Et200sp DQ 8x24vdc 0 5a ST Manual en-US en-US

Preface
___________________
Documentation guide 1
___________________
2
SIMATIC Product overview
___________________
3
ET 200SP ___________________
Wiring up
Digital output module 4

DQ 8x24VDC/0.5A ST ___________________
Parameters/address space
(6ES7132-6BF01-0BA0)
5
Manual ___________________
Interrupts/diagnostics alarms
6
___________________
Technical specifications
A
___________________
Parameter data record
02/2019
A5E03574575-AF
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Siemens AG A5E03574575-AF Copyright © Siemens AG 2012 - 2019.

Division Digital Factory Ⓟ 03/2019 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Preface
Purpose of the documentation

This manual supplements the system manual ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/58649293).
Functions that generally relate to the system are described in this manual.
The information provided in this manual and in the system/function manuals supports you in
commissioning the system.
Changes compared to previous version

Compared to the previous version, this manual contains the following change:
Technical specifications: Ambient temperature in horizontal and vertical mounting position,
extended to min. -30 °C.
Conventions
CPU: When the term "CPU" is used in this manual, it applies to the CPUs of the S7-1500
automation system as well as to the CPUs/interface modules of the distributed I/O system
ET 200SP.
STEP 7: In this documentation, "STEP 7" is used as a synonym for all versions of the
configuration and programming software "STEP 7 (TIA Portal)".
Please also observe notes marked as follows:
Note
A note contains important information on the product described in the documentation, on the
handling of the product or on the section of the documentation to which particular attention
should be paid.
Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Manual, 02/2019, A5E03574575-AF 3
Preface
Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions constitute one element of such a concept.
Customers are responsible for preventing unauthorized access to their plants, systems,
machines and networks. Such systems, machines and components should only be
connected to an enterprise network or the internet if and to the extent such a connection is
necessary and only when appropriate security measures (e.g. firewalls and/or network
segmentation) are in place.
For additional information on industrial security measures that can be implemented, please
visit (http://www.siemens.com/industrialsecurity).
Siemens' products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends that product updates are applied as soon as they are
available and that the latest product versions are used. Use of product versions that are no
longer supported, and failure to apply the latest updates may increase customers' exposure
to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed visit (http://www.siemens.com/industrialsecurity).

4 Manual, 02/2019, A5E03574575-AF
Table of contents
Preface ................................................................................................................................................... 3
1 Documentation guide .............................................................................................................................. 6
2 Product overview .................................................................................................................................. 10
2.1 Properties ................................................................................................................................10
3 Wiring up .............................................................................................................................................. 12
3.1 Wiring and block diagram .......................................................................................................12
4 Parameters/address space ................................................................................................................... 15
4.1 Parameters .............................................................................................................................15
4.2 Explanation of the parameters ................................................................................................17
4.3 Address space ........................................................................................................................18
5 Interrupts/diagnostics alarms ................................................................................................................. 20
5.1 Status and error display ..........................................................................................................20
5.2 Interrupts .................................................................................................................................22
5.3 Diagnostics alarms ..................................................................................................................22
6 Technical specifications ........................................................................................................................ 23
6.1 Technical specifications ..........................................................................................................23
A Parameter data record .......................................................................................................................... 28
A.1 Parameter assignment and structure of the parameter data record .......................................28

Manual, 02/2019, A5E03574575-AF 5
Documentation guide 1
The documentation for the SIMATIC ET 200SP distributed I/O system is arranged into three
areas.
This arrangement enables you to access the specific content you require.
Basic information
The system manual describes in detail the configuration, installation, wiring and
commissioning of the SIMATIC ET 200SP. distributed I/O system. The STEP 7 online help
supports you in the configuration and programming.
Device information
Product manuals contain a compact description of the module-specific information, such as
properties, wiring diagrams, characteristics and technical specifications.
General information
The function manuals contain detailed descriptions on general topics regarding the SIMATIC
ET 200SP distributed I/O system, e.g. diagnostics, communication, Web server, motion
control and OPC UA.
You can download the documentation free of charge from the Internet
(https://support.industry.siemens.com/cs/ww/en/view/109742709).
Changes and supplements to the manuals are documented in a Product Information.
You can download the product information free of charge from the Internet
(https://support.industry.siemens.com/cs/us/en/view/73021864).

