Warning Chime System: Section
Warning Chime System: Section
Warning Chime System: Section
SECTION
WARNING CHIME SYSTEM
WCS B
E
CONTENTS
BASIC INSPECTION .................................... 3 PARKING BRAKE RELEASE WARNING CHIME F
: System Description ................................................11
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 PARKING BRAKE RELEASE WARNING CHIME
Work Flow ................................................................. 3 : Component Parts Location ....................................12 G
PARKING BRAKE RELEASE WARNING CHIME
FUNCTION DIAGNOSIS ............................... 5 : Component Description .........................................12
WARNING CHIME SYSTEM ............................... 5 DIAGNOSIS SYSTEM (UNIFIED METER AND H
OVERALL SEQUENCE
C
JSNIA0456GB M
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM WCS
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
O
>> GO TO 2.
2.CHECK SYMPTOM P
• Check the symptom based on the information obtained from the customer.
• Check that any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT-III SELF-DIAGNOSIS RESULTS
Connect CONSULT-III and perform self-diagnosis. Refer to MWI-40, "CONSULT-III Function (METER/M&A)".
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repair or replace malfunctioning parts.
>> GO TO 6.
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 1.
JSNIA0500GB G
JPNIA0764ZZ
L
UNIFIED METER AND A/C AMP.
The unified meter and A/C amp. transmits the buzzer output signal received from BCM with CAN communica-
tion line to the combination meter.
M
BCM
BCM receives signals from various units and transmits a buzzer output signal to the unified meter and A/C
amp. with CAN communication line if it judges that the warning buzzer should be activated. WCS
BCM warning function list
Warning functions Signal name
JPNIA0869ZZ
1. BCM 2. ABS actuator and electric unit (con- 3. Unified meter and A/C amp.
trol unit)
4. Front door switch (driver side) 5. Combination switch 6. Parking brake switch
(Lighting switch)
7. Seat belt buckle switch (driver side) 8. Combination meter
A. Dash side lower (passenger side) B. Hoodledge cover (LH) C. Behind cluster lid C
Unit Description
• Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer.
• Judges whether the parking brake is released from the vehicle speed signal received from the
Combination meter
unified meter and A/C amp. with CAN communication line and the parking brake switch signal
from the parking brake switch, and sounds the buzzer if necessary.
• Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to
BCM with CAN communication line.
Unified meter and A/C amp.
• Receives a buzzer output signal from BCM with CAN communication line and transmits it to
the combination meter by means of communication line.
Transmits signals provided by various units to the unified meter and A/C amp. with CAN com-
BCM
munication line.
ABS actuator and electric unit
Transmits the vehicle speed signal to BCM with CAN communication line.
(control unit)
Seat belt buckle switch (driver
Transmits a seat belt buckle switch signal to the unified meter and A/C amp.
side)
F
JSNIA0167GB
G
LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000003135084
DESCRIPTION H
With ignition switch in OFF or ACC position, driver door open, and lighting switch in 1ST or 2ND position, the
light reminder warning chime will sound.
• BCM detects ignition switch in OFF or ACC position, front door switch (driver side) ON, and lighting switch in
1ST or 2ND position. And then transmits buzzer output signal (light reminder warning chime) to unified meter I
and A/C amp. with CAN communication line.
• Unified meter and A/C amp. transmits buzzer output signal (light reminder warning chime) to combination
meter with communication line. J
• When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled. K
• Lighting switch is at 1st or 2nd position
• Ignition switch is at OFF or ACC
• Front door switch (driver side) is ON L
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
• Lighting switch OFF M
• Ignition switch ON
• Front door switch (driver side) is OFF
WCS
JPNIA0869ZZ
1. BCM 2. ABS actuator and electric unit (con- 3. Unified meter and A/C amp.
trol unit)
4. Front door switch (driver side) 5. Combination switch 6. Parking brake switch
(Lighting switch)
7. Seat belt buckle switch (driver side) 8. Combination meter
A. Dash side lower (passenger side) B. Hoodledge cover (LH) C. Behind cluster lid C
Unit Description
Combination meter Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer.
Receives a buzzer output signal from BCM via CAN communication line and transmits it to the com-
Unified meter and A/C amp.
bination meter by means of communication line.
