SAFETY DATA SHEET

MOBILGREASE XHP 222

Section 1. Identification
Product name : MOBILGREASE XHP 222
Product description : base oil and additives

Relevant identified uses of the substance or mixture and uses advised against
Identified uses : grease
Uses advised against : This product is not recommended for any industrial, professional or consumer use other
than the identified uses above.

Supplier : EXXON MOBIL CORPORATION

22777 Springwoods Village Parkway
Spring, TX 77389 USA

24-Hour emergency : 1-800-424-9300 / +1 703-741-5970 / +1-703-527-3887 (CHEMTREC)

telephone number
Product Technical : 800-662-4525
Information

SDS Internet Address : www.sds.exxonmobil.com

Section 2. Hazards identification

OSHA/HCS status : While this material is not considered hazardous by the OSHA Hazard Communication
Standard (29 CFR 1910.1200), this SDS contains valuable information critical to the
safe handling and proper use of the product. This SDS should be retained and available
for employees and other users of this product.
Classification of the : Not classified.
substance or mixture

Hazards not otherwise : None known.

classified
Note : This material should not be used for any other purpose than the intended use in Section
1 without expert advice. Health studies have shown that chemical exposure may cause
potential human health risks which may vary from person to person.

Section 3. Composition/information on ingredients

Substance/mixture : Mixture

Ingredient name % by weight Identifiers

benzenamine, n-phenyl-, reaction products with 2,4,4-trimethylpentene ≤3 CAS: 68411-46-1

zinc dialkyl dithiophosphate <2 CAS: 68457-79-4

naphthenic acids, zinc salts <1 CAS: 12001-85-3

1h-benzotriazole-1-methanamine, n,n-bis(2-ethylhexyl)-ar-methyl- ≤0.3 CAS: 94270-86-7

naphthalenesulfonic acid, dinonyl-, calcium salt ≤0.3 CAS: 57855-77-3

Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified and hence require reporting in this section.

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 1/11
MOBILGREASE XHP 222

Section 3. Composition/information on ingredients

Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures

Description of necessary first aid measures
Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Get medical attention if irritation
occurs.
Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Get medical attention if symptoms occur. If product is injected into or under the
skin, or into any part of the body, regardless of the appearance of the wound or its size,
the individual should be evaluated immediately by a physician as a surgical emergency.
Even though initial symptoms from high pressure injection may be minimal or absent,
early surgical treatment within the first few hours may significantly reduce the ultimate
extent of injury.
Ingestion : Wash out mouth with water. If material has been swallowed and the exposed person is
conscious, give small quantities of water to drink. Do not induce vomiting unless
directed to do so by medical personnel.

Most important symptoms/effects, acute and delayed

Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : No specific data.
Inhalation : No specific data.
Skin contact : Local necrosis as evidenced by delayed onset of pain and tissue damage a few hours
after injection.
Ingestion : No specific data.

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : No specific treatment.
Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training.

See toxicological information (Section 11)

Section 5. Fire-fighting measures

Extinguishing media
Suitable extinguishing : Use dry chemical, CO₂, water spray (fog) or foam.
media
Unsuitable extinguishing : Do not use water jet.
media

Specific hazards arising : This material is harmful to aquatic life. Fire water contaminated with this material must
from the chemical be contained and prevented from being discharged to any waterway, sewer or drain.
Hazardous combustion : Aldehydes, Incomplete combustion products, Oxides of carbon, Smoke, Fume, sulfur
products oxides

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 2/11
MOBILGREASE XHP 222

Section 5. Fire-fighting measures

Special protective actions : Use standard firefighting procedures and consider the hazards of other involved
for fire-fighters materials. Promptly isolate the scene by removing all persons from the vicinity of the
incident if there is a fire. Assure an extended cooling down period to prevent re-ignition.
Prevent runoff from fire control or dilution from entering streams, sewers, or drinking
water supply. No action shall be taken involving any personal risk or without suitable
training.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained breathing
equipment for fire-fighters apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Section 6. Accidental release measures

NOTIFICATION PROCEDURES
In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations. US
regulations require reporting releases of this material to the environment which exceed the applicable reportable quantity
or oil spills which could reach any waterway including intermittent dry creeks. The National Response Center can be
reached at (800)424-8802.

Personal precautions, protective equipment and emergency procedures

For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Put on appropriate personal
protective equipment.
For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".

Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to
the environment if released in large quantities.

