Maxim Silencer Catalog
Maxim Silencer Catalog
Maxim Silencer Catalog
com
Maxim Silencers products are warranted for one year from date of purchase by the consumer against defects due to materials
and workmanship only. In case of a defective product, Maxim Silencers shall be the sole judge in determining the nature
of the defect. Maxim Silencers sole obligation shall be to repair, or at Maxim Silencers option, to replace said products
providing the originals are returned to Maxim Silencers. All returned items must be pre-approved by Maxim Silencers. All
return shipments must be prepaid by the consumer. Defects or failures due to improper or careless installation, storage,
handling, or application shall be excluded from this warranty. Failure to comply or contrary usage to Maxim Silencers
directions, specifications or design, of which Maxim Silencers shall be sole judge, voids this warranty and all said products
are specifically excluded from this warranty. No liability for damage or loss of any nature arising from or out of the use of this
product, whether or not defective, is assumed. No liability is accepted for return transportation charges, following the repair
or replacement, as previously mentioned, or for reinstallation costs. No other expressed or implied warranties exist in the
absence of special written agreement between the consumer and Maxim Silencers.
The attenuation curves outlined in the Maxim catalogs represent the dynamic insertion loss at each frequency using the
respective size silencer as indicated in the curves. Actual silenced noise levels may vary due to several factors such as
engine, speed, loading, unsilenced noise, temperature and environmental conditions. The Maxim curves in the sales literature
represent the outlet dynamic insertion loss for noise only and does not include any structural, vibration, and/or flanking noise
that may occur. The attenuation curves should be used as a guideline only due to countless variations.
2
www.MaximSilencers.com (832) 554-0980
Revision: M-ESCS-003
TABLE OF CONTENTS
Maxim Silencers Exhaust Silencer Catalog
3
www.MaximSilencers.com (832) 554-0980 Guides
Revision: M-ESCS-003
Guides - Nomenclature
Drawing Number
standard location
MT Series T Stainless Steel 316 3 End in, Side out D3 “D” Legs (3) X On Inlet and Outlet
L Stainless Steel 316L 4 Side in, Side out D4 “D” Legs (4)
Size
Drawing Number
MDSA Series S Stainless Steel 304 2 Side in, Side out F Flush Mount T Top
MR Series T Stainless Steel 316 3 End in, End out
Size
Orientation: Orientation and mounting arrangements are viewed horizontally from Left/Inlet to Right/Outlet.
Drawing Numbers: Drawing numbers are usually reserved for customized products. Not all part numbers will have drawing
numbers.
Side Inlet and Outlet Placement: Side inlet and outlet placements are viewed from the inlet end. Other placement options
are available upon request. Mounting placement positions are noted as clock positions.
Side Inlet Manufactured Location: Side inlets are manufactured at the minimum/standard location ("N Min" dimension, see
specs), but can be manufactured within noted min max range at no additional charge. The "N" dimension should be noted and
added to nomenclature at time of order if other than the minimum/standard location. If location falls outside of Min Max range
customizations may be possible, call for details and pricing.
Mounting Direction: Silencers may be mounted vertically or horizontally with the drain located accordingly. Specify prior to
ordering if silencer is to be mounted vertically.
Guides - Nomenclature
Type 1 - SIEO - Side In, End Out Type 2 - SISO - Side In, Side Out Type 3 - EIEO - End In, End Out
Type 4 - Dual SIEO - Dual Side In, End Out Type 5 - Dual SISO - Dual Side In, Side Out Type 6 - Dual EIEO - Dual End In, End Out
Orientation: Orientation and mounting arrangements are viewed horizontally from Left/Inlet to Right/Outlet.
5
www.MaximSilencers.com (832) 554-0980 Guides
Revision: M-ESCS-003
Guides - Nomenclature
Mounting Supports
Horizontal Support Options Vertical Support Options
ES Type “E”
Bracket Support (4)
Mounting Direction: Silencers may be mounted vertically or horizontally with the drain located accordingly. Specify prior to
ordering if silencer is to be mounted vertically.
End In, Side Out at 3 o'clock Side In 3 o'clock, Side Out 12 o'clock Side in 6 o'clock, Side Out 9 o'clock
Side Inlet and Outlet Placement: Side inlet and outlet placements are viewed from the inlet end. Other placement options
are available upon request. Mounting placement positions are noted as clock positions.
