Manual Toshiba Satellite
Manual Toshiba Satellite
Manual Toshiba Satellite
Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273
For more information, see If Something Goes Wrong on page 165 in this guide. Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
PMAD00007011 08/04
2
Models: Satellite A60/A65 Series ReWritable CD/DVD Drives
The computer system you purchased may include a ReWritable CD and/or DVD drive(s), among the most advanced data storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed. If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS (TOSHIBA), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA OR REMOVABLE STORAGE MEDIA ARISING OUT OF OR RESULTING FROM THE USE OF THE PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY THEREOF.
Critical Applications
The computer you have purchased is not designed for any critical applications. Critical applications means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage. ACCORDINGLY, TOSHIBA, ITS AFFILIATES AND SUPPLIERS DISCLAIM ANY AND ALL LIABILITY ARISING OUT OF THE USE OF THE COMPUTER PRODUCTS IN ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER PRODUCTS IN A
3
CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE.
NOTE
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, monitor port, USB port, PS/2 port, i.LINK port and microphone jack. Changes or modifications made to this equipment not expressly approved by Toshiba or parties authorized by Toshiba could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.
4
Contact: Toshiba America Information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000
FCC requirements
The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems. This equipment complies with Part 68 of the FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, the information must be provided to the telephone company. The modem connects to the telephone line by means of a standard jack called the USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC part 68 rules and requirements adopted by the ACTA. It is designed to be connected to a compatible modular jack that is also compliant. The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by the ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
5
Telephone Company Procedures
The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice, in writing, to allow you to make any changes necessary to maintain uninterrupted service.
If Problems Arise
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advanced notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
Disconnection
If you should ever decide to permanently disconnect your modem from its present line, please call the telephone company and let them know of this change.
Fax Branding
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including Fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.) In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer.
6
Alarm Equipment
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
7
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Wireless Interoperability
The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to:
The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined and approved by the Institute of Electrical and Electronics Engineers. The Wireless Fidelity (Wi-Fi) certification as defined by the Wi-Fi Alliance. The Wi-Fi CERTIFIED logo is a certification mark of the Wi-Fi Alliance. Bluetooth and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection. If you should experience any such problem, immediately turn off your Bluetooth or Wireless LAN device. Please contact Toshiba PC product support on Web site http://www.toshibaeurope.com/computers/tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for more information.
This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.85 GHz frequency range.
8
Wireless LAN and your Health
Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
Using the Wireless LAN equipment on board of airplanes, or In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the Wireless LAN device prior to turning on the equipment.
Regulatory Information
The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturers instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
9
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device. Lutilisation de ce dispositif est autorise seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) lutilisateur du dispositif doit tre prt accepter tout brouillage radiolectrique reu, mme si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term IC before the equipment certification number only signifies that the Industry Canada technical specifications were met. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Pour empecher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit etre utilize a l'interieur et devrait etre place loin des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d'emission) est installe a l'exterieur, il doit faire l'objet d'une licence. This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. Industry Canada requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC with essential test suites as per standards: EN 60950 Safety of Information Technology equipment ETS 300 328 Technical requirements for radio equipment ETS 300 826 General EMC requirements for radio equipment. English: Hereby, TOSHIBA Corp. Digital Media Network Company, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
10
Finnish: Valmistaja TOSHIBA Corp. Digital Media Network Company vakuuttaa tten ett Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart TOSHIBA Corp. Digital Media Network Company dat het toestel Radio LAN device in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze TOSHIBA Corp. Digital Media Network Company dat deze Radio LAN device voldoet aan de essentile eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. Par la prsente TOSHIBA Corp. Digital Media Network Company dclare que l'appareil Radio LAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/ CE. Par la prsente, TOSHIBA Corp. Digital Media Network Company dclare que ce Radio LAN device est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables. Hrmed intygar TOSHIBA Corp. Digital Media Network Company att denna Radio LAN device str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Undertegnede TOSHIBA Corp. Digital Media Network Company erklrer herved, at flgende udstyr Radio LAN device overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF Hiermit erklrt TOSHIBA Corp. Digital Media Network Company, dass sich dieser/diese/dieses Radio LAN device in bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi) Hiermit erklrt TOSHIBA Corp. Digital Media Network Company die bereinstimmung des Gertes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)
Dutch:
French:
Swedish:
Danish:
German:
Greek:
Italian:
Con la presente TOSHIBA Corp. Digital Media Network Company dichiara che questo Radio LAN device conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
11
Spanish: Por medio de la presente TOSHIBA Corp. Digital Media Network Company declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. TOSHIBA Corp. Digital Media Network Company declara que este Radio LAN device est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE.
Portuguese:
This device may not cause harmful interference. This device must accept any interference that may cause undesired operation.
TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.
12
Caution: Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device.
NOTE
The above Caution information applies to products that operate with an 802.11a device.
Taiwan
Article 14 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design. Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement. The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations. Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.
Article 17
13
2.4DSOF4
(4)
1 2 3 4
2.4: This equipment uses a frequency of 2.4 GHz. DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. The interference range of this equipment is less than 40m. This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems.
3. TOSHIBA Direct PC Monday Friday: 10:00 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916 Fax: 03-5444-9450
Device Authorization
This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan. The Name of the radio equipment: refer to the equipment label provided on the computer JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT
14
Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply:
Do not disassemble or modify the device. Do not install the embedded wireless module into other device. 5.17 GHz to 5.23 GHz for indoor use only
Approved Countries/Regions for use for the Atheros AR5BMB-43/44 Mini PCI Wireless network adapter
This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
NOTE
This device works on passive scan only. A peer-to-peer mode is not available in 802.11a and Turbo Mode.
802.11b (2.4 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA
15
Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries
Belgi/ Belgique: For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. For registration and license please contact IBPT/BIPT. Voor priv-gebruik buiten gebouw over publieke groud over afstand kleiner dan 300m geen registratie bij BIPT/IBPT nodig; voor gebruik over afstand groter dan 300m is wel registratie bij BIPT/IBPT nodig. Voor registratie of licentie kunt u contact opnemen met BIPT. Dans le cas dune utilisation prive, lextrieur dun btiment, audessus dun espace public, aucun enregistrement nest ncessaire pour une distance de moins de 300m. Pour une distance suprieure 300m un enregistrement auprs de IIBPT est requise. Pour les enregistrements et licences, veuillez contacter IIBPT. License required for outdoor installations. Check with reseller for procedure to follow. Anmeldung im Outdoor-Bereich notwendig, aber nicht genehmigungspflichtig.Bitte mit Hndler die Vorgehensweise abstimmen. Restricted frequency band: only channels 1 to 7 (2400 MHz and 2454 MHz respectively) may be used outdoors in France. Please contact A.R.T. (http://www.art-telecom.fr) for applicable procedures to follow. Bande de frquence restreinte: seuls les canaux 1- 7 (2400 et 2454 MHz respectivement) doivent tre utiliss endroits extrieur en France. Vous pouvez contacter IAutorit de Rgulation des Tlcommuniations (http://www.art-telecom.fr) pour la procdure suivre. License required for indoor use. Use with outdoor installations not allowed. Enecessaria la concessione ministeriale anche per luso interno. Verificare con i rivenditori la procedura da seguire. License required for outdoor installations. Check with reseller for procedure to follow. Licentie verplicht voor gebruik met buitenantennes. Neem contact op met verkoper voor juiste procedure.
Deutschland:
France:
Italia:
Nederland:
16
802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada USA Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA
Channels: 52, 56, 60, Channels: 100, 104, 108, 112, 64 116, 120, 124, 128, 132, 136, 140
Austria Belgium, France, Switzerland/Lichtenstein Denmark, Finland, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK Iceland, Spain
Indoor Only O O O
Indoor Only x O O
O: allowed : forbidden
To remain in conformance with European spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply. The user should use the wireless LAN utility to check the current channel of operation. If operation is occurring outside of the allowable frequencies as listed above, the user must cease operating the Wireless LAN at that location and consult he local technical support staff responsible for the wireless network. The 5 GHz Turbo mode feature is not allowed for operation in any European Community country.
17
This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands. This device will operate under the control of the Access Point in order to avoid operating on a channel occupied by any radar system in the area. The presence of nearby radar operation may result in temporary interruption of operation of this device. The Access Points radar detection feature will automatically restart operation on a channel free of radar. You may consult with the local technical support staff responsible for the wireless network to ensure the Access Point device(s) are properly configured for European Community operation.
Approved Countries/Regions for use for the Atheros AR5001X Mini PCI Wireless network adapter
This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
NOTE
This device works on passive scan only. A peer-to-peer mode is not available in 802.11a and Turbo Mode.
802.11b (2.4 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA
18
802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada USA Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA
Approved Countries/Regions for use for the Intel PRO/ Wireless LAN 2100 3B Mini PCI Adapter
This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Argentina Belgium Chile France Iceland Japan Mexico Norway Singapore Switzerland USA
Australia Brazil Denmark Germany Ireland Liechtenstein Netherlands Peru Spain UK Venezuela
Austria Canada Finland Greece Italy Luxembourg New Zealand Portugal Sweden Uruguay
19
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card
This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Australia Canada France Hong Kong Italy Luxembourg New Zealand Portugal Sweden UK
Austria Denmark Germany Iceland Japan Malaysia Norway Singapore Switzerland USA
Bluetooth Specification as defined and approved by The Bluetooth Special Interest Group. Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
20
Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth products with all PCs and/ or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for more information. When you use Bluetooth cards from TOSHIBA close to 2.4 GHz Wireless LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth cards from TOSHIBA, always change the frequency, move your PC to the area outside of the interference range of 2.4 GHz Wireless LAN devices (40 meters/ 43.74 yards or more) or stop transmitting from your PC. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/ computers/tnt/bluetooth.htm in Europe or http:// www.pcsupport.global.toshiba.com in the United States for more information. Bluetooth and Wireless LAN devices operate within the same radio frequency range and may interfere with one another. If you use Bluetooth and Wireless LAN devices simultaneously, you may occasionally experience a less than optimal network performance or even lose your network connection. If you should experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN. Please contact Toshiba PC product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for more information.
21
community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include:
Using the equipment with Bluetooth wireless technology on board of airplanes, or In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment.
Regulatory statements
This product complies with any mandatory product specification in any country/ region where the product is sold. In addition, the product complies with the following:
22
Caution: FCC Interference Statement
This device complies with part15 of the FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
Note that any changes or modifications to this equipment not expressly approved by the manufacturer may void the authorization to operate this equipment.
NOTE
Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the users authority to operate the equipment.
Taiwan
Article 14 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design.
23
Article 17 Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement. The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations. Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery.
2.4FH1
(4)
1 2
2.4: This equipment uses a frequency of 2.4 GHz. FH: This equipment uses FH-SS modulation.
24
3 4 The interference range of this equipment is less than 10m. This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems.
3. TOSHIBA Direct PC Monday Friday: 10:00 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916 Fax: 03-5444-9450
Device Authorization
This device obtains the Technical Regulation Conformity Certification, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law of Japan. The Name of the radio equipment: EYXF2CS TELECOM ENGINEERING CENTER Approval Number: 01NYDA1305 The following restrictions apply:
Do not disassemble or modify the device. Do not install the embedded wireless module into other device.
25
Location of the required label
(Sample shown below. Location of the label and manufacturing information may vary.)
This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the users guide carefully and keep it for your future reference. In case of any trouble with this model, please contact your nearest AUTHORIZED service station. To prevent direct exposure to the laser beam, do not try to open the enclosure. Use of controls or adjustments or performance of procedures other than those specified in the owners manual may result in hazardous radiation exposure.
Copyright
This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein. 2004 by Toshiba America Information Systems, Inc. All rights reserved.
26
Notice
The information contained in this manual, including but not limited to any product specifications, is subject to change without notice. TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL. IN NO EVENT SHALL TOSHIBA BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, OR EXEMPLARY DAMAGES, WHETHER BASED ON TORT, CONTRACT OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.
Trademarks
Satellite and Noteworthy are registered trademarks, FreedomWare, and SmartMedia are trademarks, of Toshiba America Information Systems, Inc. and/ or Toshiba Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. DirectX, Active Desktop, and DirectShow are registered trademarks, and Windows Media is a trademark of Microsoft Corporation. ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wireless Capability Ethernet Alliance. Dolby - Manufactured by Toshiba under license from Dolby Laboratories/ Dolby and the double-D symbol are trademarks of Dolby Laboratories. TouchPad is a trademark of Synaptics, Inc. All other brand and product names are trademarks or registered trademarks of their respective companies.
27
Computer disposal information
This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org.
Contents
Introduction ..............................................................35
This guide .............................................................. 36 Safety icons ........................................................... 36 Other icons used.............................................. 37 Other documentation ............................................. 38 Service options ...................................................... 38
28
Contents
29
Using the computer for the first time ..................... 52 Opening the display panel ................................ 52 Your computers features and specifications.... 53 Turning on the power....................................... 53 Activating the power-on password................... 54 Using the TouchPad ............................................ 55 Using TOSHIBA Touch and Launch.................. 58 Installing additional memory (optional) ................. 62 Removing a memory module........................... 66 Using an external keyboard.................................... 68 Connecting a mouse .............................................. 68 Connecting a printer .............................................. 69 Connecting a USB printer................................. 69 Connecting a parallel printer ............................ 69 Setting up a printer .......................................... 69 Connecting an optional external diskette drive....... 72 Using external display devices ............................... 73 Connecting an external monitor ....................... 73 Directing the display output when you turn on the computer ............................................. 73 Adjusting the quality of the external display..... 74 Display limitations ........................................... 74 Powering off the computer .................................... 75 Caring for your computer....................................... 76 Cleaning the computer ..................................... 76 Moving the computer....................................... 77 Using a computer lock ..................................... 77
30
Contents
Windows special keys .................................... 82 Overlay keys..................................................... 83 Starting a program................................................. 84 Starting a program from the Start menu.......... 85 Starting a program from Windows Explorer... 85 Starting a program from the Run dialog box ... 86 Saving your work ................................................... 88 Printing your work ................................................. 90 Backing up your files ............................................. 91 Restoring your work ........................................ 91 Using the DVD-ROM or multi-function drive.......... 92 DVD-ROM or multi-function drive components ............................................... 93 CD/DVD control buttons .................................. 93 Inserting a disc ................................................ 94 Playing an audio CD......................................... 96 Playing CDs using Auto-Run............................ 98 Creating a CD ................................................... 99 Viewing the contents of a CD or DVD............... 99 Removing a disc with the computer on.......... 100 Removing a disc with the computer off ......... 100 Caring for CD and DVD discs ......................... 101 Powering down the computer .............................. 101 Turn Off or Shut down command................... 102 Restart command .......................................... 103 Hibernation command ................................... 103 Standby command......................................... 104 Using Turn Off or Shut down ............................... 105 Turning off or shutting down more quickly .... 106 Starting again after Turn Off or Shut down .... 108 Using Hibernation ................................................ 108 Enabling the Hibernation command ............... 108 Going into Hibernation mode ......................... 108 Going into Hibernation mode more quickly.... 110
Contents
31
Starting again from Hibernation mode ........... 112 Using Standby ..................................................... 112 Going into Standby mode more quickly ......... 113 Starting again from Standby .......................... 115 Toshibas online resources................................... 115
32
Contents
Connecting the modem to a telephone line .... 138 Connecting your computer to a network ....... 138 An overview of using the Internet ........................ 140 The Internet ................................................... 140 The World Wide Web .................................... 141 Internet Service Providers.............................. 141 Connecting to the Internet ............................ 141 Surfing the Internet........................................ 142 Internet features............................................. 143 Uploading and downloading files from the Internet ................................................... 143 Exploring video features ...................................... 144 Changing the display properties setting ......... 144 Playing DVDs ................................................. 145 Display settings hot key ................................ 145 Exploring audio features ...................................... 145 Recording sounds.......................................... 146 Using a microphone....................................... 146 Adjusting recording settings .......................... 147 Using external speakers or headphones......... 147 Using PC Cards.................................................... 148 Inserting PC Cards ......................................... 148 Removing PC Cards ....................................... 149 Hot swapping................................................. 150
Contents
33
Hotkey utility ........................................................ 157 TOSHIBA Console ................................................ 157 Customize Your Computer ............................. 159 Security.......................................................... 159 Power Management ....................................... 159 Toshiba Hardware Setup ................................ 161 TOSHIBA Zooming Utility..................................... 163 Application Launch Button ................................... 164
34
Contents
Contacting Toshiba ........................................ 194 Other Toshiba Internet Web sites ........................ 195 Toshibas worldwide offices ................................. 195
Appendix B: Power Cable Connectors..................... 204 Appendix C: Using ConfigFree with your Toshiba Computer ............................... 205
Getting Started..................................................... 206 Starting ConfigFree ........................................ 206 ConfigFree Utilities............................................... 207 Connectivity Doctor ....................................... 207 Search for Wireless Devices .......................... 210 Profile Settings .............................................. 212 Quick Connect................................................ 214 Using the Automatic Switch................................. 217 Semi-Automatic Switch Feature ........................... 218
Introduction
Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go. Your system comes the Microsoft Windows XP Home or XP Pro operating system. Your operating system offers exciting features and easy Internet access. This guide contains information about your operating system and how it functions with your Toshiba computer. For specific information on the software, see the Microsoft booklet that shipped with your computer.
