Complete 3909&3910

MACHINE SERIAL NO.
3909,3910 & 3911

INSTRUCTION AND SERVICE MANUAL

FOR THE

M-800 HK/PR W/ BAO 5000E

PLASTIC BOTTLE FEEDING SYSTEM

BUILT FOR:

COLGATE
COLUMBIA

NOTE: THE GRAPHICS IN THIS MANUAL ARE FOR ILLUSRTATIVE PURPOSES ONLY
AND MAY NOT BE IDENTICAL TO THE MACHINE THAT YOU HAVE PURCHASED.

PACE PACKAGING CORPORATION
3 SPERRY ROAD
FAIRFIELD , NEW J ERSEY 07004
9/18/13
PHONE: (973) 227-1040

Page 1 / 170
PACE MACHINES
BOTTLE FLOW
SERIAL # 3909
UNSCRAMBLER
SERIAL # 3910
BAO 5000E
Page 2 / 170
TABLE OF CONTENTS

SPECIFICATION Section I (PG. 4)

INTRODUCTION Section II (PG. 5)

FUNCTIONAL DESCRIPTION Section III (PG. 6)
GENERAL
BULK HOPPER
UNSCRAMBLER
CENTRIFUGAL DISC
STAND-UP UNIT (SUU)
BAO 5000E
ELECTRICAL

INSTALLATION REQUIREMENTS Section IV (PG. 9)

TROUBLESHOOTING GUIDE Section V (PG. 12)

MAINTENANCE Section VI (PG. 13)

HOPPER BELT REPLACEMENT

BELTS

URETHANE TWIN A BELTS
BELT CLEANING
BELT LUBRICATION
BELT INSTALL

SOFT CLOTH COVERED BELTS
BELT CLEANING
BELT LUBRICATION
BELT INSTALL

LUBRICATION
ELECTRICAL

SET-UP SPECIFICATION DIAGRAMS Section VII (PG. 27)

SPARE PARTS LIST Section VIII (PG. 92)

ELECTRICAL SPECIFICATIONS Section IX (PG. 100)
SCHEMATIC
ELECTRICAL BILL OF MATERIALS

********************************************************************************
NOTICE
IT IS ESSENTIAL THAT THIS MANUAL BE READ AND UNDERSTOOD BY QUALIFIED
PERSONNEL BEFORE INSTALLATION OR START UP OF EQUIPMENT BEGINS.

********************************************************************************
SECTION I PACE PACKAGING CORPORATION

SPECIFICATION
PACE UNSCRAMBLER MODEL NO. : M 800
PACE UNSCRAMBLER SERIAL NO. : 3909
PACE BAO MODEL NO. : BAO 5000E
PACE BAO SERIAL NO. : 3910
PACE HOPPER MODEL NO. : 170 CU FT
PACE HOPPER SERIAL NO. : 3911
PACE AIR CLEANER MODEL NO. : McBRADY ORBIT 200
PACE AIR CLEANER SERIAL NO. : 2777

POWER REQUIREMENTS:

COMPRESSED AIR REQUIREMENT:

This unit has been prepared to unscramble plastic containers only. The type, size, and
speed(s) are indicated below.
VOLTAGE PHASE FREQUENCY AMP.
400 VAC 3 60 Hz

PRESSURE VOLUME
US 80 PSI 8.25 CFM
METRIC 5.51 BARS .234 CU.M.

CONTAINERS
NO. SIZE STYLE MATERIAL RATE
1 850 ml Suavizante Oval HDPE 290 bpm

Page 4 / 170

SECTION II PACE PACKAGING CORPORATION

THE PACESETTER PLASTIC BOTTLE UNSCRAMBLING SYSTEM

Model M-800 & BAO 5000E

******************************************************************
N O T I C E
IT IS ESSENTIAL THAT THIS MANUAL BE READ AND UNDERSTOOD BEFORE
INSTALLATION OR START UP OF EQUIPMENT BEGINS.

THE PICTURES AND FIGURES IN THIS MANUAL ARE FOR ILLUSTRATIVE
PURPOSES ONLY. THE CUSTOMERS MACHINE MAY BE CONFIGURED
DIFFERENTLY THAN ACTUALLY SHOWN IN THE MANUAL.
******************************************************************

INTRODUCTION

The Pacesetter Plastic Bottle Unscrambling System is a very compact and flexible System that
takes a wide range of plastic bottles from a random, scrambled condition and places them on a
conveyor in an organized manner.

This manual describes the three major System modules available. They are:
* Bulk Hopper
* Unscrambler
* Bottle Axial Orientor

Your System may have some or all of these modules.

This manual provides the information required for maximum efficiency of your System. The
manual should be read thoroughly and the illustrations should be studied carefully by all
personnel involved in installing, operating, and maintaining the System.

A Pace Packaging Corporation (Pace) serviceman is available to assist with installation and
training. Arrangements for service should be made directly with Pace. Prior to a start up
service visit, the System should be positioned in its permanent location and connected to the
factory air and electric facilities. Further, the list of recommended spare parts should be on
hand during start up.

Warning
All operators must be properly trained in the use of this equipment.

Page 5 / 170

SECTION III PACE PACKAGING CORPORATION

FUNCTIONAL DESCRIPTION

GENERAL

Randomly oriented bottles are received in bulk into the hopper and supplied to the centrifugal disc
by means of a conveyor. In the disc, the bottles are guided into a qualified position (e.g., single
stream, either neck leading or base leading) suitable for the stand up unit to process them into the
required discharge position (e.g., standing; horizontal, base leading; horizontal, neck leading).
Symmetrical bottles are stabilized and released on the customer conveyor.

BULK HOPPER

The bulk hopper stores a supply of bottles and feeds them to the centrifugal disc by means of a
conveyor with cleats. The speed of the conveyor drive motor is adjustable by means of a
potentiometer located within the electrical enclosure. The start-stop action of the motor is
controlled by a sensor mounted next to the disc. It controls the level of bottles on the disc.

The bulk hopper requires no change parts for proper operation with differing shapes or sizes of
bottles. However, the recommended operating speed may change as noted in Section VII - Set Up
Instructions.

Warning

Care must be taken over the following:
1. Loading the bottles in the hopper must be possible without exceeding normal ergonomic
requirements. A suitable platform may be needed.
2. Do not enter hopper during operation. The hopper conveyor could be damaged and injury may
result.
3. Observe the location of support legs to avoid tripping and possible injury.

CENTRIFUGAL DISC

The disc receives bottles in random orientation from the hopper and, by means of centrifugal
action, guides the bottles into a grove on the outer edge of the disc. From this groove bottles are
fed into the stand up unit.

The design of the rotating tooling disc is determined by the size and shape of bottles to be
unscrambled, and by the feed rate required.

Whenever more than one size and/or shape of bottles are to be unscrambled, the disc is designed to
be adapted to the different bottles by means of disc inserts (rings).

A rotary bumper rejects excess flow of bottles not properly qualified in the disc groove, from
entering the stand up unit.

The speed of disc drive motor is adjustable by a potentiometer located in the main electrical
enclosure. The speed of the disc and the hopper conveyor, as well as the action of the disc level
sensor, should be adjusted to provide a controlled, even flow of bottles into the stand up unit.

Page 6 / 170


STAND UP UNIT

The design of the stand up unit incorporates several features which enable a Pace Unscrambler to
be adjusted, with a minimum of time for changeover, for different sizes and shapes of bottles.

In general, the stand up unit performs the following functions:

A. Receive qualified bottles (single stream of neck or base leading bottles) in a set of infeed
belts.

B. Accelerate bottles in a set of high speed belts to provide sufficient separation between
bottles for bottle orientation as determined by the "functional requirement."

C. Process and properly orient the bottles as determined by their "functional requirement".

D. Slow the properly oriented bottles in a set of exit belts for stable transfer onto the customer
conveyor (symmetrical bottles).

The "functional requirement" differs from machine to machine and from bottle to bottle within the
same machine. Examples of "functional requirements" follow:

* Position bottles from a horizontal, neck or base leading orientation, into a standing
position.

* Position bottles from a horizontal, neck or base leading orientation, into an upside down
orientation in which they pass over an air rinse station and then are processed into a
"normal stand up."

The "functional requirement" determines the specific design of the tooling that is developed by
Pace. The versatility of the stand up unit permits Pace to accommodate an almost unlimited range
of requirements in such a way that very minor adjustments will be required during production
changeovers.

The tooling developed at Pace for a given unscrambler is detailed in Section VII - Set Up
Instructions.

Warning

Care must be taken over the following:

1. Electrical Connections and Panels should not be opened with or interfered with except by a
suitably qualified technician.
2. Machine must be operated with guards in place.
3. Guard Interlocks function should be checked weekly by a qualified technician.

Page 7 / 170

BOTTLE AXIAL ORIENTOR 5000E
Warning
All operators must be properly trained in the use of this equipment
The Pace Bottle Axial Orientor (BAO) orients non-symmetrical bottles about their vertical axis
so that they are all in one direction, for example, all handles trailing.
The BAO receives bottles in mixed orientation on its conveyor. They come under control of
"hesitator belts" which provide spacing between the bottles to prevent interference during
orientation.
A. If a bottle is correctly oriented, a pair of moving belts apply a torque to its neck. The
bottle tries to turn, but a rail contacting the body of the bottle prevents any turn.
B. If a bottle is incorrectly oriented, a pair of moving belts apply a torque to its neck. The
bottle does a "guided turn" through 180 degrees into the correct orientation. It stops
turning when the rail contacts the body of the bottle and prevents any further turn.
During each "guided turn", the top conveyor stabilizes the bottle. Springs under the top
conveyor allow for a small variation in bottle height. The speed of the top conveyor and the
BAO main conveyor are the same.
The BAO is equipped with a downstream photo electric sensor to stop the hesitator belts when
a downstream back up occurs. This prevents bottles from entering the BAO when downstream
space to receive them is unavailable.
On Orientors integrated with a Pace unscrambler, the unscrambler disc stops running when a
back-up occurs and the orientor keeps operating.
Warning
Electrical Connections and Panels should not be opened or interfered with except by a
suitably qualified technician
The electrical system remains "live" regardless of the condition of the Start/Stop Control.
Power to the entire electrical system can only be shut down using the electrical disconnect
switch.
Changeover from one bottle size to another is accomplished by adjusting the hold down
conveyor, side rails, and sensor to the dimensions shown in the Set Up Instructions.
Page 8 / 170

SECTION IV PACE PACKAGING CORPORATION

INSTALLATION & START UP

GENERAL

Warning

Ensure that only qualified personnel perform any lifting and transport operations required to
place the equipment in the designated location.

It is important to do the following steps in the order presented to obtain the correct overall
height of the System.

ASSEMBLY

* Place pallet mounted machine sections in their desired locations on the production floor.

* Remove lag bolts from pallets. Lift the machine sections using the hot rolled steel bars
attached to the legs of the machine. Remove the pallets.

* If your System has a Bottle Axial Orientor (BAO), locate the BAO exit conveyor
closely against the customer conveyor for a smooth side transfer. DO NOT USE A
DEAD PLATE. If your System does not have a BAO, go to the next step.

* Place the unscrambler so that its exit belts are over the customer conveyor. The
unscrambler should be positioned so that the bottle contact surface of the operators side
exit belt is even with the edge of the customer conveyor chain.Vertically, adjust the feet
so that the bottom of the exit pulleys have the proper clearance to the exit conveyor as
specified in Section VII. The conveyor should be as far under the belts as possible
without hitting the exit tooling.

Locate the bulk hopper next to the disc.

Page 9 / 170


ELECTRICAL

Warning

Electrical Connections and Panels should not be opened or interfered with except by a suitably
qualified technician.

* Connect the System to factory power. Refer to electrical diagram for power input
requirement. Ensure that the factory ground is hooked to the PE (Physical Earth) terminals
located next to the power disconnect.

* System Start/Stop Control. All System motors start or stop under the command of this
control. This control affects only the power to the motors. The control circuits remain active.

Warning

The electrical system remains "live" regardless of the condition of the Start/Stop Control.
Power to the entire electrical system can only be shut down using the electrical disconnect
switch.

* Downstream Backup Control.
Standard. The downstream backup photo electric sensor with cable is packed at the
exit of the stand up unit. Install the sensor at a suitable location on the customer
conveyor. This control stops the output of the System if a bottle back up is sensed
on the conveyor. The System restarts automatically after a back up clears.

Disc Level Control. A photo electric sensor, located in the centrifugal disc, activates the
hopper motor as required to maintain the proper level of bottles in the disc.

COMPRESSED AIR

* If the System is provided with a hook mechanism or air cleaning system, it will require
compressed air. Connect compressed air supply at the fitting provided. The brass bulkhead fitting
will be located on the non-operator side of the machine.

Warning

The air supply should be disconnected when alterations or adjustments are made to the system.

Page 10 / 170


START UP
Warning

Ensure that all guards are fitted and working correctly before commencing start up.

* Many Pace Systems are started by customer personnel without assistance from a Pace Field
Service Representative. For assistance with start up and training, contact Pace to arrange for
a start up service visit.

* Inspect the entire System to be sure that all shipping straps and other shipping materials have
been removed, and that no physical damage has occurred.

* Set speed control dials on top of electrical enclosure to "300".

* With the machine empty of bottles, operate the START and STOP controls briefly and verify
that each of the modules of your System runs freely and in the proper direction.

* Set tooling and adjustments per Section VII - Set Up Instructions for the bottle size to be
handled and place a small quantity of those bottles into the hopper.

* Run the System and observe the bottle action throughout.

* Test the downstream back up control to verify that it will stop the System when blocked. If
your System has the automatic variable feed rate control, test for speed shift by blocking the
photo electric sensors and watching to see if the disc slows and then stops correctly.

* Adjust speeds to specifications provided for the bottle being run as shown in Section VII.

* After completing the above steps satisfactorily, the System is ready for production operation

* If the System was designed to unscramble more than one bottle, refer to Section VII - Set Up
Instructions for the required adjustments.

Page 11 / 170

SECTION V PACE PACKAGING CORPORATION

Trouble Shooting Guide

Symptom Check

No run on start-up.
1) Check power input at source.

2) Check all circuit breakers

3) Check to make sure all doors are fully closed
and that the E-STOP is not engaged.

Belts run
Disc & hopper do NOT run
Check the down-stream back-up sensor for
blockage or dirt.

Belts & Disc run
Hopper does NOT run.

Check the disc level sensor for blockage or dirt.

Hook does NOT return.
1) Check for proper pressure in supply line.

2) Check hook regulator setting against settings
called for in Section VII of the operator's manual for
current bottle.

Bottles do NOT stand up or
do NOT feed properly.
Check ALL settings against those called for in Section
VII of the operator's manual.
Belts jump off pulleys and rollers
creating jams and poor performance
Belts should be lubricated at least once every 2 shifts
or sooner if jumping is apparent.

Page 12 / 170
MAINTENANCE
Hopper belt replacement
(THE PACE HOPPER IS OPTIONAL.)
The following is a step by step instruction on how to
change a Pace Packaging hopper belt.

This process is universal for all 12, 16 and 24 belts.

Average time to complete with two people, 20-30
minutes.

It is important that this manual be read completely
before work begins.

There are safety considerations that must be planned
for before work starts.
RUBBERIZED 16 ELEVATOR
HOPPER BIN
SECTION VI PACE PACKAGING CORPORATION
Page 13 / 170
Elevator belt removal
Bef or e we begi n, unpl ug t he hopper f r om
t he unscr ambl er and l ock i t out .

The f i r st st ep i s t o gai n access t o t he
bel t .

Remove t he bel t adj ust ment scr ew cover s,
t he chut e, and t he el evat or bot t omguar ds.

Ret ai n al l har dwar e t hat has been r emoved.

CHUTE
ADJUSTMENT
SCREW COVER
BOTTOM GUARDS
Page 14 / 170
Wi t h t he chut e and bot t omguar ds r emoved,
you must now r emove t he f l ap assembl y
guar d f r omunder t he hopper bi n.

Measur e t he di st ance f r omt he hopper bi n
t o t he end of t he f l ap assembl y f l ange
and wr i t e i t down. Thi s measur ement wi l l
be usef ul when you r ei nst al l t hi s
assembl y. Remove t he f l ap assembl y and
set i t t o t he si de. Removi ng t he assembl y
wi l l make r ei nst al l i ng t he new bel t much
easi er .

Bef or e you l oosen t he bel t , t ake a
measur ement bet ween t he sl i de bl ock and
t he f i xed f l ange. Do t hi s on bot h si des
of t he hopper . They may be di f f er ent .

You can al so mar k wher e t he sl i de bl ock
i s but a measur ement i s mor e accur at e.
Thi s measur ement wi l l be usef ul when you
r e- t ensi on t he new bel t . Keep i n mi nd
t hat t he new bel t wi l l t r ack di f f er ent l y
t han t he ol d one. Thi s measur ement wi l l
hel p speed t he pr ocess.

Now l oosen t he adj ust ment bol t s on bot h
si des of t he hopper and al l ow t he sl i de
bl ock t o r et r act as f ar as possi bl e.
FLAP ASSEMBLY GUARD
SLIDE BLOCK (IDLER BEARING MOUNT)
ADJUSTMENT BOLT
Page 15 / 170
Now t hat t he t ensi on i s f ul l y
r emoved and t he bel t i s si t t i ng i n
t he el evat or l oose, r ot at e t he bel t
by hand unt i l t he bel t seaml i nes up
wi t h t he sl i de bl ock openi ngs. Gr ab
t he bel t on each si de of t he seam
and pul l t owar d you so t he seamhas
no pr essur e on i t . Have a hel per
gr ab t he pi n wi t h a pai r of pl i er s
and pul l i t out of t he seamsl owl y.

Once t he pi n has been r emoved, al l ow
t he bot t omsi de t o dr op. MAKE SURE
THE AREA UNDER THE BELT IS CLEAR.
Pul l t he t op si de t owar d you and
al l ow i t t o pi l e up on t he f l oor i n
f r ont of you. You may need some hel p
t o pul l t he bel t out i f i t get s
caught on ot her hopper component s.
Whi l e you ar e pul l i ng, have your
hel per t hr ead t he sl ack over any
obst r uct i ons.
GAP BETWEEN
DRUM & BELT
Page 16 / 170
Hopper Belt Installation
When you r ecei ve t he new bel t i t
shoul d be r ol l ed up wi t h t he cl eat s
f aci ng i n. Li f t t he new bel t r ol l ed up
so t hat t he l oose end i s poi nt i ng i nt o
t he hopper el evat or . Unr ol l t he bel t
and al l ow t he unr ol l ed end t o sl i de i n
and down t he hopper el evat or . Once you
have unr ol l ed enough t o r each t he
bot t omdr i ve dr um, ask your hel per t o
pul l t he bel t ar ound t he dr i ve dr um
and st ar t t hr eadi ng i t back up t o you.