6 Manual, 02/2019, A5E03574575-AF
Documentation guide
Manual Collection ET 200SP

The Manual Collection contains the complete documentation on the SIMATIC ET 200SP
distributed I/O system gathered together in one file.
You can find the Manual Collection on the Internet
(https://support.automation.siemens.com/WW/view/en/84133942).
"mySupport"
With "mySupport", your personal workspace, you make the most of your Industry Online
Support.
In "mySupport" you can store filters, favorites and tags, request CAx data and put together
your personal library in the Documentation area. Furthermore, your data is automatically
filled into support requests and you always have an overview of your current requests.
You need to register once to use the full functionality of "mySupport".
You can find "mySupport" in the Internet (https://support.industry.siemens.com/My/ww/en).
"mySupport" - Documentation
In the Documentation area of "mySupport", you have the possibility to combine complete
manuals or parts of them to make your own manual.
You can export the manual in PDF format or in an editable format.
You can find "mySupport" - Documentation in the Internet
(https://support.industry.siemens.com/My/ww/en/documentation).
"mySupport" - CAx Data

In the CAx Data area of "mySupport", you can have access the latest product data for your
CAx or CAe system.
You configure your own download package with a few clicks.
In doing so you can select:
● Product images, 2D dimension drawings, 3D models, internal circuit diagrams, EPLAN
macro files
● Manuals, characteristics, operating manuals, certificates
● Product master data
You can find "mySupport" - CAx Data in the Internet
(https://support.industry.siemens.com/my/ww/en/CAxOnline).
Application examples
The application examples support you with various tools and examples for solving your
automation tasks. Solutions are shown in interplay with multiple components in the system -
separated from the focus in individual products.
You can find the application examples on the Internet
(https://support.industry.siemens.com/sc/ww/en/sc/2054).

Manual, 02/2019, A5E03574575-AF 7
Documentation guide
TIA Selection Tool

With the TIA Selection Tool, you can select, configure and order devices for Totally
Integrated Automation (TIA).
This tool is the successor of the SIMATIC Selection Tool and combines the known
configurators for automation technology into one tool.
With the TIA Selection Tool, you can generate a complete order list from your product
selection or product configuration.
You can find the TIA Selection Tool on the Internet
(https://w3.siemens.com/mcms/topics/en/simatic/tia-selection-tool).
SIMATIC Automation Tool

You can use the SIMATIC Automation Tool to run commissioning and maintenance activities
simultaneously on various SIMATIC S7 stations as a bulk operation independently of the TIA
Portal.
The SIMATIC Automation Tool provides a multitude of functions:
● Scanning of a PROFINET/Ethernet network and identification of all connected CPUs
● Address assignment (IP, subnet, gateway) and station name (PROFINET device) to a
CPU
● Transfer of the data and the programming device/PC time converted to UTC time to the
module
● Program download to CPU
● Operating mode switchover RUN/STOP
● Localization of the CPU by means of LED flashing
● Reading out CPU error information
● Reading the CPU diagnostic buffer
● Reset to factory settings
● Updating the firmware of the CPU and connected modules
You can find the SIMATIC Automation Tool on the Internet
PRONETA
With SIEMENS PRONETA (PROFINET network analysis), you analyze the plant network
during commissioning. PRONETA features two core functions:
● The topology overview independently scans PROFINET and all connected components.
● The IO check is a fast test of the wiring and the module configuration of a system.
You can find SIEMENS PRONETA on the Internet

8 Manual, 02/2019, A5E03574575-AF
Documentation guide
SINETPLAN
SINETPLAN, the Siemens Network Planner, supports you in planning automation systems
and networks based on PROFINET. The tool facilitates professional and predictive
dimensioning of your PROFINET installation as early as in the planning stage. In addition,
SINETPLAN supports you during network optimization and helps you to exploit network
resources optimally and to plan reserves. This helps to prevent problems in commissioning
or failures during productive operation even in advance of a planned operation. This
increases the availability of the production plant and helps improve operational safety.
The advantages at a glance
● Network optimization thanks to port-specific calculation of the network load
● Increased production availability thanks to online scan and verification of existing systems
● Transparency before commissioning through importing and simulation of existing STEP 7
projects
● Efficiency through securing existing investments in the long term and optimal exploitation
of resources
You can find SINETPLAN on the Internet (https://www.siemens.com/sinetplan).

