Pioneer Deh 2100ub 2110ub 2120ub

ORDER NO.
CRT4227
DEH-2100UB/XS/EW5
CD RDS RECEIVER
DEH-2100UB
DEH-2120UB/XS/EW5 DEH-2110UB/XS/UR
Model No.
CX-3240
/XS/EW5
This service manual should be used together with the following manual(s):
Order No.
CRT4050
Mech.Module
S10.5COMP2-iPod/USB
Remarks
CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
For details, refer to "Important Check Points for Good Servicing".
PIONEER CORPORATION
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA)
INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 10
87, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LT
D. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2008
K-ZZZ. OCT. 2008 Printed in Japan
1
2
3
4
SAFETY INFORMATION
A
This service manual is intended for qualified service technicians; it is not mea
nt for the casual do-it-yourselfer. Qualified technicians have the necessary tes
t equipment and tools, and have been trained to properly and safety repair compl
ex products such as those covered by this manual. Improperly performed repairs c
an adversely affect the safety and reliability of the product and may void the w
arranty. If you are not qualified to perform the repair of this product properly
and safety, you should not risk trying to do so and refer the repair to a quali
fied service technician.
Where in a manufacturer’s service documentation, for example in circuit diagrams o
r lists of components, a symbol is used to indicate that a specific component sh
all be replaced only by the component specified in that documentation for safety
reasons, the following symbol shall be used:
B
- Safety Precautions for those who Service this Unit. When checking or adjusting
the emitting power of the laser diode exercise caution in order to get safe, re
liable results. Caution: 1. During repair or tests, minimum distance of 13 cm fr
om the focus lens must be kept. 2. During repair or tests, do not view laser bea
m for 10 seconds or longer.
CAUTION:
C
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPE
CIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS
WARNING!
D
The AEL (accessible emission level) of the laser power output is less than CLASS
1 but the laser component is capable of emitting radiation exceeding the limit
for CLASS 1. A specially instructed person should do servicing operation of the
apparatus.
Laser diode characteristics
Wave length : 785 nm to 814 nm Maximum output : 1 190 µW(Emitting period : unlimit
ed)
E
Additional Laser Caution
Transistors Q101 in PCB drive the laser diodes. When Q101 is shorted between the
ir terminals, the laser diodes will radiate beam. If the top cover is removed wi
th no disc loaded while such short-circuit is continued, the naked eyes may be e
xposed to the laser beam.
F
2
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with
the below symbol. Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations)
, and maintain a safe servicing environment by following the safety instructions
described in this manual. 1 Use specified parts for repair. Use genuine parts.
Be sure to use important parts for safety. 2 Do not perform modifications withou
t proper instructions. Please follow the specified safety methods when modificat
ion(addition/change of parts) is required due to interferences such as radio/TV
interference and foreign noise. 3 Make sure the soldering of repaired locations
is properly performed. When you solder while repairing, please be sure that ther
e are no cold solder and other debris. Soldering should be finished with the pro
per quantity. (Refer to the example) 4 Make sure the screws are tightly fastened
. Please be sure that all screws are fastened, and that there are no loose screw
s. 5 Make sure each connectors are correctly inserted. Please be sure that all c
onnectors are inserted, and that there are no imperfect insertion. 6 Make sure t
he wiring cables are set to their original state. Please replace the wiring and
cables to the original state after repairs. In addition, be sure that there are
no pinched wires, etc. 7 Make sure screws and soldering scraps do not remain ins
ide the product. Please check that neither solder debris nor screws remain insid
e the product. 8 There should be no semi-broken wires, scratches, melting, etc.
on the coating of the power cord. Damaged power cords may lead to fire accidents
, so please be sure that there are no damages. If you find a damaged power cord,
please exchange it with a suitable one. 9 There should be no spark traces or si
milar marks on the power plug. When spark traces or similar marks are found on t
he power supply plug, please check the connection and advise on secure connectio
ns and suitable usage. Please exchange the power cord if necessary. a Safe envir
onment should be secured during servicing. When you perform repairs, please pay
attention to static electricity, furniture, household articles, etc. in order to
prevent injuries. Please pay attention to your surroundings and repair safely.
A
B
C
D
2. Adjustments
To keep the original performance of the products, optimum adjustments and confir
mation of characteristics within specification. Adjustments should be performed
in accordance with the procedures/instructions described in this manual.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance. Make sure th
e proper amount is applied.
E
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lense
s and mirrors used in projection monitors, proper cleaning should be performed t
o restore their performances.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode s
hould be set or the shipping screws should be installed before shipment. Please
be sure to follow this method especially if it is specified in this manual.
F
DEH-2100UB/XS/EW5
5 6 7 8
3
1
2
3
4
CONTENTS
A
B
C
D
SAFETY INFORMATION .............................................................
........................................................................ 2 1. SE
RVICE PRECAUTIONS ..............................................................
................................................................. 5 1.1 SERVICE
PRECAUTIONS.....................................................................
.................................................... 5 1.2 NOTES ON SOLDERING ..
................................................................................
........................................ 5 2. SPECIFICATIONS ...................
................................................................................
......................................... 6 2.1 SPECIFICATIONS..................
................................................................................
.................................... 6 2.2 DISC/CONTENT FORMAT .................
................................................................................
....................... 8 2.3 PANEL FACILITIES .................................
................................................................................
................... 9 2.4 CONNECTION DIAGRAM ...................................
................................................................................
.... 12 3. BASIC ITEMS FOR SERVICE..............................................
.......................................................................... 13 3.
1 CHECK POINTS AFTER SERVICING..................................................
................................................... 13 3.2 PCB LOCATIONS .......
................................................................................
............................................. 14 3.3 JIGS LIST .................
................................................................................
............................................... 15 3.4 CLEANING.................
................................................................................
.............................................. 15 4. BLOCK DIAGRAM..............
................................................................................
............................................ 16 5. DIAGNOSIS....................
................................................................................
................................................ 19 5.1 OPERATIONAL FLOWCHART ..
................................................................................
.............................. 19 5.2 ERROR CODE LIST ..........................
................................................................................
...................... 20 5.3 CONNECTOR FUNCTION DESCRIPTION ...................
.......................................................................... 22 6.
SERVICE MODE ..................................................................
.......................................................................... 23 6.
1 DISPLAY TEST MODE ............................................................
................................................................ 23 6.2 CD TEST
MODE ...........................................................................
........................................................... 24 7. DISASSEMBLY...
................................................................................
............................................................ 25 8. EACH SETTING
AND ADJUSTMENT .................................................................
.......................................... 28 8.1 CD ADJUSTMENT.................
................................................................................
.................................. 28 8.2 CHECKING THE GRATING AFTER CHANGING TH
E PICKUP UNIT.................................................... 29 9. EXPLODED
VIEWS AND PARTS LIST...........................................................
............................................... 32 9.1 PACKING .................
................................................................................
................................................ 32 9.2 EXTERIOR (1) ...........
................................................................................
.............................................. 34 9.3 EXTERIOR (2) .............
................................................................................
............................................ 36 9.4 CD MECHANISM MODULE.........
................................................................................
............................ 38 10. SCHEMATIC DIAGRAM ..........................
................................................................................
..................... 40 10.1 TUNER AMP UNIT(GUIDE PAGE) .......................
................................................................................
. 40 10.2 KEYBOARD UNIT.........................................................
......................................................................... 46 10.
3 CD MECHANISM MODULE(GUIDE PAGE) ..............................................
............................................ 48 10.4 WAVEFORMS .................
................................................................................
....................................... 54 11. PCB CONNECTION DIAGRAM ..........
................................................................................
......................... 58 11.1 TUNER AMP UNIT................................
................................................................................
................. 58 11.2 KEYBOARD UNIT.........................................
................................................................................
......... 62 11.3 CD CORE UNIT(S10.5COMP2-USB-C3) ..............................
................................................................ 64 12. ELECTRIC
AL PARTS LIST ..................................................................
........................................................ 66
E
F
4
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A
1. You should conform to the regulations governing the product (safety, radio an
d noise, and other regulations), and should keep the safety during servicing by
following the safety instructions described in this manual. 2. Before disassembl
ing the unit, be sure to turn off the power. Unplugging and plugging the connect
ors during power-on mode may damage the ICs inside the unit. 3. To protect the p
ickup unit from electrostatic discharge during servicing, take an appropriate tr
eatment (shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing
the pickup unit, be sure to check the grating. 5. Be careful in handling ICs. So
me ICs such as MOS type are so fragile that they can be damaged by electrostatic
induction.
B
C
1.2 NOTES ON SOLDERING
D
For environmental protection, lead-free solder is used on the printed circuit bo
ards mounted in this unit. Be sure to use lead-free solder and a soldering iron
that can meet specifications for use with lead-free solders for repairs accompan
ied by reworking of soldering. Compared with conventional eutectic solders, lead
-free solders have higher melting points, by approximately 40 C. Therefore, for
lead-free soldering, the tip temperature of a soldering iron must be set to arou
nd 373 C in general, although the temperature depends on the heat capacity of th
e PC board on which reworking is required and the weight of the tip of the solde
ring iron. Compared with eutectic solders, lead-free solders have higher bond st
rengths but slower wetting times and higher melting temperatures (hard to melt/e
asy to harden). The following lead-free solders are available as service parts:
Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP10
08 0.3 in dia.
E
F
DEH-2100UB/XS/EW5
5 6 7 8
5
1
2
3
4
2. SPECIFICATIONS
2.1 SPECIFICATIONS
A
DEH-2100UB/XS/EW5, DEH-2120UB/XS/EW5
General
Power source..........................14.4 V DC (10.8 V to 15.1 V allowable) Gro
unding system.................Negative type Max. current consumption ...........
....................................10.0 A Backup current ......................
... 2 mA or less Dimensions (W × H × D): DIN Chassis .................. 178 mm × 50 mm
× 165 mm Nose ....................... 188 mm × 58 mm × 15 mm D Chassis ..............
.... 178 mm × 50 mm × 165 mm Nose ....................... 170 mm × 48 mm × 15 mm Weight
..................................... 1.3 kg
C
B
Maximum amount of memory .............................................. 250 GB M
inimum amount of memory .............................................. 256 MB US
B Class.............................. MSC (Mass Storage Class) File system......
....................... FAT16, FAT32 MP3 decoding format ......... MPEG-1 & 2 Au
dio Layer 3 WMA decoding format ....... Ver. 7, 7.1, 8, 9, 10, 11 (2ch audio) (W
indows Media Player) WAV signal format ............... Linear PCM & MS ADPCM (No
n-compressed)
FM tuner
Frequency range................... 87.5 MHz to 108.0 MHz Usable sensitivity.....
............. 11 dBf (0.7 μV/75 , mono, S/N: 30 dB) Signal-to-noise ratio.........
.... 72 dB (IEC-A network)
Audio
Maximum power output ...... 50 W × 4 Continuous power output .. 22 W × 4 (50 Hz to 1
5 000 Hz, 5% THD, 4 load, both channels driven) Load impedance .................
.. 4 (4 to 8 allowable) Preout max output level ...... 2.0 V Tone controls: Bass
Frequency............. 100 Hz Gain ........................ ±13 dB Mid Frequency.
............. 1 kHz Gain ......................... ±12 dB Treble Frequency........
...... 10 kHz Gain ......................... ±12 dB
MW tuner
Frequency range................... 531 kHz to 1 602 kHz Usable sensitivity......
............ 25 μV (S/N: 20 dB) Signal-to-noise ratio............. 62 dB (IEC-A ne
twork)
LW tuner
Frequency range................... 153 kHz to 281 kHz Usable sensitivity........
.......... 28 μV (S/N: 20 dB) Signal-to-noise ratio............. 62 dB (IEC-A netw
ork)
D
Note Specifications and the design are subject to modifications without notice d
ue to improvements.
