Pioneer Deh-3050ub 4000ub Crt4052 SM
Pioneer Deh-3050ub 4000ub Crt4052 SM
Pioneer Deh-3050ub 4000ub Crt4052 SM
CRT4052
DEH-4000UB/XS/EW5
CD RDS RECEIVER
DEH-4000UB
CD RECEIVER
/XS/EW5
DEH-3050UB/XS/ES DEH-3050UB/XU/CN5
This service manual should be used together with the following manual(s):
Model No.
CX-3240
Order No.
CRT4050
Mech.Module
S10.5COMP2-iPod/USB
Remarks
CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
PIONEER CORPORATION
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
SAFETY INFORMATION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
- Safety Precautions for those who Service this Unit. When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable results.
B
Caution: 1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept. 2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1 but the laser component is capable of emitting radiation exceeding the limit for CLASS 1. A specially instructed person should do servicing operation of the apparatus.
E
Transistors Q101 in PCB drive the laser diodes. When Q101 is shorted between their terminals, the laser diodes will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam.
DEH-4000UB/XS/EW5
1 2 3 4
CAUTION
Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacture. Discord used batteries according to the manufacture's instructions.
A
DEH-4000UB/XS/EW5
5 6 7 8
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual. 1 Use specified parts for repair. Use genuine parts. Be sure to use important parts for safety. 2 Do not perform modifications without proper instructions. Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed. When you solder while repairing, please be sure that there are no cold solder and other debris. Soldering should be finished with the proper quantity. (Refer to the example) 4 Make sure the screws are tightly fastened. Please be sure that all screws are fastened, and that there are no loose screws. 5 Make sure each connectors are correctly inserted. Please be sure that all connectors are inserted, and that there are no imperfect insertion. 6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs. In addition, be sure that there are no pinched wires, etc. 7 Make sure screws and soldering scraps do not remain inside the product. Please check that neither solder debris nor screws remain inside the product. 8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord. Damaged power cords may lead to fire accidents, so please be sure that there are no damages. If you find a damaged power cord, please exchange it with a suitable one. 9 There should be no spark traces or similar marks on the power plug. When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure connections and suitable usage. Please exchange the power cord if necessary.
a Safe environment should be secured during servicing. When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries. Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification. Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper cleaning should be performed to restore their performances.
DEH-4000UB/XS/EW5
1 2 3 4
CONTENTS
SAFETY INFORMATION .....................................................................................................................................2 1. SERVICE PRECAUTIONS................................................................................................................................6 1.1 SERVICE PRECAUTIONS .........................................................................................................................6 1.2 NOTES ON SOLDERING...........................................................................................................................6 2. SPECIFICATIONS.............................................................................................................................................7 2.1 SPECIFICATIONS ......................................................................................................................................7 2.2 DISC/CONTENT FORMAT.........................................................................................................................9 2.3 PANEL FACILITIES ..................................................................................................................................10 2.4 CONNECTION DIAGRAM........................................................................................................................13 3. BASIC ITEMS FOR SERVICE ........................................................................................................................15 3.1 CHECK POINTS AFTER SERVICING .....................................................................................................15 3.2 PCB LOCATIONS.....................................................................................................................................15 3.3 JIGS LIST .................................................................................................................................................16 3.4 CLEANING ...............................................................................................................................................16 4. BLOCK DIAGRAM ..........................................................................................................................................18 4.1 BLOCK DIAGRAM....................................................................................................................................18 5. DIAGNOSIS ....................................................................................................................................................23 5.1 OPERATIONAL FLOWCHART.................................................................................................................23 5.2 ERROR CODE LIST.................................................................................................................................24 5.3 CONNECTOR FUNCTION DESCRIPTION .............................................................................................26 6. SERVICE MODE.............................................................................................................................................27 6.1 CD TEST MODE.......................................................................................................................................27 7. DISASSEMBLY ...............................................................................................................................................30 8. EACH SETTING AND ADJUSTMENT............................................................................................................35 8.1 PCL OUTPUT CONFIRMATION ..............................................................................................................35 8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT ....................................................36 9. EXPLODED VIEWS AND PARTS LIST ..........................................................................................................38 9.1 PACKING..................................................................................................................................................38 9.2 EXTERIOR(1) ...........................................................................................................................................40 9.3 EXTERIOR(2) ...........................................................................................................................................42 9.4 CD MECHANISM MODULE .....................................................................................................................44 10. SCHEMATIC DIAGRAM................................................................................................................................46 10.1 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)............................................................................46 10.2 KEYBOARD UNIT ..................................................................................................................................52 10.3 CD MECHANISM MODULE(GUIDE PAGE)...........................................................................................54 10.4 WAVEFORMS.........................................................................................................................................60 11. PCB CONNECTION DIAGRAM ....................................................................................................................64 11.1 TUNER AMP UNIT .................................................................................................................................64 11.2 KEYBOARD UNIT...................................................................................................................................68 11.3 CD CORE UNIT(S10.5COMP2-USB).....................................................................................................70 12. ELECTRICAL PARTS LIST...........................................................................................................................72
A
DEH-4000UB/XS/EW5
5 6 7 8
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A
- Service Precaution
1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. 2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit. 3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment (shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing the pickup unit, be sure to check the grating. 5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction. 6. The sheet (Mechanism cover) can not be reused if you removed it.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C. Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of the soldering iron. Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia.
DEH-4000UB/XS/EW5
1 2 3 4
2. SPECIFICATIONS
2.1 SPECIFICATIONS
- EW5 Model
A
DEH-4000UB/XS/EW5
5 6 7 8
- ES Model
A
DEH-4000UB/XS/EW5
1 2 3 4
- CN5 Model
A
DEH-4000UB/XS/EW5
5 6 7 8
10
DEH-4000UB/XS/EW5
1 2 3 4
DEH-4000UB/XS/EW5
5 6 7 8
11
12
DEH-4000UB/XS/EW5
1 2 3 4
DEH-4000UB/XS/EW5
5 6 7 8
13
14
DEH-4000UB/XS/EW5
1 2 3 4
2 CD 3 FM/AM tuner
4 5
The media used for the operating check must be ejected. No scratches or dirt on its appearance after receiving it for service.
C CD Core Unit
(S10.5COMP2-USB)
Unit Number Unit Number Unit Number Unit Name Unit Number Unit Number Unit Name Unit Number Unit Name Unit Number Unit Name
: : : : : : : : : : :
YWM5203(EW5) YWM5205(ES) YWM5207(CN5) Tuner Amp Unit (EW5) (ES) Keyboard Unit (CN5) Keyboard Unit CWX3527 CD Core Unit (S10.5COMP2-USB)
B Keyboard Unit
F
DEH-4000UB/XS/EW5
5 6 7 8
15
- Grease List
B
3.4 CLEANING
- Jigs List
Name Jig No. TCD-782 Test Disc Before shipping out the product, be sure to clean the L.P.F. following portions by using the prescribed cleaning tools: Portions to be cleaned CD pickup lenses Cleaning tools Cleaning liquid : GEM1004 Cleaning paper : GED-008 Remarks Checking the grating Checking the grating (Two pieces)
- Grease List
Name Grease Grease
D
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
E
16
DEH-4000UB/XS/EW5
1 2 3 4
DEH-4000UB/XS/EW5
5 6 7 8
17
4. BLOCK DIAGRAM
4.1 BLOCK DIAGRAM
A
7
NC
6
CE2
13
ROM_VDD
5
SL
10 9
CK DI
8
CE1
11
LDET
TUNPDO
14
DO
TUNPDI
TUNPCK
LDET
CE2
SL
18
RDS_CK
19
RDS_DATA
20
RDS_LOCK
21
RDS_HSLK
IC5 5V 3.3V
B
OSC LPF
ANTENNA
CN401
1 2,3
1
AM ANT ATT
FMRF
23
T51
CF52
A
VD
AUDIOGND
C
OSCGND RFGND DGND
VDD_3.3
VCC
NC
12
15
22
16
17
VST,VCK
40
C CD CORE UNIT(S10.5COMP2-USB)
PICKUP UNIT (P10.5)(SERVICE)
LASER DIODE
SYSPW
48
CN101
LDMD 15 5 15 5 Q101
VDD2
RF-AMP, CD DECODER, MP3/WMA DECODER, DIGITAL SERVO / DATA PROCESSOR CPU, USB HOST CONTROLLER
141 142 LD PD REFOUT /USBXTAL 2 USBXTAL 1 X205 48MHz B.UP 28
SYNC
REFO 8 AC,BD,E,F
133
SW F INV
Q102 VCC
VDD2
24 USBCTL 25 FLG
/PUEN
39
E
CN701 CN701
