1. The document provides instructions for updating the operating software on a BZ 500 LSN/BE 500 security system. It outlines the necessary steps, including downloading the required software files, burning them to EPROMs, replacing the EPROMs on the relevant circuit boards, and using an update program on a connected PC to transfer the software files.
2. The update must be performed in a specific order, first updating any ERLE 10 boards, then the ZALE 10 board, and then any BE 500 boards. Status messages are displayed on the BZ 500 and PC during the transfer process.
3. Troubleshooting steps are provided in case the transfer fails or is interrupted, which involve restarting the
1. The document provides instructions for updating the operating software on a BZ 500 LSN/BE 500 security system. It outlines the necessary steps, including downloading the required software files, burning them to EPROMs, replacing the EPROMs on the relevant circuit boards, and using an update program on a connected PC to transfer the software files.
2. The update must be performed in a specific order, first updating any ERLE 10 boards, then the ZALE 10 board, and then any BE 500 boards. Status messages are displayed on the BZ 500 and PC during the transfer process.
3. Troubleshooting steps are provided in case the transfer fails or is interrupted, which involve restarting the
1. The document provides instructions for updating the operating software on a BZ 500 LSN/BE 500 security system. It outlines the necessary steps, including downloading the required software files, burning them to EPROMs, replacing the EPROMs on the relevant circuit boards, and using an update program on a connected PC to transfer the software files.
2. The update must be performed in a specific order, first updating any ERLE 10 boards, then the ZALE 10 board, and then any BE 500 boards. Status messages are displayed on the BZ 500 and PC during the transfer process.
3. Troubleshooting steps are provided in case the transfer fails or is interrupted, which involve restarting the
1. The document provides instructions for updating the operating software on a BZ 500 LSN/BE 500 security system. It outlines the necessary steps, including downloading the required software files, burning them to EPROMs, replacing the EPROMs on the relevant circuit boards, and using an update program on a connected PC to transfer the software files.
2. The update must be performed in a specific order, first updating any ERLE 10 boards, then the ZALE 10 board, and then any BE 500 boards. Status messages are displayed on the BZ 500 and PC during the transfer process.
3. Troubleshooting steps are provided in case the transfer fails or is interrupted, which involve restarting the
4.998.139.406 Operating software update for BZ 500 LSN / BE 500 D Download required software from mailbox of Bosch Security Systems Infomanagement: BootpromSW fr ZALE/ERLE/BEB Stand: xx (CS XXXX), from version 2.20 up ASUPProgramm fr BZ 500 Update, Version 2.xx, from version 2.1 up ZALE10 AnlagenSW fr BZ 500 A.xx (HEXMIN F., CS XXXX), from v. 3.30 up .Follow this programming order: 1. ERLE 10 2. ZALE 10 3. BE 500 (by OVS). D Burn Bootpromsoftware onto the Boot EPROM (checksum see titling of SWversion) and label EPROM (see picture). .Each ERLE, ERSE and/or BE 500 being instal- led requires one more BootEPROM. D Take off cover of BZ 500, remove jumper ANLAGE EIN (on ANNE 10) and exchange EPROM(s): on ZALE 10 on ERLE 10 (if installed) on ERSE 10 (if installed) D If a BE 500 is installed remove cover and exchange EPROM on the BEB10 circuit board as well. D Install ASUPProgramm fr BZ 500 Update, Version 2.xx on PC / laptop (extract ZIPfile). D Copy system software (ZALE10 Anlagen SW...) to C:\ Programm\ ASUP 2.xxx\Hex\ BZ500\V0000. .Preset interface for data transfer is COM1 (see OPTIONEN / COM SCHNITTSTELLE of ASUP2.x). If your PC / laptop uses a different interface for data transfer change setting (e.g. COM2). D Connect BZ 500 and PC / laptop with a V24(RS232)interface cable. PC on ANNE 10 (at BZ 500) with COM 1 (or COM2) at PC / laptop. D Set jumper PROGRAMM DOWN LOAD (on ANNE 10) to EIN (only required for first software update). D Power up BZ 500 by setting the jumper on ANLAGE EIN (on ANNE10) . Rear view of front panel (loaded with all options) ANNE 10 3.802.191.612 BZ 500 / BE 500 UPDATE V2.2 CS: XXXX ZALE / IC 73 ERLE / IC 57 BZ/BE 500 LSN Software Update Instruction Manual A1.en / 21.02. 2003 ST / PMB / zab 2 4.998.139.406 D Execute file ASUP.EXE on PC / laptop. The software update program ASUP starts scanning the configuration (onscreen mes- sage [Konfigurationsabfrage. . .]). Thereafter the configuration of BZ 500 is dis- played (see picture). D Click on file [bzxxxd.hex] within left window (1.) and on destination file within right window (2.): [ERLE ] for update of ERLE10 [BZ500] for update of ZALE10 D After that click on [Update Anlagen-SW] (3.). The settings of software transfer data are dis- played asking: Are you sure you want to start system software update? D Click [OK] for confirmation (4.). During transfer time the message [Software Download: Start BootEPROM] is shown on the BZ 500 display. All LEDs are flashing. Transfer progress in % is displayed on PC / laptop. The data transfer lasts 8 minutes approx.. A successful data transfer will be notified by the message [Erfolgreich beendet]. D Click [OK] for confirmation. D A software update of ZALE 10 (if installed) is carried out by according procedure. Just choose [BZ500] for configuration (see picture on top, step 2.). 1. 2. 3. 4. 5. BZ500 ERLE ungltig ZALE [1] ERLE [1] ERSE [1] BZ/BE 500 LSN Software Update Instruction Manual A1.en / 21.02. 2003 ST / PMB / zab 3 4.998.139.406 D After successful data transfer reset jumper PROGRAMM DOWN LOAD (on ANNE 10) to AUS. D Remove and replace jumper ANLAGE EIN to restart the BZ 500 (only required for first software update). When restarting the BZ 500 date and time in- put must be done. Thereafter the current ope- rating software version is displayed. .A software update of a BE 500 is carried out accordingly. For data transfer to BE 500 an OVS is required. Troubleshooting for Software Update D If the central unit does not return to normal operating condition due to failing data transfer or update break off, set jumper PROGRAMM DOWN LOAD (on ANNE 10) to EIN and restart update procedure. D Reset jumper PROGRAMM DOWN LOAD (on ANNE 10) to AUS after successful data transfer. ANNE 10