You must hol d on t o t he end of t he
r ol l ed up bel t and cont r ol t he r at e of
speed whi l e your hel per i s pul l i ng t he
bel t . Thi s wi l l pr event t he bel t f r om
get t i ng caught on anyt hi ng and st op
t he end you ar e hol di ng f r omsl i di ng
down i nsi de t he hopper wher e you
cannot r each i t . I nsur e t hat t he bel t
i s t hr eaded over t he t op of t he back
r ol l er s and t hat t hese r ol l er s l i ne up
wi t h t he cut out s i n t he new bel t .

DIRECTION OF FEED
FOR NEW BELT
ROLLED UP NEW BELT
HOPPER BELT
CUT-OUTS
BACK ROLLERS
Page 17 / 170
Once t he new bel t i s t hr eaded
cor r ect l y, l i ne up t he t wo hal ves of
t he seam. Be ver y car ef ul t o l i ne up
t he seaml oops cor r ect l y f r omsi de
t o si de or t he bel t wi l l not t r ack
pr oper l y. When you ar e sur e t hat t he
seami s even, st ar t t o i nser t t he
pi n.

Thi s wi l l r equi r e t wo peopl e so your
hel per i s st i l l needed. As your
hel per pushes t he pi n i n you wi l l
have t o l i ne up t he seaml oops. Most
t i mes as you push t he pi n i n t he
seamwi l l l i ne up on i t s own.
However , i t i s easi er i f you l i ne up
t he seamas t he pi n i s bei ng
i nser t ed. Push t he pi n i n f ar enough
so t hat not hi ng st i cks out past t he
bel t . Ther e i s no need t o bend t he
ends over si nce t he t ensi on wi l l
hol d t he pi n i n pl ace.

The other side should line up the same as
this side. The belt should also be even.
PIN
Page 18 / 170
SAFETY WARNING
TO CORRECTLY TRACK THE NEW BELT IT MUST BE RUN FOR A PERIOD OF 15 MINUTES.
DURING THIS TIME THE BELT WILL SHIFT LEFT AND / OR RIGHT. INSTALLATION OF THE CHUTE
ASSEMBLY AND FLAPPER ASSEMBLY BEFORE THIS BELT TRACKING PERIOD WILL RESULT IN
DAMAGE TO THE BELT.
THE WORK AREA AROUND THE HOPPER MUST BE CLOSED OFF TO EVERYONE EXCEPT THE
MECHANIC(S) PERFORMINGTHE REPAIR.
A PERSON ACTING AS A SAFETY OFFICER MUST OPERATE THE EMERGENCY STOP SWITCH TO
INSURE THE SAFETY OF THE MECHANICS WHILETHE HOPPER IS RUNNING WITH OUT GAURDS.
FOLLOW ALL LOCAL SAFETY REGULATIONS REGARDING HAZARDOUS WORK ENVIORMENTS.
Stay clear of exposed belt while running!
Page 19 / 170
Now t hat t he new bel t i s i nst al l ed,
r et ur n t he sl i de bl ocks t o t he
measur ement you t ook bef or e.

Thi s i s onl y a st ar t i ng poi nt wi t h t he
new bel t . Each bel t t r acks di f f er ent l y.

Run t he hopper ver y sl owl y t o i nsur e i t
wi l l not wal k t o t he si de. Use t he
t ensi on adj ust ment bol t t o make f i ne
adj ust ment s t o wher e t he bel t i s
t r acki ng. Tr y t o cent er t he bel t i n t he
f r ame.

You may have t o r epeat t hi s pr ocess
af t er you r ei nst al l al l t he guar ds and
cl ean out cams.

Pl ease be ver y car ef ul . Damage can be
done ver y qui ckl y i f t he bel t i s not
t r acked cor r ect l y bef or e and af t er al l
guar ds ar e r ei nst al l ed!

SLIDE BLOCK (IDLER BEARING MOUNT)
ADJUSTMENT BOLT
Page 20 / 170
Whi l e you ar e i n t he pr ocess of
t r acki ng t he bel t you must moni t or t wo
cr i t i cal ar eas. :

1) THE BELT BACK ROLLERS:

These i dl er s wi l l over t i me cause
t ear s i n t he cl eat s i f t he bel t i s not
t r acked cor r ect l y. Af t er t he bel t i s
t r acked and t he back r ol l er s ar e not
i n t he cent er of t he cl eat cut out ,
you can r eposi t i on t hemt o bet t er
al i gn wi t h t he bel t cut out s.

2) HOPPER CHUTE BELT CLEAN-OUTS:

These cl ean out s mount t o t he hopper
chut e and wi l l not be a pr obl emunt i l
you r ei nst al l t he chut e/ guar d. Af t er
you have r ei nst al l ed al l guar ds and
t he chut e, you must r epeat t he i ni t i al
t r acki ng pr ocedur e and wat ch t o ensur e
t hat t he bel t does not cont act t hese
cl ean out s. I f t he bel t does cont act
t he cl ean- out s, you can l oosen t he
mount i ng scr ews t hat hol d t hese pi eces
i n and shi f t t hemsl i ght l y.
BACK ROLLERS
HOPPER BELT
CUT-OUTS
HOPPER BELT
CLEAN-OUTS
Page 21 / 170
The bot t omf l apper guar d i s t he l ast ar ea of
concer n. The f l apper assembl y has pl ast i c
cl ean- out s mount ed t o i t t hat must al so al i gn
wi t h t he bel t cut - out s.

These can be moved sl i ght l y i f needed. I f t hey
cannot be moved enough by l ooseni ng t he
mount i ng scr ews, check t o see i f t he hopper
bel t i s posi t i oned cor r ect l y i n t he hopper
f r ame.

Once you have t hese f ew cr i t i cal ar eas al i gned,
r ei nst al l t he r emai ni ng guar ds and put t he
hopper back i n ser vi ce.

You may want t o check on t he bel t al i gnment
over t he next day or t wo t o i nsur e t hat t he
bel t has not wal ked out of al i gnment .
FLAPPER ASSEMBLY
CLEAN-OUTS
FLAPPER ASSEMBLY
CLEAN-OUTS
HOPPER BELT
CUT-OUT
CLEAT CLEAT
Bottom flapper assembly/guard
Page 22 / 170

NOTE: NEVER REMOVE MORE THAN 1 TOP BAR MOUNTING BOLT AT A
TIME.

In order to easily change the infeed and high speed (twin-A) belting on the Pace machine,
follow these steps:

(1) Disconnect power from Pace machine.
(2) Open 41 cabinet door to reveal operators side of stand up unit.
(3) The top bar support rod must be intact and tightened before removing top bar
mounting bolts.
(4) Remove the M10X 1.5 bolt and spacer between the boom support bar and the top
tooling bar.
(5) Slide out the old belt through the gap that is formed between boom support bar and the top
tooling bar.
(6) Slide in new belt(s) and install it on the pulleys.
(7) Reinstall the spacer and bolt between the boom support bar and the top tooling bar.

right hand
machine
BELT INSTALLATION INSTRUCTIONS
(INFEED AND HIGH SPEED BELTS)
boom support bar 1
top tooling bar
Top bar support bolt
MDU

Top bar support

MDU
Top bar support
Top bar support
Left hand
machine
disc
disc
MDU
boom support bar 2
Page 23 / 170


boom support bar 3
BELT INSTALLATION INSTRUCTIONS
(EXIT BELTS)
Spacer
NOTE: NEVER REMOVE MORE THAN 1 TOP BAR
MOUNTING BOLT AT A TIME.
boom support bar 4
Bolt
In order to easily change the exit (twin-A) belting on the Pace machine, follow these steps:

(1) Disconnect power from Pace machine.
(2) Open 41 cabinet door to reveal operators side of stand up unit.
(3) The top bar support rod (see previous page for location) must be intact and tightened
before removing top bar mounting bolts.
(4) Remove the M10X 1.5 bolt and rectangular spacer located on the boom support bar.
(5) Slide out the old belt through the gap that is formed between the boom support bar and the
tooling bar.
(6) Slide in the new belt(s) and install it on the pulleys.
(7) Reinstall the rectangular spacer and bolt back onto the boom support bar.
Spacer
Page 24 / 170
NEVER LUBRICATE
POWER RAMP BELTS!

MAINTENANCE
BELTS

Warning
Before performing any maintenance functions on machinery, remove all power and use proper lockout, tagout procedures.

Note:
Your machine may have more or less belts than the diagram shown below depending upon your application.

BELT LUBRICATION

The lubrication of the bottle control belting (see figure above) is essential for proper performance. Belts that are not lubricated will
walk or jump off of the drive pulleys and guide rollers. This will cause poor performance, jams, and premature wear to the belting. A
thin filmof F.D.A. approved food grade grease is applied to the back of Twin-A or grooved belts only. This filmreduces friction
related heat build up and prevents the belt fromwalking off the drive pulleys during normal operations.

The recommended way to apply this grease is simple. Apply a small amount to your index finger. Only enough to cover the tip of the
finger about thick is necessary. Spread the grease using your finger to one section of the grooved side of the belt spreading it out so
it no longer is visible. One application only is necessary for shorter belts. Two applications may be needed on the longest high speed
belts. Lubricate belts as often as needed. The customer need is determined by production requirements. Check for lubrication on the
pulley side of the bottle processing belts every shift start. Once this is complete allow the machine one or two minutes run without
bottles before production resumes.
The end result will be a very thin filmon the V-groove section of the belt. Belts should be lubricated at least once every 2 shifts or
sooner if jumping is apparent. Never over grease and never lubricate the bottle contact side of the belts.

Never lubricate the set of Single-A drive belts or the Rotary Bumper Drive Belts! Never lubricate Power Ramp belts (optional).
Lubricate only the bottle control belting.

LUBRIPLATE SUPER FML-2 PACE PART # 32610 IS RECOMMENDED FOR BELT LUBRICATION
NEVER LUBRICATE THESE SINGLE A DRIVE BELTS!
Bottle control belting
Stand up unit drive
Disc drive
M500 HK
NEVER LUBRICATE THE ROTARY
BUMPER DRIVE BELT(S)!

MOTOR DRIVEN ROTARY BUMPER
ROTARY BUMPER
NEVER LUBRICATE THE ROTARY
BUMPER DRIVE BELT(S)!
NON-MOTOR DRIVEN ROTARY BUMPER
ROTARY BUMPER

1 2 3
Bottle control belting
BAO 5000E
NEVER LUBRICATE
TURNING BELTS!
NEVER LUBRICATE THE
DISC DRIVE BELTS!
Page 25 / 170


MAINTENANCE (continued)

BELT CLEANING

Along with proper belt tension, correct belt maintenance is important to obtain the longest life
and best performance from these belts.

URETHANE TWIN A BELTS ONLY

Over time the bottle control belting will become dirty and need to be cleaned. To do this
without damaging the texture of the belt, use a mild detergent with water for best results. A
sponge or fine scotch-bright pad will also increase the cleaning effectiveness. Be sure belts
are completely dry before operating in production. (Never use any type of alcohol or other
petroleum product to clean the urethane belts.)

URETHANE TWIN A BELTS & SOFT CLOTH COVERED BELTS

Warning
Check to ensure that the soft cloth covering of the belting will not rub against any
component of the machine. Top Tooling must be tightened before machine start-up.

REDUCER LUBRICATION

Lubrication requirements are minimal.

SEALED REDUCERS (MOTOVARIO & 90 DEGREE CROWN DRIVES):

* These reducers are non vented, filled with synthetic lubricants & require no
lubrication.

ELECTRICAL

* For customers with DC Motors only:
Inspect DC Motor Brushes for wear every 4 months or 1000 hours of operation.

DISC CLEANING

Warning

Proper Housekeeping is paramount to maintain a safe & efficient machine. All areas of
the machine must be kept free of foreign matter. The area between the rotating stainless
steel disc and the fixed non-rotating disc that it is mounted upon can be a point where
unseen debris may colllect. Access to clean this area with a vacuum hose can be found on
the operator side of the machine. Cleaning of this area shall be performed at least once a
month in order to prevent a build up of debris and potentially unsafe conditions.

Page 26 / 170

SET-UP SPECIFICATION DIAGRAMS
SECTION VII

Page 27 / 170

BOTTLES FOR SERIAL NUMBERS 3909&3910
NO. SIZE TYPE Color MATERIAL
1 850 ml Suavizante Oval White HDPE

Page 28 / 170
DISC RING CHANGE-OVER
(SEE NEXT PAGE FOR PARTS IDENTIFICATION)
FIGURE 1A

(1) DISC DOOR REMOVAL

LOOSEN THE LEVER IN ORDER TO RELEASE THE DISC DOOR ASSEMBLY. PULL THE DISC DOOR
ASSEMBLY OFF THE SCALE BAR.

(2) INSTALL OR REMOVE DISC RING AS DIRECTED BY THE TABLE IN FIGURE 1B.

(3) DISC DOOR INSTALLATION

PUSH THE DISC DOOR ASSEMBLY ALL THE WAY IN ON THE SCALE BAR UNTIL IT IS IN CONTACT WITH
THE TOP BAR. TIGHTEN THE LEVER TO SECURE THE DISC DOOR IN PLACE.
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
A
B
Page 29 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TOP TOOLING
DISC DOOR ASSEMBLY
LEVERS
SCALE BARS
BOTTLE FLOW
DISC RING CHANGE-OVER
FIGURE 1A-CONTINUED
INFEED VIEW OF MACHINE
Page 30 / 170

DISC TOOLING USED
FIGURE 1B
BOTTLE SIZE MAIN DISC RING 1 RING 2
850 ML INSTALL INSTALL

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
NOTE: RINGS THAT ARE REMOVED MUST BE STORED ON A FLAT SURFACE. IF THE RINGS ARE HUNG
FROM A HOOK, THEY WILL BECOME DISTORTED AND UNABLE TO BE SERVICED.
DISC WALL
POLY DISC
FLOOR PLATE
POLY RING
URETHANE
BELT
Page 31 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
VIEW SHOWN
B
ROTARY
BUMPER
ASSEMBLY
ROTARY BUMPER SETTINGS
FIGURE 2
BOTTLE SIZE A B
850 ML 01040 14.4
1000 ML 00850 14.4
1900 ML 00700 14.4

A
Page 32 / 170

INPUT SHEAVE HEIGHT
FIGURE 3
BOTTLE SIZE A
850 ML 2.7 CM
1000 ML 2.7 CM
1900 ML 2.7 CM

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(A)
NON-
OPERATORS
SIDE BELT
NOTE: FOR REFERENCE PURPOSES
ONLY. DO NOT ADJUST!
TOOLING DISC
FRONT VIEW: CUTAWAY ILLUSTRATION
VIEW SHOWN
TOP BAR
INFEED IDLER
Page 33 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
HOOK
HOOK SETTINGS
FIGURE 4A
BOTTLE SIZE HOOK A B C D E
850 ML
1000 ML
1900 ML

CLOSE-UP OF CUTAWAY
(A)
(D)
OPERATORS
SIDE
(C)
Bottle flow
(B)
(E)
Page 34 / 170
AIR PRESSURE SETTINGS
FIGURE 4B
BOTTLE SIZE
A
HOOK
B
DISC
850 ML N/A 3 BAR
1000 ML N/A 3 BAR
1900 ML N/A 3 BAR

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
AIR REGULATOR
(A)
VIEW SHOWN
(B)
(A)
Page 35 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
ADJ UST REGULATOR TO 0
PSI TO CHANGE HOOK.
READJ UST PRESSURE
SETTINGS FOR REQUIRED
BOTTLE (SEE FIGURE 4B).
THIS SETSCREW MUST BE
TIGHT AGAINST THE FLAT
OF THE ACTUATOR SHAFT.
HOOK LOCKING SCREW.
LOOSEN TO ADJ UST OR
CHANGE HOOK.
HOOK
HOOK ADJ USTMENT
FIGURE 4C
BOTTLE FLOW
Page 36 / 170

(A)
RED LEVER CLAMP
BOTTLE
FLOW
NOTE: LOOSEN RED TIE BRACKETS (INPUT END,
TOP TOOLING BAR) BEFORE ADJUSTING BELT SEPARATION.
(B)
BOTTLE FLOW
(A)
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
BELT SEPARATION
FIGURE 5
BOTTLE SIZE A B C
850 ML 00330 11.8 16.4 CM
1000 ML 00315 12.0 16.2 CM
1900 ML 00525 9.4 18.9 CM

(C)
Page 37 / 170

DIMENSION MOVEMENT DIRECTION
DIMENSION A LEFT TO RIGHT
DIMENSION B UP OR DOWN
DIMENSION C IN OR OUT
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
VIEW OF THE INFEED SECTION OF MACHINE
BOTTLE FLOW
TOOLING
ROLLER
(A)
(C)
(B)
BOTTLE FLOW
TOOLING
(C)
BOTTLE FLOW
ROLLER
(A)
(B)
Page 38 / 170

TOP BAR SETTINGS
FIGURE 6A
BOTTLE SIZE: MAIN SET-UP
OPERATORS SIDE NON-OPERATORS SIDE
CLP TYP A B C CLP TYP A B C
1 LIF 10.2 2.7 4.3 1 TL 3.0 5.7 3.3
2 UIF 18.0 2.5 4.5 2 DD 15.1 X 3.1
3 3 TL 24.8 5.7 2.8
4 LIF 36.0 2.7 4.5 4 DD 40.0 X 2.0
5 UIF 44.0 2.5 4.5 5 TL 42.6 4.5 3.4
6 6 IF 48.0 2.7 4.7
7 LIF 60.8 2.7 4.5 7 TL 54.6 4.5 3.4
8 HS 90.0 2.5 4.5 8 HS 81.0 2.5 4.5
9 9 HS 106.0 2.5 4.5
10 HS 112.0 2.5 4.5 10 HS 137.4 2.5 4.7
11 11 EX 144.5 2.2 5.1
12 HS 141.4 2.5 4.3 12 HS 147.8 2.5 4.7
13 HS 163.4 2.5 4.1 13 EX 157.8 2.2 4.7
14 EX 169.4 2.2 4.7 14 EX 162.0 2.2 4.7
15 HS 174.0 2.5 4.0 15 EX 174.2 2.2 4.2
16 HS 183.0 2.5 4.0 16 EX 192.0 2.2 4.2
17 17
18 EX 202.6 2.2 4.0 18
19 19
20 20
21 21
22 22