16 17 13 DP DM LOUT
TD,FD SD,MD
IC201 PE5611B
DP DM
5 4 55
DP
D
B. UP 51
ILM
Q841
3 DM 7
LOUT
CDL
ILMPW
SPINDLE MOTOR
M
16 22 SOP LOEJ 15 SOM 21 18 LCOP CLCONT 17 9 CONT LCOM 28 20 41 LOEJ CLCONT CONT /RESET
VDD2 VDD
CD 3.3V REGULATOR
VDD
9
Q842 ROT0
VDD
11
CDVDD
IC702 NJM2885DL1-33
4 3
ROT1
16
/RESET
12
CDRST
23 BRST,BRXEN,BSRQ,BDATA,BSCK Q702
CDRST
JOYST
82
BRST,BRXEN,BSRQ
8 7 10 9 S904 12EJ S905 8EJ S901 HOME 12EJ 8EJ DSCSNS HOME XTAL 50 /XTAL 52 X201 16.93MHz VD S903 DSCSNS 11
BDATA,BSCK
VD VD 2 1
18 19
VD
VD 7.5V REGULATOR
B.UP Q701 SWVDD 49
VDD
F
VDSENS
22
VDCONT
35 36 19
18
DEH-4000UB/XS/EW5
1 2 3 4
SWL
MUTE
Q351
CN351
SWL
5
RCA OUT
RCFL
6
FL
BZ601 BUZZER Q353
65 66 68 69 67
74
B,C
X601 15MHz VDD
Q912
XIN XOUT
15
B
VDD REGULATOR
Q911
13
SL
97
SL
Q401
RDS_CK RDS_HSLK
73 78
RCK RDS57K
DALMON
47
Lch
23
BSENS
Q402
RDS_DATA
B.UP
CN901
B.UP
BSENS 77 76
RDSDT
18
Q931
16 14
16 14
BACK UP
ASENS
RDS_LOCK
75
ACC
RDSLK
ACC
A
VDD 2
A
BUP
C
15 15
GND
POWER AMP
IN2_L IN1_L Pre/SW_L Front_L 12 10 11 14 12 FLIN RLIN MUTE 22 STBY 4
6,20 VCC
FLFL+ RLRL+
23 21 3 5
FLFL+ RLRL+
7 5 8 6 11
7 5 8 6 11
IC 301 PAL007C
B.REM 25
FL FL+ RL RL+
B.REM
AUXL AUXGND
2 1
IC151 PML018A
IN5+_L IN5-_L
Rear_L
MUTE
Q453
VST,VCK,VDT
B.UP
VDD3.3V
IC401 NJM2885DL1-33
VCC
MUTE
40
D
VCC8.4V REGULATOR
VCC
RR RR
+
B.UP
BACK UP B. REM
IC921 NJM2388F84
4
FR FR
+
FL
FL
+ +
YSPW
48
GND ACC
RL RL
B KEYBOARD UNIT
IC251 R5523N001B
4 VIN VOUT 5
CN803
US5V DM DP
CN1801
11 13 12 11 13 12 US5V USDM USDP
1 7
CN1802
1 2 3
VIN EN
SYNC
2 SW 5 FB 6 INV
USB
BCTL 25 FLG
24
1 3
EN FLG
D
ILM
Q841 B. UP 51
E
ILM+ 10 10 ILM+
ILLUMI
KEY MATRIX
ROTARY COMMANDER
S1801 EJECT S1805 REGION1 S1808 REGION2 S1802 SOURSE S1806 DISP/BACK S1809 RPT S1810 S Rtrv S1803 LIST S1804 BAND/ESC S1807 RDM (RED) (GREEN)
MPW
S1827
A,B
OYST
82
JOYST
JOYST
KST1-4 KDT1-3
SWVDD
VDD Q851 WVDD 49 Q852
OPT IN
SWVDD
SWVDD
47
VDD V3 REM
X0
54 55 X1801 5MHz
B,C
DPDT KYDT SENS 35 36 19 DPDT KYDT 5 6 5 6 14 DPDT KYDT DSENS
IC1802 GP1UX51RK
3 1
46 57
50 49
SI SO
X1
F
LCD LCD1801
DSENS 14
DEH-4000UB/XS/EW5
5 6 7 8
19
13
ROM_VDD
5
SL
10 9 8
CE1 CK DI
11
LDET
14
DO
18 19 20 21
RDS_LOCK RDS_CK RDS_DATA RDS_HSLK
IC 5 5V t 3.3V
LPF
AM ANT 1 ATT
24
23
B
ANT adj
T51
CF52
AUDIOGND
OSCGND
VDD_3.3
RFGND
DGND
3.3V
12
15
22
16
VCC 4
NC
17
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
RFGND FMANT VCC SL CE2 NC CE1 CK DI LDET OSCGND ROM_VDD DO DGND NC VDD_3.3 RDS_CK RDS_DATA RDS_LOCK
I O I I I I O
RF ground FM antenna input power supply signal level chip enable-2 non connection chip enable-1 clock data in lock detector osc ground power supply data out digital ground non connection power supply RDS clock RDS data RDS lock RDS high speed lock audio ground L channel output R channel output
O O O O
21 RDS_HSLK
22 AUDIOGND 23 L ch O 24 R ch O
AM antenna input high impedance AMANT pin is connected with an all antenna by way of 4.7 H. (LAU type inductor) A series circuit including an inductor and a resistor is connected with RF ground for the countermeasure against the hum of power transmission line. Ground of antenna block Input of FM antenna 75 ohm Surge absorber(DSP-201M-S00B)is necessary. The power supply for analog block. D.C 8.4 V 0.3 V Output of FM/AM signals level Chip enable for EEPROM Low active Not used Chip enable for AFRF High active Clock Data input Low active Ground of oscillator block Power supply for EEPROM pin 13 is connected with a power supply of micro computer. Data output Ground of digital block Not used The power supply for digital block. 3.3 V 0.2 V Output of RDS clock(2.5 V) Output of RDS data(2.5 V) Output unit High active(2.5 V) (RDS_LOCK turns over by the external transistor . Low active) Output unit High active(2.5 V)(RDS_HSLK turns over by the external transistor. Low active) Ground of audio block FM stereo L-ch signal output or AM audio output FM stereo R-ch signal output or AM audio output
20
DEH-4000UB/XS/EW5
1 2 3 4
13
ROM_VDD
5
SL
10 9 8
CE1 CK DI
11
NC
14
DO
18 19 20 21
NC NC NC NC
IC 5 5 V 3.3 V
LPF
AM ANT 1 AT T
24
IC 1 3.3 V MIXER, IF AM P
23
T51
CF52
AUDIOGND
OSCGND
VDD_3.3
RFGND
DGND
3.3 V
2.5 V
12
15
22
16
VCC 4
NC
17
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
RFGND FMANT VCC SL CE2 NC CE1 CK DI NC OSCGND ROM_VDD DO DGND NC VDD_3.3 NC NC NC NC AUDIOGND L ch R ch
RF ground FM antenna input power supply O signal level I chip enable-2 non connection I chip enable-1 I clock I data in non connection osc ground power supply I O data out digital ground non connection power supply non connection non connection non connection non connection audio ground L channel output R channel output
O O
AM antenna input high impedance AMANT pin is connected with an all antenna by way of 4.7 H. (LAU type inductor) A series circuit including an inductor and a resistor is connected with RF ground for the countermeasure against the hum of power transmission line. Ground of antenna block Input of FM antenna 75 ohm Surge absorber (DSP-201M-S00B) is necessary. The power supply for analog block. D.C 8.4 V 0.3 V Output of FM/AM signals level Chip enable for EEPROM Low active Not used Chip enable for AFRF High active Clock Data input Not used Ground of oscillator block Power supply for EEPROM pin 13 is connected with a power supply of micro computer. Data output Ground of digital block Not used The power supply for digital block. 3.3 V 0.2 V Not used Not used Not used Not used Ground of audio block FM stereo L-ch signal output or AM audio output FM stereo R-ch signal output or AM audio output
DEH-4000UB/XS/EW5
5 6 7 8
21
- LCD(YAW5091)
A
SEGMENT
22
DEH-4000UB/XS/EW5
1 2 3 4
COMMON
5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
Power ON
Vcc = 5 V Pin 16
Starts communication with Grille microcomputer. 300 ms SWVDD Pin 49 H 300 ms Source keys operative In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300 msec, the oscillator may be defective.
Source ON
SYSPW H Pin 48
F
DEH-4000UB/XS/EW5
5 6 7 8
23
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing.
(1) Basic Indication Method 1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before.
2) Head unit display examples Depending on display capability of LCD used, display will vary as shown below. xx contains the error number. 8-digit display ERROR-xx 6-digit display ERR-xx 4-digit display E-xx
(2) Error Code List Displayed error code Description of the code and potential cause(s) Code Class Electricity Carriage Home NG CRG can't be moved to inner diameter. 10 CRG can't be moved from inner diameter. SERVO LSI ComC
-> Failure on home switch or CRG move mechanism. Communication error between microcomputer and SERVO LSI. Focusing not available. -> Stains on rear side of disc or excessive vibrations on REWRITABLE. Spindle not locked. Sub-code is strange (not readable). -> Failure on spindle, stains or damages on disc, or excessive vibrations. A disc not containing CD-R data is found. Turned over disc are found, though rarely. CD signal error. AGC protection doesn't work. Focus can be easily lost. -> Damages or stains on disc, or excessive vibrations on REWRITABLE. Failed to reach target address. -> CRG tracking error or damages on disc. Skip setting for all track. (CD-R/RW) Mechanical error during CD ON. -> Defective loading motor, mechanical lock and mechanical sensor. Power (VD) is ground faulted. -> Failure on SW transistor or power supply (failure on connector).
17
D
30 44 50 A0
System
Power Supply NG
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.
24
DEH-4000UB/XS/EW5
1 2 3 4
USB error Message Cause No songs in the USB device NO AUDIO USB memory with security enabled is connected The connected USB device contains WMA files that are protected by DRM All the files in the USB device are protected by DRM The connected USB device is not supported by this unit The USB connector or the USB cable is short-circuited CHK USB The connected USB device consumes more than 500 mA (max. allowable current) Confirm the USB device. Turn the ignition switch OFF and ON. Disconnect the USB device, and connect it again. Change to a different source. Then, return to the USB. ERROR-23 USB device is not formatted with FAT16 or FAT32 Format the USB device with FAT16 or FAT32.
C
Action Transfer the songs to the USB device. Follow the USB memory instructions to disable the security. Play an audio file not protected by DRM. Transfer the songs not protected by DRM to the USB device. Connect a USB device that is compliant as a Mass Storage Class. Confirm the USB connector or the USB cable.
N/A USB
ERROR-19
Communication failure
DEH-4000UB/XS/EW5
5 6 7 8
25
EW5
AUX
ANTENNA
1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16
POWER SUPPLY
1. 2. 3. 4. 5. 6. 7. 8. FR+ RR+ FRRRFL+ RL+ FLRL9. 10. 11. 12. 13. 14. 15. 16. TEL NC B.REM NC NC ACC GND B.UP
ES,CN5
AUX
ANTENNA
1 3 5 7 9 11 13 15
FRONT OUTPUT
E
2 4 6 8 10 12 14 16
POWER SUPPLY
1. 2. 3. 4. 5. 6. 7. 8. FR+ RR+ FRRRFL+ RL+ FLRL9. 10. 11. 12. 13. 14. 15. 16. TEL NC B.REM NC NC ACC GND B.UP
26
DEH-4000UB/XS/EW5
1 2 3 4
6. SERVICE MODE
6.1 CD TEST MODE
A
1) Cautions on adjustments In this product the single voltage (3.3 V) is used for the regulator. The reference voltage is the REFO1 (1.65 V) instead of the GND. If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servos misoperation will apply excessive shock to the pickup. To avoid such problems: a. Do not mix up the REFO1 with the GND when connecting the (-) probe of measuring instruments. Especially on an oscilloscope, avoid connecting the (-) probe for CH1 to the GND. b. In many cases, measuring instruments have the same potential as that for the (-) probe. Be sure to set the measuring instruments to the floating state. c. If you have mistakenly connected the REFO1 to the GND, turn off the regulator or the power immediately. Before mounting and removing filters or leads for adjustment, be sure to turn off the regulator. For stable circuit operation, keep the mechanism operating for about one minute or more after the regulator is turned on. In the test mode, any software protections will not work. Avoid applying any mechanical or electrical shock to the mechanism during adjustment. The RFI and RFO signals with a wide frequency range are easy to oscillate. When observing the signals, insert a resistor of 1k ohms in series. The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it.
2) Test mode This mode is used to adjust the CD mechanism module. To enter the test mode. While pressing the SOURCE and RPT keys at the same time, reset. To exit from the test mode. Turn off the ACC and back up. Notes: a. During ejection, do not press any other keys than the EJECT key until the loaded disc is ejected. b. If you have pressed the (->) key or (<-) key during focus search, turn off the power immediately to protect the actuator from damage caused by the lens stuck. c. For the TR jump modes except 100TR, the track jump operation will continue even if the key is released. d. For the CRG move and 100TR jump modes, the tracking loop will be closed at the same time when the key is released. e. When the power is turned off and on, the jump mode is reset to the singleTR (91), the RF amp gain is set to 0 dB, and the auto-adjustment values are reset to the default settings.
DEH-4000UB/XS/EW5
5 6 7 8
27
The specification of the 08 model does not include the 1 - 6 keys issuance function for H/U and the remote control unit. Therefore, in order to issue commands in a slave test, use the direct FUNCTION keys alternatively to enable the equal key command sending function to the existing models.
Outline) Use the direct FUNCTION keys to display, select, or issue the KEY 1 - 6. <Direct FUNCTION keys and corresponding functions> Direct FUNCTION key Normal mode A ASR/SAT/FUNC1 B RDM/SHFL/FUNC2 C LOCAL/RPT/FUNC3
Slave test mode Selecting a key command Issuing a key command Switching a screen
For convenience, a name of each direct FUNCTION key is shown as "A", "B", and "C".