6
www.MaximSilencers.com (832) 554-0980 M11
Revision: M-ESCS-003
• Drain connection 10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
M11
Part No.* Size / ØC ØA B N Min N Max O P R Min R Max S H Est Wt
M11-1.5 1.5 6 20 3 6 17 3 14 3 10
M11-2 2 6 20 3.5 6 17 3.5 14 3 11
M11-2.5 2.5 7 20 4 6.5 17 4 14 3 15
M11-3 3 8 24 4 7 21 4 18 3 20
-Consult Factory-
-Consult Factory-
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
M22
Part No.* Size / ØC ØA B N Min N Max O P R Min R Max S H Est Wt
M22-4 4 14 36 6 11 11 32 6 28 4 60
M22-5 5 16 43 7 15 12 39 7 35 4 80
M22-6 6 18 49 7.5 18 13 45 7.5 41 4 102
M22-8 8 22 59 9.5 23 15 55 9.5 51 4 170
M22-10 10 26 64 11.5 26 17 60 11.5 56 4 270
-Consult Factory-
M22-12 12 30 77 13 32 19 73 13 69 4 415
M22-14 14 36 83 15.5 34 23 78 15.5 73 5 550
M22-16 16 40 90 16.5 36 25 85 16.5 80 5 784
M22-18 18 45 96 18 39 27.5 91 18 86 5 931
M22-20 20 50 109 20.5 47 30 104 20.5 99 5 1357
M22-22 22 54 119 22.5 50 32 114 22.5 109 5 1764
M22-24 24 60 125 24 56 35 120 24 115 5 2105
M22-26 26 64 140 25.5 61 37 135 25.5 13 5 2477
M22-28 28 68 155 26.5 69 39 150 26.5 145 5 2856
M22-30 30 72 166 28 75 41 161 28 156 5 3259
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
8
www.MaximSilencers.com (832) 554-0980 M32
Revision: M-ESCS-003
50
• Advanced acoustical design
• Drain connection 0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
M32
Part No.* Size / ØC ØA B N Min N Max O P R Min R Max S H Est Wt
M32-1 1 6 20 3 5 6 17 3 14 3 10
M32-1.5 1.5 9 30 4 11 7.5 27 4 24 3 23
M32-2 2 9 30 4.5 11 7.5 27 4.5 24 3 24
M32-2.5 2.5 10 34 5 12 8 31 5 28 3 33
M32-3 3 12 38 5.5 15 9 35 5.5 32 3 50
M32-3.5 3.5 14 42 6 16 10 39 6 36 3 65
M32-4 4 14 48 6 17 11 44 6 40 4 75
M32-5 5 16 57 7 23 12 53 7 49 4 100
-Consult Factory-
M32-6 6 18 63 8 25 13 59 8 55 4 126
M32-8 8 22 74 9.5 32 15 70 9.5 66 4 203
M32-10 10 26 87 11.5 39 17 83 11.5 79 4 352
M32-12 12 30 102 13 45 19 98 13 94 4 519
M32-14 14 36 109 15.5 46 23 104 15.5 99 5 674
M32-16 16 40 119 16.5 51 25 114 16.5 109 5 973
M32-18 18 45 127 18 56 27.5 122 18 117 5 1165
M32-20 20 50 137 20.5 61 30 132 20.5 127 5 1656
M32-22 22 54 149 22.5 67 32 144 22.5 139 5 2107
M32-24 24 60 162 24 74 35 157 24 152 5 2566
M32-26 26 64 183 25.5 85 37 178 25.5 173 5 3031
M32-28 28 68 200 26.5 93 39 195 26.5 190 5 3468
M32-30 30 72 216 28 102 41 211 28 206 5 3992
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
9
www.MaximSilencers.com (832) 554-0980 M42
Revision: M-ESCS-003
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
M62-6 6 26 85 11 38 17 81 11 77 4 376
M62-8 8 30 103 12 26 19 99 12 95 4 548
M62-10 10 36 118 14 32 22 114 14 110 4 844
M62-12 12 36 130 14 36 22 126 14 122 4 870
M62-14 14 40 145 17 37 25 140 17 135 5 1359
M62-16 16 45 156 19 39 27.5 151 19 146 5 1543
M62-18 18 50 171 21 44 30 166 21 161 5 2417
M62-20 20 54 185 22 48 32 180 22 175 5 2818
M62-22 22 60 199 24 51 35 194 24 189 5 3590
M62-24 24 64 212 26 54 37 207 26 202 5 3916
M62-26 26 68 235 27 60 39 230 27 225 5 4770
M62-28 28 72 268 29 71 41 263 29 258 5 5390
M62-30 30 78 278 32 73 44 273 32 268 5 7679
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
12
www.MaximSilencers.com (832) 554-0980 M72
Revision: M-ESCS-003
• Sizes 6 and under are two chambered, 8 and above are three chambers 10
• Drain connection 0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
-Consult Factory-
50
• Advanced acoustical design
-Consult Factory-
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MSA10-6 6 14 41 6.5 11 37 4 75
MSA10-8 8 16 48 8.5 12 44 4 108
MSA10-10 10 18 50 9.5 13 46 4 138
MSA10-12 12 22 60 11.5 15 56 4 203
MSA10-14 14 30 70 13.5 20 65 5 394
MSA10-16 16 36 80 16.5 23 75 5 535
MSA10-18 18 40 90 17.5 25 85 5 858
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
15
www.MaximSilencers.com (832) 554-0980 MSA11
Revision: M-ESCS-003
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MSA11-5 5 16 43 7 12 39 4 88
MSA11-6 6 18 49 7.5 13 45 4 110
MSA11-8 8 22 59 9.5 15 55 4 178
MSA11-10 10 26 64 11.5 17 60 4 280
MSA11-12 12 30 77 13 19 73 4 416
MSA11-14 14 36 83 15.5 23 78 5 558
MSA11-16 16 40 90 16.5 25 85 5 793
MSA11-18 18 45 96 18 27.5 91 5 950
MSA11-20 20 50 109 20.5 30 104 5 1392
MSA11-22 22 54 119 22.5 32 114 5 1806
MSA11-24 24 60 125 24 35 120 5 2187
MSA11-26 26 64 140 25.5 37 135 5 2586
