Warning Chime System: Section
Warning Chime System: Section
Warning Chime System: Section
WCS
A
B
SECTION
WARNING CHIME SYSTEM C
E
CONTENTS
BASIC INSPECTION .................................... 3 PARKING BRAKE RELEASE WARNING CHIME F
: System Description ................................................11
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 PARKING BRAKE RELEASE WARNING CHIME
Work Flow ................................................................. 3 : Component Parts Location ....................................12 G
PARKING BRAKE RELEASE WARNING CHIME
SYSTEM DESCRIPTION .............................. 5 : Component Description .........................................12
WARNING CHIME SYSTEM ............................... 5 DIAGNOSIS SYSTEM (UNIFIED METER AND H
OVERALL SEQUENCE
C
JSNIA4485GB M
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM WCS
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
O
>> GO TO 2.
2.CHECK SYMPTOM P
• Check the symptom based on the information obtained from the customer.
• Check that any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS
1. Connect CONSULT and perform “Self Diagnostic Result”. Refer to MWI-117, "DTC Index".
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repair or replace malfunctioning parts.
>> GO TO 6.
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 1.
JSNIA0500GB G
JPNIA0764ZZ
L
UNIFIED METER AND A/C AMP.
The unified meter and A/C amp. transmits the buzzer output signal received from BCM with CAN communica-
tion line to the combination meter.
M
BCM
BCM receives signals from various units and transmits a buzzer output signal to the unified meter and A/C
amp. with CAN communication line if it judges that the warning buzzer should be activated. WCS
BCM warning function list
Warning functions Signal name
JPNIA1105ZZ
1. BCM 2. ABS actuator and electric unit (con- 3. Unified meter and A/C amp.
trol unit)
4. Front door switch (driver side) 5. Combination switch 6. Parking brake switch
(Lighting switch)
7. Seat belt buckle switch (driver side) 8. Combination meter
A. Dash side lower (passenger side) B. Hoodledge cover (LH) C. Behind cluster lid C
Unit Description
• Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer.
• Judges whether the parking brake is released from the vehicle speed signal received from the
Combination meter
unified meter and A/C amp. with CAN communication line and the parking brake switch signal
from the parking brake switch, and sounds the buzzer if necessary.
• Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to
BCM with CAN communication line.
Unified meter and A/C amp.
• Receives a buzzer output signal from BCM with CAN communication line and transmits it to
the combination meter by means of communication line.
Transmits signals provided by various units and switches to the unified meter and A/C amp. with
BCM
CAN communication line.
ABS actuator and electric unit
Transmits the vehicle speed signal to unified meter and A/C amp. with CAN communication line.
(control unit)
Seat belt buckle switch (driver
Transmits the seat belt buckle switch signal to the unified meter and A/C amp.
side)
F
JSNIA0167GB
G
LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000010576924
DESCRIPTION H
With ignition switch in OFF or ACC position, driver door open, and lighting switch in 1ST or 2ND position, the
light reminder warning chime will sound.
• BCM detects ignition switch in OFF or ACC position, front door switch (driver side) ON, and lighting switch in
1ST or 2ND position. And then transmits buzzer output signal (light reminder warning chime) to unified meter I
and A/C amp. with CAN communication line.
• Unified meter and A/C amp. transmits buzzer output signal (light reminder warning chime) to combination
meter with communication line. J
• When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled. K
• Lighting switch is at 1st or 2nd position
• Ignition switch is at OFF or ACC
• Front door switch (driver side) is ON L
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
• Lighting switch OFF M
• Ignition switch ON
• Front door switch (driver side) is OFF
WCS
JPNIA1105ZZ
1. BCM 2. ABS actuator and electric unit (con- 3. Unified meter and A/C amp.
trol unit)
4. Front door switch (driver side) 5. Combination switch 6. Parking brake switch
(Lighting switch)
7. Seat belt buckle switch (driver side) 8. Combination meter
A. Dash side lower (passenger side) B. Hoodledge cover (LH) C. Behind cluster lid C
Unit Description
Combination meter Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer.
Receives a buzzer output signal from BCM via CAN communication line and transmits it to the com-
Unified meter and A/C amp.
bination meter by means of communication line.
Judges the light warning conditions from the signals provided by various switches and transmits a
BCM
buzzer output signal to the unified meter and A/C amp. via CAN communication line if necessary.
Combination switch
Transmits the lighting switch position signal to BCM.