B
How to issue the 1 - 6 keys for the CDS source: (The areas below are overwritten and displayed on character strings for the normal mode display.) 1 During the slave test mode, the key name "K1" is shown at the left by default. In this condition, press the A key to toggle K1 - K6, and select a command to be sent to the slave.
C K
O 1
P !
C T
T !
D ! TRK
C ! ! ! ! SECOND
FOLDER
MINUTE
A key
C
C K
O 6
P !
C T
T !
D !
C ! ! ! !
2 During the K1 - K6 key names are displayed, press the B key and issue the selected command.
C K
O 1
P !
C T
T !
D !
C ! ! ! !
3 Press the C key to change display/non-display of key names. When the non-display mode is selected for the K1 - K6 key names, "A key" and "B key" are invalid.
C K O 1 M P ! A C T T ! D ! I S C ! ! ! !
C key
C F
O -
M !
P !
C T
T !
D !
C ! ! ! !
28
DEH-4000UB/XS/EW5
1 2 3 4
- Flow Chart
[Key] Contents Display
[CD] or [SOURCE] Source On TRK MIN SEC [SOURCE] + [RPT] + Reset or [SOURCE] + [RPT] + BU + ACC Test Mode In
00
00
00
99
99
99
GG
GG
GG
SP
SP
SP
[1]
[>] CRG +
[<] CRG -
*2
TRK MIN SEC
[5] Gop Mode *10 Gop Mode switching TRK MIN SEC
91
91
91
0X
0X
0X
00 00 00 or 99 99 99
*8 00 00 00 or 99 99 99
*8 00 00 00 or 99 99 99
??
??
??
OL
OL
OL
[>] CRG +
[<] CRG -
??
??
??
8X 8X 8X or 9X 9X 9X
8X 8X 8X or 9X 9X 9X
??
??
??
*4
TRK MIN SEC TRK MIN
*4
SEC
??
??
??
8X 8X 8X or 9X 9X 9X
8X 8X 8X or 9X 9X 9X
*1)
TRK
TYP
MIN SEC
->
TRK
+ 6 dB -> 06MIN06SEC06
TRK
+ 12 dB 12MIN12SEC12
*2) Focus Close -> S.Curve -> TRK TRK 00MIN00SEC00 01MIN01SEC01 (TRK99MIN99SEC99)
Operation Test Mode Power On/Off CRG + / TR Jump + (Direction of the external surface) CRG - / TR Jump (Direction of the internal surface) T. CLS & AGC & Applicable servomechanism / AGC,AGC display setting RF Gain switching / Offset adjustment display / T.Balance adjustment / T. Open F. Close,S Curve / Rough Servo and RF AGC / F,T,RF AGC SPDL 1X/2X switching As for the double speed(2x), audio output cannot be supported. Error Rate measurement ON : ERR 30 Counts Start BER display data[%] F. Mode switching / Tracking Close / CRGTR Jump Switching
*3) F.Offset Display -> RF.Offset -> T.Offset Display -> Switch to the order of the original display
[2] [3]
*4) 1TR/4TR/10TR/32TR/100TR *5) Single -> 4TR -> 10TR -> 32TR -> 100TR -> CRG Move 9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86) *6) Only at the time of CRG move, 100TR jump *7) TRK/MIN/SEC -> F.AGC -> T.AGC Gain -> F Bias -> RF AGC
[4]
[5]
[6]
TYP (1X)
MIN SEC
->
TRK
2X -> 22MIN22SEC22
TRK
1X 11MIN11SEC11
*10)
OFF(TYP)
TRK MIN SEC
->
TRK
TRK
TRACKING 71MIN71SEC71
As for the double speed (2x), audio output cannot be supported After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete. When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens sticks to Wall, causing the actuator to be damaged). In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released. When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting.
DEH-4000UB/XS/EW5
5 6 7 8
29
7. DISASSEMBLY
- Removing the Keyboard Unit (Fig.1)
A
1
Cover
1
Fig.1
- Removing the Holder (Fig.2) Take off the pick of left and right and then a holder slide to the arrow course.
Pick
Fig.2
Holder
C
Case
Fig.3
Take off four picks of the part of the arrow and then remove the Panel.(Fig.4)
E
Panel
Fig.4
30
DEH-4000UB/XS/EW5
1 2 3 4
Push the place of the arrows and then remove the Panel Assy.
Fig.5
Panel Assy
Fig.6
1 1
Remove the four screws.
1 1
Fig.7
D
CD Mechanism Module
DEH-4000UB/XS/EW5
5 6 7 8
31
1 1
1
Fig.8
2 3
Remove the screw and then remove the Tuner Amp Unit.(Fig.9)
2
C
Fig.9
32
DEH-4000UB/XS/EW5
1 2 3 4
a B B
Upper Frame
B B
D
B B A
Damper
A
DEH-4000UB/XS/EW5
5 6 7 8
33
1. Apply Shorting Solder to the flexible cable of the Pickup, and disconnect it from the connector. 2. Unsolder the four leads, and loosen the Screw. 3. Remove the CD Core Unit. Caution: When assembling the CD Core Unit, assemble it with the SW in a clamped state so as not to damage it.
Shorting Solder
Screw
CD Core Unit
Solder
1. Make the system in the carriage mechanism mode, and have it clamped. 2. Remove the CD Core Unit and remove the leads from the Inner Holder. 3. Remove the Poly Washer, Change Arm, and Pickup Lock Arm. 4. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw. Caution: When assembling, move the Planet Gear to the load/eject position before setting the Feed Screw in the Inner Holder. Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load Carriage Motor Assy, do not make them loose over the Feed Screw.
Poly Washer Change Arm Pickup Lock Arm Inner Holder
Feed Screw
Planet Gear
Pickup Rack
Chassis
Pickup
34
DEH-4000UB/XS/EW5
1 2 3 4
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode cancelled), shift the TESTIN IC601(Pin 63) terminal to H. The clock signal is output from the PCL terminal IC601(Pin 39). The frequency of the clock signal is 468 750 Hz that is one 32th of the fundamental frequency. The clock signal should be 468 750 Hz (-10 Hz, +15 Hz) If the clock signal out of the range, the Xtal (X601) should be replaced with new one.
B
DEH-4000UB/XS/EW5
5 6 7 8
35
Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below. Purpose : To check that the grating is within an acceptable range when the PU unit is changed.
B
Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. Method : Measuring Equipment Measuring Points Disc Mode
CD CORE UNIT
C
Oscilloscope
F VREF
D
Checking Procedure 1. In test mode, load the disc and switch the 3 V regulator on. 2. Using the -> and <- buttons, move the PU unit to the innermost track. 3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourth press. 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75 degrees. Refer to the photographs supplied to determine the phase angle. 5. If the phase difference is determined to be greater than 75 degrees try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75 degrees then the mechanism should be judged to be at fault. Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble".
36
DEH-4000UB/XS/EW5
1 2 3 4
Grating waveform
0 degrees
30 degrees
45 degrees
60 degrees
75 degrees
90 degrees
DEH-4000UB/XS/EW5
5 6 7 8
37
The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) "
9.1 PACKING
B
38
DEH-4000UB/XS/EW5
1 2 3 4
Mark No. 16 17
Part No. YHP5040 YXB5009 See Contrast table(2) See Contrast table(2) See Contrast table(2)
(2) CONTRAST TABLE DEH-4000UB/XS/EW5, DEH-3050UB/XS/ES and DEH-3050UB/XU/CN5 are constructed the same except for the following:
Mark No.
1 2 * 3 4 13 14 18-1 18-2 18-3 18-4 18-5 * 18-6 18-7 20 21 * 22 23
Description
Cord Assy Polyethylene Bag Attachment Assy Screw Unit Box Contain Box Owner's Manual Owner's Manual Owner's Manual Owner's Manual Installation Manual Warrnty Card Caution Card Cord Assy Remote Control Assy Battery Cord Assy
DEH-4000UB/XS/EW5
CDP1015 CEG-162 YEA5036 BPZ20P060FTC YHG5400 YHL5400 YRB5071 YRD5180 YRD5181 YRD5182 YRD5189 CRY1265 Not used Not used Not used Not used Not used
DEH-3050UB/XS/ES
Not used CEG1373 YEA5037 Not used YHG5402 YHL5402 YRD5184 YRD5185 Not used Not used YRD5190 Not used CRP1310 Not used CXC8885 CEX1065 CDP1017
DEH-3050UB/XU/CN5
Not used CEG1373 YEA5037 Not used YHG5406 YHL5410 YRB5072 Not used Not used Not used
D C
Language
DEH-4000UB/XS/EW5
5 6 7 8
39
9.2 EXTERIOR(1)
40
DEH-4000UB/XS/EW5
1 2 3 4
Mark No. 21 22 23 24 25
Description Screw Screw Pin Jack(CN351) Plug(CN901) Connector(CN701) Connector(CN803) Antenna Jack(CN401) FM/AM Tuner Unit(Y401) Holder Holder Fuse(10 A) Jack(CN621) Holder
Part No. BSZ26P060FTC BSZ26P200FTC See Contrast table(2) CKM1376 CKS3833 CKS5664 CKX1056 See Contrast table(2) CND4324
B
31 32 > 33 34 35
(2) CONTRAST TABLE DEH-4000UB/XS/EW5, DEH-3050UB/XS/ES and DEH-3050UB/XU/CN5 are constructed the same except for the following:
Mark
NOTE
No.
4 10 19 24 29 34 35
Description
Sheet Chassis Unit Tuner Amp Unit Pin Jack(CN351)
DEH-4000UB/XS/EW5
Not used YXA5359 YWM5203 CKB1057
DEH-3050UB/XS/ES
Not used YXA5196 YWM5205 CKB1051 CWE2098 YKS5017 YNC5055
DEH-3050UB/XU/CN5
CNM9404 YXA5196 YWM5207 CKB1051 CWE2098
D
FM/AM Tuner Unit (Y401) CWE2097 Jack (CN621) Holder YKS5001 YNC5054
YKS5017 YNC5055
DEH-4000UB/XS/EW5
5 6 7 8
41
9.3 EXTERIOR(2)
B
C
42
DEH-4000UB/XS/EW5
1 2 3 4
Mark No. 17 18 19 20
Description LCD (LCD1801) Connector(CN1802) Holder Sheet Lighting Conductor Connector Grille Unit Knob Unit(MULTI-CONTROL) Spring
Part No. YAW5091 YKS5027 YND5015 YNM5105 YNV5136 YNV5140 See Contrast table(2) See Contrast table(2) YBL5013
A
22 23 24 25
(2) CONTRAST TABLE DEH-4000UB/XS/EW5, DEH-3050UB/XS/ES and DEH-3050UB/XU/CN5 are constructed the same except for the following:
Mark No.