Manual, 02/2019, A5E03574575-AF 9
Product overview 2
2.1 Properties
Article number
6ES7132-6BF01-0BA0 (number in package unit: 1 unit)
6ES7132-6BF01-2BA0 (number in package unit: 10 units)
View of the module
① Module type and name ⑦ Function class

② LED for diagnostics ⑧ Color coding module type
③ 2D matrix code ⑨ Function and firmware version
④ Wiring diagram ⑩ Color code for selecting the color identification labels
⑤ LEDs for channel status ⑪ BU type
⑥ LED for supply voltage ⑫ Article number
Figure 2-1 View of the module DQ 8×24VDC/0.5A ST

10 Manual, 02/2019, A5E03574575-AF
Product overview
2.1 Properties
Properties
The module has the following technical properties:
● Digital output module with 8 outputs
● Supply voltage L+
● Output current 0.5 A per channel
● Source output (PNP)
● Configurable diagnostics (per module)
● Configurable substitute values (per channel)
● Suitable for solenoid valves, DC contactors, and indicator lights
● Safety-related shutdown
The module supports the following functions:
Table 2- 1 Version dependencies of the functions
HW ver- FW STEP 7 GSD file

Function sion version TIA Portal V5.x PROFINET IO PROFIBUS DP
Identification data FS01 V0.0.0 V14 or higher V5.5 SP3 or higher X X
I&M0 to I&M3 and with HSP 0222 with HSP 0230 V7.0
higher
Configuration in RUN FS01 V0.0.0 V14 or higher V5.5 SP3 or higher X X
and with HSP 0222 with HSP 0230 V7.0
higher
PROFIenergy FS01 V0.0.0 V14 or higher V5.5 SP3 or higher X X
higher
Value status FS01 V0.0.0 V14 or higher V5.5 SP3 or higher X X
higher
Accessories
The following accessories must be ordered separately:
● Labeling strips
● Color identification labels
● Reference identification label
● Shield connector
See also
You can find additional information on the accessories in the ET 200SP distributed I/O
system (http://support.automation.siemens.com/WW/view/en/58649293) system manual.

Manual, 02/2019, A5E03574575-AF 11
Wiring up 3
3.1 Wiring and block diagram
This section includes the block diagram of the DQ 8x24VDC/0.5A ST module with the
terminal assignments for a 1-wire, 2-wire and 3-wire connection.
You can use and combine the different wiring options for all channels.
You can find information on wiring the BaseUnit in the system manual Distributed I/O System
ET 200SP (http://support.automation.siemens.com/WW/view/en/58649293).
Note
The load group of the module must begin with a light-colored BaseUnit. Keep this in mind
also during the configuration.
Note
Cross circuit at output
Be aware that voltage from a cross-circuit at the output can feed L+ to modules.

12 Manual, 02/2019, A5E03574575-AF
Wiring up
Wiring: 1 and 2-wire connection of actuators

The following figure shows an example of the terminal assignment of the digital output
module DQ 8×24VDC/0.5A ST on the BaseUnit BU type A0 without AUX terminals (1-wire
and 2-wire connection).
① 1-wire connection 24 V DC Supply voltage L+ (infeed for light-colored BaseUnit

only)
② 2-wire connection M Ground
③ Backplane bus interface P1, P2, AUX Internal self-assembling voltage buses
Connection to left (dark-colored BaseUnit)
Connection to left interrupted (light-colored Ba-
seUnit)
④ Output electronics DQn Output signal, channel n
⑤ Polarity reversal protection DIAG Error or diagnostics LED (green, red)
⑥ Color-coded label with color code CC02 (op- .0 to .7 Channel status LED (green)
tional)
⑦ Filter connection supply voltage (only when PWR Power LED (green)
light-colored BaseUnit is present)

Manual, 02/2019, A5E03574575-AF 13
Wiring up
Figure 3-1 Block diagram and terminal assignment for 1- and 2-wire connection of actuators
Wiring: 3-wire connection of actuators