Judges the light warning conditions from the signals provided by various switches and transmits a
BCM
buzzer output signal to the unified meter and A/C amp. via CAN communication line if necessary.
Combination switch
Transmits the lighting switch position signal to BCM.
(Lighting switch)
Front door switch
Transmits the door switch signal to BCM.
(driver side)
JSNIA0168GB
D
SEAT BELT WARNING CHIME : System Description INFOID:0000000003135088
E
DESCRIPTION
With ignition switch turned ON and driver seat belt unfastened, seat belt warning chime will sound for approxi-
mately 6 seconds.
• BCM receives seat belt buckle switch signal from unified meter and A/C amp. with CAN communication line. F
• BCM detects ignition switch turned ON and seat belt buckle switch (driver side) ON. And then transmits
buzzer output signal (seat belt warning chime) to unified meter and A/C amp. with CAN communication line.
• Unified meter and A/C amp. transmits buzzer output signal (seat belt warning chime) to combination meter G
with communication line.
• When combination meter receives buzzer output signal (seat belt warning chime), it sounds the buzzer.
WARNING OPERATION CONDITIONS H
If all of the following conditions are fulfilled.
• Ignition switch OFF→ON
• Seat belt buckle switch (driver side) is ON (driver seat belt not fastened)
I
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
• Ignition switch OFF J
• Seat belt buckle switch (driver side) is OFF (driver seat belt fastened)
WCS
JPNIA0869ZZ
1. BCM 2. ABS actuator and electric unit (con- 3. Unified meter and A/C amp.
trol unit)
4. Front door switch (driver side) 5. Combination switch 6. Parking brake switch
(Lighting switch)
7. Seat belt buckle switch (driver side) 8. Combination meter
A. Dash side lower (passenger side) B. Hoodledge cover (LH) C. Behind cluster lid C
Unit Description
Combination meter Receives a buzzer output signal from the unified meter and A/C amp. and sounds the buzzer.
• Receives the seat belt buckle switch signal from the seat belt buckle switch and transmits it to
BCM via CAN communication line.
Unified meter and A/C amp.
• Receives a buzzer output signal from BCM via CAN communication line and transmits it to the
combination meter by means of communication line.
Judges the seat belt warning condition from the seat belt buckle switch signal received from the uni-
BCM fied meter and A/C amp. and transmits a buzzer output signal to the unified meter and A/C amp. via
CAN communication line if necessary.
Seat belt buckle switch
Refer to WCS-24, "Description".
(driver side)
JSNIA0036GB
D
PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000003135092
E
DESCRIPTION
• The unified meter and A/C amp. receives the vehicle speed signal from the ABS actuator and electric unit
(control unit) via CAN communication line and transmits it to the combination meter by means of communi-
cation line. F
• The combination meter judges whether the parking brake is released from the vehicle speed signal received
from the unified meter and A/C amp. and the parking brake switch signal from the parking brake switch, and
sounds the warning buzzer if necessary. G
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
• Vehicle speed is 7 km/h (4.3 MPH) or higher H
• Parking brake switch ON
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled. I
• Vehicle speed is approximately 3 km/h (1.9 MPH) or less
• Parking brake switch OFF
J
WCS
JPNIA0869ZZ
1. BCM 2. ABS actuator and electric unit (con- 3. Unified meter and A/C amp.
trol unit)
4. Front door switch (driver side) 5. Combination switch 6. Parking brake switch
(Lighting switch)
7. Seat belt buckle switch (driver side) 8. Combination meter
A. Dash side lower (passenger side) B. Hoodledge cover (LH) C. Behind cluster lid C
Unit Description
Judges whether the parking brake is released from the vehicle speed signal received from the
Combination meter unified meter and A/C amp. via CAN communication line and the parking brake switch signal from
the parking brake switch, and sounds the buzzer if necessary.
Receives a vehicle speed signal from ABS actuator and electric unit (control unit) via CAN com-
Unified meter and A/C amp.
munication line and transmits it to the combination meter by means of communication line.
ABS actuator and electric unit
Transmits the vehicle speed signal to combination meter via CAN communication line.
(control unit)
Parking brake switch Refer to MWI-65, "Description".