2 3 4 7 23 24 26
Description
Remote Control Assy Cover Cord Assy Detachable Assy Grille Unit Knob Unit (MULTI-CONTROL)
DEH-4000UB/XS/EW5
Not used Not used Not used YXA5353 YXA5345 YXA5350
DEH-3050UB/XS/ES
CXC8885 CNS7068 CDP1017 YXA5354 YXA5346 YXA5351 YXA5365
DEH-3050UB/XU/CN5
CXC8885 CNS7068 CDP1017 YXA5355 YXA5346 YXA5351 YXA5365
YXA5364 Button Unit (SRC/OFF, DISP/BACK/ SCRL, BAND/ESC, MUTE) Cushion IC(IC1802) Cord Assy Pin Not used Not used CDP1015 CKX-003
27 28 29 30
DEH-4000UB/XS/EW5
5 6 7 8
43
19 27 5
5 19
(1)
19 13
(1)
29
48 5 19
20 57
B
66 9 44 44 15 60
(2)
13
16
(1)
25 54
(1)
23 31
C
9 72 8
(2)
58 69 71 70
73 21
46 38 39 33 62
70 68 40 28 32
(1) (1) (1)
63
7 50
4 36 47 17 35 37 14
(2)
(1)
B
(1) (1) (2)
4 61
(2)
52
C
53
18
45 12 64
(1)
41 5
6
(2)
(1)
49
D
8 51 55
65
(1) (2)
51
59
(1) (1)
C
74 1 3
E
43 10
(2) (1)
56
D
22 34
(1) (1)
19
(1)
(1)
11 42 24
(1) (1) (1)
26
19 67
F
30
44
DEH-4000UB/XS/EW5
1 2 3 4
Description
Roller Holder Arm Guide Arm Arm Arm Clamper Arm Guide Arm Collar Motor Unit(M2) Arm Unit Chassis Unit Gear Unit Frame Unit Motor Unit(M1) Screw Unit Screw Screw Washer Pickup Unit(P10.5)(Service) Screw
CNV8343 CNV8344 CNV8345 CNV9498 CNV8348 CNV8349 CNV8350 CNV8365 CNV8386 CNV8396 CNV9521 CNV8447 CXC4026 CXC4027 CXC4028 CXC4029 CXC4031 CXC7134 CXC6359 JFZ20P025FTC JGZ17P022FTC YE20FTC CXX1942 IMS26P030FTC
C B
DEH-4000UB/XS/EW5
5 6 7 8
45
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST".
A-a A-b
A-a
C
CDVDD BRXEN CDRST BDATA
CN701
USBGND 2 USBGND 1 CDGND CDGND AGND PGND CDR CDL DM 3 DP 4
EW5:CWE2097 ES,CN5:CWE2098
Y401
Rch 24 Lch 23 BEGND 22 RDS_HSLK 21 RDS_LOCK 20 RDS_DATA 19 RDS_CK 18 VDD_3.3 17 COMP 16 DGND 15 DO 14 ROM_VDD
TUNR
BSRQ VD VD
TUNL
6 C1
RDS
5 B2 4 E2 6 C1 5 B2 4 E2 UMH1N
RDS-HSLK RDS-LOCK
VD
19
18
17
16
15
14
13
12
11
10
BSRQ
Q401
CDR
CDL
UMH1N
E1 1
B1 2
C2 3
CDVDD
RCK T3V
Q402
A-a
A-b
Guide page
RDAT
R415
220
R408 R410 R409 R411 22K 22K 22K 22K
RDS-DATA C720
VDD
BRXEN
CDRST
DM
UG
AG
PG
DP
R413
220
RDS-CK
BSCK
BRST
RLK
GND
CN701
1 Q702 2SD2396 Q701 6 2C 1B 1E RT3T22M 2E 1 2B 2 1C 3
HZS7L(C3) D701 C701 R047
RHSLK
BSCK
BRST
USGND3
E1 1
B1 2
C2 3
EW5
GND
TUNG DO T5V
C407
3 OUT 2 GND
NJM2885DL1-33 IC401
1 IN
A-a
A-b
Detailed page
OSCGND 12 LDET
VCC
13
OSCG LDET
EW5
R402
47/6R3 R01 C402 C401
L403
C408
R414
4R7 C410 R47
BDATA
GND
B.UP GND
R407
VCC
SL
VDD
C411
47P
NJM2885DL1-33
ES
ZNR401
100/10
1 IN
R709
1K R711
R713
IMSA-6801-01Y901
3
C709 1
C154
1 GND GNDGND
VDCONT
C708
C710
22/10
R47
R708
R710
R712
R627
D621
GND
220 220
AUXR
USDP
TUNR
BSCK
RX
SYNC
TX
VDCONT
CDRST
RST
AUXR
GND
4700P C621
R625 22K
EZJZ1V270RM
FLG
ROT0
USBCTL
/DSENS
CN621
REAR AUX
6 5 4 3 2 1
AUXL
4700P R626 C622 C623 22K R1
100
R632 100
AUXL
/BSENS
VDD L601
R967
AUXGND
1K
ES,CN5
BZ601 1 R618 1 2 2 CPV1062
FOR WIRED REM. RST
KEY2
WIRED REM.
WIRED REM.
1K
C601 R616 C602 18P 47K R602 18P
EW5
10K
ES,CN5
EXCEPT WIRED REM.
R603 10K
BUZZER
GND
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
NC 11 NC 10
NC 7 NC 6
NC 5 4
NC
C
BDATA BSCK KEY1 DPDT KYDT ILM2
EW5
31 32 33 34 35 36 37 38 PCL 39 40 41 42 43 44 45 46 47 48 49
ROT1
R631
AUXR
GND
GND
NC
VDCONT
NC
RX
XOUT RESET
SYNC
TX
ROT0
ROT1
BYTE
BSCK KEYD DPDT KYDT ILM2 NC PCL ASENBO MUTE TELIN BRST BRXEN BSRQ ANTPW DALMON
ROMDATA TUNPCE2 TUNPCE1
IC601
ASENBO MUTE TELIN /BRST BRXEN /BSRQ US5V ANTPW DALMON SYSPW SWVDD OELPW
EW5:PEG475A ES,CN5:PEG409A
SYSTEM CONTROLLER
SYSPW
ILMPW NC ISENS IPPW VCK VDT
TUNPDO
TUNPCK
RDSDT
ASENS
RDSLK
LDET
VCC
RCK
VSS
VST
NC
NC
NC
NC
NC
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
VDD
5 4
VOUT
VIN
R5523N001B
C251
R257
C252
10K
R1
IC251
R1
TEST
R610 47K
GND
FLG
EN
R620
R607
FLG
680
GND
R617 47K C253 R01
C609 47P
USBCTL USBCTL
R604 680 R605
5V
680
0R0
FLG
R619
B.UP
S5688G
BD9781HFP IC501
GND
EW5
INV EN TUNPDO TUNPCK
0R0
RDS-LOCK
RDS-DATA
VCK
VST
CE2
C502
220/16
C504
R513
1
R512 0R0
SYNC
R507 2R2K
SYNC
RT
R510
L501
D501
SW
3300P C506 82K RB060L-40
C507
14.1V
R841
4R7K R842
R1
C505
R506
100P
8R2K
R505
68K
10K
B.UP
US B 5 V
GND
FB
R511
GND VDD
ILM
GND
470
USB5V
GND
R808 100K
R849
ILMPW
GND
2R2K
CE1
RDS-HSLK
D502
VIN
SW
RT
FB
TUNPDI
RDS-CK
/ASENS
ILMPW
ISENS
IPPW
LDET
VDT
R811
10K
80
NC
SWVDD 50 OELPW
RDS57K
ROMCK
ROMCS
TUNPDI
TESTIN
GND
EZJZ1V270RM D810 EZJZ1V270RM EZJZ1V270RM D801 EZJZ1V270RM EZJZ1V270RM D803 EZJZ1V270RM EZJZ1V270RM D805 EZJZ1V270RM R836 0R0 R813 D809 D802 D804 D806 100K
GND GND
CN803
DGND SWVDD JOYST USBGND 1 2 3 4 5 6 7 8 9 10 11 12 13 14
47K
DG SW5V TP1 TP2 DPDT KYDT IMG TP3 TP4 ILMB TP5 TP6 TP7 DSEN
GND
R806 2R2K 2R2K R807 R804 2R2K R805 2R2K R814 1K R815 1K
B
CN1801
A
46 DEH-4000UB/XS/EW5
1 2 3 4
C605
BSO BSI
100 NC 99 AVCC 98 VREF 97 SL 96 AVSS 95 MODEL 94 KEYAD 93 NC 92 SSENS 91 NC 90 NC 89 NC 88 RGBST 87 RGBCK 86 RGBDT 85 NC 84 NC 83 NC 82 JOYST NC 81
USBCTL
DSENS
VCC
CDRST
CNVSS
PEE
BSENS
FLG
RX2
VSS
NMI
XIN
NC
AUXL
REAR AUX IN
AUXGND
AUX1:+2.2dBs
BRXEN
CDRST
BDATA
/BSRQ
/BRST
220
USDM
1K
C156
220
220
GND
C412
C153
100K
100K
VCC1
CN401
3 OUT 2 GND
IC702
C159
GND
2
R707
R22
1 IN5-_L IN5+_R 2 IN5+_L IN4+_R 3 IN4+_L IN4-_R 4 IN4-_L IN3_R 5 IN3_L IN2_R 6 IN2_L IN1 R
680 11 DI GND R403 DI R404 10 CK 680 CK R405 9 CE1 680 CE1 8 680 WC R406 7 CE2 CE2 6 SL 680 SL 5 T8V VCC FM 4 FM_ANT 3 RFG RF_GND AM L402 2 AM_ANT 1
22/10 C403
R01 C404
4R7(1/4W)
ES,CN5
LDET TUNPDI TUNPCK CE1 CE2
28
27
26
25
R421
0R0
24
23
GND
EW5
GND
GND
CD/USB: +0.6dBs
C705
A-b
A
ND SWR C352 2R2/50 C704 1 GND SWL R351
R360 22K
820
1 E1 2 B1 3 C2 Q351 RT3N66M
R359
6 C1 5 B2 4 E2
12V C705 1
IC151
C351 2R2/50
R356 820
R352 0R0
R384 0R0
CN351
1 2 3 RCRR RCRL SWR SWL RCFR RCFL RCG1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
22K
1 IN5-_L IN5+_R 2 IN5+_L IN4+_R 3 IN4+_L IN4-_R 4 IN4-_L IN3_R 5 IN3_L IN2_R 6 IN2_L IN1_R 7 IN1_L GND 8 Vref STB 9 Vcc CLK 10 Front_L DATA 11 Rear_L Front_R 12 Pre/SW_L Rear_R 13 Vp Pre/SW_R 14 Pref PGND
PML018A
4 5 6
R393 R394
FOR 2P/O
0R0
7
0R0
VCC
R22 1
ES,CN5
FM(10%): -12.0dBs(EW5), -16.0dBs(ES,CN5) AM(15%): -7.5dBs(EW5), -11.5dBs(ES,CN5) CD/USB: -9.3dBs AUX1: -9.7dBs
1K R180 0R0
8 9
L161
C159
10
C155 R22
VCC1
C153
C156
ES,CN5
FR C3 5 6 2R2/50 R355 820
1 E1 2 B1 3 C2 RT3N66M Q353
R151
1K R152
C165 10/16
C163
R153
C160 10/16
C154
C162
R1
R627
47/10
1K
R3 8 2
R364 22K
1K
0R0
AUXGND
AUXR
TUNR
AUXL
TUNL
VCK
VDT
VST
1 FU353 2
R363 22K
ROT0
ROT1
FL
C355 2R2/50
R358 820
01 GND
R301 R303 R304 R306 470 470 470 470
R381
0R0
6 C1 5 B2 4 E2
GND
CEK1286 3A
>
ACGND
IC301