The following figure shows an example of the terminal assignment of the digital output
module DQ 8×24VDC/0.5A ST on the BaseUnit BU type A0 with AUX terminals (3-wire
connection).
① 3-wire connection 1 A to 10 A AUX terminals

② Color-coded labels with color codes CC02 and PE (AUX) Protective conductor connection
CC71 (optional)
③ Filter connection supply voltage (only when 24 V DC Supply voltage L+ (infeed for light-colored Ba-
light-colored BaseUnit is present) seUnit only)
DQn Output signal, channel n M Ground
P1, P2, AUX Internal self-assembling voltage buses
Connection to left (dark-colored BaseUnit)
Connection to left interrupted (light-colored
BaseUnit)
Figure 3-2 Terminal assignment for 3-wire connection of actuators

14 Manual, 02/2019, A5E03574575-AF
Parameters/address space 4
4.1 Parameters
Parameters for DQ 8x24VDC/0.5A ST

Specify the module properties with the various parameters in the course of your STEP 7
configuration. The following table lists the configurable parameters. The effective range of
the parameters depends on the type of configuration.
The following configurations are possible:
● Central operation with an ET 200SP CPU
● Distributed operation on PROFINET IO in an ET 200SP system
● Distributed operation with PROFIBUS DP in an ET 200SP system
When assigning parameters in the user program, use the "WRREC" instruction to transfer
the parameters to the module by means of data records, see section Parameter assignment
and structure of parameter data record (Page 28).
The following parameter settings are possible:
Table 4- 1 Settable parameters and their defaults (GSD file)
Parameters Value range Default Configura- Scope with configuration software,

tion in RUN e.g. STEP 7 (TIA Portal)
GSD file GSD file
PROFINET IO PROFIBUS DP 1
Diagnostics • Disable Disable yes Module Module
No supply voltage L+
• Enable
Short-circuit to ground
• Enable
Short-circuit to L+
• Enable
Wire break
• Enable
Channel activated • Disable Enable yes Channel Channel
• Enable

Manual, 02/2019, A5E03574575-AF 15
4.1 Parameters
Parameters Value range Default Configura- Scope with configuration software,

tion in RUN e.g. STEP 7 (TIA Portal)
GSD file GSD file
PROFINET IO PROFIBUS DP 1
Reaction to CPU • Turn off Turn off yes Channel Module
STOP
• Keep last value
• Output substitute value 1
Potential group • Use potential group of the Use potential no Module Module
left module (module group of the
plugged into a dark- left module
colored BaseUnit)
• Enable new potential
group (module plugged in-
to light-colored BaseUnit)
1 Due to the limited number of parameters of a maximum of 244 bytes per ET 200SP station with a PROFIBUS GSD
configuration, the parameter assignment options are restricted. The parameter length of the I/O module is 4 bytes with
PROFIBUS GSD configuration. If necessary, you can set this parameter by using the data record 128, see the appendix
"Parameter data record".
Note
If both parameters "Diagnostics: short-circuit to L+" and "Diagnostics: wire break" are
enabled and one of these diagnostic events occurs, the affected channel is switched off to
avoid triggering an undefined load and the corresponding diagnostic alarm.
If both parameters "Diagnostics: short-circuit to L+" and "Diagnostics: wire break" are
enabled and one of these diagnostic events occurs, the affected channel is switched off to
avoid triggering an undefined load and the corresponding diagnostic alarm.
If the parameter "Diagnostics: short-circuit to L+" is enabled and "Diagnostics: wire break" is
disabled, the signal status is retained at the affected channel when "Diagnostics: short-circuit
to L+" occurs. A diagnostic alarm is triggered only for 0 signal.