35
36
NOTE
The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba's Web site at pcsupport.toshiba.com. While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/ component/options availability are all subject to change without notice. For the most up-to-date product information about your computer, or to stay current with the various computer software or hardware options, visit Toshibas Web site at pcsupport.toshiba.com.
This guide
This guide introduces the computers features. You can:
Read the entire guide from beginning to end. Skim through and stop when a topic interests you. Use the table of contents and the index to find specific information. If you are new to computers, or have not used a notebook computer before, read through the first couple of chapters to familiarize yourself with the components of the computer and how to turn it on. After that, seek out whatever interests you most.
Safety icons
This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to
37
the seriousness of the risk, and the icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may result in property damage.
NOTE
38
DEFINITION: This icon indicates the definition of a term used in the text.
Other documentation
Your computer comes with the following documentation:
This electronic users guide. Guides for other programs that may come preinstalled on your computer or that are available for installation on your Recovery Media. For accessory information, visit Toshiba's Web site at accessories.toshiba.com. The Microsoft Windows operating system documentation which explains the features of the operating system.
Service options
Toshiba offers a full line of optional service programs to complement its limited warranty. To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see If Something Goes Wrong on page 165.
Chapter 1
Getting Started
This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer.
39
40
Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. Extreme heat, cold, or humidity. Liquids and corrosive chemicals. If you spill liquid into the computer, turn off the computer, unplug it from the AC power source, and let it dry out completely before turning it on again. If the computer does not operate correctly after you turn it back on, contact your network administrator. If your computer still does not operate, refer to If you need further assistance on page 193 for additional technical assistance.
This section provides hints on avoiding strain and stress injuries. For more information, consult books on ergonomics, repetitive-strain injury, and repetitive-stress syndrome.
41
Place the computer on a flat surface at a comfortable height and distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching. If you are using an external monitor, the top of the display should be no higher than eye level. If you use a paper holder, set it at about the same height and distance as the screen.
Approximately 90 angles
Footrest
42
Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. Position your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed and your forearms parallel to the floor. Your knees should be slightly higher than your hips. If necessary, use a footrest to raise the level of your knees and ease the pressure on the back of your thighs. Adjust the back of your chair so that it supports the lower curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back-support cushions are available at many office supply stores. Sit with your back straight so that your knees, hips, and elbows form approximately 90-degree angles when you work. Do not slump forward or lean back too far.
Lighting
Proper lighting can improve the visibility of the display and reduce eyestrain.
Position the display panel or external monitor so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows or shades to reduce glare. Avoid placing your computer in front of a bright light that could shine directly in your eyes. If possible, use soft, indirect lighting in your computer work area.
43
Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes.
Avoid bending, arching, or twisting your wrists. Keep them in a relaxed, neutral position while typing. Exercise your hands, wrists, and arms to improve circulation.
Work habits
The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency.
Take frequent breaks to change position, stretch your muscles, and relieve your eyes. A break of two or three minutes every half hour is more effective than a long break after several hours. Avoid performing repetitive activities for long periods. Intersperse such activities with other tasks. Focusing your eyes on your computer screen for long periods can cause eyestrain. Look away from the computer frequently and focus your eyes on a distant object for at least 30 seconds. Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes.
44
Other precautions
Your notebook computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer.
Avoid prolonged physical contact with the underside of the computer. If the computer is used for long periods, its case can become very warm. While the temperature may not feel too hot to the touch, if you maintain physical contact with the computer for a long time (if you rest the computer on your lap, for example), your skin might suffer low-heat injury. Do not apply heavy pressure to the computer or subject it to sharp impacts. Excessive pressure or impact can damage computer components or otherwise cause your computer to malfunction.
Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is used extensively. Overheating of a PC Card can result in errors or instability in the PC Card operation. Be careful when you remove a PC Card that has been used for lengthy periods of time.
Avoid spilling liquids into the computers keyboard. If you do spill a liquid that gets into the keyboard, turn off the computer immediately. Leave the computer turned off overnight to let it dry out before you use it again.
Never turn off the computer if a drive light indicates a drive is active.
45
Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both.
Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers. Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files.
Scan all new files for viruses. This precaution is especially important for files you receive via diskette, CD-ROM or DVD discs, email, or download from the Internet. Occasionally, even new programs you buy from a supplier may contain a computer virus. Youll need a special program to check for viruses. Ask your dealer or network administrator to help you.
NOTE
46
Your computer contains a rechargeable high-capacity battery that needs to be charged before you can use it. To use external power or to charge the battery, you must attach the AC adapter. See Connecting to a power source on page 48.
The names of windows displayed and the order in which windows appear may vary depending on your software setup choices.
The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software. 1 2 3 From the welcome screen, click Next to enter the Setup Wizard. Confirm acceptance of Microsofts End User License Agreement and click Next. Follow the on-screen instructions to enter the information about your computer.
47
NOTE
To register online, your computer must be connected to the Internet via a voice-grade telephone line or a Local-AreaNetwork (LAN).
NOTE
If you chose not to register now, you may register with Toshiba by clicking the Register with Toshiba icon on the desktop.
A window displays the message, Thank you. 4 Click Finish to continue. Your computer restarts automatically.
Before adding external devices, Toshiba recommends setting up your software first. See Setting up your software on page 46.
Before starting to use your computer, you may also want to:
Add more memory (see Installing additional memory (optional) on page 62)
48
Connect a mouse (see Connecting a mouse on page 68) Connect a local printer (see Connecting a printer on page 69) Install PC Cards (see Using PC Cards on page 148) Connect an external keyboard (see Using an external keyboard on page 68) Connect another display device (see Using external display devices on page 73) Connect a diskette drive (see Connecting an optional external diskette drive on page 72)
Sample power cable and sample AC adapter Hold the power cable by its plug when you connect/disconnect it. Do NOT pull the cable itself. Doing so may damage the power cable and result in a short circuit or electric shock.
49
When you connect the AC adapter to the computer, always follow the steps in the exact order as described in the User's Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adapter DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.
Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter.
To connect AC power to the computer: 1 Connect the power cable to the AC adapter.
Sample connecting the power cable to the sample AC adapter Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
50
2
Sample connecting the AC adapter to the computer 3 Connect the power cable to a live electrical outlet. The AC power indicator glows when the computer is connected to an external power source. The battery light:
Glows amber while the battery is being charged. Glows green when the battery is fully charged. Is unlit when the computer is not connected to an external power source. For information on determining battery power, see Monitoring battery power on page 121. Damaged power cables can cause fire or electric shock. Never modify, forcibly bend, place heavy objects on top of, or apply heat to the power cable. If the power cable becomes damaged or the plug overheats, discontinue use. There is a risk of electric shock. Never remove the power plug from the outlet with wet hands. Doing so may cause an electric shock.
51
TECHNICAL NOTE: When your computer is using all of the power provided by the AC Adaptor to run applications, features, and devices, the recharging of the battery can not occur. Your computer's Power Saver utility can be used to select a power level setting that reduces the power required for system operation and will allow the battery to recharge. For more information, see Power Management on page 159.
NOTE
Battery life and charge time may vary depending on the applications, power management settings, and features used.
52
Sample opening the display panel To avoid damaging the display panel, do not force it beyond the point where it moves easily. Never lift or move the computer using the display panel.
Small bright dots may appear on your TFT display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
53
NOTE
Over a period of time, and depending on the usage of the computer, the brightness of the LCD Screen will deteriorate. This is an intrinsic characteristic of LCD technology. Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Sample system icons This information applies to all the features and icons described in this guide.
54
When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.
The preinstalled operating system loads automatically. The hard disk drive indicator flashes to indicate that the hard disk drive is currently in use. Never turn off the computer while any drive is in use.
55
The TOSHIBA Console window appears. For more information see TOSHIBA Console on page 157. 2 3 4 Click Security. Click User password. Follow the on-screen instructions. The password requirement becomes active the next time you turn on your computer. When the feature is active, you must enter the password during the power-on process. After typing your password, press the Enter key. If the password is correct, the power-on process continues. If the password is incorrect, you will be prompted to try again.
NOTE
If you forget your power-on password and therefore cannot turn on your computer, take your computer to a Toshiba authorized service center for help.
After the third incorrect password submission, the system automatically shuts down.
To move the cursor to the top of the page, push your finger forward on the TouchPad. To move the cursor to the bottom of the page, drag your finger toward yourself.
56
To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. To move it to the left side, slide your finger from right to left. Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction.
NOTE
Once you have positioned your cursor, you can either click it into place by double-tapping the TouchPad or clicking the control buttons. You can disable or enable the TouchPad. See Disabling or enabling the TouchPad on page 56.
Control buttons
The control buttons are below the TouchPad and are used like the buttons on a mouse. The primary control button is the button on the left and corresponds to the left mouse button. To double-click, press the primary button twice in rapid succession. The secondary control button is the button on the right and corresponds to the right mouse button. Check your programs documentation to find whether it uses the secondary mouse button.
57
3 4
Click the Mouse icon. Click the TouchPAD ON/OFF tab. The TouchPAD ON/OFF tab view window appears.
Sample Mouse Properties window 5 6 7 8 9 Select Disable or Enable, whichever is appropriate. Click Apply. Click OK. The Mouse Properties window closes. Close the Printers and Other Hardware window. Close the Control Panel window.
You can also use a hot key (Fn + F9) to disable or enable the TouchPad. See Disabling or enabling the TouchPad on page 203.
58
Open a document Launch a program Show a list of windows and switch the active window Open Internet Explorer favorites
TOSHIBA Touch and Launch is like a miniature Windows desktop. You can personalize TOSHIBA Touch and Launch to help you work more efficiently. To activate TOSHIBA Touch and Launch, touch and hold your finger on a corner of the TouchPad. The TOSHIBA Touch and Launch window will appear.
Sample TOSHIBA Touch and Launch window A blue circle within the TOSHIBA Touch and Launch window represents your finger location on the TouchPad. As you move the blue circle over an icon in the TOSHIBA Touch and Launch window, the icon is highlighted or selected. Release your finger from a selected icon to choose the icon's function. If the icon is highlighted in orange and selected, the function corresponding to the selected icon launches and the TOSHIBA Touch and Launch window closes. If the icon is
59
highlighted in blue and selected, the function corresponding to the selected icon launches and the TOSHIBA Touch and Launch window remains open. To close the TOSHIBA Touch and Launch window, release your finger when the blue circle is not on any icon. Or, highlight the Close icon in the upper right of the TOSHIBA Touch and Launch window. The TOSHIBA Touch and Launch window has the following parts:
Corner icons Back button Title Close button
Main window
Sample parts of the TOSHIBA Touch and Launch window A short description of the currently selected corner icon appears below the TOSHIBA Touch and Launch window. The title and functions can change when you select one of the corner icons. The type and number of icons you see in the main part of the TOSHIBA Touch and Launch window is determined by which of the corner icons you select.
60
TOSHIBA Touch and Launch is controlled/adjusted via an icon on the system tray. The icon changes color when the TOSHIBA Touch and Launch is active. Double-click the icon to open the TOSHIBA Touch and Launch Settings window. Right-click the icon to see the following shortcut menu:
Settings The Settings function allows you to define the functions/ features you can access in TOSHIBA Touch and Launch
61
In the Corner Assignment section you can change the icons you see at the four corners of the TOSHIBA Touch and Launch window using the drop-down list boxes. The icons are referred to as tables in the TOSHIBA Touch and Launch Settings dialog. The Touch Pad settings button allows you to define how sensitive the TouchPad will be to your finger on the TouchPad before it actives the TOSHIBA Touch and Launch window. The Window settings button allows you to control the size and transparency of the TOSHIBA Touch and Launch window. The Option button allows you to define how folders will open, define visual affects and control when to show help. A list of tables appears in the Table section of the TOSHIBA Touch and Launch Settings window. These are the same items (icons) you can choose in the Corner Assignment section of the TOSHIBA Touch and Launch Settings. As you select a table, the Settings button may become active. Not all tables have settings. The New Table button allows you to create a new table. The Delete button deletes the selected table.
62
Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Stand by or Hibernation mode, data will be lost.
Your computer comes with enough memory to run most of todays popular applications. You may want to increase the computers memory if you use complex software or process large amounts of data. Additional memory comes in various capacities (visit the Toshiba Web site at accessories.toshiba.com for more information). Your system has one memory slot available for user upgrades. If you use the computer for a long time, the memory module will become hot. If this happens, let the module cool to room temperature before you replace it.
63
Do not try to install a memory module under the following conditions. You can damage the computer and the module. 1. The computer is turned on. 2. The computer was shut down using Standby or Hibernation mode. 3. Power to the DVD-ROM or multi-function drive has been turned on.
Do not install or remove a memory module while the DVD-ROM or multi-function drive power is on.
You need a standard Phillips no. 0 (zero) screwdriver to install a memory module. To avoid damaging the computers screws, use a standard Phillips no. 0 (zero) screwdriver that is in good condition.
If you are adding memory after you have started to use the computer, begin at step 1, otherwise skip to step 2. 1 Turn off the computer via the Start menu. See Turn Off or Shut down command on page 102. The operating system turns off the computer. 2 Close the display panel and turn the computer upside down with the front side of the computer facing you.
64
Sample using a Phillips-head screwdriver to remove the memory cover 3 4 Remove the screw that holds the memory cover in place, and remove the memory cover. Remove the new memory module from its antistatic packaging. Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its pin connector (on the side you insert into the computer).
Insert the memory module in the slot. Align the module and gently press the module down into place.
65
Sample inserting the memory module Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems.
The clips on either side of the module will click to secure the module. 6 7 8 Replace the memory cover and screw. Turn the computer over. Turn on the computer. To verify that the computer correctly recognizes the memory, see Checking total memory on page 68. 9 If the computer does not recognize the memory, shut down the computer, remove the memory cover, and make sure the memory module is seated properly.