PGND PGND STBY RRIN VCC SVR RR+ TAB RL+ RRRL-
PAL007C
B.REM 25 AGND PGND PGND 24 MUTE 22 FRIN RLIN FLIN VCC FR+ FL+ FRFL23
10
11
12
13
14
15
16
17
18
19
20
1SS133
VDD
NC 6 NC 5 4 3 2 1
D454
21
B.UP
MUTE
GND
NC
NC
NC
ROT0
ROT1
4 1K(1/4W)
R454
100
C605 C604 1 10/16
L602
C606 10/16 C607 R1
RDS57K
S-80835CNMC-B8U
RDSDT
ASENS
RDSLK
LDET
IC961
NC
NC
NC 99 AVCC 98 VREF 97 SL 96 AVSS 95 MODEL 94 KEYAD 93 NC 92 SSENS 91 NC 90 NC 89 NC 88 RGBST 87 RGBCK 86 RGBDT 85 NC 84 NC 83 NC 82 JOYST NC 81
79 80
GND
RT3T22M
C309
2C
1E
1B
SL
R47 C306
Q453
C313
C901
3 1C
1 2E
2 2B
ES,CN5
SSENS
GND
10/16
C311
C310
R47
R47
RR2
RR1
FR1
FR2
RL2
RL1
FL1
GND
VCC
R451 10K
R453 15K
C451
Q451 RT1N241M
33/10
RGBCK
MUTE
220
D903
RGBST
S5688G
S5688G D904
CONTROL
GND
NJM2388F84 10K 5 4
8.4V
VOUT VIN IC921 GND
FL2
GND
R1
R47 C305
R47 C315
EW5
N.C2
N.C1
JOYST
OUT
VDD
VSS
C921
C922
R922
C923
220/10
100/16
C924
S5688G
R01
GND2 GND1
R01
8.4V
VDD
47K
>
VCC
75
76
77
78
14 13
14 13 12 11 10 9 8 7 6 5 4 3 2 1
8R2K
R962
R047
C961
GND 5V
VDD
RST GND
2SD2396 Q911
R911 R912 22K
12 GND 11 10 9 RL2 8 7 6 5 4 3 2 1
B.REM
C962
RT3T22M 1E 1B 2C Q912
13V 4 5 6
C913 1000/16
47/10
C911
VDD
10/16
GND
RESET
3 1C
HZS6L(B2)
2 2B
D912 R01 C912
1 2E
SYSPW DALMON
GND
0R0
VDD
RR1 FR1
R613 100K
RDS-LOCK RDS-DATA RDS-HSLK
/ASENS
CN901
VDD EW5,ES:RT3CLLM CN5:UMX1N Q931
6 C1 5 B2 4 E2
RR FR FL RL RR + FR + FL + RL +
LDET
ILMPW
R931
/ASENS
VDD
BS1 D931
R934 47K
BACK UP
B. REM
HZS7L(C3)
GND ACC
SWVDD
5V
2R2K R853
GND /BSENS
4R7K R852
L852
C851 R1
R851 15K
1 E1 2 B1 3 C2
D932 HZS7L(A1)
4R7K R937
R938 1K(1/4W)
Q851 2SA1036K
Q852 RT1N141M-11
SWVDD GND
ASENS BSENS
GND
E
R849 R811 10K 47K
R952 1K
R813
R951
100K
47K
Q951 2SA1037K
MC2848-11 GND
TELIN
TEL MUTE
GND
EW5
ROT1
ROT0
R825 1K
R846 0R0 R847 0R0 R848 0R0
/DSENS
NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors.
Decimal points for resistor and capacitor fixed values are expressed as : 2.2 t 2R2 0.022 t R022
The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
US5V
USDP USDM
A
DEH-4000UB/XS/EW5
5 6 7 8
47
1 C604 C155 R22 VCC1 C605 C160 10/16 C163 R1 C162 C606 R1 10/16 C607 47/10 R180 0R0 C165 10/16 L161 3 4 1 10/16 TUNL 5 6
26 25 24 23 22
GND
GND
L602
9 10 11 12 13 14
20 19 18 17 16 15
IN5+_L IN4+_R IN4+_L IN4-_R IN4-_L IN3_R IN3_L IN2_R IN2_L IN1_R IN1_L GND Vref STB Vcc CLK Front_L DATA Rear_L Front_R Pre/SW_L Rear_R Vp Pref Pre/SW_R PGND
PML018A
VDT
R151 1K
ES,CN5
R606 10K
VCK
R152 1K
VST
R153 1K
R452
220
VCC
15K(1/4W)
1 2
RT3N66M
PGND
ES,CN5
FOR 2P/O
IC301
0R0 R393
PAL007C
CEK1286 3A
GND
GND
13 14
B.UP
>
C310 FR1
C309
15 16
0R0 R394
17 18
FR2
19 20 21 22
CN351
GND2 GND1
BUP G
FL1
S5688G
FL2
23 24 25
10
FLPGND B.REM
8.4V
RL2
R3 8 2
3 4
RL1
GND
5 6
R363 22K
R364 22K
R359 22K
R360 22K
RR2
VCC
7 8
21
MUTE
FM(10%): -12.0dBs(EW5), -16.0dBs(ES,CN5) AM(15%): -7.5dBs(EW5), -11.5dBs(ES,CN5) CD/USB: -9.3dBs AUX1: -9.7dBs
48
A-b
A-a A-b
SWL SWR C352 2R2/50 820 R351
1
12V C351 2R2/50 820 R356 R352 0R0 1 RCRR
DEH-4000UB/XS/EW5
2
R609 100K R608 100K KEY2 SSENS RGBST SL GND R451 R47 C305 R47 R47 C315 R47 GND GND
3
VDD B.UP
3
FOR WIRED REM.
EW5
JOYST
RGBCK
MUTE
10K
C308
FL
FR
2R2/50
C355 R358
C3 5 6 R355
820 0R0
ES,CN5
1 FU353 2
S5688G
CEK1208 16 B.UP 16 10A
>
SWL
RCFL
RCRL
SWR
RCFR
RCG1
R452
D903
R453
33/10
C451
RGBDT Q451 RT1N241M D904 GND GND B.UP L901 600 H BUP2 BUP1 S5688G
R01 5 4 CONTROL GND VOUT VIN IC921
8.4V
R606
10K
EW5
4 3 2 N.C2 N.C1 1 IC961 VCC
NJM2388F84
JOYST
S5688G
OUT
VDD
VSS
47K
C921
C922
R922
C923
C924
R01 220/10
100/16
S-80835CNMC-B8U
VDD
8R2K
R962
R047
C961
3
MUTE S5688G
RGBCK
VCC
RGBST
>
14 13
GND2 GND1
8.4V D901 S5688G D902 BUP3 S5688G GND D911 RL2 FL2 RL1 FL1 RR2 FR2
22K
12 11 10 9 8 7 6 5 4 3 RR1 FR1 2 1
10/16
C962
R911
13V 1E 4 5 6
C913 1000/16
47/10
C911
2 2B
D912 R01 C912
1B 2C Q912
1 2E
DALMON GND
HZS6L(B2)
SYSPW
1R5K(1/4W)
VDD GND 3 1C
RESET
R912
R931
/ASENS
6 C1 5 B2 4 E2 R934 47K
VDD
5V 47K
R936 47K
L852
R851
/BSENS
1 E1 2 B1 3 C2
R853
2R2K
C851
R1
R852
4R7K
R937
Q851 2SA1036K
Q852 RT1N141M-11
SWVDD GND
4R7K
R951
47K
0R0
R848
US5V
R846 0R0
R847 0R0
5
RST RT3T22M
GND
4
VDD
VDD EW5,ES:RT3CLLM CN5:UMX1N Q931 D931 HZS7L(C3) BS2 R933 100K GND AS2AS1 R935 D932 HZS7L(A1) R938 1K(1/4W) BS1
R613
100K
CN901
BACK UP
B. REM
6
R952 1K Q951 2SA1037K GND VDD R953 4R7K D951 MC2848-11 TELIN GND
GND ACC
RR FR FL RL -
RR + FR + FL + RL +
SWVDD
15K
ASENS BSENS
GND
DEH-4000UB/XS/EW5
EW5
L951
R955 15K(1/4W)
7
A-a A-b
TEL MUTE
GND
R837
JOYST
0R0
DPDT
KYDT
5
The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Decimal points for resistor and capacitor fixed values are expressed as : 2.2 t 2R2 0.022 t R022 NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors.
8 E A D C B
ROT1
ROT0
R825
/DSENS
1K
USDP
USDM
A-b
49
VD
VD
BSRQ
BRST
BSCK
BRXEN
BDATA
CDRST
CDVDD
CDGND
CDR
AGND
CDL
CDGND
PGND
DP
DM
USBGND
23
BEG
BEGND
9 8 7 6 5 4 3 2 19 18 17 16 15 14 13 12 11
RDS
RDS-HSLK RDS-LOCK
5 B2 4 E2 10 1
6 C1
5 B2
BSRQ
BRST
Q401
Q402
EW5:CWE2097 ES,CN5:CWE2098
E1 1
B1 2
18
B1 2 C2 3
T3V
C2 3
RDS_CK
UMH1N
19
RCK
UMH1N
20 220 RDS-DATA
16 GND 6 2C 1B 1E
C701 R047 3 OUT 2 GND 1 IN
TUNG NJM2885DL1-33 IC401 Q701 5 R701 4 1C 3 270 (1/4W) RT3T22M GND GND 1
VDD
17 Q702 2SD2396
DGND
15
DO
R401
DO
14 L403
C408 4R7 R01 C402 22/10 C403 R01 C404 C401 C410 R47
ROM_VDD
680
R01
13
OSCG
12
47/6R3
LDET
C407
OSCGND
EW5 ES,CN5
CD/USB: +0.6dBs
HZS7L(C3) D701
E1 1
VDD_3.3
EW5
1
CDL
R415
BSCK
DM
RDS_LOCK
RDAT
6 C1
21 220
RLK
GND USGND3
4 E2
22
RHSLK
CN701
USBGND
24
23
22
21
20
0R0 R703
19
GND
STB
CLK
IN3_R
4 IN4-_L 5 IN3_L
6 IN2_L 7 IN1_L
8 Vref 9 Vcc
L401
C405 C406 R1 100/10
VCC
C411
47P
ES
GND R707
3 OUT 1K 2 GND 1 IN IC702
VCC
1
NJM2885DL1-33
C153
220
R709
C156
C155 R22
C154
C708
C710
R47
22/10
220
220
R708
R710
EZJZ1V270RM D623
R712
EZJZ1V270RM D622
220
C709 1
GND
R627
1K
GNDGND
GND
USDM
USDP
TUNR
AUXR
AUXGND
AUXL
4700P C621
TX
FLG
SYNC
ROT0
CDRST
USBCTL
VDCONT
/DSENS
4700P R626
REAR AUX
AUXGND KEY1 KEY2 BZ601 1 R618 1 2 2 CPV1062 GND 1K
R628 100K R629 100K
C622
C623
AUXGND
22K
R1
100
/BSENS
CN621
100 AUXL
VDD L601
ROT1
R632
RST
AUXL
RX
DEH-4000UB/XS/EW5
100K R714
R711 R713 220
AUXR
GND
TUNL
C160 10/16
GND GND
GND
C163
D621
R1
VCC1
GND
CN401
C412 100K 100K
IMSA-6801-01Y901
C159
L161
ZNR401
R22
680 11 DI GND R403 DI R404 10 CK 680 CK CE1 R405 9 680 CE1 8 680 WC R406 7 CE2 CE2 6 SL 680 SL 5 T8V VCC FM 4 FM_ANT 3 RFG RF_GND AM L402 2 AM_ANT 1 GND
10
Front_L
EW5:1K ES,CN5:0R0 SL
IC151
R407
IN2_R
IN1_R
DATA
WIRED REM.