CD player
System ..................................... Compact disc audio system Usable di
scs .......................... Compact disc Signal-to-noise ratio............. 9
4 dB (1 kHz) (IEC-A network) Number of channels ............ 2 (stereo) MP3 deco
ding format ......... MPEG-1 & 2 Audio Layer 3 WMA decoding format ....... Ver.
7, 7.1, 8, 9, 10, 11 (2ch audio) (Windows Media Player) WAV signal format ......
.......... Linear PCM & MS ADPCM (Non-compressed)
E
USB
F
Specification ......................... USB 2.0 full speed Supply current ......
............... 500 mA
6
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
DEH-2110UB/XS/UR
A
B
C
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
7
1
2
3
4
A
B
C
2.2 DISC/CONTENT FORMAT
D
E
F
8
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
2.3 PANEL FACILITIES
What ’s what
Head unit
3 12 45 6 7
8
(detach) button Press to remove the front panel from the head unit.
A
9 AUX input jack (3.5 mm stereo jack) Use to connect an auxiliary device. a 1 to
6 buttons Press for preset tuning. Also used for controlling functions. • 1/S.Rtr
vcan be used to control S.RTRV (sound retriever). • 2/PAUSE can be used to control
PAUSE (pause). • 5/ can be used to control RANDOM (random). • 6/ can be used to con
trol REPEAT(repeat). b / / / buttons Press to perform manual seek tuning, fast f
orward, reverse and track search controls. Also used for controlling functions. •
When operating menus — Pressing is the same function as turning MULTI-CONTROL righ
t. — Pressing is the same function as turning MULTI-CONTROL left. — Pressing is the
same function as pressing DISP/BACK/SCRL . — Pressing and holding is the same func
tion as pressing and holding DISP/BACK/SCRL . — Pressing is the same function as p
ressing MULTI-CONTROL . — Pressing and holding is the same function as pressing an
d holding MULTI-CONTROL . • When operating lists — Pressing is the same function as
turning MULTI-CONTROL left. — Pressing is the same function as turning MULTI-CONTR
OL right. — Pressing is the same function as pressing DISP/BACK/SCRL .
B
dc b
a
98
1 SRC/OFF button This unit is turned on by selecting a source. Press to cycle th
rough all the available sources. 2 /LIST button Press to display the disc title
list, track title list, folder list or file list.
C
3 MULTI-CONTROL Turn to increase or decrease the volume. Also used for controlli
ng functions. 4 TA/AF button Press to turn TA function on or off. Press and hold
to turn AF function on or off. 5 Disc loading slot Insert a disc to play. 6 (ej
ect) button Press to eject a disc.
D
7 USB port Use to connect a USB audio player/USB memory. • When connecting, open u
p the USB connector lid. • Use a USB cable to connect the USB audio player/USB mem
ory to the USB port. Since the USB audio player/USB memory is projected forward
from the unit, it is dangerous to connect directly. Pioneer CD-U50E USB cable is
also available. For details, consult your dealer.
E
F
DEH-2100UB/XS/EW5
5 6 7 8
9
1
2
3
4
A
— Pressing and holding is the same function as pressing and holding DISP/BACK/SCRL
. — Pressing is the same function as pressing MULTI-CONTROL . — Pressing and holdin
g is the same function as pressing and holding MULTI-CONTROL . c DISP/BACK/SCRL
button Press to select different displays. Press and hold to scroll through the
text information. Press to return to the previous display when operating the men
u. Press and hold to return to the main menu when operating the menu. d BAND/ESC
button Press to select among three FM bands and MW/LW bands. Press to return to
the ordinary display when operating the menu.
Program service name, PTY information and other literal information are displaye
d. • Built-in CD player and USB Elapsed playback time and literal information are
displayed. 4 (song) indicator Appears when the track (song) name is displayed on
the main display section. Also, appears when a playable audio file is selected
while operating the list. indicator Appears when an upper tier of folder or menu
exists. (folder) indicator Appears when operating list function. indicator Appe
ars when a lower tier of folder or menu exists.
B
5
6 7
C
Display indication
12 3
8 LOC indicator Appears when local seek tuning is on. 9 a LOUD (loudness) indica
tor Appears when loudness is on. (TA) indicator Appears when TA (traffic announc
ement standby) function is on. (TP) indicator Appears when a TP station is tuned
in. (AF) indicator Appears when AF (alternative frequencies search) function is
on. (stereo) indicator Appears when the selected frequency is being broadcast i
n stereo. (repeat) indicator Shows when track repeat is turned on. Also, shows w
hen folder repeat is on.
D
9 a b c def 57 468
1
g
b c
(disc) indicator Appears when the disc (album) name is displayed on the main dis
play section. (artist) indicator Appears when the disc (track) artist name is di
splayed on the main display section.
2
d
E
3 Main display section Displays band, frequency, elapsed playback time and other
settings. • Tuner Band and frequency are displayed. • RDS
e
F
10
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
f g
(random) indicator Shows when random play is on.
A
(Sound Retriever) indicator Appears when Sound Retriever function is on.
Fastening the front panel
If you do not plan to detach the front panel, the front panel can be fastened wi
th supplied screw.
B
Screw
BPZ20P060FTC
C
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
11
F
E
B
A
D
C
12
5. This product 1. Rear output 20.To Rear output 3. Fuse (10 A) 21. Connect with
RCA cables (sold separately) 22. Power amp (sold separately) 4. Wired remote in
put Hard-wired remote control adaptor can be connected (sold separately).
2.4 CONNECTION DIAGRAM
1
1
6. Note Depending on the kind of vehicle, the function of 3* and 5* may be diffe
rent. In this case, be sure to connect 2* to 5* and 4* to 3*. 1*
2. Antenna jack
3*
2*
5*
4*
7. Connect leads of the same color to each other.
2
2
8. Cap (1*) Do not remove cap if this terminal is not in use. 23. System remote
control 16. Blue/white Connect to system control terminal of the power amp (max.
300 mA 12 V DC). 24. Left 25. Right
DEH-2100UB/XS/EW5
17. Blue/white (7*) Connect to auto-antenna relay control terminal (max. 300 mA
12 V DC). 18. Blue/white (6*) The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and 7* when Pin 5 is an antenna contr
ol type. In another type of vehicle, never connect 6* and 7*. 19. Speaker leads
White: Front left 15. Yellow/black White/black: Front left If you use an equipme
nt with Mute Gray: Front right function, wire this lead to the Audio Gray/black:
Front right Mute lead on that equipment. If not, Green: Rear left keep the Audi
o Mute lead free of any Green/black: Rear left connections. Violet: Rear right V
iolet/black: Rear right
9. Yellow (3*) Back-up (or accessory)
10. Yellow (2*) Connect to the constant 12 V supply terminal.
11. Red (5*) Accessory (or back-up)
12. Red (4*) Connect to terminal controlled by ignition switch (12 V DC).
26.Rear speaker
26.Rear speaker
3
3
13. Black (chassis ground) Connect to a clean, paint-free metal location.
27. Perform these connections when using the optional amplifier.
14. ISO connector Note In some vehicles, the ISO connector may be divided into t
wo. In this case, be sure to connect to both connectors.
4
4
5
6
7
8
3. BASIC ITEMS FOR SERVICE
3.1 CHECK POINTS AFTER SERVICING
A
To keep the product quality after servicing, please confirm following check poin
ts. No. 1 Procedures Confirm whether the customer complain has been solved. If t
he customer complain occurs with the specific media, use it for the operation ch
eck. Play back a CD. (Track search) Check FM/AM tuner action. (Seek, Preset) Swi
tch band to check both FM and AM. Check whether no disc is inside the product. A
ppearance check Item to be confirmed The customer complain must not be reappeare
d. Display, audio and operations must be normal. No malfunction on display, audi
o and operation. Display, audio and operations must be normal. The media used fo
r the operating check must be ejected. No scratches or dirt on its appearance af
ter receiving it for service.
2 CD 3 FM/AM tuner
B
4 5
See the table below for the items to be checked regarding audio: Item to be chec
ked regarding audio Distortion Noise Volume too low Volume too high Volume fluct
uating Sound interrupted
C
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
13
1
2
3
4
3.2 PCB LOCATIONS
A
C CD Core Unit (S10.5COMP2-USB-C3)
B
A Tuner Amp Unit
C
B Keyboard Unit
A:DEH-2100UB/XS/EW5 B:DEH-2120UB/XS/EW5 C:DEH-2110UB/XS/UR Unit Number : Unit Nu
mber : Unit Number : Unit Name : Unit Number : Unit Name : Unit Number : Unit Na
me :
YWM5292(A) YWM5317(B) YWM5316(C) Tuner Amp Unit Keyboard Unit CWX3679 CD Core Un
it(S10.5COMP2-USB-C3)
D
E
F
14
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
3.3 JIGS LIST
- Jigs List
Name Test Disc L.P.F. Jig No. TCD-782 Remarks Checking the grating Checking the
grating (Two pieces)
A
- Grease List
Name Grease Grease Grease No. GEM1024 GEM1045 Remarks CD Mechanism Module CD Mec
hanism Module
B
3.4 CLEANING
C
Before shipping out the product, be sure to clean the following portions by usin