66
Do not try to remove a memory module with the computer turned on. You can damage the computer and the device. Do not remove the memory module while the computer is in Standby mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of the above cases, the Standby configuration will not be saved. The following message appears when you turn on the power: Warning: Resume Failure Press Any Key To Continue If the computer hangs up when you turn it on, perform the following: Press the power button and hold it down for five seconds until the power turns off, then turn the power on again.
67
Pull the clips away from the memory module. The memory module pops partially out of the slot.
Sample removing the memory module 3 Carefully remove the module from the slot. Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its pin connector (on the side you insert into the computer).
Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems.
Complete the procedure by following steps 4 through 8 in Installing additional memory (optional) on page 62.
68
Connecting a mouse
You may want to use a mouse instead of the TouchPad, the computers built-in pointing device. To connect a USB mouse, plug the mouse cable into one of the USB ports.
69
Connecting a printer
You can connect a USB-compatible printer to your computer through the USB ports. You can connect a USB printer after you turn on the computer. Alternatively, you can connect a parallel printer to the computers parallel port.
Follow the manufacturers instructions for connecting a USB printer to your computer.
Follow the manufacturers instructions for connecting a parallel printer to your computer.
Setting up a printer
NOTE
70
If your printer has not been detected automatically when connected to the computer, you must install the printer driver for the model of printer that is connected to your computer. You install the printer driver either by following the instructions indicated in your printer guide, or by using the operating systems Add Printer Wizard. If you plan to set up a printer later, close or cancel the Add Printer Wizard.
Sample Control Panel 2 3 Click Printers and Other Hardware. Click the Printers and Faxes icon.
71
Sample Printers and Faxes window 4 Click Add a printer. The Add Printer Wizard window appears.
72
5
Follow the on-screen instructions. HINT: If you are using more than one printer, make sure the name is descriptive enough to help you tell the difference.
Holds 3.5-inch high-density (1.44 MB) diskettes for data transfer and storage. Allows you to boot your computer
Sample external USB diskette drive To connect an external USB diskette drive, connect the drives cable to one of the computers USB ports.
Eject button
73
Built-in display panel only Built-in display panel and external device simultaneously
74
External device only Built-in display and TV (or other external video device) simultaneously TV (or other external video device) only
Release the Fn key for the selection to take effect. TECHNICAL NOTE: You can also change these settings using the Display Properties box in the Control Panel.
Display limitations
Keep in mind that the quality of the display will be limited to the capabilities of the external video device.
If the external video device, such as an SVGA monitor, is capable of displaying at a maximum resolution of 640 x 480 and your system is set for a higher resolution, only part of the desktop will appear on the screen. You can view the lost area by scrolling to it. If you use the display hot key (Fn + F5) to change the display output with the LCD Display Stretch option
75
enabled and the Display area (resolution) set to 640 x 480 or 800 x 600, the image on the internal display panel may appear stretched.
NOTE
The Windows XP operating system by default does not display resolutions below 800 x 600. To display the 640 x 480 resolution, you may need to click the Settings tab in the Display Properties window, click Advanced, click the Adapter tab, click List all modes, and select 640 x 480.
Use the Turn Off command if you are using the Windows XP Home version operating system, or the Windows XP Professional operating system when not connected to a domain server. Use the Shut down command if you are using the Windows XP Professional operating system and connected to a domain server. If you have work in progress and are not connected to a network, use the Windows Standby or Hibernate commands to save your system settings to memory so that, when you turn on the computer again, you will automatically return to where you left off.
76
To leave the computer off for a longer period, you can use the Windows Turn Off command when not connected to a domain server or the Shut down command when connected to a domain server instead. Never turn off the computer while any drive is in use. Doing so may damage the media in use and result in loss of data.
For more information, see Powering down the computer on page 101.
77
Although your notebook computer is built to withstand reasonable shock and vibration, transport it in a carrying case for long trips. You can purchase a carrying case from your Toshiba dealer or the Toshiba Web site at accessories.toshiba.com.
Sample PORT-Noteworthy computer lock cable To secure the computer: 1 Loop the cable through or around some part of a heavy object. Make sure there is no way for a potential thief to slip the cable off the object. 2 Pass the locking end through the loop.
78
3
Insert the cables locking end into the security lock slot, then rotate the key a quarter-turn and remove it.
Sample locking the computer The computer is now securely locked to deter computer theft.
Chapter 2
Computing tips
Save your work frequently. Your work temporarily stays in the computers memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working. Your computer can be configured to warn you when the battery is running low. See Setting battery alarms on page 124. HINT: Some programs have an automatic save feature which you can turn on. This feature saves your file to the hard disk at preset intervals. See your software documentation for details.
79
80
Back up your files to storage media on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.
Use Error-Checking and Disk Defragmenter regularly to conserve disk space and help your computer perform at its optimal level. Consult your Windows XP operating system documentation for more information on these and other utilities. Scan all new files for viruses. This precaution is especially important for files you receive via diskette, email, or download from the Internet. Take frequent breaks to avoid repetitive-motion injuries and eyestrain.
Do not turn off the computer if a drive indicator light indicates a drive is active. Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both.
Before turning off the computer, use the Turn off computer command or Standby command. See Powering down the computer on page 101 to learn more about Standby. The operating system records information, such as your desktop setup, during its shut down procedure. If you do not let the operating system shut down normally, details such as new icon positions may be lost.
81
Sample keyboard
Character keys
Typing with the character keys is very much like typing on a typewriter, except that:
The spacebar creates a space character instead of just passing over an area of the page. The lowercase l (el) and the number 1 are not interchangeable. The uppercase letter O and the number 0 are not interchangeable. The Caps Lock key changes only the alphabet keys to upper case the number and symbol keys are not affected. The caps lock light on the keyboard indicator panel illuminates when you press the Caps Lock key.
82
Ctrl
Alt
Sample Ctrl, Fn and Alt keys The Ctrl, Fn, and Alt keys do different things depending on the program you are using. For more information, see your program documentation.
Function keys
The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard.
Sample function keys through F12 are called function keys because they run programmed functions when you press them. Used in combination with the Fn key, function keys marked with icons run specific functions on the computer.
F1
Sample Windows special keys The keyboard provides two keys that have special functions in the operating system:
The Windows logo key opens the Start menu. The Application key has the same function as the secondary TouchPad control button (or secondary mouse button).
83
Overlay keys
& 7
Home 7
8
8
( 9
PgUp 9
) 0
U
4
I
5
O
6
P
-
J
End
K
1 2
L
PgDn 3
: ;
+
M
Ins
>
.
0
Del
? /
.
/
Esc
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Prt Sc
Sys Req
Pause
Break
! 1
@
2
#
3
$ 4
% 5
^
6
& 7
Home 7
8
8
( 9
PgUp 9
) 0
+ =
{ [ } ]
BkSp
Home
U
4
I
5
O
6
P
-
\
Enter
PgUp
Caps Lock
J
End
K
1 2
L
PgDn 3
: ;
+
"
? /
PgDn
Shift
M
Ins
< ,
0
>
.
Del
Shift
/
End
.
Ins
Ctrl
Fn
Alt
Alt
Del
Sample keyboard overlay keys The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the ten-key keypad on a desktop computers keyboard.
For lowercase letters, hold down Fn while you type the letters. For uppercase letters, hold down both Fn and Shift while you type the letters.
84
To use the cursor control overlay when the numeric overlay is on, press and hold down Shift while you use the cursor control keys. To return to the numeric overlay, release Shift. To turn off the numeric keypad overlay, hold down the Fn key and press F11 again. The numeric mode light on the keyboard indicator panel goes out.
For lowercase letters, hold down Fn while you type the letters. For uppercase letters, hold down both Fn and Shift while you type the letters.
To use the numeric keypad overlay when the cursor control overlay is on, hold down Shift while you use the numeric overlay keys. To return to the cursor control overlay, release Shift. To turn off the cursor control overlay, hold down the Fn key and press F10 again. The cursor control mode light on the keyboard indicator panel goes out.
Starting a program
The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows Explorer. If you prefer to open the program first, you have four options:
Double-click the icon for the program on your desktop Use the Start menu
85
Use Windows Explorer to locate the program file Use the Run dialog box
86
2 3 4 5
Click Accessories. Click Windows Explorer. Click My Computer to expand the window. In the left part of the window, under the C: icon, doubleclick the folder containing the program, in this case Program Files. Windows Explorer shows the contents of the Program Files folder on the right side of the window. The left side of the window shows all the folders contained within the Program Files folder.
6 7
In the left part of the window, click Windows NT. Click Accessories. Windows Explorer shows the contents of the Accessories folder on the right side of the window.
In the right part of the window, double-click WordPad. WordPad opens. To close the program, click the Close button in the upper-right corner of the programs window.
87
If you know the programs location, type the command line. For a program in the Windows folder, type just the program name. Otherwise, type the full file path. For example, to access WordPad, type: c:\Program Files\WindowsNT\Accessories\Wordpad, then click OK. If you do not know the location, click Browse.... In the Browse dialog box, enter the file name (for example, wordpad.exe) and select the drive to search. When the operating system has found the file, click Open. HINT: To run the same program again, click the arrow to the right of the text box and select the command line from the drop-down list.
88
Saving files
1 On the File menu of your Windows program, click Save. If you are working with a document that already has a file name, this is all you need to do. If you created a new document, your program displays a Save As dialog box. Use this dialog box to specify where to store the document and to give it a file name.
Sample Save As dialog box 2 Choose the drive and folder where you want your file to be stored.
89
Type a file name, then click Save. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.
The Windows XP operating system supports file names of up to 255 characters; the names can include spaces. Some applications still require MS-DOS file names.
File names
If you plan to share your files with a computer using a preWindows 95 version of the Windows operating system, the file name must be no more than eight characters long. Typically the file name also has an extension, consisting of a period and up to three additional characters. You may use all the letters and numbers on the keyboard plus these characters: _ ^ $ ~ ! # % & { } ( ) @ and . MS-DOS file names are not case-sensitive and must not contain spaces.
90
To save: A file you are updating, open the programs File menu and click Save. A new file, choose Save As from the File menu, type a name for the file, and click OK. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.
To print a file: 1 2 3 If your printer is not on, turn it on now. In the File menu of your program, click Print. The program displays a Print dialog box. Click OK to print.
91
5 6
Right-click, select File, then click Send To. Click the icon for the destination device.
92
TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the hard disk. Make sure the backup version is the one you want before overwriting the existing file.
NOTE
For optimum DVD performance, it is recommended that you play DVDs while running the computer on AC power.
You use CD-ROMs to load and run software, and to access reference material such as catalogs, as well as listen to music.
93
Sample DVD-ROM or multi-function drive Never press the eject button or turn off the computer while the drive-in-use indicator light is glowing. Doing so could damage the disc or the drive.
The eject button requires power to operate. The manual eject button does not require power. Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Instead, use a slim object such as a straightened paper clip.
Previous track
Next track
Play/pause
Stop/eject
94
The previous track button returns to the preceding track on the disc. The next track button skips to the following track on the disc. The play/pause button starts playing the disc or makes it pause if currently playing. The stop/eject button stops a disc that is currently playing. Do not install or remove a memory module while the DVDROM or multi-function drive power is on.
Inserting a disc
Before playing an audio CD, turn the volume down. Playing the compact disc at maximum volume could damage your ears. To turn the volume down, access the Volume Control program (click Start, All Programs, Accessories, Entertainment, Volume Control), or use the volume control dial.
If the computer is turned on, press the eject button on the DVD-ROM or multi-function drive. The disc tray partially opens. To avoid damaging a disc or losing data, check that the disc activity light is off before opening the disc tray.
95
Hold the disc by its edges and check that it is clean and free of dust. Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could lose data.
Carefully place the disc in the empty tray with its label facing up.
Sample inserting a disc Be careful not to touch the drives lens (located underneath the drives spindle) or the area around it. Doing so could cause the drive to malfunction.
Gently press the center of the disc onto the spindle until it locks into place.
96
Sample positioning the disc on the spindle Make sure the disc is properly positioned on the spindle. If you position the disc incorrectly, it can jam the disc tray.
Close the disc tray by pressing gently on the center of the tray until it clicks indicating that it is locked.
Playing an audio CD
Insert an audio CD and close the disc tray. The computer automatically detects a disc in the drive and opens the Audio CD window. To play an audio CD select the Play Audio CD using Windows Media Player option and click OK.
97
98
Sample Windows Media Player window The Windows Media Player control panel works much like an ordinary compact disc player:
To play the CD or to pause, click the Play/Pause button on the CD Player control panel. To stop the CD, click the Stop button.
99
1 2
Open the Start menu and select My Computer. Click the DVD-ROM/multi-function drive icon. The disk drive will run the CD.
If your disk does not run using this method, try using an application that is associated with the media on the disk. For example, if it is a music CD, open Windows Media Player and point it to play the CD. For other types of media, use the associated software to open the files on the disk.
Creating a CD
Your computer may come with a multi-function drive that allows you to:
Play pre-recorded DVDs Play pre-recorded CDs Read and write data (depending on your system configuration) and music files to CD-Recordable (CD-R) and CD-Rewritable (CD-RW) discs; and read DVD-R/RW or DVD RAM discs. Copy protection technology included in certain media may prevent or limit recording or viewing of the media.
NOTE
For details on how to use the software, please refer to the respective Online Help menus.
100
Locate and press the eject button. The disc tray partially opens. Grasp the sides of the disc tray and pull it fully open. Remove the disc from the disc tray and place it in its protective cover. If the disc is spinning when you open the disc tray, wait for the disc to stop before removing it.
2 3
Close the disc tray by pressing gently on the center of the tray until it clicks, indicating that it is locked.
2 3
Pull the tray fully open, remove the disc and place it in its protective cover. Close the disc tray by pressing gently on the center of the tray until it clicks, indicating that it is locked.
101
Store your discs in their original containers to protect them from scratches and keep them clean. Never bend a disc or place heavy objects on top of it. Hold a disc by its outside edge. Fingerprints on the surface of a compact disc can prevent the drive from reading the data properly. Avoid exposing discs to direct sunlight or extreme heat or cold. To clean a disc, wipe it from the center outwards (not in a circle) with a clean, dry cloth. If necessary, moisten the cloth with water or a neutral cleaner (not benzine or rubbing alcohol). Let the disc dry completely before inserting it in the drive.
Pushing the power button before shutting down the Windows operating system could cause you to lose your work. Make sure the system indicator panels disk light and the drive-inuse light are off. If you turn off the power while a disk is being accessed, you may lose data or damage the disk and/or drive.
When you power down the computer, you have a number of options to choose from:
Turn Off or Shut down, which power off the computer Hibernation, which saves the current operating state to the hard disk and powers off the computer Standby, which saves the current operating state to memory and enters a low power mode Restart, which restarts the computer
102
Each option has its advantages. TECHNICAL NOTES: Before using any of these options to power down your computer, save your files and make sure the disk activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again.
No power is used while the computer is turned off. This is the most efficient mode if you will be away from your computer for an extended time. Restarting from Turn Off or Shut down uses the most time and battery power. When starting up again, the system does not automatically open the programs and files you were previously using.
103
Restart command
Restart is the same as Turn Off or Shut down but automatically powers up the computer. Use it when you need to reload the operating system, for example to activate changes to system settings.