Methods and materials for containment and cleaning up

Small spill : Move containers from spill area. Vacuum or sweep up material and place in a
designated, labeled waste container. Dispose of via a licensed waste disposal
contractor.
Large spill : Move containers from spill area. Approach release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Vacuum or sweep up material
and place in a designated, labeled waste container. Dispose of via a licensed waste
disposal contractor. Confine the spill immediately with booms. Skim from surface.
Warn other shipping. Note: see Section 1 for emergency contact information and
Section 13 for waste disposal.
Water spill and land spill recommendations are based on the most likely spill scenario for this material; however,
geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may
greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local
regulations may prescribe or limit action to be taken.

Section 7. Handling and storage

Precautions for safe handling
Protective measures : Put on appropriate personal protective equipment (see Section 8). Do not ingest. Avoid
contact with eyes, skin and clothing. Avoid release to the environment. Keep in the
original container or an approved alternative made from a compatible material, kept
tightly closed when not in use. Empty containers retain product residue and can be
hazardous. Do not reuse container.
Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
Static Accumulator : This material is not a static accumulator.

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 3/11
MOBILGREASE XHP 222

Section 7. Handling and storage

Conditions for safe storage, : Store in accordance with local regulations. Store in original container protected from
including any direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials
incompatibilities (see Section 10) and food and drink. Keep container tightly closed and sealed until
ready for use. Containers that have been opened must be carefully resealed and kept
upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination. See Section 10 for incompatible
materials before handling or use.

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits
solvent dewaxed heavy paraffinic distillate NIOSH REL (United States, 10/2020) [OIL MIST MINERAL]
TWA 10 hours: 5 mg/m³. Form: Mist.
STEL 15 minutes: 10 mg/m³. Form: Mist.
OSHA PEL (United States, 5/2018) [Oil mist, mineral]
TWA 8 hours: 5 mg/m³.
ACGIH TLV (United States, 1/2024) [Mineral Oil, pure, highly and
severely refined]
TWA 8 hours: 5 mg/m³. Form: Inhalable fraction.
solvent dewaxed residual oil (petroleum) NIOSH REL (United States, 10/2020) [OIL MIST MINERAL]
TWA 10 hours: 5 mg/m³. Form: Mist.
STEL 15 minutes: 10 mg/m³. Form: Mist.
OSHA PEL (United States, 5/2018) [Oil mist, mineral]
TWA 8 hours: 5 mg/m³.
ACGIH TLV (United States, 1/2024) [Mineral Oil, pure, highly and
severely refined]
TWA 8 hours: 5 mg/m³. Form: Inhalable fraction.
severely hydrotreated heavy paraffinic distillate NIOSH REL (United States, 10/2020) [OIL MIST MINERAL]
TWA 10 hours: 5 mg/m³. Form: Mist.
STEL 15 minutes: 10 mg/m³. Form: Mist.
OSHA PEL (United States, 5/2018) [Oil mist, mineral]
TWA 8 hours: 5 mg/m³.
ACGIH TLV (United States, 1/2024) [Mineral Oil, pure, highly and
severely refined]
TWA 8 hours: 5 mg/m³. Form: Inhalable fraction.
benzenamine, n-phenyl-, reaction products with None.
2,4,4-trimethylpentene
zinc dialkyl dithiophosphate None.
naphthenic acids, zinc salts None.
1h-benzotriazole-1-methanamine, n,n-bis None.
(2-ethylhexyl)-ar-methyl-
naphthalenesulfonic acid, dinonyl-, calcium salt None.
NOTE: Limits/standards shown for guidance only. Follow applicable regulations.

Appropriate engineering : Good general ventilation should be sufficient to control worker exposure to airborne
controls contaminants.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 4/11
MOBILGREASE XHP 222

Section 8. Exposure controls/personal protection

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: safety glasses with side-
shields.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Body protection : Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product.
Other skin protection : Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Respiratory protection : Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.

Section 9. Physical and chemical properties and safety characteristics

Note: Physical and chemical properties are provided for safety, health and environmental considerations only
and may not fully represent product specifications. Contact the Supplier for additional information.
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.

Appearance
Physical state : Liquid. [Semi-fluid]
Color : Dark Blue
Odor : Characteristic
Odor threshold : Not available.
pH : Not applicable.
Melting point/freezing point : Not available.
Boiling point or initial : >315.56°C (>600°F)
boiling point and boiling
range
Flash point : Open cup: >200°C (>392°F) [EST. FOR OIL, ASTM D-92 (COC)]
Evaporation rate : Not available.
Flammability : Ignitable
Lower and upper explosion : Not available.
limit/flammability limit
Vapor pressure : <0.1 mm Hg [20 °C]
Relative vapor density : Not available.
Relative density : 0.88
Solubility in water : Negligible
Partition coefficient: n- : >3.5
octanol/water

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 5/11
MOBILGREASE XHP 222

Section 9. Physical and chemical properties and safety characteristics

Auto-ignition temperature : Not available.
Decomposition temperature : Not available.
Viscosity : 220 cSt [40 °C]
Particle characteristics
Median particle size : Not applicable.
DMSO Extract (mineral oil : <3 % by weight
only), IP-346

Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.