g the prescribed cleaning tools: Portions to be cleaned CD pickup lenses Cleanin
g tools Cleaning liquid : GEM1004 Cleaning paper : GED-008
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
15
1
2
3
4
4. BLOCK DIAGRAM
A
ANTENNA
A TUNER AMP UNIT
SYS+B
CN401
REFA REFB LDET IFA IFB SL-IN
SWVDD3V
CE1 CE2 DO CK DI SLOUT
1
ANT 1 ANT 2 RFGND1
2
3 RFGND2
4 RFGND3
5 RFGND4
6 VCC
7 SLIN
8 IFOUTA
9 IFOUTB
10 DGND
11 REFINA
12 REFINB
13 LDET
14 VDD
15 DI
16 CK
17 CE1
18 DO
19 CE2
20 SLOUT
IC2 EEPROM
SL-IN IFA IFB REFA REFB LDET
B
DI CK CE1 DO
VCO
LFP
CE2 SLOUT
ATT
ATT TANK IC1 MIX / IF / PLL
ATT
RF
LFP
CF
ELECTRON SOURCE
TUNL 2
C
FM/AM TUNER UNIT
IN2_L
CD-Lch
IC PM
1 IN1_L
REGULATOR IC IC911 BA49181-V12
VDDCONT 1 47 36 15 1 B.UP SW5V SWVDD3V SYS+B VDD3V 5 6 7 8 SW5V SWVDD SYS+B VDD
2 BESNS 3 SYSPW SW5VCONT 4 +B 10 +B.UP 9 SWVDD3V
D
SYSTEM COMPU IC601( BSENS PN502
PWROFF SYSPW SWVDD
C CD CORE UNIT(S10.5COMP2-USB-C3)
PICKUP UNIT (P10.5)(SERVICE)
LD LDMD 15 5 15 5 8 AC,BD,E,F XTAL 50 FOM MD FOCUS ACT. TRACKING ACT. 3 3 FOM X2
01 16.93MHz
CN101
Q101
VDD2
RF AMP, CD DECODER, MP3&WMA DECODER DIGITAL SERVO/DATA•PROCESSOR CPU, USB HOST CON
TROLLER
141 142 LD PD REFOUT /USBXTAL 2 USBXTAL 1 X205 48MHz
Q601
85
DREG
9 55 57 94 121
M-REGC PLL_VDD DVDD3 DVDD2 DVDD4
VREF 8
HOLOGRAM UNIT
REFO
133
FOP 2 TOP 1 TOM 4 14 LD+
4
FOP 2 1 TOP TOM
ACTUATOR/ MOTOR DRIVER IC301 BA5839FP
12 FOM 11 FOP 14 TOP 13 TOM
/XTAL 52
USB5V
B.UP 1 8
VDD2
IC501 BD9007F
PVin Vin SW 28 27 USBCTL FLG EN 5 25 SYNC
Q102 VCC TD,FD 39 SD,MD /PUEN LOUT 55 VDD VDD2 VD VDD VD
9 2 1 11 18 19
E
14
CN701
LOUT
13 7
CN651
LOUT USB5V
VDD
IC251 VIN BD6538G
EN 5 VOUT FLG
1 3 4
2
SPINDLE MOTOR
M
16 22 SOP LOEJ 15 SOM 21 18 LCOP CLCONT 17 9 CONT LCOM 28 20 41
IC201 PE5666A
LOEJ CLCONT CONT
VDD3V Q991
VD
CD VD
B.UP Q992 5 126 VDCONT
LOADING/CARRIAGE MOTOR
M
8 7 10 9 S904 12EJ S905 8EJ S901 HOME S903 DSCSNS
12EJ 8EJ DSCSNS HOME /RESET 16 /RESET BRST,BRXEN,BSRQ BDATA,BSCK DP DM 5 4 VD VD
SENS 11 DP 16 DM
17 4 3 8 12
RESET BRST,BRXEN,BSRQ,BDATA,BSCK
16
CDRST
USBZ USBF
F
16
DEH-2100UB/XS/EW5
1 2 3 4
VCK, VDT, VST
5
6
7
8
A
SYSTEM MICRO COMPUTER IC601(1/2) PN5024B
KEYAD KEYD 142 130
CN871
KEYAD KEYD
2 3
WIRED REMOTE
A B
SL-IN IFA IFB REFA REFB LDET DI CK CE1 DO CE2 SLOUT 62 SL 77 IF_INA 78 IF_INB 96
97 99 100 101 102 103 109 136 FREFA FREFB LOCK TUNDO TUNCK CE TUNDI CE2 SL Q351
CN351
RL
2
RCA OUT
B
CN911 ASENSE
Q931 B.UP B.UP ACC 1 3
59
L_OUT
ASENS
35
ASENS
GND
2
ELECTRONIC VOLUME/ SOURCE SELECTOR
TUNL 2 Rear_L IN2_L 7 12 RLIn FL+ FL− 21 23 5 3 25 6 20 TELIN
VCK, VDT, VST
POWER CONNECTOR
FL+ FL− RL+ RL− BREM B.UP 12 10 11 9 6
C
CD Lch
IC151 PML014A
1 IN1_L
Front_L
6
14
FLIn
IN4+_L IN4 _L
4 5
AUX L AUX G
22
AMP IC301 PAL007C
RL+ RL− B.REM VCC
MUTE
4
STBY
VCC
8
MUTE
Q201(2/2)
47 36 15 1 B.UP
SYSTEM MICRO COMPUTER IC601(2/2) BSENS PN5024B
PWROFF SYSPW SWVDD TELIN MUTE
A :DEH 2100UB/XS/EW5 B :DEH 2120UB/XS/EW5 C :DEH 2110UB/XS/UR
D
MUTE
Q201(1/2) 44
TEL IN
Q851 26
A B
VDD3V 85 DREG XOUT XIN 9 55 57 94 121 M REGC PLL_VDD DVDD3 DVDD2 DVDD4 BU_X2 51
BU_X1 52 X602 4.7186MHz 82 81 X601 74.1MHz
B
CN831
AUX L AUX G 7 6 3 7 6 3 ROT1 ROT0
KEYBOARD UNIT
CN1802
AUX R 3 AUX L 2 AUX G 1
CN1801
AUX L AUX G
FRONT AUX
C
SW5V
KEY MATRIX
SW5V S1833 S1801 4 5 3 KST1 KDT2 S1811 S1813 5 S1825 S1826 DOWN
S1815 6
F
5 25 SYNC ROT1 ROT0 28 27 USBCTL FLG B.UP B.UP ILMPW 126 2 111 110
S1803 S1834
CD EJECT
S1805
3
S1807
2
S1809 1
ROT1 ROT0
1 2
BAND/ESC
16 17
16 17
S1817 DISP/BACK S1829 S1830 UP
S1819 TA/ →RF S1831 S1832 LEFT
E
ILLUMI ILMPW
Q821 ILM+B 15 15 ILM+B D1824 D1832 D1834 D1840
4
S1823 LIST
S1827 S1828 RIGH
LCDBK
D1823 Q822
KDT0 3 KST0 4
VDCONT
SOURCE
S1802 16 CDRST SRC 33 SOURCE 4 4 SOURCE
SW5V
REM KYDT DPDT 20 18 10 56 KYDT DPDT VLCD VDD
KEY DATA
X1 X0
23 22 X1801 5.00MHz
KYDT DPDT
24 23
KYDT DPDT
18 19
18 19
LCD DRIVER/ KEY CONTROLLER IC1801 PD6340A
LCD1801
DSENS
34
DSENSE
20
20
DSEN
USB5V USBZ USBF
VBUS D+ D
14 12 13
14 12 13
VBUS D+ D
DEH 2100UB/XS/EW5
5 6 7 8
→
F
CN1803
VBUS D+ D1 3 2
USB
17
1
2
3
4
LCD (CAW1970)
A
B
C
D
E
SEGMENT
F
18
DEH 2100UB/XS/EW5
1 2 3 4
COMMON
5
6
7
8
5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
Power ON
VDD = 3.3 V Pin 8
BSENS Pin 36 BSENS = L ASENS Pin 35 ASENS = L
Starts communication with Grille microcomputer.
C B
SWVDD < H Pin 1
300 ms
Source keys operative
300 ms In case of the above signal, the communication with Grille microcomputer
may fail. If the time interval is not 300 msec, the oscillator may be defective.
Source ON
D
SYSPW < H Pin 15
Completes power on operation. (After that, proceed to each source operation)
E
F
DEH 2100UB/XS/EW5
5 6 7 8
19
1
2
3
4
5.2 ERROR CODE LIST
Error Messages
A
If a CD is not operative or stopped during operation due to an error, the error
mode is turned on and cause(s) of the error is indicated with a corresponding nu
mber. This arrangement is intended at reducing nonsense calls from the users and
also for facilitating trouble analysis and repair work in servicing.
(1) Basic Indication Method 1) When SERRORM is selected for the CSMOD (CD mode a
rea for the system), error codes are written to DMIN (minutes display area) and
DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO rem
ains in blank as before.
B
2) Head unit display examples Depending on display capability of LCD used, displ
ay will vary as shown below. xx contains the error number. 8 digit display ERROR
xx (2) Error Code List Code 10 Class Electricity Displayed error code Carriage
Home NG SERVO LSI Communication Error 11 12 Electricity Electricity Focus Servo
NG Spindle Lock NG Subcode NG Description of the code and potential cause(s) CRG
can't be moved to inner diameter. CRG can't be moved from inner diameter. > Fa
ilure on home switch or CRG move mechanism. Communication error between microcom
puter and SERVO LSI. Focusing not available. > Stains on rear side of disc or e
xcessive vibrations on REWRITABLE. Spindle not locked. Sub code is strange (not
readable). > Failure on spindle, stains or damages on disc, or excessive vibrat
ions. A disc not containing CD R data is found. Turned over disc are found, thou
gh rarely. 17 Electricity Electricity Electricity
Mechanism
6 digit display ERR xx
4 digit display E xx
C
Setup NG Search Time Out ALL Skip CD On Mech Error Power Supply NG
CD signal error. AGC protection doesn't work. Focus can be easily lost. > Damag
es or stains on disc, or excessive vibrations on REWRITABLE. Failed to reach tar
get address. > CRG tracking error or damages on disc. Skip setting for all trac
k. (CD R/RW) Mechanical error during CD ON. > Defective loading motor, mechanic
al lock and mechanical sensor. Power (VD) is ground faulted. > Failure on SW tr
ansistor or power supply (failure on connector).
D
30 44 50 A0
E
System
Remarks: Mechanical errors are not displayed (because a CD is turned off in thes
e errors). Unreadable TOC does not constitute an error. An intended operation co
ntinues in this case. Upper digits of an error code are subdivided as shown belo
w: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.
F
20
DEH 2100UB/XS/EW5
1 2 3 4
5
6
7
8
A
B
C
D
E
F
DEH 2100UB/XS/EW5
5 6 7 8
21
1
2
3
4
5.3 CONNECTOR FUNCTION DESCRIPTION
A
REAR OUTPUT
B
ANTENNA
WIRED REMOTE CONTROL (2100, 2120)
16 14 12 10 8 6 4 15 13 11 9 7 5 3
2 1
C
16 15 14 13 12 11 10 9
FR+ RR+ FRRRFL+ RL+ FLRL
8 7 6 5 4 3 2 1
MUTE NC B.REM NC A.ANT ACC GND B.UP
D
E
F
22
DEH 2100UB/XS/EW5
1 2 3 4
5
6
7
8
6. SERVICE MODE
6.1 DISPLAY TEST MODE
A
1. To enter the test mode Turn on ACC and Backup while pressing the 1 and the 3
buttons together. 2. To exit from the test mode Turn off the ACC and Backup. 3.
Operation method
B
Change display as follows by pressing the 1 and the 3 buttons together. System v
ersion display ROM Correction version display Normal display Display stop All li
ghting of display
C
All lights out of display LCD check mode 1 LCD check mode 2 LCD check mode 3
LCD check mode 1
D
LCD check mode 2
E
LCD check mode 3
F
DEH 2100UB/XS/EW5
5 6 7 8
23
1
2
3
4
6.2 CD TEST MODE
Flow Chart
[Key]
A
Contents Display
[4] + [6] + Reset or [4] + [6] + BU + ACC Test Mode In
[CD] or [SOURCE] Source On TRK MIN SEC
[BAND] Power On (T.Offset is adjusted) TRK MIN SEC
[3] Power On (T.Offset is not adjusted) TRK MIN SEC
[2] RF AMP *1 Gain switching TRK MIN SEC
[4] SPINDLE *9 Speed switching TRK MIN SEC
00
00
00
99
99
99
GG
GG
GG
SP
SP
SP
B
[BAND] Power Off TRK MIN SEC
[3] Focus Close S curve check TRK MIN SEC
[6] Focus Mode switching
[1]
[>] CRG +
[<] CRG
[2] Self adjusting switching *3 TRK MIN SEC
*2
TRK MIN SEC
Tracking Servo Close
[5] Gop Mode *10 Gop Mode switching TRK MIN SEC
91
91
91
0X
0X
0X
00 00 00 or 99 99 99
*8 00 00 00 or 99 99 99
*8 00 00 00 or 99 99 99
??
??
??
OL
OL
OL
[1] T.Close & AGC Applicable servomechanism TRK MIN SEC
[6] T.Close Applicable servomechanism TRK MIN SEC
[3] RF AGC / RF AGC coefficient display TRK MIN SEC
[>] CRG +
[<] CRG
[2] T.Balance adjustment / T.BAL coefficient display TRK MIN SEC
?tr ?min ?sec
?tr ?min ?sec
??
??
??
8X 8X 8X or 9X 9X 9X
??
??
??
[1] F,T,RF AGC *7 F.Bias display switching TRK MIN SEC
[3] F,T AGC / F.Bias RF AGC TRK MIN SEC
[6] CRG/TR jump value switching*5 TRK MIN SEC
[>] CRG/TR Jump +
[<] CRG/TR Jump
[2] Tracking Open
*4
TRK MIN SEC TRK MIN
*4
SEC
C
??
??
??