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items. H
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × × K
Wiper and washer WIPER × ×
Turn signal and hazard warning lamps FLASHER × × ×
L
— AIR CONDITONER*
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
M
Combination switch COMB SW ×
Body control system BCM ×
IVIS - NATS IMMU × × WCS
Interior room lamp battery saver BATTERY SAVER × × ×
— TRUNK* × ×
O
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER × × P
TPMS TPMS (AIR PRESSURE MONITOR) × × ×
NOTE:
*: This item is displayed, but is not used.
IGN Counter
IGN counter indicates the number of times that ignition switch is turned ON after DTC is detected.
• The number is 0 when a malfunction is detected now.
• The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition whenever ignition
switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
BUZZER
BUZZER : CONSULT-III Function (BCM - BUZZER) INFOID:0000000003135097
DATA MONITOR
Display item A
Description
[Unit]
VEH SPEED 1 Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN
[Km/h] communication line.
B
PUSH SW
Status of push button ignition switch judged by BCM.
[On/Off]
UNLK SEN-DR C
Status of unlock sensor judged by BCM.
[On/Off]
KEY SW-SLOT
Status of key slot judged by BCM.
[On/Off]
D
TAIL LAMP SW
Status of each switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM. E
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
F
ACTIVE TEST
Display item G
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off). H
ID REGIST WARNING The ID regist warning chime operation can be checked by operating the relevant function (On/Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
I
WCS
1.CHECK FUSE
Check for blown fuses.
Terminals
(+) Ignition switch position Value (Approx.)
(-)
Combination meter Terminal Signal name
1 Battery power supply OFF Battery voltage
M53 23 ACC power supply Ground ACC Battery voltage
21 Ignition signal ON Battery voltage
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector and ground.
Combination meter
Continuity
Connector Terminal
5 Ground Existed
M53 15 Existed
22 Existed
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
UNIFIED METER AND A/C AMP.
UNIFIED METER AND A/C AMP. : Diagnosis Procedure INFOID:0000000003554659
1.CHECK FUSE
Check for blown fuses.
Terminals
E
(+) Ignition switch position Value (Approx.)
(-)
Unified meter A/C amp. Terminal Signal name
54 Battery power supply OFF Battery voltage F
M67 41 ACC power supply Ground ACC Battery voltage
53 Ignition signal ON Battery voltage
G
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between unified meter and A/C amp. and fuse.
H
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect unified meter and A/C amp. connector. I
3. Check continuity between unified meter and A/C amp. harness connector and ground.
Terminals
(+) (−) Voltage
BCM (Approx.)
Connector Terminal
Ground
M118 1
Battery voltage
M119 11
Is the measurement value normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
BCM
Continuity
Connector Terminal Ground
M119 13 Existed
Does continuity exist?
YES >> INSPECTION END
NO >> Repair harness or connector.
• The buzzer for warning chime system is installed in the combination meter. B
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000003135103
C
1.CHECK OPERATION OF METER BUZZER
1. Select “BUZZER” of “BCM” on CONSULT-III.
2. Perform “LIGHT WARN ALM” of “ACTIVE TEST”. D
Does meter buzzer beep?
YES >> INSPECTION END
NO >> GO TO 2. E
2.CHECK UNIFIED METER AND A/C AMP. INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value. F
BUZZER
Under the condition of buzzer input : On
G
Except above : Off
Is the inspection result normal?
YES >> Replace combination meter. H
NO >> Replace BCM. Refer to BCS-84, "Removal and Installation".
Diagnosis Procedure INFOID:0000000003135104
I
1.CHECK POWER SUPPLY OF COMBINATION METER
Check power supply of combination meter. Refer to WCS-20, "COMBINATION METER : Diagnosis Proce-
J
dure".
Is the inspection result normal?
YES >> GO TO 2.
K
NO >> Repair power supply circuit of combination meter.
2.CHECK POWER SUPPLY OF UNIFIED METER AND A/C AMP.
Check power supply of unified meter and A/C amp. Refer to WCS-20, "UNIFIED METER AND A/C AMP. : L
Diagnosis Procedure".
Is the inspection result normal?
YES >> INSPECTION END M
NO >> Repair power supply circuit of unified meter and A/C amp.