MSA11-28 28 68 155 26.5 39 150 5 2984
MSA11-30 30 72 166 28 41 161 5 3445
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
16
www.MaximSilencers.com (832) 554-0980 MSA22
Revision: M-ESCS-003
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MSA22-5 5 16 57 7 12 53 4 108
MSA22-6 6 18 63 8 13 59 4 132
MSA22-8 8 22 74 9.5 15 70 4 205
MSA22-10 10 26 87 11.5 17 83 4 356
MSA22-12 12 30 102 13 19 98 4 518
MSA22-14 14 36 109 15.5 23 104 5 687
MSA22-16 16 40 119 16.5 25 114 5 976
MSA22-18 18 45 127 18 27.5 122 5 1169
MSA22-20 20 50 137 20.5 30 132 5 1676
MSA22-22 22 54 149 22.5 32 144 5 2127
MSA22-24 24 60 162 24 35 157 5 2627
MSA22-26 26 64 183 25.5 37 178 5 3106
MSA22-28 28 68 200 26.5 39 195 5 3561
MSA22-30 30 72 216 28 41 211 5 4140
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
17
www.MaximSilencers.com (832) 554-0980 MSA33
Revision: M-ESCS-003
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
FEATURES 50
• Heavy duty, all welded construction and long service life 30 8"
• Easily installed in any position 12"
• High heat silicone black finish 20 18"
• Two chambers 50
• Drain connection
Typical Attenuation (dB) 40
30 8"
12"
20 18"
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
Type 1 - EIEO
MT22
Part No.* Size / ØC ØA B H Est Wt
MT22-4 4 14 36 4 64
MT22-5 5 16 43 4 87
MT22-6 6 18 49 4 109
MT22-8 8 22 59 4 181
MT22-10 10 26 64 4 290
MT22-12 12 30 77 4 440
MT22-14 14 36 83 5 593
MT22-16 16 40 90 5 813
MT22-18 18 45 96 5 963
MT22-20 20 50 109 5 1438
MT22-22 22 54 119 5 1845
MT22-24 24 60 125 5 2194
MT22-26 26 64 140 5 2573
MT22-28 28 68 155 5 2966
MT22-30 30 72 166 5 3381
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
21
www.MaximSilencers.com (832) 554-0980 MT32
Revision: M-ESCS-003
30 8"
12"
20 18"
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
Type 1 - EIEO
MT32
Part No.* Size / ØC ØA B H Est Wt
MT32-4 4 14 48 4 80
MT32-5 5 16 57 4 109
MT32-6 6 18 63 4 136
MT32-8 8 22 74 4 217
MT32-10 10 26 87 4 377
MT32-12 12 30 102 4 552
MT32-14 14 36 109 5 731
MT32-16 16 40 119 5 1013
MT32-18 18 45 127 5 1204
MT32-20 20 50 137 5 1754
MT32-22 22 54 149 5 2199
MT32-24 24 60 162 5 2660
MT32-26 26 64 183 5 3135
MT32-28 28 68 200 5 3589
MT32-30 30 72 216 5 4124
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
22
www.MaximSilencers.com (832) 554-0980 MT42
Revision: M-ESCS-003
30 8"
12"
20 18"
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
Type 1 - EIEO
MT42
Part No.* Size / ØC ØA B H Est Wt
MT42-4 4 16 51 4 96
MT42-5 5 18 62 4 129
MT42-6 6 22 69 4 185
MT42-8 8 26 82 4 318
MT42-10 10 30 102 4 509
MT42-12 12 36 112 4 691
MT42-14 14 40 120 5 989
MT42-16 16 45 126 5 1182
MT42-18 18 50 135 5 1663
MT42-20 20 54 149 5 2156
MT42-22 22 60 157 5 2563
MT42-24 24 64 164 5 2911
MT42-26 26 68 184 5 3399
MT42-28 28 72 205 5 3921
MT42-30 30 78 220 5 5437
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
23
www.MaximSilencers.com (832) 554-0980 MT52
Revision: M-ESCS-003
30 8"
12"
20 18"
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
Type 1 - EIEO
MT52
Part No.* Size / ØC ØA B H Est Wt
MT52-4 4 18 62 4 120
MT52-5 5 22 74 4 188
MT52-6 6 26 85 4 308
MT52-8 8 30 103 4 525
MT52-10 10 36 118 4 755
MT52-12 12 36 130 4 835
MT52-14 14 40 145 5 1235
MT52-16 16 45 156 5 1500
MT52-18 18 50 171 5 2151
MT52-20 20 54 185 5 2777
MT52-22 22 60 199 5 3351
MT52-24 24 64 212 5 3811
MT52-26 26 68 235 5 4451
MT52-28 28 72 268 5 5221
MT52-30 30 78 278 5 7051
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
24
www.MaximSilencers.com (832) 554-0980 MD22
Revision: M-ESCS-003
FEATURES
• Heavy duty, welded construction
60
• Unpacked/Non-insulated design
• ANSI drilled 125/150 lb. flanges on inlet and outlet 50
• High-temperature, prime coated black finish
• Lift lugs Typical Attenuation (dB) 40
30 8"
12"
20 18"
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MD22
Part No.* Size / ØC ØA D E F G H I Est Wt
MD22-4 4 22 7 11 7.5 15 4 4 103
MD22-5 5 24 8 12 8 16 4 4 119
MD22-6 6 28 8.5 12.5 8.25 18 4 4 147
MD22-8 8 33 13 17 10.5 20.5 4 4 242
MD22-10 10 41 13 17 10.5 24.5 4 4 329
MD22-12 12 45 17 21 12.5 26.5 4 4 464
MD22-14 14 52 18 22 13 30 4 4 539
MD22-16 16 59 21 25 14.5 33.5 4 4 716
MD22-18 18 65 23 27 15.5 36.5 4 4 825
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• A minimum 3" gap is recommended between the silencer and enclosure roof.
