MATERIAL SAFETY DATA SHEET

SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Chemical Name And Synonyms Chemical Family Trade Name & Synonyms C.A.S. No. Formula Manufacturer's Name Address Emergency Telephone No : : : : : : : : Polypropylene Copolymer Polyolefin Repol 9010 - 79 - 1 ( CH -CH2) n | CH3 Reliance Industries Limited Product Application & Research Centre V N Purav Marg, Chembur, Mumbai - 400071, India 91-22-30515000

SECTION 2 - COMPOSITION / INFORMATION ON INGREDIENTS

Paints Preservatives & Solvents Alloys & Metallic Coatings NIL Pigments Base metal 0.01 Catalyst Alloys NIL Vehicle Metallic coatings NIL Solvents Filler Metal plus coating or core flux <1 NA Additives Others Hazardous Mixtures of Other Liquids, Solids or Gases % TLV (units) NA NA NA NA % NIL NIL NIL NIL NIL NIL TLV (units) NA NA NA NA NA NA

REPOL polypropylene resins are not considered to be hazardous under normal processing conditions

SECTION 3 - HAZARDS IDENTIFICATION

POTENTIAL HEALTH EFFECTS EYE CONTACT Particulate may scratch eye surfaces / cause mechanical irritation SKIN CONTACT Negligible hazard at ambient temperatures (-18 to + 50 C; 0 to 100 F). Exposure to hot material may cause thermal burns INHALATION Negligible hazard at ambient temperatures (-18 to + 50 C; 0 to 100 F). Vapors that may be formed at elevated temperatures may be irritating to eyes and respiratory tract INGESTION Not toxic

Page 1 of 1

MATERIAL SAFETY DATA SHEET

SECTION 4 - FIRST AID MEASURES

EYE CONTACT This product is an inert solid. If in eye, remove as one would any foreign object SKIN CONTACT In case of adverse exposure to hot material, immediately immerse in or flush the affected area with large amounts of cold water to dissipate heat. Cover with clean cotton sheeting and get prompt medical attention. No attempt should be made to remove material from skin or to remove contaminated clothing, as the damaged flesh can be easily torn. INHALATION In case of adverse exposure to vapors formed at elevated temperatures, immediately remove the affected victim from exposure. Administer artificial respiration if breathing is stopped. Keep at rest. Call for prompt medical attention. INGESTION First aid is normally not required

SECTION 5 - FIRE FIGHTING MEASURES

Flash Ignition Temperature - 345 C Auto Ignition Temperature - 360 C Flammable limits Extinguishing Media N/A Water, Dry Chemical, Co2, Foam LEL UEL N/A N/A

Special Fire Fighting Procedures: Repol resins are combustible materials - molten polypropylene tends to flow or drip and will propagate fire. Respiratory and eye protection required for fire fighting personnel Unusual Fire and Explosion Hazards : Failure or malfunction of temperature control systems on processing equipment such as extruders may create explosion hazard

SECTION 6 - ACCIDENTAL RELEASE MEASURES

LAND SPILL Recover spilled material and place in suitable containers for recycle or disposal. Pellets released or spilled during shipping or storage may create a slipping hazard and should be removed from walkways. Consult an expert on disposal of recovered material and ensure conformity to local regulations.

SECTION 7 - STORAGE AND HANDLING

Storage Temperature,C : Ambient Loading / Un-Loading Temperature, C : Ambient Storage / Transport Pressure, mm Hg : Atmospheric Loading / Un-Loading Viscosity, cSt : Solid Storage and Handling : Store in a cool, well ventilated place away from incompatible materials. DO NOT handle or store near an open flame, heat or other sources of ignition. Protect material from direct sunlight. Material will accumulate static charges that may cause an electrical spark (ignition source). Use proper grounding procedures.

Page 2 of 2

MATERIAL SAFETY DATA SHEET

SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Respiratory Protection (Specify type) : NONE Special -Ventilation Local Exhaust recommended for high temperature processing Mechanical (General) -Other -Protective Gloves : Use gloves when handling hot melt Eye Protection : Use goggles when handling hot melt Other Protective Equipment : Long sleeve shirts & long cotton pants to protect skin contact with hot melt

SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES

N/A Specific Gravity (H2O=1) Boiling Point (C) N/A Vapour Pressure (mm Hg.) Percent Volatile by volume (%) N/A Vapour Density, at 1 atm (Air=1) Evaporation Rate Insoluble Solubility in water Appearance and odour: White Pellets, No Specific Odour 0.90 <0.1 N/A

SECTION 10 - STABILITY AND REACTIVITY

Unstable Conditions to avoid Stable Heating above 350c, direct flame Incompatibility (materials to avoid): Strong oxidants at high temperature Hazardous decomposition products CO, CO2, HYDROCARBONS, SMOKE, ACROLEIN * Hazardous Polymerisation May occur Conditions to avoid NA Will not occur Stability * Decomposition products may vary in nature depending upon actual conditions; e.g. availability of oxygen; temperature and presence of other materials

SECTION 11 - TOXICOLOGICAL INFORMATION

Please refer to Section 3 for available information on potential health effects

SECTION 12 - ECOLOGICAL INFORMATION

No specific ecological data are available for this product. Please refer to Section 6 for information regarding accidental releases and Section 15 for regulatory reporting information.

Page 3 of 3

MATERIAL SAFETY DATA SHEET

SECTION 13 - DISPOSAL CONSIDERATIONS
Waste disposal method: Landfill Or Incineration. Please refer to Sections 5,6 and 15 for disposal and regulatory information.

SECTION 14 - TRANSPORT INFORMATION

Not applicable, This product is not transport regulated

SECTION 15 - REGULATORY INFORMATION

Product meets the requirements stipulated in IS 10910 on Specification for polypropylene and its copolymers for safe use in contact with foodstuffs, pharmaceuticals and drinking water. Additives incorporated in this grade conform to the positive list of constituents as prescribed in IS 10909. The product and the additives incorporated in it also comply with the FDA: CFR Title 21, 177.1520 Olefin polymer.

SECTION 16 - OTHER INFORMATION

Ecotoxicity Persistence MANUFACTURER'S DATA: REGD. OFFICE : RELIANCE INDUSTRIES LIMITED RELIANCE CENTRE BALLARD ESTATE, W.H.MARG MUMBAI - 400 038 TEL : 022-30324000 FAX : 022-30327399 MANUFACTURING PLANT : RELIANCE INDUSTRIES LIMITED HAZIRA MANUFACTURING DIVISION, SURAT-HAZIRA ROAD, VIL. MORA, P.O. BHATHA - SURAT, GUJARAT - 394 510 TEL : 0261-3035999 FAX : 0261-3035444 MANUFACTURING PLANT : RELIANCE INDUSTRIES LIMITED VILLAGE MOTI KHAVDI, POST DIGVIJAYGRAM, DIST. JAMNAGAR, GUJARAT - 361 140 TEL. 0288-3012929 REVISION SUMMARY: Since October 22, 2002 this MSDS has been revised
Disclaimer: This information relates to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. Information contained in this Material Safety Data Sheet is to the best of our knowledge and believed to be reliable but no representation, guarantee or warranties of any kind are made as to its accuracy, suitability for a particular application etc. It is upto the user / distributor to ensure that the information contained in the material safety data sheet is relevant to the product manufactured or sold as the case may be. Reliance Industries Limited and Reliance Group of Companies makes no warranties, expressed or implied, in respect of the adequacy of this document for any particular purpose.

: :

Not toxic under normal conditions Non-biodegradable

Page 4 of 4