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
CLAMP TYPE: IF=INFEED BELT
CLAMP TYPE: TL=TOOLING
CLAMP TYPE: DD=DISC DOOR
CLAMP TYPE: EX=EXIT BELT
CLAMP TYPE:HS=HIGH SPEED BELT
CLAMP TYPE:SSD=SLOW SPEED BELT
(A)
(C)
(B)
BOTTLE FLOW
TOOLING
(C)
BOTTLE FLOW
ROLLER
(A)
(B)
Page 39 / 170

TOP BAR SETTINGS
FIGURE 6B
BOTTLE SIZE: 850 ML
1 1
2 2
3 TTL-1 22.4 7.0 5.0 3
4 4
5 5
6 BTL 52.4 3.0 5.5 6
7 7
8 8
9 TTL-1 98.8 4.8 5.0 9
10 10
11 TTL-2 138.7 6.7 4.5 11
12 12
13 13
14 14
15 15
16 16
17 EX 186.0 2.2 3.7 17
18 18
19 19
20 20
21 21
22 22

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(A)
(C)
(B)
BOTTLE FLOW
TOOLING
(C)
BOTTLE FLOW
ROLLER
(A)
(B)
Page 40 / 170

TOP BAR SETTINGS
FIGURE 6C
BOTTLE SIZE: 1000 ML
1 1
2 2
3 TTL-1 22.4 8.5 5.0 3
4 4
5 5
6 BTL 52.4 3.3 5.5 6
7 7
8 8
9 TTL-1 98.8 6.0 5.0 9
10 10
11 TTL-2 136.5 7.8 4.5 11
12 12
13 13
14 14
15 15
16 16
17 EX 190.4 2.2 3.3 17
18 18
19 19
20 20
21 21
22 22

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(A)
(C)
(B)
BOTTLE FLOW
TOOLING
(C)
BOTTLE FLOW
ROLLER
(A)
(B)
Page 41 / 170

TOP BAR SETTINGS
FIGURE 6D
1 1
2 2
3 TTL-1 22.4 11.3 3.3 3
4 4
5 5
6 BTL 52.4 3.3 5.5 6
7 7
8 8
9 TTL-1 98.8 9.5 3.3 9
10 10
11 TTL-2 136.5 10.0 3.3 11
12 12
13 13
14 14
15 15
16 16
17 EX 190.4 2.2 3.7 17
18 18
19 19
20 20
21 21
22 22

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(A)
(C)
(B)
BOTTLE FLOW
TOOLING
(C)
BOTTLE FLOW
ROLLER
(A)
(B)
Page 42 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
POWER RAMP BELT
FRONT OF THE MACHINE
BOTTLE FLOW
CUT AWAY VIEW OF POWER RAMP AREA
POWER RAMP IDENTIFICATION PAGES
FIGURE 7A
Page 43 / 170
BOTTLE FLOW
INFEED BOTTOM TOOLING
EXIT BOTTOM TOOLING
MOTOR
POWER RAMP BELT
CENTER TOOLING BAR
POWER RAMP IDENTIFICATION PAGES
FIGURE 7B
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 44 / 170
FIGURE 7C
BOTTLE SIZE A B C
850 ML 0.5 3.4 1.6
1000 ML 0.5 2.1 1.6
1900 ML 0.5 1.0 1.6

CENTER TOOLING BAR
(C)
BOTTLE FLOW
(B)
(A)
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 45 / 170
EXIT BOTTOM TOOLING
FIGURE 8
BOTTLE SIZE A B C
850 ML 7.7 8.5 1.2
1000 ML 7.7 8.5 1.2
1900 ML 7.7 8.5 1.2

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(C)
(B)
BOTTLE FLOW
EXIT BOTTOM TOOLING
(A)
CENTER TOOLING BAR
Page 46 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
EXIT BOTTOM
TOOLING
EXIT BELT CLEARANCE
FIGURE 9A
A 1.8 CM

*(A)
TOP BAR
CUSTOMERS
TAKE AWAY
CONVEYOR
EXIT BELT
CLOSE-UP OF THE END OF THE MACHINE
FRONT VIEW: CUTAWAY ILLUSTRATION
Page 47 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
A
B
BOTTLE FLOW
BOTTLE STABILIZER TOOLING
SETTINGS
FIGURE 9B
BOTTLE SIZE A B
850 ML 166.2 6.5
1000 ML 166.2 6.5
1900 ML 166.2 6.5

Page 48 / 170

SPEED SETTINGS (HERTZ SETTINGS)
FIGURE 10A
INFEED BAO
BOTTLE
SIZE@BPM
HIGH
SPEED
LOW
SPEED
BACK-UP
SPEED
HIGH
SPEED
LOW
SPEED
BACK-UP
SPEED
DISC
AIR
ENABLE
BAO
CAMERA
SELECT
CAMERA
PROGRAM
ORIENTATION
DIRECTION
850 ML 24.0 15.0 15.0 26.0 20.0 20.0 1 1 1 1 1
1000 ML 26.0 15.0 15.0 35.0 20.0 20.0 1 1 1 2 1
1900 ML 19.0 12.0 12.0 24.0 15.0 15.0 1 1 1 2 1

SPEED SETTINGS (HERTZ SETTINGS)
FIGURE 10A
HOPPER DISC BUMPER SUU POWER RAMP
BOTTLE
SIZE@BPM
HIGH
SPEED
LOW
SPEED
BACK-
UP
SPEED
HIGH
SPEED
LOW
SPEED
BACK-
UP
SPEED
HIGH
SPEED
LOW
SPEED
BACK-
UP
SPEED
HIGH
SPEED
LOW
SPEED
BACK-
UP
SPEED
HIGH
SPEED
LOW
SPEED
BACK-
UP
SPEED
850 ML 30.0 15.0 X 30.0 20.0 X 50.0 30.0 30.0 37.0 20.0 20.0 38.0 20.0 20.0
1000 ML 30.0 20.0 X 32.0 25.0 X 60.0 30.0 30.0 38.0 20.0 20.0 40.0 30.0 30.0
1900 ML 30.0 15.0 X 25.0 12.0 X 50.0 25.0 25.0 25.0 15.0 15.0 22.0 22.0 22.0

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 49 / 170

* SPEED SETTINGS (FEET PER MINUTE) FPM
FIGURE 10D (REFERENCE ONLY!)

BOTTLE
SIZE
INFEED
SUU
(FPM)
HIGH
SPEED
SUU
(FPM)
EXIT
SUU
(FPM)
POWER
RAMP
(FPM)
INFEED
TRANSFER
(FPM)
BAO
(FPM)
850 ML 230 325 742 110 137
1000 ML 230 325 880 123 180
1900 ML 125 169 430 90 129

*WARNING:

THE SPECIFICATIONS ON THIS PAGE ARE
MEANT FOR REFERENCE ONLY TO ASSIST
IN CUSTOMER CONVEYOR INTEGRATION.

THE CUSTOMER IS ADVISED BY PACE TO
INFORM HIS PERSONNEL THAT THEY ARE
NOT TO REACH INTO THE MACHINE AND
OBTAIN SPEED READINGS WHILE THE
MACHINE IS IN OPERATION.
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13

DISC
FEEDER
BOTTLE FLOW
STAND-UP UNIT
EXIT BELTS
Page 50 / 170
DRIVES ACCEL/ DECEL TIMERS
FIGURE 10E (ALL BOTTLES)
NOTE: SOME OF THE DEVICES LISTED ON THIS PAGE MAY NOT APPLY TO THE CUSTOMERS PARTICULAR APPLICATION.
DRIVES ACCEL TIMERS TIME IN TENTHS OF A SECOND (.1S):
HOPPER ACCEL TIME:
20
DISC ACCEL TIME:
90
BUMPER ACCEL TIME:
20
SUU ACCEL TIME:
50
POWER RAMP ACCEL TIME:
30
INFEED ACCEL TIME:
30
BAO ACCEL TIME:
20

DRIVES DECEL TIMERS TIME IN TENTHS OF A SECOND (.1S):
HOPPER DECEL TIME:
20
DISC DECEL TIME:
90
BUMPER DECEL TIME:
30
SUU DECEL TIME:
20
POWER RAMP DECEL TIME:
30
INFEED DECEL TIME:
20
BAO DECEL TIME:
20

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 51 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TIMERS PAGE 1
FIGURE 10F
BOTTLE SIZE BPM
OUTFEED
ACCUMULATION
PE BLOCKED
TIMER:
OUTFEED
ACCUMULATION
PE UNBLOCKED
TIMER:
NORMAL
STOP
DELAY
TIMER:
DISC BOTTLE
DEMAND PE
UNBLOCKED
TIMER
DISC BOTTLE
DEMAND PE
BLOCKED
TIMER
BRIDGE
BREAKER ON
TIMER:
BRIDGE
BREAKER OFF
TIMER:
850 ML 290 2.00 2.00 1.00 0.20 3.50 4.00 10.00
1000 ML 275 2.00 2.00 1.00 0.20 3.50 4.00 10.00
1900 ML 120 2.00 2.00 1.00 0.20 3.50 4.00 10.00

Page 52 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TIMERS PAGE 2
FIGURE 10G
BOTTLE
SIZE
BPM
SPEED
SHIFT PE
BLOCKED
TIMER:
SPEED SHIFT
PE
UNBLOCKED
TIMER:
OUTFEED
ZERO PE
SPEED
BLOCKED
TIMER
OUTFEED
ZERO PE
SPEED
UNBLOCKED
TIMER
BAO JAM
ALARM
PE
BLOCKED
TIMER:
BAO JAM
ALARM PE
UNBLOCKED
TIMER:
EXIT JAM
ALARM
TIMER:
EXIT JAM NO
MOTION
ALARM
TIMER:
850 ML 290 1.0 1.0 600.0 1.0 2.00 10.00 0.30 0.25
1000 ML 275 1.0 1.0 600.0 1.0 2.00 10.00 0.30 0.25
1900 ML 120 1.0 1.0 600.0 1.0 2.00 10.00 0.30 0.25

Page 53 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TIMERS PAGE 3
FIGURE 10H
BOTTLE SIZE BPM
DOWNSTREAM
MOTION
CONTROL (CTS)
LOW SPEED
ENABLE
CONTROL
LOW SPEED
OVERRIDE
CONTROL
(CTS)
LOW SPEED OVERRIDE TIMER
850 ML 290 5
1000 ML 275 5
1900 ML 120 5

Page 54 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
LATERAL PRESSURE
ASSEMBLY
INFEED HESITATOR
ASSEMBLY
TURNING BELT
RAILS
TOP CONVEYOR HEIGHT
ADJUSTMENT
TOP CONVEYOR
BOTTLE FLOW
BOTTLE FLOW
Page 55 / 170

TRANSFER ROLLER SETTINGS
FIGURE 11A
BOTTLE SIZE: 850 ML
POST A B C
1 4.0 1.0 0.0
2 2.4 1.8 0.0
3 2.2 2.1 0.0

(C)
(A)
(B)
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13

STAND UP UNIT/BAO TRANSFER ROLLERS
1
2
3
BOTTLE
FLOW
BOTTLE
FLOW
TRANSFER BELTS
Page 56 / 170

FIGURE 11B
POST A B C
1 4.5 1.0 0.0
2 2.2 1.8 0.0
3 2.6 2.1 0.0

(C)
(A)
(B)
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13

1
2
3
BOTTLE
FLOW
BOTTLE
FLOW
TRANSFER BELTS
Page 57 / 170
FIGURE 11C
POST A B C
1 4.8 1.0 0.0
2 3.8 1.8 0.0
3 3.8 2.1 0.0

(C)
(A)
(B)
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13

1
2
3
BOTTLE
FLOW
BOTTLE
FLOW
TRANSFER BELTS
Page 58 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
INFEED HESITATOR SETTINGS
FIGURE 12
* C & D ARE MEASURED FROM THE TOP OF THE
BOTTOM CONVEYOR (METAL FRAME) TO THE
BOTTOM OF THE PULLEY.
BOTTLE SIZE A B C D
850 ML 7.7 6.6 2.9 2.1
1000 ML 8.0 6.6 2.9 2.1
1900 ML 6.5 7.0 2.9 2.1

*(D)
*(C)
BOTTLE FLOW
VIEWED FROM THE OPERATORS SIDE
(A)
(B)
BOTTLE FLOW
OPERATORS SIDE
NON-OPERATORS SIDE
BOTTLE FLOW
INFEED HESIATATOR ASSEMBLY
Page 59 / 170

LATERAL PRESSURE UNIT STROKE SETTINGS
FIGURE 13
BOTTLE SIZE A B C D TURNING PAD
850 ML 14.3 0.7 4.2 1.6
1000 ML 14.1 0.7 4.4 1.6
1900 ML 15.4 0.7 3.0 1.6

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(A)
LATERAL
PRESSURE
ASSEMBLY
FRONT VIEW
(D)
(B)
(C)
Page 60 / 170

LATERAL PRESSURE UNIT AIR SETTING
FIGURE 14
BOTTLE SIZE A
850 ML 85 PSI
1000 ML 85 PSI
1900 ML 85 PSI

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(A)
PRESSURE
GAUGE
BOTTLE FLOW
Page 61 / 170

TURNING BELT
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TURNING BELT SETTINGS
FIGURE 15
BOTTLE SIZE A B
850 ML 10.7 9.5
1000 ML 10.7 9.5
1900 ML 10.7 9.5

BOTTLE FLOW
TURNING BELT
BOTTLE FLOW
MOTOR
TURNING BELT
(OPERATOR SIDE)
TURNING BELT
(NON-OPERATOR SIDE)
(B)
(A)
Page 62 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(B)
BOTTLE FLOW
TRIGGER EYE SETTINGS
FIGURE 16A
BOTTLE SIZE A B
850 ML 3.4 1.3 CM
1000 ML 3.4 1.3 CM
1900 ML 3.4 1.3 CM

(A)
Page 63 / 170

(A)
BOTTLE
FLOW
CAMERA EYE SETTINGS
FIGURE 16B
BOTTLESIZE A B C CAMERA
SELECT
PROGRAM ORIENT-
ATION
LENS
PART#
SIZE
OF
LENS
(mm)
DISC
AIR
850 ML
2.5 15.8 9.6 1 1 1 38452 8 MM 1
1000 ML
5.5 9.5 9.6 1 2 1 38452 8 MM 1
1900 ML
3.0 8.2 10.0 1 2 1 38452 8 MM 1

VIEW # 2
VIEW # 2
( B)
( C)
VIEW # 1: OPERATORS SIDE
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 64 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
COUNTER EYE SETTINGS
FIGURE 16C
BOTTLE SIZE A B
ALL BOTTLES 3.9 2.7 CM

( A)
( B)

( B)
BOTTLE FLOW
Page 65 / 170

RAIL CHANGE-OVER PROCEDURE

1) REMOVE THE OPERATORS AND NON OPERATORS SIDE RAIL BY LOOSENING
THE RAIL LEVERS ON THE MACHINE.

2) IDENTIFY WHICH ONE OF THE RAIL CONFIGURATIONS IS SUITED FOR THE
BOTTLE SIZE THAT YOU INTEND TO RUN. EACH RAIL IS STAMPED
APPROPRIATELY. INSTALL THIS RAIL.

3) LOCK THE RAIL IN PLACE USING THE LEVERS REMOVED EARLIER.

4) IDENTIFY THE BOTTLE SIZES STAMPED ON THE NON-OPERATORS SIDE RAIL.
RAIL
LEVER
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 66 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
BOTTLE FLOW
850 ML OPERATORS SIDE
850 ML NON-OPERATORS SIDE
Page 67 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
1000 ML OPERATOR'S SIDE
BOTTLE FLOW
Page 68 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
1900 ML OPERATOR'S SIDE
BOTTLE FLOW
Page 69 / 170
RAIL SUPPORT HEIGHT
FIGURE 18A
BOTTLE SIZE: ALL BOTTLES
RAIL POST A
1
3.5
2 3.5
3 3.5
4 3.5
5 3.5
6 3.5

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
A
BOTTLE FLOW
1
2 3
4
6
5
Page 70 / 170

(B)
VIEWED FROM LOOKING STRAIGHT AT THE RAIL
(A)
VIEWED FROM UNDERNEATH
THE RAIL
RAIL
POST
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
NECK RAIL ADJUSTMENTS
FIGURE 18B: ALL BOTTLES
POST (1 THRU 2) A B
1 1.9 1.5
2 1.8 1.5

BOTTLE
FLOW
1
2
Page 71 / 170

TOP CONVEYOR HEIGHT
FIGURE 19A
BOTTLE SIZE A
850 ML 01135
1000 ML 00995
1900 ML 00865

(A)
EXIT END OF BAO 5000E
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 72 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TOP CONVEYOR (REFERENCE)
FIGURE 19B
BOTTLE SIZE A B C D
850 ML 5.9 23.5 23.5 5.9
1000 ML 5.9 23.5 23.5 5.9
1900 ML 5.9 23.5 23.5 5.9

BOTTLE FLOW
(B)
(A)
(D)
(C)
BOTTLE FLOW
VIEW SHOWN
Page 73 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TOP CONVEYOR
(A)
(B)
BOTTLE FLOW
TOP CONVEYOR PITCH
FIGURE 19C
BOTTLE SIZE A B
850 ML 10.7 11.3
1000 ML 10.7 11.3
1900 ML 10.7 11.3

Page 74 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
DISC WALL PHOTO EYE HOLE
FIGURE 20
BOTTLE SIZE A
850 ML 14"
1000 ML 14"
1900 ML 14"