(Lighting switch)
Front door switch
Transmits the door switch signal to BCM.
(driver side)
JSNIA0168GB
D
SEAT BELT WARNING CHIME : System Description INFOID:0000000010576928
E
DESCRIPTION
With ignition switch turned ON and driver seat belt unfastened, seat belt warning chime will sound for approxi-
mately 6 seconds.
• BCM receives seat belt buckle switch signal from unified meter and A/C amp. with CAN communication line. F
• BCM detects ignition switch turned ON and seat belt buckle switch (driver side) ON. And then transmits
buzzer output signal (seat belt warning chime) to unified meter and A/C amp. with CAN communication line.
• Unified meter and A/C amp. transmits buzzer output signal (seat belt warning chime) to combination meter G
with communication line.
• When combination meter receives buzzer output signal (seat belt warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS H
If all of the following conditions are fulfilled.
• Ignition switch OFF→ON
• Seat belt buckle switch (driver side) is ON (driver seat belt not fastened)
I
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
• Ignition switch OFF J
• Seat belt buckle switch (driver side) is OFF (driver seat belt fastened)
WCS
JPNIA1105ZZ
1. BCM 2. ABS actuator and electric unit (con- 3. Unified meter and A/C amp.
trol unit)
4. Front door switch (driver side) 5. Combination switch 6. Parking brake switch
(Lighting switch)
7. Seat belt buckle switch (driver side) 8. Combination meter
A. Dash side lower (passenger side) B. Hoodledge cover (LH) C. Behind cluster lid C
Unit Description
Combination meter Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer.
• Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to
BCM via CAN communication line.
Unified meter and A/C amp.
• Receives a buzzer output signal from BCM via CAN communication line and transmits it to the
combination meter by means of communication line.
Judges the seat belt warning condition from the seat belt buckle switch signal received from the uni-
BCM fied meter and A/C amp. and transmits a buzzer output signal to the unified meter and A/C amp. via
CAN communication line if necessary.
Seat belt buckle switch
Refer to WCS-24, "Description".
(driver side)
JSNIA0036GB
D
PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000010576932
E
DESCRIPTION
• The unified meter and A/C amp. receives the vehicle speed signal from the ABS actuator and electric unit
(control unit) via CAN communication line and transmits it to the combination meter by means of communi-
cation line. F
• The combination meter judges whether the parking brake is released from the vehicle speed signal received
from the unified meter and A/C amp. and the parking brake switch signal from the parking brake switch, and
sounds the warning buzzer if necessary. G
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
• Vehicle speed is 7 km/h (4.3 MPH) or higher H
• Parking brake switch ON
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled. I
• Vehicle speed is approximately 3 km/h (1.9 MPH) or less
• Parking brake switch OFF
J
WCS
JPNIA1105ZZ
1. BCM 2. ABS actuator and electric unit (con- 3. Unified meter and A/C amp.
trol unit)
4. Front door switch (driver side) 5. Combination switch 6. Parking brake switch
(Lighting switch)
7. Seat belt buckle switch (driver side) 8. Combination meter
A. Dash side lower (passenger side) B. Hoodledge cover (LH) C. Behind cluster lid C
Unit Description
Judges whether the parking brake is released from the vehicle speed signal received from the
Combination meter unified meter and A/C amp. via CAN communication line and the parking brake switch signal from
the parking brake switch, and sounds the buzzer if necessary.
Receives a vehicle speed signal from ABS actuator and electric unit (control unit) via CAN com-
Unified meter and A/C amp.
munication line and transmits it to the combination meter by means of communication line.
ABS actuator and electric unit
Transmits the vehicle speed signal to unified meter and A/C amp. via CAN communication line.
(control unit)
Parking brake switch Transmits the parking brake switch signal to the combination meter.
MAIN
Display item [Unit] Description
SIGNALS H
Value of vehicle speed signal received from ABS actuator and electric unit (control
SPEED METER unit) with CAN communication line.
X
[km/h] or [mph] NOTE: I
655.35 is displayed when the malfunction signal is received.
Vehicle speed signal value transmitted to other units with CAN communication
SPEED OUTPUT line.
[km/h] or [mph]
X
NOTE: J
655.35 is displayed when the malfunction signal is received.
ODO OUTPUT
Odometer signal value transmitted to other units with CAN communication line.
[km/h] K
Value of the engine speed signal received from ECM with CAN communication
TACHO METER line.