WREMG
1K
GND
WIRED REM.
18P
47K
C601
ES,CN5
EXCEPT WIRED REM.
R603 10K
R616
R602
10K
BUZZER
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
C602
12
18P
EW5
RST
R967
6 5 4 3 2 1
R622
R621 1K
1K
EW5
31 32
TX
RX
NC
NC
NC 7
NC 6 NC 5
NC
PEE
FLG
RX2
NMI
VCC
XIN
SYNC
VSS
NC 11 NC 10 9
BYTE
ROT0
CDRST
DSENS
BSENS
XOUT RESET
USBCTL
C604
1 10/16
C605
BSCK
33
VDCONT
BSO BSI
CNVSS
ROT1
NC
VST
VCK
VDT
ROMDATA
ROMCK
ROMCS
NC
VCC
TESTIN
VSS
TUNPCE2
TUNPCE1
TUNPCK
TUNPDI
TUNPDO
NC
NC
NC
RCK
LDET
ASENS
RDSLK
RDSDT
RDS57K
NC
NC
50
A-b
A-a
A-a A-b
C
CN701
TUNR TUNL
Y401
RCH
FM(10%):-29.5dBs(EW5) -33.5dBs(ES,CN5)
AM(15%):-26.0dBs(EW5) -30.0dBs(ES,CN5)
Rch
24
LCH
Lch
GND
R402
LDET
EW5
C705
WREM1 WREM2
ES,CN5
BDATA
L602
4
ASENBO MUTE TELIN /BRST BRXEN /BSRQ US5V ANTPW DALMON SYSPW SWVDD OELPW
40 41 42 43 44 45 46 47 48 49
ASENBO MUTE TELIN BRST BRXEN BSRQ ANTPW DALMON SYSPW SWVDD 50 OELPW
EW5:PEG475A ES,CN5:PEG409A
SYSTEM CONTROLLER
100 NC 99 AVCC 98 VREF 97 SL 96 AVSS 95 MODEL 94 KEYAD 93 NC 92 SSENS 91 NC 90 NC 89 NC 88 RGBST 87 RGBCK 86 RGBDT 85 NC 84 NC 83 NC 82 JOYST NC 81
150/6R3 C501
C508
220/16 C502
C504 1
S5688G D502
R502
33K
D501 RB060L-40
GND
1 2 C505 3
R505 8R2K
GND
4 5 6 7
US5V
R510 82K
CN803
GND GND
R836 0R0
R808 100K
SWVDD 50 OELPW
ILMPW
14.1V
ISENS IPPW
ILM
R805
R804
2R2K
ES,CN5:PEG409A
2R2K
R842 4R7K CE2 CE1 TUNPCK TUNPDO TUNPDI R604 680 R605 680
R607 680
SYSTEM CONTROLLER
R620 0R0
R814
R853
R815
RDS-CK R813 100K LDET /ASENS RDS-LOCK R849 10K R811 47K ILMPW RDS-DATA RDS-HSLK R619 0R0
5
5V B.UP BD9781HFP IC501 R513 2R2K R512 0R0 SYNC RT GND
VIN 4
6 6
DEH-4000UB/XS/EW5
USB5V
US B 5 V L501 1 220P R511 470 GND SW 33K INV FB GND R507 2R2K R254 680 VDD USBCTL FLG USBCTL
R1
A-b
A-a
E
BRXEN ANTPW SYSPW DALMON OELPW SWVDD
51
D C A F
A-a A-b
FLG
SYNC
TELIN
/BRST
/BSRQ
B
GND
CN1801
DP
DM 13 DSEN
ILM+
ROT0
ROT1
DGND
JOYST
US5V
DPDT
KYDT
ILMGND
DSENS 14
SWVDD
USBGND
12 TP7
11 TP6
10 TP5
DG
TP4
TP1
TP2
TP3
IMG
ILMB
KYDT R807
SW5V VDD 48 47 46 43 42 49 45 44
51 52 53 54 55 VST 56 VCK 57 VDT 58 ROMDATA 59 ROMCK 60 ROMCS 61 NC 62 VCC 63 TESTIN 64 VSS 65 TUNPCE2 66 TUNPCE1 67 TUNPCK 68 TUNPDI 69 TUNPDO 70 NC 71 NC 72 NC 73 RCK 74 LDET 75 ASENS 76 RDSLK 77 RDSDT 78 RDS57K 79 80 NC NC
TELIN
BRST
BRXEN
BSRQ
ANTPW
DALMON
SYSPW
R816
Q841 2SA1036K
R806
R841
10K
Q842 RT1N141M-11
TEST
GND
GND
C609
47P
EW5
B
1K R825 1K
1K
RGBST
RGBDT
RGBCK
NC 84
NC 83
NC
NC
89
82 JOYST NC 81
85
86
87
88
SWV
5V
EJECT
B
REGION1
REGIO
SRC/OFF DISP/BACK/SCRL
RPT/LO
LIST
S.Rt
BAND/ESC
RDM
EW5
10 100K 5.00MHz
120 10K
560
R1 R1
R1
560
560
EW
B
52 DEH-4000UB/XS/EW5
1 2 3 4
560
B
REGION2 MUTE SW/BASS
KEYBOARD UNIT
REGION2
B
33K
RL
RPT/LOCAL
8R2K
2R2K
3R3K
S.Rtrv
MC2846-11
MC2848-11
2R2K 2R2K
47K
EW5,ES
CN5
A
CN803
CN5
1R5K
470
470
560
560
560
560
470
470
470
EW5,ES USB
B
DEH-4000UB/XS/EW5
5 6 7 8
53
C-a
PICKUP UNIT(P10.5)(SERVICE)
B
F T C S
F T T
T F T F F T T F F T T F
d c
SWITCHES: CD CORE UNIT(S10.5COMP2-USB) S901:HOME SWITCH.........ON-OFF S903:DSCSNS SWITCH.....ON-OFF S904:12EJ SWITCH............ON-OFF S905:8EJ SWITCH..............ON-OFF
S S
C C
e
T S
9 a
7 8 4 5
E
F C C S S
3 2 1
F T T
CD DRIVER
C
54 DEH-4000UB/XS/EW5
1 2 3 4
C-b
C
F T C S
CD CORE UNIT(S10.5COMP2-USB)
SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE
B
b
PE5611B
A
CN701
i j
C
DEH-4000UB/XS/EW5
5 6 7 8
55
56
C-a C-b
C-b C
CD CORE UNIT(S10.5COMP2-USB)
F T C S
1 b
SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE
2
2 3 4
DEH-4000UB/XS/EW5
PE5611B
CN701
i j
C-a C-b
3
DEH-4000UB/XS/EW5
5 6 7 8
C-b
57
58
C-b
C-a
C-a C-b
1 2
PICKUP UNIT(P10.5)(SERVICE)
2
F T C S F
DEH-4000UB/XS/EW5
T F T F F T T F F T T
d c
SWITCHES: CD CORE UNIT(S10.5COMP2-USB) S901:HOME SWITCH.........ON-OFF S903:DSCSNS SWITCH.....ON-OFF S904:12EJ SWITCH............ON-OFF S905:8EJ SWITCH..............ON-OFF
5
5
S S C C
e
6
T S
6
F
9 a
7 8 4 5
C C S S
DEH-4000UB/XS/EW5
3
T
F T
2 1 CD DRIVER
3
8
C-b
C-a
E D
C-a C-b
59
10.4 WAVEFORMS
- CD CORE UNIT
A
Note : 1. The encircled numbers denote measuring points in the circuit diagram. 2. Reference voltage REFO1(1.65 V) 500 ms/div 1DSCSNS 5CLCONT 4LOEJ 6VD 5 V/div 5 V/div 5 V/div 10 V/div 500 ms/div 1DSCSNS 28SNS 312SNS 4LOEJ 5 V/div 5 V/div 5 V/div 5 V/div 500 ms/div
12 cm CD Loading operation
12 cm CD Loading operation
8 cm CD Loading operation
Ref.: GND
B
Mode: Normal
0FIN 200 mV/div 500 ms/div @TE !RFOK(MONI_3) 2 V/div #FE 7SIN 2 V/div
12 cm CD-DA Source On setup operation
$MDX 7SIN
0FIN #FE
60
DEH-4000UB/XS/EW5
1 2 3 4
1 V/div 1 V/div
200 s/div
500 ms/div
12 cm CD Eject operation
Ref.: GND
C
Mode: Normal
500 s/div
12 cm CD Eject operation
8 cm CD Eject operation
*DP (DM
1 V/div 1 V/div
50 ns/div
*DP (DM
2 V/div 2 V/div
50 ms/div
*DP (DM
2 V/div 2 V/div
50 ms/div
USB Play
DEH-4000UB/XS/EW5
5 6 7 8
61
*DP (DM
2 V/div 2 V/div
50 ms/div
62
DEH-4000UB/XS/EW5
1 2 3 4
DEH-4000UB/XS/EW5
5 6 7 8
63
CORD ASSY
16
140
CN901
Connector
B
Capacitor
SIDE A 130
P.C.Board Chip Part
15
C313
SIDE B
IC921
120
1
C923 D901
110
Q911 D552 L901 D903 D971 R955
D9
100
D904
D551
L951
90
D911
80
Q702
70
C911
L101
CN251
1
60
D502 C502
CN701
15
50
C
CN701
E
L501
40
5
10
30
C501
C708
20
BZ601 L852
B
CN1801
F
CN803
10
10
A
64
1 2
10
20
30
40
50
60
70
DEH-4000UB/XS/EW5
3 4
SIDE A
SSY
1
2 IC301 10 10 20 1 5 1 1 5 C311 C451 15 25
CN351
RCA
B
ANTENNA
CN401
D901 R454 D902 D454 D971 R955 C355 L161 D551 L951 C971 C351C352 C165 C353 C354 C356 C405 Y401 R309
L401 C162
C160
10
C183 L101 D181
CN622
15
C401
X601 L601
20
C962
10
C842
FRONT
70 80 90 100 110 120 130 140 150 160 170
A
8
DEH-4000UB/XS/EW5
5 6 7
65
R364
R393
C362
R382 R383
Q353
R355
R381
R363
B
1
C357 C358
1
R452 Q451
R451
E
C317
R352
R301 C308 C307 R304 R302 R306 R353 R303 C303 R307 L402 R308 C304 C302 R354 C301 R305 R953
Q453
R954
D951
Q951
R951 R952
C
C406 R407 R406 R405 R404 R421 R403
R356
R180
C411
15
10
20
C163 C705
R603
IC151
R402
R412
C152 C154
25
C156
C153 C155
C182
C159
PCL
R612
C407
C704
R181
Q182
TEST
55 60
50 45 40 35
R113
65
R607
70
R605 C402
30
IC601
75
R401
15
R619 R409
80
20
25
R410
R411 R415 Q401 R834 C179 C403 R413 R178 R177 C176 R173 R174 IC401 C175 IC171 C173 R841 R842 Q842 D172 R175 C178 R176 Q171 R171 C171 R172 Q172
R609 R608
C604
R962
R606
R833 R804
C410
C404
Q841 R809 R816 R803 R845 R824 R835 R819 Q844 R844 C841 D
Q843
A
66
1
170
160
150
140
130
120
110
100
DEH-4000UB/XS/EW5
2 3 4
10
R831 R829
95
Q402
R408
90
R837 R830
10
85
1 E
R604
R507
C602
1 1 1 5 1 E E
90
SIDE B 150
R633 R625 C622 R624 R621 C621 R626 C103 C102 R105 R117 R104 R116 1 1 R103 R971 R938 R108 R101 R106 R109 C931 C901 R937 Q102 R102 R107 C101 1 R622 R629 R628 R623
140
130
120
E
C924 C921 R111 R922
110
100
E
Q101 R110
10
1
C551 Q971 IC551
5
R118 R112
90
80
C912 Q912
PCL
45 40 35
R113
R254
R911
C251
70
D
Q701
C721
30
R114
25
R507
R618 L251
D251 R253 C701 C504 C702 R708 R706 R705 R710 R846 R847 R703 R712 R711 R509 R510 C507 D501
60
20
15
R714
C720
R256 R255
10
R848
50
C602
R808 R813 R811 R815 R967 R814 R805 C715 C716 R508 C506 IC501
40
1
C707
R505
C505
IC702
30
1
R512
R849 R807 R806 R819 D809 1 D806 D805 D803 D801 D810 D802 D807 R832 Q851 R851
R852 Q852
20
C851
10
D808 D804
Y
50 40 30 20 10 0
90
80
70
60
X
7 8
A
67
DEH-4000UB/XS/EW5
5 6
68
B
B
KEYBOARD UNIT
LIST RPT/LOCAL EJECT USB MULTI-CONTROL RDM
DEH-4000UB/XS/EW5
SRC/OFF
DISP/BACK/SCRL
BAND/ESC
3
SIDE A
KEYBOARD UNIT
SIDE B
A
CN803
B
DEH-4000UB/XS/EW5
5 6 7 8
69
CD CORE UNIT(S10.5COMP2-USB)
SIDE A
PICKUP UNIT(P10.5)(SERVICE)
CN701
REFO1 E F
HOME
LOADING/CARRIAGE MOTOR
M M
SPINDLE MOTOR
C
70 DEH-4000UB/XS/EW5
1 2 3 4
CD CORE UNIT(S10.5COMP2-USB)
SIDE B
8EJ 12EJ
DSCSNS
C
DEH-4000UB/XS/EW5
5 6 7 8
71
NOTE: Parts whose parts numbers are omitted are subject to being not supplied. The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Meaning of the figures and others in the parentheses in the parts list. Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No. Circuit Symbol and No.
