion to the light energy received by an
individual pixel. Figure 2 shows part of an array of pixels.
22
Astrophysics
Each pixel has three small rectangular metal electrodes (labelled A, B and C in Figure 2) which
are separated by a thin insulating layer of silicon dioxide from p-type silicon which is the lightsensitive material underneath. The electrodes are connected to three voltage supply rails.
The rectangular electrodes and the insulating layer are thin enough to allow light photons to
pass through and each liberate an individual electron in the light-sensitive material
underneath.
When collecting charge, the central electrode in each pixel (labelled B in Figure 2) is held at
+10 V and the two outer electrodes at +2 V. This ensures the liberated electrons accumulate
under the central electrode.
After the pixels have collected charge for a certain time, the charge of each pixel is shifted
towards the output electrode via the adjacent pixels. This is achieved by altering the voltage
level of each electrode in a sequence of three-step cycles, as shown in Figure 2.
The quantum efficiency of a pixel is the percentage of incident photons that liberate an electron.
About 70% of the photons incident on a pixel each liberates an electron. Therefore, the quantum
efficiency of a pixel is about 70%. In comparison, the grains of a photographic film have a
quantum efficiency of about 4% as only about 4 in every 100 incident photons contributes to the
darkening of each grain. So a CCD is much more efficient than a photographic film and hence it
will detect much fainter astronomical images than a film.
23
Astrophysics
otherwise random emission of electrons causes a dark current which does not depend on the
intensity of light.
Radio telescopes
Single-dish radio telescopes each consist of a large parabolic dish with an aerial at the focal point
of the dish. A steerable dish can be directed at any astronomical source of radio waves in the sky.
The atmosphere transmits radio waves in the wavelength range from about 0.001 m to about 10 m.
When the dish is directed at an astronomical source that emits radio waves in the above
wavelength range, the waves reflect from the dish onto the aerial to produce a signal. The dish is
turned by motors to enable it to scan sources and to compensate for the Earths rotation.
The amplitude of the signal is a measure of the intensity of the radio waves received by the dish.
The signal from the aerial is amplified and supplied to a computer for analysis and recording. As
the dish scans across the source, the signal is used to map the intensity of the radio waves across
the source to give a radio image of the source.
The dish surface usually consists of a wire mesh which is lighter than metal sheets and just as
effective in terms of reflection, provided the mesh spacing is less than about
20
, where is the
1
4
D2)
)
D
The Lovell radio telescope at Jodrell Bank in Cheshire has a 76 m steerable dish which gives a
resolution of 0.2 degree for 21 cm wavelength radio waves. In comparison, the Arecibo radio
telescope in Puerto Rica is a 300 m fixed concave dish set in a natural bowl. As it is four times
wider than the Lovell telescope, it can therefore resolve radio images to about 0.05 degrees
(= 14 of 0.2) and detect radio source 16 times fainter (as it collects 16 times as much radio
24
Astrophysics
energy per second than the Lovell telescope does). However, the Arecibo telescope can only
detect radio sources when they are close to its principal axis.
Link
Electromagnetic waves were looked at in Topic 1.3 of
AS Physics A.
Infrared telescopes
Infrared telescopes have a large concave reflector which focuses infrared radiation onto an
infrared detector at the focal point of the reflector. Objects in space such as planets that are not
hot enough to emit light emit infrared radiation. In addition, dust clouds in space emit infrared
radiation. Infrared telescopes can therefore provide images from objects in space that cannot be
seen using optical telescopes.
25
Astrophysics
The Hubble Space Telescope with its objective at 2.4 m wide is capable of detecting infrared
wavelengths from 700 nm to about 1000 nm (= 0.001 mm). It can form images of warm objects
such as dying stars and planets in other solar systems that emit thermal radiation but not light.
Ultraviolet telescopes
Ultraviolet (UV) telescopes must be carried on satellites because UV radiation is absorbed by the
Earths atmosphere. As UV radiation is also absorbed by glass, a UV telescope uses mirrors to
focus incoming UV radiation onto a UV detector. UV radiation is emitted by atoms at high
temperatures, so UV telescopes are used to map hot gas clouds near stars and to study hot objects
in space such as glowing comets, supernova and quasars. Comparing a UV image of an object
with an optical or infrared image gives useful information about hot spots in the object.
The International Ultraviolet Explorer (IEU) launched in 1978 carried a 0.45 m wide
Cassegrain telescope with a UV detector instead of an eyepiece in its focal plane.
The Hubble Space Telescope uses a CCD to detect images at wavelengths from 115 nm to
about 1000 nm, giving ultraviolet images as well as visible and infrared images according to
the filters used over the CCD.
The XMM-Newton space observatory, launched in 1999 and still in operation, carries a 30 cm
wide modified Cassegrain reflector fitted with a detector with a wavelength range from
170 nm to 650 nm. So, it can give ultraviolet as well as optical images.
Figure 4 A combined UV and optical image of the galaxy M82 galaxy (UV in blue).
26
Astrophysics
International Gamma Ray Astrophysics Laboratory (INTEGRAL) launched in 2002 is being used
to study supernova, gamma ray bursts and black holes. As gamma rays and X-rays are very short
wavelength, diffraction is insignificant and image resolution is determined by the pixel
separation.
Summary questions
The table below is an incomplete comparison of different types of astronomical telescopes.
Type
Location
optical
ground or
satellite
radio
ground
Wavelength
range
350650 nm
Resolution
(degrees)
5
10 for HST
1 mm to 10 m
0.2 for
Lovell
infrared
Key advantages
Major disadvantages
ground telescopes
suffer from
atmospheric refraction
ultraviolet
X and
gamma
0.2 for
INTEGRAL
large, supporting
structure needed for a
steerable dish.
mirror needs to be
cooled
1 Copy this table and use the information in this topic to complete columns 2 and 3.
2 a Use the information in the previous pages to estimate the resolution in degrees of:
i HST at a wavelength of 0.001 mm
ii XMM-Newton at a wavelength of 170 nm
b Use your estimates to complete column 4 of your table.
3 Complete column 5 by giving two key advantages of:
a UV telescopes
b X-ray and gamma ray telescopes.
4 The collecting power of a telescope is a measure of how much energy per second it collects. This
depends on the area of its objective as well as the power per unit area (intensity) of the incident
radiation.
a For the same incident power per unit area, list the following telescopes in order of their collecting
power:
Hubble Space Telescope (2.4 m in diameter)
INTEGRAL (0.60 m diameter)
IRAS (0.60 m diameter)
Lovell telescope (76 m diameter)
XMM-Newton (0.30 m diameter)
b The Lovell radio telescope is linked to other radio telescopes in England so they act together as an
effective radio telescope of much greater width. Discuss without calculations how the resolving
power and the collecting power of the linked system compare with that of the Lovell telescope on its
own.
27