• Low Profile Orientations Available: Side In-End Out, Side In-Side Out, End In-End Out or Dual in options.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
25
www.MaximSilencers.com (832) 554-0980 MD32
Revision: M-ESCS-003
FEATURES
• Heavy duty, welded construction
60
• Low surface temperature design
• ANSI drilled 125/150 lb. flanges on inlet and outlet 50
• High-temperature, prime coated black finish
• 2" thick internal insulation within double wall construction Typical Attenuation (dB) 40
• Lift lugs
30 8"
12"
20 18"
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MD32
Part No.* Size / ØC ØA D E F G H I Est Wt
MD32-4 4 28 9 13 8.5 18 4 4 130
MD32-5 5 29 11 15 9.5 18.5 4 4 150
MD32-6 6 33 12 16 10 20.5 4 4 192
MD32-8 8 45 14 18 11 26.5 4 4 341
MD32-10 10 52 16 20 12 30 4 4 561
MD32-12 12 62 18 22 13 35 4 4 816
MD32-14 14 64 23 28 16.5 37 5 5 950
MD32-16 16 74 25 30 17.5 42 5 5 1388
MD32-18 18 84 27 32 18.5 47 5 5 1856
MD32-20 20 92 28 33 19 51 5 5 2186
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• A minimum 3" gap is recommended between the silencer and enclosure roof.
• Low Profile Orientations Available: Side In-End Out, Side In-Side Out, End In-End Out or Dual in options.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
26
www.MaximSilencers.com (832) 554-0980 MD42
Revision: M-ESCS-003
FEATURES
• Heavy duty, welded construction
60
• Low surface temperature design
• ANSI drilled 125/150 lb. flanges on inlet and outlet 50
• High-temperature, prime coated black finish
• 2" thick internal insulation within double wall construction Typical Attenuation (dB) 40
• Lift lugs
30 8"
12"
20 18"
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MD42
Part No.* Size / ØC ØA D E F G H I Est Wt
MD42-4 4 32 10 14 9 20 4 4 165
MD42-5 5 32 11 15 9.5 20 4 4 174
MD42-6 6 38 12 16 10 23 4 4 238
MD42-8 8 52 14 18 11 30 4 4 518
MD42-10 10 59 16 20 12 33.5 4 4 701
MD42-12 12 70 18 22 13 39 4 4 984
MD42-14 14 70 24 29 17 40 5 5 1104
MD42-16 16 75 28 33 19 42.5 5 5 1518
MD42-18 18 86 30 35 20 48 5 5 2006
MD42-20 20 94 32 37 21 52 5 5 2375
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• A minimum 3" gap is recommended between the silencer and enclosure roof.
• Low Profile Orientations Available: Side In-End Out, Side In-Side Out, End In-End Out or Dual in options.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
27
www.MaximSilencers.com (832) 554-0980 MD52
Revision: M-ESCS-003
FEATURES
• Heavy duty, welded construction
• Low surface temperature design 60
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MD52
Part No.* Size / ØC ØA D E F G H I Est Wt
MD52-4 4 40 12 16 10 24 4 4 259
MD52-5 5 49 14 18 11 28.5 4 4 413
MD52-6 6 58 15 19 11.5 33 4 4 653
MD52-8 8 68 17 21 12.5 38 4 4 906
MD52-10 10 78 20 24 14 43 4 4 1373
MD52-12 12 80 23 27 15.5 44 4 4 1544
MD52-14 14 86 27 32 18.5 48 5 5 1961
MD52-16 16 100 30 33 20 55 5 5 2598
MD52-18 18 112 33 38 21.5 61 5 5 3359
MD52-20 20 120 35 39 22.5 65 5 5 3864
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• A minimum 3" gap is recommended between the silencer and enclosure roof.
• Low Profile Orientations Available: Side In-End Out, Side In-Side Out, End In-End Out or Dual in options.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
28
www.MaximSilencers.com (832) 554-0980 MDSA22
Revision: M-ESCS-003
FEATURES
• Heavy duty, welded construction 60
• Unpacked/Non-insulated design
• Low surface temperature design 50
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MDSA22
Part No.* Size / ØC ØA D E F G H I Est Wt
MDSA22-4 4 22 7 11 7.5 15 4 4 105
MDSA22-5 5 24 8 12 8 16 4 4 121
MDSA22-6 6 28 8.5 12.5 8.25 18 4 4 149
MDSA22-8 8 33 12 16 10 20.5 4 4 239
MDSA22-10 10 41 13 17 10.5 24.5 4 4 335
MDSA22-12 12 45 17 21 12.5 26.5 4 4 475
MDSA22-14 14 52 18 22 13 30 4 4 550
MDSA22-16 16 59 21 23 14.5 33.5 4 4 728
MDSA22-18 18 65 23 27 15.5 36.5 4 4 838
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• A minimum 3" gap is recommended between the silencer and enclosure roof.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
29
www.MaximSilencers.com (832) 554-0980 MDSA32
Revision: M-ESCS-003
FEATURES
• Heavy duty, welded construction
60
• Low surface temperature design
• ANSI drilled 125/150 lb. flanges on inlet and outlet 50
• High-temperature, prime coated black finish
• 2" thick internal insulation within double wall construction Typical Attenuation (dB) 40
• Lift lugs
30 8"
12"
20 18"