?tr ?min ?sec
?tr ?min ?sec
?tr ?min ?sec
?tr ?min ?sec *6
[2] Tracking Open
*1)
TRK
TYP
MIN SEC
>
TRK
+ 6 dB > 06MIN06SEC06
TRK
+ 12 dB 12MIN12SEC12
D
*2) Focus Close > S.Curve > TRK TRK 00MIN00SEC00 01MIN01SEC01 (TRK99MIN99SEC99
)
F EQ measurement setting TRK 02MIN02SEC02
[Key] [BAND] [>] [<] [1]
Operation Test Mode Power On/Off CRG + / TR Jump + (Direction of the external su
rface) CRG / TR Jump (Direction of the internal surface) T. CLS & AGC & Applic
able servomechanism / AGC,AGC display setting RF Gain switching / Offset adjustm
ent display / T.Balance adjustment / T. Open F. Close,S Curve / Rough Servo and
RF AGC / F,T,RF AGC SPDL 1X/2X switching As for the double speed(2x), audio outp
ut cannot be supported. Error Rate measurement ON : ERR 30 Counts Start BER disp
lay data[%] F. Mode switching / Tracking Close / CRG•TR Jump Switching
*3) F.Offset Display > RF.Offset > T.Offset Display > Switch to the order of
the original display
[2] [3]
*4) 1TR/4TR/10TR/32TR/100TR *5) Single > 4TR > 10TR > 32TR > 100TR > CRG Mo
ve 9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86) *6) Only at the time of CRG
move, 100TR jump
E
[4]
[5]
*7) TRK/MIN/SEC > F.AGC > T.AGC Gain > F Bias > RF AGC
[6]
*8) CRG motor voltage = 2 [V] *9)
TRK
TYP (1X)
MIN SEC
>
TRK
2X > 22MIN22SEC22
TRK
1X 11MIN11SEC11
*10)
OFF(TYP)
TRK MIN SEC
>
TRK
FORCUS > 70MIN70SEC70
TRK
TRACKING 71MIN71SEC71
F
• As for the double speed (2x), audio output cannot be supported • After the [Eject]
key is pressed keys other than the [Eject] key should not be pressed, until dis
c ejection is complete. • When the key [2] or [3] is pressed during the Focus Sear
ch, the power supply should be immediately turned off (otherwise the lens sticks
to Wall, causing the actuator to be damaged). • In the case of TR jump other than
to 100TR, the function shall continue to be processed even if the TR jump key i
s released. As for the CRG Move and 100TR Jump, the mechanism shall be set to th
e Tracking Close mode when the key is released. • When the power is turned on/off
the jump mode is reset to the Single TR (91) while the gain of the RFAMP is rese
t to 0 dB. At the same time all the self adjusting values shall return to the de
fault setting.
24
DEH 2100UB/XS/EW5
1 2 3 4
5
6
7
8
7. DISASSEMBLY
Removing the Case (not shown)
1. Remove the Case.
A
Removing the CD Mechanism Module (Fig.1)
CD Mechanism Module
1
Release the two latches and then remove the Panel Assy.
2
2
Remove the four screws.
2
Disconnect the connector and then remove the CD Mechanism Module.
B
2 1
2 1 2
C
Panel Assy
Fig.1
Removing the Tuner Amp Unit (Fig.2)
1 2 3 4
Remove the two screws.
D
Remove the three screws.
1
1
Remove the two screws.
Straighten the tabs at two locations indicated and then remove the Tuner Amp Uni
t.
2
E
2 3 3 2 4 4
Tuner Amp Unit
Fig.2
F
DEH 2100UB/XS/EW5
5 6 7 8
25
1
2
3
4
How to hold the Mechanism Unit
1. Hold the Upper and Lower Frames. 2. Do not hold the front portion of the Uppe
r Frame, because it is not very solid.
A
B
Do not squeeze this area.
Removing the Upper and Lower Frames
1. With a disc inserted and clamped in the mechanism, remove the two Springs (A)
, the six Springs (B), and the four Screws. 2. Turn the Upper Frame using the pa
rt "a" as a pivot, and remove the Upper Frame. 3. While lifting the Carriage Mec
hanism, remove it from the three Dampers. Caution: When assembling, be sure to a
pply some alcohol to the Dampers and assemble the mechanism in a clamped state.
C
a B B
Upper Frame
B B
D
B B A
Damper
A
E
Carriage Mechanism Lower Frame Damper
F
26
DEH 2100UB/XS/EW5
1 2 3 4
5
6
7
8
How to remove the CD Core Unit
1. Apply Shorting Solder to the flexible cable of the Pickup, and disconnect it
from the connector. 2. Unsolder the four leads, and loosen the Screw. 3. Remove
the CD Core Unit. Caution: When assembling the CD Core Unit, assemble it with th
e SW in a clamped state so as not to damage it.
Shorting Solder
A
Screw
B
CD Core Unit
Solder
How to remove the Pickup Unit
1. Make the system in the carriage mechanism mode, and have it clamped. 2. Remov
e the CD Core Unit and remove the leads from the Inner Holder. 3. Remove the Pol
y Washer, Change Arm, and Pickup Lock Arm. 4. While releasing from the hook of t
he Inner Holder, lift the end of the Feed Screw. Caution: When assembling, move
the Planet Gear to the load/eject position before setting the Feed Screw in the
Inner Holder. Assemble the sub unit side of the Pickup, taking the plate (Chassi
s) in between. When treating the leads of the Load Carriage Motor Assy, do not m
ake them loose over the Feed Screw.
Poly Washer Change Arm Pickup Lock Arm Inner Holder
D C
Feed Screw
Planet Gear
Pickup Rack
E
Chassis
Pickup
F
DEH 2100UB/XS/EW5
5 6 7 8
27
1
2
3
4
8. EACH SETTING AND ADJUSTMENT
8.1 CD ADJUSTMENT
A
B
1) Cautions on adjustments In this product the single voltage (3.3 V) is used fo
r the regulator. The reference voltage is the REFO1 (1.65 V) instead of the GND.
If you should mistakenly short the REFO1 with the GND during adjustment, accura
te voltage will not be obtained, and the servo’s misoperation will apply excessive
shock to the pickup. To avoid such problems: a. Do not mix up the REFO1 with th
e GND when connecting the (-) probe of measuring instruments. Especially on an o
scilloscope, avoid connecting the (-) probe for CH1 to the GND. b. In many cases
, measuring instruments have the same potential as that for the (-) probe. Be su
re to set the measuring instruments to the floating state. c. If you have mistak
enly connected the REFO1 to the GND, turn off the regulator or the power immedia
tely. Before mounting and removing filters or leads for adjustment, be sure to t
urn off the regulator. For stable circuit operation, keep the mechanism operatin
g for about one minute or more after the regulator is turned on. In the test mod
e, any software protections will not work. Avoid applying any mechanical or elec
trical shock to the mechanism during adjustment. The RFI and RFO signals with a
wide frequency range are easy to oscillate. When observing the signals, insert a
resistor of 1k ohms in series. The load and eject operation is not guarantied w
ith the mechanism upside down. If the mechanism is blocked due to mistaken eject
operation, reset the product or turn off and on the ACC to restore it.
2) Test mode This mode is used to adjust the CD mechanism module. To enter the t
est mode. While pressing the 4 and 6 keys at the same time, reset. To exit from
the test mode. Turn off the ACC and back up. Notes: a. During ejection, do not p
ress any other keys than the EJECT key until the loaded disc is ejected. b. If y
ou have pressed the (->) key or (<-) key during focus search, turn off the power
immediately to protect the actuator from damage caused by the lens stuck. c. Fo
r the TR jump modes except 100TR, the track jump operation will continue even if
the key is released. d. For the CRG move and 100TR jump modes, the tracking loo
p will be closed at the same time when the key is released. e. When the power is
turned off and on, the jump mode is reset to the single TR (91), the RF amp gai
n is set to 0 dB, and the auto-adjustment values are reset to the default settin
gs.
C
D
E
F
28
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT
A
Note : The grating angle of the PU unit cannot be adjusted after the PU unit is
changed. The PU unit in the CD mechanism module is adjusted on the production li
ne to match the CD mechanism module and is thus the best adjusted PU unit for th
e CD mechanism module. Changing the PU unit is thus best considered as a last re
sort. However, if the PU unit must be changed, the grating should be checked usi
ng the procedure below. Purpose : To check that the grating is within an accepta
ble range when the PU unit is changed. Symptoms of Mal-adjustment : If the grati
ng is off by a large amount symptoms such as being unable to close tracking, bei
ng unable to perform track search operations, or taking a long time for track se
arching. Method : Measuring Equipment Measuring Points Disc Mode
B
Oscilloscope, Two L.P.F. E, F, REFO1 TCD-782 TEST MODE
CD CORE UNIT
REFO1 E F E VREF L.P.F. Xch 100 kohm 390 pF Ych
C
Oscilloscope
F VREF
100 kohm 390 pF L.P.F.
D
Checking Procedure 1. In test mode, load the disc and switch the 3 V regulator o
n. 2. Using the -> and <- buttons, move the PU unit to the innermost track. 3. P
ress key 3 to close focus, the display should read "91". Press key 2 to implemen
t the tracking balance adjustment the display should now read "81". Press key 3.
The display will change, returning to "81" on the fourth press. 4. As shown in
the diagram above, monitor the LPF outputs using the oscilloscope and check that
the phase difference is within 75 degrees. Refer to the photographs supplied to
determine the phase angle. 5. If the phase difference is determined to be great
er than 75 degrees try changing the PU unit to see if there is any improvement.
If, after trying this a number of times, the grating angle does not become less
than 75 degrees then the mechanism should be judged to be at fault. Note Because
of eccentricity in the disc and a slight misalignment of the clamping center th
e grating waveform may be seen to "wobble" ( the phase difference changes as the
disc rotates). The angle specified above indicates the average angle. Hint Relo
ading the disc changes the clamp position and may decrease the "wobble".
E
F
DEH-2100UB/XS/EW5
5 6 7 8
29
1
2
3
4
Grating waveform
A
Ech -> Xch 20 mV/div, AC Fch -> Ych 20 mV/div, AC 30 degrees
0 degrees
B
45 degrees
C
60 degrees
D
75 degrees
90 degrees
E
F
30
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
A
B
C
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
31
1
2
3
4
9. EXPLODED VIEWS AND PARTS LIST
NOTES : Parts marked by " * " are generally unavailable because they are not in
our Master Spare Parts List.
A
The > mark found on some component parts indicates the importance of the safety
factor of the part. Therefore, when replacing, be sure to use parts of identical
designation. Screw adjacent to mark on the product are used for disassembly. Fo
r the applying amount of lubricants or glue, follow the instructions in this man
ual. (In the case of no amount instructions,apply as you think it appropriate.)
" "
9.1 PACKING
B
C
D
E
F
32
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
(1) PACKING SECTION PARTS LIST
Mark No. 1 2 * 3 4 5 6 * 7 8 9 10 11 Description Cord Assy Polyethylene Bag Acce
ssory Assy Screw Screw Assy Screw Polyethylene Bag Screw Screw Polyethylene Bag
Handle Part No. See Contrast table (2) CEG-162 YEA5070 BPZ20P060FTC CEA3849 16 C
BA1650 CEG-127 CRZ50P090FTC TRZ50P080FTC CEG1160 18-4 Installation Manual CND370
7 See Contrast table (2)
B
Mark No. 12 13 14 15 Bush
Description Unit Box Contain Box Protector Protector Case Assy
Part No. CNV3930 See Contrast table (2) See Contrast table (2) YHP5050 YHP5051 Y
XB5009 See Contrast table (2) See Contrast table (2) See Contrast table (2)
A
17

18-1 Owner s Manual 18-2 Owner s Manual * 18-3 Warranty Card
(2) CONTRAST TABLE DEH-2100UB/XS/EW5, DEH-2120UB/XS/EW5 and DEH-2110UB/XS/UR are
constructed the same except for the following:
Mark
1 13 14 18-1 18-2 * 18-3 18-4
No.