Hibernation command
The Hibernation command shuts the computer down completely, but it first saves the current state of the computer to the hard disk. Since Hibernation mode does not require power to maintain the saved information, the system settings are retained indefinitely. Restoring information from the hard disk takes longer than restoring it from memory. When you start up again, the computer runs a self-test, loads the operating system, and then returns to the state in which you left it. Factors when choosing Hibernation mode:
While in Hibernation mode, the computer uses no battery power. Because the state of the system is held on the hard disk, no data is lost if the battery discharges. Restarting from Hibernation mode uses less time and battery power than restarting from Turn Off. Restarting from Hibernation mode uses a little more time and battery power than restarting from Standby because information is being retrieved from the hard disk instead of memory. When starting up again, the computer returns to the state in which you left it, including all open programs and files you were using.
For more information about the Hibernation command, see Using Hibernation on page 108. For information about going into Hibernation mode more quickly, see Going into Hibernation mode more quickly on page 110.
104
Standby command
Standby puts the computer into a power-saving mode. Standby holds the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off. Factors when choosing Standby:
While in Standby mode, the computer uses some battery power. The battery will eventually discharge in Standby mode. If the battery discharges, your data will be lost if you do not save your work before entering Standby mode. Restarting from Standby mode uses less time and battery power than restarting from Turn Off or Hibernation mode. When starting up again, the computer returns to the mode in which you left it, including all open programs and files you were using. If you power down using Standby and the battery discharges fully, your information will be lost. Be sure to save your work first.
For more information about the Standby, see Using Standby on page 112. For information about going into Standby mode more quickly, see Going into Standby mode more quickly on page 113.
105
The computer turns itself off. If you are using the Windows XP Professional operating system and are a member of a domain, power off the computer as follows: 1 Click the Start button, then Shut down. The Shut Down window appears.
106
Sample Shut down computer window 2 3 Select Shut down from the drop-down list. Click OK.
Holding the Shift key while the Turn Off computer Windows dialog box is open, changes the Standby button to hibernate. For more information about setting up hibernation Hibernation command on page 103 and Using Hibernation on page 108.
107
Sample TOSHIBA Power Saver Properties window 4 Select Shut down for the options you want.
When I press the power button Set this option to Shut down to have the computer shut down when you press the power button.
When I close the lid Set this option to Shut down to have the computer shut down when you close the display panel.
5 6
NOTE
Click Apply. Click OK. For more information about the Power Saver utility, see Power Management on page 159.
108
Using Hibernation
When Hibernation is enabled, you can put the computer into Hibernation in more than one way.
For more information about the Power Saver utility, see Power Management on page 159.
109
Sample Turn off computer window with shift key held down to show Hibernate option 2 Hold down the Shift key and click Hibernate (Hibernate only appears when the Shift key is pressed).
The computer saves the state of the system, including all open programs and files, to the hard disk. Then the computer turns itself off. If you are using the Windows XP Professional operating system and are a member of a domain, power off the computer using Hibernation as follows: 1 Click Start, Shut Down. The Shut Down window appears.
Sample Hibernate computer window 2 3 Select Hibernate from the drop-down list of options. Click OK.
110
The computer saves the state of the system, including all open programs and files, to the hard disk. Then the computer turns itself off.
By pressing the hotkey combination Fn + F4. See Hibernation mode on page 201. By pressing the power button By closing the display panel
To put the computer into Hibernation mode by pressing the power button or closing the display panel, you must preset the mode. 1 2 3 Open the Start menu, click Control Panel, then Performance and Maintenance. Click the Toshiba Power Saver icon. Click the Setup Action tab. The TOSHIBA Power Saver Properties window appears.
111
Sample TOSHIBA Power Saver Properties window 4 Select Hibernation for the options you want.
When I press the power button Set this option to Hibernate so that the computer will go into Hibernation mode when you press the power button.
When I close the lid Set this option to Hibernate so that the computer will go into Hibernation mode when you close the display panel.
5 6
Click Apply. Click OK. The computer is now set to automatically go into Hibernation when your option settings occur.
NOTE
For more information about the Power Saver utility, see Power Management on page 159.
112
If your computer is running on batteries, you cannot start it again by opening the display panel. To turn the system back on, press the power button.
Using Standby
If you are using the Windows XP Home operating system, or are using the Windows XP Professional operating system and are not a member of a domain, power off the computer using the Standby command as follows: 1 Click Start, Turn off computer. The Turn off computer window appears.
The computer saves the state of all open programs and files to memory, turns off the display, and goes into a low-power
113
mode. The on/off light ( ) blinks amber indicating the machine is in Standby mode. If you are using the Windows XP Professional operating system and are a member of a domain, power off the computer using the Standby command as follows: 1 Click Start, then Shut down. The Shut Down window appears.
Sample Stand by window 2 3 Select Stand by from the drop-down list of options. Click OK.
The computer saves the state of all open programs and files to memory, turns off the display, and goes into a low-power mode. The on/off light blinks amber to indicate the machine is in Standby mode. If you power down using the Standby command and the battery discharges fully, your information will be lost. Be sure to save your work often.
114
See Standby mode on page 200. By pressing the power button By closing the display panel
To put the computer into Standby mode when you press the power button or close the display panel, you must preset the mode: 1 2 3 Open the Start menu, click Control Panel then Performance and Maintenance. Click the Toshiba Power Saver icon. Click the Setup Action tab. The TOSHIBA Power Saver Properties window appears.
Sample TOSHIBA Power Saver Properties window 4 Select Standby for the options you want.
When I press the power button Set this option to Standby to put the computer into Standby mode when you press the power button.
115
Set this option to Standby to put the computer into Standby mode when you close the display panel. 5 6
NOTE
Click Apply. Click OK. For more information about the Power Saver utility, see Power Management on page 159.
Chapter 3
Mobile Computing
This chapter covers all aspects of using your computer while traveling.
116
117
Battery Notice
Battery life may vary depending on applications, power management settings. and features utilized. Recharge time varies depending on usage. The battery does not charge while the computer is using all of its power to run applications and devices. After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is normal for all batteries. To purchase a new battery pack, see your accessories information that shipped with your computer, or to stay current on the most recent software and hardware options for your computer, and for other product information, regularly check the Toshiba Web site at accessories.toshiba.com. To ensure that the battery maintains its maximum capacity, operate the computer on battery power at least once a month until the battery is fully discharged. Please see Maximizing battery life on page 129 for procedures. If the computer is continuously operated on AC power, either through an AC adapter or a docking station for an extended period, more than a month, the battery may fail to retain a charge. It may not function efficiently over the expected life of the battery and the battery light may not indicate a low-battery condition.
NOTE
For optimum DVD performance, Toshiba recommends that you play DVDs while running on AC power rather than on battery power.
Power management
Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes.
118
Changes to these settings may result in system performance or stability issues. Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact the Toshiba Global Support Centre.
Over a period of time, and depending on the usage of the computer, the brightness of the LCD Screen will deteriorate. This is an intrinsic characteristic of LCD technology. Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Battery charge time may vary depending on the applications, power management settings, and features used.
The battery needs to be charged before you can use it to power the computer.
119
Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Use only battery chargers designed to work with your notebook computer. You can order a Toshiba battery charger from Toshibas Web site at accessories.toshiba.com.
The battery is extremely hot or cold. To ensure that the battery charges to its full capacity, wait until it reaches room temperature (50 to 80 degrees Fahrenheit, 10 to 26 degrees Celsius).
120
Leave the power connected, and the battery should begin charging after a few minutes. HINT: Once the battery is fully charged, we recommend that you operate your computer on battery power until the battery discharges completely. Doing this extends battery life and helps ensure accurate monitoring of battery capacity. For more information, see Maximizing battery life on page 129.
To recharge the RTC battery, connect the computer and leave it powered on for 24 hours.
NOTE
The above error message may vary by computer model. The RTC battery does not charge while the computer is turned off even when the AC adapter is charging the computer.
If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date, or stop working.
121
NOTE
It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working. When Hibernation mode is enabled and the RTC battery is completely discharged, a warning prompts you to reset the real-time clock.
The computer can be used while the RTC battery is being charged, although the charging status of the RTC battery cannot be monitored.
Glows green when the battery is fully charged Glows amber while the battery is being charged Does not glow if the external power source is disconnected or if the battery is completely discharged
Wait at least 16 seconds after turning on the computer before trying to monitor the remaining battery power. The computer needs this time to check the batterys remaining capacity and perform its calculations.
You can monitor the batterys remaining charge. The computer calculates the remaining battery charge as it operates, based on your current rate of power use. To show remaining power:
122
1 2
Open the Start menu, click Control Panel then Performance and Maintenance. Click the Toshiba Power Saver icon. The Toshiba Power Saver Properties window appears.
Sample Toshiba Power Saver Properties window The remaining battery charge is indicated on the top left side of the dialog box. With repeated discharges and recharges, the batterys capacity will gradually decrease. A frequently used older battery will not power the computer for as long as a new battery, even when both are fully charged. TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaining charge frequently if you are working in temperatures below 50 degrees Fahrenheit. The computer calculates the remaining battery charge based on your current rate of power use and other factors such as the age of the battery.
123
The Windows operating system has additional power management options that can be accessed through an icon in the Control Panel. For more information, see Power Management on page 159.
How the computer is configured. How much you use the hard disk, DVD-ROM or multifunction drive, and diskette drives, or other optional devices. Where you are working, since operating time decreases at low temperatures.
There are various ways in which you can conserve power and extend the operating time of your battery:
Enable Standby or Hibernation, which saves power when you turn off the computer and turn it back on again. Use Toshibas power-saving options.
These power-saving options control the way in which the computer is configured. By using them, you can greatly increase the length of time you can use the computer before you need to recharge the battery. Toshiba has combined these options into preset power profiles. Using one of these profiles lets you choose between maximum power savings and peak system performance. You may also set individual power-saving options to suit your own needs. See Power Management on page 159 and Power usage mode on page 199.
124
If you do not manage to do any of these things before the battery completely runs out of power, the computer automatically enters Hibernate mode and turns itself off. Hibernate mode keeps track of where you were so, when you turn on the power again, you can continue where you left off. The computer stores the information on what you were doing until the battery runs out of power. If you have Hibernate mode enabled (the default), the computer copies the details of your open programs and files to the hard disk before shutting down.
125
NOTE
If your battery discharges fully, your information will be lost. Be sure to save your work often.
3 4
126
5
If the battery lock latches are in the locked position (toward the left of the computer), slide them towards the right of the computer.
Sample releasing the battery lock 6 Slide the battery release latch to release the battery.
127
While still holding the release latch in the open position, lift the battery pack out of the computer.
Sample removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in Disposing of used batteries safely on page 130.
128
Safety precautions
If the battery pack produces an odor, overheats or changes color or shape while it is being used or charged, turn off the computers power immediately and disconnect the power cord from the power socket. Carefully remove the battery pack from the computer. Do not try to disassemble a battery pack. Do not overcharge or reverse charge a battery. Overcharging will shorten its life, and reverse charging could damage it. Avoid touching the metal terminals of the battery with another metal object. Short-circuiting the battery can cause it to overheat and may cause damage to the battery or the computer. Do not incinerate a spent battery, as this could cause it to explode and release toxic materials. If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. To replace the main battery, use an identical battery that you can purchase through to Toshiba Web site at accessories.toshiba.com. A reverse polarity condition should be avoided with all batteries. The main battery is designed so that it cannot be installed in reverse polarity. Charge the battery only in the computer or in a battery charger designated as an approved option. When you install the battery pack, you should hear a click when it is seated properly.
129
Do not expose the battery pack to fire. The battery pack could explode.
At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below: 1 2 3 Turn off the computers power. Disconnect the AC adapter and turn on the computers power. If it does not turn on, go to step 4. Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the main battery light flashes or there is some other warning to indicate a low battery, go to step 4. Connect the AC adapter to the computer and the power cord to a power outlet. The DC-IN or AC power light should glow green, and the main battery light should glow amber to indicate that the battery pack is being charged. If the DC-IN or AC powerlight indicator does not glow, power is not being supplied. Check the connections for the AC adapter and power cord. Charge the battery pack until the main battery light glows green.
If you have extra battery packs, rotate their use. If you will not be using the system for an extended period, more than one month, remove the battery pack. Disconnect the AC adapter when the battery is fully charged. Overcharging makes the battery hot and shortens life.
130
If you are not going to use the computer for more than eight hours, disconnect the AC adapter. Store spare battery packs in a cool dry place out of direct sunlight.
After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under federal, state and local laws, it may be illegal to dispose of old batteries by placing them in the trash. Please be kind to our shared environment. Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly. If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777.
131
Traveling tips
The environmental precautions listed in Selecting a place to work on page 39, also apply while traveling.
Never leave your computer on a sunny ledge or in a place where it could get wet or covered in dust. Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cables, and compact discs. Contact your authorized Toshiba representative for more information. TECHNICAL NOTE: When traveling by air, you may be required to pass your notebook through airport security equipment. The X-ray equipment will not harm your computer.
Chapter 4
132
133
Icons
Start button
Taskbar
System tray
Icons
An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon. You can create a new desktop icon for any folder, file, or program by dragging the elements icon from its location in a window to the desktop area. The icons initially displayed on your system desktop include:
134
Recycle Bin Holds files you have deleted. You may be able to retrieve these files until you empty the Recycle Bin. TECHNICAL NOTE: If you delete a file from a diskette, it does not go into the Recycle Bin. For more information on the Recycle Bin, see Windows online Help.
Internet Explorer The Microsoft browser that provides access to the Internet.
NOTE
If you place the cursor over an icon, a popup description of the file contents appears.
Your desktop may contain other icons depending on your configuration. See Windows XP online help for more specific information on each icon and how to use it.
Start button
You use the Start button to:
Start programs Access Microsoft Windows XP operating system update information Open documents Adjust system settings Find files Access Windows Help Run programs Suspend system activity and shut down the computer
135
Taskbar
Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open. You can use these buttons to quickly switch between the programs or windows. To make a program or window the currently active one, click the associated taskbar button. You can personalize the taskbar to include not only shortcut icons but also your favorite Internet URL addresses. DEFINITION: URL stands for Uniform Resource Locator, which is the address that defines the route to a file on the Web or any other Internet facility. Generically, it is known as the Web site address.
System tray
The System tray displays icons of tasks or programs that run continuously in the background. To learn more about each task, position the cursor over the icon for a few moments and a short description of the task appears. Typical tasks in the System tray are Current time, Power usage mode, Mouse properties, and speaker volume. To activate a specific task, double-click the appropriate System tray icon.
136
Access the Internet. Communicate with your offices local area network (LAN), or a larger corporate wide area network (WAN). For specific information about connecting to a LAN or WAN, consult your network administrator.
To connect to the Internet, use an online service, or communicate across telephone lines with another computer, you need:
A modem (one comes with your computer) A telephone line A browser or communications program An Internet Service Provider (ISP) or online service if you plan to use the Internet To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at accessories.toshiba.com.
NOTE
137
The following procedure is intended to support you if you need to either upgrade your modem or reset the port to the default settings. If you are having trouble connecting through the modem, you may need to determine the current COM port name and possibly change it. To find out which port your modem is connected to: 1 2 3 Open the Start menu, and click Control Panel. Click Printers and Other Hardware. Click Phone and Modem Options. The Phone and Modem Options Properties dialog box displays. 4 Click the Modems tab. Your modem should be listed next to one of the computers COM ports. 5 6 Make a note of the COM port number. To verify that the modem is set up properly, select the modem you wish to check, and then click Properties to bring up the dialog box with information specific to that modem. Click the Diagnostics tab, and then click Query Modem. Windows XP communicates with the modem and displays identifying information reported by the modem. If Windows XP cannot communicate with the modem, it displays an error message. Consult the troubleshooting sections of your modem and Windows XP documentation. 8 9 Click OK to close the properties dialog box for that specific modem. Click OK to close the Modem Properties dialog box.