16 Manual, 02/2019, A5E03574575-AF
4.2 Explanation of the parameters
4.2 Explanation of the parameters
Diagnostics no supply voltage L+

Enabling of the diagnostics for no or insufficient supply voltage L+.
Diagnostics short-circuit to ground

Enabling of the diagnostics if a short-circuit of the actuator supply to ground occurs.
Diagnostics short-circuit to L+
Enabling of the diagnostics if a short-circuit of the actuator supply to L+ occurs.
Diagnostics wire break

Enabling of the diagnostics if the line to the actuator is broken.
The module responds to a wire break as follows:
● Disabled
– Channel status LED lit green.
– Output voltage present at channel.
● Enabled
– Channel status LED is off.
– Output is switched off.
– In addition, the "Diagnostics: Wire break" is signaled and the DIAG LED on the module
flashes.
Note
If one of the two parameters "Diagnostics: Short-circuit to L+" or "Diagnostics: Wire break" is
enabled and one of these diagnostics occurs, the affected channel is switched off. This
prevents undefined load switching and supports detection of a faulty channel for module
diagnostics.
Channel activated
Determines whether a channel is enabled or disabled.
Reaction to CPU STOP

Specifies the behavior of the module if the CPU changes to STOP.

Manual, 02/2019, A5E03574575-AF 17
4.3 Address space
Potential group
A potential group consists of a group of directly adjacent I/O modules within an ET 200SP
station, which are supplied via a common supply voltage.
A potential group begins with a light-colored BaseUnit through which the required voltage is
supplied for all modules of the potential group. The light-colored BaseUnit interrupts the
three self-assembling voltage buses P1, P2 and AUX to the left neighbor.
All additional I/O modules of this potential group are plugged into dark-colored BaseUnits.
You take the potential of the self-assembling voltage buses P1, P2 and AUX from the left
neighbor.
A potential group ends with the dark-colored BaseUnit, which follows a light-colored
BaseUnit or server module in the station configuration.
4.3 Address space

The module can be configured differently in STEP 7; see following table. Depending on the
configuration, additional/different addresses are assigned in the process image of the inputs.
Configuration options of DQ 8x24VDC 0.5A ST

You can configure the module with STEP 7 (TIA Portal) or with a GSD file. If you configure
the module using a GSD file, the configurations are available under various short
designations/module names; see the table below. The following configurations are possible:
Table 4- 2 Configuration options with GSD file
Configuration Short designation/module Configuration software, e.g. with STEP 7 (TIA Portal)
name in the GSD file Integrated in hardware GSD file GSD file
catalog STEP 7 PROFINET IO PROFIBUS DP
1 x 8-channel without value DQ 8x24VDC 0.5A ST V14, SP1 or higher with X X
status V0.0 HSP 0222
1 x 8-channel with value DQ 8x24VDC 0.5A ST V14, SP1 or higher with X ---
status V0.0, QI HSP 0222
Evaluating the value status

An additional byte is allocated in the input address space if you enable the value status for
the digital module. Bits 0 to 7 in this byte are assigned to a channel. They provide
information about the validity of the digital value.
Bit = 1: No fault is present on the channel.
Bit = 0: Channel is disabled or there is a fault/error on the module.
If a fault/error occurs on a channel with this module, the value status for all channels is 0.

18 Manual, 02/2019, A5E03574575-AF
4.3 Address space
Address space
The following figure shows the assignment of the address space for the
DQ 8×24VDC/0.5A ST with value status (Quality Information (QI)). The addresses for the
value status are only available if the value status is enabled.
Figure 4-1 Address space of the DQ 8×24VDC/0.5A ST with value status

Manual, 02/2019, A5E03574575-AF 19
Interrupts/diagnostics alarms 5
5.1 Status and error display
LED display
DQ 8x24VDC/0.5A ST.
① DIAG (green/red)
② Channel status (green)
③ PWR (green)
Figure 5-1 LED display

20 Manual, 02/2019, A5E03574575-AF
5.1 Status and error display
Meaning of the LED displays

The following tables show the meaning of the status and error displays. Measures for dealing
with diagnostics alarms can be found in the section Diagnostics alarms (Page 22).
DIAG LED
Table 5- 1 DIAG LED fault/error display
DIAG LED Meaning

Backplane bus supply of the ET 200SP not OK
off
Module parameters not assigned
Flashes
Module parameters assigned
on
Module diagnostics is available
Flashes
Channel status LED
Table 5- 2 Status display of the channel status LED
Channel status Meaning

LED
Channel deactivated or activated and process signal = 0
off
Channel activated and process signal = 1
on
PWR LED
Table 5- 3 Status display of the PWR LED
PWR LED Meaning