Q 402 Q 451 Q Q Q Q Q Q Q Q Q Q 453 701 702 841 842 851 852 911 912 931
Part No.
Unit Number : YWM5203(EW5) Unit Number : YWM5205(ES) Unit Number : YWM5207(CN5) Unit Name : Tuner Amp Unit Unit Number : (EW5) Unit Number : (ES) Unit Name : Keyboard Unit Unit Number : (CN5) Unit Name : Keyboard Unit Unit Number : CWX3527 Unit Name : CD Core Unit(S10.5COMP2-USB)
(B,156,45) Transistor(EW5) UMH1N (B,117,119) Transistor RT1N241M (B,116,116) Transistor (B,20,60) Transistor (A,7,70) Transistor (B,131,23) Transistor (B,139,17) Transistor (B,33,15) (B,24,16) (A,7,104) (B,16,73) (B,64,94) (B,64,94) RT3T22M RT3T22M 2SD2396 2SA1036K RT1N141M-11
Transistor 2SA1036K Transistor RT1N141M-11 Transistor 2SD2396 Transistor RT3T22M Transistor(EW5,ES) RT3CLLM Transistor(CN5) UMX1N
Q D D D D D D D D D D D D D D D D D D D D D D D D
951 454 501 502 621 622 623 701 801 802 803 804 805 806 809 810 901 902 903 904 911 912 931 932 951
(B,112,106) Transistor(EW5) 2SA1037K (A,94,105) Diode 1SS133 (B,22,44) Diode RB060L-40 (A,16,58) Diode S5688G (B,111,90) Varistor EZJZ1V270RM (B,111,94) Varistor (B,111,91) Varistor (A,26,65) Diode (B,63,6) Varistor (B,64,6) Varistor (B,68,6) Varistor (B,69,6) Varistor (B,74,6) Varistor (B,78,6) Varistor (B,80,14) Varistor (B,60,6) Varistor (A,74,110) Diode (A,78,107) Diode (A,62,103) Diode (A,59,103) Diode (A,16,80) Diode (A,16,75) Diode (A,55,96) Diode (A,54,93) Diode (B,108,109) Diode(EW5) EZJZ1V270RM EZJZ1V270RM HZS7L(C3) EZJZ1V270RM EZJZ1V270RM EZJZ1V270RM EZJZ1V270RM EZJZ1V270RM EZJZ1V270RM EZJZ1V270RM EZJZ1V270RM S5688G S5688G S5688G S5688G S5688G HZS6L(B2) HZS7L(C3) HZS7L(A1) MC2848-11
MISCELLANEOUS
IC 151 IC 251 IC 301 IC 401 IC 501 IC 601 IC 702 IC 921 IC 961 Q 351 Q 353 Q 401 (B,135,85) IC (B,44,69) IC (A,105,139) IC (B,165,29) IC (B,16,32) Regulator IC (B,96,57) (B,96,57) (B,58,29) (A,6,120) (B,98,33) IC(EW5) IC(ES,CN5) IC IC IC PML018A R5523N001B PAL007C NJM2885DL1-33 BD9781HFP PEG475A PEG409A NJM2885DL1-33 NJM2388F84 S-80835CNMC-B8U
(B,165,113) Surge Protector IMSA-6801-01Y901 (A,122,99) Inductor LAU2R2K (A,150,90) Inductor LAU1R0K
72
DEH-4000UB/XS/EW5
3 4
Part No.
LCTAW220J2520 LAU1R0K
Part No.
RS1/16S153J RD1/4PU102J RS1/16S3302F RS1/16S333J RS1/16S8201F RS1/16S683J RS1/16S222J RS1/16S823J RS1/10SR471J RS1/16S0R0J RS1/16S222J RS1/16S103J RS1/16S103J RS1/16S681J RS1/16S681J RS1/16S103J RS1/16S681J RS1/16S104J RS1/16S104J RS1/16S473J RS1/16S104J RS1/16S473J RS1/16S473J RS1/16S102J RS1/16S0R0J RS1/16S0R0J RS1/16S102J RS1/16S102J RS1/16S223J RS1/16S223J RS1/16S102J RS1/16S104J RS1/16S104J RS1/16S101J RS1/16S101J RS1/16S0R0J RD1/4PU271J RS1/16S472J RS1/16S104J RS1/16S472J RS1/16S104J RS1/16S104J RS1/16S221J RS1/16S102J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S104J RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S104J RS1/16S473J RS1/16S104J RS1/16S102J RS1/16S102J RS1/16S1R0J RS1/16S102J
8 A
(A,29,40) Inductor YTF5003 (A,94,41) Ferri-Inductor LAU100K (A,104,34) Inductor LAU2R2K (A,37,16) Inductor LAU2R2K (A,39,102) Choke Coil 600 H CTH1280 (A,70,103) Inductor(EW5) LAU2R2K (A,84,44) Oscillator 15 MHz YSS5002 (B,131,132) Fuse 3 A CEK1286 (A,29,16) Buzzer(ES,CN5) CPV1062 (A,163,101) FM/AM Tuner Unit(EW5) CWE2097 (A,163,101) FM/AM Tuner Unit(ES,CN5) CWE2098 Fuse 10 A YEK5001
>
RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 151 152 153 180 254 257 301 303 304 306 309 351 352 355 356 358 359 360 363 364 381 382 384 393 394 401 402 403 404 405 (B,146,88) (B,147,87) (B,145,86) (B,120,97) (B,45,72) (B,58,52) (B,124,111) (B,128,109) (B,140,109) (B,134,109) (A,98,106) (B,159,114) (B,156,120) (B,136,121) (ES,CN5) (B,132,97) (B,131,129) (ES,CN5) (B,163,133) (B,159,132) (B,134,129) (ES,CN5) (B,137,129) (ES,CN5) (B,136,129) (ES,CN5) (B,140,125) (ES,CN5) (B,148,117) (B,141,128) (ES,CN5) (B,144,128) (B,152,54) (B,158,78) (EW5) (B,156,85) (B,157,88) (B,157,90) (B,156,91) (B,156,93) (B,156,93) (B,142,46) (B,147,49) (B,147,46) (B,142,43) (B,156,36) (A,157,23) (B,156,42) (B,155,86) (B,121,117) (B,119,121) RS1/16S102J RS1/16S102J RS1/16S102J RS1/16S0R0J RS1/16S681J RS1/16S103J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J RD1/4PU153J RS1/16S821J RS1/16S0R0J RS1/16S821J RS1/16S821J RS1/16S821J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S102J RS1/16S0R0J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S221J RD1/4PU4R7J RS1/16S221J RS1/16S0R0J RS1/16S103J RS1/16S221J
DEH-4000UB/XS/EW5
5 6
73
Part No.
RS1/16S0R0J RS1/16S0R0J RS1/16S103J RS1/16S472J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S103J RS1/16S153J RS1/16S472J RS1/16S222J RS1/16S223J RD1/4PU152J RS1/16S473J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S472J RS1/4SA102J RS1/16S473J RS1/16S102J RS1/16S472J RD1/4PU153J RS1/16S822J RS1/16S102J C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
Part No.