138
Now you are ready to send a fax or use the modem to connect to an online service or the Internet. For more detailed information regarding your computers modem, visit Toshibas Web site at accessories.toshiba.com.
Accessing a network
To access a network:
At the office, connect an Ethernet cable to the RJ-45 jack on your computer. For specific information about connecting to the network, consult your network administrator. While you are at home or traveling, you may need a dialup connection. Ask your network administrator for the telephone number of the network.
139
The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.
Your system may come with an optional wireless LAN module. This is a technology that expands wireless communication beyond networking equipment, and can connect many different kinds of electronic devices without the need for cables. For information on how to set up a wireless connection, refer to your wireless networking device documentation or your network administrator.
140
To use your wireless communication, flip the wireless antenna on/off switch to the On position.
The Internet The World Wide Web Internet Service Providers Connecting to the Internet Surfing the Internet Internet features Uploading and downloading files from the Internet
The Internet
The Internet is an association of thousands of networks and millions of computers around the world connected by communications lines. They all work together to share information.
141
A modem and telephone line, or a LAN connection A Web browser An Internet Service Provider (ISP) account
The Microsoft Web browser Internet Explorer is automatically configured on your system so that when you first start it, it guides you through signing up for a new ISP account, or assists you in setting up your computer to work with your existing ISP.
142
1
Once you have established an ISP account, you can connect to the Internet. Connect your computers modem to a telephone line. For more information on connecting a modem, see Connecting the modem to a telephone line on page 138. Start your Web browser. Have your modem dial the ISPs telephone number, and establish a connection with the ISPs computer.
If you are using your computer at the office, then you probably connect to the Internet through your companys network. See your network administrator about connecting to the Internet.
143
Internet features
The Internet offers many types of communication tools to help you perform many tasks.
Internet email To send and receive your own email, you need a mailbox on the Web or an email address. If you have an account with an ISP, you can probably set up an email address at the same time you sign up for the service.
Internet chat rooms A chat room is a Web site that offers a place where people with similar interests and ideas communicate in real-time, one-on-one or in groups, by typing messages which are instantly viewed by others on their computer screens.
Internet news groups A news group is similar to a chat room, but instead of using a dedicated site to converse about a specialized subject with others in real-time, it uses a Web site as a clearinghouse where all the messages are placed, like a gigantic bulletin board.
Online shopping Many Web sites offer products and services for sale.
144
Sample Display Properties dialog box 2 3 Click the Settings tab. Slide the Screen area slider bar toward Less until the setting reads 800 x 600, then click Apply. The screen blinks momentarily while the settings are adjusted.
145
4 5 6
The Monitor Settings window appears and asks if you want to keep the settings. Click Yes. To change the settings back, repeat steps 2 through 5.
Playing DVDs
Your computer must be on for you to use the DVD-ROM or multi-function drive. 1 2 3 Open the DVD-ROM or multi-function drive tray. Place the DVD in the DVD-ROM or multi-function drive. When the DVD-ROM or multi-function drive control panel appears on your screen, press the Play button.
146
Recording sounds
You can make audio recordings and save them as .wav files by connecting an external microphone or other sound source to the microphone jack and using the Sound Recorder feature in the operating system. DEFINITION: A .wav (pronounced wave) file is a format for storing sound in files.
TECHNICAL NOTE: If you record MP3 files, you will only be able to play them on a device capable of playing MP3 files.
Using a microphone
1 2 Connect an external microphone to the computer. Click Start, point to All Programs, Accessories, Entertainment, then click Sound Recorder.
147
Click the Record button and speak normally into the microphone. You can only record 60 seconds at a time.
NOTE
4 5 6
When you have finished recording, click the Stop button. To hear what you just recorded, click the Play button. To save the file, select Save from the File menu.
2 3 4
148
TECHNICAL NOTE: Use amplified speakers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer.
To play back sound files through external speakers or headphones: 1 2 Locate the headphone jack. Using any necessary adapters, plug the cable from the headphones or external speakers into the headphone jack. The headphone jack requires a 16-ohm stereo mini-jack.
Using PC Cards
PC Cards expand your computers capabilities and usefulness. You can purchase additional PC Cards from your dealer. Most PC Cards conform to the PCMCIA (Personal Computer Memory Card International Association) standard. Your computer has a PC Card slot and supports Type II cards. Check the documentation that came with the PC Card to see if it conforms to the PCMCIA 2.1 standard, or later. Other cards may work with your computer, but are likely to be much more difficult to set up and use.
Inserting PC Cards
Use caution when lifting or turning your computer. Failure to do so may result in damage to components, such as cables, attached to your computer, or to the computer itself.
Before you insert a PC Card, refer to the documentation that comes with the card to see if you need to do anything before you insert it.
149
To insert a PC Card: 1 Turn off the computer. You may also hot swap a PC Card (see Hot swapping on page 150). 2 Align the card connectors with the PC Card slot and carefully slide the card into the slot until it locks into place.
Sample inserting a PC Card To avoid damaging the PC Card or the computer, do not force the card into the PC Card slot.
Removing PC Cards
1 Stop the PC Card by clicking the Safely Remove Hardware icon on the system tray. After the Safe to Remove Hardware message appears, it is safe to remove the PC Card. 2 To remove the PC Card, press the slots eject button once.
150
Hot swapping
One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called hot swapping.
Never remove a hard disk card while the system is accessing it. Never remove a network card while you are connected to a network.
Before removing a PC Card, stop it by clicking the Safely Remove Hardware icon on the System tray. Once the PC Card has stopped, you can safely remove it. See Removing PC Cards on page 149.
Chapter 5
Toshiba Utilities
Your computer includes several utilities designed to help you to configure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this chapter:
TOSHIBA Accessibility Fn-esse Hotkey utility TOSHIBA Console TOSHIBA Zooming Utility Application Launch Button
151
152
TOSHIBA Accessibility
The TOSHIBA Accessibility utility allows you to use the Fn key to create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility enables you to make the Fn key a sticky key, meaning you can press it once, release it and then press a function key to activate the hot key function. To open Accessibility: 1 2 3 Click Start, then click All Programs. Select Toshiba, Utilities, Accessibility. The TOSHIBA Accessibility window appears. Check the Use Fn-StickyKey box.
Sample TOSHIBA Accessibility window 4 5 Put a check mark next to the desired option. Click Apply, then click OK. The function is now active.
153
Fn-esse
The operating system shortcuts and Toshibas Fn-esse program provide quick ways to open programs, documents, and folders from within any program without using the Start menu. This section describes how to use the Fn-esse program to quickly access your programs and files. With Fn-esse, you can assign an Fn key combination to:
Open a Windows program Open a file in its associated Windows program Display a customized folder of Windows programs and/ or files from which to choose
The system also has several keys, known as hot keys, that perform preassigned operations. You can assign any key that is not associated with a hot key or a keyboard overlay.
Starting Fn-esse
To access Fn-esse, click Start, All Programs, Toshiba, Utilities and Fn-esse. The Fn-esse keyboard appears.
154
The keys are color-coded as follows: Available keys are white. Assigned keys and keys associated with a popup list are shown on the Fn-esse keyboard in the selected color. Unavailable keys are dark gray.
155
The program or document is now associated with the key you just selected. To open the program or document, press Fn plus the appropriate key.
To make a direct key assignment, select Direct to display the Add/Edit Command window, then complete these steps:
Enter the Description, Command Line, and Working Directory for the new Fn-esse key assignment, or click the Browse button to specify this information. Click OK.
To make a popup assignment, select Popup to display the Application Explorer window, then complete these steps:
Select the desired folder. The left side of the Application Explorer window displays the folders in the Programs menu. The right side lists the programs and documents in the folder. These are the items that appear in the popup list.
156
To create a popup list with items from various folders, or to pick only a few items from a folder, create a new folder containing only the desired programs and documents. If you are unsure how to do this, refer to your operating system documentation. Click OK to associate the folder with the key you just selected. To open a popup list showing the items in that folder, press Fn plus the appropriate key.
157
Hotkey utility
The hotkey utility allows you to receive a confirmation message when you use the hot key combination for Standby [Fn + F3] and Hibernation [Fn + F4]. To activate the utility: Click Start, All Programs, Toshiba, Utilities, Hotkey utility. The Toshiba Hotkey utility window appears.
Sample Toshiba Hotkey utility window 4 5 Put a check mark next to the desired option. Click OK.
TOSHIBA Console
The TOSHIBA Console provides quick access to computer functions and allows you to customize a range of computer settings. To access the TOSHIBA Console, do one of the following:
158
Use the Start menu. Click Start, then click All Programs. Point to TOSHIBA, then Utilities, then click the resulting Console selection. The TOSHIBA Console window appears.
Sample TOSHIBA Console window The TOSHIBA Console offers the following features:
159
Power Management (See Power Management on page 159.) Mouse (properties) Hotkey assignment (See Fn-esse on page 153.) Toshiba Hardware (See Toshiba Hardware Setup on page 161.) ConfigFree (See Using ConfigFree with your Toshiba Computer on page 205.)
Security
The features available in this category are:
Power Management
The Power Management feature enables you to control your computers power usage, regardless of the source, and use the many preset power modes, or create one yourself. To access Power Management through the TOSHIBA Console, double-click the Power Management icon. The TOSHIBA Power Saver Properties window appears.
160
Sample TOSHIBA Power Saver Properties window The TOSHIBA Power Saver Properties window shows the power profiles, which are optimized for several different working environments. You can either use one of the preset modes or create and use your own customized profile. The preset profiles cannot be deleted. By changing the options that appear in the TOSHIBA Power Saver Properties window and clicking OK, you can reconfigure that function. Any options that you change become effective when you click either OK or Apply.
Profiles
This section lists the preset profiles along with the estimated battery life for each mode. The preset profiles are:
161
Although you can change the properties for any of these profiles, this is not recommended. If you need a customized profile, create a new profile with the properties you require. The DVD Playback profile applies only when a DVD program is playing.
162
Sample TOSHIBA HWSetup window The TOSHIBA HWSetup window appears with tabs for the following:
Boot Priority Allows you to change the sequence in which your computer searches the drives for the operating system. You can also manually choose the Boot Priority by pressing the power button, then quickly pressing the F12 key, or the right or left arrow keys. Select the boot device by pressing the right or left arrow keys or the F12 key. Then press the Enter key.
NOTE
Since the system is a quick-booting system, you must press the arrow keys or the F12 key immediately after pressing the power button.
163
Keyboard Allows you to enable or disable the wakeup on keyboard feature. The feature allows you to wake the machine from Standby by pressing a key. USB Allows you to enable or disable USB Legacy Emulation. LAN Lets you enable or disable LAN features. General Shows the BIOS version, and allows you to set BIOS defaults. Password Allows you to set or reset a user password for the power-on process and for instant security. Parallel/Printer Allows you to configure the printer port type. Display Allows you to select the built-in LCD and/or external monitor when the computer powers on.
Microsoft Internet Explorer Microsoft Office Windows Media Player Adobe Reader Icons on the desktop
To configure the Toshiba Zooming Utility, double-click the Toshiba Zooming Utility on the task bar. The TOSHIBA Zooming utility screen appears.
164
Sample TOSHIBA Zooming Utility Properties screen To zoom in, hold down the Fn key and press 2; to zoom out, hold down the Fn key and press 1.
Chapter 6
165
166
1 2
To close a program that has stopped responding: Press Ctrl, Alt, and Del simultaneously (once). The Windows Task Manager window appears. Click the Applications tab. If a program has stopped responding, the words not responding appear beside its name in the list. 3 Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with step 4. 4 5 Close the remaining programs one by one by selecting the program name, then End Task. Turn off your computer according to the instructions in Turn Off or Shut down command on page 102.
167
Press Enter to add a paragraph break and type some notes describing what you were doing when you received the message. Save the file and refer to it when you contact the software manufacturer.
The computer starts but, when you press a key, nothing happens.
You are probably in Standby mode and have a software or resource conflict. When this happens, turning the power on returns you to the problem instead of restarting the system. To clear the condition, press Ctrl, Alt, and Del simultaneously, select Shutdown, then Restart to restart the computer. Clearing the condition may get the computer running, but it will not solve a resource conflict. Read the documentation that came with the conflicting device and Resolving a hardware conflict on page 171.
The computer is not accessing the hard disk or the diskette drive.
Your computer normally loads the operating system from the hard disk. If you have a hard disk problem, you will not be able to start the computer. Insert a system diskette into the
168
diskette drive, press the left or right arrow key and choose your boot-up device. HINT: Press F12 as you power on the computer to access the boot priority menu.
The operating system fails to start after the Starting Windows XP message appears. The operating system takes a long time to start.
169
The operating system responds differently from the normal routine. The screen does not look right.
Unless a hardware device has failed, problems usually occur when you change the system in some way such as installing a new program or adding a device. If you experience any of these problems, use the options in the Startup menu to fix the problem.
Safe Mode Safe Mode with Networking Safe Mode with Command Prompt Enable Boot Logging Enable VGA Mode Last known good configuration (your most recent settings that worked) Directory Services Restore Mode (Windows domain controllers only) Debugging Mode Start Windows normally
170
See your Windows documentation for further explanation. TECHNICAL NOTE: If your computer is connected to a network, the Startup menu may display different versions of Safe mode.
Internet problems
My Internet connection is very slow.
Many factors contribute to the speed with which you can surf the Internet. They include: modem speed, time of day (when everyone else is surfing, your access can be slow) and popularity of the site. If accessing a particular site is very slow, try later.
171
Click Start, then click Help and Support. The Help and Support Center window appears. Then do one or both of the following: In the search field, type in the topic of the problem with which you need help and follow the on-screen instructions. Click a problem you would like help with from the listings and follow the on-screen instructions.
You can connect to Support Online by clicking Support from the menu.
If there is still a problem, the operating system should display a message that explains what the conflict is.
A plan of action
The smooth operation of the system depends on the successful interaction of all devices, programs, and features. If the system or one of its attached devices is not working, resolving the problem can be time-consuming and frustrating.
172
The recommended procedure for getting multiple devices to work together is to add and set up one device at a time. After you add each device, test it to make sure it and all previously connected devices work. The device most recently connected to the system is the one most likely to be causing a hardware conflict.
Some of the IRQs may be shared by multiple devices. This is called IRQ sharing and is normal.
173
Resolving conflicts
There are things you can do to resolve hardware conflicts:
Disable the device. For an older device, remove it from the computer. Disable another system component and use its resources for the new device, see Fixing a problem with Device Manager on page 174. Reconfigure the device so that its requirements do not conflict. Refer to the devices documentation for instructions about changing settings on the device.
174
Disabling a device
1 2 3 4 5 Click Start, Control Panel, Performance and Maintenance, Administrative Tools. Double-click the Computer Management icon. In the left pane, click Device Manager. Select the specific device from the device category. In the toolbar, look to the far right for an icon of a monitor with a strike mark through a circle on the front. This is the disable feature. Click the icon. You are given the option of disabling the device. 7 Click yes or no, whichever is appropriate.
175
To check a devices properties: 1 2 3 4 5 Click Start, Control Panel, Performance and Maintenance, Administrative Tools. Double-click the Computer Management icon. In the left pane, click Device Manager. To view the device(s) installed, double-click the device type. To view the properties, double-click the device. The operating system displays the Device Properties window, which provides an array of tabs. They may include:
The General tab, which provides basic information about the device. The Resource tab, which lists resources assigned to the device. The Drivers tab, which displays the driver being used by the device.
A Troubleshooting button is also present. Click Troubleshooting. A Help and Support window for that device appears. For more information about Device Manager, refer to Windows XP online help.