WCS
Transmits a seat belt buckle switch signal to the unified meter and A/C amp.
Component Function Check INFOID:0000000003135106
BUCKLE SW
When seat belt is fastened : Off
When seat belt is unfastened : On
Terminals
(+) (-) Voltage
Condition
Unified meter and A/C amp. (Approx.)
Connector Terminal
Ground
When driver seat belt is fastened 12 V
M66 9
When driver seat belt is unfastened 0V
Is the inspection result normal?
YES >> Replace unified meter and A/C amp.
NO >> GO TO 2.
2.CHECK SEAT BELT BUCKLE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect unified meter and A/C amp. connector and seat belt buckle switch (driver side) connector.
3. Check continuity between unified meter and A/C amp. harness connector and seat belt buckle switch
(driver side) harness connector.
Unified meter and A/C amp. Seat belt buckle switch (driver side)
Continuity
Connector Terminal Connector Terminal
M66 9 B13 1 Existed
4. Check harness continuity between unified meter and A/C amp. harness connector and ground.
WCS
JCNWM0721GB
WCS
JCNWM0722GB
JCNWM0723GB
WCS
JCNWM0724GB
JSNIA0457ZZ
PHYSICAL VALUES
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(GR)
OFF
Ignition
2 Communication signal
Ground Output switch —
(LG) (METER→ AMP.)
ON
JSNIA0027GB
Ignition
3 Communication signal
Ground Input switch —
(GR) (AMP.→ METER)
ON
JSNIA0027GB
Ignition
5
Ground Ground — switch — 0V
(B)
ON
Ignition Charge warning lamp ON 0V
6
Ground Alternator signal Input switch
(P) Charge warning lamp OFF Battery voltage
ON
Ignition Air bag warning lamp ON 4V
7
Ground Air bag signal Input switch
(LG) Air bag warning lamp OFF 0V
ON
Ignition Security warning lamp ON 0V
10
Ground Security signal Input switch
(G) Security warning lamp OFF 12 V
OFF
G
Ignition
24 Communication signal
Ground Output switch —
(BR) (LCD→ AMP.)
ON H
JSNIA0028GB
Ignition
25 Communication signal J
Ground Input switch —
(Y) (AMP.→ LCD)
ON
JSNIA0027GB K
NOTE:
The maximum voltage varies de-
pending on the specification L
(destination unit).
Ignition Speedometer operated
26 Vehicle speed signal
Ground Input switch [When vehicle speed is ap-
(R) (8-pulse) M
ON prox. 40 km/h (25 MPH)]
WCS
JSNIA0012GB
Parking brake ON 0V
O
Ignition
27
Ground Parking brake switch signal Input switch
(V) Parking brake OFF P
ON
JSNIA0007GB
JSNIA0010GB
WCS
JCNWM0708GB
P
JCNWM0709GB
WCS
JCNWM0710GB
JCNWM0711GB
WCS
JCNWM0712GB
JCNWM0713GB
WCS
JCNWM0714GB
JCNWM0715GB
WCS
JCNWM0716GB
P
Fail-Safe INFOID:0000000003554726
FAIL-SAFE
Combination meter performs fail-safe operation when unified meter and A/C amp. communication is malfunc-
tion.
Solution for communication error between the unified meter and A/C amp. and combination meter.
Function Specifications
Speedometer
Tachometer
Reset to zero by suspending communication.
Fuel gauge
Water temperature gauge
Illumination control When suspending communication, change to nighttime mode.
Information display The display turns off by suspending communication.
Buzzer The buzzer turns off by suspending communication.
ABS warning lamp
VDC OFF indicator lamp
SLIP indicator lamp The lamp turns on by suspending communication.
Brake warning lamp
CRUISE warning lamp
High beam indicator
Turn signal indicator lamp
Light indicator lamp
TERMINAL LAYOUT
JSNIA0097ZZ
PHYSICAL VALUES D
Terminal No.
Description E
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition Selector lever UP operation 0V F
5 Manual mode shift up sig-
Ground Input switch
(L) nal Other than the above 12 V
ON
G
Ignition
7 Communication signal
Ground Output switch — H
(GR) (AMP. → METER)
ON
SKIA3362E I
NOTE:
The maximum voltage varies de-
pending on the specification J
(destination unit).