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MDSA32
Part No.* Size / ØC ØA D E F G H I Est Wt
MDSA32-4 4 28 9 13 8.5 18 4 4 130
MDSA32-5 5 29 11 15 9.5 18.5 4 4 150
MDSA32-6 6 33 12 16 10 20.5 4 4 192
MDSA32-8 8 45 14 18 11 26.5 4 4 341
MDSA32-10 10 52 16 20 12 30 4 4 561
MDSA32-12 12 62 18 22 13 35 4 4 816
MDSA32-14 14 64 23 28 16.5 37 5 5 950
MDSA32-16 16 74 25 30 17.5 42 5 5 1388
MDSA32-18 18 84 27 32 18.5 47 5 5 1856
MDSA32-20 20 92 28 33 19 51 5 5 2186
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• A minimum 3" gap is recommended between the silencer and enclosure roof.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
30
www.MaximSilencers.com (832) 554-0980 MDSA42
Revision: M-ESCS-003
FEATURES
• Heavy duty, welded construction 60
• Low surface temperature design
• ANSI drilled 125/150 lb. flanges on inlet and outlet 50
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MDSA42
Part No.* Size / ØC ØA D E F G H I Est Wt
MDSA42-4 4 32 10 14 9 20 4 4 165
MDSA42-5 5 32 11 15 9.5 20 4 4 174
MDSA42-6 6 38 12 16 10 23 4 4 238
MDSA42-8 8 52 14 18 11 30 4 4 518
MDSA42-10 10 59 16 20 12 33.5 4 4 701
MDSA42-12 12 70 18 22 13 39 4 4 984
MDSA42-14 14 70 24 29 17 40 5 5 1104
MDSA42-16 16 75 28 33 19 42.5 5 5 1518
MDSA42-18 18 86 30 35 20 48 5 5 2006
MDSA42-20 20 94 32 37 21 52 5 5 2375
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• A minimum 3" gap is recommended between the silencer and enclosure roof.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
31
www.MaximSilencers.com (832) 554-0980 MR32
Revision: M-ESCS-003
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
10
0
31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
40
MP11
Part No.* Size / ØE ØA B C D Est Wt
MP11-4 4 10.75 24 18 3 43
MP11-4.5 4.5 10.75 24 18 3 43
MP11-5 5 12.75 30 24 3 63
MP11-6 6 12.75 30 24 3 65
MP11-8 8 14.5 48 36 6 123
MP11-10 10 16.75 60 48 6 191
MP11-12 12 18.75 72 60 6 225
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
35
www.MaximSilencers.com (832) 554-0980 MP31
Revision: M-ESCS-003
40
MP31
Part No.* Size / ØE ØA B C D Est Wt
MP31-4 4 8.75 30 24 3 39
MP31-4.5 4.5 10.75 36 30 3 61
MP31-5 5 10.75 36 30 3 61
MP31-6 6 12.75 42 36 3 94
MP31-8 8 16.75 60 48 6 143
MP31-10 10 20.25 70 58 6 230
MP31-12 12 24.25 82 70 6 327
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
36
www.MaximSilencers.com (832) 554-0980 MP41
Revision: M-ESCS-003
40
FEATURES 20
• Advanced acoustical design
• Reduces noxious fumes and odors 10
MP41
Part No.* Size / ØE ØA B C D Est Wt
MP41-4 4 10.75 54 48 3 83
MP41-4.5 4.5 12.75 54 48 3 103
MP41-5 5 12.75 54 48 3 103
MP41-6 6 14.75 54 48 3 118
MP41-8 8 18.75 60 48 6 167
MP41-10 10 22.25 70 58 6 235
MP41-12 12 26.25 82 70 6 334
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
37
www.MaximSilencers.com (832) 554-0980 MB11
Revision: M-ESCS-003
FEATURES
• Advanced acoustical design 40
6 0
Silencer 12
Size (inches)
24
Or larger 31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MB11
Part No.* Size / ØC ØA B Est Wt
MB11-1 1 4.625 16 10
MB11-1.5 1.5 4.625 20 15
MB11-2 2 5.75 24 20
MB11-2.5 2.5 5.75 26 25
MB11-3 3 7 30 40
MB11-3.5 3.5 7 34 45
MB11-4 4 10.25 38 90
MB11-5 5 12 42 120
MB11-6 6 12 48 145
MB11-8 8 14 54 200
MB11-10 10 16 67 315
MB11-12 12 18 79 420
MB11-14 14 20 91 670
MB11-16 16 22 103 840
MB11-18 18 30 71 980
MB11-20 20 36 83 1370
MB11-22 22 36 89 1505
MB11-24 24 40 98 1920
MB11-26 26 45 106 2325
MB11-28 28 45 111 2495
MB11-30 30 50 121 2995
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
38
www.MaximSilencers.com (832) 554-0980 MB21
Revision: M-ESCS-003
10
6 0
Silencer 12
Size (inches)
24
Or larger 31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MB21
Part No.* Size / ØC ØA B N Min N Max O P Est Wt
MB21-4 4 14 48 5.5 22 10 45 110
MB21-5 5 16 55 6.5 25 11 52.25 120
MB21-6 6 18 63 7 29.5 12 60.25 170
MB21-8 8 22 76 8.5 36.5 14 73.5 285
MB21-10 10 26 91 10.5 43 16.5 88 460
MB21-12 12 30 109 12 53 18.5 106.25 745
MB21-14 14 36 102 14 48 21.5 99.25 965
MB21-16 16 40 119 17 56 23.5 116.5 1340
MB21-18 18 45 127 19 60 26.5 124 1850
MB21-20 20 50 144 21 69 29 141.25 2175
MB21-22 22 54 161 22 78 31 158.5 2650
MB21-24 24 60 165 24 79 34 162.25 3400
MB21-26 26 64 183 26 89 36 180.5 3850
MB21-28 28 68 200 27 98 38 197.75 4840
MB21-30 30 72 216 29 107 40 213.75 5150
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
39
www.MaximSilencers.com (832) 554-0980 MB31
Revision: M-ESCS-003
10
6 0
Silencer 12
Size (inches)