176
An incorrectly connected or faulty memory module may cause errors that seem to be device-related. It is worthwhile checking for these first: 1 2 3 Turn off your computer according to the instructions in Turn Off or Shut down command on page 102. Remove the memory module, following the instructions in Removing a memory module on page 66. Reinstall the memory module, following the instructions in Installing additional memory (optional) on page 62, and making sure it is seated properly. Check for the error again. If the error recurs, remove the memory module entirely and check for the error again. If removing the memory module eliminates the error, the memory module may be faulty. If the error recurs without the memory module installed, the error is not caused by the memory module. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work.
4 5
177
The AC power light does not come on when you plug in the AC adapter and power cable.
Make sure the AC adapter and power cable are firmly plugged into both the wall outlet and the computer. If the AC power light still does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance.
The AC adapter and power cable work correctly, but the battery will not charge.
The battery does not charge when your computer is using all of its power to run applications, features, and devices. Try turning off the computer. The main battery may not be inserted correctly in the computer. Turn off the computer, remove the battery, clean the contacts with a soft dry cloth (if necessary) and replace the battery. The battery may be too hot or too cold to charge properly. If you think this is the probable cause, let the battery reach room temperature and try again. If the battery has completely discharged, it will not begin charging immediately. Leave the AC adapter and power cable connected, wait 20 minutes and see if the battery is charging. If the battery light is glowing after 20 minutes, let the computer continue charging the battery for at least another 20 minutes before you turn on the computer.
178
If the battery light does not glow after 20 minutes, the battery may have reached the end of its useful life. Try replacing it.
The battery appears not to power the computer for as long as it usually does.
If you frequently recharge a partially charged battery, it may not charge fully. Let the battery discharge completely, then try charging it again. Check the power options using the Power Management utility. Have you added a device, such as a PC Card or memory module, that takes its power from the battery? Is your software using the hard disk more? Is the display set to turn off automatically? Was the battery fully charged to begin with? All these conditions affect how long the charge lasts. For more information on maximizing battery power, see Charging the batteries on page 118.
Keyboard problems
If, when you type, strange things happen or nothing happens, the problem may be related to the keyboard itself.
179
You have connected an external keyboard and the operating system displays one or more keyboard error messages.
If you have a second keyboard, try it. If it works, the first keyboard may be defective or incompatible with your computer.
Display problems
Here are some typical display problems and their solutions:
Built-in display panel only Built-in display panel and external monitor simultaneously External monitor only External video device only
To open the display options window, press Fn and F5 simultaneously. To choose the desired option, hold down Fn and press F5 repeatedly until your choice is selected. To decrease or increase screen brightness you can use the hot keys Fn + F6 or Fn + F7.
180
If you are using an external monitor: Check that the monitor is turned on. Check that the monitors power cable is firmly plugged into a working power outlet. Check that the cable connecting the external monitor to the computer is firmly attached. Try adjusting the contrast and brightness controls on the external monitor. Make sure the display choice is not set for the built-in screen only.
A message tells you that there is a problem with your display settings and that the adapter type is incorrect or the current settings do not work with your hardware.
Reduce the size of the color palette to one that is supported by the computers internal display.
181
To change the display properties: 1 2 3 4 Point at the desktop and click with the secondary button. The Display Properties window appears. Click Properties, then click the Settings tab. Adjust the screen resolution and/or color quality. Click OK.
The display mode is set to Simultaneous and the external display device does not work.
Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher.
Small bright dots appear on your TFT display when you turn on your computer.
Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. The small bright dots that appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
NOTE
Over a period of time, and depending on the usage of the computer, the brightness of the LCD Screen will deteriorate. This is an intrinsic characteristic of LCD technology. Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
182
You are having trouble accessing a disk, or one or more files appear to be missing.
Make sure you are identifying the drive by its correct name (A: or C:).
Error-checking
Run Error-checking, which analyzes the directories, files and file system on the disk and repairs any damage it finds: To run Error-checking: 1 2 Click Start, then click My Computer. Right-click the drive you want to check and click Properties. The drives properties box appears. 3 4 5 Click the Tools tab. Click the Check Now button. The Check Disk window appears. You can choose one or both options:
Automatically fix file system errors Scan for and attempt recovery of bad sectors
183
184
You press the disc eject button, but the drive tray does not slide out.
Make sure the computer is connected to a power source and turned on. The DVD-ROM or multi-function drive eject mechanism requires power to operate. To remove a disc without turning on the computer, use a narrow object, such as a straightened paper clip, to press the manual eject button. This button is in the small hole next to the disc eject button on the right side of the computer. Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it.
185
186
Sample Secondary IDE Channel Properties window 7 8 Click the Advanced Settings tab. Look at Device 0. The current transfer mode should be Ultra DMA Mode 2. If it is not, select Ultra DMA Mode 2 from the pull-down menu and click OK.
187
in the Mixer Utility (default Enabled), may cause feedback. Revert to the default settings.
PC Card problems
PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, or a pager. Most PC Card problems occur during installation and setup of new cards. If youre having trouble getting one or more of these devices to work together, several sections in this chapter may apply. Resource conflicts can cause problems when using PC Cards. See Resolving a hardware conflict on page 171.
188
PC Card checklist
Make sure the card is inserted properly into the slot. See Using PC Cards on page 148 for how to insert PC Cards.
Make sure all cables are securely connected. Occasionally a defective PC Card slips through quality control. If another PCMCIA-equipped computer is available, try the card in that machine. If the card malfunctions again, it may be defective.
The slot appears to be dead. PC Cards that used to work no longer work.
Check the PC Card status: 1 2 Click Start. Click the My Computer icon with the secondary button, then click Properties. The System Properties window appears. 3 4 5 6 Click the Hardware tab. Click the Device Manager button. Double-click the appropriate category for the PC Card being used. Double-click the name of the PC Card device. The operating system displays your PC Cards Properties window, which contains information about your PC Card configuration and status.
189
Hot swapping (removing one PC Card and inserting another without turning the computer off) fails.
Follow this procedure before you remove a PC Card: 1 2 Click the Safely Remove Hardware icon on the System tray. Click Safely remove xxxx, where xxxx is the identifier for your PC Card. The operating system displays a message that you may safely remove the card. 3 Remove the card from the slot.
190
Printer problems
This section lists some of the most common printer problems:
The printer will not print what you see on the screen.
Many programs display information on the screen differently from the way they print it. See if your program has a print preview mode. This mode lets you see your work exactly as it will print. Contact the software manufacturer for more information.
191
Modem problems
This section lists common modem problems:
The modem is on, set up properly and still will not transmit or receive data.
Make sure the line has a dial tone. Connect a telephone handset to the line to check this. The other system may be busy or off line. Try making a test transmission to someone else.
192
Copy files to diskette, following the steps in Saving your work on page 88. Copy files to your network partition. Connect a tape drive to the system and use specialized software to copy everything on the hard disk to a tape.
Some people use a combination of these methods, backing up all files to tape weekly and copying critical files to diskette on a daily basis. If you have installed your own programs, you should back up these programs as well as your data files. If something goes wrong that requires you to reformat your hard disk and start again, reloading all your programs and data files from a backup source will save time.
193
Your local computer store or book store sells a variety of selfhelp books you can use to supplement the information in the guides.
Review the troubleshooting information in your operating system documentation. If the problem occurs while you are running a program, consult the programs documentation for troubleshooting suggestions. Contact the software companys technical support group for their assistance. Consult the dealer or authorized Toshiba representative from whom you purchased your computer and/or program. Your dealer is your best source for current information.
Detailed system specifications are available at www.ts.toshiba.com by selecting your particular product and model number, clicking GO, and then clicking the Detailed Specs link from the menu on the left. Or just refer to the computer documentation shipped with your product. For the number of a Toshiba dealer, see Toshiba voice contact on page 194.
194
Contacting Toshiba
If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at accessories.toshiba.com.
Your computers model and model number. Your computers serial number. The computer and any optional devices related to the problem. Backup copies of your Windows operating system and all other preloaded software on your choice of media. Name and version of the program involved in the problem along with its installation media. Information about what you were doing when the problem occurred. Exact error messages and when they occurred.
Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273
195
Worldwide Toshiba corporate site Marketing and product information in the USA Canada Europe Japan Mexico and all of Latin America
computers.toshiba.com
196
Latin America and Caribbean Toshiba America Information Systems 9740 Irvine Blvd. Irvine, California 92618 USA 800-457-7777 (within the US) 949-859-4273 (outside of the US this call may incur long-distance charges) Spain Toshiba Information Systems (Espaa) S.A. Parque Empresarial San Fernando Edificio Europa, 1a Planta Escalera A 28831 (Madrid) San Fernando de Henares Spain United States Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States
Mexico Toshiba de Mxico S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF.
United Kingdom Toshiba Information Systems (U.K) Ltd. Toshiba Court Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL United Kingdom The Rest of Europe Toshiba Europe (I.E.) GmbH Hammfelddamm 8 D-4-1460 Neuss Germany
For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm.
Appendix A
Hot Keys
Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls.
Volume Mute
Fn
This hot key enables/disables volume mute on your computer. When volume mute is enabled, no sound will come from the speakers or headphones.
Fn
Without a password
The Fn + F1 key combination turns off the display and activates instant security. Using the pointing device or any key will
197
198
make the displays content reappear, if no password is set for the current user.
With a password
The Fn + F1 key combination turns off the display and activates instant security. If you set a blank screen saver, pressing the Fn + F1 key combination to activate instant security will cause the screen to go blank. Using the pointing device or any key will make the displays content reappear. The Windows operating system log-on screen will appear, prompting you for a password. After typing in the password for the current user, press Enter. To activate the password feature: 1 2 3 Click Start, Control Panel. Click Appearances and Themes. Click one of the following:
Choose a screen saver in the Pick a task section. Display in the or pick a Control Panel icon section.
The Display Properties window appears. 4 If you clicked Choose a screen saver, the Screen Saver tab has already been selected. If it is not selected, click the Screen Saver tab. Click the On resume, password protected check box. Click OK.
5 6
199
To set up a password with a screen saver, go to Windows XP Help for instructions: 1 2 3 4 Click Start, Help and Support. In the Search field, type password screen saver. Press Enter. Click the Protect your files with a screen saver password link located under the suggested topics.
Follow the steps listed in the Windows Help to set up your password-protected screen saver. To ensure the password protection is activated after pressing (to activate instant security), wait ten seconds before walking away from the computer.
Fn + F1
This hot key displays the power usage pop-up window and cycles through the battery save modes. The power usage modes in the operating system under battery power are: Long Life, Normal, High Power, DVD Playback and Presentation
Sample power usage modes The power usage mode in the Windows operating system under AC power is Full Power only.
200
Fn +
Standby mode
This hot key puts the computer into Standby mode.
A message box is displayed by default to confirm that the computer is going into Standby mode. This message box can be set so it does not display.
For more information about Standby mode, please see Using Standby on page 112.
201
Hibernation mode
Fn +
If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it does not display.
If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see Using Hibernation on page 108.
202
Fn +
Display modes
This hot key cycles through the power-on display options. The display modes are:
Built-in display panel only Built-in display panel and external monitor simultaneously External monitor only
In order to use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device.
Display brightness
Fn
+ +
The Fn + F6 hot key decreases the screen brightness. The Fn + F7 hot key increases the screen brightness.
Fn
203
This hot key enables/disables the TouchPad. To use the TouchPad, see Disabling or enabling the TouchPad on page 56.
Fn
+ +
F11
This hot key turns the cursor control overlay on and off. This hot key turns the numeric overlay on and off. This hot key turns the scroll lock feature on and
Fn
F12
+ off.
Fn Fn
+ [Spacebar] This hot key switches screen or video modes. +1 This hot key turns the Zooming utility to zoomin. For more information, see TOSHIBA Zooming Utility on page 163. This hot key turns the Zooming utility to zoomout. For more information, see TOSHIBA Zooming Utility on page 163.
Fn
Fn
+2
Appendix B
United Kingdom
Australia
Europe
VDA approved NEMKO approved
AS approved
204
Appendix C
Connectivity DoctorThe Connectivity Doctor utility is used to analyze network connections and fix networking problems with your notebook computer. For more information, see Connectivity Doctor on page 207. Search for Wireless DevicesThe Search for Wireless Devices utility searches for wireless LAN and Bluetooth devices used in the neighborhood, and displays information about them on a virtual map. For more information, see Search for Wireless Devices on page 210. Profile SettingsThe Profiles utility lets you switch between network configurations. For more information, see Profile Settings on page 212.
205
206
Getting Started
Getting Started
This section contains information about the ConfigFree main screen, and how to start and setup ConfigFree. For more detailed information on setting up and using ConfigFree, see the Help File included in the application.
Starting ConfigFree
To start ConfigFree, be sure the computer has a wired or wireless connection. Then perform any of the following steps:
(Microsoft Windows XP or 2000) Click the Start button, and select All Programs, TOSHIBA, Networking, ConfigFree. Double-click the ConfigFree icon on the taskbar.
Press the Toshiba Console button (if applicable to your system) to open the Toshiba Console, and then click the ConfigFree icon. Click the ConfigFree icon click the desired utility. on the taskbar, and then
NOTE
If your computer is not connected to a network, the ConfigFree icon on the taskbar is displayed with an X.
When you start a search for wireless devices, ConfigFree Launcher displays on your computer desktop. You can then click the appropriate icon on the Launcher to start the desired ConfigFree utilities.
ConfigFree Utilities
207
ConfigFree Utilities
Connectivity Doctor
The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer. The Connectivity Doctor works with the following network devices:
Wired and wireless network devices Routers, hubs, and bridges Access points
208
ConfigFree Utilities
Sample Connectivity Doctor screen Moving the mouse pointer over a wired or wireless network device icon displays information about the device, such as its IP address, subnet mask, and MAC address. A wireless network device also shows information such as the network SSID and the devices Wired Equivalent Privacy (WEP) key settings.
ConfigFree Utilities
209
If a problem, or potential problem, is detected, a triangle containing an exclamation point appears in the Connectivity Doctor screen and an orange frame describes the relevant location. You can then view a possible cause and solution for the problem by clicking the exclamation point. For example, if the connection to a wireless network cannot be established because the wireless communication switch is turned off, an exclamation point appears next to the wireless communication switch. Clicking the exclamation point displays a description of the problem and a solution. The following checkboxes and buttons are provided on the Connectivity Doctor screen:
Stay on the task tray Options Log When checked, the ConfigFree icon resides in the system tray. Displays ConfigFree setting screen. Lets you create a diagnostic log, view a history of log files, or delete the history. Log files are saved as CFhtmlxxxxx.htm, where xxxxx is the creation date and time. They reside in the folder: C;\Documents and Settings\username\Local Settings\Temp Displays the version of Connectivity Doctor. Displays online help. Closes the Connectivity Doctor screen.
210
ConfigFree Utilities
A virtual map appears with a graphical representation of the wireless devices that have been detected.
NOTE
Search for Wireless Devices can also be started from the ConfigFree Launcher.
For Wi-Fi networks, the intensity of a signal is displayed in five levels or bands. The signal from the connected access point is displayed in the bands surrounding the PC icon at the center of the map. Placing the pointer over the displayed point of light shows detailed information about the wireless device.
NOTE
The wireless device shown near the center of the map is not necessarily near your notebook computer. If a wireless device located a distance away also has a strong signal, it appears near the center of the map as well.
ConfigFree Utilities
211
Sample viewing Wi-Fi devices The following screen shows an example of Bluetooth devices that are detected. As with the Wi-Fi screen, moving the mouse pointer over a device icon displays information about the device.
