Uttar Pradesh Pollution Control Board

Building. No TC-12V Vibhuti Khand, Gomti Nagar, Lucknow-226010

Phone:0522-2720828,2720831, Fax:0522-2720764, Email: info@uppcb.com, Website: www.uppcb.com

______________________________________________________________________________________
159911/UPPCB/GreaterNoida(UPPCBRO)/CTO/both/GREATER NOIDA/2022 Date: 16/07/2022
To,
M/s
SANDHU CONSTRUCTION EQUIPMENT AND SERVICE
KHASRA NO.-123, KHATA NO.-00009, VILLAGE- AIMNABAD, POST- BISRAKH, SECTOR-
1,GREATER NOIDA ,GAUTAM BUDDHA NAGAR,20306

Consolidated Consent to Operate and Authorisation hereinafter referred to as the CCA (Consolidated
Consent & authorization) (Fresh) under Section-25 of the Water (Prevention & Control of Pollution)
Act, 1974 and under Section-21 of the Air (Prevention & Control of Pollution) Act, 1981

Consent No-17001228 Date-16/07/2022

CCA is hereby granted to SANDHU CONSTRUCTION EQUIPMENT AND SERVICE located at

KHASRA NO.-123, KHATA NO.-00009, VILLAGE- AIMNABAD, POST- BISRAKH, SECTOR-
1,GREATER NOIDA ,GAUTAM BUDDHA NAGAR,20306. subject to the provisions of the Water Act,
Air Act and the orders that may be made further and subject to following terms and conditions :-
1.This CCA SANDHU CONSTRUCTION EQUIPMENT AND SERVICE granted for the period from
03/07/2022 to 31/03/2025 and valid for manufacturing of following products with Capital Investment/Net
Assets Values 83.5621338 Lakhs

S Product Quantity Unit

No
1 Ready Mix Concrete 30 Cubic Meters/Hour
2. Specific Conditions under Water Act :-

(i) The daily quantity of effluent discharge (KLD) :-

Kind of Effulant Quantity(KLD) Treatment facility and

discharge point
Domestic 0.3 Septic Tank

(ii)Trade Effluent Treatment and Disposal :-The applicant shall operate Effluent Treatment Plant
consisting of primary/secondary and tertiary treatment as is required with reference to influent quantity and
quality.
In case of stoppage of functioning of ETP, production has to be stopped immediately and this Board has to
be intimated by fax/phone/email with a report in this regard to be dispatched immediately.

(iii)The treated effluent shall be recycled to the maximum extent and should be reused within the premises
for gardening etc. Quality of the treated effluent shall meet to the following general and specific standards as
prescribed under Environment (Protection) Rules, 1986 and applicable to the unit from time-to-time :-
 Industrial Effluent Quality Standard
S.No. Parameter Standard
1 NA NA
(iv)Sewage Treatment and Disposal :- The applicant shall provide comprehensive STP as is required with
reference to influent quantity and quality.In case of stoppage of functioning of STP, production has to be
stopped immediately and this Board has to be intimated by fax/phone/email with a report in this regard to be
dispatched immediately.

(v)The treated sewage shall be reused in gardening and the same shall be maintained continuously so as to
achieve the quality of the treated effluent to the following standards.

S No. Parameters Standards

1 Remarks NA
3. Conditions under Air Act :-

i)The applicant shall use following fuel and install a comprehensive control system consisting of control
equipment as is required with reference to generation of emissions and operate and maintain the same
continuously so as to achieve the level of pollutants to the following standards

Air Pollution Source Details

S No. Air Type of fuel Stack no Control Height of
Pollution Device Stack
Source
1 DG Set Diesel 1 Particulate 2.5 meter
1X45 KVA Matter above rooftop

Emmission Quality Standards

S No. Stack no Parameters Standards
1 1 Particulate Matter 0.3 g/kW-hr
2 1 Oxides of Nitrogen 4.7 g/kW-hr
3 1 Quantity of 3.5 g/kW-hr for CO
Emission
In case of stoppage of functioning of air pollution control equipment, production has to be stopped
immediately and this Board has to be intimated by fax/phone/email with a report in this regard to be
dispatched immediately
ii)Noise from the D.G. Set and other source(s) should be controlled by providing an acoustic enclosure as is
required for meeting the ambient noise standards for night and day time as prescribed for respective
areas/zones (Industrial, Commercial, Residential, Silence) which are as follows :-
Day time : from 6.00 a.m. to 10.00 p.m., Night time: from 10.00 p.m. to 6.00 a.m.
(iii) The unit will not use any type of restricted fuel.