DISC WALL
DISC WALL PHOTO EYE
A
Page 75 / 170

IDLER PULLEY MEASUREMENTS
FIGURE 21
PULLEY NUMBER A
1 2.8
2 2.8
3 2.4
4 1.6
5 2.8
6 2.6
7 1.3

*MEASUREMENTS ARE MADE FROM
THE EDGE OF THE SHEAVE TO THE
EDGE OF THE PERCH.
DISC
BOTTLE FLOW
OPERATORS SIDE TOP BAR
NON-OPERATORS SIDE TOP BAR
3
5 6
7
BOTTLE FLOW
1 4
TOP BAR IDLERS
2
*A
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 76 / 170
BELT DOCUMENTATION
FIGURE 22
BELT NAME BELT TYPE PART NO.
(A) ROTARY BUMPER BELT SINGLE A 34806
(B) ROTARY BUMPER BLADES WHITE 32934
(C) UPPER INFEED BELT
(OPERATORS SIDE) OPTIONAL
TWIN A 37524
(D) LOWER INFEED BELT
(OPERATORS SIDE)
TWIN A 35438
(E) INFEED BELT (NON-
OPERATORS SIDE)
TWIN A 35478
(F) HIGH SPEED BELT TWIN A 34524
(G) EXIT TWIN A 35400
(H) SUU/BAO TRANSFER TWIN A 34702
(I) GEAR BELT D850H100 30391
(J ) DRIVE BELT SINGLE AX2 35536
(K) HOPPER ELEVATOR BELT 2" CLEAT 46984
(L) HOPPER HORIZ. BELT NO CLEAT 47223
(M) DISC DRIVE BELT B-40 36277
(N) POWER RAMP BELT TWIN A 32180

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(K)
HOPPER IS
OPTIONAL
(C)
OPTIONAL
(F)
(G)
(H)
OPTIONAL
BOTTLE FLOW
(D)& (E)
MDU
(I)
(J )
DISC WALL
(M) DISC DRIVE BELT(S)
POLY DISC
(M) POWER RAMP
(A)
(B)
Page 77 / 170
DRIVE BELT RUN (FIGURE 24)
VIEWED FROM UNDERNEATH THE MACHINE
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
DRIVE PULLEY LAYOUT PAGE
FIGURE 23
PULLEY NAME DESC. PART NO.
PULLEY(1) 24HH100 30778
PULLEY(2) IDLER 34656
PULLEY(3) 28HH100 30781
PULLEY(4) 2AK46 36810
PULLEY(5) 28HH100 30781
PULLEY(6) 2AK46 36810
PULLEY(7) IDLER 34656
PULLEY(8) 2AK25 36806
PULLEY(9) 2AK25 36806
GEAR BELT D850H100 30391
DRIVE BELT SINGLE AX2 35536

PULLEY 1
PULLEY 2
PULLEY 3 PULLEY 5
PULLEY 7
PULLEY 4
PULLEY 6
PULLEY 8
PULLEY 9
GEAR BELT
DRIVE BELT
BOTTLE FLOW
Page 78 / 170

PULLEY PAGE
FIGURE 24
A B C
8.9 CM 15.8 CM 12.3 CM
PULLEY (5)
(A)
(B)
(C)
PULLEY (7)
PULLEY (6)
PULLEY (1)
PULLEY (3) UPPER
PULLEY (2) LOWER
PULLEY (4)
PULLEY (9)
PULLEY (8)
PULLEY PAGE
FIGURE 24
PULLEY(1) 24HH100 30778
PULLEY(2) 28HH100 30781
PULLEY(3) 2AK46 36810
PULLEY(4) 2AK25 36806
PULLEY(5) 2AK34X1 30783
PULLEY(6) 2AK25X1 36806
PULLEY(7) 2AK61X1 36786
PULLEY(8) AK25X1 30660
PULLEY(9) AK30X3/4 30790
PULLEY(10) 16L050 24886
PULLEY(11) TENS. 38560
PULLEY(12) 16L050 24886
DUAL INFEED 2AK34 36845
TOP BAR INFEED IDLERS 3AK34 37065
TOP BAR HIGH SPEED IDLERS 2AK34 36845
TOP BAR EXIT IDLERS 2AK34 36845

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
BOTTLE FLOW
PULLEY (11)
PULLEY (10) PULLEY (12)
Page 79 / 170
MOTOR DRIVE PAGE
FIGURE 25
STAND-UP UNIT MOTOR 2 HP 46188
STAND-UP UNIT REDUCER 7.5:1 45992

DISC DRIVE MOTOR 1 HP 44507
DISC DRIVE REDUCER 30:1 46228
PULLEY (1) 4TB34 33940
PULLEY (2) 4TB64 33940
POWER RAMP MOTOR 1/8 HP 46035
ROTARY BUMPER MOTOR
ROTARY BUMPER REDUCER
3/8 HP 46802

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
* NOTE: THE LOCATION OF MOTOR&
REDUCER MAY BE DIFFERENT FROM
THE FIGURE SHOWN ABOVE.
DISC WALL
POLY DISC
PULLEY (1)
PULLEY (2)
DRIVE MOTOR
DRIVE REDUCER
STAND-UP UNIT
MOTOR
STAND-UP UNIT
REDUCER
ROTARY BUMPER
ROTARY BUMPER
MOTOR& REDUCER
Page 80 / 170
POWER RAMP DRIVE PULLEY
CENTER TOOLING BAR
POWER RAMP BELT & PULLEY PAGE
FIGURE 26
BELT OR PULLEY
NAME
DESC. PART NO.
POWER RAMP BELTS TWIN A 32180
POWER RAMP DRIVE
PULLEY
DRIVE
PULLEY
37179
POWER RAMP UPPER
PULLEY
CUSTOM 30132

POWER RAMP BELT
POWER RAMP UPPER PULLEY
BOTTLE FLOW
EXIT BOTTOM TOOLING
MOTOR
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
Page 81 / 170
DISC CONE

H W FOAM
DISC
FOAM
CONE
5.75" 48" N/A N/A
NOTE: THERE MAY BE MORE
RINGS THAN SHOWN IN THIS
PICTURE.
DISC DIMENSIONS # 1
DISC/RINGS
INNER RAD. OUTTER RAD.
T H
MAIN DISC 37" 1/4" 3 3/4"
RING 1 37" 41" 1/4" 3 3/4"/3"
RING 2 37" 42" 1/4" 3 3/4"/3"

H
W
R1
R2
R3
R4
R5
H
T1
T2
T3
T4
T5
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
FIGURE 27
Page 82 / 170
DISC WALL CUT OUT
FIGURE 28
BOTTLE
SIZE
A B C D E
ALL 24" 10 1/2" 16" 2" 6 1/4"

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
(C)
(B)
(D)
(E)
(A)
(B)
(C)
(E)
(A)
(D)
DISC WALL
CUT OUT
Page 83 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
INFEED HESITATOR BELT
FIGURE 30
Pulley # Description Part#
1 2AK41 31314
2 AS20X1/2 30902
3 AS20X1/2 30902
4 2AK41 31314
5 AS20X1/2 30902
6 AS20X1/2 30902
BELT# Description Part#
TRANSFER
BELTS
TWIN A 34702

(1)
(2) (3)
(4) (5)
(6)
BOTTLE FLOW
TRANSFER BELTS
BOTTLE FLOW
VIEW SHOWN
BOTTLE
FLOW
Page 84 / 170

BAO MAIN DRIVE
BELTS & PULLEYS
FIGURE 31
BELT OR
PULLEY #
DESCRIPTION PART#
BELT 1 570H100 30385
BELT 2 D850H100 30391
PULLEY 1 24HH100 30778
PULLEY 2 22HH100 30777
PULLEY 3 22HH100 30777
PULLEY 4 14HG100 20289
PULLEY 5 20HH100 31480
ALL TENSIONERS IDLER 34656
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TENSIONERS
PULLEY 3
PULLEY 4
PULLEY 5
BELT 2
BOTTLE FLOW

OPERATORS SIDE
BOTTLE FLOW
MOTOR
PULLEY 1
TENSIONER
PULLEY 2
BELT 1
Page 85 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
BOTTLE FLOW
TURNING BELT ASSEMBLY
FIGURE 32
Pulley # Description Part#
1 AK23X5/8" 30787
2 IDLER 22556
3 THRU 5 IDLER 25332
6 IDLER 22556
7 AK41X5/8 31148
8 AS20X1/2 30902
9 IDLER 22556
10 AS20X1/2 30902
11 AS20X1/2 30902
12 AS30X1/2 30993
BELT# Description Part#
TURNING BELT (NON-OP. SIDE) 3/8 ROUND 38226
TURNING BELT (OP. SIDE) 3/8 ROUND 37344

TURNING
TURNING BELT
BOTTLE FLOW
MOTOR
TURNING BELT
(OPERATOR SIDE)
PULLEY 1
PULLEY 3 THRU 5
PULLEY 2& 6
TURNING BELT
(NON-OPERATOR SIDE)
PULLEY 7
PULLEY 8
PULLEY 9
PULLEY 10
PULLEY 11
PULLEY 12
Page 86 / 170
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TURNING BELT ASSEMBLY
FIGURE 33
PULLEY H
1 0.2
2 0.1
3 0.1
4 0.1
5 0.1
6 0.1
7 1.5
8 2.2
9 0.5
10 2.2
11 1.8
12 1.6
TENSIONER
BRACKET
0.1

(H)
PULLEY HEIGHT
BOTTLE FLOW
MOTOR
TURNING BELT
(OPERATOR SIDE)
PULLEY 1
PULLEY 3 THRU 5
PULLEY 2& 6
TURNING BELT
(NON-OPERATOR SIDE)
PULLEY 7
PULLEY 8
PULLEY 9
PULLEY 10
PULLEY 11
PULLEY 12
Page 87 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
BAO BOTTOM CONVEYOR BELT &
PULLEY PAGE
FIGURE 34
BELT
OR PULLEY
BELT OR PULLEY
DESCRIPTION

PART #
PULLEY 1
TB16H100 22377
TENSIONER
IDLER 34656
TENSIONER
IDLER 34656
PULLEY 2
28HH100 30781
CONVEYOR
DRIVE BELT
970H100 38190

PULLEY 2
TENSIONER
TENSIONER
PULLEY 1
CONVEYOR
DRIVE BELT
BOTTOM CONVEYOR
BOTTLE FLOW
BOTTOM CONVEYOR DRIVE BELT
NON-OPERATORS
SIDE
BOTTLE FLOW
Page 88 / 170

TOP CONVEYOR DRIVE BELT
TOP CONVEYOR BELT
MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
TOP CONVEYOR PAGE ( FIGURE 35)
BELT
BELT
DESCRIPTION

PART #
TOP CONVEYOR DRIVE BELT 285L100 30379
TOP CONVEYOR BELT 800H200 36883
PULLEY 1 17LF100X3/4 25392
PULLEY 2 IDLER 34656
PULLEY 3 18LB100X3/4 25390

TOP CONVEYOR BELT
BOTTLE FLOW
TOP CONVEYOR DRIVE BELT
TOP
CONVEYOR
BELT
PULLEY 1
PULLEY 2
PULLEY 3
Page 89 / 170

MACHINE S/N:
3909&3910
CUSTOMER: COLGATE
DATE: 9/17/13
BAO MOTOR PAGE
FIGURE 36
BELT OR
PULLEY #
DESCRIPTION PART#
MAIN DRIVE
MOTOR
1 HP 44507
MAIN DRIVE
REDUCER
5:1 44388
INFEED MOTOR 1/8 HP 45936
INFEED
REDUCER
6:1 37088

TURNING BELT
MOTOR
1/8 HP 45936
TURNING BELT
REDUCER
200:1 37562

INFEED HESITATOR
MOTOR
BOTTLE FLOW
TURNING BELT MOTOR
MAIN DRIVE MOTOR
Page 90 / 170

MACHINE S/N:
3911
CUSTOMER: COLGATE
DATE: 9/17/13
HOPPER SPECIFICATION PAGE
FEATURE YES
OR NO
DIMENSION,LOCATION OR
PART #
A) HOPPER SIZE YES 170 CU FT
B) CHUTE YES #47050
C) COVERS YES
D) ELEVATOR BELT YES #46984
E) HORIZONTAL BELT YES #47223
F) CLEAN-OUT DOOR
(LOCATION)
NO
G) BRIDGE BREAKER
(LOCATION)
YES BOTH SIDES OF BIN
H) EXTENDED BIN
(EXTENDED FOR
HEIGHT)
NO
I) EXTENDED BIN
(EXTENDED FOR
LENGTH)
NO
J) FRAME EXTENSION NO
K) DROP LOAD GATE NO

MOTOR & REDUCER INFORMATION
MOTOR OR REDUCER DESCRIPTION PART #
ELEVATOR DRIVE MOTOR AC 1 HP 44507
ELEVATOR REDUCER 30:1 44093
HORIZONTAL DRIVE MOTOR AC 1HP 44507
HORIZONTAL REDUCER 60:1 44510
(D) ELEVATOR
BELT
REAR VIEWS OF THE HOPPER
(I)
(K) DROP
LOAD GATE
ELEVATOR REDUCER
ELEVATOR MOTOR
(H)
(G)
(D) ELEVATOR BELT (MADE UP OF 2 PIECES)
(J) FRAME
EXTENSION
HORIZONTAL
DRIVE MOTOR
HORIZONTAL REDUCER
(F) (G
(E) HORIZONTAL BELT
Page 91 / 170

SPARE PARTS LIST
SECTION VIII

Page 92 / 170

UNSCRAMBLER

Page 93 / 170
3 SPERRY ROAD
Fairfield, NJ 07004
973-227-1040

RECOMMENDED SPARE PARTS September 30, 2013
SPEC: STANDARD 800 W/POWER RAMP &HOOK S/N# 3909

AIR POWER

QUAN PART# DESCRI PTI ON
1 EA 33363 ROTARY ACTUATOR/ HOOK ASSY. ; 8MM

DRIVES

1 EA 44093 REDUCER; 30: 1; 56C; HOPPER ELEVATOR
1 EA 44510 REDUCER; 50: 1; HOPPER HORI ZI NTAL
1 EA 45992 REDUCER; 7. 5: 1; SUU
1 EA 46228 REDUCER; 30: 1; DI SC
1 EA 37088 GEARHEAD; 6: 1; SUU/ BAO TRANSFER
1 EA 46802 MOTOR/ REDUCER COMBO ROTARY BUMPER
3 EA 44507 MOTOR; 1HP; HOPPER, DI SC
1 EA 46188 MOTOR; 2HP; SUU
1 EA 45936 MOTOR; 1/ 8HP; SUU/ BAO TRANSFER
1 EA 46035 MOTOR; 90W; POWER RAMP

BELTS

1 EA 34806 BELT; TWI N A; VERT. ROTARY BUMP. DRI VE
1 EA 37524 BELT; TWI N A; I NFEED OPERATOR SI DE UPPER
1 EA 35438 BELT; TWI N A; I NFEED OPERATOR SI DE LOWER
1 EA 35478 BELT; TWI N A; I NFEED NON- OPER. SI DE
2 EA 34524 BELT; TWI N A; HI GH SPEED
2 EA 35400 BELT; TWI N A; EXI T
2 EA 34702 BELT; TWI N A; SUU/ BAO TRANSFER
1 EA 32180 BELT; TWI N A; POWER RAMP BELT
1 EA 30391 GEARBELT; D850H100
4 EA 35536 DRI VE BELT; SI NGLE A
2 EA 36277 BELT; B- 40
1 EA 46984 BELT; HOPPER ELEVATOR; 2 CLEAT
1 EA 47223 BELT; HOPPER HORI ZONTAL; FLAT

Page 94 / 170

3 SPERRY ROAD
Fairfield, NJ 07004
973-227-1040

RECOMMENDED SPARE PARTS Sept ember 30, 2013
SPEC: STANDARD 800 W/ POWER RAMP &HOOK S/ N# 3909

ELECTRICAL PARTS

1 EA 38167 AC DRI VE; 1HP
1 EA 38260 PHOTO ASSEMBLY POLARI ZED

MECHANICAL WEAR PARTS

2 EA 34656 PULLEY; GEARBELT I DLER ASSY
6 EA 34827 ROLLER
1 EA 36845 SHEAVE; 2AK34 I DLER ASSEMBLY
4 EA 32934 BLADE; ROTARY BUMPER
1 EA 33674 HOOK; GENERI C
Page 95 / 170

BAO 5000E

Page 96 / 170
3 SPERRY RD
Fairfield, NJ 07004
973-227-1040

RECOMMENDED SPARE PARTS, SERIAL NUMBER # 3910 October 14, 2013
ELECTRONIC BAO

DRIVES

1 EA 44507 MOTOR; 1HP; AC; MAI N DRI VE
3 EA 45936 MOTOR; 1/ 8 HP; SUU/ BAO TRANSFER, TURNI NG BELT
1 EA 44388 REDUCER; 5: 1; MAI N DRI VE
2 EA 37088 REDUCER; 6: 1; I NFEED
1 EA 37562 REDUCER; 200: 1; TURNI NG BELT

BELTS

1 EA 30391 GEARBELT; D850H100; NON- OP SI DE DRI VE
1 EA 30385 GEARBELT; 570H100; OP SI DE DRI VE
1 EA 38190 GEARBELT; 970H100; BOTTOM CONVEYOR DRI VE
1 EA 30379 GEARBELT; 285L100; TOP CONVEYOR DRI VE
1 EA 36883 GEARBELT; 800H200; TOP CONVEYOR
2 EA 34702 BELT; TWI N A; SUU/ BAO TRANSFER ( I NFEED)
1 EA 38226 BELT; 3/ 8 ROUND; TURNI NG BELT( NON- OPERATOR S SI DE)
1 EA 37344 BELT; 3/ 8 ROUND; TURNI NG BELT( OPERATOR S SI DE)

ELECTRICAL PARTS


MECHANICAL WEAR PARTS

1 EA 22556 SHEAVE; I DLER; 1 DI A X 1602SS
5 EA 20183 SPRI NG STEEL; BAO; TOP CONVEYOR

Page 97 / 170

HOPPER
Page 98 / 170
3 SPERRY ROAD
Fairfield, NJ 07004
973-227-1040

RECOMMENDED SPARE PARTS September 30, 2013
SPEC: CUSTOM HOPPER S/N# 3911

DRIVES

1 EA 44093 REDUCER; 30: 1; 56C; HOPPER ELEVATOR
1 EA 44510 REDUCER; 50: 1; HOPPER HORI ZI NTAL
2 EA 44507 MOTOR; 1HP; HOPPER