24
Or larger 31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
MB31
Part No.* Size / ØC ØA B N Min N Max O P Est Wt
MB31-4 4 14 52 8.5 19 23 45 150
MB31-5 5 16 60 10 21.5 26 52.25 195
MB31-6 6 18 69 10 26.5 30 60.25 250
MB31-8 8 22 84 11 33.5 36 73.5 380
MB31-10 10 26 101 13.5 40 43 88 620
MB31-12 12 30 121 15 50 51 106.25 1030
MB31-14 14 36 115 18 44 52 99.25 1230
MB31-16 16 40 135 20 53 59 116.5 1815
MB31-18 18 45 140 25 54 58 124 2750
MB31-20 20 50 159 26 64 59 141.25 3210
MB31-22 22 54 177 29 71 60 154.25 3895
MB31-24 24 60 184 30 73 60 162.25 4330
MB31-26 26 64 204 31 84 60 180.5 5005
MB31-28 28 68 223 33 92 62 197.75 6625
MB31-30 30 72 241 34 102 62 213.75 7315
MB31-32 32 76 250 36.5 102.5 64 220.75 8415
MB31-34 34 82 252 37.5 102.5 64 220.5 8995
MB31-36 36 86 254 37.5 102.5 65 221 9485
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
40
www.MaximSilencers.com (832) 554-0980 FP-FPE
Revision: M-ESCS-003
FEATURES 20
• Advanced acoustical design
• Heavy duty, all welded construction and long service life 10
• Easily installed in any position
0
• Prime coated exterior finish 6
Silencer
• Sizes 1.5 to 3.5 have MNPT connections Size (inches)
12
24
Or larger 31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
FP - FPE
Part No.* ØA FP Part No.* ØA FPE Size / ØC B Est Wt
FP-1.5 4.75 FPE-1.5 4.75 1.5 20 8
FP-2 5 FPE-2 5 2 24 12
FP-2.5 6 FPE-2.5 6 2.5 26 14
FP-3 6.5 FPE-3 6.5 3 30 20
FP-3.5 7 FPE-3.5 7 3.5 34 28
FP-4 10 FPE-4 11 4 38 55
FP-5 11.125 FPE-5 12 5 42 63
FP-6 12.125 FPE-6 13 6 48 80
FP-8 14.125 FPE-8 15 8 54 120
FP-10 16.125 FPE-10 17 10 67 180
FP-12 18.125 FPE-12 19 12 79 290
FP-14 20 FPE-14 20 14 91 330
FP-16 22 FPE-16 22 16 103 440
FP-18 24 FPE-18 24 18 116 570
FP-20 26 FPE-20 26 20 128 700
FP-22 28 FPE-22 28 22 140 820
FP-24 30 FPE-24 30 24 152 1100
FP-26 32 FPE-26 32 26 164 1370
FP-28 34 FPE-28 34 28 176 1560
FP-30 36 FPE-30 36 30 188 1770
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
41
www.MaximSilencers.com (832) 554-0980 FPC-FPCE
Revision: M-ESCS-003
40
FEATURES 20
• Advanced acoustical design
• Heavy duty, all welded construction and long service life 10
FPC - FPCE
Part No.* Part No.* Size / ØC ØA B Est Wt
FPC-14 FPCE-14 14 18 35 200
FPC-16 FPCE-16 16 20 39 240
FPC-18 FPCE-18 18 22 44 300
FPC-20 FPCE-20 20 24 48 360
FPC-22 FPCE-22 22 26 52 430
FPC-24 FPCE-24 24 28 56 590
FPC-26 FPCE-26 26 30.375 60 700
FPC-28 FPCE-28 28 32.5 64 800
FPC-30 FPCE-30 30 35.375 68 900
FPC-32 FPCE-32 32 37 72 1200
FPC-34 FPCE-34 34 39.5 76 1330
FPC-36 FPCE-36 36 42 80 1490
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guidefor additional information on part number creation.
42
www.MaximSilencers.com (832) 554-0980 FPS-FPSE
Revision: M-ESCS-003
40
FEATURES 20
Silencer
• Prime coated exterior finish Size (inches)
12
24
Or larger 31.5 63 125 250 500 1000 2000 4000 8000
Octave Band Center Frequency (Hz)
FPS-FPSE
Part No.* Part No.* Size / ØC ØA B Est Wt
FPS-6 FPSE-6 6 14.625 27 75
FPS-8 FPSE-8 8 18 35 130
FPS-10 FPSE-10 10 20.75 44 190
FPS-12 FPSE-12 12 23.375 51 270
FPS-14 FPSE-14 14 26.375 57 370
FPS-16 FPSE-16 16 29.125 66 490
FPS-18 FPSE-18 18 32.125 71 565
FPS-20 FPSE-20 20 34.875 83 820
FPS-22 FPSE-22 22 37.75 89 1000
FPS-24 FPSE-24 24 40.5 98 1280
FPS-26 FPSE-26 26 43.375 106 1530
FPS-28 FPSE-28 28 46.25 111 1700
FPS-30 FPSE-30 30 49 121 1900
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
43
www.MaximSilencers.com (832) 554-0980 AFS2-AFSE2
Revision: M-ESCS-003
50
Typical Applications: Gas turbine, Internal combustion engine intakes and exhaust,
FEATURES
18"
20
• High heat black paint finish 31.5 63 125 250 500 1000 2000
Octave Band Center Frequency (Hz)
4000 8000
AFS2 - AFSE2
Part No.* Part No.* Size / ØC ØA B N O P Est Wt
AFS2-10 AFSE2-10 10 20 56 12 14 70 310
AFS2-12 AFSE2-12 12 24 60 11 16 71 405
AFS2-14 AFSE2-14 14 26 66 13 17 83 520
AFS2-16 AFSE2-16 16 28 80 14 18 96 650
AFS2-18 AFSE2-18 18 36 91 18 22 109 810
AFS2-20 AFSE2-20 20 36 103 20 22 126 965
AFS2-22 AFSE2-22 22 36 110 18 22 126 1200
AFS2-24 AFSE2-24 24 42 115 24 25 136 1340
AFS2-26 AFSE2-26 26 42 129 22 25 153 1625
AFS2-28 AFSE2-28 28 48 141 26 29 174 2075
AFS2-30 AFSE2-30 30 48 144 26 29 174 2550
AFS2-32 AFSE2-32 32 54 150 call call call 2900
AFS2-34 AFSE2-34 34 54 156 call call call 3500
AFS2-36 AFSE2-36 36 60 164 call call call 3650
AFS2-40 AFSE2-40 40 66 176 call call call 4400
AFS2-42 AFSE2-42 42 66 204 call call call 4700
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