X
[rpm] NOTE: L
8191.875 is displayed when the malfunction signal is received.
FUEL METER
X Fuel level indicated on combination meter.
[L]
M
Value of engine coolant temperature signal received from ECM with CAN commu-
W TEMP METER nication line.
X
[°C] or [°F] NOTE:
215 is displayed when the malfunction signal is input. WCS
FUEL CAP W/L Status of fuel filler cap warning display detected from fuel filler cap warning display
[On/Off] signal received from ECM via CAN communication.
ABS W/L Status of ABS warning lamp judged from ABS warning lamp signal received from O
[On/Off] ABS actuator and electric unit (control unit) with CAN communication line.
Status of VDC OFF indicator lamp judged from VDC OFF indicator lamp signal re-
VDC/TCS IND
[On/Off]
ceived from ABS actuator and electric unit (control unit) with CAN communication P
line.
SLIP IND Status of VDC warning lamp judged from VDC warning lamp signal received from
[On/Off] ABS actuator and electric unit (control unit) with CAN communication line.
DDS* W/L
B
This item is displayed, but cannot be monitored.
[Off]
LANE W/L Status of lane departure warning lamp judged from lane departure warning lamp
[On/Off] signal received from lane camera unit with CAN communication line. C
LDP IND Status of LDP ON indicator lamp judged from LDP ON indicator lamp signal re-
[On/Off] ceived from lane camera unit with CAN communication line.
E-SUS IND D
This item is displayed, but cannot be monitored.
[On/Off]
DCA IND Status of DCA switch indicator judged from meter display signal received from ICC
[On/Off] sensor integrated unit with CAN communication line. E
LCD
[B&P N, B&P I, ID NG, ROTAT, SFT Displays status of Intelligent Key system warning judged from meter display signal
P, INSRT, BATT, NO KY,OUTKY, LK received from BCM with CAN communication line. F
WN]
ACC TARGET Status of vehicle ahead detection indicator judged from meter display signal re-
[On/Off] ceived from ICC sensor integrated unit with CAN communication line.
G
ACC DISTANCE Status of set distance indicator judged from meter display signal received from
[Off, SHOR, MID, LONG] ICC sensor integrated unit with CAN communication line.
ACC OWN VHL Status of own vehicle indicator judged from meter display signal received from
H
[On/Off] ICC sensor integrated unit with CAN communication line.
Status of set vehicle speed indicator judged from meter display signal received
ACC SET SPEED
from ICC sensor integrated unit with CAN communication line.
I
ACC UNIT Status of display unit judged from meter display signal received from ICC sensor
[On/Off] integrated unit with CAN communication line.
SHIFT IND
[P, R, N, D, L, M1, M2, M3, M4, M5,
Status of shift position indicator judged from shift position signal and manual mode J
indicator signal received from TCM with CAN communication line.
M6, M7]
O/D OFF SW
This item is displayed, but cannot be monitored.
[Off] K
AT S MODE SW
Status of snow mode switch.
[On/Off]
AT P MODE SW L
This item is displayed, but cannot be monitored.
[Off]
M RANGE SW
Status of manual mode switch.
[On/Off] M
NM RANGE SW
Status of non-manual mode switch.
[On/Off]
AT SFT UP SW WCS
Status of A/T shift up switch.
[On/Off]
AT SFT DWN SW
Status of A/T shift down switch.
[On/Off] O
ST SFT UP SW
Status of paddle shifter up switch.
[On/Off]
ST SFT DWN SW
Status of paddle shifter down switch.
P
[On/Off]
COMP F/B SIG A/C compressor activation condition that ECM judges according to the water tem-
[On/Off] perature and the acceleration degree.
4WD LOCK SW
This item is displayed, but cannot be monitored.
[Off]
PKB SW
Status of parking brake switch.
[On/Off]
SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
K
NOTE:
P
*: This item is displayed, but is not used.
Display item
Description D
[Unit]
PUSH SW
Status of push button ignition switch judged by BCM.
[On/Off]
UNLK SEN-DR E
Status of unlock sensor judged by BCM.
[On/Off]
VEH SPEED 1 Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN
[Km/h or mph] communication line. F
KEY SW-SLOT
Status of key slot judged by BCM.
[On/Off]
TAIL LAMP SW G
Status of each switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM.
[On/Off] H
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
I
ACTIVE TEST
Display item
Description J
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
K
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
WCS
1.CHECK FUSE
Check for blown fuses.