BELTS

1 EA 46984 BELT; HOPPER ELEVATOR; 2 CLEAT
1 EA 47223 BELT; HOPPER HORI ZONTAL; FLAT

ELECTRICAL PARTS


Page 99 / 170

ELECTRICAL SPECIFICATIONS
SECTION IX

Page 100 / 170
Page 101 / 170
Page 102 / 170
Page 103 / 170
Page 104 / 170
Page 105 / 170
Page 106 / 170
Page 107 / 170
Page 108 / 170
Page 109 / 170
Page 110 / 170
Page 111 / 170
Page 112 / 170
Page 113 / 170
Page 114 / 170
ELECTRICAL PARTS LIST
SN-3909-3910;M-800/BAO-5000
PACE P/N MAKE & MODEL DESCRI PTI ON QTY SCHEMATI C LOCATI ON CI RCUI T DESI GNATOR UL/CSA NUMBERS UL/CSA SYMBOL
24903 AB GREEN LIGHT ASSEMBLY LIGHT PILOT GREEN ASSEMBLY 1 S8/3 24 VOLT GREEN PILOT LIGHT (Q2)
23965 AB#800FP-P7PN3W PILOT LIGHT;WHITE 24 VDC 2 S5/4, S6/2 24 VOLT WHITE PANEL LIGHT E14840
24209 AB#800F-N3W MODULE; LED WHITE 4 S5/4, S6/2 24 VOLT WHITE PANEL LIGHT E14840
38677 HOFFMAN# A6AXFN24 FAN;COOLING;COMPACT;24V 1 S6/3 24V VENTING FAN
38678 HOFFMAN AGARD6 FINGER GUARD;USE W 38677 2 S6/3 24V VENTING FAN
24305 ATC#UPA-100 UNIVERSAL POWER ALERT 1 S1/6 480 VOLT PHASE INDICATOR
38172 AB#1783-US05T SWITCH;ETHER;5 PORT;UNMAN 1 S6/5, S7/2 5 PORT ETHRNET SWITCH
37902 AB#1783-US08T SWITCH;ETHER;8 PORT;UNMAN 1 S6/5-6, S7/1, S7/7 8 PORT ETHERNET SWITCH
37944 MS4N-EE-1/4-V24-S-AD1-WB-, FESTO VALVE;ON/OFF;FESTO/WITH PRESS-SEN 2 S9/8, S13/3 AD-2 , DISC AIR PRESSURE
38070 FESTO#151687 SOL;CONN;FESTO;USE W/37944 2 S9/8, S13/3 AD-2, DISC AIR SOLENIOD
37965 FESTO#548717 VALVE;DUMP;CAT 4 1 S9/9 AIR DUMP VALVE
37966 FESTO#548719 SOCKET MULTIPIN;USE W/ 37965 1 S9/9 AIR DUMP VALVE
37967 FESTO #552252 MUFFLER;SILENCER;USE W/37965 1 S9/9 AIR DUMP VALVE
37968 FESTO #526078 BASE;SUB;FESTO VALVE;USE W/ 37965 2 S9/9 AIR DUMP VALVE
37969 FESTO #526074 BRACKET;MOUNT;FESTO VALVE;USE W/37965 2 S9/9 AIR DUMP VALVE
37646 AB#855T-B24SA1 BEACON;ALARM SIN CIRCUIT 1 S12/3 ALARM E14840
23932 A.B.#855T-B24TL6 BEACON;STEADY BLUE LED A.B. 1 S12/3 BLUE BEACON E14840
24353 AB#1489-A3D250 CIRCUIT BREAKER;3P;25A 1 S1/2 CB-01 E197878
24786 AB#1489-A3D060 CIRCUIT BREAKER;3P;6A 7 S2/2, S2/5, S2/7, S3/2, S4/2, S4/5 CB-02, CB-03, CB-04, CB-06, CB-07, CB-08 E197878
24234 AB#1489-A3D100 CIRCUIT BREAKER;10A;3P 1 S3/2 CB-05 E197878
38570 COGNEX#CKR-4G-CBL-001 CABLE;PWR/IO;5M;USE W/38569 1 S6/10, S14/5 CHECKER 4G
38571 COGNEX#CCB-84901-1003-05 CABLE;ETHERNET;5M;USE/W 38569 1 S6/10, S14/5 CHECKER 4G
38640 COGNEX#C4G7-24X-E00 CAMERA;4G7X;VISION SENSOR 1 S6/10, S14/5 CHECKER 4G
47402 GRACE# P-R2-B3 PROGRAMMING PORT;ETHERNET ONLY 1 S7/1 CONVENIENCE INTERFACE
38544 AB#440G-MT47163 SWITCH;GUARD;LOCKING;24VDC 2 S8/3, S8/2, S12/8 DG1, DG2
38545 AB#889M-F12AH-10 CABLE;12PIN;M23;USE W/38544 2 S8/3, S8/2, S12/8 DG1, DG2
37973 FESTO#159421 CABLE;FESTO;USE W/37965 2 S6/1-2, S11/2 DISC AIR PRESSURE, MACHINE AIR PRESSURE, HOPPER AIR PRESSURE
47190 BANNER#WLS28CW285XPBQ LIGHT;STRIP;285MM;PUSH BUTTON 2 S6/8-9 ELECTRICAL BOX/MACHINE LIGHTING 3ZU0
47191 BANNER#MQDEC-403SS CABLE;DOUBLE ENDED;USE/W 46190 2 S6/8-9 ELECTRICAL BOX/MACHINE LIGHTING 3ZU0
47200 BANNER#WLS28CW285XQ LIGHT STRIP;285MM;CASCADE 2 S6/8-9 ELECTRICAL BOX/MACHINE LIGHTING 3ZU0
23953 AB#800FP-LMT44 MUSHROOM;TWIST A-B;LIGHTED 4 S8/3, S8/2, S9/3 E-STOP 1, E-STOP 2, E-STOP 3, E-STOP 4 E14840
24014 AB#800F-X10 SWITCH;BLOCK N.O.CONTACTS 4 S8/3, S8/2, S9/3 E-STOP 1, E-STOP 2, E-STOP 3, E-STOP 4 E14840
24015 AB#800F-X01 SWITCH;BLOCK N.C.CONTACTS 4 S8/3, S8/2, S9/3 E-STOP 1, E-STOP 2, E-STOP 3, E-STOP 4 E14840
24095 AB#800F-N3R MODULE;RED LED A-B 4 S8/3, S8/2, S9/3 E-STOP 1, E-STOP 2, E-STOP 3, E-STOP 4 E14840
23934 A.B.#800FPX01 SWITCH;Cont/Latch nc X01 5 S8/3, S8/2, S9/3, S9/10 E-STOP 1, E-STOP 2, E-STOP 3, E-STOP, 4, S6 E14840
24697 AB#598-1PB22Y BOX;PUSH BUTTON;PLASTIC YELLOW 2 S9/3 E-STOP 3, E-STOP 4 E14840
37791 AB#1768-ENBT ETHERNET/IP BRIDGE L4X 2 S7/1 ETHERNET
37666 AB#440R-H23178 RELAY;SAFETY EXPAN UNIT 10 S8 EXP-1, EXP-2, EXP-3, EXP-4, EXP-5, EXP-6, EXP-7, EXP-8, EXP-9, EXP-10
24475 FUSECO#GMC 10 FUSE;GLASS;10A;5x20MM 2 S1/7 F-01, F-02 E19180
24381 AB#1492-WFB424 SINGLE CKT. FUSE BLOCK 19 S1/7, S5/5-7, S6/3, S6/4, S6/5, S6/6, S6/7, S6/8, S6/9, S6/10, S9/3, S9/5, S9/6, S9/7-8 F-01-F-05A, F06-F18 E40735
24355 FUSECO#GDG2 GRAIN#1CD13 FUSE,GLASS;2A;5X20MM;GDG2 7 S6/3, S6/5, S6/6, S6/8, S6/9, S9/3, S9/8 F-03, F-05, F-05A, F-07, F-08, F-10, F-18 E19180
24459 FUSECO#GDB-3.15A FUSE;3.15A;5X20MM 1 S6/4 F-04 E19180
24359 FUSECO GDC6.3 FUSE;6.3A; 5x20;GDC-6.3 1 S6/7 F-07 E19180
24458 FUSECO#GDB400MA FUSE;400MA;5X20MM 5 S6/10, S9/5, S9/6 F-10, F-11, F-12, F-13, F-14 E19180
24672 FUSECO#GDC80MA FUSE;8/100 AMP;5x20; GLASS 2 S9/8 F-16, F-17 E19180
24727 FUSECO#GDG1 FUSE; 1 AMP; 5 X 20MM 1 S9/8 F-17 E19180
24480 FUSECO#ATMR-1/10 FUSE;.100 A; FAST BLOW 3 S1/4 FB-09 Standard 248-4
23665 AB #1492-FB3C30-L FUSE HLDR;3 BANK;AB 3 S1/4 FB-09, FB-10, FB-11 E34648
24452 FUSECO#ATQR6 FUSE;6A;FNQ-R-6 6 S1/4 FB-11, FB-12 Standard 248-4
23878 A.B. #855T-B24TL3 BEACON;STEADY GREEN LED A.B. 1 S12/3 GREEN BEACON E14840
37794 AB#1769-IQ32 INPUT MOD;32PT;24VDC 2 S7/2, S7/3, S10, S11 INPUT 1, INPUT 2
24669 LAPP#10399100 CONN; 4 CONTACT ; RECEPTACLE 3 S13 J1 & J2
38108 LAPP#11195300 SOCKET;2.5MM 12 S13 J1 & J2
24656 LAPP#10382500 CONN;10 CONTACT RECEPTACLE 6 S13 J1, J2, J3, J3A
24658 LAPP#13163200 CONN; SOCKET; 1.6MM 60 S13 J1, J2, J3, J3A
24666 LAPP#10381300 FRAME; 3 MODULE; RECEPTACLE 1 S13 J2
24664 LAPP#10381100 FRAME; 2 MODULE; RECEPTACLE 2 S13 J3, J3A
37735 AB#100S-C09EJ 14BC CONTACTOR;SAFETY;2HP 2 S 9/6 K1, K2
24635 AB#100-K09DJ 10 CONTACTOR;24VDC MINIATURE 2 S13/3 K3, K4
24676 AB#700HLT12Z24 RELAY;TERMINAL BLOCK;2-POLE 3 S12/3, S12/8 K5, K6, K8
24633 AB#700-K22Z-DJ RELAY;4 POLE 24VDC A-B 2NO, 2NC 1 S12/8 K7 E33916
37730 AB#440R-H23176 RELAY;MINOTAUR;SAFETY 1 S9/4 K9
22592 BANNER #RS8 SOCKET;SPEC. FOR 22593 2 S14/5 LL-1, LL-2 E71083
22593 MICRO-AMP MA4L LOGIC MODULE;LATCH 2 S14/5 LL-1, LL-2 E71083
24972 AB#800B-EPC LIGHT PILOT RECTANGLE 3 S12/3 LOW AIR PANEL LIGHTS
24973 AB#800B-ALC5 LENS CAP W/DIFFUS RECT;YELLOW 3 S12/3 LOW AIR PANEL LIGHTS
24974 AB#800B-PL PILOT LIGHT/DUMMY BLOCK 3 S12/3 LOW AIR PANEL LIGHTS
24975 AB#800B-N3W LED/WHITE 3 S12/3 LOW AIR PANEL LIGHTS
44507 MARATHON #G583 MTR;1HP;230/460VAC 56C 4 S2/2, S2/5, S3/5, S4/10 M1, M2, M7, M9 E49747, LR 2025
46802 BODINE #2862 MTR;3/8HP;3PH;220/460;170 RPM;60HZ 1 S27 M3
46188 MARATHON#P106 MTR;2HP;60HZ;3600 RPM 1 S2/8 M4 E49747, LR 2025
Page 115 / 170
SN-3909-3910;M-800/BAO-5000
46035 SPG; S9190DS-TCE;PWR RAMP MTR;90W;480V;RD SHAFT;PWR 1 S3/2 M5 THERMALLY PROTECTED
37088 SPG #S9DC6BHA-R30 GEARHEAD;6:1;300RPM 1/2" 2 S3/2 S3/4 M6, M6A MECHANICAL DEVICE
45936 SPG#S9190GSH-TCE MTR;1/8HP;480V;SPG 3 S3/2 S3/4, S3/8 M6, M6A, M8 THERMALLY PROTECTED
37562 SPG#S9KC200BHA GEARHEAD;200:1; 5/8" 1 S3/8 M8 N/A
37970 FESTO #192028 SENSOR;PRESSURE;USE W/ 37965 1 S6/1, S11/2 MACHINE AIR PRESSURE
24833 AB#140M-C2E-A40 CIRCUIT BREAKER;MOT PROT;.25-.65A 1 S3/7 MS1 LISTED IND. CONT. EQ. 728B
24832 AB#140M-C-ASA11 CONTACT;AUX;SIDE;FOR 140M 2 S3/8, S3/10, S11/8 MS1, MS2 LISTED IND. CONT. EQ. 728B
24835 AB#140M-C2E-B25 Circuit Breaker Mot Prot;1.6-2.5A 1 S3/9 MS2 LISTED IND. CONT. EQ. 728B
20013 RED DOT AC-1 FTG;CONDUIT;PULL;ST;1/2 2 N/A N/A E30640
20014 OLFLEX #1212 FTG;STRAIN RELIEF;1/2" 5 N/A N/A E146370
20018 RED DOT SCV-1 STAMPED AL. FTG;1/2;CONDUIT COVER 3 N/A N/A E30640
20020 RED DOT MUL 11720 FTG;CONDUIT COVER SEAL 3 N/A N/A E30640
20027 VICTOR 11102-S CLAMP;1/4" 10 N/A N/A N/A N/A
20050 040-A1-C CAPITAL HWAY PE;REFLECTOR;3-1/4IN 10 N/A N/A N/A N/A
20320 OLFLEX S-1112 GRAY CONN;STR;STRLF;1/2" 10 N/A N/A E146370
20331 T&B;141 LOCKNUT;1/2IN 9 N/A N/A E 23018
20332 T&B;142 LOCKNUT;3/4;T&B 142 4 N/A N/A E 23018
20333 T&B 222 OR BRIDGEPORT 321 BUSHNG;1/2;PLASTIC INSUL 4 N/A N/A E9391/LR39354
20368 RED DOT AT-1 COND;OUTLET BOX;.5" T;THR 2 N/A N/A E30640
20530 THOMAS & BETTS #5262 SEAL;1/2" CONDUIT 9 N/A N/A E 13938
22721 LEGEND;START;1/2 X 1 1 N/A N/A N/A N/A
22722 LEGEND;STOP;1/2 X 1 1 N/A N/A N/A N/A
23200 PACE MADE LEGEND;RESET;1/2 X 1 2 N/A N/A N/A N/A
23238 ABB #SK615546-2 LEGEND;ESTOP;RND.YELLOW 4 N/A N/A N/A N/A
23392 #6010B-ISO TRIANGLE LABEL;ELECT.HI VOLT.SYMBO 1 N/A N/A N/A N/A
23941 A.B. #1492-ERL35 TERM.BLOCK;END BRACKET 5 N/A N/A E40735
24361 AB#1492-WTF3 THREE LEVEL SENSOR BLOCK 112 N/A N/A E40735
24363 AB#1492-CJ T5-50 50 POLE CENTER J UMPER 2 N/A N/A E40735
24382 AB#1492-SJ FB8-10 SIDE J UMPER 3 N/A N/A E40735
24404 AB#1489-AACL318 J UMPER;STRIP;3P;6 CKT 2 N/A N/A E305318
24447 AB#1492-SJ FB8-10 J UMPER;FUSE 3 N/A N/A E34648, E40735, E160646
24465 SAG#SCE-606ELJ SS BOX;SS; 6x6x4 1 N/A N/A E69392
24466 SAG#SCE-6P6J PANEL; USE W/24465 1 N/A N/A E69392
24499 855T-BSPM40C BEACON;POL;BASE A.B;40CM 1 N/A N/A E14840
24544 ALTECH#3P16UL3/12 BUSBAR;3 PHASE;12 PIN 1 N/A N/A E305318
24545 ALTECH#P50ULB MODULAR DIRECT POWER FEED 3 N/A N/A E305318
24814 AB#1492-J G6 TERM BLOCK;GRE/YELL;10GA 15 N/A N/A E40735
37654 AB#1769-ECR MICROLOGIX; RT END CAP 1 N/A N/A
38160 LASNEK#K33-03 WIREWAY;3X3;3M; SS SATIN 3 N/A N/A File No. 206295
38161 LASNEK#K33-16 WIREWAY;3X3;45;INSIDE COVER 2 N/A N/A File No. 206295
38162 LASNEK #K33-17 WIREWAY;3X3;45;OUTSIDE COVER 2 N/A N/A File No. 206295
38163 LASNEK #K33-25 WIREWAY;FLANGE ADAPTER 3X3 2 N/A N/A File No. 206295
38164 LASNEK#K33-21 WIREWAY;END CAP; 3X3 2 N/A N/A File No. 206295
38165 LASNEK#X33-22 WIREWAY;STR;COUPLING;3X3 2 N/A N/A File No. 206295
46161 SAG#SCE-PWK2315NF WINDOW KIT; 23x15 4 N/A N/A E69392
46165 SCE-FGA66 FILTER & GRILLE ASSY 2 N/A N/A E69392
46170 SCE-105604 INTERLOCK;MECHANICAL 1 N/A N/A E69392
46464 SAG#72EL6012LPPL BOX; ELEC;72X60X12; 1 N/A N/A E69392
46465 SAG#72P60 PANEL;72X60;USE/W 46464 1 N/A N/A E69392
37992 AB#193-ERR REMOTE RESET MODULE 2 S4/2-3, S5/9-10, S10/8 OL1, OL2
37993 AB#193-EEBB RELAY;OVERLOAD SOLID STATE 2 S4/2-3, S5/9-10, S10/8 OL1, OL2
37994 AB#193-BC8 CURRENT ADJ USTMENT SHIELD 2 S4/2-3, S5/9-10, S10/8 OL1, OL2
37995 AB#193-EPB DIN RAIL PANEL ADAPTER 2 S4/2-3, S5/9-10, S10/8 OL1, OL2
24148 AB# 855T-B24TL5 BEACON; AMBER STEADY LED AB 1 S12/3 ORANGE BEACON E14840
37822 AB#1769-OB16 Compact Logix Output Module; 16 Out Positive 3 S7/4, S12-1, S12-7, S13/1 OUTPUT 1, OUTPUT 2, OUTPUT 3
37731 AB#440R-H23180 RELAY;MINOTAUR;OUT;EXP 2 S9/6-8 OUTPUT EXP 1, OUTPUT EXP 1
24849 LAPP#10381400 CONN;5 MODULE;MALE 1 S13 P1 & J1
24850 LAPP#10381500 CONN;5 MODULE;FEMALE 1 S13 P1 & J1
24867 LAPP#100739C00 PANEL MOUNT;BASE 5 MODULE 1 S13 P1 & J1
24868 LAPP#10381400 FRAME;PLUG;5 MODULE 1 S13 P1 & J1
24869 LAPP#10381500 FRAME;RECPT;5 MODULE 1 S13 P1 & J1
24870 LAPP#700944NP HOOD; HIGH PROFILE;1" 1 S13 P1 & J1
24668 LAPP#10399000 CONN; 4 CONTACT ; PLUG 3 S13 P1 & P2
38107 LAPP#11190300 PIN; 2.5MM 12 S13 P1 & P2
24655 LAPP#10382400 CONN;10 CONTACT PLUG 6 S13 P1 , P2, P3
24657 LAPP#13162200 CONN; PIN; 1.6MM 60 S13 P1 , P2, P3
24665 LAPP #10381200 FRAME; 3 MODULE; PLUG 1 S13 P2
24667 LAPP#700442NP HOOD; TOP ENTRY ;3 POLE 1 S13 P2 & J2
38106 LAPP#10033900 PANEL MOUNT BASE HBE 10, 3 POLE 1 S13 P2 & J2
24663 LAPP#10381000 FRAME;2 MODULE; PLUG 2 S13 P3
38104 LAPP#100040C0 BOX MOUNT BASE 2 POLE W/DUST COVER 2 S13 P3, J3, J3A
Page 116 / 170
SN-3909-3910;M-800/BAO-5000
38105 LAPP#700202NP HOOD;HIGH PROFILE;2 POLE TOP ENTRY 2 S13 P3, J3, J3A
37494 AB#2711P-T6C20D HMI;PANEL VIEW 600 COLOR 1 S6/4, S7/3 PANEL VIEW 600 E10314
37903 AB#22-COMM-E COMM;ADAPT;ETHERNET 8 S7/5-10 PART OF U1, U2, U3, U4, U5, U6, U7 E59272
38141 AB#20A-DG01 DRIVE GUARD SAFE-OFF BOARD 8 S2/2, S2/4, S2/7, S2/9, S3/2, S4/2, S4/5 PART OF U1, U2, U3, U4, U5, U6, U7
38170 AB#22D-CCB AC DRV;PFLEX40P;COVER 7 S2/2, S2/4, S2/7, S2/9, S3/2, S4/2, S4/5 PART OF U1, U2, U3, U4, U5, U6, U7
38171 AB#22-RF012-BS AC DRV;PFLEX40P;FILTER 7 S2/2, S2/4, S2/7, S2/9, S3/2, S4/2, S4/5 PART OF U1, U2, U3, U4, U5, U6, U7
38260 RETRO REFLECTIVE PE;ASSY;NEW;QD;TRANS OUT;EURO 7 S11/2, S11/8 PC-1, PC-2, PC-3, PC-4, PC-5, PC-6. PC-7, PC-8 E71083
38278 FIBER OPTIC PE;ASSY;FO:NEW BANNER PARTS 3 S14/4, S14/8 PC-9, PC-10, PC-11 E71083
37793 AB#1768-PB3 POWER SUPPLY;CMPT LOGIX 1 S7/0 PLC POWER SUPPLY
38694 AB# 1768-L45 PROCESSOR;3M MEMORY;L45 1 S7/2 PROCESSOR
37622 AB#1606-XL240E-3 POWER SUPPLY;3PH; 480V 10 AMP 2 S1/6 PS-1, PS-2 E56639, CE, UL508 (cULus LISTED), UL1950 (cURus),
24388 AB#194E-A63-1753-6N FRNT MOUNT DIS SWITCH;63A 1 S1/1 Q1 E54612 NLRV
24601 AB#194E-A63-PE TERM;EARTH/GROUNDING 1 S1/1 Q1 E54612 NLRV
24813 AB#194E-40-C3 TERM COVER;3POL;40 TO 63 AMP 2 S1/1 Q1 E54612 NLRV
23343 23340)AB 194E-G3675 SWITCH;METAL SHAFT(PRT OF 2 S1/1, S8/4 Q1, Q2 E14840
34911 AB #194R-HS4E-N2 SWITCH;HANDLE;A-B RED/YELLOW 2 S1/1, S8/4 Q1, Q2 E14841
23940 AB#194E-A-P11 USE W/36376 DISCONNECT;AUX CON; A.B 1 S8/4 Q2 E14841
36376 AB 194E-A32-1753-6N SWITCH;AB;DISCON/ HANDLE 1 S8/4 Q2 E14841
23879 A.B. #855T-B24TL4 BEACON;STEADY RED LED A.B. 1 S12/3 RED BEACON E14840
23972 AB#800FP-LF6 SWITCH;LITED PUSH BLUE AB 1 S9/5, S11/2 RESET BUTTON E14840
24397 A.B.#800FP-F6 PUSH BUTTON;BLUE FLUSH 1 S9/10 S6 E14840
24092 AB#800FP-LF3 SWITCH;GREEN FLUSH LIGHTED AB 1 S11/2 START BUTTON E14840
24096 AB#800F-N3G MODULE;GREEN LED 1 S12/3 START BUTTON E14840
23935 A.B.#800FPX10 SWITCH;Cont/Latch no X10 5 S11/2 START BUTTON, STOP BUTTON, RESET BUTTON, JOG BUTTONS E14840
24396 A.B.#800FP-E2 PUSH BUTTON;BLACK EXTEND 1 S11/2 STOP BUTTON E14840
24094 AB#800FP-F5 PUSH BUTTON;YELLOW A-B 2 S11/2 TWO HANDED JOG E14840
24391 AB#800F-P25 2 HOLE PENDANT STATION 1 S11/2 TWO HANDED JOG E14840
36888 CABLE SCIENCE NCJ 184-20 CORD;RETRACTILE;YELLOW 1 S11/2 TWO HANDED JOG
38167 AB#22D-D2P3N104 AC DRV;PFLEX40P;1HP;480V 6 S2/2, S2/4, S2/7, S3/2, S4/2, S4/5 U1, U2, U3, U5, U6, U7
38168 AB#22D-D4P0N104 AC DRV;PFLEX40P;2HP;480V 1 S2/9 U4
37598 889D-F8AB-10 CORDSET;QD;DC MICRO;10m 15 S8 WG1-WG15
37987 AB#440N-Z21W1PH SWITCH;NON CONTACT; 8 PIN CODED 15 S8 WG1-WG15
Page 117 / 170