Description
Cord Assy Unit Box Contain Box Owner s Manual Owner s Manual Warranty Card Insta
llation Manual
DEH-2100UB/XS/EW5
CDP1015 YHG5449 YHL5449 YRD5217 YRD5218 CRY1279 YRD5219
DEH-2120UB/XS/EW5
CDP1015 YHG5450 YHL5450 YRD5217 YRD5218 CRY1279 YRD5219
DEH-2110UB/XS/UR
CDP1016 YHG5452 YHL5452 YRB5097 Not used YRY5003 Not used
C

Owner s Manual,Installation Manual
Part No.
YRD5217 YRD5218 YRD5219 YRB5097
Language
English, Spanish(Espanol), German, French Italian, Dutch, Russian English, Spani
sh(Espanol), German, French, Italian, Dutch, Russian Russian
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
33
1
2
3
4
9.2 EXTERIOR (1)
A
B
B
A
B
C
A
D
A
E
F
34
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
(1) EXTERIOR (1) SECTION PARTS LIST
Mark No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Description Screw Sc
rew Screw Screw Holder Part No. BSZ25P060FTB BSZ26P060FTC BSZ26P100FTC BSZ26P160
FTC CND4748 > Mark No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
40 Description Holder Terminal(CN402) Terminal(CN601) Terminal(CN801) Fuse(10 A)
Holder Holder Heat Sink Chassis Unit Button Spring Spring(Black) Spring(Silver)
Cover Panel Arm Arm IC(IC301) IC(IC911) Transistor(Q991) Part No. CND3466 VNF10
84 VNF1084 VNF1084 YEK5001 See Contrast table (2) YND5034 YNR5123 See Contrast t
able (2) CAC4836 CBH2367 CBH2962 CBH2961 CNN1665 CNS9662 CNW1439 CNV9312 PAL007C
BA49181-V12 2SD2396
C B A
CD Mechanism Module(S10.5) CXK5778 Screw Cable Tuner Amp Unit Screw Screw Screw
Pin Jack(CN351) Plug(CN911) Connector(CN651) Connector(CN871) Connector(CN831) A
ntenna Jack(CN401) Holder FM/AM Tuner Unit ISS26P055FTC YDE5043 See Contrast tab
le (2) BPZ26P080FTC BSZ26P060FTC BSZ26P200FTC CKB1056 CKM1376 CKS3833 See Contra
st table (2) CKS6050 CKX1070 CND3706 See Contrast table (2)
Mark
9 16 20 26 29
No.
Description
Tuner Amp Unit Connector(CN871) FM/AM Tuner Unit Holder Chassis Unit
DEH-2100UB/XS/EW5
YWM5292 CKS4124 CWE2106 YND5025 YXA5539
DEH-2120UB/XS/EW5
YWM5317 CKS4124 CWE2106 YND5025 YXA5540
DEH-2110UB/XS/UR
YWM5316 Not used CWE2123 YND5026 YXA5541
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
35
1
2
3
4
9.3 EXTERIOR (2)
A
B
B
C
D
E
F
36
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
(1) EXTERIOR (2) SECTION PARTS LIST
Mark No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Description Cord Assy Terminal Cove
r Holder Case Panel Detachable Assy Screw Spring Button(EJECT) Button(1-6) Butto
n(TA/AF, DOWN) Button(LEFT, UP, RIGHT) Button(SRC/BAND) Button(LIST/DISP) Button
(DETACH) Part No. See Contrast table (2) CKX-003 CND3598 YNB5046 YNS5406 See Con
trast table (2) BPZ20P100FTC CBH2210 YAC5341 YAC5342 YAC5343 YAC5344 YAC5345 YAC
5346 YAC5347 Mark No. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Description C
over Grip(USB) LCD(LCD1801) Connector(CN1801) ••••• Jack(CN1802) Connector(CN1803) Holder
Rubber Connector Lighting Conductor Grille Unit Knob Unit Spring ••••• YKN5001 YKS5032 YNC
5061 YNV5169 YNV5170 YNV5171 See Contrast table (2) YXC5102 YBL5010
B
Part No. YNS5405 YNV5176 CAW1970 CKS6049
A
Mark
1 6 27
No.
Description
Cord Assy Detachable Assy Grille Unit
DEH-2100UB/XS/EW5
CDP1015 YXA5546 YXA5498
DEH-2120UB/XS/EW5
CDP1015 YXA5551 YXA5499
DEH-2110UB/XS/UR
CDP1016 YXA5547 YXA5501
C
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
37
1
2
3
4
9.4 CD MECHANISM MODULE
5
A
19 27 5
5 19
(1)
19 13
(1)
29
48 5 19
A
20 57
B
B
66 9 44 44 15 60
(2)
13
16
(1)
25 54
(1)
23 31
C
9 72 8
(2)
58 69 71 70
73 21
C
46 38 39 33 62
70 68 40 28 32
(1) (1) (1)
63
7 50
4 36 47 17 35 37 14
(2)
(1)
B
(1) (1) (2)
4 61
(2)
52
C
53
18
45 12 64
(1)
D
41 5
6
(2)
(1)
49
D
8 51 55
A
65
(1) (2)
51
59
(1) (1)
C
74 1 3
E
43 10
(2) (1)
56
D
E
2
22 34
(1) (1)
19
(1)
(1)
11 42 24
(1) (1) (1)
26
19
F
30
67 24 (1) : GEM1024 (2) : GEM1045
E
38
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
CD MECHANISM MODULE SECTION PARTS LIST
Mark No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 Description C
onnector(CN101) Connector(CN701) Screw Screw Screw(M2 x 3) Screw(M2 x 4) Washer
Roller Spring Spring Spring Spring Spring Spring Spring Spring Spring Spring Spr
ing Spring Spring Spring Spring Spring Arm Frame Bracket Arm Lever Arm Bracket A
rm Lever Holder Gear Gear Gear Gear Gear Gear Rack Arm Roller Gear Guide Gear Gu
ide Arm Part No. CKS4808 CKS5854 BMZ20P025FTC BSZ20P040FTC CBA1511 CBA1835 CBF10
38 CNV9499 CBH2609 CBH2612 CBH2614 CBH2616 CBH2617 CBH2620 CBH2855 CBH2937 CBH27
35 CBH2854 CBH2642 CBH2856 CBH2857 CBH2860 CBH2861 CBL1686 CND1909 CND2582 CND25
83 CND3831 CND2585 CND2586 CND2587 CND2588 CND2589 CNV9522 CNV7207 CNV9513 CNV72
09 CNV9514 CNV9515 CNV9516 CNV9517 CNV7216 CNV8189 CNV9518 CNV9519 CNV7595 CNV95
20 CNV7805
F E D
Mark No. 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73
74 Rack
Description
Part No. CNV8342
A
CD Core Unit(S10.5COMP2-USB-C2) CWX3679
Roller Holder Arm Guide Arm Arm Arm Clamper Arm Guide Arm Collar Motor Unit(M2)
Arm Unit Chassis Unit Gear Unit Frame Unit Motor Unit(M1) Screw Unit Screw Screw
Washer Pickup Unit(P10.5)(Service) Screw
CNV8343 CNV8344 CNV8345 CNV9498 CNV8348 CNV8349 CNV8350 CNV8365 CNV8386 CNV8396
CNV9521 CNV8447 CXC4026 CXC4027 CXC4028 CXC4029 CXC4031 CXC7134 CXC6359 JFZ20P02
5FTC JGZ17P022FTC YE20FTC CXX1942 IMS26P030FTC
C B
DEH-2100UB/XS/EW5
5 6 7 8
39
1
2
3
4
10. SCHEMATIC DIAGRAM
10.1 TUNER AMP UNIT(GUIDE PAGE)
A
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PART
S LIST" or "ELECTRICAL PARTS LIST".
A-a A-b
Large size SCH diagram
NM : No Mount NOTE : Symbol indicates a resistor. No differentiation is made bet
ween chip resistors and discrete resistors. Symbol indicates a capacitor. No dif
ferentiation is made between chip capacitors and discrete capacitors.
A-a
C
CN701
A-a
A-b
Guide page
For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes:
A-a A-b
Detailed page
Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms
*Capacitors Code Practical value 103 0.01uF 101/10 100uF/10V
B
FM/AM TUNER UNIT
C
A,B:CWE2106 C:CWE2123
ANTENNA
A,B
A,B
A,B:103 C:104
D
A,B:103 C:104
C
E
A,B
B
CN1801
F
A
40 DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
A
A-b
701 A : DEH-2100UB/XS/EW5 B : DEH-2120UB/XS/EW5 C : DEH-2110UB/XS/UR
A
TUNER AMP UNIT
3A
B
>
C
C
D
POWER IC
600uH
YEK5001 10A
>
E
A,B
A,B
F
designation.
A
8
DEH-2100UB/XS/EW5
5 6 7
41
F
E
B
A
D
C
42
A-a A-b
A-b A
TUNER AMP UNIT
A : DEH-2100UB/XS/EW5 B : DEH-2120UB/XS/EW5 C : DEH-2110UB/XS/UR
1
3A
1
>
2
2
DEH-2100UB/XS/EW5
3 4
3
4
C
5
5
POWER IC
600uH
YEK5001 10A
>
6
6
DEH-2100UB/XS/EW5
7
7
A,B
A,B
8
8
A-a A-b
designation.
A-b
E D
43
A
C
B
F
F
E
B
A
D
C
A,B
A,B:103 C:104
44
A-a A-b
A-a
C
CN701
NM : No Mount
A-b
1
1
NOTE : Symbol indicates a resistor. No differentiation is made between chip resi
stors and discrete resistors.
Symbol indicates a capacitor. No differentiation is made between chip capacitors
and discrete capacitors.
For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes: *Capacitors Code Practical value 103
0.01uF 101/10 100uF/10V
Ex. *Resistors Code Practical value 123 12k ohms 103 10k ohms
2
2
DEH-2100UB/XS/EW5
A,B
A,B:CWE2106 C:CWE2123
FM/AM TUNER UNIT
3
3
4
4
ANTENNA
5
6
7
8
A-b
B
CN1801
C A,B
A-a A-b
A
B
C
5
A,B
A,B:103 C:104 A,B:103 C:104
D
E
F
A-a
DEH-2100UB/XS/EW5
6 7 8
45
1
2
3
4
10.2 KEYBOARD UNIT
A
473
B
PD6340A
5.00 MHz
C
D
A,C
MC2848-11
MC2848-11
B
561 391
E
F
B
1 2 3 4
5
6
7
8
A : DEH-2100UB/XS/EW5 B : DEH-2120UB/XS/EW5 C : DEH-2110UB/XS/UR
B
KEYBOARD UNIT
A
B
AUX
MULTI-CONTROL
A
CN831
C
D
B
561 391
USB
E
F
B
DEH-2100UB/XS/EW5
5 6 7 8
47
1
2
3
4
10.3 CD MECHANISM MODULE(GUIDE PAGE)
A
C-a
PICKUP UNIT(P10.5)(SERVICE)
F T C S
B
F
f
T F T F F T T F F T T
d
C
c
SWITCHES: CD CORE UNIT(S10.5COMP2-iPod-C2) S901:HOME SWITCH.........ON-OFF S903:
DSCSNS SWITCH.....ON-OFF S904:12EJ SWITCH............ON-OFF S905:8EJ SWITCH.....
.........ON-OFF The underlined indicates the switch position.
D
M1 CXC7134 SPINDLE MOTOR
S S C C
M2 CXC4026 LOADING/CARRIAGE MOTOR
T
e 9 a
S
7
C
F
E
8 4 5
F F
3 2 1
T T
S S C
ACTUATOR/ MOTOR DRIVER
F
C
1 2 3 4
C
5
6
7
8
C-b
C
CD CORE UNIT(S10.5COMP2-USB-C3)
A
F T C S
SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SER
VO LINE
b
B
PE5666A
C
m
l k
D
A
6 CN651
E
g
h
i j
F
C
DEH-2100UB/XS/EW5
5 6 7 8
49
F
E
B
A
D
C
50
C-a C-b
C-b
1
F T C S
1
C
1
2
SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SER
VO LINE
2
b
2
DEH-2100UB/XS/EW5
3 4
PE5666A
3
4
m
5
6
7
8
CN651
A
A
6
i j
B
g
h
C
C-a C-b
D
m
l k
E
F
C-b
DEH-2100UB/XS/EW5
5 6 7 8
51
F
E
B
A
D
C
52
C-b
C-a
C-a C-b
1
1
1 2
PICKUP UNIT(P10.5)(SERVICE)
F T
2
F
2
C S
f
T F T F
DEH-2100UB/XS/EW5
F T T F F T T
3
3
d
c
4
4
.........ON-OFF
.........ON-OFF
The underlined indicates the switch position.