Standards for Industrial Commercial Residential Silence

Noise level in Area Area Area Zone
db(A) Leq
Day Night Day Night Day Night Day Night
Time Time Time Time Time Time Time Time
75 70 65 55 55 45 50 40
6. Compulsory documents to be submitted by the Industry/Unit :-
(i)Annual return in Form-4 and Waste Disposal Manifest in Form-10 under Hazardous and Other Wastes
(Management and Transboundary Movement) Rules, 2016 and Third Party Audit Report.
(ii)Environment Statement in Form-V of Environment (Protection) Rules, 1986.
(iii)Quarterly compliance report of the CCA, photograph of ETP/APCs/Waste Storage Area.
7.Unit has to apply for renewal of CCA well in advance of 60 days of expiry of this CCA.
8.Competent Authority reserves the right to change/modify/add any time any condition of this CCA.
9.Unit has to comply with the other general conditions as annexed herewith. Non compliance of any
provision of this CCA and provisions of the Water Act, Air Act and Hazardous and Other Wastes
(Management and Transboundary Movement) Rules, 2016 will results in legal action under the aforesaid
Acts and Rules.
10.In compliance to the G.O dated 1011/81-7-2021-09 (Writ)/2016 dt.13.10.2021 issued by Department of
Environment, Forest and Climate Change, Uttar Pradesh. You are directed to develop Miyawaki Forest as
per the SOP available at URL:-http://www.upecp.in/TrainingSession.aspx for ensuring timely compliance of
this direction, you are hereby directed to submit a bank guarantee with minimum validity of one year of the
amount equivalent to the sum of initial consent fees (Air and Water) or Rs. 50,000/- (Rs. Fifty Thousand
Only) whichever is more, within 30 days from the date of issuance of this certificate. In case of non-
compliance of this direction, your consent shall be revoked by the Board.
11.The industry will have to obtain No objection certificate for abstraction of ground water. It will be the
responsibility of the industry to comply with the various conditions of the NOC obtained from the
competent authority and submit to the Board, within 3 months time failing which CTO shall be revoked.
BHUVAN Digitally signed by
BHUVAN PRAKASH
PRAKASH YADAV

YADAV
Date: 2022.07.16
19:11:22 +05'30'
Regional Officer

Copy to:

Chief Environmental Officer, (Circle–1), U.P. Pollution Control Board, Lucknow

BHUVAN Digitally signed by
BHUVAN
PRAKASH PRAKASH YADAV
Date: 2022.07.16
YADAV 19:11:39 +05'30'