3 PHASE
480 VOLT
F-01
F-02
F-03
F-04
F-05
EXP-1 EXP-3 EXP-5 EXP-7
K9
OUTPUT
MOD 1
OUTPUT
MOD 2
INPUT
MOD 2
POWER
SUPPLY
5 PORT
SWITCH
8 PORT
SWITCH
INPUT
MOD 1
CPU
CB-01
F-06
F-07
PS-1
+24 VOLT
PS-2
+24 VOLT
AC DRIVE 3
U3
BUMPER
AC DRIVE 5
U5
POWER
RAMP
AC DRIVE 6
U6
INFEED
AC DRIVE 7
U7
BAO
AC DRIVE 2
U2
DISC
AC DRIVE 1
U1
HOPPER

OL1
K1
OL2
K2
EXP-2 EXP-4 EXP-6
MS1
F-14
F-15
F-16
F-17
F-12
F-13
CB-06
FB-09 CB-07
CB-08
FB-10
FB-11
LL-1
CB-02
CB-03
CB-04
CB-05
SN-3909-3910
18 OF 18
OUT-1
F-08
F-18
LL-2
K3
PS-1
+24 VOLT
PS-2
+24 VOLT
K8
K7
AC DRIVE 4
U4
STANDUP
EXP-10
Q1
ETHERNET
PORT 2
ETHERNET
PORT 1
MS2
K4
F-11
F-10
F-09
PE
GRD
K5
K6
EXP-8
OUTPUT
MOD 3
OUT-2
EXP-9
F-05A
Page 118 / 170
Parameter List - PowerFlex 40P - VFD_Hopper Page 1
All Parameters 9/11/2013 5:10:28 PM
C:\USERS\USER1\DESKTOP\PACE_3909\Pace_3910.ACD
ID Name Value Units Internal Value
1 Output Freq 0.00 Hz 0
2 Commanded Freq 20.00 Hz 2000
3 Output Current 0.00 A 0
4 Output Voltage 0.0 V 0
5 DC Bus Voltage 652 V 652
6 Drive Status 0000000000000010 2
7 Fault 1 Code 4 4
8 Fault 2 Code 71 71
9 Fault 3 Code 4 4
10 Process Display 0 0
11 Process Fract 0.00 0
12 Control Source 52 52
13 Contrl In Status 0000000000000000 0
14 Dig In Status 0000000000000000 0
15 Comm Status 0000000000000101 5
16 Control SW Ver 0.00 0
17 Drive Type 0 0
18 Elapsed Run Time 0 x10h 0
19 Testpoint Data 0000000000000000 0
20 Analog In 0-10V 0.0 % 0
21 Analog In 4-20mA 0.0 % 0
22 Output Power 0.00 kW 0
23 Output Powr Fctr 0.0 deg 0
24 Drive Temp 28 C 28
25 Counter Status 0 0
26 Timer Status 0 Sec 0
27 Timer Stat Fract 0.0 0
28 Stp Logic Status 0 0
29 Torque Current 0.00 A 0
30 Reserved 0 0
31 Motor NP Volts 460 V 460
32 Motor NP Hertz 60 Hz 60
33 Motor OL Current 1.4 A 14
34 Minimum Freq 0.00 Hz 0
35 Maximum Freq 60.00 Hz 6000
36 Start Source Comm Port 5
37 Stop Mode Ramp, CF 0
38 Speed Reference Comm Port 5
39 Accel Time 1 1.0 Sec 10
40 Decel Time 1 1.0 Sec 10
41 Reset To Defalts Ready/Idle 0
42 Reserved 0 0
43 Motor OL Ret Disabled 0
44 Reserved 0 0
45 Reserved 0 0
46 Reserved 0 0
47 Reserved 0 0
RSLogix 5000
Page 119 / 170
48 Reserved 0 0
49 Reserved 0 0
50 Reserved 0 0
51 Digital In1 Sel Preset Freq 4
53 Digital In3 Sel Clear Fault 7
54 Digital In4 Sel Jog Forward 11
55 Relay Out Sel Ready/Fault 0
56 Relay Out Level 0 0
57 Relay Out LevelF 0.0 0
58 Opto Out1 Sel MotorRunning 2
59 Opto Out1 Level 0 0
60 Opto Out1 LevelF 0.0 0
61 Opto Out2 Sel At Frequency 1
64 Opto Out Logic 1=NO / 2=NO 0
65 Analog Out Sel OutFreq 0-10 0
66 Analog Out High 100 % 100
69 Internal Freq 60.00 Hz 6000
70 Preset Freq 0 0.00 Hz 0
78 Jog Frequency 10.00 Hz 1000
79 Jog Accel/Decel 10.0 Sec 100
80 DC Brake Time 0.0 Sec 0
81 DC Brake Level 0.1 A 1
82 DB Resistor Sel Disabled % 0
83 S Curve % 0 % 0
84 Boost Select 5.0, CT 8
85 Start Boost 2.5 % 25
86 Break Voltage 25.0 % 250
87 Break Frequency 15.0 Hz 150
88 Maximum Voltage 460 V 460
89 Current Limit 1 3.5 A 35
90 Motor OL Select No Derate 0
91 PWM Frequency 4.0 kHz 40
92 Auto Rstrt Tries 0 0
93 Auto Rstrt Delay 1.0 Sec 10
94 Start At PowerUp Disabled 0
RSLogix 5000
Page 120 / 170
95 Reverse Disable REV Enabled 0
96 Flying Start En Disabled 0
97 Compensation Electrical 1
98 SW Current Trip 0.0 A 0
99 Process Factor 30.0 300
100 Fault Clear Ready/Idle 0
101 Program Lock 0 0
102 Testpoint Sel 0000010000000000 1024
103 Comm Data Rate 9600 3
104 Comm Node Addr 100 100
105 Comm Loss Action Fault 0
106 Comm Loss Time 5.0 Sec 50
107 Comm Format RTU 8-N-1 0
108 Language English 1
109 Anlg Out Setpt 0.0 % 0
110 Anlg In 0-10V Lo 0.0 % 0
111 Anlg In 0-10V Hi 100.0 % 1000
112 Anlg In4-20mA Lo 0.0 % 0
113 Anlg In4-20mA Hi 100.0 % 1000
114 Slip Hertz @ FLA 0.0 Hz 0
115 Process Time Lo 0.00 0
116 Process Time Hi 0.00 0
117 Bus Reg Mode Enabled 1
119 Skip Frequency 0 Hz 0
120 Skip Freq Band 0.0 Hz 0
121 Stall Fault Time 60 Seconds 0
122 Analog In Loss Disabled 0
123 10V Bipolar Enbl Uni-Polar In 0
124 Var PWM Disable Enabled 0
125 Torque Perf Mode Sensrls Vect 1
126 Motor NP FLA 1.5 A 15
127 Autotune Ready/Idle 0
128 IR Voltage Drop 13.0 Vac 130
129 Flux Current Ref 0.75 A 75
130 PID Trim Hi 60.0 Hz 600
131 PID Trim Lo 0.0 Hz 0
132 PID Ref Sel PID Disabled 0
133 PID Feedback Sel 0-10V Input 0
134 PID Prop Gain 0.01 1
135 PID Integ Time 2.0 Sec 20
136 PID Diff Rate 0.00 1/s 0
137 PID Setpoint 0.0 % 0
138 PID Deadband 0.0 % 0
139 PID Preload 0.0 Hz 0
140 Stp Logic 0 0000000011110001 241
141 Stp Logic 1 0000000011110001 241
RSLogix 5000
Page 121 / 170
142 Stp Logic 2 0000000011110001 241
143 Stp Logic 3 0000000011110001 241
144 Stp Logic 4 0000000011110001 241
145 Stp Logic 5 0000000011110001 241
146 Stp Logic 6 0000000011110001 241
147 Stp Logic 7 0000000011110001 241
148 Reserved 0 0
149 Reserved 0 0
150 Stp Logic Time 0 30.0 Sec 300
158 Reserved 0 0
159 Reserved 0 0
160 EM Brk Off Delay 2.00 Sec 200
161 EM Brk On Delay 2.00 Sec 200
162 MOP Reset Sel Save MOP Ref 1
163 DB Threshold 100.0 % 1000
164 Reserved 0 0
165 Reserved 0 0
166 Reserved 0 0
167 Reserved 0 0
168 Reserved 0 0
169 Reserved 0 0
170 Reserved 0 0
171 Reserved 0 0
172 Reserved 0 0
173 Reserved 0 0
174 Reserved 0 0
175 Reserved 0 0
176 Reserved 0 0
177 Reserved 0 0
178 Reserved 0 0
179 Reserved 0 0
180 Reserved 0 0
181 Reserved 0 0
182 Reserved 0 0
183 Reserved 0 0
184 Reserved 0 0
185 Reserved 0 0
186 Reserved 0 0
187 Reserved 0 0
188 Reserved 0 0
RSLogix 5000
Page 122 / 170
189 Reserved 0 0
190 Reserved 0 0
191 Reserved 0 0
192 Reserved 0 0
193 Reserved 0 0
194 Reserved 0 0
195 Reserved 0 0
196 Reserved 0 0
197 Reserved 0 0
198 Reserved 0 0
199 Reserved 0 0
200 Reserved 0 0
201 LED Display Opt 1-7,10 Only 2
202 Digital Term 3 Start Source 0
207 Comm Write Mode Save 0
208 Power Loss Mode Coast 0
209 Half Bus Enable Disabled 0
210 Max Traverse 0.00 Hz 0
211 Traverse Inc 0.00 Sec 0
212 Traverse Dec 0.00 Sec 0
213 P Jump 0.00 Hz 0
214 Sync Time 0.0 Sec 0
215 Speed Ratio 1.00 100
216 Motor Fdbk Type None 0
217 Motor NP Poles 4 4
218 Encoder PPR 1024 PPR 1024
219 Pulse In Scale 64 64
220 Ki Speed Loop 2.0 20
221 Kp Speed Loop 0.5 5
222 Positioning Mode Time Steps 0
223 Find Home Freq 10.0 Hz 100
224 Find Home Dir Forward 0
225 Encoder Pos Tol 100 100
226 Counts Per Unit 4096 4096
227 Reserved 0 0
228 Reserved 0 0
229 Reserved 0 0
230 Step Units 0 0 0
231 Step Units F 0 0.00 0
RSLogix 5000
Page 123 / 170
246 Pos Reg Filter 8 8
247 Pos Reg Gain 3.0 30
248 Enh Control Word 0000000000000000 0
249 Cmd Stat Select Velocity 0
250 Reserved 0 0
251 Reserved 0 0
252 Reserved 0 0
253 Reserved 0 0
254 Reserved 0 0
255 Reserved 0 0
256 Reserved 0 0
257 Reserved 0 0
258 Reserved 0 0
259 Reserved 0 0
260 Reserved 0 0
261 Reserved 0 0
262 Reserved 0 0
263 Reserved 0 0
264 Reserved 0 0
265 Reserved 0 0
266 Reserved 0 0
267 Reserved 0 0
268 Reserved 0 0
269 Reserved 0 0
270 Reserved 0 0
271 Reserved 0 0
272 Reserved 0 0
273 Reserved 0 0
274 Reserved 0 0
275 Reserved 0 0
276 Reserved 0 0
277 Reserved 0 0
278 Reserved 0 0
279 Reserved 0 0
280 Reserved 0 0
281 Reserved 0 0
282 Reserved 0 0
RSLogix 5000
Page 124 / 170
283 Reserved 0 0
284 Reserved 0 0
285 Reserved 0 0
286 Reserved 0 0
287 Reserved 0 0
288 Reserved 0 0
289 Reserved 0 0
290 Reserved 0 0
291 Reserved 0 0
292 Reserved 0 0
293 Reserved 0 0
294 Reserved 0 0
295 Reserved 0 0
296 Reserved 0 0
297 Reserved 0 0
298 Reserved 0 0
299 Reserved 0 0
300 Reserved 0 0
301 Drive Status 2 0000000000000000 0
302 Fiber Status 0000000000000000 0
303 Slip Hz Meter 0.0 Hz 0
304 Speed Feedback 0 RPM 0
305 Speed Feedback F 0.0 RPM 0
306 Encoder Speed 0 RPM 0
307 Encoder Speed F 0.0 RPM 0
308 Units Traveled H 0 0
309 Units Traveled L 0.00 0
RSLogix 5000
Page 125 / 170
Parameter List - PowerFlex 40P - VFD_Disc Page 1
6 Drive Status 0000000000000010 2
7 Fault 1 Code 4 4
9 Fault 3 Code 4 4
13 Contrl In Status 0000000000000000 0
14 Dig In Status 0000000000000000 0
15 Comm Status 0000000000000101 5
17 Drive Type 0 0
19 Testpoint Data 0000000000000000 0
20 Analog In 0-10V 0.0 % 0
21 Analog In 4-20mA 0.0 % 0
24 Drive Temp 0 C 0
30 Reserved 0 0
42 Reserved 0 0
44 Reserved 0 0
45 Reserved 0 0
46 Reserved 0 0
47 Reserved 0 0
RSLogix 5000
Page 126 / 170
48 Reserved 0 0
49 Reserved 0 0
50 Reserved 0 0
83 S Curve % 0 % 0
RSLogix 5000
Page 127 / 170
102 Testpoint Sel 0000010000000000 1024
110 Anlg In 0-10V Lo 0.0 % 0
111 Anlg In 0-10V Hi 100.0 % 1000
112 Anlg In4-20mA Lo 0.0 % 0
113 Anlg In4-20mA Hi 100.0 % 1000
140 Stp Logic 0 0000000011110001 241
141 Stp Logic 1 0000000011110001 241
RSLogix 5000
Page 128 / 170
142 Stp Logic 2 0000000011110001 241
143 Stp Logic 3 0000000011110001 241
144 Stp Logic 4 0000000011110001 241
145 Stp Logic 5 0000000011110001 241
146 Stp Logic 6 0000000011110001 241
147 Stp Logic 7 0000000011110001 241
148 Reserved 0 0
149 Reserved 0 0
158 Reserved 0 0
159 Reserved 0 0
163 DB Threshold 100.0 % 1000
164 Reserved 0 0
165 Reserved 0 0
166 Reserved 0 0
167 Reserved 0 0
168 Reserved 0 0
169 Reserved 0 0
170 Reserved 0 0
171 Reserved 0 0
172 Reserved 0 0
173 Reserved 0 0
174 Reserved 0 0
175 Reserved 0 0
176 Reserved 0 0
177 Reserved 0 0
178 Reserved 0 0
179 Reserved 0 0
180 Reserved 0 0
181 Reserved 0 0
182 Reserved 0 0
183 Reserved 0 0
184 Reserved 0 0
185 Reserved 0 0
186 Reserved 0 0
187 Reserved 0 0
188 Reserved 0 0
RSLogix 5000
Page 129 / 170
189 Reserved 0 0
190 Reserved 0 0
191 Reserved 0 0
192 Reserved 0 0
193 Reserved 0 0
194 Reserved 0 0
195 Reserved 0 0
196 Reserved 0 0
197 Reserved 0 0
198 Reserved 0 0
199 Reserved 0 0
200 Reserved 0 0
213 P Jump 0.00 Hz 0
227 Reserved 0 0
228 Reserved 0 0
229 Reserved 0 0
RSLogix 5000
Page 130 / 170
248 Enh Control Word 0000000000000000 0
250 Reserved 0 0
251 Reserved 0 0
252 Reserved 0 0
253 Reserved 0 0
254 Reserved 0 0
255 Reserved 0 0
256 Reserved 0 0
257 Reserved 0 0
258 Reserved 0 0
259 Reserved 0 0
260 Reserved 0 0
261 Reserved 0 0
262 Reserved 0 0
263 Reserved 0 0
264 Reserved 0 0
265 Reserved 0 0
266 Reserved 0 0
267 Reserved 0 0
268 Reserved 0 0
269 Reserved 0 0
270 Reserved 0 0
271 Reserved 0 0
272 Reserved 0 0
273 Reserved 0 0
274 Reserved 0 0
275 Reserved 0 0
276 Reserved 0 0
277 Reserved 0 0
278 Reserved 0 0
279 Reserved 0 0
280 Reserved 0 0
281 Reserved 0 0
282 Reserved 0 0
RSLogix 5000
Page 131 / 170
283 Reserved 0 0
284 Reserved 0 0
285 Reserved 0 0
286 Reserved 0 0
287 Reserved 0 0
288 Reserved 0 0
289 Reserved 0 0
290 Reserved 0 0
291 Reserved 0 0