Ignition Speedometer operated
8 Vehicle speed signal output
Ground Output switch [When vehicle speed is ap-
(L) (2-pulse) K
ON prox. 40 km/h (25 MPH)]
L
JSNIA0015GB
P
Ignition
14 Communication signal
Ground Input switch —
(BR) (LCD → AMP.)
ON
JSNIA0028GB
Ignition
27 Communication signal
Ground Input switch —
(LG) (METER → AMP.)
ON
SKIA3361E
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
Ignition Speedometer operated
28 Vehicle speed signal output
Ground Output switch [When vehicle speed is ap-
(R) (8-pulse)
ON prox. 40 km/h (25 MPH)]
JSNIA0012GB
Parking brake ON 0V
Ignition
30
Ground Parking brake switch signal Input switch
(V) Parking brake OFF
ON
JSNIA0007GB
Ignition
34 Communication signal
Ground Output switch —
(Y) (AMP. → LCD)
ON
JSNIA0027GB
Ignition
41
Ground ACC power supply Input switch — Battery voltage
(V)
ACC
Ignition
42
Ground Fuel level sensor signal Input switch —
(Y)
ON
JSNIA0013GB
45 C
Ground Ambient sensor signal Input — —
(P)
JSNIA0014GB D
Ignition
53
Ground Ignition signal Input switch — Battery voltage
(G)
ON E
Ignition
54
Ground Battery power supply Input switch — Battery voltage
(Y)
OFF
F
Ignition
55
Ground Ground — switch — 0V
(B)
ON
G
56
Ground CAN-H — — — —
(L)
WCS
JCNWM0708GB
WCS
JCNWM0709GB
JCNWM0710GB
WCS
JCNWM0711GB
JCNWM0712GB
WCS
JCNWM0713GB
JCNWM0714GB
WCS
JCNWM0715GB
JCNWM0716GB
Fail-Safe INFOID:0000000003554730
FAIL-SAFE
The unified meter and A/C amp. activates the fail-safe control if CAN communication with each unit is malfunc-
tioning.
Function Specifications A
Speedometer
Tachometer
Reset to zero by suspending communication. B
Fuel gauge
Water temperature gauge
Illumination control When suspending communication, change to nighttime mode. C
Information display The display turns off by suspending communication.
Buzzer The buzzer turns off by suspending communication.
ABS warning lamp D
VDC OFF indicator lamp
SLIP indicator lamp
E
Brake warning lamp The lamp turns on by suspending communication.
CRUISE warning lamp
AWD warning lamp F
Low tire pressure warning lamp
AFS OFF indicator lamp The lamp blinking caused by communication malfunction
G
Warning lamp/indicator High beam indicator
lamp Turn signal indicator lamp
Light indicator lamp H
Oil pressure warning lamp
Malfunction indicator lamp
The lamp turns off by suspending communication. I
A/T CHECK warning lamp
Key warning lamp
Lane departure warning lamp J
LDP ON indicator lamp
Master warning lamp
K
DTC Index INFOID:0000000003554731
L
Display contents of CON-
Time Diagnostic item is detected when ... Refer to
SULT-III
CAN COMM CIRCUIT When unified meter and A/C amp. is not transmitting or receiving CAN
CRNT, 1 - 39 MWI-44 M
[U1000] communication signal for 2 seconds or more.
CONTROL UNIT (CAN) When detecting error during the initial diagnosis of CAN controller of
CRNT, 1 - 39 MWI-45
[U1010] unified meter and A/C amp.
WCS
If a communication error is present in the communication line between
COMM ERROR 1
CRNT, 1 - 39 unified meter and A/C amp. and combination meter for 2 seconds or MWI-46
[B2201]
more.
If a communication error is present in the communication line between O
COMM ERROR 2
CRNT, 1 - 39 unified meter and A/C amp. and combination meter for 2 seconds or MWI-48
[B2202]
more.
VEHICLE SPEED The abnormal vehicle speed signal is input from ABS actuator and elec- P
CRNT, 1 - 39 MWI-50
[B2205] tric unit (control unit) for 2 seconds or more.