44
www.MaximSilencers.com (832) 554-0980
AFS3-AFSE3
Revision: M-ESCS-003
50
Typical Applications: Gas turbine, Internal combustion engine intakes and exhaust,
30
FEATURES 20
18"
AFS3 - AFSE3
Part No.* Part No.* Size / ØC ØA B N O P Est Wt
AFS3-4 AFSE3-4 4 14 54 6 11 56 105
AFS3-5 AFSE3-5 5 16 56 6 12 62 135
AFS3-6 AFSE3-6 6 16 56 7 12 62 145
AFS3-8 AFSE3-8 8 18 60 8 13 70 200
AFS3-10 AFSE3-10 10 20 68 10 14 77 365
AFS3-12 AFSE3-12 12 24 80 12 16 95 525
AFS3-14 AFSE3-14 14 26 96 14 17 106 665
AFS3-16 AFSE3-16 16 28 104 14 18 115 800
AFS3-18 AFSE3-18 18 36 114 18 22 132 1060
AFS3-20 AFSE3-20 20 36 126 18 22 154 1200
AFS3-22 AFSE3-22 22 36 140 19 23 159 1475
AFS3-24 AFSE3-24 24 42 158 24 24 184 1625
AFS3-26 AFSE3-26 26 42 168 24 25 189 1995
AFS3-28 AFSE3-28 28 48 176 24 29 210 2500
AFS3-30 AFSE3-30 30 48 188 26 29 221 3100
AFS3-32 AFSE3-32 32 54 204 call call call 3625
AFS3-34 AFSE3-34 34 54 216 call call call 4300
AFS3-36 AFSE3-36 36 60 228 call call call 4500
AFS3-40 AFSE3-40 40 66 248 call call call 5300
AFS3-42 AFSE3-42 42 66 258 call call call 5800
• All dimensions are in inches. All weights are in pounds. Weights are approximate.
• Listed sound data is based on typical performance and should not be considered absolute.
• *See nomenclature guide for additional information on part number creation.
45
www.MaximSilencers.com (832) 554-0980
Revision: M-ESCS-003
Maxim Silencers
Standard Terms and Conditions
QUOTATIONS: All quotations are made subject to the following Standard Terms and Conditions, unless otherwise specified within the
body of the formal quotation, in which case that section or paragraph only would be superseded. (In the case of a catalytic silencer,
all Standard Terms and Conditions apply except that the LIMITED WARRANTY provision is superseded by the provisions contained
in the document entitled “LIMITED WARRANTY AS APPLIED TO CATALYTIC SILENCER.”) No deviations from or changes to
these Terms and Conditions will be honored or recognized without prior negotiation and written agreement between the Seller and
Purchaser.
PRICING: All quotations are made for immediate acceptance and are subject to change without notice, unless otherwise noted.
Prices quoted are based on the current costs of material and labor and are subject to escalation. Said escalation shall be determined
by the cost of material to Seller on the date of shipment of said material from Supplier, and the costs of labor during the fabrication
cycle. Prices do not include handling charges, transportation or related costs. Buyer agrees to pay the prices quoted by Seller, and is
responsible for freight and handling charges, special packaging beyond the Sellers’ standard packaging, taxes and duties. Handling,
prepaid freight and special packing costs will be added to the purchase price and invoiced separately.
ORDER ACCEPTANCE, DELIVERY: No order is binding on Seller until accepted and acknowledged in writing by Seller by mail or
electronic communication. All delivery dates are approximate and is the date goods leave Sellers dock. The time period for delivery
begins when all documentation and release required to fill the order are present, and not before clarification of all details. All delivery
promises are subject to prior commitment of shop capacity before the receipt of a firm purchase order by Seller. If shipment is delayed
by Purchaser, payment shall become due when Purchaser is notified that equipment is ready for shipment and equipment will
henceforth be held at Purchaser's risk and expense.
SHIPMENT, RISK OF LOSS: Buyer’s purchase order must specify preferred carrier or goods will ship best way, prepaid and added
to the invoice. Shipment is Free Carrier, FCA Sellers facility or origin of shipment, Incoterms 2010, unless otherwise agreed in
writing. Risk of loss and title to goods shall pass to the Purchaser as soon as goods are deposited with the carrier for shipment.
Buyer assumes both risk of loss and damage to the goods as well as title to the goods on Sellers dock; and Buyer is responsible for
all freight, sales and other taxes, customs duties, insurance costs and other expenses relating to the shipment of goods. Buyer is
responsible for all costs, reporting, and compliance with export control laws related to the goods’ export.
CREDIT and PAYMENT: Credit accounts will be opened only with firms or individuals approved by the Seller's Credit Department.