Terminals
(+) Ignition switch position Value (Approx.)
(-)
Combination meter Terminal Signal name
1 Battery power supply OFF Battery voltage
M53 Ground
21 Ignition signal ON Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector and ground.
Combination meter
Continuity
Connector Terminal
Ground
5 Existed
M53
15 Existed
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
UNIFIED METER AND A/C AMP.
UNIFIED METER AND A/C AMP. : Diagnosis Procedure INFOID:0000000011008596
1.CHECK FUSE
Check for blown fuses.
D
Terminals
(+) Ignition switch position Value (Approx.)
(-)
Unified meter A/C amp. Terminal Signal name E
54 Battery power supply OFF Battery voltage
M67 41 ACC power supply Ground ACC Battery voltage
53 Ignition power supply ON Battery voltage
F
Check that the following fuse and fusible link are not blown.
WCS
Signal name Fuse and fusible link No.
L
Battery power supply O
10
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is P
blown.
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connectors.
3. Check voltage between BCM harness connector and ground.
Terminals
(+) (−) Voltage
BCM (Approx.)
Connector Terminal
Ground
M118 1
Battery voltage
M119 11
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M119 13 Existed
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
• The buzzer for warning chime system is installed in the combination meter. B
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000010576942
C
1.CHECK OPERATION OF METER BUZZER
1. Select “BUZZER” of “BCM” on CONSULT.
2. Perform “LIGHT WARN ALM” of “ACTIVE TEST”. D
Does meter buzzer beep?
YES >> INSPECTION END
NO >> GO TO 2. E
2.CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value. F
BUZZER
Under the condition of buzzer input : On
G
Except above : Off
Is the inspection result normal?
YES >> Replace combination meter. H
NO >> Replace BCM. Refer to BCS-93, "Removal and Installation".
Diagnosis Procedure INFOID:0000000010576943
I
1.CHECK POWER SUPPLY OF COMBINATION METER
Check power supply of combination meter. Refer to MWI-58, "COMBINATION METER : Diagnosis Proce-
J
dure".
Is the inspection result normal?
YES >> GO TO 2.
K
NO >> Repair power supply circuit of combination meter.
2.CHECK POWER SUPPLY OF UNIFIED METER AND A/C AMP.
Check power supply of unified meter and A/C amp. Refer to MWI-58, "COMBINATION METER : Diagnosis L
Procedure".
Is the inspection result normal?
YES >> INSPECTION END M
NO >> Repair power supply circuit of unified meter and A/C amp.
WCS
Transmits a seat belt buckle switch signal to the unified meter and A/C amp.
Component Function Check INFOID:0000000010576945
BUCKLE SW
When seat belt is fastened : Off
When seat belt is unfastened : On
Terminals
(+) (-) Voltage
Condition
Unified meter and A/C amp. (Approx.)
Connector Terminal
Ground
When driver seat belt is fastened 12 V
M66 9
When driver seat belt is unfastened 0V
Is the inspection result normal?
YES >> Replace unified meter and A/C amp.
NO >> GO TO 2.
2.CHECK SEAT BELT BUCKLE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect unified meter and A/C amp. connector and seat belt buckle switch (driver side) connector.
3. Check continuity between unified meter and A/C amp. harness connector and seat belt buckle switch
(driver side) harness connector.
Unified meter and A/C amp. Seat belt buckle switch (driver side)
Continuity
Connector Terminal Connector Terminal
M66 9 B503 61 Existed
4. Check harness continuity between unified meter and A/C amp. harness connector and ground.
WCS
JRNWD4438GB
WCS
JRNWD4439GB
JRNWD4440GB
WCS
JRNWD4441GB
JRNWD4442GB
WCS
JRNWD4443GB
JPNIA1324ZZ
PHYSICAL VALUES
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
1
Ground Battery power supply Input Ignition switch OFF Battery voltage
(BG)
2 Communication signal
Ground Output Ignition switch ON
(LG) (METER→ AMP.)
JSNIA0027GB
3 Communication signal
Ground Input Ignition switch ON
(GR) (AMP.→ METER)
JSNIA0027GB
5
Ground Ground — Ignition switch ON 0V
(B)
Ignition Charge warning lamp ON 0V
6
Ground Alternator signal Input switch
(W) Charge warning lamp OFF Battery voltage
ON
Ignition Air bag warning lamp ON 4V
7
Ground Air bag signal Input switch
(P) Air bag warning lamp OFF 0V
ON
Ignition Security warning lamp ON 0V
10
Ground Security indicator signal Input switch
(G) Security warning lamp OFF 12 V
OFF
15
Ground Ground — Ignition switch ON 0V
(B)
D
24 Communication signal
Ground Output Ignition switch ON
(BR) (LCD→ AMP.)