No supply voltage L+
off
Supply voltage L+ present
on

Manual, 02/2019, A5E03574575-AF 21
5.2 Interrupts
5.2 Interrupts
The digital output module DQ 8x24...24VDC/0.5A ST supports diagnostic interrupts.
Diagnostics interrupt
The module generates a diagnostics interrupt for the following events:
● Short-circuit
● Wire break
● Parameter assignment error
● No supply voltage
5.3 Diagnostics alarms

A diagnostic alarm is generated and the DIAG-LED flashes on the module for each
diagnostics event. You can read out the diagnostics alarms, for example, in the diagnostics
buffer of the CPU. You can evaluate the error codes with the user program.
Table 5- 4 Diagnostics alarms, their meaning and how to deal with them
Diagnostics alarm Error code Meaning Remedy

Short-circuit 1H • Short-circuit of actuator supply to Correct the process wiring
ground
• Short-circuit of actuator supply to L+
Wire break 6H Actuator circuit impedance too high. Use a different actuator type or wire
differently, e.g. use cables with a larger
cross-section
Wire break between the module and actu- Connect the cable
ator
Channel not connected (open) • Disable diagnostics
• Connect a resistor to the actuator
contacts in the load resistance range
Parameter assign- 10H • The module cannot evaluate parame- Correct the parameter assignment
ment error ters for the channel.
• Incorrect parameter assignment.
No supply voltage 11H No or insufficient supply voltage L+ • Check supply voltage L+ on the Ba-
seUnit
• Check BaseUnit type

22 Manual, 02/2019, A5E03574575-AF
Technical specifications 6
6.1 Technical specifications
Technical specifications of the DQ 8x24VDC/0.5A ST

The following table shows the technical specifications as of 02/2019. You will find a data
sheet including daily updated technical specifications on the Internet
(https://support.industry.siemens.com/cs/ww/en/pv/6ES7132-6BF01-0BA0/td?dl=en).
Article number 6ES7132-6BF01-0BA0

General information
Product type designation DQ 8x24VDC/0.5A ST
HW functional status From FS02
Firmware version V0.0
• FW update possible No
usable BaseUnits BU type A0

Color code for module-specific color identifica- CC02
tion plate
Product function
• I&M data Yes; I&M0 to I&M3
Engineering with
• STEP 7 TIA Portal configurable/integrated V14
as of version
• STEP 7 configurable/integrated as of ver- V5.5 SP3 or higher

sion
• PCS 7 configurable/integrated as of version V8.1 SP1
• PROFIBUS as of GSD version/GSD revi- One GSD file each, Revision 3 and 5 and higher
sion
• PROFINET as of GSD version/GSD revi- GSDML V2.3

sion
Operating mode
• DQ Yes
• DQ with energy-saving function No
• PWM No
• Oversampling No
• MSO No
Redundancy
• Redundancy capability Yes

Manual, 02/2019, A5E03574575-AF 23

Supply voltage
Rated value (DC) 24 V
permissible range, lower limit (DC) 19.2 V
permissible range, upper limit (DC) 28.8 V
Reverse polarity protection Yes
Input current
Current consumption, max. 35 mA; without load
Output voltage
Rated value (DC) 24 V
Power loss
Power loss, typ. 1W
Address area
Address space per module
• Address space per module, max. 1 byte; + 1 byte for QI information
Hardware configuration
Automatic encoding Yes
• Mechanical coding element Yes
Selection of BaseUnit for connection variants

• 1-wire connection BU type A0
• 2-wire connection BU type A0
• 3-wire connection BU type A0 with AUX terminals or potential dis-

tributor module
• 4-wire connection BU type A0 + Potential isolation module
Digital outputs
Type of digital output Source output (PNP, current-sourcing)
Number of digital outputs 8
Current-sourcing Yes
Digital outputs, parameterizable Yes
Short-circuit protection Yes
• Response threshold, typ. 1A
Limitation of inductive shutdown voltage to Typ. L+ (-50 V)

Controlling a digital input Yes
Switching capacity of the outputs
• with resistive load, max. 0.5 A
• on lamp load, max. 5W
Load resistance range