Purchaser with approved payment terms agrees to pay invoiced amount to Seller on or before thirty (30) days from date of invoice
unless otherwise specified and/or agreed upon in writing. All past due accounts are subject to interest at the rate of one percent (1
%) per month on the unpaid balance. Seller reserves the right at any time upon notice to purchaser, to alter or suspend credit, when
in its sole opinion the financial condition of the Purchaser so warrants. In such cases, cash payment or satisfactory security from the
Purchaser may be required by the Seller before credit is restored or Seller continues performance.
CANCELLATION: Cancellation shall be affected only by a written agreement and Purchaser will assume full liability for payment of
any and all cancellation charges.
RETURNED GOODS: A RMA packing slip must be received and included with any returns. No material will be accepted for
replacement or credit without Seller's written consent and then only under the terms of such consent. Returns for credit will include a
restocking fee, unless otherwise specified and/or agreed upon in writing.
LIMITED WARRANTY: Seller warrants only goods of its own manufacture and then only to the extent that they are free from
defects in material and workmanship under normal use and service for the purpose for which they were manufactured and when
correctly installed and maintained within one (1) year from the date of shipment. This warranty is limited to repair or replacement
of the goods FCA point of manufacture at the Seller's option. Seller does not warrant secondhand material. THESE WARRANTIES
ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING THE
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Purchaser waives any warranties of any kind
whatsoever including but not limited to a waiver of any warranties of fitness, any warranties as to the suitability of the product for its
intended use, and any warranties as to the return of the purchase price. It is further understood and agreed that this is Purchaser's
only remedy for all claims arising or relating to the goods purchased hereunder for breach of contract and tort including negligence
and strict liability and any other legal theory. Seller shall not be responsible for deterioration of any part or parts of the equipment due
to corrosion, erosion or any other causes, regardless of when such deterioration occurs, after leaving the manufacturer's premises.
No allowance will be granted for repairs or alterations made by Purchaser or at Purchaser's direction without Seller's written consent.
Seller shall not be liable for consequential, incidental or any damages other than repair or replacement of defective goods at Seller's
option. It is understood that Seller makes no warranty except as expressly stipulated herein and Seller's liability is limited as above set
forth. NOT WARRANTED: Maxim Silencers offers no paint guarantees other than preparation and application in accordance with
46
www.MaximSilencers.com (832) 554-0980
Revision: M-ESCS-003
Maxim Silencers
Standard Terms and Conditions
with manufacturer’s instructions. The primary purpose of “factory black” standard coating is not aesthetic but for corrosion resistance
and shipping protection. No heat curing is available. If required, curing must be done in service at the direction of others.
No representative has the authority to make any representation, promise or agreement except as stated herein.
TAXES: The Purchaser shall pay to the Seller in addition to the purchase price, the amount of any excise, sales, privilege, or use tax,
local, state or federal, which is payable by the Seller because of the execution of this contract or sale or delivery of the apparatus
covered hereby. Seller shall collect applicable taxes in states where Seller has nexus, unless Buyer submits a valid tax exemption
certificate.
PATENTS: Notwithstanding any language to the contrary in specifications, purchase orders or elsewhere, Seller shall not be
responsible for any patent infringement, or claim of patent infringement with respect to products furnished in accordance with the
Purchaser's specifications or design requirements, and Purchaser shall indemnify and save Seller harmless from all claims, demands
or suits growing out of or based on any patent infringement or claim thereof, arising there from.
FORCE MAJEURE: Seller shall not be liable for any delay in delivery or for non-delivery , in whole or in part caused by the
occurrence of any contingency beyond the control either of Seller or suppliers to the Seller, including but not limited to war (whether
an actual declaration thereof is made or not), sabotage, insurrection, rebellion, riot or other act of civil disobedience, act of a public
enemy, failure or delay in transportation, act of any government or any agency or subdivision thereof, judicial action, labor dispute,
fire, accident explosion, epidemic, quarantine, restrictions, storm, flood, earthquake, or other act of God, shortage of labor, fuel, raw
material or machinery or technical failure, where Seller has exercised ordinary care in the prevention thereof. If any contingency
occurs, Seller may allocate production and deliveries among Seller's customers.
CONFIDENTIAL INFORMATION: All drawings, diagrams, specifications and other materials furnished by Seller and identified as
confidential relating to the use and service of articles furnished hereunder and the information therein are proprietary to Seller. Such
materials have been developed at great expense and they contain trade secrets of the Seller. Buyer may not reproduce or distribute
such materials except to Buyer's employees who may use the articles as part of their duties. All such materials relating to the article
supplied directly by Seller (except information as may be established to be in the public domain or disclosed pursuant to judicial
government action) shall be received in confidence and Buyer shall exercise reasonable care to hold such information in confidence.
TECHNICAL ASSISTANCE: Seller's warranty shall not be enlarged and no obligation or liability shall arise out of Seller's rendering of
technical advice, facilities or services in connection with Buyer's order for the goods furnished.
DISPUTES: This agreement is deemed to be entered into in Texas and to be a Texas contract and shall be governed and construed
in accordance with the laws of the State of Texas. Except as otherwise specifically provided for herein Seller and Buyer specifically
agree that any legal action brought relating to goods purchased or relating to this contract will be brought and tried in Texas. All
objections to venue are hereby waived by the Buyer, and the Buyer consents to service of process by certified mail addressed to the
same address as that address designated for delivery of the goods purchased hereunder. In the event of any suit for the collection of
funds instituted by the Seller, the prevailing party with respect to such collection matter shall be entitled to reasonable attorney's fees
as determined by the court to prevail in Texas.
47