E
JSNIA0028GB
25 Communication signal
Ground Input Ignition switch ON
(Y) (AMP.→ LCD)
G
JSNIA0027GB
H
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit). I
Ignition Speedometer operated
26 Vehicle speed signal
Ground Input switch [When vehicle speed is ap-
(R) (8-pulse)
ON prox. 40 km/h (25 MPH)]
J
JSNIA0012GB
K
Parking brake ON 0V
L
Ignition
27
Ground Parking brake switch signal Input switch
(V) Parking brake OFF
ON
M
JSNIA0007GB
JSNIA0010GB
WCS
JRNWD4421GB
P
JRNWD4422GB
WCS
JRNWD4423GB
JRNWD4424GB
WCS
JRNWD4425GB
JRNWD4426GB
WCS
JRNWD4427GB
JRNWD4428GB
WCS
JRNWD4429GB
JRNWD4430GB
WCS
JRNWD4431GB
JRNWD4432GB
WCS
JRNWD4433GB
JRNWD4434GB
Fail-Safe INFOID:0000000011008641
FAIL-SAFE
Combination meter performs fail-safe operation when unified meter and A/C amp. communication is malfunc-
tion.
Solution for communication error between the unified meter and A/C amp. and combination meter.
Function Specifications A
Speedometer
Tachometer
Reset to zero by suspending communication. B
Fuel gauge
Engine coolant temperature gauge
Illumination control When suspending communication, change to nighttime mode. C
Information display The display turns off by suspending communication.
Buzzer The buzzer turns off by suspending communication.
ABS warning lamp D
VDC OFF indicator lamp
Brake warning lamp
The lamp turns on by suspending communication. E
CRUISE warning lamp
IBA OFF indicator lamp
Malfunction indicator lamp F
High beam indicator
Turn signal indicator lamp
G
Tail lamp indicator lamp
Warning lamp/indicator
Oil pressure warning lamp
lamp
A/T CHECK warning lamp H
VDC warning lamp
AWD warning lamp The lamp turns off by suspending communication.
I
Low tire pressure warning lamp
Key warning lamp
AFS OFF indicator lamp J
Lane departure warning lamp
LDP ON indicator lamp
Master warning lamp K
L
Refer to MWI-117, "DTC Index".
WCS
TERMINAL LAYOUT
JSNIA0097ZZ
PHYSICAL VALUES
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition Selector lever UP operation 0V
5 Manual mode shift up sig-
Ground Input switch
(L) nal Other than the above 12 V
ON
Ignition Paddle shifter up operation 0V
6
Ground Paddle shifter up signal Input switch
(BG) Other than the above 12 V
ON
Ignition
7 Communication signal
Ground Output switch —
(GR) (AMP. → METER)
ON
JSNIA0027GB
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
Ignition Speedometer operated
8 Vehicle speed signal
Ground Output switch [When vehicle speed is ap-
(L) (2-pulse)
ON prox. 40 km/h (25 MPH)]
JSNIA0015GB
11
Ignition Selector lever DS position 12 V C
Ground Non-manual mode signal Input switch
(G) Other than the above 0V
ON
Ignition
14 Communication signal
Ground Input switch — E
(BR) (LCD → AMP.)
ON
JSNIA0028GB
F
Ignition Selector lever down opera-
25 Manual mode shift down 0V
Ground Input switch tion
(V) signal
ON Other than the above 12 V G
Ignition Paddle shifter down opera-
26 0V
Ground Paddle shifter down signal Input switch tion
(G)
ON Other than the above 12 V H
Ignition I
27 Communication signal
Ground Input switch —
(LG) (METER → AMP.)
ON
J
JSNIA0027GB
NOTE:
The maximum voltage varies de- K
pending on the specification
(destination unit).