292 Reserved 0 0
293 Reserved 0 0
294 Reserved 0 0
295 Reserved 0 0
296 Reserved 0 0
297 Reserved 0 0
298 Reserved 0 0
299 Reserved 0 0
300 Reserved 0 0
301 Drive Status 2 0000000000000000 0
302 Fiber Status 0000000000000000 0
RSLogix 5000
Page 132 / 170
Parameter List - PowerFlex 40P - VFD_Bumper Page 1
6 Drive Status 0000000000000010 2
7 Fault 1 Code 4 4
9 Fault 3 Code 4 4
13 Contrl In Status 0000000000000000 0
14 Dig In Status 0000000000000000 0
15 Comm Status 0000000000000101 5
17 Drive Type 0 0
19 Testpoint Data 0000000000000000 0
20 Analog In 0-10V 0.0 % 0
21 Analog In 4-20mA 0.0 % 0
24 Drive Temp 0 C 0
30 Reserved 0 0
42 Reserved 0 0
44 Reserved 0 0
45 Reserved 0 0
46 Reserved 0 0
47 Reserved 0 0
RSLogix 5000
Page 133 / 170
48 Reserved 0 0
49 Reserved 0 0
50 Reserved 0 0
83 S Curve % 0 % 0
RSLogix 5000
Page 134 / 170
102 Testpoint Sel 0000010000000000 1024
110 Anlg In 0-10V Lo 0.0 % 0
111 Anlg In 0-10V Hi 100.0 % 1000
112 Anlg In4-20mA Lo 0.0 % 0
113 Anlg In4-20mA Hi 100.0 % 1000
140 Stp Logic 0 0000000011110001 241
141 Stp Logic 1 0000000011110001 241
RSLogix 5000
Page 135 / 170
142 Stp Logic 2 0000000011110001 241
143 Stp Logic 3 0000000011110001 241
144 Stp Logic 4 0000000011110001 241
145 Stp Logic 5 0000000011110001 241
146 Stp Logic 6 0000000011110001 241
147 Stp Logic 7 0000000011110001 241
148 Reserved 0 0
149 Reserved 0 0
158 Reserved 0 0
159 Reserved 0 0
163 DB Threshold 100.0 % 1000
164 Reserved 0 0
165 Reserved 0 0
166 Reserved 0 0
167 Reserved 0 0
168 Reserved 0 0
169 Reserved 0 0
170 Reserved 0 0
171 Reserved 0 0
172 Reserved 0 0
173 Reserved 0 0
174 Reserved 0 0
175 Reserved 0 0
176 Reserved 0 0
177 Reserved 0 0
178 Reserved 0 0
179 Reserved 0 0
180 Reserved 0 0
181 Reserved 0 0
182 Reserved 0 0
183 Reserved 0 0
184 Reserved 0 0
185 Reserved 0 0
186 Reserved 0 0
187 Reserved 0 0
188 Reserved 0 0
RSLogix 5000
Page 136 / 170
189 Reserved 0 0
190 Reserved 0 0
191 Reserved 0 0
192 Reserved 0 0
193 Reserved 0 0
194 Reserved 0 0
195 Reserved 0 0
196 Reserved 0 0
197 Reserved 0 0
198 Reserved 0 0
199 Reserved 0 0
200 Reserved 0 0
213 P Jump 0.00 Hz 0
227 Reserved 0 0
228 Reserved 0 0
229 Reserved 0 0
RSLogix 5000
Page 137 / 170
248 Enh Control Word 0000000000000000 0
250 Reserved 0 0
251 Reserved 0 0
252 Reserved 0 0
253 Reserved 0 0
254 Reserved 0 0
255 Reserved 0 0
256 Reserved 0 0
257 Reserved 0 0
258 Reserved 0 0
259 Reserved 0 0
260 Reserved 0 0
261 Reserved 0 0
262 Reserved 0 0
263 Reserved 0 0
264 Reserved 0 0
265 Reserved 0 0
266 Reserved 0 0
267 Reserved 0 0
268 Reserved 0 0
269 Reserved 0 0
270 Reserved 0 0
271 Reserved 0 0
272 Reserved 0 0
273 Reserved 0 0
274 Reserved 0 0
275 Reserved 0 0
276 Reserved 0 0
277 Reserved 0 0
278 Reserved 0 0
279 Reserved 0 0
280 Reserved 0 0
281 Reserved 0 0
282 Reserved 0 0
RSLogix 5000
Page 138 / 170
283 Reserved 0 0
284 Reserved 0 0
285 Reserved 0 0
286 Reserved 0 0
287 Reserved 0 0
288 Reserved 0 0
289 Reserved 0 0
290 Reserved 0 0
291 Reserved 0 0
292 Reserved 0 0
293 Reserved 0 0
294 Reserved 0 0
295 Reserved 0 0
296 Reserved 0 0
297 Reserved 0 0
298 Reserved 0 0
299 Reserved 0 0
300 Reserved 0 0
301 Drive Status 2 0000000000000000 0
302 Fiber Status 0000000000000000 0
RSLogix 5000
Page 139 / 170
Parameter List - PowerFlex 40P - VFD_Standup Page 1
6 Drive Status 0000000000000010 2
7 Fault 1 Code 4 4
9 Fault 3 Code 4 4
13 Contrl In Status 0000000000000000 0
14 Dig In Status 0000000000000000 0
15 Comm Status 0000000000000100 4
17 Drive Type 0 0
19 Testpoint Data 0000000000000000 0
20 Analog In 0-10V 0.0 % 0
21 Analog In 4-20mA 0.0 % 0
24 Drive Temp 0 C 0
30 Reserved 0 0
42 Reserved 0 0
44 Reserved 0 0
45 Reserved 0 0
46 Reserved 0 0
47 Reserved 0 0
RSLogix 5000
Page 140 / 170
48 Reserved 0 0
49 Reserved 0 0
50 Reserved 0 0
83 S Curve % 0 % 0
RSLogix 5000
Page 141 / 170
102 Testpoint Sel 0000010000000000 1024
110 Anlg In 0-10V Lo 0.0 % 0
111 Anlg In 0-10V Hi 100.0 % 1000
112 Anlg In4-20mA Lo 0.0 % 0
113 Anlg In4-20mA Hi 100.0 % 1000
140 Stp Logic 0 0000000011110001 241
141 Stp Logic 1 0000000011110001 241
RSLogix 5000
Page 142 / 170
142 Stp Logic 2 0000000011110001 241
143 Stp Logic 3 0000000011110001 241
144 Stp Logic 4 0000000011110001 241
145 Stp Logic 5 0000000011110001 241
146 Stp Logic 6 0000000011110001 241
147 Stp Logic 7 0000000011110001 241
148 Reserved 0 0
149 Reserved 0 0
158 Reserved 0 0
159 Reserved 0 0
163 DB Threshold 100.0 % 1000
164 Reserved 0 0
165 Reserved 0 0
166 Reserved 0 0
167 Reserved 0 0
168 Reserved 0 0
169 Reserved 0 0
170 Reserved 0 0
171 Reserved 0 0
172 Reserved 0 0
173 Reserved 0 0
174 Reserved 0 0
175 Reserved 0 0
176 Reserved 0 0
177 Reserved 0 0
178 Reserved 0 0
179 Reserved 0 0
180 Reserved 0 0
181 Reserved 0 0
182 Reserved 0 0
183 Reserved 0 0
184 Reserved 0 0
185 Reserved 0 0
186 Reserved 0 0
187 Reserved 0 0
188 Reserved 0 0
RSLogix 5000
Page 143 / 170
189 Reserved 0 0
190 Reserved 0 0
191 Reserved 0 0
192 Reserved 0 0
193 Reserved 0 0
194 Reserved 0 0
195 Reserved 0 0
196 Reserved 0 0
197 Reserved 0 0
198 Reserved 0 0
199 Reserved 0 0
200 Reserved 0 0
213 P Jump 0.00 Hz 0
227 Reserved 0 0
228 Reserved 0 0
229 Reserved 0 0
RSLogix 5000
Page 144 / 170
248 Enh Control Word 0000000000000000 0
250 Reserved 0 0
251 Reserved 0 0
252 Reserved 0 0
253 Reserved 0 0
254 Reserved 0 0
255 Reserved 0 0
256 Reserved 0 0
257 Reserved 0 0
258 Reserved 0 0
259 Reserved 0 0
260 Reserved 0 0
261 Reserved 0 0
262 Reserved 0 0
263 Reserved 0 0
264 Reserved 0 0
265 Reserved 0 0
266 Reserved 0 0
267 Reserved 0 0
268 Reserved 0 0
269 Reserved 0 0
270 Reserved 0 0
271 Reserved 0 0
272 Reserved 0 0
273 Reserved 0 0
274 Reserved 0 0
275 Reserved 0 0
276 Reserved 0 0
277 Reserved 0 0
278 Reserved 0 0
279 Reserved 0 0
280 Reserved 0 0
281 Reserved 0 0
282 Reserved 0 0
RSLogix 5000
Page 145 / 170
283 Reserved 0 0
284 Reserved 0 0
285 Reserved 0 0
286 Reserved 0 0
287 Reserved 0 0
288 Reserved 0 0
289 Reserved 0 0
290 Reserved 0 0
291 Reserved 0 0
292 Reserved 0 0
293 Reserved 0 0
294 Reserved 0 0
295 Reserved 0 0
296 Reserved 0 0
297 Reserved 0 0
298 Reserved 0 0
299 Reserved 0 0
300 Reserved 0 0
301 Drive Status 2 0000000000000000 0
302 Fiber Status 0000000000000000 0
RSLogix 5000
Page 146 / 170
Parameter List - PowerFlex 40P - VFD_Power_Ramp Page 1
6 Drive Status 0000000000000010 2
7 Fault 1 Code 4 4
9 Fault 3 Code 4 4
13 Contrl In Status 0000000000000000 0
14 Dig In Status 0000000000000000 0
15 Comm Status 0000000000000101 5
17 Drive Type 0 0
19 Testpoint Data 0000000000000000 0
20 Analog In 0-10V 0.0 % 0
21 Analog In 4-20mA 0.0 % 0
24 Drive Temp 0 C 0
30 Reserved 0 0
42 Reserved 0 0
44 Reserved 0 0
45 Reserved 0 0
46 Reserved 0 0
47 Reserved 0 0
RSLogix 5000
Page 147 / 170
48 Reserved 0 0
49 Reserved 0 0
50 Reserved 0 0
83 S Curve % 0 % 0
RSLogix 5000
Page 148 / 170
102 Testpoint Sel 0000010000000000 1024
110 Anlg In 0-10V Lo 0.0 % 0
111 Anlg In 0-10V Hi 100.0 % 1000
112 Anlg In4-20mA Lo 0.0 % 0
113 Anlg In4-20mA Hi 100.0 % 1000
140 Stp Logic 0 0000000011110001 241
141 Stp Logic 1 0000000011110001 241
RSLogix 5000
Page 149 / 170
142 Stp Logic 2 0000000011110001 241
143 Stp Logic 3 0000000011110001 241
144 Stp Logic 4 0000000011110001 241
145 Stp Logic 5 0000000011110001 241
146 Stp Logic 6 0000000011110001 241
147 Stp Logic 7 0000000011110001 241
148 Reserved 0 0
149 Reserved 0 0
158 Reserved 0 0
159 Reserved 0 0
163 DB Threshold 100.0 % 1000
164 Reserved 0 0
165 Reserved 0 0
166 Reserved 0 0
167 Reserved 0 0
168 Reserved 0 0
169 Reserved 0 0
170 Reserved 0 0
171 Reserved 0 0
172 Reserved 0 0
173 Reserved 0 0
174 Reserved 0 0
175 Reserved 0 0
176 Reserved 0 0
177 Reserved 0 0
178 Reserved 0 0
179 Reserved 0 0
180 Reserved 0 0
181 Reserved 0 0
182 Reserved 0 0
183 Reserved 0 0
184 Reserved 0 0
185 Reserved 0 0
186 Reserved 0 0
187 Reserved 0 0
188 Reserved 0 0
RSLogix 5000
Page 150 / 170
189 Reserved 0 0
190 Reserved 0 0
191 Reserved 0 0
192 Reserved 0 0
193 Reserved 0 0
194 Reserved 0 0
195 Reserved 0 0
196 Reserved 0 0
197 Reserved 0 0
198 Reserved 0 0
199 Reserved 0 0
200 Reserved 0 0
213 P Jump 0.00 Hz 0
227 Reserved 0 0
228 Reserved 0 0
229 Reserved 0 0
RSLogix 5000
Page 151 / 170
248 Enh Control Word 0000000000000000 0
250 Reserved 0 0
251 Reserved 0 0
252 Reserved 0 0
253 Reserved 0 0
254 Reserved 0 0
255 Reserved 0 0
256 Reserved 0 0
257 Reserved 0 0
258 Reserved 0 0
259 Reserved 0 0
260 Reserved 0 0
261 Reserved 0 0
262 Reserved 0 0
263 Reserved 0 0
264 Reserved 0 0
265 Reserved 0 0
266 Reserved 0 0
267 Reserved 0 0
268 Reserved 0 0
269 Reserved 0 0
270 Reserved 0 0
271 Reserved 0 0
272 Reserved 0 0
273 Reserved 0 0
274 Reserved 0 0
275 Reserved 0 0
276 Reserved 0 0
277 Reserved 0 0
278 Reserved 0 0
279 Reserved 0 0
280 Reserved 0 0
281 Reserved 0 0
282 Reserved 0 0
RSLogix 5000
Page 152 / 170
283 Reserved 0 0
284 Reserved 0 0
285 Reserved 0 0
286 Reserved 0 0
287 Reserved 0 0
288 Reserved 0 0
289 Reserved 0 0
290 Reserved 0 0
291 Reserved 0 0
292 Reserved 0 0
293 Reserved 0 0
294 Reserved 0 0
295 Reserved 0 0
296 Reserved 0 0
297 Reserved 0 0
298 Reserved 0 0
299 Reserved 0 0
300 Reserved 0 0
301 Drive Status 2 0000000000000000 0
302 Fiber Status 0000000000000000 0
RSLogix 5000
Page 153 / 170
Parameter List - PowerFlex 40P - VFD_Infeed_Belts Page 1
6 Drive Status 0000000000000010 2
7 Fault 1 Code 4 4
9 Fault 3 Code 4 4
13 Contrl In Status 0000000000000000 0
14 Dig In Status 0000000000000000 0
15 Comm Status 0000000000000101 5
17 Drive Type 0 0
19 Testpoint Data 0000000000000000 0
20 Analog In 0-10V 0.0 % 0
21 Analog In 4-20mA 0.0 % 0
24 Drive Temp 0 C 0
30 Reserved 0 0
42 Reserved 0 0
44 Reserved 0 0
45 Reserved 0 0
46 Reserved 0 0
47 Reserved 0 0
RSLogix 5000
Page 154 / 170
48 Reserved 0 0
49 Reserved 0 0
50 Reserved 0 0
83 S Curve % 0 % 0
RSLogix 5000
Page 155 / 170
102 Testpoint Sel 0000010000000000 1024
110 Anlg In 0-10V Lo 0.0 % 0
111 Anlg In 0-10V Hi 100.0 % 1000
112 Anlg In4-20mA Lo 0.0 % 0
113 Anlg In4-20mA Hi 100.0 % 1000
140 Stp Logic 0 0000000011110001 241
141 Stp Logic 1 0000000011110001 241
RSLogix 5000
Page 156 / 170
142 Stp Logic 2 0000000011110001 241
143 Stp Logic 3 0000000011110001 241
144 Stp Logic 4 0000000011110001 241
145 Stp Logic 5 0000000011110001 241
146 Stp Logic 6 0000000011110001 241
147 Stp Logic 7 0000000011110001 241
148 Reserved 0 0
149 Reserved 0 0
158 Reserved 0 0
159 Reserved 0 0
163 DB Threshold 100.0 % 1000
164 Reserved 0 0