• lower limit 48 Ω
• upper limit 12 kΩ
Output voltage
• for signal "1", min. L+ (-0.8 V)

24 Manual, 02/2019, A5E03574575-AF

Output current
• for signal "1" rated value 0.5 A
• for signal "1" permissible range, max. 0.5 A
• for signal "0" residual current, max. 0.1 mA
Output delay with resistive load

• "0" to "1", max. 50 µs; at rated load
• "1" to "0", max. 100 µs; at rated load
Parallel switching of two outputs

• for uprating No
• for redundant control of a load Yes
Switching frequency
• with resistive load, max. 100 Hz
• with inductive load, max. 2 Hz
• on lamp load, max. 10 Hz
Total current of the outputs

• Current per channel, max. 0.5 A
• Current per module, max. 4A
Total current of the outputs (per module)

horizontal installation
– up to 30 °C, max. 4A
vertical installation
Cable length
• shielded, max. 1 000 m
• unshielded, max. 600 m
Isochronous mode
Isochronous operation (application synchro- No
nized up to terminal)
Interrupts/diagnostics/status information
Diagnostics function Yes
Substitute values connectable Yes
Alarms
• Diagnostic alarm Yes

Manual, 02/2019, A5E03574575-AF 25

Diagnostic messages
• Monitoring the supply voltage Yes
• Wire-break Yes; Module-wise
• Short-circuit to M Yes; Module-wise
• Short-circuit to L+ Yes; Module-wise
• Group error Yes
Diagnostics indication LED

• Monitoring of the supply voltage (PWR- Yes; green PWR LED
LED)
• Channel status display Yes; Green LED
• for channel diagnostics No
• for module diagnostics Yes; green/red DIAG LED
Potential separation
Potential separation channels
• between the channels No
• between the channels and backplane bus Yes
• between the channels and the power sup- No

ply of the electronics
Isolation
Isolation tested with 707 V DC (type test)
Standards, approvals, certificates
Suitable for safety functions No
Suitable for safety-related tripping of standard Yes; From FS01
modules
Highest safety class achievable in safety mode
• Performance level according to ISO 13849- PL d
1
• SIL acc. to IEC 61508 SIL 2
Ambient conditions
Ambient temperature during operation
• horizontal installation, min. -30 °C
• horizontal installation, max. 60 °C
• vertical installation, min. -30 °C
• vertical installation, max. 50 °C
Altitude during operation relating to sea level

• Installation altitude above sea level, max. 2 000 m; On request: Installation altitudes greater
than 2 000 m

26 Manual, 02/2019, A5E03574575-AF

Dimensions
Width 15 mm
Height 73 mm
Depth 58 mm
Weights
Weight, approx. 30 g
Safety-related shutdown
Note
The digital output module DQ 8x24VDC/0.5A ST supports safety-related shutdown in
connection with a fail-safe power module F-PM-E 24VDC/8A PPM ST:
• SIL according to IEC 61508: 2
• Highest attainable safety class in safety mode, performance level according to
EN ISO 13849-1: d
Residual current for signal state "0"
Note
Residual current for signal state "0"
Due to the Diagnostics: Wire break function, there is a low level of residual current in the "0"
signal state at the output, which may cause the display diodes to flicker.
This residual current does not depend on the setting for the Diagnostics: Wire break
parameter.
Dimension drawing
See manual ET 200SP BaseUnits
(http://support.automation.siemens.com/WW/view/en/58532597/133300)

Manual, 02/2019, A5E03574575-AF 27
Parameter data record A
A.1 Parameter assignment and structure of the parameter data record
The data record of the module has an identical structure, regardless of whether you
configure the module with PROFIBUS DP or PROFINET IO. With data record 128, you can
reconfigure the module in your user program regardless of your programming. This means
that you can use all the functions of the module even if you configured it via PROFIBUS-
GSD.
Parameter assignment in the user program

You have the option to reconfigure the module in RUN (e.g. the response of selected
channels to the CPU-STOP state can be changed in RUN without having an effect on the
other channels).
Changing parameters in RUN

The "WRREC" instruction is used to transfer the parameters to the module using data
record 128. The parameters set in STEP 7 are not changed in the CPU, which means that
the parameters set in STEP 7 will be valid again after a restart.
Output parameter STATUS

If errors occur when transferring parameters with the "WRREC" instruction, the module
continues operation with the previous parameter assignment. The STATUS output
parameter contains a corresponding error code.
You will find a description of the "WRREC" instruction and the error codes in the STEP 7
online help.