Ignition Speedometer operated L
28 Vehicle speed signal
Ground Output switch [When vehicle speed is ap-
(R) (8-pulse)
ON prox. 40 km/h (25 MPH)]
JSNIA0012GB
Ignition
30 O
Ground Parking brake switch signal Input switch
(V) Parking brake OFF
ON
P
JSNIA0007GB
Ignition
34 Communication signal
Ground Output switch —
(Y) (AMP. → LCD)
ON
JSNIA0027GB
Ignition
41
Ground ACC power supply Input switch — Battery voltage
(V)
ACC
Ignition
42
Ground Fuel level sensor signal Input switch —
(Y)
ON
SKIB8867E
45
Ground Ambient sensor signal Input — —
(P)
JSNIA0014GB
Ignition
53
Ground Ignition power supply Input switch — Battery voltage
(G)
ON
Ignition
54
Ground Battery power supply Input switch — Battery voltage
(BG)
OFF
Ignition
55
Ground Ground — switch — 0V
(B)
ON
56
Ground CAN-H — — — —
(L)
WCS
JRNWD4421GB
P
JRNWD4422GB
WCS
JRNWD4423GB
JRNWD4424GB
WCS
JRNWD4425GB
JRNWD4426GB
WCS
JRNWD4427GB
JRNWD4428GB
WCS
JRNWD4429GB
JRNWD4430GB
WCS
JRNWD4431GB
JRNWD4432GB
WCS
JRNWD4433GB
JRNWD4434GB
Fail-Safe INFOID:0000000011008645
FAIL-SAFE
The unified meter and A/C amp. activates the fail-safe control if CAN communication with each unit is malfunc-
tioning.
Function Specifications A
Speedometer
Tachometer
Reset to zero by suspending communication. B
Fuel gauge
Engine coolant temperature gauge
Illumination control When suspending communication, change to nighttime mode. C
Information display The display turns off by suspending communication.
Buzzer The buzzer turns off by suspending communication.
ABS warning lamp D
VDC OFF indicator lamp
Brake warning lamp
E
CRUISE warning lamp
IBA OFF indicator lamp The lamp turns on by suspending communication.
AWD warning lamp F
Low tire pressure warning lamp
Master warning lamp
G
Malfunction indicator lamp
Warning lamp/indicator
AFS OFF indicator lamp The lamp blinking caused by communication malfunction
lamp
High beam indicator H
Turn signal indicator lamp
Tail lamp indicator lamp
I
VDC warning lamp
Oil pressure warning lamp The lamp turns off by suspending communication.
A/T CHECK warning lamp J
Key warning lamp
Lane departure warning lamp
LDP ON indicator lamp K
RKE-TR/BD
NOTE:
Off P
The item is indicated, but not monitored.
PANIC button of the Intelligent Key is not pressed Off
RKE-PANIC
PANIC button of the Intelligent Key is pressed On
UNLOCK button of the Intelligent Key is not pressed Off
RKE-P/W OPEN
UNLOCK button of the Intelligent Key is pressed and held On
WCS
JPMIA0062ZZ
P
PHYSICAL VALUES
7 ON 0V
Ground Step lamp control Output Step lamp
(Y) OFF 12 V
LOCK
12 V
8 All doors, fuel lid (Actuator is activated)
Ground Output All doors, fuel lid
(V) LOCK Other than LOCK
0V
(Actuator is not activated)
UNLOCK
12 V
9 Driver door, fuel lid Driver door, fuel (Actuator is activated)
Ground Output
(G) UNLOCK lid Other than UNLOCK
0V
(Actuator is not activated)
UNLOCK
Rear RH door and 12 V
10 Rear RH door (Actuator is activated)
Ground rear LH door UN- Output
(BR) and rear LH door Other than UNLOCK
LOCK 0V
(Actuator is not activated)
11
Ground Battery power supply Input Ignition switch OFF Battery voltage
(R)
13
Ground Ground — Ignition switch ON 0V
(B)
OFF (LOCK indicator is
15 Battery voltage
Ground ACC indicator lamp Output Ignition switch not illuminated)
(Y)
ACC or ON 0V
Turn signal switch OFF 0V
PKID0926E
6.5 V
18
Ground
Turn signal LH
Output
Ignition switch C
(BG) (Front) ON Turn signal switch LH
D
PKID0926E
6.5 V
Other than under condition 5.0 V
E
19 Interior room lamp • Interior room lamp timer is activated.
Ground Output
(SB) control (Door is unlocked. etc...) 0V
• Welcome light function is activated.