5
1
ACTUATOR/ MOTOR DRIVER
S S C
C
5
S S C C T S
M1 CXC7134 SPINDLE MOTOR
6
F
6
M2 CXC4026 LOADING/CARRIAGE MOTOR
e 9 a
C
7 8 4 5
F F T T
DEH-2100UB/XS/EW5
C-a C-b
3
7 E D
7
2
8
8
C-b
C-a
53
A
C
B
F
1
2
3
4
10.4 WAVEFORMS
A
- CD CORE UNIT
1DSCSNS 28SNS 312SNS 4LOEJ 5 V/div 5 V/div 5 V/div 5 V/div
Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V) 500 ms/div 1DSCSNS 5CLCONT 4LOEJ 6VD 5 V/div
5 V/div 5 V/div 10 V/div 500 ms/div 1DSCSNS 28SNS 312SNS 4LOEJ 5 V/div 5 V/div 5
V/div 5 V/div 500 ms/div
12 cm CD Loading operation
Ref.: GND
B
Ref.: GND Mode: Normal
Mode: Normal
7SIN 8CIN 9TIN
1 V/div 1 s/div 500 mV/div 1 V/div
0FIN 200 mV/div 500 ms/div @TE !RFOK(MONI_3) 2 V/div #FE 7SIN 2 V/div
12 cm CD-DA Source On setup operation
500 mV/div 200 ms/div 500 mV/div
12 cm CD-DA setup operation after loading
C
Source On setup operation
Ref.: REFO Mode: Normal
D
#FE 0FIN @TE 9TIN
500 mV/div 20 ms/div 500 mV/div 500 mV/div 500 mV/div
$MDX 7SIN
2 V/div 200 ms/div $MDX 500 mV/div 7SIN
2 V/div 5 µs/div 500 mV/div
CD-DA Play operation
Spindle waveform during play operation
Spindle waveform during play operation (Wider)
E
0FIN #FE
500 mV/div 200 ms/div @TE 500 mV/div %RFAGC
500 mV/div 2 ms/div 500 mV/div
%RFAGC @TE 9TIN
1 V/div 500 µs/div 500 mV/div 500 mV/div
Focus Search waveform
Track Open waveform
1 Track Jump waveform
Ref.: REFO Mode: TEST
F
54
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
%RFAGC @TE 9TIN
%RFAGC @TE 9TIN
%RFAGC @TE 9TIN
1 V/div 2 ms/div 500 mV/div 500 mV/div
A
4 Tracks Jump waveform
B
%RFAGC @TE 8CIN 7SIN
1 V/div 1 V/div 1 V/div 2 V/div
200 ms/div ^LOUT &ROUT
1 V/div 1 V/div
200 µs/div
1DSCSNS 28SNS 312SNS 4LOEJ
500 ms/div
Search operation(Outter to Inner)
Analog audio waveform
12 cm CD Eject operation
Ref.: AGND Mode: Normal
C
1DSCSNS 5CLCONT 4LOEJ
5 V/div 5 V/div 5 V/div
500 ms/div 1DSCSNS 28SNS 312SNS 4LOEJ
500 ms/div %RFAGC 9TIN @TE 0FIN
500 µs/div
Black dot(800 µm) during play
D
*DP (DM
1 V/div 1 V/div
50 ns/div
*DP (DM
2 V/div 2 V/div
50 ms/div
*DP (DM
2 V/div 2 V/div
50 ms/div
E
USB Play
USB device inserting to USB connector.
CD Play with USB(iPod) device connecting.
F
DEH-2100UB/XS/EW5
5 6 7 8
55
1
2
3
4
A
*DP (DM
2 V/div 2 V/div
50 ms/div
)CPRST ⁄SDA SCL
2 V/div 2 V/div 2 V/div
500 ms/div
ACC OFF with USB(iPod) device connecting.
iPod Authentication Operation
B
C
D
E
F
56
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
A
B
C
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
57
1
2
3
4
11. PCB CONNECTION DIAGRAM
11.1 TUNER AMP UNIT
A
NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB include all necessary parts for several destinat
ion. For further information for respective destinations, be sure to check with
the schematic diagram. 2.Viewpoint of PCB diagrams
A
TUNER AMP UNIT
CORD ASSY
Connector
Capacitor
SIDE A
B
P.C.Board
Chip Part
SIDE B
C
D
E
C
CN701
F
B
CN1801
A
1 2 3 4
5
6
7
8
A
SIDE A
ASSY
W.REM(2100, 2120)
RCA
ANTENNA
B
C
FM/AM TUNER UNIT
D
E
FRONT
F
A
DEH-2100UB/XS/EW5
5 6 7 8
59
1
2
3
4
A
A
TUNER AMP UNIT
> FU 351 (B,138,128) Fuse 3 A CEK1286
B
C
D
E
F
A
1 2 3 4
5
6
7
8
SIDE B
A
B
C
D
E
A
DEH-2100UB/XS/EW5
5 6 7 8
F
61
F
E
B
A
D
C
D1847 D1830
30
TA/RF
S1828
LIST MULTI-CONTROL
S1833 S1827 D1848 D1831
SOURCE
D1825
D1842
S1831
DEH-2100UB/XS/EW5
S1830 S1829 S1819 LCD1801 D1832 D1849 S1809 S1825 S1826 D1827 D1846
20 3
S1805 D1834 D1852
BAND/ESC
D1828 D1845
1
S1807 D1836 D1850 D1851 D1835
2
4
S1811
D1837
D1854
D1856
D1839
D1855 D1838
10
S1801
S1817
S1832
S1813
5
6
S1815
IC1802 1
Y
30 40 50 60 70 80
DISP/BACK
0
X
10
20
90
100
110
120
130
1
5
10
15
20
25
30
35
40
62
B
B
KEYBOARD UNIT
D1840 D1857 S1803 S1834
11.2 KEYBOARD UNIT
1
1
2
5 D1823
2
40
S1802
S1823
EJECT CN1803
1
D1843 D1826
USB
D1829 D1844
D1841 D1824
CN1802
3
3
AUX
1
140
150
160
4
4
SIDE A
B
C
D
A
E
F
SIDE B
B
A
CN831
R1837 D1807 D1806 D1803 R1806 C1807 R1804 C1802 D1804 R1810 C1803 IC1801
1
8
40
7
R1818
R1813
R1814
5 10 15 20 25 30
C1806 D1805 C1805
R1836
R1820
Q1806 1 5 15
C1804
R1839
R1807 R1803
R1829
R1801 D1801 D1802
X1801 1
R1815 R1802 C1801
R1834
R1828
6
Y
110 100 90 80 70
10 20
160
150
140
130
120
60
50
40
30
20
10
0
X
KEYBOARD UNIT
5
B
5
6
35
40
45
L1801
55
R1809 R1808
30
R1833
R1832
R1811
R1838
20
R1812
R1835
Q1805
R1816
CN1801
R1819
R1817
10
DEH-2100UB/XS/EW5
50
7
60
8
1
63
E
5
1
1
2
3
4
11.3 CD CORE UNIT(S10.5COMP2-USB-C3)
C
A
SIDE A
PICKUP UNIT(P10.5) (SERVICE)
B
A
CN651
REFO1 F E
C
D
HOME
E
M2 LOADING/CARRIAGE MOTOR M1 SPINDLE MOTOR
F
C
1 2 3 4
5
6
7
8
C
SIDE B
A
8EJ 12EJ
B
DSCSNS
C
D
E
F
C
DEH-2100UB/XS/EW5
5 6 7 8
65
1
2
3
4
12. ELECTRICAL PARTS LIST
A
B
NOTE: Parts whose parts numbers are omitted are subject to being not supplied. T
he part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,R
S1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... Th
e > mark found on some component parts indicates the importance of the safety fa
ctor of the part. Therefore, when replacing, be sure to use parts of identical d
esignation. Meaning of the figures and others in the parentheses in the parts li
st. Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of
the corresponding PC board. IC 301 (A, 91, 111) IC NJM2068V The expression of t
he unit in this manual is shown by u instead of µ. Please do not make a mistake.
Circuit Symbol and No. Part No.
Q Q Q Q Q Q Q Q Q D D D D D D D D D D D D D D D D D D D L L L L L L L L L L L L
Circuit Symbol and No.
201 351 601 821 822 851 931 991 992 301 302 501 502 601 602 840 841 842 843 844
845 851 901 902 911 912 931 991 151 401 402 407 501 561 601 602 603 604 605 606
(B,131,130) Transistor (B,160,128) Transistor (A,150,68) Transistor (B,21,17) Tr
ansistor (B,21,12) Transistor (B,71,115) Transistor(A,B) (B,60,118) Transistor (
A,7,117) Transistor (B,12,107) Transistor (A,65,129) Diode (A,53,130) Diode (B,6
6,91) Diode (A,50,105) Diode (B,136,19) Diode(A,B) (B,128,15) Diode(A,B) (B,77,5
) Varistor (B,76,13) Varistor (B,33,12) Varistor (B,33,11) Varistor (B,80,4) Var
istor (B,78,16) Varistor (B,70,121) Diode(A,B) (A,53,124) Diode (A,53,127) Diode
(A,53,77) Diode (A,44,82) Diode (A,59,124) Diode (A,19,114) Diode (A,134,119) I
nductor (A,149,83) Inductor (A,147,94) Inductor (B,164,71) Inductor (A,68,94) In
ductor (B,42,91) Resistor (B,120,23) Inductor (A,148,25) (A,111,81) (A,119,68) (
A,127,70) (A,146,70) Inductor Inductor Inductor Inductor Inductor
Part No.
RT3T22M RT3N66M 2SD1858 2SA1036K LTC114EUB 2SA1036K LSC4081UB 2SD2396 RT3T22M 1S
R139-400 1SR139-400 RB060L-40 1SR139-400 RB551V-30 RB751V-40 EZJZ1V270RM EZJZ1V2
70RM EZJZ1V800AM EZJZ1V800AM EZJZ1V270RM EZJZ1V270RM MC2848-11 1SR139-400 1SR139
-400 1SR139-400 1SR139-400 HZS7L(A1) HZS7L(C3) LAU2R2K LAU2R2K LAU2R2K CTF1473 V
TL1118 RS1/10S0R0J CTF1389 LAUR47K LAU2R2K LAUR47K LAUR47K LAU1R0K
C
D
A:DEH-2100UB/XS/EW5 B:DEH-2120UB/XS/EW5 C:DEH-2110UB/XS/UR Unit Number : YWM5292
(A) Unit Number : YWM5317(B) Unit Number : YWM5316(C) Unit Name : Tuner Amp Unit
Unit Number : Unit Name : Keyboard Unit Unit Number : CWX3679 Unit Name : CD Co
re Unit(S10.5COMP2-USB-C3)
model
A:DEH-2100UB/XS/EW5 B:DEH-2120UB/XS/EW5 C:DEH-2110UB/XS/UR
E
A Number : YWM5292(A) Unit
Unit Number : YWM5317(B) Unit Number : YWM5316(C) Unit Name : Tuner Amp Unit
MISCELLANEOUS
IC 151 IC 251 IC 301 IC 501 IC 601 IC 911 (B,127,105) IC (B,69,87) IC (A,91,135)
IC (B,64,100) IC (B,128,45) IC (A,16,65) IC PML014A BD6538G PAL007C BD9007F PN5
024B BA49181-V12
F
66
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
L L L L L L L L L L L L L L L 607 608 609 610 611 612 613 614 615 616 617 618 61
9 801 851 (A,147,62) (A,134,70) (A,131,70) (A,144,67) (B,135,81) (B,133,81) (B,1
44,62) (B,123,62) (B,146,54) (B,151,76) Inductor Inductor Inductor Inductor Indu
ctor Inductor Inductor Inductor Inductor Inductor
Part No.