28 Manual, 02/2019, A5E03574575-AF
Structure of data record 128
Note
Channel 0 contains the diagnostics for the entire module.
Figure A-1 Structure of data record 128
Header information
The figure below shows the structure of the header information.
Figure A-2 Header information

Manual, 02/2019, A5E03574575-AF 29
Parameters
The figure below shows the structure of the parameters for channels 0 to 7.
You enable a parameter by setting the corresponding bit to "1".
Figure A-3 Structure byte x to x+1 for the channels 0 to 7

30 Manual, 02/2019, A5E03574575-AF
Error transferring the data record

The module always checks all the values of the transferred data record. Only if all the values
were transferred without errors does the module apply the values from the data record.
The WRREC instruction for writing data records returns corresponding error codes when
errors occur in the STATUS parameter. (See also the description of the "STATUS"
parameter in the STEP 7 online help).
The following table shows the module-specific error codes and their meaning for the
parameter data record 128.
Error code in STATUS parameter Meaning Solution

(hexadecimal)
Byte 0 Byte 1 Byte 2 Byte 3
DF 80 B0 xx Number of the data record un- Enter a valid number for the data record.
known.
DF 80 B1 xx Length of the data record incorrect. Enter a valid value for the data record length.
DF 80 B2 xx Slot invalid or cannot be accessed. • Check the station whether the module is
plugged or drawn.
• Check the assigned values for the pa-
rameters of the WRREC instruction.
DF 80 E0 xx Wrong version or error in the Correct the version, length and number of
header information. parameter blocks.
DF 80 E1 06 Invalid coding for substitute value Check the parameters of the module.
behavior.

Manual, 02/2019, A5E03574575-AF 31

Et200sp DQ 8x24vdc 0 5a ST Manual en-US en-US

Uploaded by

Copyright:

Available Formats

Et200sp DQ 8x24vdc 0 5a ST Manual en-US en-US

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Et200sp DQ 8x24vdc 0 5a ST Manual en-US en-US

Uploaded by

Copyright:

Available Formats

Preface

Digital output module 4

Siemens AG A5E03574575-AF Copyright © Siemens AG 2012 - 2019.

Purpose of the documentation

Changes compared to previous version

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Manual Collection ET 200SP

"mySupport" - CAx Data

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

TIA Selection Tool

SIMATIC Automation Tool

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

View of the module

① Module type and name ⑦ Function class

Figure 2-1 View of the module DQ 8×24VDC/0.5A ST

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Table 2- 1 Version dependencies of the functions

HW ver- FW STEP 7 GSD file

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Wiring: 1 and 2-wire connection of actuators

① 1-wire connection 24 V DC Supply voltage L+ (infeed for light-colored BaseUnit

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Wiring: 3-wire connection of actuators

① 3-wire connection 1 A to 10 A AUX terminals

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Parameters for DQ 8x24VDC/0.5A ST

Table 4- 1 Settable parameters and their defaults (GSD file)

Parameters Value range Default Configura- Scope with configuration software,

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Parameters Value range Default Configura- Scope with configuration software,

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

4.2 Explanation of the parameters

Diagnostics no supply voltage L+

Diagnostics short-circuit to ground

Diagnostics wire break

Reaction to CPU STOP

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

4.3 Address space

Configuration options of DQ 8x24VDC 0.5A ST

Table 4- 2 Configuration options with GSD file

Evaluating the value status

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Figure 4-1 Address space of the DQ 8×24VDC/0.5A ST with value status

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Figure 5-1 LED display

Digital output module DQ 8x24VDC/0.5A ST (6ES7132-6BF01-0BA0)

Meaning of the LED displays

Table 5- 1 DIAG LED fault/error display

DIAG LED Meaning

Channel status LED

Table 5- 2 Status display of the channel status LED

Channel status Meaning

Table 5- 3 Status display of the PWR LED

PWR LED Meaning