CKSRYB103K50 CKSYB475K10 CEJQ101M10 CKSRYB104K25 CKSRYB103K50 CEJQ220M10 CKSRYB474K10 CCSRCH470J50 CKSRYB105K10 CEJQ330M10 CCH1781 CEJQ221M16 CCSRCH221J50 CKSRYB105K16 CCSRCH101J50 CKSRYB332K50 CKSRYB104K25 CKSRYB105K10 CCSRCH180J50 CCSRCH180J50 CKSRYB105K10 CEJQ100M16 CKSRYB104K25 CEJQ100M16 CCSRCH470J50 CKSRYB472K50 CKSRYB472K50 CKSRYB104K25 CKSRYB473K25 CEJQ101M10 CKSRYB105K10 CKSRYB105K10 CEJQ220M10 CKSRYB105K10 CKSRYB474K10 CKSRYB105K10 CKSRYB104K25 CKSRYB104K25 CEJQ470M10 CKSRYB103K50 CEAT102M16 CKSRYB103K50 CEJQ221M10 CEJQ101M16 CKSRYB103K50 CKSRYB473K25 CEJQ100M16
(B,44,11) (B,109,48) (B,134,23) (B,135,23) (B,58,44) (B,59,42) (B,58,50) (B,45,20) (B,34,19) (B,24,19) (B,44,8) (B,20,71) (A,16,78) (B,11,110) (B,82,50) (B,113,78) (B,64,96) (B,64,98) (B,61,91) (B,60,98) (B,63,117) (B,59,125) (B,106,106) (B,106,104) (EW5) (B,115,107) (EW5) (A,73,103) (EW5) (B,102,32) (B,90,36)
R R R R R R R R R R R
841 842 846 847 848 849 851 852 853 911 912 922 931 932 933 934 935 936 937 938 951 952 953 955 962 967
R R R R R R R R R R R R R R R
CAPACITORS
C C C C C
D
153 154 155 156 159 160 162 163 165 251 252 253 305 306 307 308 309 310 311 313 315 316 317 318 351 352 355 356 401 402
(B,159,74) (B,145,78) (B,163,71) (B,119,80) (B,119,79) (A,124,83) (A,124,89) (B,124,86) (A,135,97) (B,50,68) (B,44,63) (B,42,65) (B,135,113) (B,127,113) (B,129,113) (B,132,113) (B,125,134) (B,127,132) (A,103,127) (A,51,123) 3 300 F/16 V (B,134,117) (B,125,114) (B,123,114) (B,131,117) (A,130,97) (A,141,97) (A,130,103) (ES,CN5) (A,147,103) (ES,CN5) (A,155,55) (B,158,56)
CKSRYB224K10 CKSRYB105K10 CKSRYB224K10 CKSRYB105K10 CKSRYB105K10 CEJQ100M16 CEJQ470M10 CKSRYB104K25 CEJQ100M16 CKSRYB104K25 CKSRYB104K25 CKSRYB103K50 CKSQYB474K25 CKSQYB474K25 CKSQYB474K25 CKSQYB474K25 CKSQYB225K10 CKSQYB225K10 CEJQ100M16 CCH1494 CKSRYB474K10 CKSRYB474K10 CKSRYB474K10 CKSRYB474K10 CEJQ2R2M50 CEJQ2R2M50 CEJQ2R2M50 CEJQ2R2M50 CEJQ470M6R3 CKSRYB103K50
C C C C C C C C C C
C C C C C C C C C C C C C C C
C 961 C 962
74
DEH-4000UB/XS/EW5
1 2 3 4
Part No.
NESW505C-5273 EZJZ1V800AM EZJZ1V800AM SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT SML-310VT
Part No.
MISCELLANEOUS
IC 1801 IC 1802 D 1801 D 1802 D 1803 D D D D D D D D D D D D D D D D D L X S S S S S S S S S S S 1805 1806 1807 1808 1809 1810 1811 1812 1813 1814 1815 1816 1817 1818 1819 1823 1824 1801 1801 1801 1802 1803 1804 1805 1806 1807 1808 1809 1810 1827 (B,30,113) (A,30,161) (B,32,149) (B,32,146) (A,26,156) IC Remote IC Diode Diode White LED PD6538A GP1UX51RK MC2848-11 MC2846-11 NESW505C-5273 SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT SML-310PT
(A,15,30) LED (A,15,8) LED (A,5,7) LED (A,39,9) LED (A,36,17) LED (A,28,12) (A,17,56) (A,6,144) (A,5,162) (A,37,56) (A,34,36) (A,39,27) (A,18,38) (A,17,17) (A,28,26) LED LED LED LED LED LED LED LED LED LED
(A,18,17) LED SML-310VT (A,26,26) LED SML-310VT (B,11,151) Inductor CTF1713 (B,40,124) Ceramic Resonator 5.00 MHz CSS1547 (A,8,161) Push Switch CSG1155 (A,18,8) Push Switch (A,15,35) Push Switch (A,36,8) Push Switch (A,8,7) Push Switch (A,18,28) Push Switch (A,39,60) (A,36,28) (A,15,60) (A,39,35) (A,27,47) CSG1155 CSG1155 CSG1155 CSG1155 CSG1155
Push Switch CSG1155 Push Switch CSG1155 Push Switch CSG1155 Push Switch CSG1155 Switch (MULTI-CONTROL) CSX1120 YAW5091
(B,12,148) Varistor EZJZ1V800AM (B,11,148) Varistor EZJZ1V800AM (B,11,151) Inductor CTF1713 (B,40,124) Ceramic Resonator 5.00 MHz CSS1547 (A,8,161) Push Switch CSG1155 (A,18,8) Push Switch (A,15,35) Push Switch (A,36,8) Push Switch (A,8,7) Push Switch (A,18,28) Push Switch (A,39,60) (A,36,28) (A,15,60) (A,39,35) (A,27,47) CSG1155 CSG1155 CSG1155 CSG1155 CSG1155
LCD1801
(A,18,69) LCD
RESISTORS
R R R R R R R R R R R R R R R R R R 1801 1802 1803 1812 1813 1814 1815 1817 1822 1823 1824 1825 1831 1832 1833 1834 1835 1838 (B,29,74) (B,30,74) (B,26,150) (B,12,14) (B,28,10) (B,8,150) (B,25,19) (B,18,20) (B,35,38) (B,37,38) (B,37,40) (B,37,41) (B,35,41) (B,36,143) (ES) (B,40,144) (ES) (B,38,144) (EW5) (B,36,145) (ES) (B,30,33) RS1/16S222J RS1/16S222J RS1/4SA152J RS1/4SA561J RS1/4SA561J RS1/4SA561J RS1/4SA561J RS1/4SA561J RS1/16S222J RS1/16S332J RS1/16S822J RS1/16S333J RS1/16S473J RS1/16S103J RS1/16S2R2J RS1/16S104J RS1/16S121J RS1/16S0R0J
Push Switch CSG1155 Push Switch CSG1155 Push Switch CSG1155 Push Switch CSG1155 Switch (MULTI-CONTROL) CSX1120 YAW5091
LCD1801
(A,18,69) LCD
RESISTORS
R R R R R R R R R R R R R R 1801 1802 1803 1804 1805 1806 1807 1809 1822 1823 1824 1825 1831 1832 (B,29,74) (B,30,74) (B,26,150) (B,12,11) (B,28,8) (B,5,150) (B,28,20) (B,21,21) (B,35,38) (B,37,38) (B,37,40) (B,37,41) (B,35,41) (B,36,143) (B,40,144)
7
RS1/16S222J RS1/16S222J RS1/4SA561J RS1/4SA471J RS1/4SA471J RS1/4SA471J RS1/4SA471J RS1/4SA471J RS1/16S222J RS1/16S332J RS1/16S822J RS1/16S333J RS1/16S473J RS1/16S103J RS1/16S2R2J
8
CAPACITORS
C C C C 1801 1802 1803 1804 (B,38,141) (ES) (B,34,140) (B,32,140) (B,31,140) CKSYF106Z10 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25
R 1833
DEH-4000UB/XS/EW5
5 6
75
Part No.
RS1/16S121J RS1/16S0R0J
Part No.
RS1/16SS104J RS1/16SS104J RS1/16SS0R0J RS1/16SS104J RS1/16SS0R0J RS1/16SS0R0J RS1/16SS103J RS1/16SS240J RS1/16SS240J RS1/16SS153J RS1/16SS153J RS1/16SS103J RS1/16SS272J RS1/16SS471J RS1/16SS183J RS1/16SS183J RS1/16SS183J RS1/16SS183J RS1/16SS0R0J RS1/16SS0R0J RS1/16S0R0J RS1/16SS221J RS1/16SS221J RS1/16S0R0J RS1/16SS0R0J RS1/16SS0R0J
(B,36,145) (B,41,18)
CAPACITORS
C C C C 1801 1802 1803 1804 (B,38,141) (B,34,140) (B,32,140) (B,31,140) CKSYF106Z10 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25
MISCELLANEOUS
IC 201 IC 301 Q 101 Q 102 X 201 X S S S S 205 901 903 904 905 (A,36,46) IC PE5611B (A,29,15) IC BA5839FP (B,58,70) Transistor 2SA1577 (B,49,58) Chip Transistor 2SB1689 (A,23,38) Ceramic Resonator 16.934 MHz CSS1603 (B,34,63) (A,55,37) (B,20,59) (B,41,68) (B,25,70) Oscillator 48.000 MHz CSS1753 Switch(HOME) CSN1067 Switch(DSCSNS) CSN1067 Switch(12EJ) CSN1068 Switch(8EJ) CSN1068
RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 101 102 103 104 105 107 202 203 204 206 209 210 214 216 221 222 223 225 226 227 228 229 230 232 233 234 235 237 240 241 (B,61,74) (B,61,72) (B,61,71) (B,54,67) (B,45,58) (B,52,60) (A,27,33) (A,51,44) (A,24,58) (B,10,27) (B,19,53) (B,10,23) (B,50,50) (B,49,49) (A,51,48) (A,51,46) (B,14,43) (A,51,50) (A,51,51) (B,48,52) (B,45,52) (B,47,54) (B,22,25) (B,46,52) (B,26,59) (B,23,26) (A,26,59) (A,24,35) (B,14,26) (B,14,25) (B,22,55) (A,26,64) RS1/10SR2R4J RS1/10SR2R4J RS1/10SR2R7J RS1/16SS222J RS1/16SS102J RS1/16SS105J RS1/16SS473J RS1/16S473J RS1/16SS221J RS1/16SS104J RS1/16SS103J RS1/16SS102J RS1/16SS472J RS1/16SS472J RS1/16SS103J RS1/16SS103J RS1/16SS473J RS1/16SS103J RS1/16SS393J RS1/16SS562J RS1/16SS122J RS1/16SS472J RS1/16SS0R0J RS1/16SS122J RS1/16SS103J RS1/16SS473J RS1/16SS473J RS1/16SS151J RS1/16S473J RS1/16SS103J RS1/16SS473J RS1/16SS104J
CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 106 202 204 205 206 207 209 210 211 212 213 214 216 217 218 219 220 221 222 223 224 226 227 228 229 236 239 240 243 250 (B,57,67) (A,28,57) (A,24,59) (B,27,41) (A,23,41) (A,25,38) (B,36,35) (B,29,37) (A,28,35) (A,29,30) (A,46,39) (A,29,34) (A,51,52) (A,48,52) (A,50,52) (A,47,54) (A,48,54) (A,46,54) (B,46,54) (B,48,54) (A,45,56) (A,42,59) (A,42,61) (B,41,62) (B,48,60) (A,50,58) (B,47,52) (A,38,61) (B,22,41) (A,52,48) (A,52,46) CKSQYB475K6R3 CKSSYB104K10 CKSSYB103K16 CKSQYB475K6R3 CKSSYB104K10 CKSRYB104K16 CEVW220M6R3 CKSSYB104K10 CKSSYB104K10 CKSRYB104K16 CKSSYB104K10 CKSSYB104K10 CKSSYB332K50 CKSSYB104K10 CKSSYB473K10 CKSSYB104K10 CKSSYB182K50 CKSSYB104K10 CCSSCH560J50 CCSSCH4R0C50 CKSSYB104K10 CCSSCH680J50 CCSSCH470J50 CKSSYB103K16 CKSSYB104K10 CKSSYB104K10 CCSSCH220J50 CKSSYB104K10 CKSQYB475K6R3 CKSSYB102K50 CKSSYB102K50
R 244 R 254
C 251
76
DEH-4000UB/XS/EW5
1 2 3 4
Part No.
CKSSYB104K10 CCSSCH8R0D50 CCSSCH8R0D50 CKSSYB102K50 CKSSYB472K25 CKSSYB223K16 CKSRYB104K16 CKSRYB105K10 CCSSCH101J50 CKSSYB102K50 CKSSYB104K10
C 704 C 711
DEH-4000UB/XS/EW5
5 6 7 8
77