ENGINE SPEED If ECM continuously transmits abnormal engine speed signals for 2 sec-
CRNT, 1 - 39 MWI-51
[B2267] onds or more.
WATER TEMP If ECM continuously transmits abnormal engine coolant temperature
CRNT, 1 - 39 MWI-52
[B2268] signals for 60 seconds or more.
The key ID that the key slot receives does not accord with the fourth
Yet
key ID registered to BCM.
CONFIRM ID4 WCS
The key ID that the key slot receives accords with the fourth key ID
DONE
registered to BCM.
The key ID that the key slot receives does not accord with the third
Yet O
key ID registered to BCM.
CONFIRM ID3
The key ID that the key slot receives accords with the third key ID
DONE
registered to BCM.
The key ID that the key slot receives does not accord with the sec-
P
Yet
ond key ID registered to BCM.
CONFIRM ID2
The key ID that the key slot receives accords with the second key
DONE
ID registered to BCM.
WCS
JPMIA0062ZZ
P
PHYSICAL VALUES
7 ON 0V
Ground Step lamp Output Step lamp
(Y) OFF Battery voltage
LOCK
Battery voltage
8 All doors, fuel lid (Actuator is activated)
Ground Output All doors
(V) LOCK Other than LOCK
0V
(Actuator is not activated)
UNLOCK
Battery voltage
9 Driver door, fuel lid (Actuator is activated)
Ground Output Driver door
(G) UNLOCK Other than UNLOCK
0V
(Actuator is not activated)
UNLOCK
Rear RH door and Battery voltage
10 Rear RH door (Actuator is activated)
Ground rear LH door UN- Output
(BR) and rear LH door Other than UNLOCK
LOCK 0V
(Actuator is not activated)
11
Ground Battery power supply Input Ignition switch OFF Battery voltage
(R)
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral
position
Push-button ignition
14
Ground switch illumination Output Tail lamp
(W) ON
ground
JSNIA0010GB
17
Ground
Turn signal RH
Output
Ignition switch C
(W) (Front) ON Turn signal switch RH
D
PKID0926E
6.5 V
Turn signal switch OFF 0V
E
G
PKID0926E
6.5 V
PKID0926E K
6.5 V
OPEN
(Back door opener actuator Battery voltage L
23 is activated)
Ground Back door opening Output Back door
(G) Other than OPEN
(Back door opener actuator 0V
M
is not activated)
Turn signal switch OFF 0V
WCS
25 Ignition switch
Ground Turn signal LH (Rear) Output
(G) ON Turn signal switch LH O
PKID0926E
P
6.5 V
26 OFF (Stopped) 0V
Ground Rear wiper Output Rear wiper
(G) ON (Operated) Battery voltage
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
When the back
38 Rear bumper anten- door request
Ground Output
(B) na (−) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
J
61 Back door opener re- Back door re-
Ground Input
(W) quest switch quest switch OFF (Not pressed)
K
JPMIA0016GB
1.0 V
L
64 Request switch buzz- Request switch Sounding 0V
Ground Output
(V) er buzzer Not sounding Battery voltage
M
WCS
65 Rear wiper stop posi- In stop position
Ground Input Rear wiper
(O) tion
JPMIA0016GB O
1.0 V
Not in stop position 0V
P
JPMIA0011GB
11.8 V
ON (Door open) 0V
Pressed 0V
JPMIA0011GB
11.8 V
JPMIA0011GB
11.8 V
ON (Door open) 0V
JPMIA0011GB
11.8 V
ON (Door open) 0V
JMKIA0062GB
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
JMKIA0062GB
I
73 Room antenna 2 (+) Ignition switch
Ground Output
(G) (Center console) OFF
J
JMKIA0063GB
L
M
When Intelligent Key is in
the antenna detection area
WCS
JMKIA0062GB
When the pas-
74 Passenger door an- senger door re-
Ground Output
(SB) tenna (−) quest switch is O
operated with ig-
nition switch OFF
When Intelligent Key is not P
in the antenna detection
area
JMKIA0063GB
JMKIA0063GB
JMKIA0062GB
When the driver
76 Driver door antenna door request
Ground Output
(V) (−) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
JMKIA0062GB
When the driver
77 Driver door antenna door request
Ground Output
(LG) (+) switch is operat-
ed with ignition
switch OFF
When Intelligent Key is not
in the antenna detection
area
JMKIA0063GB
JMKIA0062GB
E
When Intelligent Key is not
in the passenger compart-
ment
F
JMKIA0063GB
JMKIA0062GB
I
79 Room antenna (+) Ignition switch
Ground Output
(BR) (Instrument panel) OFF
J
JMKIA0063GB
L
Ignition switch is pressed Just after pressing ignition
80 NATS antenna amp Input/
Ground During waiting while inserting the key into switch. Pointer of tester should
(GR) (Built in key slot) Output
the key slot. move. M
Ignition switch is pressed Just after pressing ignition
81 NATS antenna amp Input/
Ground During waiting while inserting the key into switch. Pointer of tester should
(W) (Built in key slot) Output
the key slot. move.