Chemical stability : The product is stable.

Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions

Conditions to avoid : High energy sources of ignition. Excessive heat.

Incompatible materials : Strong oxidizers

Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products should
products not be produced.

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Product/ingredient name Test Species Result Duration
1h-benzotriazole- LD50 Oral Rat 3313 mg/kg -
1-methanamine, n,n-bis
(2-ethylhexyl)-ar-methyl-
Conclusion/Summary
Inhalation : Minimally Toxic. No end point data for material. Based on assessment of the
components.
Dermal : Minimally Toxic. No end point data for material. Based on assessment of the
components.
Oral : Minimally Toxic. No end point data for material. Based on assessment of the
components.
Irritation/Corrosion
Conclusion/Summary
Skin : Negligible irritation to skin at ambient temperatures. No end point data for material.
Based on assessment of the components.
Eyes : May cause mild, short-lasting discomfort to eyes. No end point data for material. Based
on assessment of the components.
Respiratory : Negligible hazard at ambient/normal handling temperatures. No end point data for
material.
Respiratory or skin sensitization
Conclusion/Summary
Skin : Not expected to be a skin sensitizer. No end point data for material. Based on
assessment of the components.
Respiratory : Not expected to be a respiratory sensitizer. No end point data for material.
Mutagenicity

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 6/11
MOBILGREASE XHP 222

Section 11. Toxicological information

Conclusion/Summary : Not expected to be a germ cell mutagen. No end point data for material. Based on
assessment of the components.
Carcinogenicity
Conclusion/Summary : Not expected to cause cancer. No end point data for material. Based on assessment of
the components.
Reproductive toxicity
Conclusion/Summary : Not expected to be a reproductive toxicant. No end point data for material. Based on
assessment of the components.
Specific target organ toxicity (single exposure)
Conclusion/Summary : Not expected to cause organ damage from a single exposure. No end point data for
material.
Specific target organ toxicity (repeated exposure)
Product/ingredient name Category Target organs
MOBILGREASE XHP 222 Not applicable. -
Conclusion/Summary : Not expected to cause organ damage from prolonged or repeated exposure. No end
point data for material. Based on assessment of the components.
Aspiration hazard
Conclusion/Summary : Not expected to be an aspiration hazard. Based on physico-chemical properties of the
material. Data available.

Other information
Contains : C.I. Solvent blue: Positive in the Ames and Mouse Lymphoma mutagenicity assay. Base
oil severely refined: Not carcinogenic in animal studies. Representative material passes
IP-346, Modified Ames test, and/or other screening tests. Dermal and inhalation studies
showed minimal effects; lung non-specific infiltration of immune cells, oil deposition and
minimal granuloma formation. Not sensitizing in test animals.

Section 12. Ecological information

The information given is based on data for the material, components of the material, or for similar materials, through the
application of bridging principals.
Toxicity
Conclusion/Summary
Acute toxicity : Harmful to aquatic life.
Chronic toxicity : Not expected to demonstrate chronic toxicity to aquatic organisms.
Persistence and degradability
Biodegradability : Base oil component -- Expected to be inherently biodegradable
Bioaccumulative potential
Conclusion/Summary : Base oil component -- Has the potential to bioaccumulate, however metabolism or
physical properties may reduce the bioconcentration or limit bioavailability.
Mobility in soil
Mobility : Base oil component -- Expected to partition to sediment and wastewater solids. Low
solubility and floats and is expected to migrate from water to the land.
Other ecological information
Other adverse effects : No known significant effects or critical hazards.

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 7/11
MOBILGREASE XHP 222

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
Empty Container Warning (where applicable): Empty containers may contain residue
and can be dangerous. Do not attempt to refill or clean containers without proper
instructions. Empty drums should be completely drained and safely stored until
appropriately reconditioned or disposed. Empty containers should be taken for recycling,
recovery, or disposal through suitably qualified or licensed contractor and in accordance
with governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE,
SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME,
SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY
EXPLODE AND CAUSE INJURY OR DEATH.

Section 14. Transport information

DOT Classification TDG Classification IMDG IATA
UN number Not regulated. Not regulated. Not regulated. Not regulated.

UN proper shipping - - - -
name
Transport hazard - - - -
class(es)
Label(s) / Marks

Packing group - - - -
Environmental No. No. No. No.
hazards
Additional information
DOT Classification : Reportable quantity 571.55 lbs / 259.49 kg [77.896 gal / 294.87 L]. Package sizes
shipped in quantities less than the product reportable quantity are not subject to the RQ
(reportable quantity) transportation requirements.