F
Turn signal switch OFF 0V
G
20 Turn signal RH Ignition switch
Ground Output
(V) (Rear) ON Turn signal switch RH
H
PKID0926E
6.5 V
I
Turn signal switch OFF 0V
J
25 Ignition switch
Ground Turn signal LH (Rear) Output
(G) ON Turn signal switch LH
K
PKID0926E
6.5 V
L
26 OFF (Stopped) 0V
Ground Rear wiper Output Rear wiper
(P) ON (Operated) 12 V
M
JMKIA0062GB O
34 Luggage room anten- Ignition switch
Ground Output
(SB) na (−) OFF
P
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0063GB
JMKIA0063GB
E
61 Back door opener re- Back door re-
Ground Input
(W) quest switch quest switch OFF (Not pressed)
F
JPMIA0016GB
1.0 V
Intelligent Key warn- Intelligent Key Sounding 0V G
64
Ground ing buzzer (Engine Output warning buzzer
(L) Not sounding 12 V
room) (Engine room)
H
In stop position
I
65 Rear wiper stop posi-
Ground Input Rear wiper
(BG) tion
JPMIA0016GB J
1.0 V
Not in stop position 0V
WCS
JPMIA0594GB
8.5 - 9.0 V
JPMIA0594GB
8.5 - 9.0 V
ON (Door open) 0V
JPMIA0594GB
8.5 - 9.0 V
ON (Door open) 0V
JMKIA0063GB
JMKIA0063GB
I
When the driver JMKIA0062GB
JMKIA0063GB
L
M
When Intelligent Key is in
the passenger compart-
ment
WCS
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
During waiting
JMKIA0064GB
Remote keyless entry
83 Input/
Ground receiver communica-
(GR) Output
tion
JMKIA0065GB
JPMIA0041GB
1.4 V D
E
Front fog lamp switch ON
(Wiper volume dial 4)
F
JPMIA0037GB
JPMIA0039GB
I
1.3 V
J
Any of the conditions be-
low with all switches OFF
• Wiper volume dial 1
• Wiper volume dial 2 K
• Wiper volume dial 6
• Wiper volume dial 7
JPMIA0040GB
1.3 V L
WCS
JPMIA0041GB
1.4 V
Lighting switch HI
(Wiper volume dial 4)
JPMIA0036GB
1.3 V
JPMIA0037GB
1.3 V
JPMIA0039GB
1.3 V
1.3 V
90 Input/
Ground CAN-L — —
(P) Output
91 Input/
Ground CAN-H — —
(L) Output
C
92 Key slot illumina-
Ground Key slot illumination Output Blinking
(LG) tion
D
JPMIA0015GB
6.5 V
ON 0V
E
OFF (LOCK indicator is
93 Battery voltage
Ground ON indicator lamp Output Ignition switch not illuminated)
(V)
ON or ACC 0V
F
95 OFF 0V
Ground ACC relay control Output Ignition switch
(BG) ACC or ON 12 V
A/T shift selector (De- G
96
Ground tention switch) power Output — 12 V
(GR)
supply
K
JPMIA0016GB
1.0 V
ON (Pressed) 0V
L
101
Ground
Driver door request
Input
Driver door re- M
(SB) switch quest switch OFF (Not pressed)
WCS
JPMIA0016GB
1.0 V
JPMIA0041GB
1.4 V
JPMIA0037GB
1.3 V
Combination
107 Combination switch switch
Ground Input Turn signal switch RH
(LG) INPUT 1 (Wiper volume
dial 4)
JPMIA0036GB
1.3 V
JPMIA0038GB
1.3 V
JPMIA0039GB
1.3 V
JPMIA0041GB
1.4 V D
E
Lighting switch AUTO
(Wiper volume dial 4)
F
JPMIA0038GB
1.3 V
G
JPMIA0036GB
I
1.3 V
JPMIA0040GB
1.3 V L
1.3 V
O
JPMIA0041GB
1.4 V
JPMIA0037GB
1.3 V
Combination
109 Combination switch switch
Ground Input Lighting switch 2ND
(Y) INPUT 2 (Wiper volume
dial 4)
JPMIA0036GB
1.3 V
JPMIA0038GB
1.3 V
JPMIA0040GB
1.3 V
ON 0V
110
Ground Hazard switch Input Hazard switch
(G) OFF
JPMIA0012GB
1.1 V
JPMIA0156GB
8.7 V D
When bright outside of the
Close to 5 V
113 Ignition switch vehicle
Ground Optical sensor Input E
(P) ON When dark outside of the
Close to 0 V
vehicle
116
Ground Stop lamp switch 1 Input — Battery voltage
(BR) F
OFF (Brake pedal is not
0V
Stop lamp switch 2 depressed)
Stop lamp switch
(Without ICC) ON (Brake pedal is de- G
Battery voltage
118 pressed)
Ground Input
(P) Stop lamp switch OFF (Brake pedal is not de-
0V