LAU1R0K LAU1R5K LAU1R5K LAU1R2J CTF1379 CTF1379 CTF1379 CTF1379 CTF1389 CTF1379
CTF1379 CTF1379 CTF1379 LAU2R2K LAU2R2K
R 513 R 520 R R R R R R R R R R R R R R R 601 602 606 607 608 609 610 611 612 61
3 615 616 617 618 619 (B,65,86) (B,75,97) (B,123,28) (B,106,41) (B,107,71) (B,13
6,25) (B,140,61) (B,106,48) (B,117,72) (B,138,72) (B,114,74) (B,141,53) (B,111,7
3) (B,154,40) (B,137,32) (B,147,42) (B,147,40) (B,130,28) (B,134,17) (B,134,17)
(B,126,14) (B,126,14) (B,159,94) (B,154,38) (B,36,27) (B,44,24) (B,31,29) (B,31,
34) (B,31,33) (B,31,31) (B,106,28) (B,106,30) (B,32,37) (B,106,32) (B,106,34) (B
,109,30) (B,109,32) (B,109,34) (B,19,41) (B,116,22) (B,149,56) (B,132,22) (B,132
,27) (C) (B,61,69) (B,58,77) (B,62,77) (B,17,36) (B,20,20) (B,26,18) (B,55,17) (
B,71,18) (A,75,28) (A,79,25) (B,64,34) (A,74,21) (B,71,20) (B,93,15) (B,93,17) (
B,74,116) (A,B) (B,70,119) (A,B)
Part No.
RS1/16S0R0J RS1/16S0R0J RS1/16S473J RS1/16S473J RS1/16S473J RAB4C104J RS1/16S470
J RS1/16S473J RS1/16S203J RS1/16S182J RS1/16S563J RS1/16S302J RS1/16S563J RS1/16
S104J RS1/16S473J RS1/16S473J RS1/16S104J RS1/16S104J RS1/16S103J RS1/16S104J RS
1/16S103J RS1/16S104J RS1/16S273J RS1/16S104J RS1/16S120J RS1/16S120J RS1/16S104
J RS1/16S102J RS1/16S102J RS1/16S221J RS1/16S104J RS1/16S104J RS1/16S104J RS1/16
S472J RS1/16S472J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S104J RS1/16S0R0J RS
1/16S103J RS1/16S473J RS1/16S273J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S222
J RS1/16S562J RS1/16S103J RS1/16S1R0J RS1/16S473J RD1/4PU222J RD1/4PU222J RS1/16
S104J RD1/4PU103J RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S472J RS1/16S472J
C A
(B,142,78) Inductor (B,127,23) Inductor (B,115,65) Inductor (A,15,39) Inductor (
A,65,131) Inductor(A,B)
B
L 901 X 601 X 602 FU351 AR401
(A,35,99) Choke Coil 600 uHCTH1280 (A,141,63) Oscillator 74.100 MHzCSS1749 (A,11
4,59) Oscillator 4.7186 MHz(C)CSS1727 (B,138,128) Fuse 3 A CEK1286 (B,164,117) S
urge ProtectorIMSA-6801-01Y901
R 622 R 623 R 624
RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 151 152 15
3 170 171 172 173 174 175 176 201 202 203 254 257 301 351 352 353 354 401 404 40
5 406 407 408 409 410 411 412 502 503 505 506 507 (B,115,97) (B,98,103) (B,123,9
3) (B,106,96) (B,141,101) (B,111,106) (B,144,104) (B,111,103) (B,144,99) (B,111,
104) (B,128,123) (B,121,135) (B,120,135) (B,74,88) (B,75,102) (B,83,108) (B,165,
132) (B,165,136) (B,157,125) (B,164,127) (B,158,45) (B,160,58) (B,160,55) (B,160
,61) (B,160,63) (B,170,56) (B,160,48) (B,160,50) (B,160,52) (B,160,54) (B,75,95)
(B,76,98) (B,73,91) (B,71,96) (B,113,37) (B,60,95) (B,59,92) (B,62,87) RS1/16S1
02J RS1/16S102J RS1/16S102J RS1/16S0R0J RS1/16S102J RS1/16S102J RS1/16S681J RS1/
16S681J RS1/16S223J RS1/16S223J RS1/16S103J RS1/16S153J RS1/16S221J RS1/16S561J
RS1/16S473J RS1/16S153J RS1/16S223J RS1/16S223J RS1/16S821J RS1/16S821J RS1/16S1
02J RS1/16S472J RS1/16S682J RS1/16S102J RS1/16S102J RAB4C104J RS1/16S391J RS1/16
S681J RS1/16S681J RS1/16S681J RS1/16S4702F RS1/16S562J RS1/16S1002F RS1/16S393J
RS1/16S222J RS1/16S513J RS1/16S392J RS1/10SR471J
(A,B) (C) (A,B) (C)
R 638 R 643 R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R
R R 645 646 651 652 653 654 656 657 658 659 660 661 662 663 664 665 666 670 671
757 758 759 803 821 822 831 832 833 834 836 837 838 839 840 851 852
D
E
F
R 508 R 509 R 511
DEH-2100UB/XS/EW5
5 6 7 8
67
1
2
3
4
R R R R R R R R R R 853 854 855 871 872 888 931 932 933 934 (B,68,124) (A,B) (B,
63,115) (A,B) (B,59,115) (B,123,134) (A,B) (B,128,124) (A,B) (B,76,4) (B,105,41)
(B,66,117) (A,59,126) (B,66,122) (B,66,119) (A,13,122)
Part No.
RS1/16S153J RS1/16S102J RS1/16S104J RS1/16S102J RS1/16S102J RS1/16S0R0J RS1/16S1
04J RS1/16S223J RD1/4PU102J RS1/16S472J RS1/16S473J RD1/4PU271J C C C C C C C C
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
C C C C C C C C C C C C C
604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 620 622 623 624 625
626 627 628 629 630 631 632 633 634 635 640 641 642 643 645 651 652 653 654 655
668 669 670 821 831 832 833 834 839 840 841 871 872 901 911 912 913 914 915 917
991
3
Part No.
CKSRYB103K50 CKSRYB104K16 CKSRYB103K50 CKSRYB103K50 CKSRYB103K50 CKSRYB331K50 CE
JQ101M6R3 CKSRYB331K50 CKSRYB103K50 CEAL101M6R3 CKSRYB102K50 CKSRYB331K50 CKSRYB
105K10 CKSRYB105K10 CCSRCH270J50 CKSRYB105K10 CKSRYB104K16 CKSRYB102K50 CKSRYB10
2K50 CCSRCH270J50 CCSRCH270J50 CCSRCH150J50 CKSRYB102K50 CCSRCH4R0C50 CCSRCH8R0D
50 CKSRYB223K50 CKSRYB104K16 CKSRYB104K16 CCSRCH270J50 CKSRYB104K16 CKSRYB103K50
CKSRYB104K16 CKSRYB122K50 CKSRYB122K50 CKSRYB103K50 CKSRYB102K50 CKSRYB221K50 C
CSRCH220J50 CKSRYB102K50 CKSRYB104K16 CKSRYB105K10 CKSRYB105K10 CKSRYB104K16 CKS
RYB104K16 CCSRCH221J50 CCSRCH221J50 CKSRYB104K16 CCSRCH221J50 CCSRCH221J50 CCSRC
H221J50 CCSRCH221J50 CKSRYB103K50 CKSRYB103K50 CCH1732 CEJQ100M16 CEAT102M16 CKS
RYB104K16 CEAT221M10 CEJQ100M16 CKSRYB104K16 CKSRYB473K25
4
A
(B,143,74) (B,108,74) (B,105,62) (B,117,56) (B,99,81) (B,114,73) (A,97,83) (B,11
4,71) (B,119,60) (A,103,59) (B,169,94) (B,123,61) (B,122,67) (B,129,62) (B,111,5
5) (C) (B,144,58) (B,141,55) (B,133,66) (B,131,67) (B,136,73) (B,130,73) (B,134,
79) (B,142,65) (B,135,60) (B,143,70) (B,108,72) (B,129,24) (B,142,31) (B,111,59)
(C) (B,145,55) (B,143,72) (B,123,59) (B,114,99) (B,141,97) (B,116,20) (B,22,27)
(B,47,36) (B,113,35) (B,27,42) (B,25,41) (B,128,78) (B,129,22) (B,140,79) (B,19
,14) (B,66,28) (B,66,27) (B,64,32) (B,64,30) (B,79,13) (B,73,25) (B,71,22) (B,13
0,138) (A,B) (B,130,132) (A,B) (A,46,115) 3 300 uF/16 V (A,58,63) (A,47,69) (B,2
8,73) (A,49,63) (A,54,51) (B,27,78) (B,10,109)
R 935 R 991
CAPACITORS
B
C C C C C C C C C C
C
151 152 153 154 155 158 161 164 165 170 171 172 201 251 301 302 303 304 305 306
307 308 309 310 312 313 353 354 359 401 404 405 406 409 411 412 501 502 504 505
506 508 601 602 603
(B,117,101) (B,141,99) (B,117,99) (B,138,98) (A,120,116) (B,117,103) (B,141,105)
(A,114,111) (B,123,116) (B,131,92) (B,138,103) (B,117,104) (A,132,135) (B,66,4)
(B,125,126) (B,121,124) (B,123,126) (B,118,124) (B,120,132) (B,118,129) (B,120,
131) (B,115,124) (B,120,140) (B,117,141) (A,103,123) (B,97,142) (A,154,121) (A,1
48,121) (B,164,138) (B,169,71) (A,B) (A,150,97) (B,148,101) (B,170,59) (B,158,46
) (B,162,45) (B,169,96) (A,60,89) 150 uF/6.3 V (A,56,94) (B,58,103) (B,71,98) (B
,71,99) (B,57,88) (B,119,27) (B,119,29) (B,122,28)
CKSRYB224K10 CKSRYB224K10 CKSRYB105K10 CKSRYB105K10 CEJQ470M10 CKSRYB105K10 CKSR
YB105K10 CEJQ100M16 CKSRYB104K16 CKSRYB104K16 CKSRYB105K10 CKSRYB105K10 CEJQ330M
10 CKSRYB105K10 CKSQYB474K25 CKSQYB474K25 CKSQYB474K25 CKSQYB474K25 CKSRYB474K16
CKSRYB474K16 CKSRYB474K16 CKSRYB474K16 CKSQYB225K10 CKSQYB225K10 CEJQ100M16 CKS
RYB104K16 CEJQ2R2M50 CEJQ2R2M50 CCSQCH102J50 CKSRYB104K16 CEJQ101M10 CKSRYB103K5
0 CCSRCH390J50 CCSRCH100D50 CCSRCH151J50 CKSRYB104K16 CCH1804 CEJQ221M16 CKSQYB2
25K16 CCSRCH101J50 CKSRYB153K50 CKSRYB105K10 CKSRYB105K10 CKSRYB103K50 CKSRYB103
K50
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
D
E
F
68
DEH-2100UB/XS/EW5
1 2
5
6
7
8
C 992 (A,12,97)
Part No.
CEJQ101M10
C 1807 (B,126,19)
Part No.