WCS
82 Ignition relay [Fuse OFF or ACC 0V
Ground Output Ignition switch
(R) block (J/B)] control ON Battery voltage
O
During waiting
JMKIA0064GB
JMKIA0065GB
JPMIA0041GB
1.4 V
JPMIA0037GB
JPMIA0039GB
1.3 V
1.3 V
JPMIA0041GB
1.4 V D
E
Lighting switch HI
(Wiper intermittent dial 4)
F
JPMIA0036GB
1.3 V
G
JPMIA0037GB
I
1.3 V
JPMIA0039GB
1.3 V L
1.3 V
Push-button igni- Pressed 0V O
89 Push-button ignition
Ground Input tion switch (push
(BR) switch (Push switch) Not pressed Battery voltage
switch)
90 Input/ P
Ground CAN-L — —
(P) Output
91 Input/
Ground CAN-H — —
(L) Output
JPMIA0015GB
6.5 V
ON 0V
95 OFF 0V
Ground ACC relay control Output Ignition switch
(O) ACC or ON Battery voltage
Control device (De-
96
Ground tention switch) power Output — Battery voltage
(GR)
supply
JPMIA0016GB
1.0 V
ON (Pressed) 0V
JPMIA0016GB
1.0 V
1.4 V
F
G
Turn signal switch LH
H
JPMIA0037GB
1.3 V
Combination
107 Combination switch switch
Ground Input Turn signal switch RH J
(LG) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0036GB
1.3 V K
1.3 V
WCS
O
Front washer switch ON
JPMIA0039GB
P
1.3 V
JPMIA0041GB
1.4 V
JPMIA0038GB
1.3 V
JPMIA0036GB
1.3 V
JPMIA0040GB
1.3 V
1.3 V
JPMIA0041GB
1.4 V D
F
JPMIA0037GB
1.3 V
G
Combination
109 Combination switch switch
H
Ground Input Lighting switch 2ND
(Y) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0036GB
I
1.3 V
JPMIA0038GB
1.3 V L
WCS
JPMIA0040GB
1.3 V
ON 0V O
P
110
Ground Hazard switch Input Hazard switch
(G) OFF
JPMIA0012GB
1.1 V
LOCK or UNLOCK
111 Steering lock unit Input/
Ground Steering lock
(Y) communication Output
JMKIA0066GB
LOCK status
Front door lock as- (Unlock sensor switch
119 OFF)
Ground sembly driver side Input Driver door
(SB)
(unlock sensor)
JPMIA0012GB
1.1 V
UNLOCK status
0V
(Unlock switch sensor ON)
121 When the key is inserted into key slot Battery voltage
Ground Key slot switch Input
(BR) When the key is not inserted into key slot 0V
122 OFF 0V
Ground ACC feedback signal Input Ignition switch
(V) ACC or ON Battery voltage
JPMIA0011GB
11.8 V D
ON (Door open) 0V
JPMIA0013GB
10.2 V G
Ignition switch OFF or ACC Battery voltage
ON (Tail lamps OFF) 9.5 V
H
NOTE:
The pulse width of this wave is
varied by the illumination bright-
ening/dimming level. I
Push-button igni-
133 Push-button ignition
Ground Output tion switch illumi- ON (Tail lamps ON)
(W) switch illumination
nation J
JPMIA0159GB K
OFF 0V
Standby state
OCC3881D
OCC3880D
JPMIA0014GB
11.3 V
OFF Battery voltage
All switch OFF 0V
Lighting switch 1ST
Lighting switch HI
Combination
142 Combination switch switch Lighting switch 2ND
Ground Output
(O) OUTPUT 5 (Wiper intermit-
tent dial 4)
Turn signal switch RH
JPMIA0031GB
10.7 V
All switch OFF
0V
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
Rear wiper switch INT
143 Combination switch Combination (Wiper intermittent dial 4)
Ground Output
(P) OUTPUT 1 switch Any of the conditions below
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3 JPMIA0032GB
10.7 V