Sample viewing Bluetooth devices You can connect to devices shown on the Bluetooth map: 1 Click the icon of a Bluetooth device.
212
2 3
ConfigFree Utilities
Click your own computer at the center of the map. Configured devices are automatically connected. Devices not yet configured launch the Add New Connection Wizard, where you can configure and connect to the device.
Profile Settings
The Profile Settings utility lets you save network settings in profiles. ConfigFree profiles are useful for easily switching network settings and devices.You can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally, for example, you can set up a profile to match that environment and connect to the network. Similarly, users who access networks in the office and at home can set up profiles to handle these networking environments. A profile contains the currently configured network settings on the computer, as well as information about any network devices. The following settings can be saved (or captured) in a profile:
Internet settings includes LAN settings (proxy server settings) and the address of a home page that opens automatically when Internet Explorer starts. Devices lets you enable or disable settings of wired and wireless network devices, infrared devices, and set the power status of Bluetooth antennas. TCP/IP settings includes DHCP, IP address, subnet mask, default gateway, DNS server, and WINS server settings.
ConfigFree Utilities
213
Personal firewall settings for Internet connections. Dial-up connection settings for the default connection. File and printer sharing settings. Printer settings for the default printer.
Move the pointer to Profile. Click Add. The Add Profile screen appears. Select Capture and click OK. The Add Profile screen appears. Enter the name of the profile you want to create. Enter any optional comments, if desired. Click Change Icon and select an icon for this profile. Under Captured Items, select the items you want to capture for this profile. If connecting with a wireless network, select the desired Auto Switch Settings. (These options are unavailable if wireless devices have been disabled.)
10 Under Execute this program after switching, click the Browse button and select the program, file, or Web site URL that is to start after switching to this profile. For example to have Internet Explorer start in Windows XP after switching profiles, type: C:\Program Files\Internet Explorer\IEXPLORE.EXE 11 Click OK.
214
ConfigFree Utilities
The online help provides real-world examples of setting up profiles for different networking environments.
After you set up one or more profiles, you can check their settings and fine-tune them as necessary. Profiles can also be imported and exported. This feature is useful when transferring profile settings to other computers. For more information about modifying, importing, and exporting profiles, refer to the online help.
Quick Connect
The Quick Connect feature switches the Wireless LAN connection to connect to a Toshiba Wireless Projector. Once the projector utility is installed, launching the Quick Connect utility automatically opens the Wireless Data Projector Application. There you can configure how you would like to use the projector.
ConfigFree Utilities
215
To connect to a Toshiba Wireless Projector: 1 2 Click the icon in the system tray.
Move the mouse pointer to Toshiba Wireless Projector (DPJ), then click Connect.
Launching Quick Connect prevents you from using the network to connect to a Toshiba Wireless Projector when the wireless LAN Configuration is set to Ad hoc. If you are connected to an access point, the connection is broken and reestablished later. To review the current Toshiba Wireless Projector settings and change them if necessary: 1 2 Click the icon in the system tray.
Move the mouse pointer to Toshiba Wireless Projector (DPJ), then click Settings. The Quick Connect properties dialog box appears. Complete the settings. Refer to the online help if necessary. Click OK. The default connection setting is for Ad hoc mode, therefore, if the setting on the Toshiba Wireless Projector is in Infrastructure mode, it will not connect, however; you can change the settings to Infrastructure mode to match the settings on the projector.
3 4
NOTE
216
ConfigFree Utilities
Sample Projector icon when connected with Quick Connect If the wireless mode for the wireless setting is set for 5 GHz (802.11a), Quick Connect changes this mode to 2.4 GHz (802.11b) and then connects to the projector. The wireless LAN configuration returns to the settings that were last used before the Quick Connect function was started:
If the Toshiba Wireless Projector utility is closed. If you select Toshiba Wireless Projector (DPJ) from the ConfigFree tray menu (this disconnects the wireless LAN connection). If you select a profile from the ConfigFree tray menu or when you disable a wireless device. If you close ConfigFree.
217
Right-click the
Click Auto Switch. The Auto Switch dialog box appears. Check Enable Wireless when cable disconnect occurs. Click OK. If your computer is connected to multiple wireless LAN devices, the Auto Switch (SSID) feature is disabled. To enable this feature, only one wireless LAN device can be used.
218
Click Auto Switch. The Auto Switch dialog box appears. Select the Auto Switch (SSID) tab. Select the profile to be automatically selected when the SSID is detected, then click Add. The profile is moved to the List of target SSIDs and profiles. Repeat the previous step for each additional profile you want to select. Select Automatically switch profiles when connected to this SSID. Check Automatically switch profile when connected to this SSID. Click OK.
5 6 7 8
The computer is now configured to use the Semi-Automatic Switch feature. When the computer connects to an SSID in a profile, a display notification window appears. You can then click Switch on the window to switch profiles. You can also set the option for having the switch be automatic without the need for a notification.
NOTE
Several profiles can be defined for a single SSID. In this case, several notification windows are displayed. By clicking these windows, you can switch to the profile for that location.
Glossary
TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer.
Acronyms
The following acronyms may appear in this users guide.
AC BIOS bps CD CD-ROM CD-RW CMOS COM1 COM2 CPU DC alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory complementary metal-oxide semiconductor communications port 1 (serial port) communications port 2 (serial port) central processing unit direct current
219
220
Glossary
DMA DIMM DOS DPI DSTN DVD ECP EPROM FAT FCC GB HDD HTML IEEE I/O IRQ ISP KB LAN LCD LPT1 LSI MB MIDI NTFS PC PCI PCMCIA
direct memory access dual inline memory module disk operating system dots per inch dual supertwist nematic digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory file allocation table Federal Communications Commission gigabyte hard disk drive Hypertext Markup Language Institute of Electrical and Electronics Engineers input/output interrupt request Internet service provider kilobyte local area network liquid crystal display line printer port 1 (parallel port) large-scale integration megabyte Musical Instrument Digital Interface NT file system personal computer Peripheral Component Interconnect Personal Computer Memory Card International Association
Glossary
221
RAM RFI ROM RTC SCSI SDRAM SRAM SVGA TFT USB URL WAN www
random access memory radio frequency interference read-only memory real-time clock small computer system interface synchronous dynamic random access memory static random access memory super video graphics adapter thin film transistor universal serial bus uniform resource locator wide area network World Wide Web
Terms
The following terms may appear in this users guide.
active-matrix display A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a TFT display, in its simplest form there is one thin film transistor (TFT) for each cell. This type of display works well with notebook computers because of its shallow depth and high-quality color. Active-matrix displays are viewable from wider angles than most passive-matrix displays. adapter A device that provides a compatible connection between two units. For example, the computers internal display adapter receives information from the software and translates it into images on the screen. An adapter can take a number of forms, from a microprocessor to a simple connector. An intelligent adapter (one that is capable of doing some processing) may also be called a controller. alternating current (AC) The type of power usually supplied to residential and commercial wall outlets. AC reverses its direction at regular intervals. Compare direct current (DC).
222
Glossary
application A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program.
backup A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged. basic input/output system (BIOS) See BIOS. baud rate The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second). See also bits per second. BIOS (basic input/output system) Basic instructions, stored in readonly memory (ROM), containing the information the computer needs in order to check hardware and load the operating system when you start up the computer. bit: Short for binary digit. A bit is the smallest unit of information used by a computer. A group of eight bits is a byte. See also byte. bits per second (bps) A way of measuring the speed at which information is passed between two devices. The basic measure used in modem communications, bps is similar, but not identical, to the baud rate. See also baud rate. boot To start the computer. The term boot originates from bootstrap program (as in pulling itself up by its bootstraps), a program that loads and initializes the operating system. See also reboot. boot disk See system disk. boot priority (startup sequence) The order in which the computer accesses its disk drives to locate the startup files. Under the default startup sequence, the computer looks for the startup files in the diskette drive before checking the hard disk. bus An electrical circuit that connects the central processing unit (CPU) with other parts of the computer, such as the video adapter, disk drives, and ports. It is the pathway through which data flows from one device to another. See also bus speed, frontside bus. bus speed The speed at which the central processing unit (CPU) communicates with the other parts of the computer.
Glossary
223
byte A sequence of eight bits. A byte is the smallest addressable unit of data. See also bit, gigabyte, kilobyte, megabyte.
cache A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computers main memory. See also CPU cache, L1 cache, L2 cache. CD An individual compact disc. See also CD-ROM. CD-ROM (compact disc read-only memory) A form of highcapacity storage that uses laser optics instead of magnetic means for reading data. See also CD. Compare DVD-ROM. central processing unit (CPU) The chip that functions as the brain of the computer. It takes information from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character Any letter, number, or symbol you can use on the computer. Some characters are non-printing characters, such as a paragraph break in a word-processing program. A character occupies one byte of computer storage. chip A small piece of silicon containing computer logic and circuits for processing, memory, input/output, and/or control functions. Chips are mounted on printed circuit boards. click To press and release the TouchPad control button or mouse button without moving the cursor or mouse. In the Windows operating system, this refers to the left mouse button or primary TouchPad control button, unless otherwise stated. See also doubleclick. color palette A set of specified colors that establishes the colors that can be displayed on the screen at a particular time. compatibility The extent to which computers, programs, or devices can work together harmoniously, using the same commands, formats, or language as another. configuration (1) The collection of components that make up a single computer system. (2) How parts of the system are set up (that is, configured).
224
Glossary
controller A device that controls the transfer of data from a computer to a peripheral device and vice versa. For example, disk drives, monitors, keyboards, and printers all require controllers. CPU See central processing unit (CPU). CPU cache A section of very fast memory residing between the CPU and the computers main memory that temporarily stores data and instructions the CPU will need to execute commands and programs. See also cache, L1 cache, L2 cache. cursor A symbol that indicates the current position on the screen. The shape of the cursor varies, depending on the program youre using and what youre doing.
default The setting selected by a program when the user does not specify an alternative setting. device A component attached to the computer. Devices may be external (outside the computers case) or internal (inside the computers case). Printers, disk drives, and modems are examples of devices. device driver A program (called a driver) that permits a computer to communicate with a device. dialog box An on-screen window displayed by the operating system or a program giving a direction or requesting input from the user. direct current (DC) The type of power usually supplied by batteries. DC flows in one direction. Compare alternating current (AC). direct memory access (DMA) A dedicated channel, bypassing the CPU, that enables direct data transfer between memory and a device. directory See folder. disable To turn a computer option off. See also enable. disc A round, flat piece of metal, designed to be read from and written to by optical (laser) technology, and used in the production of optical discs, such as CDs and DVDs. Compare disk.
Glossary
225
disk A round, flat piece of material that can be magnetically influenced to hold information in digital form, and used in the production of magnetic disks, such as diskettes and hard disks. Compare disc. See also diskette, hard disk. disk drive The device that reads and writes information and programs on a diskette or hard disk. It rotates the disk at high speed past one or more read/write heads. diskette A thin, flexible disk in a protective jacket that stores magnetically encoded data. Diskettes can be removed from the computer and come in two sizes: 5.25-inch and 3.5-inch. Your computer uses 3.5-inch diskettes. See also double-density diskette, high-density diskette. document Any file created with an application and, if saved to disk, given a name by which it can be retrieved. See also file. double-click To press the TouchPad control button or mouse button rapidly twice without moving the cursor or mouse. In the Windows operating system, this refers to the primary TouchPad control button or left mouse button, unless otherwise stated. download (1) In communications, to receive a file from another computer through a modem or network. (2) To send font data from the computer to a printer. See also upload. drag To hold down the TouchPad control button or mouse button while moving the cursor to drag a selected object. In the Windows operating system, this refers to the primary TouchPad control button or left mouse button, unless otherwise stated. driver See device driver. DVD An individual digital versatile (or video) disc. See also DVDROM. DVD-ROM (digital versatile [or video] disc read-only memory) A very high-capacity storage medium that uses laser optics for reading data. Each DVD-ROM can hold as much data as several CD-ROMs. Compare CD-ROM.
226
Glossary
enable To turn on a computer option. See also disable. executable file A computer program that is ready to run. Application programs and batch files are examples of executable files. Names of executable files usually end with a .bat or .exe extension. extension See file extension. external device See device.
file A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also document. file allocation table (FAT) The section of a disk that keeps track of the location of files stored on the disk. file name A set of characters that uniquely identifies a file within a particular folder. It consists of two parts: the actual name and the file name extension. See also file extension. file extension The three characters following the period (pronounced dot) at the end of a file name. The extension indicates the type of file. Examples are .exe for program files and .hlp for help files. See also file name. folder Also called directory. A container for organizing files saved to a disk. A folder is symbolized on screen by a graphical image (icon) of a file folder. A folder can contain files and other folders. format (verb) To prepare a blank disk for use with the computers operating system. Formatting creates a structure on the disk so the operating system can write information to the disk or read information from it. frontside bus The primary pathway (bus) between the CPU and the computers main memory. Also called system bus. See also bus. function keys The keys labeled F1 through F12, typically located on the keyboard. Their function is determined by the operating system and/or individual programs.
gigabyte (GB) A unit of data equal to 1,073,741,824 bytes (1024 x 1024 x 1024 bytes). See also byte.
Glossary
227
ground A conductor to which all components of an electric circuit are connected. It has a potential of zero (0) volts, is connected to the earth, and is the point of reference for voltages in the circuit.
hard disk A storage device composed of a rigid platter or platters that can be magnetically coded with data. Hard disks hold much more information than diskettes and are used for long-term storage of programs and data. The primary (or only) hard disk in a computer is usually fixed, but some computers have secondary hard disks that are removable. By default, the hard disk is referred to as drive C. hardware The physical components of a computer system. Compare software. Hibernate A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off. See also Standby, Suspend. high-density diskette A 3.5-inch diskette that holds 1.44 MB of data. See also diskette. hot key (1) A feature in which certain keys in combination with the Fn key can set system options or control system parameters, such as the battery save mode. (2) A key or combination of keys that activates a memory resident program. hot swapping The ability to add or remove devices from a computer while the computer is running and have the operating system automatically recognize the change.
icon A small image displayed on the screen that represents a function, file, or program. interlaced A method of refreshing a computer screen, in which only every other line of pixels is refreshed. Interlaced monitors take two passes to create a complete screen image. Compare non-interlaced. internal device See device. Internet The decentralized, world-wide network of computers that provides electronic mail, the World Wide Web, and other services. See also World Wide Web.
228
K L
Glossary
keyboard shortcut A key or combination of keys that you use to perform a task instead of using a pointing device such as the TouchPad. kilobyte (KB) A unit of data equal to 1024 bytes. See also byte. L1 (level one) cache Memory cache built into the processor to help improve processing speed. See also cache, CPU cache, L2 cache. L2 (level two) cache Memory cache installed on the motherboard to help improve processing speed. It is slower than L1 cache and faster than main memory. See also cache, CPU cache, L1 cache. LAN (local area network) A group of computers or other devices dispersed over a relatively limited area and connected by a communications link that enables any device to interact with any other on the network. liquid crystal display (LCD) A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it. A filter over the electrodes permits only non-polarized light to pass to the surface of the display, creating light and dark pixels. load To move information from a storage device (such as a hard disk) into memory for processing. local area network See LAN. logical drive A section of a disk that is recognized by the operating system as a separate disk drive. A systems logical drives may differ from its physical drives. For example, a single hard disk drive may be partitioned into two or more logical drives.
megabyte (MB) A unit of data equal to 1,048,576 bytes (1024 x 1024 bytes). See also bytes. memory Typically refers to the computers main memory, where programs are run and data is temporarily stored and processed. Memory can be volatile and hold data temporarily, such as RAM, or it can be nonvolatile and hold data permanently, such as ROM. A computers main memory is RAM. See RAM, ROM.