165 Reserved 0 0
166 Reserved 0 0
167 Reserved 0 0
168 Reserved 0 0
169 Reserved 0 0
170 Reserved 0 0
171 Reserved 0 0
172 Reserved 0 0
173 Reserved 0 0
174 Reserved 0 0
175 Reserved 0 0
176 Reserved 0 0
177 Reserved 0 0
178 Reserved 0 0
179 Reserved 0 0
180 Reserved 0 0
181 Reserved 0 0
182 Reserved 0 0
183 Reserved 0 0
184 Reserved 0 0
185 Reserved 0 0
186 Reserved 0 0
187 Reserved 0 0
188 Reserved 0 0
RSLogix 5000
Page 157 / 170
189 Reserved 0 0
190 Reserved 0 0
191 Reserved 0 0
192 Reserved 0 0
193 Reserved 0 0
194 Reserved 0 0
195 Reserved 0 0
196 Reserved 0 0
197 Reserved 0 0
198 Reserved 0 0
199 Reserved 0 0
200 Reserved 0 0
213 P Jump 0.00 Hz 0
227 Reserved 0 0
228 Reserved 0 0
229 Reserved 0 0
RSLogix 5000
Page 158 / 170
248 Enh Control Word 0000000000000000 0
250 Reserved 0 0
251 Reserved 0 0
252 Reserved 0 0
253 Reserved 0 0
254 Reserved 0 0
255 Reserved 0 0
256 Reserved 0 0
257 Reserved 0 0
258 Reserved 0 0
259 Reserved 0 0
260 Reserved 0 0
261 Reserved 0 0
262 Reserved 0 0
263 Reserved 0 0
264 Reserved 0 0
265 Reserved 0 0
266 Reserved 0 0
267 Reserved 0 0
268 Reserved 0 0
269 Reserved 0 0
270 Reserved 0 0
271 Reserved 0 0
272 Reserved 0 0
273 Reserved 0 0
274 Reserved 0 0
275 Reserved 0 0
276 Reserved 0 0
277 Reserved 0 0
278 Reserved 0 0
279 Reserved 0 0
280 Reserved 0 0
281 Reserved 0 0
282 Reserved 0 0
RSLogix 5000
Page 159 / 170
283 Reserved 0 0
284 Reserved 0 0
285 Reserved 0 0
286 Reserved 0 0
287 Reserved 0 0
288 Reserved 0 0
289 Reserved 0 0
290 Reserved 0 0
291 Reserved 0 0
292 Reserved 0 0
293 Reserved 0 0
294 Reserved 0 0
295 Reserved 0 0
296 Reserved 0 0
297 Reserved 0 0
298 Reserved 0 0
299 Reserved 0 0
300 Reserved 0 0
301 Drive Status 2 0000000000000000 0
302 Fiber Status 0000000000000000 0
RSLogix 5000
Page 160 / 170
Parameter List - PowerFlex 40P - VFD_BAO Page 1
Al l Par amet er s 9/ 29/ 2013 10: 20: 12 AM
C: \ USERS\ USER1\ DESKTOP\ PACE_3909_COLGATE_COMPLETE_ENGLI SH_SPANI SH\ Pace_3909. ACD
1 Out put Fr eq 0. 00 Hz 0
2 Commanded Fr eq 20. 00 Hz 2000
3 Out put Cur r ent 0. 00 A 0
4 Out put Vol t age 0. 0 V 0
5 DC Bus Vol t age 657 V 657
6 Dr i ve St at us 0000000000000010 2
7 Faul t 1 Code 4 4
8 Faul t 2 Code 111 111
9 Faul t 3 Code 4 4
10 Pr ocess Di spl ay 0 0
11 Pr ocess Fr act 0. 00 0
12 Cont r ol Sour ce 52 52
13 Cont r l I n St at us 0000000000000100 4
14 Di g I n St at us 0000000000000000 0
15 CommSt at us 0000000000000101 5
16 Cont r ol SWVer 2. 01 201
17 Dr i ve Type 5504 5504
18 El apsed Run Ti me 0 x10h 0
19 Test poi nt Dat a 0010001111001110 9166
20 Anal og I n 0- 10V 0. 0 % 0
21 Anal og I n 4- 20mA 0. 0 % 0
22 Out put Power 0. 00 kW 0
23 Out put Powr Fct r 0. 0 deg 0
24 Dr i ve Temp 27 C 27
25 Count er St at us 0 0
26 Ti mer St at us 0 Sec 0
27 Ti mer St at Fr act 0. 0 0
28 St p Logi c St at us 0 0
29 Tor que Cur r ent 0. 00 A 0
30 Reser ved 0 0
31 Mot or NP Vol t s 460 V 460
32 Mot or NP Her t z 60 Hz 60
RSLogi x 5000
Page 161 / 170
33 Mot or OL Cur r ent 2. 3 A 23
34 Mi ni mumFr eq 0. 00 Hz 0
35 Maxi mumFr eq 60. 00 Hz 6000
36 St ar t Sour ce CommPor t 5
37 St op Mode Ramp, CF 0
38 Speed Ref er ence CommPor t 5
39 Accel Ti me 1 2. 0 Sec 20
40 Decel Ti me 1 3. 0 Sec 30
41 Reset To Def al t s Ready/ I dl e 0
42 Reser ved 0 0
43 Mot or OL Ret Di sabl ed 0
44 Reser ved 0 0
45 Reser ved 0 0
46 Reser ved 0 0
47 Reser ved 0 0
48 Reser ved 0 0
49 Reser ved 0 0
50 Reser ved 0 0
51 Di gi t al I n1 Sel Pr eset Fr eq 4
52 Di gi t al I n2 Sel Pr eset Fr eq 4
53 Di gi t al I n3 Sel Cl ear Faul t 7
54 Di gi t al I n4 Sel J og For war d 11
55 Rel ay Out Sel Ready/ Faul t 0
56 Rel ay Out Level 0 0
57 Rel ay Out Level F 0. 0 0
58 Opt o Out 1 Sel Mot or Runni ng 2
59 Opt o Out 1 Level 0 0
60 Opt o Out 1 Level F 0. 0 0
61 Opt o Out 2 Sel At Fr equency 1
62 Opt o Out 2 Level 0 0
63 Opt o Out 2 Level F 0. 0 0
64 Opt o Out Logi c 1=NO / 2=NO 0
RSLogi x 5000
Page 162 / 170
65 Anal og Out Sel Out Fr eq 0- 10 0
66 Anal og Out Hi gh 100 % 100
69 I nt er nal Fr eq 60. 00 Hz 6000
70 Pr eset Fr eq 0 0. 00 Hz 0
71 Pr eset Fr eq 1 5. 00 Hz 500
72 Pr eset Fr eq 2 10. 00 Hz 1000
73 Pr eset Fr eq 3 20. 00 Hz 2000
74 Pr eset Fr eq 4 30. 00 Hz 3000
75 Pr eset Fr eq 5 40. 00 Hz 4000
76 Pr eset Fr eq 6 50. 00 Hz 5000
77 Pr eset Fr eq 7 60. 00 Hz 6000
78 J og Fr equency 10. 00 Hz 1000
79 J og Accel / Decel 10. 0 Sec 100
80 DC Br ake Ti me 0. 0 Sec 0
81 DC Br ake Level 0. 1 A 1
82 DB Resi st or Sel Di sabl ed % 0
83 S Cur ve % 0 % 0
84 Boost Sel ect 5. 0, CT 8
85 St ar t Boost 2. 5 % 25
86 Br eak Vol t age 25. 0 % 250
87 Br eak Fr equency 15. 0 Hz 150
88 Maxi mumVol t age 460 V 460
89 Cur r ent Li mi t 1 3. 5 A 35
90 Mot or OL Sel ect No Der at e 0
91 PWM Fr equency 4. 0 kHz 40
92 Aut o Rst r t Tr i es 0 0
93 Aut o Rst r t Del ay 1. 0 Sec 10
94 St ar t At Power Up Di sabl ed 0
95 Rever se Di sabl e REV Enabl ed 0
96 Fl yi ng St ar t En Di sabl ed 0
RSLogi x 5000
Page 163 / 170
97 Compensat i on El ect r i cal 1
98 SWCur r ent Tr i p 0. 0 A 0
99 Pr ocess Fact or 30. 0 300
100 Faul t Cl ear Ready/ I dl e 0
101 Pr ogr amLock 0 0
102 Test poi nt Sel 0000010000000000 1024
103 CommDat a Rat e 9600 3
104 CommNode Addr 100 100
105 CommLoss Act i on Faul t 0
106 CommLoss Ti me 5. 0 Sec 50
107 CommFor mat RTU 8- N- 1 0
108 Language Engl i sh 1
109 Anl g Out Set pt 0. 0 % 0
110 Anl g I n 0- 10V Lo 0. 0 % 0
111 Anl g I n 0- 10V Hi 100. 0 % 1000
112 Anl g I n4- 20mA Lo 0. 0 % 0
113 Anl g I n4- 20mA Hi 100. 0 % 1000
114 Sl i p Her t z @FLA 0. 0 Hz 0
115 Pr ocess Ti me Lo 0. 00 0
116 Pr ocess Ti me Hi 0. 00 0
117 Bus Reg Mode Enabl ed 1
118 Cur r ent Li mi t 2 3. 5 A 35
119 Ski p Fr equency 0 Hz 0
120 Ski p Fr eq Band 0. 0 Hz 0
121 St al l Faul t Ti me 60 Seconds 0
122 Anal og I n Loss Di sabl ed 0
123 10V Bi pol ar Enbl Uni - Pol ar I n 0
124 Var PWM Di sabl e Enabl ed 0
125 Tor que Per f Mode Sensr l s Vect 1
126 Mot or NP FLA 1. 5 A 15
127 Aut ot une Ready/ I dl e 0
128 I R Vol t age Dr op 13. 0 Vac 130
RSLogi x 5000
Page 164 / 170
129 Fl ux Cur r ent Ref 0. 75 A 75
130 PI D Tr i mHi 60. 0 Hz 600
131 PI D Tr i mLo 0. 0 Hz 0
132 PI D Ref Sel PI D Di sabl ed 0
133 PI D Feedback Sel 0- 10V I nput 0
134 PI D Pr op Gai n 0. 01 1
135 PI D I nt eg Ti me 2. 0 Sec 20
136 PI D Di f f Rat e 0. 00 1/ s 0
137 PI D Set poi nt 0. 0 % 0
138 PI D Deadband 0. 0 % 0
139 PI D Pr el oad 0. 0 Hz 0
140 St p Logi c 0 0000000011110001 241
141 St p Logi c 1 0000000011110001 241
142 St p Logi c 2 0000000011110001 241
143 St p Logi c 3 0000000011110001 241
144 St p Logi c 4 0000000011110001 241
145 St p Logi c 5 0000000011110001 241
146 St p Logi c 6 0000000011110001 241
147 St p Logi c 7 0000000011110001 241
148 Reser ved 0 0
149 Reser ved 0 0
150 St p Logi c Ti me 0 30. 0 Sec 300
158 Reser ved 0 0
159 Reser ved 0 0
160 EM Br k Of f Del ay 2. 00 Sec 200
RSLogi x 5000
Page 165 / 170
161 EM Br k On Del ay 2. 00 Sec 200
163 DB Thr eshol d 100. 0 % 1000
164 Reser ved 0 0
165 Reser ved 0 0
166 Reser ved 0 0
167 Reser ved 0 0
168 Reser ved 0 0
169 Reser ved 0 0
170 Reser ved 0 0
171 Reser ved 0 0
172 Reser ved 0 0
173 Reser ved 0 0
174 Reser ved 0 0
175 Reser ved 0 0
176 Reser ved 0 0
177 Reser ved 0 0
178 Reser ved 0 0
179 Reser ved 0 0
180 Reser ved 0 0
181 Reser ved 0 0
182 Reser ved 0 0
183 Reser ved 0 0
184 Reser ved 0 0
185 Reser ved 0 0
186 Reser ved 0 0
187 Reser ved 0 0
188 Reser ved 0 0
189 Reser ved 0 0
190 Reser ved 0 0
191 Reser ved 0 0
192 Reser ved 0 0
RSLogi x 5000
Page 166 / 170
193 Reser ved 0 0
194 Reser ved 0 0
195 Reser ved 0 0
196 Reser ved 0 0
197 Reser ved 0 0
198 Reser ved 0 0
199 Reser ved 8000 8000
200 Reser ved 0 0
201 LED Di spl ay Opt 1- 7, 10 Onl y 2
202 Di gi t al Ter m3 St ar t Sour ce 0
205 Accel Ti me 4 30. 0 Sec 300
206 Decel Ti me 4 30. 0 Sec 300
207 CommWr i t e Mode Save 0
209 Hal f Bus Enabl e Di sabl ed 0
210 Max Tr aver se 0. 00 Hz 0
211 Tr aver se I nc 0. 00 Sec 0
212 Tr aver se Dec 0. 00 Sec 0
213 P J ump 0. 00 Hz 0
214 Sync Ti me 0. 0 Sec 0
215 Speed Rat i o 1. 00 100
216 Mot or Fdbk Type None 0
217 Mot or NP Pol es 4 4
219 Pul se I n Scal e 64 64
220 Ki Speed Loop 2. 0 20
221 Kp Speed Loop 0. 5 5
222 Posi t i oni ng Mode Ti me St eps 0
223 Fi nd Home Fr eq 10. 0 Hz 100
224 Fi nd Home Di r For war d 0
RSLogi x 5000
Page 167 / 170
226 Count s Per Uni t 4096 4096
227 Reser ved 0 0
228 Reser ved 0 0
229 Reser ved 0 0
230 St ep Uni t s 0 0 0
231 St ep Uni t s F 0 0. 00 0
232 St ep Uni t s 1 0 0
233 St ep Uni t s F 1 0. 00 0
234 St ep Uni t s 2 0 0
235 St ep Uni t s F 2 0. 00 0
236 St ep Uni t s 3 0 0
237 St ep Uni t s F 3 0. 00 0
238 St ep Uni t s 4 0 0
239 St ep Uni t s F 4 0. 00 0
240 St ep Uni t s 5 0 0
241 St ep Uni t s F 5 0. 00 0
242 St ep Uni t s 6 0 0
243 St ep Uni t s F 6 0. 00 0
244 St ep Uni t s 7 0 0
245 St ep Uni t s F 7 0. 00 0
246 Pos Reg Fi l t er 8 8
247 Pos Reg Gai n 3. 0 30
248 Enh Cont r ol Wor d 0000000000000000 0
249 Cmd St at Sel ect Vel oci t y 0
250 Reser ved 0 0
251 Reser ved 0 0
252 Reser ved 0 0
253 Reser ved 0 0
254 Reser ved 0 0
255 Reser ved 0 0
256 Reser ved 0 0
RSLogi x 5000
Page 168 / 170
257 Reser ved 0 0
258 Reser ved 0 0
259 Reser ved 0 0
260 Reser ved 0 0
261 Reser ved 0 0
262 Reser ved 0 0
263 Reser ved 0 0
264 Reser ved 0 0
265 Reser ved 0 0
266 Reser ved 0 0
267 Reser ved 0 0
268 Reser ved 0 0
269 Reser ved 0 0
270 Reser ved 0 0
271 Reser ved 0 0
272 Reser ved 0 0
273 Reser ved 0 0
274 Reser ved 0 0
275 Reser ved 0 0
276 Reser ved 0 0
277 Reser ved 0 0
278 Reser ved 0 0
279 Reser ved 0 0
280 Reser ved 0 0
281 Reser ved 0 0
282 Reser ved 0 0
283 Reser ved 0 0
284 Reser ved 0 0
285 Reser ved 0 0
286 Reser ved 0 0
287 Reser ved 0 0
288 Reser ved 0 0
RSLogi x 5000
Page 169 / 170
289 Reser ved 0 0
290 Reser ved 0 0
291 Reser ved 0 0
292 Reser ved 0 0
293 Reser ved 0 0
294 Reser ved 0 0
295 Reser ved 0 0
296 Reser ved 0 0
297 Reser ved 0 0
298 Reser ved 0 0
299 Reser ved 0 0
300 Reser ved 0 0
301 Dr i ve St at us 2 0000000000000001 1
302 Fi ber St at us 0000000000000000 0
303 Sl i p Hz Met er 0. 0 Hz 0
305 Speed Feedback F 0. 0 RPM 0
307 Encoder Speed F 0. 0 RPM 0
308 Uni t s Tr avel ed H 0 0
309 Uni t s Tr avel ed L 0. 00 0
RSLogi x 5000
Page 170 / 170

Complete 3909&3910

Uploaded by

Copyright:

Available Formats

Complete 3909&3910

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Complete 3909&3910

Uploaded by

Copyright:

Available Formats

MACHINE SERIAL NO.

3909,3910 & 3911

You might also like