Stop lamp switch 2 pressed) and ICC brake hold relay OFF H
(With ICC) Stop lamp switch ON (Brake pedal is de-
Battery voltage
pressed) or ICC brake hold relay ON
I
LOCK status J
(Unlock sensor switch
Front door lock as- OFF)
119
Ground sembly driver side Input Driver door
(SB)
(Unlock sensor)
JPMIA0594GB K
8.5 - 9.0 V
UNLOCK status
(Unlock switch sensor 0V L
ON)
When the Intelligent Key is inserted into key
12 V
121 slot
Ground Key slot switch Input M
(BR) When the Intelligent Key is not inserted into
0V
key slot
JPMIA0594GB
8.5 - 9.0 V
ON (Door open) 0V
JPMIA0013GB
10.2 V
Ignition switch OFF or ACC 12 V
138 OFF 0V
Ground Sensor power supply Output Ignition switch
(Y) ACC or ON 5.0 V
JPMIA0014GB
11.3 V
OFF 12 V
All switches OFF 0V
Lighting switch 1ST
Lighting switch HI
Combination
142 Combination switch switch Lighting switch 2ND
Ground Output
(BG) OUTPUT 5 (Wiper volume
dial 4)
Turn signal switch RH
JPMIA0031GB
10.7 V
All switches OFF
0V
(Wiper volume dial 4)
Front wiper switch HI
(Wiper volume dial 4)
Rear wiper switch INT
143 Combination switch Combination (Wiper volume dial 4)
Ground Output
(P) OUTPUT 1 switch Any of the conditions be-
low with all switches OFF
• Wiper volume dial 1
• Wiper volume dial 2
• Wiper volume dial 3 JPMIA0032GB
10.7 V
All switches OFF 0V I
Front fog lamp switch ON
Lighting switch 2ND
Combination
146 Combination switch switch Lighting switch PASS J
Ground Output
(SB) OUTPUT 4 (Wiper volume
dial 4)
Turn signal switch LH K
JPMIA0035GB
10.7 V
JPMIA0594GB WCS
8.5 - 9.0 V
ON (Door open) 0V
JRMWF4484GB
WCS
JRMWF4485GB
JRMWF4486GB
WCS
JRMWF4487GB
JRMWF4488GB
WCS
JRMWF4489GB
JRMWF4490GB
WCS
JRMWF4491GB
JRMWF4492GB
WCS
JRMWF4493GB
JRMWF4494GB
WCS
JRMWF4495GB
JRMWF4496GB
WCS
JRMWF4497GB
JRMWF4498GB
WCS
JRMWF4499GB
Fail-safe INFOID:0000000011008649 P
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
• U1000: CAN COMM
2
• U1010: CONTROL UNIT(CAN)
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is C
released
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
D
Diagnosis Procedure INFOID:0000000010576963
Perform a check for the parking brake switch signal circuit. Refer to BRC-99, "Diagnosis Procedure".
Is the inspection result normal? I
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK PARKING BRAKE SWITCH UNIT J
Perform a unit check for the parking brake switch. Refer to BRC-99, "Component Inspection".
Is the inspection result normal?
K
YES >> Replace the combination meter.
NO >> Replace the parking brake switch. Refer to PB-6, "Exploded View".
WCS
Light reminder warning chime does not sound even though headlamp is illuminated.
Diagnosis Procedure INFOID:0000000010576965
Perform the check for the seat belt buckle switch circuit. Refer to WCS-24, "Diagnosis Procedure".
Is the inspection result normal? J
YES >> Replace the unified meter and A/C amp.
NO >> Repair harness or connector.
4.CHECK SEAT BELT BUCKLE SWITCH UNIT K
Perform a unit check for the seat belt buckle switch. Refer to WCS-25, "Component Inspection".
Is the inspection result normal?
L
YES >> Replace the combination meter.
NO >> Replace the seat belt buckle. Refer to SB-8, "SEAT BELT BUCKLE : Removal and Installation".
WCS
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing Battery Terminal INFOID:0000000011008566
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
SEF289H
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.