Regional Officer

Annexure

Specific Conditions
1.This CTO is valid for production only in conforming zone.
2.No water and air pollution source will be added/ installed by the unit without prior permission from State
Pollution Control Board.
3.The unit is not allowed to increase the electricity load without prior permission from State Pollution
Control Board.
4.According to the affidavit sent by the RMC plant, the boundary wall of the tin shed should be constructed
on the side of the population located in front of the premises, so that the nearby residents do not have the
problem of dust.
5.Affidavit dated 28.06.2022 sent by RMC Plant should be followed in letter and spirit.
6.Installation of ducting and water sprinklers of adequate capacity to prevent dust emissions generated
during RMC plant operation, so that the environment is not adversely affected.
7.About 20 feet high sheets should be installed on the boundary of RMC and intensive plantation should be
done along the boundary.
8.Industrial effluents should not be disposed off by RMC Plant.
9.STP treated effluent should be used for production process, mixer washing and water sprinkling in RMC
plant.
10.The raw material should be stored inside the covered shed.
11.An effective system should be established to control the dust generated at the time of unloading of raw
materials.
12.Covered conveyor belt should be used for raw material feeding.
13.Continuous water sprinkling should be done to control the dust generated by vehicles coming on the
road.
14.Disposal of solid waste material should be done properly, so that the environment is not adversely
affected.
15.The floor in the RMC area should be made concrete, so that the dust does not fly into the atmosphere.
16.Extraction of ground water through any mechanism like bore well etc. is not allowed without prior
Registration/Permission from UP Ground Water Department (UPGWD).
17.The industry should ensure compliance of orders/instructions issued by Commission for Air Quality
Management Adjoining Areas (CAQM&AA) from time to time.
18.Industry shall submit quarterly monitoring reports of all stacks and ambient air quality from a
certified/approved laboratory.
19.DG sets should be operated on hybrid/dual fuel mode/retrofitment as per direction dt. 08.02.2022 of
Commission for Air Quality Management in National Capital Region And Adjoining Areas (CAQM&AA).
The link of order is https://caqm.nic.in/WriteReadData/RTF/Direction%20No.55%20(UP)3370f6d2-eefa-
49a8-9b6c-7455bebc6196.pdf.
20.Industry shall comply with various Waste Management Rules as notified by MoEf&CC i.e. Plastic Waste
Management Rules, 2016, Solid Waste Management Rules, 2016, Hazardous and Other Wastes
(Management and Transboundary) Rules, 2016, E-waste (Management) Rules, 2016, Construction and
Demolition Waste Management Rules, 2016.
21.Industry shall submit annual returns as per above mentioned rules. Also, Environmental Statement in
prescribed form as per Rule 14 of Environment (Protection) Act, 1986.
22.This consent is valid only for products and quantity mentioned above. Industry shall obtain prior
approval before making any modification in product/process/discharge/plant machinery failing which
consent would be deemed void.
23.Industry shall make rain water harvesting on the premises as per map approved by concerned Authority.
Pre-monsoon and Post- monsoon maintenance of rain water harvesting pit shall be done annually.
24.For green belt at least 8 feet height plants should be planted which shall be properly protected as proper
irrigation and manoeuvring arrangements shall be made. Industry shall develop green belt in accordance
with Government Order 07/55-02- 2018/09(writ)/2016 dated 26/02/2018 and UPPCB Office order issued
vide letter no. H16405/220/2018/02 dated 16/02/2018.
25.Industry shall ensure carbon offsetting as per Government Order (Environment Department) issued vide
letter no. H17259/ 183/55-2-2018/09(writ)/2016 dated 15.03.2018
26.Industry shall ensure compliance of CPCB Directions dated 02.07.2019 issued u/s 18(1)(b) of Air Act,
1981 and direction issued by Commission for air quality management letter no. A110013/09/2020/CAQM-
IP/648 dated 12.08.2021, regarding conversion of industrial units in NCR to PNG. In case of non
availability of gas, the unit has to upgrade its Air Pollution Control System (APCS) to bag filter/house or to
ESP for betterment of environment till the gas is available.
27.In case of violation of above-mentioned conditions or any public complaint, the consent may be
withdrawn.
General Conditions:-
The applicant shall get analyse the samples of effluent/emission/hazardous wastes at least once in a three
month from the laboratory recognized by the MoEF and shall report to the UEPPCB.
1.The applicant shall however, not without the prior consent of the Board bring into use any new or altered
outlet for the discharge of effluent or gases emission or sewage waste from the unit.
2.Treated waste water and domestic waste water shall be disposed jointly at one disposal point. The
applicant shall provide discharge measurement equipment at final disposal point.
3.The applicant shall strictly comply with conditions of this CCA and submit compliance report of stipulated
conditions within 30 days of receipt of this CCA. If, at any point of time, it is found that the industry is not
complying with stipulated conditions or any further direction/instruction issued by the Board, legal action
shall be initiated against the applicant.
4.The applicant shall maintain good house keeping. All valves/pipes/sewer/drains etc. must be leak-proof
5.The industry shall provide uninterrupted entry to the STPs/ETPs inlet and outlet points, Air Pollution
Control equipment and stack for smooth sampling/monitoring of efficiency of pollution control measures.
6.The industry shall provide Inspection Book at the time of inspection to the Board's officials.
7.Whenever due to any accident or other unforeseen act or event, such emission occurs or is apprehended to
occur in excess of standards laid down, such information shall be reported to the Board's offices and all
other concerned offices. In case of failure of pollution control equipment, the production process connected
to it shall be stopped with immediate effect.
8.The industry shall operate in a manner so that all emissions be emitted through designated chimney/stack
only.
9.In case of any damage to the agriculture productivity, human habitation etc. by the operation of industry, it
shall be imperative to stop production in the industry with immediate effect and such information shall be
reported to Board's offices. The industry shall be liable to pay compensation also in such cases as decided by
the Competent Authority.
10.The applicant shall apply before the 60 days of expiry of CCA or any change in production types/
production capacity/manufacturing process/capacity enhancement etc. or any change in effluent discharge
point or emission point
11.The Board reserves the right to revoke/add/modify any stipulated condition issued along with CCA, as
may be necessary.
12.The person authorized shall not rent, lend, sell, transfer or otherwise transport the hazardous waste
without obtaining prior permission of the Board.
13.Any unauthorized change in personnel, equipment as working condition as mentioned in the application
by the person authorized shall constitute a breach of his authorization.
14.It is the duty of the authorized person to take prior permission of the Board to close down the facility.
15.The authorization is valid for temporary storage of Hazardous Waste within premises only.
16.The authorized agency shall ensure that on-line data with regard to quantity and nature of hazardous
chemicals being used in the plant as well as air emission and waste generated within premises is displayed
on Display Board of size 6x4 feet outside the main factory gate within premises
17.It is duty of the authorized person to take prior permission of this Board to close and cleanup the facility
for treatment, storage and disposal of hazardous waste.
18.The applicant shall maintain record of hazardous waste in Form-3 and shall submit annual return in
Form-4 on or before the 30th day of June following to the financial year to which that return relates.
19.In no case any hazardous waste shall be disposed off on land, in any drain, or into any water stream. All
spillage must also be safely collected and stored.
20.Before the hazardous waste is stored or dumped in the facility, applicant must conduct a detailed physical
and chemical analysis of hazardous waste sample and report to the Board.
21.Dried hazardous sludge from the process in the plant shall be stored in double lined HDPE pit
constructed with R.C.C. or such material which does not react with the waste contained in it.
22.The storage area should be fenced properly and Sign/Notice Board indicating �Danger� and
�Hazardous� shall be displayed at appropriate position both in Hindi and English.
23.The industry shall store non-ferrous metal waste, used oil/spent oil waste in sealed drums placed on
impervious floor under covered shed. Hazardous waste if required shall be sold only to Registered
Recyclers/Re-processors.
24.In case of any transportation of hazardous waste, the details in Form-10 of the Hazardous and Other
Wastes Rules, 2016 shall be submitted to the Board.
BHUVAN Digitally
by BHUVAN
signed

PRAKASH PRAKASH YADAV

Date: 2022.07.16
YADAV 19:11:54 +05'30'
Regional Officer