All switch OFF 0V I
Front fog lamp switch ON
Lighting switch 2ND
Combination
146 Combination switch switch Lighting switch PASS J
Ground Output
(SB) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH K
JPMIA0035GB
10.7 V
JPMIA0011GB WCS
11.8 V
JPMIA0011GB
11.8 V
ON (Door open) 0V
JCMWM1398GB
WCS
JCMWM1399GB
JCMWM1400GB
WCS
JCMWM1401GB
JCMWM1402GB
WCS
JCMWM1403GB
JCMWM1404GB
Fail-safe INFOID:0000000003777746
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
• U1000: CAN COMM CIRCUIT
2
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
3
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
NOTE:
The details of time display are as follows.
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data and IGN Counter, refer to
BCS-16, "COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)".
Tire pressure
Freeze Frame Intelligent Key Reference
CONSULT display Fail-safe monitor warning
Data warning lamp ON page
lamp ON
No DTC is detected.
further testing — — — — —
may be required.
U1000: CAN COMM CIRCUIT — — — — BCS-37
U1010: CONTROL UNIT (CAN) — — — — BCS-38
U0415: VEHICLE SPEED SIG — — — — BCS-39
B2013: ID DISCORD BCM-S/L × × — — SEC-48
B2014: CHAIN OF S/L-BCM × × — — SEC-49
B2190: NATS ANTENNA AMP × — — — SEC-42
B2191: DIFFERENCE OF KEY × — — — SEC-45
B2192: ID DISCORD BCM-ECM × — — — SEC-46
B2193: CHAIN OF BCM-ECM × — — — SEC-47
B2553: IGNITION RELAY — × — — PCS-49
B2555: STOP LAMP — × — — SEC-52
B2556: PUSH-BTN IGN SW — × × — SEC-54
B2557: VEHICLE SPEED × × × — SEC-56
B2560: STARTER CONT RELAY × × × — SEC-57
B2562: LOW VOLTAGE — × — — BCS-40
B2601: SHIFT POSITION × × × — SEC-58
B2602: SHIFT POSITION × × × — SEC-61
B2603: SHIFT POSI STATUS × × × — SEC-63
B2604: PNP SW × × × — SEC-66
B2605: PNP SW × × × — SEC-68
B2606: S/L RELAY × × × — SEC-70
B2607: S/L RELAY × × × — SEC-71
B2608: STARTER RELAY × × × — SEC-73
B2609: S/L STATUS × × × — SEC-75
B260A: IGNITION RELAY × × × — PCS-51
B260B: STEERING LOCK UNIT — × × — SEC-79
B260C: STEERING LOCK UNIT — × × — SEC-80
B260D: STEERING LOCK UNIT — × × — SEC-81
B260F: ENG STATE SIG LOST × × × — SEC-82
B2612: S/L STATUS × × × — SEC-86
B2614: ACC RELAY CIRC — × × — PCS-53
B2615: BLOWER RELAY CIRC — × × — PCS-57
B2616: IGN RELAY CIRC — × × — PCS-59
B2617: STARTER RELAY CIRC × × × — SEC-90
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure INFOID:0000000003135124
Light reminder warning chime does not sound even though headlamp is illuminated. B
Diagnosis Procedure INFOID:0000000003135126
WCS
• Seat belt warning does not sound even though driver seat belt is not fastened.
• Seat belt warning sounds even though driver seat belt is fastened.
Diagnosis Procedure INFOID:0000000003135128
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted. D
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING: E
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
F
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this G
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
H
WCS