Special precautions for user : Transport within user’s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in the
event of an accident or spillage.

Transport in bulk according : Not applicable.

to IMO instruments

Section 15. Regulatory information

U.S. Federal regulations : TSCA 4(a) proposed test rules: 1h-benzotriazole
TSCA 8(a) PAIR: diphenylamine; naphthalene
TSCA 8(a) CDR Exempt/Partial exemption: Not determined
Clean Water Act (CWA) 307: zinc dialkyl dithiophosphate; naphthenic acids, zinc salts;
zinc neodecanoate; naphthalene
Clean Water Act (CWA) 311: phosphorus; naphthalene; maleic anhydride

TSCA 12(b) - Chemical export notification

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 8/11
MOBILGREASE XHP 222

Section 15. Regulatory information

Not applicable.

Clean Air Act Section 112 : Listed

(b) Hazardous Air
Pollutants (HAPs)
Clean Air Act Section 602 : Not listed
Class I Substances
Clean Air Act Section 602 : Not listed
Class II Substances
DEA List I Chemicals : Not listed
(Precursor Chemicals)
DEA List II Chemicals : Not listed
(Essential Chemicals)
SARA 302/304
Composition/information on ingredients
SARA 302 TPQ SARA 304 RQ
Name % EHS (lbs) (gallons) (lbs) (gallons)
phosphorus ≤0.3 Yes. 100 - 1 -
SARA 304 RQ : 571.6 lbs / 259.5 kg [77.9 gal / 294.9 L]
SARA 311/312
Classification : Not applicable.
SARA 313
Product name CAS number %
Form R - Reporting zinc dialkyl dithiophosphate 68457-79-4 <2
requirements
Supplier notification zinc dialkyl dithiophosphate 68457-79-4 <2

SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include
copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.
State regulations
Massachusetts : The following components are listed: OIL MIST, MINERAL; OIL MIST, MINERAL; OIL
MIST, MINERAL
New York : None of the components are listed.
New Jersey : The following components are listed: ZINC compounds; MINERAL OIL (UNTREATED
and MILDLY TREATED)
Pennsylvania : The following components are listed: ZINC COMPOUNDS
Illinois : None of the components are listed.

Inventory list
Australia inventory (AIIC) : All components are listed or exempted.
Canada inventory (DSL-NDSL) : All components are listed or exempted.
China inventory (IECSC) : All components are listed or exempted.
Japan inventory (CSCL) : All components are listed or exempted.
Japan inventory (Industrial Safety and : All components are listed or exempted.
Health Act)
New Zealand Inventory of Chemicals : All components are listed or exempted.
(NZIoC)
Philippines inventory (PICCS) : All components are listed or exempted.
Korea inventory (KECI) : All components are listed or exempted.
Taiwan Chemical Substances Inventory : All components are listed or exempted.
(TCSI)
Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 9/11
MOBILGREASE XHP 222

Section 15. Regulatory information

United States inventory (TSCA 8b) : All components are active or exempted.

Section 16. Other information

Hazardous Material Information System (U.S.A.)
Health / 0

Flammability 1
Physical hazards 0

Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS®
ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service
mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS®
Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.
National Fire Protection Association (U.S.A.)

1 Flammability
Health 0 0 Instability
Special hazards

Procedure used to derive the classification

Not classified.
New Jersey Right to Know Disclosure
Name CAS #
grease
zinc dialkyl dithiophosphate 68457-79-4
hydrotreated middle distillate (petroleum) 64742-46-7
History
Date of issue/Date of : 16 July 2024
revision
Date of previous issue : 28 November 2023
Version : 1.01
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. ("Marpol" = marine pollution)
N/A = Not available
SGG = Segregation Group
UN = United Nations
References : Not available.
Indicates information that has changed from previously issued version.
Product code : 2015A0202530_1196129
Notice to reader

Date of issue/Date of revision : 16 July 2024 Date of previous issue : 28 November 2023 Version : 1.01 10/11
MOBILGREASE XHP 222

Section 16. Other information

The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief,
accurate and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most
current available from ExxonMobil. The information and recommendations are offered for the user's
consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the
intended use. If buyer repackages this product, it is the user's responsibility to insure proper health, safety and
other necessary information is included with and/or on the container. Appropriate warnings and safe-handling
procedures should be provided to handlers and users. Alteration of this document is strictly prohibited. Except
to the extent required by law, re-publication or retransmission of this document, in whole or in part, is not
permitted. The term, "ExxonMobil" is used for convenience, and may include any one or more of ExxonMobil
Chemical Company, Exxon Mobil Corporation, or any affiliates in which they directly or indirectly hold any interest.