CKSRYB472K50
B Number : (A)(C) Unit
Unit Name : Keyboard Unit
MISCELLANEOUS
IC 1801 D 1801 D 1802 D 1803 D 1804 D D D D D D D D D D D D D D D D D D D D 1805
1806 1807 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1834 1835 1836 1837
1838 1839 1840 (B,100,20) IC (B,103,6) Diode (B,100,6) Diode (B,135,20) Varisto
r (B,128,18) Varistor (B,138,20) Varistor (B,139,26) Diode (B,141,27) Diode (A,1
39,22) White LED (A,6,13) LED (A,5,30) LED (A,15,28) LED (A,39,5) LED (A,24,19)
LED (A,16,13) LED (A,37,33) LED (A,52,18) LED (A,54,33) LED (A,91,8) LED (A,79,8
) LED (A,68,8) LED (A,103,8) LED (A,115,8) LED (A,127,8) LED (A,146,41) LED PD63
40A MC2848-11 MC2846-11 EZJZ1V270RM EZJZ1V270RM EZJZ1V270RM MALS068X MALS068X NE
SW505C-5273 CL-195SR-CD CL-195SR-CD CL-195SR-CD CL-195SR-CD CL-195SR-CD CL-195SR
-CD CL-195SR-CD CL-195SR-CD CL-195SR-CD CL-195SR-CD CL-195SR-CD CL-195SR-CD CL-1
95SR-CD CL-195SR-CD CL-195SR-CD CL-195SR-CD
B Number : (B) Unit
Unit Name : Keyboard Unit
MISCELLANEOUS
IC 1801 D 1801 D 1802 D 1803 D 1804 D D D D D D D D D D D D D D D D D D D D 1805
1806 1807 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 1834 1835 1836 1837
1838 1839 1840 (B,100,20) IC (B,103,6) Diode (B,100,6) Diode (B,135,20) Varisto
r (B,128,18) Varistor (B,138,20) Varistor (B,139,26) Diode (B,141,27) Diode (A,1
39,22) White LED (A,6,13) LED (A,5,30) LED (A,15,28) LED (A,39,5) LED (A,24,19)
LED (A,16,13) LED (A,37,33) LED (A,52,18) LED (A,54,33) LED (A,91,8) LED (A,79,8
) LED (A,68,8) LED (A,103,8) LED (A,115,8) LED (A,127,8) LED (A,146,41) LED PD63
40A MC2848-11 MC2846-11 EZJZ1V270RM EZJZ1V270RM EZJZ1V270RM MALS068X MALS068X NE
SW505C-5273 CL-195PG-CD CL-195PG-CD CL-195PG-CD CL-195PG-CD CL-195PG-CD CL-195PG
-CD CL-195PG-CD CL-195PG-CD CL-195PG-CD CL-195PG-CD CL-195PG-CD CL-195PG-CD CL-1
95PG-CD CL-195PG-CD CL-195PG-CD CL-195PG-CD
A
B
C
L 1801 X 1801 S 1833 LCD1801
(B,137,26) Inductor CTF1713 (B,92,8) Ceramic Resonator 5.00 MHzCSS1731 (A,38,19)
Rotary Switch CSD1153 (A,133,32) LCD CAW1970
L 1801 X 1801 S 1833 LCD1801
(B,137,26) Inductor CTF1713 (B,92,8) Ceramic Resonator 5.00 MHzCSS1731 (A,38,19)
Rotary Switch CSD1153 (A,133,32) LCD CAW1970
D
RESISTORS
R R R R R R R R R R 1801 1806 1807 1809 1810 1811 1812 1813 1814 1815 (B,102,10)
(B,133,19) (B,134,14) (B,57,28) (B,138,23) (B,13,20) (B,13,14) (B,16,30) (B,73,
18) (B,123,8) (B,87,6) (B,87,9) (B,21,16) RS1/16S473J RS1/16S101J RS1/16S101J RS
1/16S473J RS1/4SA821J RS1/4SA821J RS1/4SA821J RS1/4SA821J RS1/4SA821J RS1/4SA681
J RS1/16S222J RS1/16S222J RS1/16S0R0J
RESISTORS
R R R R R R R R R R 1801 1806 1807 1809 1810 1811 1812 1813 1814 1815 (B,102,10)
(B,133,19) (B,134,14) (B,57,28) (B,138,23) (B,13,20) (B,13,14) (B,16,30) (B,73,
18) (B,123,8) (B,87,6) (B,87,9) (B,21,16) RS1/16S473J RS1/16S101J RS1/16S101J RS
1/16S473J RS1/4SA821J RS1/4SA561J RS1/4SA561J RS1/4SA561J RS1/4SA561J RS1/4SA391
J RS1/16S222J RS1/16S222J RS1/16S0R0J
E
R 1828 R 1829 R 1839
R 1828 R 1829 R 1839
CAPACITORS
C C C C C 1802 1803 1804 1805 1806 (B,119,19) (B,130,18) (B,133,17) (B,136,20) (
B,139,20) CKSRYB105K10 CKSRYB472K50 CKSRYB472K50 CKSRYB472K50 CKSRYB472K50
CAPACITORS
C C C C C 1802 1803 1804 1805 1806 (B,119,19) (B,130,18) (B,133,17) (B,136,20) (
B,139,20) CKSRYB105K10 CKSRYB472K50 CKSRYB472K50 CKSRYB472K50 CKSRYB472K50
F
DEH-2100UB/XS/EW5
5 6 7 8
69
1
2
3
4
C 1807 (B,126,19)
Part No.
CKSRYB472K50 R R R R R R R R R R R R R R R R R R R
282 283 284 285 290 291 294 307 308 309 310 601 602 606 701 702 708 712 713 (A,3
0,61) (A,29,61) (B,29,63) (B,28,63) (B,24,43) (B,42,62) (A,31,62) (A,35,19) (A,3
7,19) (A,35,21) (A,37,22) (B,30,31) (B,27,31) (B,28,23) (B,11,37) (A,23,56) (B,1
5,37) (B,14,54) (B,14,53)
Part No.
RS1/16SS120J RS1/16SS120J RS1/16SS153J RS1/16SS153J RS1/16SS103J RS1/16SS272J RS
1/16SS471J RS1/16SS183J RS1/16SS183J RS1/16SS183J RS1/16SS183J RS1/16SS0R0J RS1/
16SS0R0J RS1/16S0R0J RS1/16SS221J RS1/16SS221J RS1/16S0R0J RS1/16SS0R0J RS1/16SS
0R0J
A
C Number : CWX3679 Unit
Unit Name : CD Core Unit(S10.5COMP2-USB-C3)
MISCELLANEOUS
IC 201 IC 301 Q 101 Q 102 X 201 (A,35,46) (A,28,15) (B,58,69) (B,48,58) (A,22,37
) (B,33,63) (A,55,37) (B,19,58) (B,40,68) (B,25,69) IC PE5666A IC BA5839FP Trans
istor 2SA1577 Chip Transistor 2SB1689 Ceramic Resonator 16.934 MHz CSS1603 Oscil
lator 48.000 MHz CSS1753 Switch(HOME) CSN1067 Switch(DSCSNS) CSN1067 Switch(12EJ
) CSN1068 Switch(8EJ) CSN1068
B
X S S S S
205 901 903 904 905
RESISTORS CAPACITORS
R R R R R
C
101 102 103 104 105 107 202 203 204 206 209 210 214 216 221 222 223 225 226 227
228 229 230 232 233 234 235 237 240 241 244 249 254 255 256 259 261 262 263 280
(B,61,74) (B,61,72) (B,61,71) (B,53,66) (B,44,57) (B,52,60) (A,27,32) (A,51,44)
(A,23,58) (B,10,26) (B,18,52) (B,10,23) (B,49,50) (B,48,49) (A,51,48) (A,51,46)
(B,13,43) (A,50,50) (A,50,51) (B,47,51) (B,44,51) (B,46,53) (B,21,25) (B,45,51)
(B,26,59) (B,22,26) (A,26,59) (A,24,35) (B,14,26) (B,13,25) (B,22,55) (B,14,50)
(A,25,64) (A,26,63) (A,25,62) (A,27,66) (A,26,65) (A,29,59) (A,27,63) (B,20,45)
RS1/10SR2R4J RS1/10SR2R4J RS1/10SR2R7J RS1/16SS222J RS1/16SS102J RS1/16SS105J RS
1/16SS473J RS1/16S473J RS1/16SS221J RS1/16SS104J RS1/16SS103J RS1/16SS102J RS1/1
6SS472J RS1/16SS472J RS1/16SS103J RS1/16SS103J RS1/16SS473J RS1/16SS103J RS1/16S
S393J RS1/16SS562J RS1/16SS122J RS1/16SS472J RS1/16SS0R0J RS1/16SS122J RS1/16SS1
03J RS1/16SS473J RS1/16SS473J RS1/16SS151J RS1/16S473J RS1/16SS103J RS1/16SS473J
RS1/16SS103J RS1/16SS104J RS1/16SS104J RS1/16SS104J RS1/16SS0R0J RS1/16SS104J R
S1/16SS0R0J RS1/16SS0R0J RS1/16SS103J
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C
106 202 204 205 206 207 209 210 211 212 213 214 216 217 218 219 220 221 222 223
224 226 227 228 229 236 239 240 243 250 251 260 261 262 293 303 304 307 308
(B,56,67) (A,28,57) (A,23,59) (B,27,41) (A,23,40) (A,24,37) (B,35,34) (B,29,37)
(A,28,35) (A,28,30) (A,46,39) (A,29,33) (A,51,52) (A,48,51) (A,50,52) (A,47,53)
(A,48,53) (A,46,54) (B,45,53) (B,47,53) (A,44,55) (A,42,59) (A,42,61) (B,41,61)
(B,48,60) (A,49,58) (B,46,51) (A,38,61) (B,22,41) (A,52,48) (A,52,46) (A,28,61)
(B,33,66) (B,31,66) (B,43,61) (A,36,19) (A,36,21) (A,22,11) (B,11,18)
CKSQYB475K10 CKSSYB104K10 CKSSYB103K16 CKSQYB475K10 CKSSYB104K10 CKSRYB104K16 CE
VW220M6R3 CKSSYB104K10 CKSSYB104K10 CKSRYB104K16 CKSSYB104K10 CKSSYB104K10 CKSSY
B332K50 CKSSYB104K10 CKSSYB473K10 CKSSYB104K10 CKSSYB182K50 CKSSYB104K10 CCSSCH5
60J50 CCSSCH4R0C50 CKSSYB104K10 CCSSCH680J50 CCSSCH470J50 CKSSYB103K16 CKSSYB104
K10 CKSSYB104K10 CCSSCH220J50 CKSSYB104K10 CKSQYB475K103 CKSSYB102K50 CKSSYB102K
50 CKSSYB104K10 CCSSCH8R0D50 CCSSCH8R0D50 CKSSYB102K50 CKSSYB472K25 CKSSYB223K16
CKSRYB104K16 CKSRYB105K10
R R R R R R R R R R
D
R R R R R R R R R R
E
R R R R R R R R R R R R R R R
F
70
DEH-2100UB/XS/EW5
1 2 3 4
5
6
7
8
C 703 C 704 C 711 (B,14,35) (B,11,36) (A,31,25)
Part No.
CCSSCH101J50 CKSSYB102K50 CKSSYB104K10
A
Miscellaneous Parts List
M 1 M 2 Pickup Unit(P10.5)(Service) CXX1942 Motor Unit(SPINDLE) CXC7134 Motor Un
it(LOADING/CARRIAGE) CXC4026
B
C
D
E
F
DEH-2100UB/XS/EW5
5 6 7 8
71

Pioneer Deh 2100ub 2110ub 2120ub

Uploaded by

Copyright:

Available Formats

Pioneer Deh 2100ub 2110ub 2120ub

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pioneer Deh 2100ub 2110ub 2120ub

Uploaded by

Copyright:

Available Formats

ORDER NO.

You might also like