Glossary
229
microprocessor See central processing unit (CPU). MIDI (Musical Instrument Digital Interface) A standard for connecting musical instruments, synthesizers, and computers. The MIDI standard provides a way of translating music into a form computers can use, and vice versa. modem Short for modulator/demodulator. A device that converts information from digital to analog and back to digital, enabling information to pass back and forth between digital computers and analog telephone lines. motherboard The main circuit board in the computer. It contains the processor, memory, and other primary components. MS-DOS prompt See system prompt. multimedia A combination of two or more media, such as sound, animation, and video in a computer program or presentation. multi-function drive -- A DVD drive that can read and write to CD and DVD media. Musical Instrument Digital Interface See MIDI.
network A collection of computers and associated devices that are connected by communications facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to exchange electronic mail. non-interlaced A method of refreshing a computer screen, in which each pixel of every line is refreshed as the electron beam scans across and down the screen. Compare interlaced. non-system disk A disk for storing programs and data that cannot be used to start the computer. Compare system disk. NT file system (NTFS) An advanced file system designed for use specifically with the Windows NT operating system.
online Available through the computer. Online may refer to information being read from your own computers hard disk, such as online documentation or online help, or to information coming from another company on a company network or the Internet.
230
Glossary
operating system A set of programs that controls how the computer works. Examples of operating systems are Windows 98 Second Edition and Windows 2000 operating systems.
palette See color palette. parallel Processes that occur simultaneously. In communications, it means the transmission of more than one bit of information at a time. On your computer, the parallel port provides a parallel communications interface between the computer and an appropriate device. Most modern printers are parallel. Compare serial. password A unique string of characters entered by a user to verify his or her identity to the computer or the network. PC Card A credit-card-sized expansion card designed to increase the capabilities of notebook computers. PC Cards provide functions such as modem, fax/modem, hard disk drive, network adapter, sound card, or SCSI adapter. peripheral Any device, such as a printer or joystick, that is attached to the computer and controlled by the computers CPU. pixel Short for picture element. The smallest dot that can be produced on a screen or printer. Plug and Play Generally, refers to the computers ability to automatically configure itself to work with peripheral devices. When capitalized, refers to a standard that, when followed by a device manufacturer, allows a PC to configure itself automatically to work with the device. pointing device Any device, such as the TouchPad or a mouse, that enables you to move the cursor on the screen. port A socket on the computer where you plug in a cable for connection to a network or a peripheral device. processor See central processing unit (CPU). program A set of instructions that can be executed by a computer. The general classes of programs (also called software) are operating system, application, and utility. See also operating system, application, utility.
Glossary
231
properties The attributes of an object or device. For example, the properties of a file include the files type, size, and creation date.
RAM (random access memory) Volatile memory that can be written to as well as read. By volatile, we mean that information in RAM is lost when you turn off your computer. This type of memory is used for your computers main memory. See also memory. Compare ROM. random access memory See RAM. read-only memory See ROM. reboot See boot, restart. removable disk A disk that can be removed from a disk drive. A diskette is one example of a removable disk. resolution A measure of the sharpness of the images that can be produced by a printer or displayed on a screen. For a printer, resolution is expressed in dots per inch (dpi). For a screen, it is expressed as the number of pixels available horizontally and vertically. restart Synonymous with reboot. To reset the computer by reloading the operating system without turning the computer off. See also boot. RJ-11 A modular connector used on most U.S. telephone systems and direct-connect modems. The RJ-11 connector is a 6-wire connector. RJ-45 A connector used to attach computers to LANS (local area networks) and to link ISDN (Integrated Services Digital Network) devices to NT-1 (Network Terminator devices). Also called. ROM (read-only memory) Non-volatile memory that can be read but not written to. By non-volatile, we mean that information in ROM remains whether or not the computer is receiving power. This type of memory is used to store your computers BIOS, which is essential instructions the computer reads when you start it up. See also BIOS, memory. Compare RAM.
select To highlight or otherwise specify text, data, or graphics with the intent to perform some operation on it.
232
Glossary
serial Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel. On your computer, the serial port provides a serial interface between the computer and an appropriate device. Compare parallel. shortcut See keyboard shortcut. software See program. Compare hardware. Standby A feature of some Windows operating systems that allows you to turn off the computer without exiting your open applications and to continue from where you left off when you turn the computer on again. Suspend A feature of some Windows operating systems that allows you to turn off the computer without exiting your open applications and to continue from where you left off when you turn the computer on again. system disk A diskette that contains the operating system files needed to start the computer. Any diskette can be formatted as a system disk. A system disk is also called a bootable disk or a startup disk. Compare non-system disk. system prompt The symbol (in the MS-DOS operating system, generally a drive letter followed by a greater than sign) indicating where users are to enter commands.
T U
TFT display See active-matrix display. Universal Serial Bus (USB) 2.0 A serial bus that supports peripherals such as keyboards and pointing devices. USB peripherals have a single standard for cables and connectors. The USB standard also allows hot swapping of peripherals. See also bus, hot swapping, serial. upload To send a file to another computer through a modem or network. See also download. USB See universal serial bus (USB). utility A computer program designed to perform a narrowly focused operation or solve a specific problem. Utilities are often related to computer system management.
Glossary
233
Web See World Wide Web. Wi-Fi A trademarked term by the Wireless Capability Ethernet Alliance which stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www) The worldwide network of Web sites linked together over the Internet. A user of the Web can jump from site to site regardless of the location of the computer hosting the site. See also Internet.
Index
A
AC adapter 48 AC power light 48, 50 accessories memory 62 alarms low battery 124 audio features 145 Auto-Run 98 avoiding injury 40 removing 125 button start 134 buttons CD controls 94 CD Player 98 CD/DVD controls 93 DVD-ROM or multi-function drive eject 93 primary control 56 secondary control 56
B
battery alarms 124 caring for 128 changing 125 charge not lasting 178 charging 51, 75, 119 disposal 130 installing 125 light 50, 121 monitoring power 121 power usage mode 199
C
cards PC 148 CD creating 99 playing using Auto-Run 98 CD and DVDs caring for 101 viewing contents 99 CD control buttons 94 CD Player control panel 98 CD/DVD control buttons 93
234
235
CDs inserting 95 problem solving 185 channels DMA 172 IRQ 172 charging main battery 51, 119 checking device properties 174 cleaning CD or DVDs 101 computer 76 comfort chair 42 lighting 42 work habits 43 command Shut down 102 Turn Off 102 commands Hibernate 103 powering down 101 Standby 104 communications network connection 138 system resources 172 compact discs inserting 95 problem solving 185 removing 100 computer cleaning 76 lock 77 moving 77 non-system disk or disk error message 168 not accessing disk drives 168 placement 41 protection 39 running on battery power 116 setting up 46, 63 turning on 53 warning resume failure message
168
work area 39 computing tips 79 connecting AC adapter 48 external monitor 73 external speakers 148 mouse 68 power cable 50 USB mouse 68 USB-compatible keyboard 68 connection set up 139 Contents CDs 99 DVDs 99 control buttons for DVD-ROM or multifunction drive 94 critical applications 2
D
DC-IN 50 desktop creating new icon 133 major features 133 desktop exploration 132 desktop icons 133 Device Manager 174 checking properties 174 disabling a device 174, 175 devices keyboard 68 dial-up connection 139 Dial-Up Networking Wizard 139 disable/enable
236
TOSHIBA Touch and Launch 61 disabling/enabling TouchPad 56 Disk Defragmenter 183 disk drive corrupted/damaged data files 183 missing files/trouble accessing a disk 182 running slow 183 diskette drive 72 cannot insert a diskette 183 cannot read a diskette 184 external 72 display does not look normal/flickers 180 external monitor not working 181 external, adjusting 74 hot key 73 latch 52 screen is blank 179 display limitations 74 display panel opening 52 Display settings hot key 145 disposal information 27 disposing of used batteries 130 DMA (Direct Memory Access) 172 double-click 56 DVD-ROM start drive 145 DVD-ROM drive 145 problems 184 removing a disc 100 troubleshooting 175 DVD-ROM or multi-function drive eject button 93 inserting discs 95 DVD-ROM or multifunction drive control buttons 94 inserting a disc 94 removing 100 DVDs playing 145
E
energy saving features 116 environmental considerations 40, 41 ergonomics lighting 42 posture 41 seating guidelines 42 work habits 43 error messages device driver conflict 171 general hardware problem 171 non-system disk or disk error
168, 183
problem with display settings/ current settings not working with hardware 180 program has performed an illegal operation 166 warning resume failure 168 Error-checking 182 exploring the desktop 132 external diskette drive 72 keyboard 68 external monitor not working 181 external speakers 148
F
FAT (File Allocation Table) 182 FCC Notice Declaration of Conformity Information 3 FCC requirements 4 file extensions 89
237
file names 89 files backing up 80, 91 printing 90 restoring 91 saving 79, 88 Fn key assigning functions 154 Fn-esse 153 assigning keys 154 change/remove key assignments volume mute 197 hot keys display brightness 202 keyboard functions 203 hot swapping precautions 150 Hotkey utility 157
I
i.LINK FCC 3 icon 133 desktop 133 internet explorer 134 moving to desktop 133 recycle bin 134 safety 37 Industry Canada requirement 4 inserting CDs and DVDs 95 PC Cards 148 installing main battery 125 Internal mode 181 Internet bookmarked site not found 170 connecting to 141 features 143 overview 140 slow connection 170 surfing 142 uploading and downloading files
156
drag-and-drop 154 keyboard 153 starting 153 using keyboard 155 viewing key assignments 156 function keys 82
H
hard disk drive light 54 hardware conflicts 171 resolving 173 Help Windows XP 170 Hibernate restarting 112 using 108 Hibernation 103 Hibernation mode 76 methods 108 hot key disable/enable TouchPad 203 display modes 202 display output settings 73 display settings 145 instant password 197 power usage mode 199 Stand by mode 200
143
URL address not found 170 internet explorer icon 134 Internet Service Providers 141 IRQ (Interrupt Request) 172 ISPs 141
238
J
jack RJ-11 138 determining COM port 136 problem solving 191 resetting port to default settings
137
upgrading 137 module Wi-Fi Mini PC 140 monitor connecting 73 not working 180 mouse connecting 68 moving the computer 77 multi-function drive 145 cannot access disc 184 drive tray will not open 184 problems 184 start 145 troubleshooting 175
K
keyboard character keys 81 Ctrl, Fn, and Alt keys 82 cursor control overlay 84 external 68 Fn-esse 153 function keys 82 hot keys 203 not working 167, 179 numeric keypad overlay 83 overlay keys 83 unexpected characters 178 Windows special keys 82
L
lights AC power 48, 50 battery 50, 121 hard disk drive 54
N
network accessing 138 dial-up connection 139 Dial-Up Networking Wizard 138 networking wireless 138
M
main battery changing 125 removing 125 memory accessing modules 64 accessing slots 64 checking total 68 problem solving 176 removing 66, 67 verifying 68 Microsoft Support Online Web site
P
password instant 197 power-on 54 PC Card checklist 188 CIS (Card Information Structure)
187
computer stops working 189 errors 189 hot swapping fails 189 inserting 148
171
modem
239
modem default 136 not recognized 189 problem solving 187, 188 removing 149 replacing 150 PC Cards using 148 PCMCIA (Personal Computer Memory Card International Association) 148 Plug and Play 173 port COM 136 ports external diskette drive 72 power cable 50 cable connectors 204 computer will not start 167 monitoring 121 problem solving 177 taking care of your battery 128 Power Management 159 powering down 101 power mode creating new 161 customizing 161 power usage modes 123 power-on password 54 precautions 44 primary control button 56 printer Add Printer Wizard 70 problem solving 190 printing a file 90 problem solving AC power 177 accessing disk drives 168 battery charge does not last 178 cannot access CD/DVD 184 cannot insert diskette in drive 183 cannot read a diskette 184 changing display properties 180 checking device properties 174 compact discs not running correctly 185 computer hangs when PC Card inserted 189 computer will not power up 167 contacting Toshiba 193 corrupted/damaged data files 183 Device Manager 174 disabling a device 174, 175 disk drive is slow 183 display is blank 179 external display not working 181 external keyboard not working
179
external monitor 180 faulty memory 176 hardware conflict 171, 172 hardware conflict caused by legacy device 173 high-pitched noise 186 illegal operation 166 Internet bookmarked site not found 170 Internet connection is slow 170 keyboard not responding 167 keyboard produces unexpected characters 178 missing files/trouble accessing a disk 182 modem not receiving or transmitting 191 multi-function drive tray does not eject 184 no sound 186
240
non-system disk or disk error
Restart command 103 restarting from Hibernate 112 restarting from Standby 115 restarting from Turn Off 108 RJ-11 jack 138 Run dialog box 86 running the computer on battery power
116
S
safety computer 131 disposing of batteries 130 icons 37 precautions 44 saving your work 88 screen blank 179 does not look normal/flickers 180 secondary control button 56 security fitting a computer lock cable 77 instant password 197 setting battery alarms 124 setting up AC adapter 48 computer 39, 46, 63 printer 70 TOSHIBA Touch and Launch 60 setting up a connection 139 settings TOSHIBA Touch and Launch 60 Shut down using 105 shut down 76 Shut down command 102 sound .wav files 146 problem solving 186
183
screen does not look right/flickers
180
system resources 172 trouble prevention 192 URL address not found 170 using Startup options 169 warning resume failure 168 Windows XP not working 168 Windows XP will not start 168 programs not running correctly 183 starting 84 protection of stored data 2
R
recharging main battery 119 recording adjusting quality 147 sounds 146 Recovery Media 38 recycle bin icon 134 removing CDs and DVDs 100 main battery 125 PC Cards 149
241
speakers external 148 Stand by command 112 Stand by mode hot key 200 Standby 104 low battery 124 restarting 115 using 112 start button 134 starting a program 84 Run dialog box 86 Windows Explorer 85 Windows Start menu 85 starting up the computer from Standby 115 Startup menu problem solving 169 sticky key 152 stored data protection 2 System Setup 168 system tools 182 Disk Defragmenter 183 Error-checking 182 system tray 135 Turn Off restarting from 108 using 105 Turn Off command 102 Turn Off methods 106 turning computer on/off 53
U
Universal Resource Locator (URL)
135
USB mouse connecting 68 USB-compatible keyboard connecting 68 using Hibernate 108 Standby 112 using a file extension 89 utilities Fn-esse 153 Hotkey utility 157 Power Management 159 TOSHIBA Accessibility 152 TOSHIBA Console 157 Toshiba Hardware Setup 161
T
taskbar 135 Toshiba Internet Web sites 195 Toshiba Accessories information 38 TOSHIBA Console 157 Toshiba Hardware Setup 161 TOSHIBA Touch and Launch 58 disable/enable 61 TouchPad disabling/enabling 56 traveling tips 131
V
video features exploring 144
W
warranty Toshiba Services 38 Web sites Support Online 171 Web sites,Toshiba 195 Wi-Fi wireless networking 138 Wi-Fi Mini PCI modules 140
242
Windows Explorer 85 Windows Media Player 96 Windows Standby 75 Windows Start menu 85 Windows XP Help 170 Help and Support 171 problem solving 168 Windows XP Professional taskbar 135 Windows XP Professional desktop
132
wireless interoperability 7 wireless networking 138 Wizards Add Printer 70 Dial-Up Networking Wizard 138
Z
Zooming Utility 163